Professional Documents
Culture Documents
1. 3D Touch Set Up and Operations Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 2. How this manual works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 3. Manual symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 4. Process overview... how the 3D Touch works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 5. Print material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 6. Pre-print checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.1 a. Clearing the print bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.2 b. Check the print bed is fitted correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.3 c. Power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.4 d. Test all axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.5 e. Check the hot-end nozzles are clean from plastic debris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.6 f. Check the print bed is level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.7 g. Check the bed is referenced to the extruder nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.8 h. Load the extruders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.9 i. Extruder control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.10 j. Purge the extruder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.11 k. How to start a print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6.12 l. Print a successful raft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 7. Print the first model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 8. Essential post-print operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8.1 b. Check print bed flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8.2 c. Empty the waste bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8.3 a. Print removal and post-processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 9. Further printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10 10. Further operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.1 c. Setting the extruder pressure bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.2 b. Reloading the extruders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.3 d. Control panel functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.4 a. Power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.5 e. Upgrading your printer firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.6 f. Adjusting the nozzle wipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.7 g. Fine adjustment to level the nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.8 h. Handling a ground-out filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10.9 i. Handling snapped filament in the delivery tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.11 11. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.12 12. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13 13. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 BFB-Touch Set Up and Operations Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 6 7 8 9 15 17 18 21 23 24 25 26 30 32 37 38 39 40 44 45 46 47 48 50 51 52 54 55 59 60 61 62 64 66 71 72 73 74 75
Page 2
3D Touch
Welcome to the 3D Touch Setup and Operations Manual. This manual is designed to get you up and running as quickly as possible. It can be read either on-line or off-line (see below).
Requirements
To complete the exercises in this manual the user will need: All the items included in the 3D Touch box. Items should be unpacked. Unpacking instructions (which should be included in the top of the box) can be downloaded here. The setup print files: The print files required are already included on the USB memory stick supplied in your toolkit. If you do not have these files you can download them by clicking on the icon on the left. After downloading: Unpack the files to the root of your USB stick. The printer can only see uncompressed files at the root of the USB stick i.e. do not put them inside a folder.
Page 3
3D Touch
You can start reading the manual by clicking the links on the navigation bar at the left of the screen:
Off-line reading
Simply click on the "Export this space" button at the top left of the screen to export the manual to a PDF. Follow the on screen instructions.
Page 4
3D Touch
If you have a slow internet connection, it is possible to select individual sections of the manual to export, making it possile to download small sections at a time. Simply tick the boxes next to the sections you need. Alternatively, if bandwidth is not an issue, select all.
Page 5
3D Touch
1. Introduction
Thank you for purchasing your 3D Touch. Before first use, the 3D Touch needs careful setting up. The list below illustrates some of the essential operations which must be carried out before operation: Make sure the bed is clear of any build material Check the bed is fitted correctly Check the hot-end nozzles are clean from plastic debris Check the bed is level Check the bed is referenced to the extruder nozzles Load the extruders correctly Print a successful raft Failure to carry out all of the set-up procedures contained in this document will damage the machine.
This document has been designed to illustrate the essential procedures and get you up and running as quickly as possible. Please take time to understand how the process works and complete each procedure in the order set out in this manual. Setting up can take from 20-60 minutes depending on the skill level of the operator. Support is available by raising a ticket at www.bitsfrombytes.com We welcome any feedback you may have, and wish you well in your 3D printing!
Page 6
3D Touch
Page 7
3D Touch
3. Manual symbols
Page 8
3D Touch
3D Touch
Tool kit
The image below identifies the tools included in the tool kit.
Page 9
3D Touch
Creating a 3D model
The images below illustrate the process of creating a 3D model.
Page 10
3D Touch
Note 1: Most CAD packages export to STL format. However, STL quality depends on the CAD package. Poor quality STLs may need repairing before loading into "Axon". STL fixing programs are readily available (e.g. NetFabb).
Page 11
3D Touch
Page 12
3D Touch
The extruders pull filament from the reel via the delivery tubes and drive through a hot-end to produce a thin molten filament of plastic. The extruder draws each layer with this filament. After each layer is produced the bed increments down so that a new layer can be drawn on top of the last, building up the 3D model.
Overhanging features
Page 13
3D Touch
A second (optional) extruder can print support filament for printing overhanging-features. This support structure can be automatically generated in Axon if desired.
Page 14
3D Touch
5. Print material
We support two print materials: PLA and ABS. Both have different properties and can be used in different build/support combinations. Typically, PLA performs well as a build material with an ABS raft, and (if needed) ABS support.
PLA
PLA is a hard plastic with a low environmental impact. It is not a petrochemical - it is derived from renewable resources, such as starch. It is a relatively new plastic and has excellent print characteristics. As a build material: As a support material: Good for large and small prints. Stable for 20 years up to 50 degrees Celsius Supports ABS well as it peels away easily. May be dissolved if required (see below).
PLA support can be dissolved by: 1. Leaving the model in an ultra-sonic support removal tank with water and caustic soda. Time and concentration depends on the volume of the material needed to dissolve. 2. Leave the model in water at 80C for over 48 hours. The support removal tank also provides this functionality.
ABS
ABS is a well-known plastic with excellent toughness characteristics. As a build material: As a support material: Good for small prints with high toughness requirements. Do not print area larger than 100 mm square ABS has relatively high shrinkage on cooling, and some geometries for larger prints are prone to warping. Supports PLA well as it peels away easily.
Material storage
All polymers degrade with time. The following conditions ensure the filament remains high quality: Do not unpack until filament is needed. Store at room temperature: 15-20 C. Keep away from UV light (e.g. sunlight).
Page 15
3D Touch
If machine is to left unused for an extended period of time, repack filament with silica-gel sachet to maintain dryness (if present). Use within 12 months of receipt.
Page 16
3D Touch
6. Pre-print checks
It is essential that all pre-print checks are carried out before starting a print on the 3D touch. This section of the manual guides the user through these checks: a. Clearing the print bed b. Check the print bed is fitted correctly c. Power up d. Test all axes e. Check the hot-end nozzles are clean from plastic debris f. Check the print bed is level g. Check the bed is referenced to the extruder nozzles h. Load the extruders i. Extruder control j. Purge the extruder k. How to start a print l. Print a successful raft
Page 17
3D Touch
Page 18
3D Touch
For transit, a white stopper is fitted to the front bed keyhole. This prevents the bed from coming off the bed arms during transport. Remove this stopper and retain for future transport. Do not print attempt to print with the white stopper in place. Remove the white bed stopper before printing.
If the model is difficult to remove from the bed in situ, you can take the whole bed out of the machine to make the removal process easier (refer to b. Check the print bed is fitted correctly).
Page 19
3D Touch
Ensure that all build material is completely removed from the bed. Use the model removal tool to remove any stuck-fast tracks. It is normal for prints to leave marks on the bed, and for the model removal tool to lightly scratch the surface of the bed. This will not affect the printer's operation. However, take care to avoid gouging the surface with the material removal tool the bed must be flat.
Page 20
3D Touch
Page 21
3D Touch
Check all bolt heads are fitted correctly (see "Check the bed is fitted correctly").
Page 22
3D Touch
c. Power up
Ensure the power cable is attached, and that power is being supplied to the printer. To start the printer, press and hold the function button for 2 seconds. This will boot the printer, activating the boot screen (the BFB logo). Touch the screen to show the home menu.
Page 23
3D Touch
Use X, Y and Z buttons to move each axis respectively. Caution: Always move the Z axis first to ensure that bed is away from the extruder nozzles, and does not collide during an X/Y move. Collisions between the extruder nozzles and the bed may damage both.
Caution: Observe each X/Y axis movement. In these axes, it is possible to drive the extruders too far away from the "Home" position (shown in the picture below) into the printer frame. Avoid this. Excessive collisions will damage the printer.
Caution: Observe each Z axis movement. In this axis, it is possible to drive the bed too high (into the extruder nozzles) or too low (into the motor coupling). Avoid this. Excessive collisions will damage the printer.
After confirming free movement for all axes, press the function button to return to the main menu.
Page 24
3D Touch
If not: Lower the bed to make access to the nozzles easy. Position the extruders in approximately the middle of the machine (see d. Test all axes), to make access to the nozzles easy. Pull away any light plastic debris away from the nozzle tip using the pliers. If plastic debris is stubborn, you may need to heat the extruder to make the plastic soft enough to remove. To heat the extruder up, please refer to i. Extruder control. Caution: When heating up nozzles to remove plastic debris, do not touch the nozzle tips with your fingers. Extruders will burn if touched when hot.
Page 25
3D Touch
The 'Level Bed' function moves the extruder carriage around the corners of the bed so the operator can adjust the bed bolts to achieve a level bed. Check the bed is fitted correctly. On the touch screen select Level Bed function:
Use the Up and Down arrows to raise and lower the bed to adjust the gap between the hot end and bed. Start with approximately 10 mm distance between the nozzle and the bed. This will enable rough levelling.
Touch the Clockwise and Anti-clockwise buttons to automatically move the carriage around the corners of the print bed (view on-screen instructions for more movement options):
Page 26
3D Touch
During each movement along the side of the bed, observe from the side of the machine any change in distance between the bed and extruder's hot-end as it moves along.
Adjust the height of the bed bolts to make each side level using the 3mm hex driver from the toolkit. Caution: Ensure that the three bolts are not tightened so much that the spring starts to become spring bound. If the springs are tightened too much, the bed will be too low for position sensing, and will hit the waste bin standoffs before registering position.
Underneath each of the 3 bed bolts is a locking nut which must be loosened with the 8mm spanner before the bolt can be adjusted.
Page 27
3D Touch
It may take several movements of the extruder, and consequent bolt adjustments to ensure that the bed is level. Ensure that axes are checked from the appropriate side of the machine (to better judge flatness):
Page 28
3D Touch
Use the Up and Down arrows to reduce the gap between the hot end and bed to approximately 2 mm. This will enable finer levelling. Repeat the levelling process. Press the Function button to leave the Level Bed menu, and return to the main menu. Caution: Observe each extruder movement. The nozzle should not touch the bed. Moving the extruder with the nozzle touching the bed will damage the nozzle and the bed. If the nozzle touches the bed, immediately lower the bed using down arrow icon.
Finally, check the centre location of the bed by pressing Y+. This can be used to identify an excessively worn or warped print bed as the height in the middle will differ from the perimeter of the bed. Press the function button to return to the main menu. Remember to lock the 3 bed bolts in position by tightening the lock nut under each, using the 8mm spanner. Whilst tightening the nut, make sure that the bolt does not spin by holding it in position with the 3mm hex driver, from the top side of the bed.
Page 29
3D Touch
Observe the gap between the nozzle and bed from the front of the machine. Press and hold the Z+/- buttons to move the bed. Start with a gap between the bed and the nozzle. Move the bed towards the nozzle. Observe the bed as it approaches the nozzle. Stop raising the bed as soon as the nozzle touches the surface of the bed. If the bed goes too far, simply move the bed back and repeat the approach. The bed should just touch the nozzle, without any compression in the bed springs:
Caution: If the nozzle is pushed too hard against the bed, the nozzle will be forced into the bed for the whole first layer of printing. This will damage the nozzle and the bed. Ensure that setting the nozzle against the bed does not compress the bed springs.
Pressing the Function button gives the option to save the setting to the printers memory, which is retained when the power is turned off. The Z offset value will be applied for each subsequent print.
Page 30
3D Touch
Page 31
3D Touch
Reel positions for each extruder are indicated below. Note: delivery tubes for each extruder run from right to left as indicated below:
Page 32
3D Touch
Load the type of materials into their reel positions according to the number of extruders in the 3D-Touch: Number of extruders in the printer 1 2 3 Material for Extruder 1 ABS or PLA ABS ABS PLA PLA Not needed in first print Material for Extruder 2 Material for Extruder 3
Page 33
3D Touch
Page 34
3D Touch
Page 35
3D Touch
See c. Setting the extruder pressure bearings to refine the spring compression on the pressure bearing (nominally 12mm).
Page 36
3D Touch
i. Extruder control
Make sure all extruders are loaded. Use 'Manual move' (see d. Test all axes) to move the extruders to the centre of the machine, and lower the bed. This makes it easy to clean any purged material. On the control panel select the Extruder control function
'Extruder control' manages one extruder at a time (E1, E2 or E3) using the buttons on the control panel.
Extrusion temperature (C) 260 195 Note: Extruders share power, therefore an extruder will heat up quicker if it is the only extruder with a high target temperature.
Page 37
3D Touch
Before purging the extruders, position the axes using the move command: position the head in the middle of the machine, and move the bed half way down the machine, away from the nozzles. This prevents damage to the bed, and allows purging to be inspected easily.
Ensure filaments are loaded into the extruders, as defined in the h. Load the extruders. Make sure the springs on the extruder pressure bearings are compressed (as detailed in c. Setting the extruder pressure bearings) enough to push the filament into the teeth of the drive shaft. Proceed by purging one extruder at a time. Heat the extruder (as shown in i. Extruder control) to the maximum temperature defined below, depending on the material in the extruder: Material ABS PLA Extrusion temperature (C) 260 195 Once the target temperature has been achieved, turn the RPM up to 30. Examine the movement of the filament at the pressure bearing. It should slowly be driven towards the nozzle. If not, ensure that the spring pressure bearing is compressed sufficiently (c. Setting the extruder pressure bearings).
Observe the end of the nozzle. A thin bead of molten plastic should come out of the nozzle. Depending on how far the filament was loaded into the extruder, this could take several minutes.
Allow material to purge for a few seconds before reducing the RPM to 0. Repeat the purge process for each extruder. Turn the machine off to allow the nozzles to cool. As the extruders cool, clean the nozzles (see "Check the hot-end nozzles are clean"). Dispose of all waste filament from the nozzle.
Page 38
3D Touch
Before starting any print, make sure that the all pre-print checks have been completed. The following sections will ask you to run two test files: a raft check file, and a duck. When asked to print a file you will need to follow the procedure below: Insert the memory stick into the 3D Touch USB slot. Select the Print icon:
Select the correct print file using the left and right arrow keys. Touch the name of the print file to start the print.
Page 39
3D Touch
It is essential that a good raft is printed to guarantee a good build. Therefore the height of the hot-end nozzle over the bed for the first layer is critical: If the nozzle is too far away from the bed, the filament will not stick to the bed If the nozzle is too low it will not be able to extruder the filament, and there is a risk of damage to the bed and the nozzle.
Page 40
3D Touch
Make sure materials are loaded as per "Load the filament". Follow the section k. How to start a print to print the appropriate raft check file for the material loaded in Extruder 1 (see table below). Material type in Extruder 1 ABS PLA File to print RaftABS_CheckFile RaftPLA_CheckFile
Examine each raft pad in the check file, as detailed in the following section. Remove the raft print when complete.
Page 41
3D Touch
Potential problems
If the raft pad appears damaged, match the imperfection to the two scenarios below, and follow the corrective action suggested. Note that there may be some imperfections in the raft, but that the process is very forgiving and even the images shown below will generally not spoil a full print.
Track ripping
Page 42
3D Touch
Purge deposit
Page 43
3D Touch
Make sure all pre-print checks are complete. Make sure materials are loaded in the order defined in the Load the extruders (this is important as the print files assume this setup). Follow the How to start a print directions to print the Duck file from the memory stick. The Duck file you must choose is determined by the number of extruders on your 3D Touch (see table below). Remember, only the first 6 characters of the filename will be displayed on the control box if the filename is longer than 8 characters. Number of extruders 1 (ABS) 1 (PLA) 2 3 File name Duck1A_E1_ABS.bfb Duck1P_E1_PLA.bfb Duck2_E1_ABSraft_E2_PLAbuild.bfb Duck2_E1_ABSraft_E2_PLAbuild.bfb (same as above)
After printing, follow the procedure detailed in Clearing the bed to remove the model from the printer. Carry out essential post-print operations (detailed in the next section). Remove the raft from the model with sandpaper. For tips on post-processing your model, check out out on-line FAQ.
Page 44
3D Touch
Page 45
3D Touch
If the bed is bowed downwards (even slightly) turn the bed over to point the bow of the bed upwards for the next print, as shown below. The next print will restore the bed's flatness, maintaining a flat bed.
If the bed is turned over: Check the print bed is fitted correctly Check the bed is level Check the bed is referenced to the extruder nozzles
Page 46
3D Touch
Lower the bed (Manual move) to access the nozzle wipe box. Remove the waste box from the machine and dispose of the plastic deposits. Re-install the waste box back into the machine, ready for your next print.
Page 47
3D Touch
If a part is very difficult to remove, persist with the scraper. Tough removal is because the nozzle was referenced at an incorrect height to the nozzle - i.e. it was too low when it started printing the first layer. Refer to the manual to ensure that the nozzle is correctly referenced before the next print.
Page 48
3D Touch
The part has left marks on the bed, what can I do about it?
Leaving marks on the print bed is normal, and will not affect the quality of your next print.
Break-away
If the support material is the same as the build material, support material will need to be scraped away using a knife. If using a knife, always wear leather gloves to prevent injury to hands.
Page 49
3D Touch
9. Further printing
Now your printer is set up, you will need to visit our Technical Resources website (visit www.bitsfrombytes.com -> Support -> Technical Resources) to: Learn how to use our STL processing software, Axon 2: The Axon 2 manual is located (here). Download Axon 2 (here). Check for free updates - we issue updates regularly to continually improve printing performance. Pick up some printing tips from our online FAQ or design for printing page.
Page 50
3D Touch
Page 51
3D Touch
Under-tightening the pressure bearing will not engage the filament with the extruder drive shaft, therefore the filament will not be driven through the nozzle.
Prepare the extruder for a purge as detailed in Purge the extruder. Set the spring compression on the pressure bearing to 12mm, as shown below:
Purge the extruder at 60 RPM for 10 minutes. Now pull out the filament from the nozzle and examine the bite marks left on the filament from the extruder drive shaft. Compare this with the chart below.
Once the correct pressure bearing setting is established it should be used for each print (this procedure does not need to be repeated before each print).
Page 52
3D Touch
Page 53
3D Touch
Remove pressure bearing. Heat up the nozzle to extrusion temperature (see Extruder control). Pull remaining filament out of extruder using pliers. After removing the remaining filament, follow the instructions inthe "Load the extruders" section to load a new filament. Purge the extruder until the old material is completely flushed out. See caution note below about purge temperature: If a new material is being loaded in to the extruder, purge at the temperature of the material which has the highest melting point. E.g. if PLA is being loaded into an extruder which previously had ABS, purge at 260 C. This ensures that the old, higher melting point, material will melt and fully flush out. Failure to do this will result in a blocked nozzle, as the higher melting point material will remain solidified in the nozzle.
Page 54
3D Touch
Use the left and right arrow buttons to scroll through the menu. Touch an icon to enter a menu. Press the function button to return to the main menu.
Run file
See Start a print.
Extruder mapping
The extruder remapping menu allows users to reassign extruders between the .BFB file and the physical printer. This makes it possible to switch materials after compiling the .BFB file without having to physically change the materials over. For example, a part compiled in Axon could use two materials: ABS for the raft in Extruder 1 and PLA for the part in Extruder 2. However, the printer is set-up with PLA in Extruder 1 and ABS in Extruder 2. The image below shows the standard mapping for the extruders.
Here the extruders are remapped so that the .BFB file Ex1 is assigned to Printer Ex2 and .BFB file Ex2 to Printer Ex1:
Page 55
3D Touch
Use the Y buttons to change the mapping. Press X+ to save, or Escape to quit without saving. The user is notified prior to printing that extruder remapping is enabled as the remapping can result in unexpected behaviour if the user is unaware of the active remapping function. The remapping configuration settings are not stored persistently as this is deemed undesirable. When the printer power is turned on the remapping reverts to 1:1 direct mapping. (The aforementioned pre-print remapping prompt is not shown when the mapping is 1:1) Please ensure the Gcode file allows enough room between the left of the print and the printer framework. I.e. attempting to print the test raft Gcode file with a double extruder RapMan will cause the extruder carriage to hit the framework when it attempts to position physical extruder 2 into the far left corners of the print bed as the raft Gcode file instructs.
Manual move
See Manual move.
Extruder control
See Extruder control.
Extruder offsets
Extruder offsets defines the position of extruders 2 and 3 in the 3D Touch, relative to extruder 1. These values are determined in the factory, and should only be changed if: a new extruder/hot-end has been installed, or multi-material prints are noticeably out of registration.
Settings here should only be changed during the calibration procedure. Click here to go to the calibration manual.
Page 56
3D Touch
Touch the value to select the parameter. Use up and down arrows to alter the values. Press the Function button to save the setting to the printers memory, which is retained when the power is turned off:
Level bed
See Check the bed is level.
Set Z height
See Check the bed is referenced to the extruder nozzles.
General settings
General settings are designed for advanced use. Defaults are shown below: Ignore G92 Enable Hopping Yes Yes
Touch the parameter to change its value Incorrect general settings will severely affect the 3D-Touch print quality. Do not change any general settings without fully understanding each setting first.
Ignore G92
The "ignore G92" setting is required because of the previous method of managing extruder offsets which involves using the Gcode G92 command. The user was required to determine the extruder 2 offset value through printing the calibration print. The calculated offset value was then entered into Axon. During Gcode generation, Axon inserts a G92 offset command to offset the carriage by the user calculated offset amount. Therefore all Axon generated Gcode files that utilise two extruders contain G92 commands to apply the extruder 2 offsets. A drawback of this approach is that the Gcode file is printer dependent because the Gcode file contains the unique extruder offsets for the printer that was calibrated. In order to make the Gcode files portable between printers, the extruder offsets are entered directly into the printer memory with firmware V4.1.0 onwards. This achieves moving the extruder offsets from the Gcode file and into the printer. When the printer utilises extruder 2, it reads the offsets from memory. When the extruder offsets are loaded from memory, the Axon generated G92 commands in the Gcode file must be ignored by the printer. Otherwise the Axon generated G92 extruder offsets will be applied in addition to the printer memory extruder offsets, resulting in print failure. Typically the desired functionality will be to ignore the Axon generated G92 offsets so the printer memory extruder offsets are applied solely. However an advanced user may want to use G92 to produce an offset for a number of reasons, in which case the "ignore G92" option is provided.
Hopping
By default this setting is enabled on the 3D-Touch and disabled on the RapMan. The setting is accessed via Settings Menu -> General Settings. Hop causes the bed to lower 1mm during a non-extruding move, and raise 1mm when the destination position has been reached. This reduces the
Page 57
3D Touch
chance of the extruder hot end hitting part of the model and causing an XY shift. It also reduces the chance of the extruder hot end knocking over a small delicate pillar shape for example.
Page 58
3D Touch
a. Power down
To turn off, hold the function button for 2 seconds when the main menu is showing.
Page 59
3D Touch
Page 60
3D Touch
Use 'Manual move' to position the nozzle over the nozzle wipe box. To adjust the height of the nozzle wipe, remove the nozzle wipe box and loosen the M3 nuts and bolts on the back of the wipeusing the 2.5mm hex driver supplied in the toolkit. Use the reference holes togauge the adjustment, and ensure that the nozzle wipe is horizontal.
Retighten the M3 nuts, replace the nozzle wipe box and re-check nozzle wipe position.
Page 61
3D Touch
Make sure that the nozzle has plastic loaded into the tip. This reduces the burring on the inside surface of the orifice. Wind the flat bed up to the nozzles. Ensure that the bed is completely flat, otherwise the nozzles will be permanently set non-level.
Position a sheet of sandpaper in between the bed and the nozzle, with the grit pointing up at the nozzle. Move the sandpaper back and forth, flat against the bed, slowly moving the bed up to grind away the lower nozzle tip. The 0.5 mm nozzle orifice only has 1.0mm thickness. Remove as little material as possible to achieve level nozzles. Do not remove more than 1.0 mm, otherwise the orifice will begin to widen, and the nozzle will be permanently damaged.
When all nozzles are level, stop sanding. Manually turn the 0.5 mm drill bit (supplied in the toolkit) 2 revolutions to remove any burrs in the orifice from the sanding process. You will need to use "Extruder control" (page 37) to melt the plastic inside the nozzle to insert the drill bit.
Caution: When heating up nozzles to melt plastic, do not touch the nozzle tips. Extruders will burn if touched when hot.
Make sure the 0.5 mm drill bit is turned straight, otherwise this may widen the orifice and damage print quality.
Page 62
3D Touch
Purge the extruder.
Page 63
3D Touch
Examine the removed filament to confirm the possible cause. Here are some suggestions: Snagged filament reel preventing filament form entering the extruder Under tightened pressure bearing Blocked nozzle from poor filament tip preparation Nozzle too close to bed during print Reload the filament, as per "Load the extruders" taking care to prepare the tip of the filament as specified.
Page 64
3D Touch
Page 65
3D Touch
Page 66
3D Touch
Page 67
3D Touch
Page 68
3D Touch
Page 69
3D Touch
Page 70
3D Touch
11. Troubleshooting
Please make sure that all steps in this manual have been followed, and the user is aware of all content in Further operations. Click Here for troubleshooting guides - Alternatively please go to: www.bitsfrombytes.com > Support > Technical Resources > Troubleshoot a problem Click Here to raise a support ticket - Alternatively please go to: www.bitsfrombytes.com > Support > Submit a ticket
Page 71
3D Touch
12. Specifications
Please visit our website at http://www.bitsfrombytes.com to view specification sheets on the 3D-Touch.
Page 72
3D Touch
13. Appendix
Manual version
Description Original release Cover page formatted to remove hard-coded version number (3.3). This table now acts as version control. Reorder of pre-print operations Material storage temperature revision
Page 73
3D Touch
Home
Error formatting macro: redirect: java.lang.NullPointerException
Page 74
3D Touch
Page 75