Professional Documents
Culture Documents
5 6 7 8 9 10
Please note that all data and specifications are subject to change without notice. All the trade marks of products and companies mentioned in this data sheet belong to their respective owners. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales.
W83783S
Preliminary
TABLE OF CONTENTS
1. GENERAL DESCRIPTION .......................................................................................................................1 2. FEATURES ..................................................................................................... Error! Bookmark not defined. 2.1 Monitoring Items ...................................................................................................................................2 2.2 Actions Enabling ...................................................................................................................................2 2.3 General..................................................................................................................................................2 2.4 Package .................................................................................................................................................2 3. KEY SPECIFICATIONS............................................................................................................................3 4. PIN CONFIGURATION.............................................................................................................................3 5. PIN DESCRIPTION....................................................................................................................................4 6. FUNCTIONAL DESCRIPTION.................................................................................................................6 6.1 General Description ...............................................................................................................................6 6.2 Access Interface .....................................................................................................................................6 6.2.1 The first serial bus access timing are shown as follow: .....................................................................6 6.2.2 The serial bus timing of the temperature 2 and 3 is shown as follow:................................................7 6.3 Analog Inputs ......................................................................................................................................10 6.3.1 Monitor over 4.096V voltage:.........................................................................................................11 6.3.2 Monitor negative voltage: ..............................................................................................................12 6.3.3 Monitor temperature from thermistor:............................................................................................13 6.3.4 Monitor temperature from Pentium IITM thermal diode or bipolar transistor 2N3904 .....................13 6.4 FAN Speed Count and FAN Speed Control..........................................................................................14 6.4.1 Fan speed count .............................................................................................................................14 6.4.2 Fan speed control...........................................................................................................................15 6.5 Temperature Measurement Machine ....................................................................................................16 6.5.1 The W83783S temperature sensor 2 SMI# interrupt has two modes: ...............................................17 6.5.2 The W83783S temperature sensor 1 SMI# interrupt has three modes..............................................18 6.5.3 The W83783S temperature sensor 1 Over-Temperature (OVT#) has three modes............................19 6.6 Voltage and Fan SMI# mode :..............................................................................................................20 6.6.1 Voltage SMI# mode :......................................................................................................................20 6.6.2 Fan SMI# mode :............................................................................................................................20
-I-
W83783S
Preliminary
7. REGISTERS AND RAM ..........................................................................................................................22 7.1 Configuration Register Index 40h....................................................................................................22 7.2 Interrupt Status Register 1 Index 41h ...............................................................................................23 7.3 Interrupt Status Register 2 Index 42h ..............................................................................................23 7.4 SMI# Mask Register 1 Index 43h ....................................................................................................24 7.5 SMI# Mask Register 2 Index 44h ....................................................................................................25 7.6 Reserved Register Index 45h-- 46h..................................................................................................25 7.7 VID/Fan Divisor Register Index 47h ...............................................................................................26 7.8 Serial Bus Address Register Index 48h............................................................................................26 7.9 Value RAM Index 20h- 3Fh or 60h - 7Fh........................................................................................27 7.10 Voltage ID (VID4) & Device ID - Index 49h......................................................................................29 7.11 Temperature 2 and Temperature 3 Serial Bus Address Register--Index 4Ah.......................................29 7.12 Pin Control Register - Index 4Bh .......................................................................................................30 7.13 IRQ#/OVT# Property Select - Index 4Ch ...........................................................................................31 7.14 FAN IN/OUT and BEEP/GPO# Control Register - Index 4Dh ...........................................................32 7.15 Register 50h ~ 5Fh Bank Select - Index 4Eh ......................................................................................33 7.16 Winbond Vendor ID - Index 4Fh........................................................................................................33 7.17 Winbond Test Register -- Index 50h - 55h (Bank 0) ..........................................................................34 7.18 BEEP Control Register 1-- Index 56h (Bank 0) ..................................................................................34 7.19 BEEP Control Register 2-- Index 57h (Bank 0) ..................................................................................35 7.20 Chip ID -- Index 58h (Bank 0) ...........................................................................................................36 7.21 Diode Selection Register -- Index 59h (Bank 0).................................................................................36 7.22 PWMOUT1 Control Register -- Index 5Ah (Bank 0)......................................................................36-A 7.23 PWMOUT2 Control Register -- Index 5Bh (Bank 0) ..........................................................................37 7.24 PWMOUT1/2 Clock Select Register -- Index 5Ch (Bank 0)................................................................37 7.25 VBAT Monitor Control Register -- Index 5Dh (Bank 0).....................................................................38 7.26 Reserved Register -- Index 5Eh (Bank 0)............................................................................................39 7.27 Reserved Register -- Index 5Fh (Bank 0) ...........................................................................................39 7.28 Temperature Sensor 1 Temperature (High Byte) Register - Index 00h ................................................39 7.29 Temperature Sensor 1 Temperature (Low Byte) Register - Index 00h .................................................39 7.30 Temperature Sensor 1 Configuration Register - Index 01h .................................................................40 7.31 Temperature Sensor 1 Hysteresis (High Byte) Register - Index 02h ....................................................41
- II -
W83783S
Preliminary
7.32 Temperature Sensor 1 Hysteresis (Low Byte) Register - Index 02h .....................................................41 7.33 Temperature Sensor 1 Over-temperature (High Byte) Register - Index 03h.........................................42 7.34 Temperature Sensor 1 Over-temperature (Low Byte) Register - Index 03h .........................................42 7.35 Reserved Register -- Index 50h--52h (BANK4) .................................................................................43 7.36 BEEP Control Register 3 -- Index 53h (Bank 4) .................................................................................43 7.37 Reserved Register -- Index 54h--58h (Bank 4)....................................................................................43 7.38 Real Time Hardware Status Register I -- Index 59h (Bank 4) .............................................................43 7.39 Real Time Hardware Status Register II -- Index 5Ah (Bank 4) ...........................................................44 8. SPECIFICATIONS ...................................................................................................................................46 8.1 Absolute Maximum Ratings.................................................................................................................46 8.2 DC Characteristics...............................................................................................................................46 8.3 AC Characteristics...............................................................................................................................48 8.3.1 Serial Bus Timing Diagram ...........................................................................................................48 9. HOW TO READ THE TOP MARKING .................................................................................................49 10. PACKAGE DIMENTIONS.....................................................................................................................50 11. APPLICATION CIRCUIT OF WINBOND W83783S...........................................................................52
- III -
-1-
W83783S
Preliminary
2. FEATURES
2.1 Monitoring Items
3 thermal inputs from remote thermistors or 2N3904 NPN-type transistors or PentiumTM II (Deschutes) thermal diode output 6 voltage inputs --- typical for Vcore, +3.3V, +12V, -12V, +5V, -5V 3 fan speed monitoring inputs Case open detection input WATCHDOG comparison of all monitored values Programmable hysteresis and setting points (alarm thresholds) for all monitored items
2.3 General
I2CTM serial bus interface 5 VID input pins for CUP Vcore identification (for PentiumTM II) Initial power fault beep (for +3.3V, Vcore) IntelTM LDCM (DMI driver 2.0) support
TM
Acer ADM (DMI driver 2.0) support Winbond hardware monitoring application software (Hardware DoctorTM ) support, for both Windows 95/98 and Windows NT 4.0/5.0 Input clock rate optional for 24, 48, 14.318 Mhz 5V Vcc operation
2.4 Package
24-pin SOP
-2-
W83783S
Preliminary
3. KEY SPECIFICATIONS
Voltage monitoring accuracy Monitoring Temperature Range and Accuracy - 40C to +120C Supply Voltage Operating Supply Current ADC Resolution 3C(Max) 5V 5 mA typ. 8 Bits 1% (Max)
4. PIN CONFIGURATION
VID4 FANIN1 FANIN2 FANIN3/PWMOUT1 OVT# BEEP/GPO# VID3 CLKIN SMI#/PWMOUT2 GNDD SCL SDA
1 2 3 4 5 6 7 8 9 10 11 12
24 23 22 21 20 19 18 17 16 15 14 13
VCC VT1/PII1 VREF VCORE +3.3VIN +12VIN -12VIN -5VIN/VT2/PII2 GNDA VID0 VID1 VID2
-3-
W83783S
Preliminary
5. PIN DESCRIPTION
I/O12t I/O12ts OUT12 AOUT OD12 INt INts AIN - TTL level bi-directional pin with 12 mA source-sink capability - TTL level and schmitt trigger - Output pin with 12 mA source-sink capability - Output pin(Analog) - Open-drain output pin with 12 mA sink capability - TTL level input pin - TTL level input pin and schmitt trigger - Input pin(Analog)
Pin Name
Pin No.
Type
Description
1 2 3 4
Voltage Supply readouts from Pentium IITM. 0V to 5V amplitude fan tachometer input. 0V to 5V amplitude fan tachometer input. 0V to 5V amplitude fan tachometer input. / Fan speed control (PWM) output. This multi-functional pin is programmable. Over temperature Shutdown Output. Beep (Default) / General purpose output This multi-functional pin is programmable. Voltage Supply readouts from Pentium IITM. System clock input. Can select 48MHz or 24MHz or 14.318MHz. The default is 24MHz. System Management Interrupt (open drain). The default state is disabled. Fan speed control (PWM) output. This multi-functional pin is programmable. Internally connected to all digital circuitry. Serial Bus Clock. Serial Bus bi-directional Data. Voltage Supply readouts from Pentium IITM.
OVT# BEEP/GPO# VID3 CLKIN SMI# / PWMOUT2 GNDD SCL SDA VID2
5 6 7 8 9
10 11 12 13
DGROUND INt s
OD12
IN t
-4-
W83783S
Preliminary
Pin Discription, continued
Pin Name
Pin No.
Type
Description
VID1 VID0 GNDA -5VIN / VT2 / PII2 -12VIN +12VIN +3.3VIN VCOREA VREF VT1 / PII1 VCC (+5V)
14 15 16 17
IN t IN t AGROUND AIN
Voltage Supply readouts from Pentium IITM. Voltage Supply readouts from Pentium IITM. Internally connected to all analog circuitry. The ground reference for all analog inputs. 0V to 4.096V FSR Analog Inputs (Default). / Thermistor 2 terminal input. Pentium II
TM
This multi-functional pin is programmable. 18 19 20 21 22 23 24 AIN AIN AIN AIN AOUT AIN POWER 0V to 4.096V FSR Analog Inputs. 0V to 4.096V FSR Analog Inputs. 0V to 4.096V FSR Analog Inputs. 0V to 4.096V FSR Analog Inputs. Reference Voltage. Thermistor 1 terminal input. / Pentium IITM thermal diode 1 input. +5V VCC power. Bypass with the parallel combination of 10F (electrolytic or tantalum) and 0.1F (ceramic) bypass capacitors.
-5-
W83783S
Preliminary
6. FUNCTIONAL DESCRIPTION
6.1 General Description
The W83783S provides at most 6 analog positive inputs, 3 fan speed monitors, 2 sets for fan PWM (Pulse Width Modulation) control, 2 thermal inputs from remote thermistors or 2N3904 transistors or PentiumTM II (Deschutes) thermal diode outputs and beep function output when the monitor value exceed the set limit value including voltage, temperature, or fan counter. When start the monitor function on the chip, the watch dog machine monitor every function and store the value to registers. If the monitor value exceeds the limit value, the interrupt status will be set to 1.
6.2.1 The first serial bus access timing are shown as follow: (a) Serial bus write to internal address register followed by the data byte
0 SCL SDA
Start By Master
R/W
Ack by 781D
D7
D6
D5
D4
D3
D2
D1
D0
Ack by 781D
Ack by 781D
Stop by Master
Figure 1. Serial Bus Write to Internal Address Register followed by the Data Byte
-6-
W83783S
Preliminary
(b) Serial bus write to internal address register only
0 SCL SDA
Start By Master
R/W
Ack by 781D
D7
D6
D5
D4
D3
D2
D1
D0
Ack by 781D Stop by Master
(c) Serial bus read from a register with the internal address register prefer to desired location
0 SCL SDA
Start By Master
R/W
Ack by 781D
D7
D6
D5
D4
D3
D2
D1
D0
Ack by Master Stop by Master
6.2.2 The serial bus timing of the temperature 2 and 3 is shown as follow: (a) Typical 2-byte read from preset pointer location (Temp, TOS, THYST)
0 SCL SDA
Start By Master
R/W
Ack by 782D
D7
... ...
D1
D0
Ack by Master
D7
... ...
D1
D0
Ack by Master Stop by Master
-7-
W83783S
Preliminary
(b) Typical pointer set followed by immediate read for 2-byte register (Temp, TOS, THYST)
0 SCL SDA
Start By Master
A2
A1
A0
R/W
Ack by 782D
D1
D0
Ack by 782D
0 SCL SDA
Start By Master
A2
A1
A0
R/W
Ack by 782D
D7
... ...
D1
D0
Ack by Master
D7
... ...
D1
D0
No Ack by Master Stop by Master
Figure 5. Typical Pointer Set Followed by Immediate Read for 2-Byte Register
(c) Typical read 1-byte from configuration register with preset pointer
0 SCL SDA
Start By Master
A2
A1
A0
R/W
Ack by 782D
D7
D6
D5
D4
D3
D2
D1
D0
No Ack by Master Stop by Master
-8-
W83783S
Preliminary
(d) Typical pointer set followed by immediate read from configuration register
0 SCL SDA
Start By Master
8 ...
A2
A1
A0
R/W
Ack by 782D
D1
D0
Ack by 782D
...
A2
A1
A0
R/W
Ack by 782D
D7
D6
D5
D4
D3
D2
D1
D0
No Ack by Master Stop by Master
Figure 7. Typical Pointor Set Followed by Immediate Read from Temp 2/3 Configuration Register
A2
A1
A0
R/W
0
Ack by 782D
D1
D0
Ack by 782D
D0
Ack by 782D Stop by Master
-9-
W83783S
Preliminary
(f) Temperature 2/3 TOS and THYST write
0 SCL SDA
Start By Master
A2
A1
A0
R/W
Ack by 782D
D1
D0
Ack by 782D
D0
Ack by 781D
D7
D6
D5
D4
D3
D2
D1
D0
Ack by 782D Stop by Master
- 10 -
W83783S
Preliminary
Pin 21 Pin 20 Pin 24
Positive Inputs
R1 V1 R2
12VIN
Positive Input
R5 V3 Negative Input V4 R7
N12VIN N5VIN
Pin 18 Pin 17
R8 R 10K, 1%
R6
VREF VT1
Pin 22 Pin 23
Typical Thermister Connection R THM 10K, 25 C **The connections of VT2 is same as VT1
Figure 11.
6.3.1 Monitor over 4.096V voltage: The input voltage +12VIN can be expressed as following equation.
12 VIN = V1
R2 R1 + R 2
The value of R1 and R2 can be selected to 28K Ohms and 10K Ohms, respectively, when the input voltage V1 is 12V. The node voltage of +12VIN can be subject to less than 4.096V for the maximun input range of the 8-bit ADC. The Pin 24 is connected to the power supply VCC with +5V. There are two functions in this pin with 5V. The first function is to supply internal analog power in the W83783S and the second function is that this voltage with 5V is connected to internal serial resistors to monitor the +5V voltage. The value of two serial resistors are 34K ohms and 50K ohms so that input voltage to ADC is 2.98V which is less than 4.096V of ADC maximum input voltage. The express equation can represent as follows.
Vin = V C C
50 K 50 K + 34 K
2 .98V
- 11 -
W83783S
Preliminary
6.3.2 Monitor negative voltage: The negative voltage should be connected two series resistors and a positive voltage VREF (is equal to 3.6V). In the Figure 11, the voltage V3 and V4 are two negative voltage which they are -12V and 5V respectively. The voltage V3 is connected to two serial resistors then is connected to another terminal VREF which is positive voltage. So as that the voltage node N12VIN can be obtain a posedge voltage if the scales of the two serial resirtors are carefully selected. It is recommanded from Winbond that the scale of two serial resistors are R5=232K ohms and R6=56K ohm. the The input voltage of node -12VIN can be calculated by following equation.
N 12 VIN = ( VREF + V5 ) (
232 K 232 K + 56 K
) + V5
where VREF is equal 3.6V. If the V5 is equal to -12V then the voltage is equal to 0.567V and the converted hexdecimal data is set to 35h by the 8-bit ADC with 16mV-LSB.This monitored value should be converted to the real negative votage and the express equation is shown as follows.
V5 =
N 12 VIN VREF 1
Where is 232K/(232K+56K). If the N2VIN is 0.567 then the V5 is approximately equal to -12V. The another negative voltage input V6 (approximate -5V) also can be evaluated by the similar method and the serial resistors can be selected with R7=120K ohms and R8=56K ohms by the Winbond recommended. The expression equation of V6 With -5V voltage is shown as follows.
V6 =
N 5 VIN VREF 1
Where the is set to 120K/(120K+56K). If the monitored ADC value in the N5VIN channel is 0.8635, VREF=3.6V and the parameter is 0.6818 then the negative voltage of V6 can be evalated to be 5V.
- 12 -
W83783S
Preliminary
6.3.3 Monitor temperature from thermistor: The W83783S can connect three thermistors to measure three different envirment temperature. The specification of thermistor should be considered to (1) value is 3435K, (2) resistor value is 10K ohms at 25C. In the Figure 11, the themistor is connected by a serial resistor with 10K Ohms, then connect to VREF (Pin 37).
6.3.4 Monitor temperature from Pentium IITM thermal diode or bipolar transistor 2N3904 The W83783S can alternate the thermistor to Pentium IITM (Deschutes) thermal diode interface or transistor 2N3904 and the circuit connection is shown as Figure 12. The pin of Pentium IITM D- is connected to power supply ground (GND) and the pin D+ is connected to pin PIIx in the W83783S. The resistor R=30K ohms should be connected to VREF to supply the diode bias current and the bypass capacitor C=3300pF should be added to filter the high frequency noise. The transistor 2N3904 should be connected to a form with a diode, that is, the Base (B) and Collector (C) in the 2N3904 should be tied togeter to act as a thermal diode.
VREF R=30K, 1% Bipolar Transistor Temperature Sensor PIITDx C=3300pF B C 2N3904 E R=30K, 1%
W83783S
OR
Pentium II CPU Therminal Diode DD+ PIITDx C=3300pF
Figure 12.
- 13 -
W83783S
Preliminary
6.4 FAN Speed Count and FAN Speed Control
6.4.1 Fan speed count Inputs are provides for signals from fans equipped with tachometer outputs. The level of these signals should be set to TTL level, and maximum input voltage can not be over +5.5V. If the input signals from the tachometer outputs are over the VCC, the external trimming circuit should be added to reduce the voltage to obtain the input specification. The normal circuit and trimming circuits are shown as Figure 13. Determine the fan counter according to: Count = 135 . 10 6 RPM Divisor
In other words, the fan speed counter has been read from register CR28 or CR29 or CR2A, the fan speed can be evaluated by the following equation.
RPM =
1.35 10
Count Divisor
The default divisor is 2 and defined at CR47.bit7~4, CR4B.bit7~6, and Bank0 CR5D.bit5~7 which are three bits for divisor. That provides very low speed fan counter such as power supply fan. The followed table is an example for the relation of divisor, PRM, and count.
Time per Revolution 6.82 ms 13.64 ms 27.27 ms 54.54 ms 109.08 ms 218.16 ms 436.32 ms 872.64 ms Table 1.
Time for 70% 9.74 ms 19.48 ms 38.96 ms 77.92 ms 155.84 ms 311.68 ms 623.36 ms 1246.72 ms
- 14 -
W83783S
Preliminary
+12V +5V +12V
Pull-up resister diode +12V FAN Out GND Fan Input Pin 18/19/20 4.7K Ohms diode +12V
FAN Connector
W83783S
FAN Connector
10K
W83783S
Figure 13-2. Fan with Tach Pull-Up to +12V, or Totem-Pole Output and Register Attenuator
+12V
+12V
diode
FAN Connector
W83783S
FAN Connector Figure 13-4. Fan with Tach Pull-Up to +12V, or Totem-Pole Putput and Zener Clamp
W83783S
Figure 13-3. Fan with Tach Pull-Up to +12V and Zener Clamp
6.4.2 Fan speed control The W83783S provides four sets for fan PWM speed control. The duty cycle of PWM can be programmed by a 8-bit registers which are defined in the Bank0 CR5A and CR5B. The default duty cycle is set to 100%, that is, the default 8-bit registers is set to FFh. The expression of duty can be represented as follows.
Duty cycle (% ) =
100%
The PWM clock frequency also can be program and defined in the Bank0.CR5C . The application circuit is shown as follows.
- 15 -
W83783S
Preliminary
+12V
Figure 14.
Temperature
8-Bit Digital Output 8-Bit Binary 8-Bit Hex 7Dh 19h 01h 00h FFh E7h C9h Table 2.
9-Bit Digital Output 9-Bit Binary 0,1111,1010 0,0011,0010 0,0000,0010 0,0000,0001 0,0000,0000 1,1111,1111 1,1111,1110 1,1100,1110 1,1001,0010 9-Bit Hex 0FAh 032h 002h 001h 000h 1FFh 1FFh 1CEh 192h
- 16 -
W83783S
Preliminary
6.5.1 The W83783S temperature sensor 2 SMI# interrupt has two modes: (1) Comparator Interrupt Mode Setting the THYST (Temperature Hysteresis) limit to 127C will set temperature sensor 1 SMI# to the Comparator Interrupt Mode. Temperature exceeds TO (Over Temperature) Limit causes an interrupt and this interrupt will be reset by reading all the Interrupt Status Register. Once an interrupt event has occurred by exceeding TO, then reset, if the temperature remains above the TO , the interrupt will occur again when the next conversion has completed. If an interrupt event has occurred by exceeding TO and not reset, the interrupts will not occur again. The interrupts will continue to occur in this manner until the temperature goes below TO. (Figure 15-1 ) (2) Two-Times Interrupt Mode Setting the THYST lower than TO will set temperature sensor 1 SMI# to the Two-Times Interrupt Mode. Temperature exceeding TO causes an interrupt and then temperature going below THYST will also cause an interrupt if the previous interrupt has been reset by reading all the interrupt Status Register. Once an interrupt event has occurred by exceeding TO , then reset, if the temperature remains above the THYST , the interrupt will not occur. (Figure 15-2 )
T HYST 127'C
T OI
T OI
T HYST
SMI#
SMI#
- 17 -
W83783S
Preliminary
6.5.2 The W83783S temperature sensor 1 SMI# interrupt has three modes (1) Comparator Interrupt Mode Temperature exceeding TO causes an interrupt and this interrupt will be reset by reading all the Interrupt Status Register. Once an interrupt event has occurred by exceeding TO, then reset, if the temperature remains above the THYST, the interrupt will occur again when the next conversion has completed. If an interrupt event has occurred by exceeding TO and not reset, the interrupts will not occur again. The interrupts will continue to occur in this manner until the temperature goes below THYST. ( Figure 16-1 ) (2) Two-Times Interrupt Mode Temperature exceeding TO causes an interrupt and then temperature going below THYST will also cause an interrupt if the previous interrupt has been reset by reading all the interrupt Status Register. Once an interrupt event has occurred by exceeding TO , then reset, if the temperature remains above the THYST , the interrupt will not occur. (Figure 16-2 ) (3) One-Time Interrupt Mode Temperature exceeding TO causes an interrupt and then temperature going below THYST will not cause an interrupt. Once an interrupt event has occurred by exceeding TO , then going below THYST, an interrupt will not occur again until the temperature exceeding TO. (Figure 16-3 )
T OI
T OI
T HYST
T HYST
SMI#
SMI#
- 18 -
W83783S
Preliminary
T OI
T HYST
SMI#
6.5.3 The W83783S temperature sensor 1 Over-Temperature (OVT#) has three modes (1) Comparator Mode : Setting Bank1 CR[52h] bit 2 to 0 will set OVT# signal to comparator mode. Temperature exceeding TO causes the OVT# output activated until the temperature is less than THYST. ( Figure 17) (2) Interrupt Mode: Setting Bank1 CR[52h] bit 2 to 1 will set OVT# signal to interrupt mode. Setting Temperature exceeding TO causes the OVT# output activated indefinitely until reset by reading temperature sensor 2 or sensor 3 registers. Temperature exceeding TO , then OVT# reset, and then temperature going below THYST will also cause the OVT# activated indefinitely until reset by reading temperature sensor2 or sensor 3 registers. Once the OVT# is activated by exceeding TO , then reset, if the temperature remains above THYST , the OVT# will not be activated again.( Figure 17)
- 19 -
W83783S
Preliminary
To
T HYST
OVT#
(Comparator Mode; default)
OVT#
(Interrupt Mode)
- 20 -
W83783S
Preliminary
High limit
Low limit
SMI#
SMI#
- 21 -
W83783S
Preliminary
7. REGISTERS AND RAM
7.1 Configuration Register Index 40h
Register Location: Power on Default Value Attribute: Size:
7 6 5
Bit 7: A one restores power on default value to all registers except the Serial Bus Address register. This bit clears itself since the power on default is zero. Bit 6: The logical 1 in this bit drives a zero on BEEP/GPO# pin. Bit 5: Reserved Bit 4: Reserved Bit 3: A one disables the SMI# output without affecting the contents of Interrupt Status The device will stop monitoring. It will resume upon clearing of this bit. Bit 2: Reserved Bit 1: A one enables the SMI# Interrupt output. Bit 0: A one enables startup of monitoring operations, a zero puts the part in standby mode. Registers.
Note: The outputs of Interrupt pins will not be cleared if the user writes a zero to this location after an interrupt has occurred unlike "INT_Clear'' bit.
- 22 -
W83783S
Preliminary
7.2 Interrupt Status Register 1 Index 41h
Register Location: Power on Default Value Attribute: Size:
7
Bit 7: A one indicates the fan count limit of FAN2 has been exceeded. Bit 6: A one indicates the fan count limit of FAN1 has been exceeded. Bit 5: A one indicates a High limit of VT1 has been exceeded from temperature sensor. Bit 4: A one indicates a High limit of VT2 has been exceeded from temperature sensor . Bit 3: A one indicates a High or Low limit of +5VIN has been exceeded. Bit 2: A one indicates a High or Low limit of +3.3VIN has been exceeded. Bit 1: Reserved. Bit 0: A one indicates a High or Low limit of VCORE has been exceeded.
- 23 -
W83783S
Preliminary
7 6 5 4 3 2 1 0
Bit 7-4:Reserved.This bit should be set to 0. Bit 3: A one indicates the fan count limit of FAN3 has been exceeded. Bit 2: A one indicates a High or Low limit of -5VIN has been exceeded. Bit 1: A one indicates a High or Low limit of -12VIN has been exceeded. Bit 0: A one indicates a High or Low limit of +12VIN has been exceeded.
Bit 7-0: A one disables the corresponding interrupt status bit for SMI interrupt.
- 24 -
W83783S
Preliminary
7.5 SMI# Mask Register 2 Index 44h
Register Location: Power on Default Value Attribute: Size:
7 6
Bit 7-4: Reserved. This bit should be set to 0. Bit 3-0: A one disables the corresponding interrupt status bit for SMI interrupt.
- 25 -
W83783S
Preliminary
7.7 VID/Fan Divisor Register Index 47h
Register Location: Attribute: Size: 47h Read/Write 8 bits
7 6 5 4 3 2 1 0
Bit 7-6: FAN2 Speed Control. Bit 5-4: FAN1 Speed Control. Bit 3-0: The VID <3:0> inputs
Note : Please refer to Bank0 CR[5Dh] , Fan divisor table.
Reserved
Bit 7: Read Only - Reserved. Bit 6-0: Read/Write - Serial Bus address <6:0>.
- 26 -
W83783S
Preliminary
7.9 Value RAM Index 20h- 3Fh or 60h - 7Fh
Index 20h or 60h 21h or 61h 22h or 62h 23h or 63h 24h or 64h 25h or 65h 26h or 66h 27h or 67h 28h or 68h VCORE reading Reserved +3.3VIN reading +5VIN reading +12VIN reading -12VIN reading -5VIN reading
Description
Temperature sensor 2 (VT2) reading FAN1 reading Note: This location stores the number of counts of the internal clock per revolution.
29h or 69h
FAN2 reading Note: This location stores the number of counts of the internal clock per revolution.
2Ah or 6Ah
FAN3 reading Note: This location stores the number of counts of the internal clock per revolution.
2Bh or 6Bh 2Ch or 6Ch 2Dh or 6Dh 2Eh or 6Eh 2Fh or 6Fh 30h or 70h 31h or 71h 32h or 72h
VCORE High Limit, default value is defined by Vcore Voltage +0.2v. VCORE Low Limit, default value is defined by Vcore Voltage -0.2v. Reserved Reserved +3.3VIN High Limit +3.3VIN Low Limit +5VIN High Limit +5VIN Low Limit
- 27 -
W83783S
Preliminary
7.12 Value RAM Index 20h- 3Fh or 60h - 7Fh, continued Address A6-A0 33h or 73h 34h or 74h 35h or 75h 36h or 76h 37h or 77h 38h or 78h 39h or 79h 3Ah or 7Ah 3Bh or 7Bh +12VIN High Limit +12VIN Low Limit -12VIN High Limit -12VIN Low Limit -5VIN High Limit -5VIN Low Limit Temperature sensor 2 (VT2) High Limit Temperature sensor 2 (VT2) Hysteresis Limit FAN1 Fan Count Limit Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. 3Ch or 7Ch FAN2 Fan Count Limit Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. 3Dh or 7Dh FAN3 Fan Count Limit Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. 3E- 3Fh or 7E-7Fh Reserved Description
Setting all ones to the high limits for voltages and fans (0111 1111 binary for temperature) means interrupts will never be generated except the case when voltages go below the low limits.
- 28 -
W83783S
Preliminary
7.10 Voltage ID (VID4) & Device ID - Index 49h
Register Location: Power on Default Value Size:
7
VID4
DID<6:0>
Bit 7-1: Read Only - Device ID<6:0> Bit 0 : Read/Write - The VID4 inputs.
- 29 -
W83783S
Preliminary
Bit 7-4 : Reserved Bit 3: Set to 1, disable temperature Sensor 1 and can not access any data from Temperature Sensor 1. Bit 2-0: Temperature 2 Serial Bus Address. The serial bus address is 1001xxx. Where xxx are defined in these bits.
Bit 7-6:Fan3 speed divisor. Please refer to Bank0 CR[5Dh] , Fan divisor table. Bit 5-4: Select A/D Converter Clock Input. <5:4> = 00 - default. ADC clock select 22.5 Khz. <5:4> = 01- ADC clock select 5.6 Khz. (22.5K/4) <5:4> = 10 - ADC clock select 1.4Khz. (22.5K/16) <5:4> = 11 - ADC clock select 0.35 Khz. (22.5K/64)
- 30 -
W83783S
Preliminary
Bit 3-2: Clock Input Select. <3:2> = 00 - Pin 3 (CLKIN) select 14.318M Hz clock. <3:2> = 01 - Default. Pin 3 (CLKIN) select 24M Hz clock. <3:2> = 10 - Pin 3 (CLKIN) select 48M Hz clock . <3:2> = 11 - Reserved. Pin3 no clock input. Bit 1-0: Reserved. User defined.
Bit 7: Set to 1 , select pin 9 SMI#/PWMOUT2 as PWM output. Set to 0, select pin 9 as SMI# output. Bit6: Set to 1, the SMI# output type of temperature sensor 1 is set to Comparator Interrupt mode. Set to 0, the SMI# output type is set to Interrupt mode (defined by CR[4Ch] Bit 5 ). Bit 5: Set to 1, the SMI# output type of temperature sensor 1 is set to One-Time interrupt mode. Set to 0, the SMI# output type of temperature sensor 1 is set to Two-Times interrupt mode. Bit 4 : Reserved. User Defined. Bit 3: Disable temperature sensor 1 over-temperature (OVT) output if set to 1. Default 0, enable OVT1 output through pin OVT#. Bit 2: Over-temperature polarity. Write 1, OVT# active high. Write 0, OVT# active low. Default 0. Bit 1-0: Reserved. User Defined.
- 31 -
W83783S
Preliminary
7.14 FAN IN/OUT and BEEP/GPO# Control Register - Index 4Dh
Register Location: Power on Default Value Attribute: Size:
7 6
Bit 7: Disable power-on abnormal the monitor voltage including V-Core A and +3.3V. If these voltage exceed the limit value, the pin (Open Drain) of BEEP will drives 300Hz and 600Hz frequency signal. Write 1, the frequency will be disable. Default 0. After power on, the system should set 1 to this bit to 1 in order to disable BEEP. Bit 6: BEEP/GPO# Pin Function Select. Write 1 Select GPO# function. Set 0, select BEEP function. This bit default 0. Bit 5: FAN 3 output value if FANINC3 sets to 0. Write 1, then pin 4 always generate logic high signal. Write 0, pin 4 always generates logic low signal. This bit default 0. Bit 4: FAN 3 Input Control. Set to 1, pin 4 acts as FAN clock input, which is default value. Set to 0, this pin 4 acts as FAN control signal and the output value of FAN control is set by this register bit 5. This output pin can connect to power PMOS gate to control FAN ON/OFF. Bit 3: FAN 2 output value if FANINC2 sets to 0. Write 1, then pin 3 always generate logic high signal. Write 0, pin 3 always generates logic low signal. This bit default 0. Bit 2: FAN 2 Input Control. Set to 1, pin 3 acts as FAN clock input, which is default value. Set to 0, this pin 3 acts as FAN control signal and the output value of FAN control is set by this register bit 3. This output pin can connect to power NMOS gate to control FAN ON/OFF. Bit 1: FAN 1 output value if FANINC1 sets to 0. Write 1, then pin 2 always generate logic high signal. Write 0, pin 2 always generates logic low signal. This bit default 0. Bit 0: FAN 1 Input Control. Set to 1, pin 2 acts as FAN clock input, which is default value. Set to 0, this pin 2 acts as FAN control signal and the output value of FAN control is set by this register bit 1. This output pin can connect to power PMOS gate to control FAN ON/OFF.
- 32 -
W83783S
Preliminary
7.15 Register 50h ~ 5Fh Bank Select - Index 4Eh
Register Location: Power on Default Value Attribute: Size:
7 6
Bit 7: HBACS- High byte access. Set to 1, access Register 4Fh high byte register. Set to 0, access Register 4Fh low byte register. Default 1. Bit 6-3: Reserved. This bit should be set to 0. Bit 2-0: Index ports 0x50~0x5F Bank select.
VIDH
VIDL
Bit 15-8: Vendor ID High Byte if CR4E.bit7=1.Default 5Ch. Bit 7-0: Vendor ID Low Byte if CR4E.bit7=0. Default A3h.
- 33 -
W83783S
Preliminary
7.17 Winbond Test Register -- Index 50h - 55h (Bank 0)
Bit 7: Enable BEEP Output from FAN 2 if the monitor value exceed the limit value. Write 1, enable BEEP output, which is default value. Bit 6: Enable BEEP Output from FAN 1 if the monitor value exceed the limit value. Write 1, enable BEEP output, which is default value. Bit 5: Enable BEEP Output from Temperature Sensor 1 if the monitor value exceed the limit value. Write 1, enable BEEP output. Default 0 Bit 4: Enable BEEP output for Temperature Sensor 2 if the monitor value exceed the limit value. Write 1, enable BEEP output. Default 0 Bit 3: Enable BEEP output from VDD (+5V), Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. Bit 2: Enable BEEP output from +3.3V. Write 1, enable BEEP output, which is default value. Bit 1: Reserved. Bit 0: Enable BEEP Output from VCORE if the monitor value exceed the limits value. Write 1, enable BEEP output, which is default value
- 34 -
W83783S
Preliminary
7.19 BEEP Control Register 2-- Index 57h (Bank 0)
Register Location: Attribute: Size: 8 bits
7 6 5 4 3 2 1 0
57h Read/Write
Bit 7: Enable Global BEEP. Write 1, enable global BEEP output. Default 1. Write 0, disable all BEEP output. Bit 6-4: Reserved. Bit 3: Enable BEEP Output from FAN 3 if the monitor value exceed the limit value. Write 1, enable BEEP output. Default 0. Bit 2: Enable BEEP output from -5V, Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. Bit 1: Enable BEEP output from -12V, Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. Bit 0: Enable BEEP output from +12V, Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output.
- 35 -
W83783S
Preliminary
7.20 Chip ID -- Index 58h (Bank 0)
Register Location: Power on Default Value Attribute: Size:
7 6
CHIPID
Bit 7: Winbond Chip ID number. Read this register will return 40h.
59h <7>=0 and <6:4> = 111 and <3:0> = 0000 Read/Write 8 bits
5 4 3 2 1 0
Bit 7-6: Reserved Bit 5: Temperature sensor diode 1. Set to 1, select Pentium II compatible Diode. Set to 0 to select 2N3904
Bipolar mode.
Bit 4: Temperature sensor diode 2. Set to 1, select Pentium II compatible Diode. Set to 0 to select 2N3904
Bipolar mode.
- 36 -
W83783S
Preliminary
7.22 PWMOUT1 Control Register -- Index 5Ah (Bank 0)
Register Location: Power on default value: Attribute: Size:
7 6
PWM1_DUTY
Bit 7: PWMOUT1 duty cycle control Write FF, Duty cycle is 100%, Write 00, Duty cycle is 0%.
- 36-A -
W83783S
Preliminary
7.23 PWMOUT2 Control Register -- Index 5Bh (Bank 0)
Register Location: Power on default value: Attribute: Size:
7 6
PWM2_DUTY
Bit 7: PWMOUT2 duty cycle control Write FF, Duty cycle is 100%, Write 00, Duty cycle is 0%.
Bit 7: Reserved Bit 6-4: PWMOUT1 clock selection. The clock defined frequency is same as PWMOUT2 clock selection.
- 37 -
W83783S
Preliminary
Bit 3: Set to 1. Enable PWMOUT1 PWM Control Bit 2-0: PWMOUT2 clock Selection. <2:0> = 000: 46.87K Hz <2:0> = 001: 23.43K Hz (Default) <2:0> = 010: 11.72K Hz <2:0> = 011: 5.85K Hz <2:0> = 100: 2.93K Hz
Bit 7: Fan3 divisor Bit 2. Bit 6: Fan2 divisor Bit 2. Bit 5: Fan1 divisor Bit 2. Bit 4: Reserved Bit 3: Reserved Bit 2: Temperature sensor 1 select into thermal diode such as Pentium II CPU supported. Set to 1, select bipolar sensor. Set to 0, select thermistor sensor. Bit 1: Temperature Sensor 2 type selection. Defined as DIODES1 described in the bit 2. Bit 0: Reserved
- 38 -
W83783S
Preliminary
7.26 Reserved Register -- Index 5Eh (Bank 0)
TEMP2<8:1>
Reserved
TEMP2<0>
Bit 7: Temperature <0> of sensor2, which is low byte. Bit 6-0: Reserved. This bit should be set to 0.
- 39 -
W83783S
Preliminary
7.30 Temperature Sensor 1 Configuration Register - Index 01h
Register Location: Power on Default Value Size:
7 6
Bit 7-5: Read - Reserved. This bit should be set to 0. Bit 4-3: Read/Write - Number of faults to detect before setting OVT# output to avoid false tripping due to noise. Bit 2: Read - Reserved. This bit should be set to 0. Bit 1: Read/Write - OVT# Interrupt mode select. This bit default is set to 0, which is compared mode. When set to 1, interrupt mode will be selected. Bit 0: Read/Write - When set to 1 the sensor will stop monitor.
- 40 -
W83783S
Preliminary
7.31 Temperature Sensor 1 Hysteresis (High Byte) Register - Index 02h
Register Location: Power on Default Value Attribute: Size:
7 6
THYST2<8:1>
Bit 7-0: Temperature hysteresis bit 8-1, which is High Byte. The temperature default 75 degree C.
Reserved
THYST2<0>
Bit 7: Temperature hysteresis bit 0, which is low Byte. Bit 6-0: Reserved. This bit should be set to 0.
- 41 -
W83783S
Preliminary
7.33 Temperature Sensor 1 Over-temperature (High Byte) Register - Index 03h
Register Location: Power on Default Value Attribute: Size:
7 6
TOVF2<8:1>
Bit 7-0: Over-temperature bit 8-1, which is High Byte. The temperature default 80 degree C.
Reserved
TOVF2<0>
Bit 7: Read/Write - Over-temperature bit 0, which is low Byte. Bit 6-0: Read Only - Reserved. This bit should be set to 0.
- 42 -
W83783S
Preliminary
7.35 Reserved Register -- Index 50h--52h (BANK4) 7.36 BEEP Control Register 3 -- Index 53h (Bank 4)
Register Location: Power on Default Value Attribute: Size:
7
Bit 7-6: Reserved. Bit 5: User define BEEP output function. Write 1, the BEEP is always active. Write 0, this function is inactive. (Default 0) Bit 4-0: Reserved.
7.37 Reserved Register -- Index 54h--58h (Bank 4) 7.38 Real Time Hardware Status Register I -- Index 59h (Bank 4)
Register Location: Power on Default Value Attribute: Size:
7 6
- 43 -
W83783S
Preliminary
Bit 7: FAN 2 Status. Set 1, the fan speed counter is over the limit value. Set 0, the fan speed counter is in the limit range. Bit 6: FAN 1 Status. Set 1, the fan speed counter is over the limit value. Set 0, the fan speed counter is in the limit range. Bit 5: Temperature sensor 1 Status. Set 1, the voltage of temperature sensor is over the limit value. Set 0, the voltage of temperature sensor is in the limit range. Bit 4: Temperature sensor 2 Status. Set 1, the voltage of temperature sensor is over the limit value. Set 0, the voltage of temperature sensor is in the limit range. Bit 3: +5V Voltage Status. Set 1, the voltage of +5V is over the limit value. Set 0, the voltage of +5V is in the limit range. Bit 2: +3.3V Voltage Status. Set 1, the voltage of +3.3V is over the limit value. Set 0, the voltage of +3.3V is in the limit range. Bit 1: Reserved. Bit 0: VCORE Voltage Status. Set 1, the voltage of VCORE is over the limit value. Set 0, the voltage of VCORE is in the limit range.
- 44 -
W83783S
Preliminary
Bit 7-4: Reserved Bit 3: FAN3 Voltage Status. Set 1, the fan speed counter is over the limit value. Set 0, the fan speed counter is during the limit range. Bit 2: -5V Voltage Status. Set 1, the voltage of -5V is over the limit value. Set 0, the voltage of -5V is during the limit range. Bit 1: -12V Voltage Status. Set 1, the voltage of -12V is over the limit value. Set 0, the voltage of 12V is during the limit range. Bit 0: +12V Voltage Status. Set 1, the voltage of +12V is over the limit value. Set 0, the voltage of +12V is in the limit range.
- 45 -
W83783S
Preliminary
8. SPECIFICATIONS
8.1 Absolute Maximum Ratings
PARAMETER Power Supply Voltage Input Voltage Operating Temperature Storage Temperature RATING -0.5 to 7.0 -0.5 to VDD+0.5 0 to +70 -55 to +150 UNIT V V C C
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device.
8.2 DC Characteristics
(Ta = 0 C to 70 C, VDD = 5V 10%, VSS = 0V) PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
I/O12t - TTL level bi-directional pin with source-sink capability of 12 mA Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Input High Leakage Input Low Leakage VIL VIH VOL VOH ILIH ILIL 2.4 +10 -10 2.0 0.4 0.8 V V V V A A IOL = 12 mA IOH = - 12 mA VIN = VDD VIN = 0V
I/O12ts - TTL level bi-directional pin with source-sink capability of 12 mA and schmitt-trigger level input Input Low Threshold Voltage Input High Threshold Voltage Hysteresis Output Low Voltage Output High Voltage Input High Leakage Input Low Leakage VtVt+ VTH VOL VOH ILIH ILIL 2.4 +10 -10 0.5 1.6 0.5 0.8 2.0 1.2 0.4 1.1 2.4 V V V V V A A VDD = 5 V VDD = 5 V VDD = 5 V IOL = 12 mA IOH = - 12 mA VIN = VDD VIN = 0V
- 46 -
W83783S
Preliminary
8.2 DC Characteristics, continued
PARAMETER
SYM.
MIN.
TYP.
MAX.
UNIT
CONDITIONS
OUT12t - TTL level output pin with source-sink capability of 12 mA Output Low Voltage Output High Voltage VOL VOH 2.4 0.4 V V IOL = 12 mA IOH = -12 mA
OD8 - Open-drain output pin with sink capability of 8 mA Output Low Voltage VOL 0.4 V IOL = 8 mA OD12 - Open-drain output pin with sink capability of 12 mA Output Low Voltage VOL 0.4 V IOL = 12 mA OD48 - Open-drain output pin with sink capability of 48 mA Output Low Voltage VOL 0.4 V IOL = 48 mA INt - TTL level input pin Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage INts VIL VIH ILIH ILIL 2.0 +10 -10 0.8 V V A A 1.1 2.4 +10 -10 VIN = VDD VIN = 0 V
- TTL level Schmitt-triggered input pin VtVt+ VTH ILIH ILIL 0.5 1.6 0.5 0.8 2.0 1.2 V V V A A VDD = 5 V VDD = 5 V VDD = 5 V VIN = VDD VIN = 0 V
Input Low Threshold Voltage Input High Threshold Voltage Hysteresis Input High Leakage Input Low Leakage
- 47 -
W83783S
Preliminary
8.3 AC Characteristics 8.3.1 Serial Bus Timing Diagram
SCL
SCL
t HD;SDA
t t HD;DAT SU;STO
SDA IN
VALID DATA
t SU;DAT
SDA OUT
Serial Bus Timing PARAMETER SCL clock period Start condition hold time Stop condition setup-up time DATA to SCL setup time DATA to SCL hold time SCL and SDA rise time SCL and SDA fall time SYMBOL t SCL tHD;SDA tSU;STO tSU;DAT tHD;DAT tR tF
-
MAX.
UNIT uS uS uS nS nS
1.0 300
uS nS
- 48 -
W83783S
Preliminary
9. HOW TO READ THE TOP MARKING
The top marking of W83783S
- 49 -
W83783S
Preliminary
10. PACKAGE DIMENTIONS
(24-pin SOP)
24 13
Control demensions are in milmeters .
12
Headquarters
No. 4, Creation Rd. III Science-Based Industrial Park Hsinchu, Taiwan TEL: 886-35-770066 FAX: 886-35-789467 www: http://www.winbond.com.tw/
Taipei Office
11F, No. 115, Sec. 3, Min-Sheng East Rd. Taipei, Taiwan TEL: 886-2-7190505 FAX: 886-2-7197502 TLX: 16485 WINTPE
Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this data sheet belong to their respective owners. These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sale.
Publication Release Date: April 1999 Revision 0.55
- 50 -
R10
-12V
56K 1% VREF U1 3VCC R7 R 4.7K THRM# TO PIIX4 R8 R 4.7K OVT# VID4 FANIN1 FANIN2 PWMOUT1 OVT# BEEP/GPO# VID3 CLKIN SMI# SCL SDA 3VCC R5 R 4.7K 0 SMDAT SMCLK R3 R 0 VREF R31 30K 1% PIID+ PIIDR R6 R 4.7K W83783S VREF 1 2 3 4 5 6 7 8 9 10 11 12 VID4 FANIN1 FANIN2 FANIN3/PWMOUT1 OVT# BEEP/GPO# VID3 CLKIN SMI#/PWMOUT2 GNDD SCL SDA VCC VT1/PII1 VREF VCORE +3.3VIN +12VIN -12VIN -5VIN/VT2/PII2 GNDA VID0 VID1 VID2 24 23 22 21 20 19 18 17 16 15 14 13 R32 VT1/PII1 VREF VCORE +3.3VIN +12VIN -12VIN -5VIN GNDA VID0 VID1 VID2 R
-5V
56K 1%
{
SDA SCL
EXTSMI#
SMI#
R R4
10K 1% GNDA
Note:
+12V
JP2
Q2 3906
PWMOUT1
R21
510
Q3 MOSFET N 2N7002
C3 47u
JP1 +
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.