You are on page 1of 32

GWC Valve International

Proven technology for individual valve solutions worldwide

CAST STEEL VALVES GATE, GLOBE & CHECK


PRESSURE CLASS: ASME 150-1500 SIZE RANGE: 2 - 60 API STANDARDS: 600 & 603 ASME B16.34

Catal og Nu mb er CSV- 10 0 3

TABLE OF CONTENTS
Gate Valve Standard Features Globe Valve Standard Features Swing Check Valve Standard Features Ordering Guide Class 150 Class 300 Class 600 Class 900 Class 1500 4 6 8 9

C ast S teel G ate V alves


10 11 11 12 12

C ast S teel G lobe


Class 150 Class 300 Class 600 Class 900 Class 1500

and

A ngle V alves

13 14 14 15 15

C ast S teel S wing C heck V alves


Class 150 Class 300 Class 600 Class 900 Class 1500 16 17 17 18 18

C ast S tainless S teel G ate V alves


Class 150 Class 300 19 19

C ast S tainless S teel G lobe V alves


Class 150 Class 300 20 20

C ast S tainless S teel S wing C heck V alves


Class 150 Class 300 O-Ring Seal Block & Bleed Gate Valves Cast Steel Cryogenic Gate, Globe and Check Valves PressureTemperature Ratings Terms and Conditions of Sale Return Goods Policy, Warranty 21 21 22 24 26 28 29

GWC Valve International


3

gate valve Standard features


Handwheel Nut Handwheel Yoke Cap Stem Nut Gland Adjustment Nut Gland Eyebolt Gland Proper Gland Eyebolt Pin Gland Flange Packing Backseat Bushing Bonnet Bolt Bonnet Nameplate Bonnet Nut Gasket Gate Body

GWC Gate Valves are manufactured to the latest edition of API Standard 600 and tested to API Standard 598.

APPLICATION & FUNCTION

Stem

Gate valves are primarily used for stop valves fully opened or fully closed. They are not normally considered for throttling purposes, but more for slurries, viscous fluids, etc. Gate valves are characterized by a traveling wedge, which is moved with the operation of the stem nut. The wedge travels perpendicular to the direction of the flow. Gate valves usually have a minimum pressure drop when fully open, provide tight shut-off when fully closed, and remain relatively free of contamination buildup.

BODY & BONNET

The design of the body and bonnet is calculated to achieve the most regular distribution of stress in all directions, as well as the minimum turbulence and resistance to flow. Valve bonnets are equipped with a backseat bushing. The yoke is integrally cast on Pressure Classes 150 and 300 up to 12 and up to 10 on Class 600 and higher ratings.

Body Seat Ring

BODY-BONNET JOINT

Standard body-bonnet joints of gate valves are machined as follows: PRESSURE CLASS 150 300, 600 900* & over JOINT DESIGN Flat Faced Male-and-Female Ring Type Joint

*Pressure Class 600 also available in Ring Type Joint. GWC can supply any style of gasket required by customer.

GWC Valve International

GATE

All gates are fully guided to the seats. As standard our valves are supplied with a solid flexible gate that has a tapered H cross-section. The flexible wedge is cast or machined with a circumferential groove to allow the seating surfaces to move independently and adjust to movement of the body seats. This design is beneficial where line loads or thermal expansion of the system is likely to distort the seat face in the valve. This design of gate is ideally suited for steam or other high temperature services and is especially useful to prevent sticking where valves are closed when hot and opened when cold.

SEAT RING

Seat rings are designed to greatly reduce and/or prevent any turbulence and avoid damages due to the corrosion. The seat rings are forged or rolled in one piece, and then seal welded and overlaid, if required. After welding and all required heat treating, the seat ring faces are machined, thoroughly cleaned and inspected before leaving for assembly.

STEM

The stem connection to the gate is a T-head design which is integral (without welding) with the stem. The accuracy in the dimensions and finishes assure a long life with a perfect tightness in the packing area, resulting in lower fugitive emissions. The stem-to-gate connection is designed to prevent the turning or the disengagement of stem from the wedge while the valve is in service.

gate valve Standard features


Through calculations and extreme testing, the strength of the stem-to-gate connection has proven to exceed the strength of the stem at the root of its operating thread.

STEM PACKING

The stem packing is designed and arranged to ensure a maximum seal along the stem during operation or while at position, thus allowing for a greater reduction in fugitive emissions. Our packings are NON-ASBESTOS types. GWC can supply any style of packing required by our customer.

STUFFING BOX

The depth of the stuffing box allows for a sufficient amount of packing, which makes the stem seal. Our standard packing arrangement and stuffing box design meets <100 ppm fugitive emission requirements. If specified in the purchase order, lantern rings and/or grease injectors can be furnished.

PACKING GLAND

The packing gland design is a two-piece self-aligning type. The packing gland has a spherical head that rides within the spherical joint of the gland flange. The packing gland has a shoulder, which restricts the complete entry into the stuffing box bore. This particular design assures a straight compression of the packing as the gland eyebolts are being equally adjusted, without injuring the stem.

STEM NUT

The stem nut arrangement and design allows for the removal of the handwheel without allowing the stem and gate to drop into the closed position if the handwheel is removed while the valve is in the open position. Ball bearings are provided in the stem nut arrangement of Class 150 valves from NPS 14, on Class 300 valves from NPS 12:, on Class 600 valves from NPS 6, and on Classes 900-1500 valves from NPS 2.

HANDWHEELS

Handwheels are designed for easy operation and a comfortable grip. Our valves are also available with gearing, motor actuators or cylinder actuators for the more demanding services. For normal service conditions, ASTM A194 Class 2H and ASTM A193 Grade B7 nuts and stud bolts are furnished. If specified for high temperature service conditions, ASTM A194 Class 4 and ASTM A193 Grade B16 nuts and stud bolts are furnished. Standard bolting furnished for our stainless steel valves consists of ASTM A194 Class 8 and ASTM A193 Grade B8 nuts and stud bolts. GWC can supply any bolting as required by the customer.

END CONNECTIONS

Our standard production covers valves with: Flange ends with Raised Face (RF), Flat Face (FF) or Ring Type Joint (RTJ) that conform to B16.5. Butt-welding ends (BW) that conform to B16.25. All face-to-face/end-to-end dimensions conform to B16.10. Other special end connections are supplied according to customers requirements.

ACCESSORIES

Accessories such as gear operators, actuators, bypasses, locking devices, chainwheels, extended stems and bonnets for cryogenic service and many others are available to meet the customers requirements.

GWC Valve International


5

BOLTS AND NUTS

globe valve Standard features


Handwheel Nut Handwheel Stem Nut Stem Gland Flange Gland Eyebolt Gland Eyebolt Pin Bonnet Bolt Bonnet Nut Bonnet Nameplate Gland Adjustment Nut Gland Proper Packing Backseat Bushing Gasket Body Disc Nut Disc Seat Ring

GWC Globe Valves are manufactured and modified to the latest edition of API Standard 600/ASME B16.34 and tested to API Standard 598.

APPLICATION & FUNCTION

Globe valves are primarily used as control valves where throttling or both throttling and shut-off are required. Globe valves can also be used for on-off service; however, because of the design, a pressure drop becomes inherent. This is generally confined to on-off applications where the valve is normally closed and pressure drop is not important when the valve is open. Normal applications will find the globe valve with the flow and pressure under the disc. GWC cast steel globe valves are commonly made in outside screw and yoke designs with full ports (including seat ring) and heavy-duty, conical plug type discs.

The body is full ported and spherical in form. The design utilizes large radiuses which allow for the stresses, flow resistance and turbulence to be kept to a minimum. Valve bonnets are equipped with a backseat bushing.

BODY & BONNET

BODY-COVER JOINT
PRESSURE CLASS 150, 300, 600 900* & over

Standard body-cover joints of our globe valves are machined as follows: JOINT DESIGN Male-and-Female Ring Type Joint

*Pressure Class 600 also available in Ring Joint Type GWC can supply any style of gasket required by the customer.

DISC

The valve is normally supplied with the conical plug type disc. The disc rotates freely on the stem and incorporates a differential angle from that on the seat ring. This design provides the maximum assurance of shut off, is less likely to stick in the body seat, and is considered the simplest design for field repair.

GWC Valve International

The disc is held onto the stem utilizing the disc nut and a split-ring disc retainer on 24 in pressure classes 150 and 300. Larger sizes as well as pressure classes 600 and higher utilize the disc nut and a button head design which is integral with the stem. Bottom guided discs are available.

SEAT RINGS

Seat rings are designed to greatly reduce and/or prevent any turbulence and avoid damages due to corrosion. The seat rings are forged or rolled in one piece and then seal welded and overlaid, if required. After welding and all required heat treating, the seat ring faces are machined, thoroughly cleaned and inspected before leaving for assembly.

STEM

As GWCs standard, all stems are rotating and rising; however, a non-rotating design is available when specified by the customer. The accuracy in the dimensions and finishes assure a long life with a perfect tightness in the packing area, resulting in lower fugitive emissions. All of our stems are designed with integral backseat features which provide an ultimate seal during packing changes.

STUFFING BOX

The depth of the stuffing box allows for a sufficient amount of packing, which makes the stem seal. GWCs standard packing arrangement and stuffing box design meets <100 ppm fugitive emission requirements. If specified in the purchase order, lantern rings and/or grease injectors can be furnished.

globe valve Standard features


STEM PACKING
The stem packing is designed and arranged to ensure a maximum seal along the stem during operation or while at position, thus allowing for a greater reduction in fugitive emissions. Our packings are of non-asbestos types. GWC can supply any style of packing required by the customer.

PACKING GLAND

The packing gland design is a two-piece self-aligning type. The packing gland has a spherical head that rides within the spherical joint of the gland flange. The packing gland has a shoulder, which restricts the complete entry into the stuffing box bore. This particular design assures a straight compression of the packing as the gland eyebolts are being equally adjusted, without injuring the stem. The stem nuts on GWCs standard rising stem globe valves are threaded into the top of the yoke where they are secured with a tack weld.

STEM NUT

OPERATION

Handwheels are designed with a comfortable grip for easy operation. As our standard, hammer-blow type handwheels are provided as listed in the next column: PRESSURE CLASS 150 300 600 900 and over JOINT DESIGN 8 and larger 6 and larger 4 and larger

Our valves are also available with gearing, motor actuators or cylinder actuators for the more demanding services.

BOLTS AND NUTS

For normal service conditions, ASTM A194 Class 2H and ASTM A193 Grade B7 nuts and stud bolts are furnished. If specified for high temperature service conditions, ASTM A194 Class 4 and ASTM A193 Grade B16 nuts and stud bolts are furnished. Standard bolting furnished for our stainless steel valves consists of ASTM A194 Class 8 and ASTM A193 Grade B8 nuts and stud bolts. GWC can supply any bolting as requested by the customer.

END CONNECTIONS

Our standard production covers valves with: Flange ends with Raised Face (RF), Flat Face (FF) or Ring Type Joint (RTJ) that conform to B16.5. Butt-welding ends (BW) that conform to B16.25. All face-to-face/end-to-end dimensions conform to B16.10. Other special end connections are supplied according to customers requirements.

ACCESSORIES

Accessories such as gear operators, actuators, bypasses, locking devices, chainwheels, extended stems and bonnets for cryogenic service and many others are available to meet the customers requirements.

GWC Valve International


7

SWING CHECK VALVE STANDARD FEATURES


GWC Swing Check Valves are manufactured and modified to the latest edition of API Standard 600/ASME B16.34 and tested to API Standard 598.
Cover Bolt Cover Nut Gasket Cover Hinge Arm Hinge Pin Body Nameplate

APPLICATION & FUNCTION

Swing check valves are designed to close quickly and automatically with positive shut off in either horizontal or vertical (flow up) pipe runs. Inherently, swing check valves have a low pressure drop and are best suitable for velocity applications. Our closure design allows our swing check valve to close completely even and remain closed with no flow when installed in a horizontal pipe run.

Seat Ring Washer Disc Nut Split Pin Disc

BODY

The body is full ported and spherical in form. The design utilizes large radiuses which allow for the stresses, flow resistance and turbulence to be kept to a minimum. Bosses are provided for optional drains.

BODY-COVER JOINT
PRESSURE CLASS 150, 300, 600 900* & over

Standard body-cover joints of our swing check valves are machined as follows: JOINT DESIGN Male-and-Female Ring Type Joint

*Pressure Class 600 also available in Ring Type Joint. GWC can supply any style of gasket required by customer. The hinge arm pivots on the hinge pin which is located near the discs center of gravity. Body penetration for the hinge pin is sealed with a soft steel gasket and flanged plug. The hinge arm is designed to withstand the shock load of quick closing to insure a longer life and continued shutoff. The hinge arm also has an integral disc stop that provides a positive stop in the open position.

HINGE ASSEMBLY

DISC

Each discs seating surface is precision ground and mated to the seat ring for insurance of a positive shut off. The disc is secured to the hinge arm with the disc nut and pinned to prevent disengagement during service. We can provide either integral or overlaid seat facings at customers request.

GWC Valve International

SEAT RING

Seat rings are designed to greatly reduce and/or prevent any turbulence and avoid damages due to corrosion. The seat rings are forged or rolled in one piece and then seal welded and overlaid, if required. After welding and all required heat treating, the seat ring faces are machined, thoroughly cleaned and inspected before leaving for assembly.

BOLTS AND NUTS

For normal service conditions, ASTM A194 Class 2H and ASTM A193 Grade B7 nuts and stud bolts are furnished. If specified for high temperature service conditions, ASTM A194 Class 4 and ASTM A193 Grade B16 nuts and stud bolts are furnished. Standard bolting furnished for our stainless steel valves consists of ASTM A194 Class 8 and ASTM A193 Grade B8 nuts and stud bolts. GWC can supply any bolting as requested by the customer.

END CONNECTIONS

Our standard production covers valves with: Flange ends with Raised Face (RF), Flat Face (FF) or Ring Type Joint (RTJ) that conform to B16.5. Butt-welding ends (BW) that conform to B16.25. All face-to-face/end-to-end dimensions conform to B16.10. Other special end connections are supplied according to customers requirements.

ACCESSORIES/OPTIONAL DESIGNS

Counterweight features are available as an accessory. Piston, tilting disc or API-6D designs are also available to meet the customers requirements. Drains and bypasses are available as specified by the customer.

Ordering Guide
Example: 8 Figure #1900-I-5-GO

1 90 0
1. 2. 3.

I
4.

5
5.

GO
6.

8 CLASS 900 GATE VALVE, FLG-RF, A217 WC6 BODY, WC6 DISC W/STELLITE OVERLAY, F11 SEATS W/STELLITE OVERLAY, F6 STEM, GEAR OP.

1. MODEL
1 2 3 4 5 6 - - - - - - API 600 GATE VALVE API 600 GLOBE VALVE API 600 SWING CHECK VALVE API 603 GATE VALVE API 603 GLOBE VALVE API 603 SWING CHECK VALVE 24 26 34 35 81 83 - - - - - - ANGLE GLOBE VALVE STOP CHECK VALVE TILTING DISC CHECK VALVE PISTON CHECK VALVE API-6D GATE VALVE API-6D SWING CHECK VALVE

2. RATING
15 - CLASS 150 30 - CLASS 300 60 - CLASS 600 90 - CLASS 900 150 - CLASS 1500

3. END CONNECTION
0 - RF FLANGED 6 - FF FLANGED 7 - BUTTWELD 9 - RING JOINT X - OTHER

4. MATERIAL (Body + Bonnet/Cap)


A B C D H I J - WCB - WCC - LCC - LCB - WC1 - WC6 - WC9 K L M N O P Q - C5 - C12 - CF8 - CF8M - CF3 - CF3M - CF8C R S T U X - CN7M - A890 4A - A890 5A - A890 6A - OTHER

5. MATERIAL (Trim)
1 - 13CR 8 - 13CR 1/2 STELLITE 5 - 13CR FULL STELLITE 2 - 304SS 2S - 304SS 1/2 STELLITE 15 - 304SS FULL STELLITE 10 - 316SS 12 - 316SS 1/2 STELLITE 16 - 316SS FULL STELLITE 9 - MONEL 11 - MONEL 1/2 STELLITE 13 - ALLOY 20 14 - ALLOY 20 1/2 STELLITE 17 - 347SS 17H - 347SS 1/2 STELLITE 17S - 347SS FULL STELLITE 21 - F51 22 - F53 23 - F55 O - OTHER

6. OPERATOR

- HANDWHEEL OPERATOR GO - BEVEL GEAR OPERATOR B - BARE STEM

7. SPECIAL REQUIREMENT
N S - NACE MR-01-75 - SUPPLY COMPLETE INFORMATION EB - EXTENDED BONNET Y - Y PATTERN

GWC Valve International


9

Cast Steel Gate Valves


S tandard P arts & M aterials
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
BODY BONNET GATE SEAT RING YOKE HANDWHEEL STEM BACKSEAT BUSHING GLAND FLANGE PACKING GLAND YOKE CAP BONNET BOLT BONNET NUT GLAND EYEBOLT GLAND ADJUSTMENT NUT HANDHWEEL NUT GLAND EYEBOLT PIN PACKING GASKET YOKE BOLT YOKE NUT NAMEPLATE

PART NAME

CARBON STEEL TYPE WCB


A216 WCB A216 WCB A216 WCB+13CR A105+STELLITE A216 WCB MALLEABLE IRON A182 F6 A276 410 A216 WCB A276 410 AISI 1045 A193 B7 A194 2H A193 B7 A194 2H AISI 1045 AISI 1045

ALLOY STEEL TYPE WC6


A217 WC6 A217 WC6 A217 WC6+13CR A182 F11+STELLITE A217 WC6 MALLEABLE IRON A182 F6 A276 410 A217 WC6 A276 410 AISI 1045 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045

STAINLESS STEEL TYPE C12


A217 C12 A217 C12 A217 C12+13CR A182 F9+STELLITE A217 C12 MALLEABLE IRON A182 F6 A276 410 A217 C12 A276 410 AISI 1045 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045

TYPE LCC
A352 LCC A352 LCC A352 LCC+316SS LF2+STELLITE A352 LCC MALLEABLE IRON A182 F316 A276 316 A352 LCC A276 316 AISI 1045 A320 L7 A194 4 A320 L7 A194 4 AISI 1045 AISI 1045

TYPE WC9
A217 WC9 A217 WC9 A217 WC9+13CR A182 F22+STELLITE A217 WC9 MALLEABLE IRON A182 F6 A276 410 A217 WC9 A276 410 AISI 1045 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045

TYPE C5
A217 C5 A217 C5 A217 C5+13CR A182 F5+STELLITE A217 C5 MALLEABLE IRON A182 F6 A276 410 A217 C5 A276 410 AISI 1045 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045

TYPE CF8M
A351 CF8M A351 CF8M A351 CF8M A182 F316+STELLITE A351 CF8M MALLEABLE IRON A182 F316 A276 316 A351 CF8M A276 316 A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316

BRAIDED GRAPHITE & DIE FORMED GRAPHITE RINGS CLASS 150 316SS GRAPHITE REINFORCED CORRUGATED SHEET / CLASS 300 SPIRAL WOUND 316SS + GRAPHITE / CLASS 600 & ABOVE SOFT RING JOINT A193 B7 A194 2H STAINLESS STEEL A320 L7 A194 4 STAINLESS STEEL A193 B16 A194 4 STAINLESS STEEL A193 B16 A194 4 STAINLESS STEEL A193 B16 A194 4 STAINLESS STEEL A193 B16 A194 4 STAINLESS STEEL A193 B8 A194 8 STAINLESS STEEL

M odel 1150 / 1157 / 1159


Cast steel gate valve, outside screw and yoke, bolted bonnet, rising stem, non-rising handwheel, flexible wedge, available in welded seat rings, designed according to API-600. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5* ASME B16.25 ASME Class 150

Other materials available on request.

D1

H Open D2

H Open

GWC Valve International

L1,L2

L3

* 26 and larger are available with ASME B16.47 end flanges, either Series A or Series B (formerly MSS SP-44 and API 605).

C lass 150
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW 1-1/2"
40mm 50mm

Dimensions in inches
2" 2-1/2"
65mm 80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

750mm

30"

900mm

36"

6.50 7.00 6.50 12.76 7.09 36 31

7.00 7.50 8.50 14.45 7.87 41 36

7.50 8.00 9.50 15.63 7.87 58 47

8.00 8.50 11.13 18.03 8.82 73 61

9.00 9.50 12.00 22.05 9.84 12.40 106 86

10.50 11.00 15.88 30.04 12.40 12.40 192 166

11.50 12.00 16.50 37.80 13.98 12.40 284 242

13.00 13.50 18.00 45.91 15.75 13.98 397 327

14.00 14.50 19.75 53.90 17.72 15.75 618 513

15.00 15.50 22.50 59.65 19.69 15.75 904 774

16.00 16.50 24.00 71.80 22.05 15.75 1,279 1,126

17.00 17.50 26.00 74.80 24.80 17.72 1,488 1,296

18.00 18.50 28.00 83.50 27.95 17.72 1,856 1,632

20.00 20.50 32.00 98.50 31.50 19.69 3,042 2,703

24.00 36.00

28.00 40.00

126.00 140.20 35.43 27.95 4,630 3,944 43.00 31.50 6,400 6,305

10

Cast Steel Gate Valves


M odel 1300 / 1307 / 1309
Cast steel gate valve, outside screw and yoke, bolted bonnet, rising stem, non-rising handwheel, flexible wedge, available in welded seat rings, designed according to API-600. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5* ASME B16.25 ASME Class 300

D1

H Open D2

H Open

* 26 and larger are available with ASME B16.47 end flanges, either Series A or Series B (formerly MSS SP-44 and API 605).

C lass 300
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW 1-1/2"
40mm 50mm

L1,L2

L3

Dimensions in inches
2" 2-1/2"
65mm 80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

750mm

30"

900mm

36"

7.50 8.00 7.50 15.00 7.87 40 29

8.50 8.13 8.50 15.94 7.87 58 49

9.50 10.13 9.50 17.32 7.87 75 60

11.13 11.83 11.13 19.69 8.82 110 84

12.00 12.63 12.00 23.31 9.84 12.40 165 119

15.83 16.50 15.83 32.13 13.98 12.40 317 251

16.50 17.13 16.50 41.02 15.75 12.40 550 462

18.00 18.63 18.00

19.75 20.38 19.75

30.00 30.63 30.00 62.52 22.05 15.75 1,496 1,232

33.00 33.63 33.00 74.41 24.80 19.69 2,139 1,793

36.00 36.63 36.00 80.31 27.95 19.69 2,772 2,354

39.00 39.75 39.00 86.50 31.50 19.69 3,545 3,058

45.00 45.83 45.00

55.00 56.00 55.00

68.00 69.00 68.00

48.31 56.77 17.72 13.98 704 561 19.69 15.75 1,056 808

121.18 127.60 159.06 35.43 24.80 5,346 4,367 51.02 31.50 8,316 7,040 63.00 51.02 16,698 14,960

M odel 1600 / 1607 / 1609


Cast steel gate valve, outside screw and yoke, bolted bonnet, rising stem, non-rising handwheel, flexible wedge, available in welded seat rings, designed according to API-600. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5* ASME B16.25 ASME Class 600

D1

* 26 and larger are available with ASME B16.47 end flanges, either Series A or Series B (formerly MSS SP-44 and API 605).

C lass 600
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW
50mm

L1,L2

L3

Dimensions in inches
2" 2-1/2"
65mm 80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

750mm

30"

11.50 11.63 11.50 16.65 7.87 80 69

13.00 13.13 13.00 17.99 8.82 113 97

14.00 14.13 14.00 20.12 9.84 143 122

17.00 17.13 17.00 25.00 13.98 12.40 277 220

22.00 22.13 22.00 37.72 17.72 15.75 532 423

26.00 26.13 26.00 42.44 19.69 17.72 935 744

31.00 31.13 31.00 48.86 24.80 19.69 1,385 1,102

33.00 33.13 33.00 56.69 27.95 22.05 1,984 1,578

35.00 35.13 35.00 50.09 31.50 24.80 2,658 2,283

39.00 39.13 39.00 71.06 35.43 27.96 3,108 2,473

43.00 43.13 43.00 78.11 35.43 27.96 4,891 42,40

47.00 47.25 47.00 79.92 42.99 31.50 6,197 5,371

55.00 55.38 55.00

65.00 65.50 65.00

107.00 155.98 42.99 31.50 8,656 7,473 63.00 35.43 14,840 12,810

GWC Valve International


11

H Open D2

H Open

Cast Steel Gate Valves


M odel 1900 / 1907 / 1909
Cast steel gate valve, outside screw and yoke, bolted bonnet, rising stem, non-rising handwheel, flexible wedge, available in welded seat rings, designed according to API-600.

D1

H Open D2

H Open L3

Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 900

L1,L2

Dimensions in inches

C lass 900

Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW

50mm

2"

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

14.50 14.63 14.50 18.66 9.84 178 165

15.00 15.13 15.00 23.03 13.98 219 191

18.00 18.13 18.00 27.64 13.98 307 251

24.00 24.13 24.00 37.72 19.69 17.72 750 641

29.00 29.13 29.00 50.98 24.80 22.05 1,279 1,113

33.00 33.13 33.00 57.13 24.80 24.80 1,963 1,552

38.00 38.13 38.00 65.16 31.50 24.80 3,160 2,670

40.50 40.87 40.50 72.52 35.43 27.95 4,395 3,740

44.50 44.87 44.50 84.61 35.43 27.95 5,940 5,078

48.00 48.50 48.00 87.80 42.99 31.50 7,662 6,534

52.00 52.50 52.00 97.10 42.99 35.43 9,620 8,010

61.00 61.75 61.00 111.81 42.99 35.43 14,454 12,117

M odel 11500 / 11507 / 11509


Cast steel gate valve, outside screw and yoke, bolted bonnet, rising stem, non-rising handwheel, flexible wedge, available in welded seat rings, designed according to API-600.

D1

H Open D2

GWC Valve International

H Open L3

Dimensions Face to Face End Flange Buttweld Rating


L1,L2

ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 1500

Dimensions in inches

C lass 1500

12

Cast Steel Globe & Angle Valves


S tandard P arts
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1

and

M aterials
STAINLESS STEEL TYPE CF8M
A351 CF8M A351 CF8M A351 CF8M A182 F316+STELLITE MALLEABLE IRON A182 F316 A276 316 A351 CF8M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316 A276 316

PART NAME
BODY BONNET GATE SEAT RING HANDWHEEL STEM BACKSEAT BUSHING GLAND FLANGE PACKING GLAND BONNET BOLT BONNET NUT GLAND EYEBOLT GLAND ADJUSTMENT NUT HANDHWEEL NUT GLAND EYEBOLT PIN DISC NUT PACKING GASKET

CARBON STEEL TYPE WCB


A216 WCB A216 WCB A216 WCB+13CR A105+STELLITE MALLEABLE IRON A182 F6 A276 410 A216 WCB A276 410 A193 B7 A194 2H A193 B7 A194 2H AISI 1045 AISI 1045 A276 410

ALLOY STEEL TYPE WC6


A217 WC6 A217 WC6 A217 WC6+13CR A182 F11+STELLITE MALLEABLE IRON A182 F6 A276 410 A217 WC6 A276 410 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045 A276 410

TYPE LCC
A352 LCC A352 LCC A352 LCC+316SS LF2+STELLITE MALLEABLE IRON A182 F316 A276 316 A352 LCC A276 316 A320 L7 A194 4 A320 L7 A194 4 AISI 1045 AISI 1045 A276 316

TYPE WC9
A217 WC9 A217 WC9 A217 WC9+13CR A182 F22+STELLITE MALLEABLE IRON A182 F6 A276 410 A217 WC9 A276 410 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045 A276 410

TYPE C5
A217 C5 A217 C5 A217 C5+13CR A182 F5+STELLITE MALLEABLE IRON A182 F6 A276 410 A217 C5 A276 410 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045 A276 410

TYPE C12
A217 C12 A217 C12 A217 C12+13CR A182 F9+STELLITE MALLEABLE IRON A182 F6 A276 410 A217 C12 A276 410 A193 B16 A194 4 A193 B16 A194 4 AISI 1045 AISI 1045 A276 410

BRAIDED GRAPHITE & DIE FORMED GRAPHITE RINGS CLASS 150 & 300 SPIRAL WOUND 316SS + GRAPHITE / CLASS 600 & ABOVE SOFT RING JOINT STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL

Other available on request. NAMEPLATE 19 materials

Other materials available on request.

M odel 2150 / 2157 / 2159


Cast steel globe valve, outside screw and yoke, bolted bonnet, rising stem, rising handwheel, swivel plug disc. Available in welded seat rings designed according to API600/ASME B16.34. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 150
L1,L2 L3 K D1

D1

Dimensions in inches
Valve Size L1: RF Face to Face L2: RTJ L3: BW K: RF/BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW 1-1/2"
40mm 50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

C lass 150

6.50 7.00 6.50 3.25 11.42 7.09 38 33

8.00 8.50 8.00 4.00 12.44 2.87 46 36

8.50 9.00 8.50 4.25 12.99 2.87 62 53

9.50 10.00 9.50 4.75 14.37 8.82 75 60

11.50 12.00 11.50 5.75 16.30 11.02 114 90

16.00 16.50 16.00 8.00 19.87 13.98 13.98 209 163

19.50 20.00 19.50 9.75 24.53 15.75 17.72 371 316

24.50 25.00 24.50 12.25 31.61 17.72 17.72 534 426

27.50 28.00 27.50 13.75 33.03 19.69 19.69 891 786

31.00 31.50 31.00 15.50 52.99 22.05 22.05 1,365 1,234

36.00 36.50 36.00 18.00 60.98 24.80 24.80 1,808 1,655

38.50 39.00 38.50 70.00 31.50 27.95 2,156 1,964

38.50 39.00 38.50 78.98 31.50 31.50 2,822 2,597

GWC Valve International


13

H D2

H Open

H Open

Cast Steel Globe & Angle Valves


M odel 2300 / 2307 / 2309
D1

D1

Cast steel globe valve, outside screw and yoke, bolted bonnet, rising stem, rising handwheel, swivel plug disc. Available in welded seat rings designed according to API600/ASME B16.34. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 300 Dimensions in inches
50mm
H Open

H D2

H Open L3

L1,L2

C lass 300

Valve Size L1: RF Face to Face L2: RTJ L3: BW K: RF/BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

10.50 11.13 10.50 5.25 13.78 7.87 58 53

11.50 12.13 11.50 5.75 15.39 8.82 88 80

12.50 13.13 12.50 6.25 16.54 11.02 116 94

14.00 14.63 14.00 7.00 19.37 13.98 176 142

17.50 18.13 17.50 8.75 24.41 17.72 17.72 370 299

22.00 22.63 22.00 11.00 31.22 22.05 19.69 546 440

24.50 25.13 24.50 12.25 45.08 22.05 22.05 1,005 860

28.00 28.63 28.00 14.00 49.61 24.80 24.80 1,340 1,143

33.00 33.63 33.00 55.28 27.95 24.80 2,008 1,720

34.00 34.63 34.00 62.99 27.95 27.96 2,650 2,260

M odel 2600 / 2607 / 2609


D1

D1

GWC Valve International

Cast steel globe valve, outside screw and yoke, bolted bonnet, rising stem, rising handwheel, swivel plug disc. Available in welded seat rings designed according to API600/ASME B16.34. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 600 Dimensions in inches
50mm
H Open

H D2

H Open L3

L1,L2

C lass 600

Valve Size L1: RF Face to Face L2: RTJ L3: BW K: RF/BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

11.50 11.63 11.50 5.25 15.43 8.82 82 68

13.00 13.13 13.00 5.75 17.00 11.02 89 70

14.00 14.13 14.00 6.25 18.82 12.40 137 109

17.00 17.13 17.00 8.00 20.87 13.98 13.98 253 198

22.00 22.13 22.00 9.75 26.57 19.69 19.69 525 415

26.00 26.13 26.00 11.75 28.39 22.05 22.05 800 637

31.00 31.13 31.00 13.25 38.27 24.80 22.05 1,505 1,235

33.00 33.13 33.00 15.00 42.28 27.95 24.80 1,984 1,671

14

Cast Steel Globe & Angle Valves


M odel 2900 / 2907 / 2909
Cast steel globe valve, outside screw and yoke, bolted bonnet, rising stem, rising handwheel, swivel plug disc. Available in welded seat rings designed according to API600/ASME B16.34. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 900
K L1,L2 L3 K D1

D1

H D2

H Open

H Open

Dimensions in inches

Valve Size L1: RF Face to Face L2: RTJ L3: BW K: RF/BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW

50mm

2"

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

C lass 900

14.50 14.63 14.50 7.25 19.57 12.40 215 160

15.00 15.13 15.00 7.50 20.20 13.98 225 180

18.00 18.13 18.00 9.00 23.74 15.75 15.75 390 330

24.00 24.13 24.00 12.00 28.70 22.05 19.69 920 650

29.00 29.13 29.00 38.10 24.80 22.05 2,673 2,370

33.00 33.13 33.00 55.40 27.95 24.80 4,050 3,700

38.00 38.13 38.00 61.00 31.50 27.95 5,247 4,752

M odel 21500 / 21507 / 21509


Cast steel globe valve, outside screw and yoke, bolted bonnet, rising stem, rising handwheel, swivel plug disc. Available in welded seat rings designed according to API600/ASME B16.34. Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 1500
L1,L2 L3 K D1

D1

Dimensions in inches

Valve Size L1: RF Face to Face L2: RTJ L3: BW K: RF/BW Valve Open Height (H) Handwheel Diameter (D1) Handwheel Diameter (D2) Weight (lbs). RF BW

50mm

2"

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

C lass 1500

14.50 14.62 14.50 7.25 19.57 12.40 215 160

18.50 18.62 18.50 8.25 23.00 15.75 13.98 462 265

21.50 21.62 21.50 9.25 28.10 15.75 15.75 772 425

27.75 28.00 27.75 10.75 36.00 20.00 24.80 1,810 1,500

32.75 33.12 32.75 13.88 46.90 24.80 27.96 4,170 3,540

39.00 39.38 39.00 58.00 28.00 31.50 6,330 5,544

44.50 45.13 44.50 65.00 31.50 31.50 8,712 7,524

GWC Valve International


15

H D2

H Open

H Open

Cast Steel Swing Check Valves


S tandard P arts & M aterials
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NAME
BODY COVER DISC SEAT RING HINGE HINGE PIN DISC NUT DISC WASHER SPLIT PIN COVER BOLT COVER NUT EYE BOLT GASKET NAMEPLATE
STAINLESS STEEL

CARBON STEEL TYPE WCB


A216 WCB A216 WCB A216 WCB+13CR A105+STELLITE A216 WCB A276 410 A193 B7 CARBON STEEL A276 410 A193 B7 A194 2H ASTM A181

ALLOY STEEL TYPE WC6


A217 WC6 A217 WC6 A217 WC6+13CR A182 F11+STELLITE A217 WC6 A276 410 A193 B16 CARBON STEEL A276 410 A193 B16 A194 4 ASTM A181

STA I N L E S S STEEL TYPE C12


A217 C12 A217 C12 A217 C12+13CR A182 F9+STELLITE A217 C12 A276 410 A193 B16 CARBON STEEL A276 410 A193 B16 A194 4 ASTM A181

TYPE LCC
A352 LCC A352 LCC A352 LCC+316SS LF2+STELLITE A352 LCC A276 316 A320 L7 CARBON STEEL A276 316 A320 L7 A194 4 ASTM A181

TYPE WC9
A217 WC9 A217 WC9 A217 WC9+13CR A182 F22+STELLITE A217 WC9 A276 410 A193 B16 CARBON STEEL A276 410 A193 B16 A194 4 ASTM A181

TYPE C5
A217 C5 A217 C5 A217 C5+13CR A182 F5+STELLITE A217 C5 A276 410 A193 B16 CARBON STEEL A276 410 A193 B16 A194 4 ASTM A181

TYPE CF8M
A351 CF8M A351 CF8M A351 CF8M A182 F316+STELLITE A351 CF8M A276 316 A193 B8 STAINLESS STEEL A276 316 A193 B8 A194 8 ASTM A181

CLASS 150 & 300 SPIRAL WOUND 316SS + GRAPHITE / CLASS 600 & ABOVE SOFT RING JOINT STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL STAINLESS STEEL

Other materials available on request.

M odel 3150 / 3157 / 3159


Cast steel swing check valve, horizontal or vertical lines, bolted cover, available in welded seat rings, designed according to API-600/ASME B16.34 Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5* ASME B16.25 ASME Class 150

H Open

GWC Valve International

L1,L2

L3

* 26 and larger are available with ASME B16.47 end flanges, either

C lass 150
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Weight (lbs). RF BW 1-1/2"
40mm 50mm

Series A or Series B (formerly MSS SP-44 and API 605). Dimensions in inches
2" 2-1/2"
65mm 80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

750mm

30"

900mm

36"

6.50 7.00 6.50 5.11 33 28

8.00 8.50 8.00 6.30 38 31

8.50 9.00 8.50 6.70 48 38

9.50 10.00 9.50 7.49 68 56

11.50 12.00 11.50 8.87 110 95

14.00 14.50 14.00 10.18 203 183

19.50 20.00 19.50 12.60 299 266

24.50 25.00 24.50 13.72 430 284

27.50 28.00 27.50 14.96 628 572

31.00 31.50 31.00 15.79 926 804

34.00 34.50 34.00 18.11 1,102 980

38.50 39.00 38.50 19.88 1,411 1,160

38.50 39.00 38.50 22.20 1,720 1,495

51.00 51.50 51.00 26.89 3,285 2,945

60.00 60.50 60.00 36.00 5,077 4,315

77.00 77.50 77.00 41.50 8,160 7,010

16

Cast Steel Swing Check Valves


M odel 3300 / 3307 / 3309
Cast steel swing check valve, horizontal or vertical lines, bolted cover, available in welded seat rings, designed according to API-600/ASME B16.34 Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5* ASME B16.25 ASME Class 300

H Open

L1,L2

L3

* 26 and larger are available with ASME B16.47 end flanges, either Series A or Series B (formerly MSS SP-44 and API 605). Dimensions in inches
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Weight (lbs). RF BW
50mm

C lass 300
2" 2-1/2"
65mm 80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

750mm

30"

900mm

36"

10.50 11.13 10.50 6.30 56 43

11.50 12.13 11.50 7.44 72 55

12.50 13.33 12.50 7.83 108 88

14.00 14.63 14.00 8.94 160 102

17.50 18.13 17.50 10.94 299 240

21.00 21.63 21.00 12.68 406 317

24.50 25.13 24.50 15.08 657 525

28.00 28.63 28.00 17.13 916 750

33.00 33.63 33.00 20.08 1,503 1,241

34.00 34.63 34.00 20.51 1,649 1,305

38.50 39.13 38.50 22.52 2,097 1,803

40.00 40.75 40.00 24.76 2,494 2,150

53.00 53.88 53.00 28.03 4,500 3,870

62.75 63.75 62.75 37.00 5,850 5,020

82.00 83.00 82.00 42.99 10,500 9,450

M odel 3600 / 3607 / 3609


Cast steel swing check valve, horizontal or vertical lines, bolted cover, available in welded seat rings, designed according to API-600/ASME B16.34 Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 600

L1,L2

L3

Dimensions in inches
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Weight (lbs). RF BW
50mm

C lass 600
2"
80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

11.50 11.63 11.50 7.38 71 66

14.00 14.13 14.00 8.25 130 110

17.00 17.13 17.00 10.06 247 223

22.00 22.13 22.00 12.94 474 364

26.00 26.13 26.00 14.31 849 686

31.00 31.13 31.00 18.25 1,351 1,081

33.00 33.13 33.00 19.13 1,918 1,605

35.00 35.13 35.00 22.50 2,068 1,693

39.00 39.13 39.00 26.00 2,976 2,469

43.00 43.13 43.00 28.00 4,451 3,802

47.00 47.25 47.00 31.00 5,269 4,443

55.00 55.38 55.00 34.00 6,634 5,137

GWC Valve International


17

H Open

Cast Steel Swing Check Valves


M odel 3900 / 3907 / 3909
Cast steel swing check valve, horizontal or vertical lines, bolted cover, available in welded seat rings, designed according to API-600/ASME B16.34

H Open

Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 900

L1,L2

L3

C lass 900
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Weight (lbs). RF BW
50mm

Dimensions in inches
2"
80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

350mm

14"

400mm

16"

450mm

18"

500mm

20"

600mm

24"

14.50 14.63 14.50 10.51 161 119

15.00 15.13 15.00 11.42 181 136

18.00 18.13 18.00 12.05 307 235

24.00 24.13 24.00 13.31 582 247

29.00 29.13 29.00 18.11 1,210 1,010

33.00 33.13 33.00 19.69 1,800 1,545

38.00 38.13 38.00 22.75 3,200 2,720

40.50 40.87 40.50 25.47 3,850 3,190

44.50 44.87 44.50 27.95 5,324 4,510

48.00 48.50 48.00 30.90 7,150 5,940

52.00 52.50 52.00 33.46 8,800 7,260

61.00 61.75 61.00 36.61 12,760 9,900

M odel 31500 / 31507 / 31509


Cast steel swing check valve, horizontal or vertical lines, bolted cover, available in welded seat rings, designed according to API-600/ASME B16.34

H Open

GWC Valve International

Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 1500

L1,L2

L3

C lass 1500
Valve Size L1: RF Face to Face L2: RTJ L3: BW Valve Open Height (H) Weight (lbs). RF BW
50mm

Dimensions in inches
2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"

80mm

100mm

150mm

200mm

250mm

300mm

350mm

400mm

450mm

500mm

600mm

14.50 14.63 14.50

18.50 18.63 18.50

21.50 21.63 21.50 13.98 467 362

27.75 28.00 27.75

32.75 33.13 32.75

39.00 39.37 39.00 22.64 3,663 2,930

44.50 45.12 44.50 26.38 5,445 4,310

49.50 50.25 49.50 28.54 7,128 5,600

54.50 55.37 54.50 31.89 9,700 7,720

60.50 61.37 60.50 35.63 13,060 10,395

65.50 66.37 65.50 39.57 16,130 12,770

76.50 77.63 76.50 44.27 23,265 17,820

10.51 11.65 161 119 276 209

18.31 21.26 1,067 813 2,356 1,910

18

Cast Stainless Steel Gate Valves


S tandard P arts & M aterials
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
BODY BONNET GATE HANDWHEEL STEM BACKSEAT BUSHING GLAND FLANGE PACKING GLAND BONNET BOLT BONNET NUT GLAND EYEBOLT GLAND ADJUSTMENT NUT HANDHWEEL NUT GLAND EYEBOLT PIN PACKING GASKET NAMEPLATE
STAINLESS STEEL STAINLESS STEEL

PART NAME

STAINLESS STEEL TYPE CF8M


A351 CF8M A351 CF8M A351 CF8M MALLEABLE IRON A182 F316 A276 316 A351 CF8M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316

TYPE CF8
A351 CF8 A351 CF8 A351 CF8 MALLEABLE IRON A182 F304 A276 304 A351 CF8 A276 304 A193 B8 A194 8 A193 B8 A194 8 A276 304 A276 304

TYPE CF3M
A351 CF3M A351 CF3M A351 CF3M MALLEABLE IRON A182 F316 A276 316 A351 CF3M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316 TEFLON TEFLON STAINLESS STEEL

TYPE CF3
A351 CF3 A351 CF3 A351 CF3 MALLEABLE IRON A182 F304 A276 304 A351 CF3 A276 304 A193 B8 A194 8 A193 B8 A194 8 A276 304 A276 304

TYPE CN7M
A351 CN7M A351 CN7M A351 CN7M MALLEABLE IRON B473 A276 CN7M A351 CN7M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316

STAINLESS STEEL

STAINLESS STEEL

M odel 4150 / 4300


Cast stainless steel gate valve, outside screw and yoke, bolted bonnet, rising stem, non rising handwheel, flexible wedge for Class 150 on 3 and larger and 2 and larger for Class 300. Integral seat designed according to API-603, ASME B16.34.

H Open

Face to Face End Flange Buttweld Rating

ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 150/300


L1 L3

Dimensions in inches
Valve Size Face to Face L1: RF L3: BW
15mm

1/2"

20mm

3/4"

25mm

1"

1-1/2"
40mm

50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

C lass 150

4.25 7.48 3.94 4.85

4.63 7.83 3.94 6.20

5.00 9.17 4.72 9.94

6.50 11.22 5.51 19.20

7.00 13.11 6.30 28.00

7.50 15.08 7.09 38.85

8.00 16.69 7.87 48.00

9.00 20.86 9.84 75.50

10.50 28.74 12.40 126.00

11.50 36.85 13.98 213.00

13.00 43.86 13.98 291.40

14.00 53.89 17.72 434.90

Valve Open Height (H) Handwheel Diameter (D) Weight (lbs).

Dimensions in inches
Valve Size Face to Face L1: RF L3: BW
15mm

1/2"

20mm

3/4"

25mm

1"

1-1/2"
40mm

50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

C lass 300

5.50 8.19 3.93 8.00

6.00 8.30 3.93 10.20

6.50 11.93 4.72 20.30

7.50 13.74 7.09 31.80

8.50 15.35 7.87 49.70

9.50 17.00 7.87 77.30

11.13 19.33 8.82 88.30

12.00 23.15 9.84 173.70

15.88 31.57 13.98 310.00

16.50 39.45 15.75 445.00

18.00 47.87 17.72 657.00

19.75 62.28 19.69 942.60

Valve Open Height (H) Handwheel Diameter (D) Weight (lbs).

GWC Valve International


19

Dimensions

Cast Stainless Steel Globe Valves


S tandard P arts & M aterials
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
BODY BONNET GATE HANDWHEEL STEM BACKSEAT BUSHING GLAND FLANGE PACKING GLAND BONNET BOLT BONNET NUT GLAND EYEBOLT GLAND ADJUSTMENT NUT HANDHWEEL NUT GLAND EYEBOLT PIN DISC NUT PACKING GASKET NAMEPLATE
STAINLESS STEEL STAINLESS STEEL

PART NAME

STAINLESS STEEL TYPE CF8M


A351 CF8M A351 CF8M A351 CF8M MALLEABLE IRON A182 F316 A276 316 A351 CF8M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316 A276 316

TYPE CF8
A351 CF8 A351 CF8 A351 CF8 MALLEABLE IRON A182 F304 A276 304 A351 CF8 A276 304 A193 B8 A194 8 A193 B8 A194 8 A276 304 A276 304 A276 304

TYPE CF3M
A351 CF3M A351 CF3M A351 CF3M MALLEABLE IRON A182 F316 A276 316 A351 CF3M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316 A276 316 TEFLON TEFLON STAINLESS STEEL

TYPE CF8
A351 CF3 A351 CF3 A351 CF3 MALLEABLE IRON A182 F304 A276 304 A351 CF3 A276 304 A193 B8 A194 8 A193 B8 A194 8 A276 304 A276 304 A276 304

TYPE CN7M
A351 CN7M A351 CN7M A351 CN7M MALLEABLE IRON B473 A276 316 A351 CN7M A276 316 A193 B8 A194 8 A193 B8 A194 8 A276 316 A276 316 A276 316

STAINLESS STEEL

STAINLESS STEEL

M odel 5150 / 5300


D

Cast stainless steel globe valve, outside screw and yoke, bolted bonnet, rising stem, non rising handwheel, swivel plug disc. Integral seat designed according to API-603, ASME B16.34.
H Open

Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 150/300 Dimensions in inches

GWC Valve International

L1

L3

C lass 150

Valve Size Face to Face L1: RF L3: BW

15mm

1/2"

20mm

3/4"

25mm

1"

1-1/2"
40mm

50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

4.25 7.50 3.94 6.62

4.63 7.81 3.94 8.20

5.00 8.90 5.51 10.82

6.50 10.25 7.09 20.30

8.00 10.47 7.09 31.34

8.50 11.06 8.87 43.30

9.50 13.46 8.82 55.10

11.50 14.84 11.02 96.25

16.00 16.89 13.98 173.00

19.50 21.97 15.75 320.00

Valve Open Height (H) Handwheel Diameter (D) Weight (lbs).

Dimensions in inches

C lass 300

Valve Size Face to Face L1: RF L3: BW

15mm

1/2"

20mm

3/4"

25mm

1"

1-1/2"
40mm

50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

6.00 7.28 3.94 8.80

7.00 7.64 3.94 11.50

8.00 8.82 5.51 20.70

9.00 10.51 7.09 32.20

10.50 12.99 7.09 58.50

11.50 13.93 7.87 80.00

12.50 15.08 8.84 119.20

14.00 17.44 11.02 171.00

17.50 22.32 15.75 292.00

22.00 27.40 17.72 574.00

Valve Open Height (H) Handwheel Diameter (D) Weight (lbs).

20

Cast Stainless Steel swing Valves


S tandard P arts & M aterials
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NAME
BODY COVER DISC HINGE HINGE PIN DISC NUT DISC WASHER SPLIT PIN COVER BOLT COVER NUT EYE BOLT GASKET NAMEPLATE
STAINLESS STEEL STAINLESS STEEL

STAINLESS STEEL TYPE CF8M


A351 CF8M A351 CF8M A351 CF8M A351 CF8M A276 316 A193 B8 STAINLESS STEEL A276 316 A193 B8 A194 8 ASTM A181

TYPE CF8
A351 CF8 A351 CF8 A351 CF8 A351 CF8 A276 304 A193 B8 STAINLESS STEEL A276 304 A193 B8 A194 8 ASTM A181

TYPE CF3M
A351 CF3M A351 CF3M A351 CF3M A351 CF3M A276 316 A193 B8 STAINLESS STEEL A276 316 A193 B8 A194 8 ASTM A181 TEFLON STAINLESS STEEL

TYPE CF3
A351 CF3 A351 CF3 A351 CF3 A351 CF3 A276 304 A193 B8 STAINLESS STEEL A276 304 A193 B8 A194 8 ASTM A181

TYPE CN7M
A351 CN7M A351 CN7M A351 CN7M A351 CN7M B473 A193 B8 STAINLESS STEEL B473 A193 B8 A194 8 ASTM A181

STAINLESS STEEL

STAINLESS STEEL

M odel 6150 / 6300


Cast stainless steel swing valve, horizontal or vertical lines, bolted cover, integral seat designed according to API-603, ASME B16.34.

H Open

Dimensions Face to Face End Flange Buttweld Rating ASME B16.10 ASME B16.5 ASME B16.25 ASME Class 150/300

L1

L3

C lass 150
Dimensions in inches
Valve Size Face to Face L1: RF L3: BW
15mm

1/2"

20mm

3/4"

25mm

1"

1-1/2"
40mm

50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

4.25 3.26 5.05

4.63 3.50 6.18

5.00 4.00 9.05

6.50 4.72 15.70

8.00 5.43 27.60

8.50 6.10 39.50

9.50 6.30 46.35

11.50 7.91 75.50

14.00 9.76 130.90

19.50 11.53 225.60

24.50 12.99 499.00

27.50 13.94 638.00

Valve Open Height (H) Weight (lbs).

C lass 300
Dimensions in inches
Valve Size Face to Face L1: RF L3: BW
15mm

1/2"

20mm

3/4"

25mm

1"

1-1/2"
40mm

50mm

2"

2-1/2"
65mm

80mm

3"

100mm

4"

150mm

6"

200mm

8"

250mm

10"

300mm

12"

5.50 3.66 7.73

6.00 3.78 9.93

8.50 4.41 22.96

9.50 4.96 32.20

10.50 5.98 39.70

11.50 6.46 79.47

12.50 6.93 88.30

14.00 7.32 152.30

17.50 10.31 234.00

21.00 12.28 379.70

24.50 13.98 498.00

28.00 15.47 638.00

Valve Open Height (H) Weight (lbs).

GWC Valve International


21

o-Ring seal block & bleed gate Valves


Sizes Available: 2 24 Class: 150 & 300

Handwheel Nut Handwheel Yoke Cap Stem Nut Gland Adjustment Nut Gland Eyebolt Gland Proper Gland Eyebolt Pin Gland Flange Packing Backseat Bushing Bonnet Bolt Bonnet Nameplate Bonnet Nut Gasket Gate Body

Stem

Design Features
The dovetail groove feature in the seat ring holds the O-Ring seal in place while allowing it to expand or contract during service and still maintains the proper compression to provide uniform sealing. The precision ground metal to metal seats with the O-Ring feature as secondary seal provides dual seating and eliminates any media contamination. A bleed plug is provided at position G to verify shut-off.

Body Seat Ring O-Ring Bleed Plug

Fire Safe, Vapor Tight Shut-off


Should fire occur burning or damaging the O-Ring seal, metal to metal seats will provide an effective fire-safe shut-off.

Service Recommendations

GWC Valve International

GWC O-Ring Seal Block and Bleed Gate Valves are recommended for hard to hold services such as butane, kerosene, gasoline, propane, diesel oils, fuel oils, jet fuels, steam, air, natural gas, toluene, hydrogen, helium, and oxygen. Manifold tank farms, LPG areas, and airport fueling facilities provide excellent opportunities for savings with the O-Ring Seal Gate Valves. For effective double block and bleed service, the line media should be free of foreign matter and solids in suspension.

Seat Materials
Teflon is considered our standard. It is the most widely used elastomer because of its resistance to corrosive and abrasive conditions. We can also offer other materials. Seat insert materials should be specified along with actual service conditions when ordering.

Type Range Temperature Operating


Teflon (PTFE) -100 F + 400 F

22

CAST STEEL CRYOGENIC GATE, GLOBE & CHECK VALVES


GWC Cryogenic Valves are manufactured to the latest edition of API Standard 600 and/or 603 and tested to API Standard 598.

Handwheel Nut Handwheel Yoke Cap

APPLICATION & FUNCTION


During the processes of production, transportation, storage and usage of liquefied gases, countless technical problems can be experienced. GWCs cryogenic valves are designed to assure safety and reliability under these critical conditions. All of GWCs cryogenic valves are thoroughly cleaned and degreased. Afterwards the end ports are sealed to prevent contamination. This process is performed in an approved and designated clean room.
Gland Eyebolt Nut Gland Flange Gland Eyebolt Gland Eyebolt Pin Gland Proper Packing

Stem Bonnet Bolt Bonnet Gasket Bonnet Nut Backseat Bushing

BODY & BONNET


The design of the body and bonnet is calculated to achieve the most regular distribution of stress in all directions, as well as the minimum turbulence and resistance to flow. The extended bonnet provides a gas column which thermally isolates the stem packing and stem nut from the extreme temperatures so they remain functional. Usually the customer specifies the column length.

Gate Body Seat Ring Body

The body-bonnet joint is bolted using applicable ASTM specified bolting for low temperature/ cryogenic conditions.

GASKET

closures
GATE VALVES All gates are fully guided to the seats. As standard, our valves are supplied with a stellite faced, solid flexible gate that has a tapered H cross-section. The flexible wedge is cast or machined with a circumferential groove to allow the seating surfaces to move independently and adjust to movement of the body seats. GLOBE VALVES The valve is normally supplied with the plug type disc. The disc rotates freely on the stem and incorporates a differential angle from that on the seat ring. This design provides the maximum assurance of shut off, is less likely to stick in the body seat and is considered the simplest design for field repair. Bottom guided discs are available. CHECK VALVES Each discs seating surface is precision ground and mated to the seat ring for insurance of a positive shut off. The disc is bolted to the hinge arm and pinned to prevent disengagement during service. KEL-F and other soft inserts are available upon request.

GWC Valve International


23

We can supply any style of gasket required by our customer; however, we recommend gaskets that are oxygen compatible.

CAST STEEL CRYOGENIC GATE, GLOBE & CHECK VALVES


seat ring
Stellite faced seat rings are standard and provide excellent resistance to seizing and galling. KEL-F inserts are available when extremely tight shut-off is required. Our globe and check valves are supplied with KEL-F or other soft inserts as specified by the customer.

Packing gland
The packing gland design is a two-piece, self-aligning type. The gland proper has a spherical head that rides within spherical joint of the gland flange. The gland proper has a shoulder, which restricts the complete entry into the stuffing box bore. This particular design assures a straight compression of the packing as the gland eyebolts are being equally adjusted, without injuring the stem.

stem
The stem connection to the wedge is a T-head design which is integral (without welding) with the stem. The T-head on NPS 8 and smaller valves are forged. The accuracy in the dimensions and finishes assure a long life with a perfect tightness in the packing area. The stem-to-gate connection is designed to prevent the turning or the disengagement of stem from the wedge while the valve is in service. Through calculations and extreme testing, the strength of the stem-to-gate connection has proven to exceed the strength of the stem at the root of its operating thread.

handwheels
Handwheels are designed for easy operation and a comfortable grip. Our valves are also available with gearing, motor actuators or cylinder actuators for more demanding services.

end connections
Our standard production covers valves with: Flange ends with raised face (RF), flat face (FF) or ring type joint (RTJ) ends that conform to B16.5. Butt-welding (BW) ends that conform to B16.25. All face-to-face/end-to-end dimensions conform to B16.10. Other special end connections are supplied according to customers requirements.

Stem packing
The stem packing is designed and arranged to ensure a maximum seal along the stem during operation or while at position. Our packings are NON-ASBESTOS types. We can supply any style of packing required by our customer.

GWC Valve International

accessories
Accessories such as gear operators, actuators, bypasses, locking devices, chainwheels, and many others are available to meet the customers requirements.

stem nut
The stem nut arrangement and design allows for the removal of the handwheel without allowing the stem and gate to drop into the closed position if the handwheel is removed while the valve is in the open position. Ball bearings are provided in the stem nut arrangement of Class 150 valves from NPS 14, on Class 300 valves from NPS 12, on Class 600 valves from NPS 6, and on Class 900 and Class 1500 valves from NPS 2.

24

PRESSURE-TEMPERATURE RATINGS
ASME B16.34-2009
COLD WORKING PRESSURE, psig
CLASS TEMP F
-20 to 100 200 300 400 500 600 650 700 750 800 850

A216 WCB A105 & LF2


285 260 230 200 170 140 125 110 95 80 65 50 35 20

A352 LCC
290 260 230 200 170 140 125 110 95 80 65 50 35 20

A217 WC6 A182 F11


290 260 230 200 170 140 125 110 95 80 65 50 35 20 20 (a) 20 (a) 20 (a) 15 (a)

A217 WC9 A182 F22


290 260 230 200 170 140 125 110 95 80 65 50 35 20 20 (a) 20 (a) 20 (a) 15 (a)

A217 C5 A182 F5
290 260 230 200 170 140 125 110 95 80 65 50 35 20 20 (a) 20 (a) 20 (a) 15 (a)

A217 C12 A182 F9


290 260 230 200 170 140 125 110 95 80 65 50 35 20 20 (a) 20 (a) 20 (a) 20 (a)

A351 CF8 A182 F304


275 230 205 190 170 140 125 110 95 80 65 50 35 20 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 15(a)

A351 CF8M A182 F316


275 230 205 190 170 140 125 110 95 80 65 50 35 20 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 20(a) 15(a)

A352 CN7M
230 200 180 160 150 140

150

900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500

CLASS

TEMP F
-20 to 100 200 300 400 500 600 650 700 750 800 850

A216 WCB A105 & LF2


740 680 655 635 605 570 550 530 505 410 320 230 135 85

A352 LCC
750 750 730 705 665 605 590 555 505 410 320 225 135 85

A217 WC6 A182 F11


750 750 720 695 665 605 590 570 530 510 485 450 320 215 145 95 65 40

A217 WC9 A182 F22


750 750 730 705 665 605 590 570 530 510 485 450 385 265 175 110 70 40

A217 C5 A182 F5
750 750 730 705 665 605 590 570 530 510 485 375 275 200 145 100 60 35

A217 C12 A182 F9


750 750 730 705 665 605 590 570 530 510 485 450 375 255 170 115 75 50

A351 CF8 A182 F304


720 600 540 495 465 440 430 420 415 405 395 390 380 355 325 255 205 165 135 115 95 75 60 40

A351 CF8M A182 F316


720 620 560 515 480 450 440 435 425 420 420 415 385 365 360 305 235 185 145 115 95 75 60 40

A352 CN7M
600 520 465 420 390 360

300

900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500

(a) Permissible, but not recommended for prolonged usage

GWC Valve International


25

PRESSURE-TEMPERATURE RATINGS
ASME B16.34-2009
COLD WORKING PRESSURE, psig
CLASS TEMP F
-20 to 100 200 300 400 500 600 650 700 750 800 850

A216 WCB A105 & LF2


1480 1360 1310 1265 1205 1135 1100 1060 1015 825 640 460 275 170

A352 LCC
1500 1500 1455 1405 1330 1210 1175 1110 1015 825 640 445 275 170

A217 WC6 A182 F11


1500 1500 1445 1385 1330 1210 1175 1135 1065 1015 975 900 640 430 290 190 130 80

A217 WC9 A182 F22


1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 755 535 350 220 135 80

A217 C5 A182 F5
1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 745 550 400 290 200 125 70

A217 C12 A182 F9


1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 755 505 345 225 150 105

A351 CF8 A182 F304


1440 1200 1075 995 930 885 865 845 825 810 790 780 765 710 650 515 410 330 265 225 185 150 115 85

A351 CF8M A182 F316


1440 1240 1120 1025 955 900 885 870 855 845 835 830 775 725 720 610 475 370 295 235 190 150 115 85

A352 CN7M
1200 1035 930 845 780 720

600

900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500

CLASS

TEMP F
-20 to 100 200

A216 WCB A105 & LF2


2200 2035 1965 1900 1810 1705 1650 1590 1520 1235 955 690 410 255

A352 LCC
2250 2250 2185 2110 1995 1815 1765 1665 1520 1235 955 670 410 255

A217 WC6 A182 F11


2250 2250 2165 2080 1995 1815 1765 1705 1595 1525 1460 1350 955 650 430 290 195 125

A217 WC9 A182 F22


2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1160 800 525 330 205 125

A217 C5 A182 F5
2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1120 825 595 430 300 185 105

A217 C12 A182 F9


2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1130 760 515 340 225 155

A351 CF8 A182 F304


2160 1800 1615 1490 1395 1325 1295 1265 1240 1215 1190 1165 1145 1065 975 770 615 495 400 340 280 225 175 125

A351 CF8M A182 F316


2160 1860 1680 1540 1435 1355 1325 1305 1280 1265 1255 1245 1160 1090 1080 915 710 555 440 350 290 225 175 125

A352 CN7M
1800 1555 1395 1265 1165 1080

GWC Valve International

300 400 500 600 650 700 750 800 850

900

900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450

26

1500

PRESSURE-TEMPERATURE RATINGS
ASME B16.34-2009
COLD WORKING PRESSURE, psig
CLASS TEMP F
-20 to 100 200 300 400 500 600 650 700 750 800 850

A216 WCB A105 & LF2


3705 3395 3270 3170 3015 2840 2745 2665 2535 2055 1595 1150 685 430

A352 LCC
3750 3750 3640 3520 3325 3025 2940 2775 2535 2055 1595 1115 685 430

A217 WC6 A182 F11


3750 3750 3610 3465 3325 3025 2940 2840 2660 2540 2435 2245 1595 1080 720 480 325 205

A217 WC9 A182 F22


3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1930 1335 875 550 345 205

A217 C5 A182 F5
3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 1870 1370 995 720 495 310 170

A217 C12 A182 F9


3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1885 1270 855 565 375 255

A351 CF8 A182 F304


3600 3000 2690 2485 2330 2210 2160 2110 2065 2030 1980 1945 1910 1770 1630 1285 1030 825 670 565 465 380 290 205

A351 CF8M A182 F316


3600 3095 2795 2570 2390 2255 2210 2170 2135 2110 2090 2075 1930 1820 1800 1525 1185 925 735 585 480 380 290 205

A352 CN7M
3000 3590 2330 2110 1945 1800

1500

900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500

CLASS

TEMP F
-20 to 100 200 300 400 500 600 650 700 750 800 850

A216 WCB A105 & LF2


6170 5655 5450 2280 5025 4730 4575 4425 4230 3430 2655 1915 1145 715

A352 LCC
6250 6250 6070 5865 5540 5040 4905 4630 4230 3430 2655 1855 1145 715

A217 WC6 A182 F11


6250 6250 6015 5775 5540 5040 4905 4730 4430 4230 4060 3745 2655 1800 1200 800 545 345

A217 WC9 A182 F22


6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3745 3220 2230 1455 915 570 345

A217 C5 A182 F5
6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3115 2285 1655 1200 830 515 285

A217 C12 A182 F9


6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3745 3145 2115 1430 945 630 430

A351 CF8 A182 F304


6000 5000 4480 4140 3880 3680 3600 3520 3440 3380 3300 3240 3180 2950 2715 2145 1715 1370 1115 945 770 630 485 345

A351 CF8M A182 F316


6000 5160 4660 4280 3980 3760 3680 3620 3560 3520 3480 3460 3220 3030 3000 2545 1970 1545 1230 970 800 630 485 345

A352 CN7M
5000 4320 3880 3520 3240 3000

2500

900 950 1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500

GWC Valve International


27

Terms & Conditions of sale


Scope
These terms and conditions apply to all GWC valve products, and supersedes all previously published terms and conditions. Hereafter, GWC Valve International, Inc. shall be referred to as GWC. Special terms and conditions printed on a buyers order will only apply insofar as they conform to the terms and conditions detailed on these pages. Terms and conditions of an order that change or modify those on this sheet shall not be binding on GWC.

Claims
All claims for shortages, corrections, or deductions must be made within 10 days after receipt of goods. Responsibility for goods lost or damaged in transit rests with carrier, and claims should be filed with the carrier by the consignee. Delivery of material to a common carrier shall be considered delivery to the buyer, and shall be at the buyers risk thereafter.

Delivery Delays
We assume no responsibility for delays in delivery, or defaults resulting from strikes, work stoppages, fires, floods, accidents, war, inability to obtain materials, or any other cause unavoidable and beyond our control.

Approval
All quotations, contracts, orders, or agreements are subject to approval and/or acceptance by the main office of GWC. We reserve the right to correct clerical or stenographic errors in quotations, orders, invoices, and other contracts, agreements, or documents.

Taxes
GWC quotations and/or contracts do not include any municipal, state, or federal sales, excise, use occupational, or other taxes, and any such tax, if paid by us will be charged to the purchaser.

Prices
Possession of price lists will not be accepted by GWC as an obligation, or offer to sell the goods listed therein to anyone. All prices contained therein are subject to change without notice, and supersede all previous lists. All orders will be invoiced at prices in effect at the time of shipment unless quoted in writing.

Catalog Illustrations
Catalog illustrations are actual representations of a certain size of each product line, but do not necessarily represent all sizes in details. We reserve the right to institute changes in materials, designs, and specifications without notice in keeping with our policy of continuing product improvement.

Catalog Weights
Catalog weights represent average weights of products and are in no sense guaranteed.

Changes

GWC Valve International

Orders cannot be cancelled or specifications be changed without the consent of GWC, and then only in terms indemnifying GWC against loss.

Returns
See Return Goods Policy on next page.

Quotations
Goods quoted F.O.B. our service center are subject to prior sale. Prices quoted are valid only for the duration indicated in the quotation. Quoted prices supersede all previous prices, quotations, or contracts, and are subject to change without notice.

Special Orders
Orders for special goods must be in writing and accompanied with detailed prints and/or sets of specifications, unless specifications on the orders are definite and complete. Orders will not be entered with the factory unless this is adhered to. Cancellation charges will be as outlined in our quotations.

Cancellations
Orders placed with us cannot be cancelled without our prior written consent. A cancellation charge will be applicable as outlined in our quotation.

Freight Terms
All shipments are F.O.B. our service centers. See current bulletin for freight allowance.

Warranty
See warranty on reverse side

28

Return goods policy


This policy supersedes all other policies for return goods. I. Goods returned at customers request: A. Material must be: 1. Of our manufacture. 2. In clean, new and saleable condition. It must have been stored inside out of the weather. 3. Shipped from one of our service centers within the 12 calendar months preceding the request for return, and the return will not cause inventory to exceed maximum allowable levels. 4. Personally inspected by a GWC representative prior to its return. 5. Special or non-standard items are non-returnable. B. Return shipments must be prepaid. C. Credit will be allowed at invoice price, less 25% handling cost, and less any freight paid by GWC. D. A Return Goods Card must be furnished by a GWC representative after inspection of the material, and must be returned with the shipment. E. Shipments received without a Return Goods Authorization Card will be refused. Customer will be responsible for any storage and/or return freight. F. Material returned which is not of GWC manufacture, not in clean and saleable condition, or not authorized for return will be returned to the customer freight collect. II. Goods returned because of an error by GWC. A. Material must be in a clean, new, saleable condition. B. Return shipment should be made freight collect. C. Full credit will be allowed. D. Customer must receive Return Goods authorization prior to the return of the material. Return Goods Authorization Card must accompany shipment. Shipments received without Return Goods Authorization Card will be refused. Return Goods Authorization Card should be attached to the packing list. All requests to return material to GWC Valve International, Inc. must be submitted in writing to our National Sales Manager for authorization.

Warranty
GWC Valve International, Inc. warrants each product sold, if the products are of our manufacture, against defects in material and workmanship under normal use and service for a period of one year after date of shipment. This warranty is made to the buyer only, and does not extend to any other party. The obligation of GWC Valve International, Inc. under this warranty is limited to: (a) replacement of any part or parts proven defective in material or workmanship, (b) repair of the product F.O.B. the factory or service center, (c) refund of the purchase price. In the case of product or parts not wholly of GWCs manufacture, GWCs liability under this warranty shall be limited to the extent of GWCs recovery from the manufacturer of such parts under its warranty to GWC. This warranty does not extend to any claims for labor, consequential damages, down time, or any other loss, damage, or expense of any kind arising out of the defect. We do not allow claims for unauthorized repairs, labor, or material. We are not responsible for loss of use, personal injury, lost profits, or any other damages whatsoever in connection with the warranties set forth. No warranty shall apply to any product which has been modified or changed in design or function after leaving GWCs facilities or which is misused or operated beyond its design capabilities, or used for other than its intended purpose. Purchasers of GWC products should consult knowledgeable advisors in the selection of product type and material of construction for their specific use. The buyer assumes all risk of this selection. The buyer shall permit GWC or its authorized representative to inspect the product so that it may determine its obligation. GWCshall be entitled to the return of the defective product or parts. Buyer must notify GWCpromptly upon discover of any claimed defect. No material may be returned without first obtaining written permission from GWC Valve International, Inc.

GWC Valve International


29

GWC Valve International

30

Notes

U SA HEAD Q U ARTERS
GWC Valve Inter national , I nc. 4301 Yeager Way Bak e r sfie ld, CA 93313 Ph: 1-661-834-1775 Fax : 1-661-834-207 2 E-Mail: Sales@GWCvalve.com WWW. GWCValve. com

Catal og Nu mb er CSV- 10 0 3

You might also like