Professional Documents
Culture Documents
Define Setup for Cabinet Cabinet Type: Select 6102 RUS Power System: Select 100-250 VAC, optional backup Climate System: Select Extended Note: Power system should be configured to the power that is coming into the cabinet. Read descriptions on the right side to select the correct configuration. Click OK after Define Setup for Cabinet is complete
GSM Guide for TMO Modernization for RBB11_1A (4A, 4B and 4B Lite).
The example in this document shows 3x3 (3+3+3) @ 43 dB (20W)
Antenna Sector Setup Number of Sectors: Select 3 Frequency: Select GSM 1900 B2 RX Diversity: Select 2-Way Antenna Sharing: Select Yes TMA: Select TMA Click RE Setup after Antenna Sector Setup is complete
Radio Equipment Setup RE Type: Select RUS 01 Radio Mode: Select Single Number of TRX/MCTR: Select 3 for all sectors Note: Number of TRX configuration is Site Specific. Click OK after RE Setup is complete, then Click OK on Antenna Sector Setup.
Transmission Setup STN Equipment: Select No STN (default) RBS Transmission Interface: Select T1 Click OK when completed
Final Configuration Selection Select Run RBS configuration wizard Click OK after Final Configuration Selection is complete
GSM Guide for TMO Modernization for RBB11_1A (4A, 4B and 4B Lite).
The example in this document shows 3x3 (3+3+3) @ 43 dB (20W)
Define RU Position DUG 0: Shelf: B3 Slot: 2 RUS 0: Shelf: C3 Slot: 5 RUS 1: Shelf: C3 Slot: 9 RUS 2: Shelf: C3 Slot: 13 Note: Leave all other parameters undefined Click OK after Define RU Position is complete
Define Node Parameters Support system control: Select False Hub position: Select A6 Click OK after Define Node Parameters is complete Note: Logical Name is the GSM site ID and Full Distinguished name is the DUW PCS Site ID
Define MCTR Configuration Power settings should be set at 3x43dBm: only change value if requested to do so. Click OK
GSM Guide for TMO Modernization for RBB11_1A (4A, 4B and 4B Lite).
The example in this document shows 3x3 (3+3+3) @ 43 dB (20W)
Define Transmission Network Topology: Select Cascade if LMU is present and Standalone if LMU is not present Sync Source: Select PCMA for one T1, select PCMA and PCMC for two T1, and Select PCMA, PCMC, and PCMD for three T1. Note: PCMB is never check Click OK after Define Transmission is complete
Define TEI for DUG 0: Leave TEI Value as default (62) Click OK
GSM Guide for TMO Modernization for RBB11_1A (4A, 4B and 4B Lite).
The example in this document shows 3x3 (3+3+3) @ 43 dB (20W)
You will do this for each sector. Select GSM, Delay and Gain and then click OK. Example: <TmaSector sectorNumber="1" tmaType="TMA" typeOfRet="NONE" internalPower="YES" ulGain="120" dlTrafficDelayA="300" ulTrafficDelayA="300" dlTrafficDelayB="300" ulTrafficDelayB="300" dlAttenuation="5" tmaDegradedSupported="NO" currentLowLimA="50" currentLowLimB="50" currentHighLimA="180" currentHighLimB="180" />
You will do this for each sector. Select Externally Powered, Delay and Gain and then click OK. Example: <TmaSector sectorNumber="1" tmaType="TMA" typeOfRet="NONE" internalPower="YES" ulGain="120" dlTrafficDelayA="300" ulTrafficDelayA="300" dlTrafficDelayB="300" ulTrafficDelayB="300" dlAttenuation="5" tmaDegradedSupported="NO" currentLowLimA="50" currentLowLimB="50" currentHighLimA="180" currentHighLimB="180" />
Define ALNA/TMA Parameters: GSM TMA Type: GSM TX Group Delay: 300 (dlTrafficDelayA) RX Group Delay: 300 (ulTrafficDelayA) Loss: 120x0.1=12 (Loss must be Negative #) Repeat for all sectors
Define ALNA/TMA Parameters: Externally Power TMA Type: Externally Powered TX Group Delay: 300 (dlTrafficDelayB) RX Group Delay: 300 (ulTrafficDelayB) Loss: 120x0.1=12 (Loss must be Negative #)(ulGain) Repeat for all sectors
GSM Guide for TMO Modernization for RBB11_1A (4A, 4B and 4B Lite).
The example in this document shows 3x3 (3+3+3) @ 43 dB (20W)
OMT Wizard- Save IDB: Click YES Note: Name it the site ID you are working on