You are on page 1of 1

Lattice Girders

Lattice Girders are lightweight, three-dimensional steel frames that are typically fabricated of three primary bars connected by stiffening elements. The JENNMAR Lattice Girder support system achieves an excellent level of support when used in conjunction with shotcrete. This union between the lattice girder and shotcrete acts as an armor that provides balanced support and reduced consumption of shotcrete, which in turn lowers cost. This system has been designed to meet the highest mining and tunneling support requirements and the high load capacity delivers immediate support to the stabilized area. JENNMAR employs highly skilled fabricators and welders that strive to ensure that compliancy is achieved in all aspects, i.e., gage lengths, ller metals and tolerances up to 1/8 in. In conjunction with JENNMAR Specialty Engineering, least cost analysis dependent upon design is achieved at the highest levels. Project management and coordination with your on-sight installation crew provide ergonomic and immediate protection from draw rock when utilized in conjunction with JENNMARs Wire Mesh and encapsulated with shotcrete.
4

LCA & Value engineering support to insure $/lb is consumer friendly Mitigate shadowing effect presented around rolled steel beams for tunnel supports Tolerances of 1/8 in. In-house rebar bending for all #s of rebar used in Lattice Girders Aggressive FOB charges to reduce overall project overhead. 4 3
ISOMETRIC VIEW OF ASSEMBLY

STANDARD FOOT PLATE - TYPE 70

Advantages Ergonomically designed Geometrically designed to t ID of any tunnel Immediate support for SEM tunneling Built with 100% American made steel and hardware Compliant with AWS D1.1/D1.1 for Structural Welding & Weldable Rebars A36 plate materials or higher ASTM 615, 706 Gr. 60 rebar (specied) ACI compliant
D C B

C ASTM 615 #8 REBAR

D2

1 7/16"
n7/8"

1'-

H
ASTM 615 #6 REBAR

D3

SECTION B-B SCALE 1 / 3


6" ASTM 615 #8 REBAR 6 1/2" 3 1/4" 1 5/8" 1 5/8"

D1

A
1 1/4"

Technical Data - Lattice Girders

NO 1.

2.U

Types and sizes are shown for typical Lattice Girders. Dimensions and characteristics of all JENNMAR Lattice Girders are manufactured according to customer specications. 1 1/8"

REVISION

TYPE 50 70

95

115

130

D1 REBAR 6 6 6 6 8 6 6 8 6 6 8 6 6 8

D2 REBAR 8 10 8 10 11 8 10 11 8 10 11 8 10 11

D3 REBAR 4 4 4 4 4 4 4 4 4 4 4 4 4 4

H, in. 3.70 4.00 4.50 4.80 A 5.15 5.50 5.75 6.15 6.30 6.55 6.95 6.85 7.15 7.55

B, in. A, in. W, lb/ft E, in. lx, in. Sx, in. ly, in. Sy, in. ASTM 615 DE #6 REBAR 3.95 1.67 4.84 A 2.00 3.40 1.70 2.43 1.23 VIRGINIA SPECIALTY PLANT 5/8" NOTES: FR 559 WARDELL INDUSTRIAL PARK ROAD A-A TO SCALE. 1. DRAWING IS NOT 3.95 2.15 6.47 1.86 4.81 SECTION 1.35 CEDAR BLUFF, VA AN DO NOT2.58 ATTEMPT TO MEASURE! 2.66 SCALE 1 / 3 BREAK & (276)964-7000 JM 2.UNLESS SPECIFIED, MA DEBURR SHARP CORNERS. 5.60 1.67 4.84 2.42 5.54 3. WHEN IN2.29 5.37 1.92 & JM CIVIL DOUBT, ASK! TOLERANCE UNLESS 1/29/14 DATE: LATTICE MARKETING 5.60 2.15 6.47 2.19 7.64IS OWNED 3.48 5.60 2.00 THIS MATERIAL AND PRINT BY AND IS THE SOLE AND EXCLUSIVE PROPERTY OF GIRDER JENNMAR CORPORATION AN OTHERWISE SPECIFIED DRAWN: JAH WHICH IT RELATES. FEDERAL LAW PROHIBITS THE REPRODUCTION, DISPLAY, SALE OR DISPOSITION OF PROFILE THIS DOCUMEN CROSS SECTION 5.60 3.13 8.65 2.68 12.48 4.65 8.97 3.20 R N/A 4 3 7.10 1.67 4.84 2.95 8.97 MATERIAL 3.04 9.08 2.56 1 of 2 & HEAT TREAT 7.10 2.15 6.47 2.58 11.85 AND IS SUPPLIED 4.59 9.31 2.62 THIS MATERIAL AND PRINT IS OWNED BY AND IS THE SOLE AND EXCLUSIVE PROPERTY OF JENNMAR CORPORATION TO THE VENDOR ON A CONFIDENTIAL BASIS FOR THE USE IN CONNECTION WITH THE JOB T WHICH IT RELATES. FEDERAL LAW PROHIBITS THE REPRODUCTION, DISPLAY, SALE OR DISPOSITION OF THIS DOCUMENT WITHOUT EXPRESS WRITTEN CONSENT OF JENNMAR CORPORATION SIGNED BY AN OFFICER THEREOF. 7.10 4 3.13 8.65 3.18 19.44 6.10 15.27 4.30 3 2 1 8.65 1.67 4.84 3.37 12.32 3.65 13.96 3.23 8.65 2.15 6.47 2.91 16.13 5.54 14.19 3.28 8.65 3.13 8.65 3.59 26.14 7.29 23.64 5.47 8.65 1.67 4.84 3.66 14.92 4.07 13.96 3.23 8.65 2.15 6.47 3.16 19.78 6.26 14.16 3.28 8.65 3.13 8.65 3.89 31.82 8.19 23.64 5.47
2 4 3 4 3
VA
JENNMAR CORPORATION of VIRGINIA SPECIALTY PRODUCTS

3"

3.

REVISION

DECIMALS

`.005 (.127)

FRACTIONS

`1/64" (.397)

ANGLE

`0 - 30'

APPROVED FOR MFR

DRAWING NO. SHEET

where: lx = Moment of inertia of cross-section about X-X axis, ly = Moment of inertia of cross-section about Y-Y axis, Sx = Elastic section modulus about X-X axis, Sy = Elastic section modulus about Y-Y axis.

www.jennmarspecialty.com 55

(276) 964-7000

You might also like