You are on page 1of 163

Contents

Section 1

Grooved Mechanical Couplings,


Flange Adapters & Mechanical Tees
Section 2

Cast & Wrought Grooved Fittings

Section 3

Stainless Steel Series

Section 4

Valves & Flow Control Components

Section 5

Threaded Fittings & Welding Outlets

Section 6

Ring Joint, Shouldered & Plain-end Couplings

Section 7

HDPE Series

Section 8

Copper Series

Section 9

AWWA Ductile Iron Series


Connect with the Best!
Section 10

Catalog 2011

www.shurjoint.com

Technical Information

General Information
Foreword......................................................................................................3
Ductile Iron...................................................................................................4
Bolts and Nuts..............................................................................................5
Gaskets........................................................................................................6
Pressure -Temperature Ratings, Service Temperatures and
Vacuum Service............................................................................................8
Standards and Codes.................................................................................10

General Notes
1. Always read and understand all Shurjoint installation instructions before installing any
Shurjoint product.

2. Always depressurize and drain the piping system before attempting disassembly,
adjustment or removal of any piping components.
3. Designers must know and understand all relevant building and or piping standards, codes
and specifications. It is the responsibility of the designer to select and or specify the
appropriate product for the intended use and service.
4. Always refer to the maximum pressure rating and service temperature range allowed for
Shurjoint products and ensure that they are used within these parameters.

5. Special attention is required for selection of suitable gasket grades for the intended service
application.

6. All information and data contained herein supersede all previous published data. Shurjoint
reserves the right to change product designs and or specifications without notice and or
obligation. Please refer to the Shurjoint web site for the latest information.

Connect with the Best!

Catalog 2011

Copyright 2011 Shurjoint

www.shurjoint.com

Catalog 2011

Connect with the Best!

Shurjoint
A World Leader in
Mechanical Piping Components

Mechanical couplings were first developed in the 1920's and evolved into
Grooved Mechanical Couplings during the 1950's & 60's. This revolution was
further spurred in the latter half of the 20th century by advanced engineering
and innovative materials such as Ductile Iron and EPDM elastomers.

Typical Applications

Past to Present The history of

Shurjoint dates back to 1974, when the


founders produced their first grooved
couplings. These first couplings
were produced from malleable iron,
the casting material of choice at this
time. Before long foundry production
was converted to ductile iron. Ductile
iron was the ideal material, providing
for precision castings and superior
strength, without the need for further
heat treatment. EPDM (ethylene
propylene diene monomer) provided
a great advancement in synthetic
rubber elastomer compounds. This new
compound offered a service life equal
to or in some cases longer than that
of carbon steel pipe. EPDM was an
ideal gasket material for grooved piping
systems.

A World Leader With nearly four


decades of experience, Shurjoint is
recognized as a world leader in the
design and manufacture of mechanical
piping components. Shurjoint has
developed and currently offers over
3000 individual piping components in
sizes from to 96, for use with a
variety of piping materials including
carbon steel, stainless steel, ductile
iron, PVC, HDPE, CPVC and copper
tubing.

The Shurjoint Mission Our

mission is to supply the highest quality


products to customers worldwide with
an unmatched level of customer service
at a superior value. In addition to these
hallmarks, Shurjoint continuously
invests in research, engineering and
development, resulting in innovative
products and new solutions for the
changing needs of industry.

The Shurjoint Catalog In this


2011 catalog we are incorporating the
ASME/ANSI pressure & temperature
rating method. Thus allowing you to
select, specify and procure Shurjoint
piping components in the same
manner and method that you do with
other fittings, flanges, valves, pumps
and other components. Shurjoint
encourages engineers and designers to
use this classic and practical pressure
rating system when using grooved
mechanical components in place of
or in conjunction with traditional pipe
joining methods.

Connect with the Best!

HVAC

Reverse Osmosis

Fire Protection

Desalination

Water Supply & Treatment

Mining & Tunnel Boring

Plumbing

Marine

Municipal

Gas

Food Processing

Chemical

Pulp & Paper

Oil

Agriculture

Air

Taipei 101, 509.2M, the world tallest building 2004 - 2010

www.shurjoint.com

3
Copyright 2011 Shurjoint

Catalog 2011

Ductile Iron Housing Material

ASTM A536, Grade 65-45-12 (UNS F33100)










Chemical Requirements*
Minimum
Carbon, %
3.0
Silicon, %
2.5
Manganese, %
0.1
Phosphorus, %
Sulfur, %
Magnesium, %
0.03
Chromium, %
Physical Properties

Tensile strength, psi (MPa)


65,000 (448)
Yield strength, psi (MPa)
45,000 (310)
Elongation, % 12

Maximum
3.9
3.0
0.4
0.07
0.02
0.05
0.1

Ductile iron is an ideal material for grooved mechanical


components, as it provides similar or greater strength
to that of wrought or cast steel piping materials such
as; forged steel flanges - ASTM A105, carbon steel
valves - ASTM A216 WCB, wrought carbon steel pipe
- ASTM A53 Gr. B, etc. Most Shurjoint components
are made of ductile iron conforming to ASTM A536 Gr.
65-45-12 and or ASTM A395 Gr. 65-45-15.

*Reference only as chemical requirements are not specified in ASTM A536.

Ductile iron was first invented in the U.S.A. and U.K. in the late

ASTM A395, Grade 65-45-15 (UNS F33100)

1940's. Superior strength was achieved by crystallizing graphite in

Chemical Requirements
Minimum
Carbon, %
3.0
Silicon, %
Manganese, %
Not specified
Phosphorus, %
Sulfur, %
Not specified
Magnesium, %
Not specified
Chromium, %
Not specified
Physical Properties

Tensile strength, psi (MPa)


Yield strength, psi (MPa)
Elongation, %

the shape of nodules. The result was ductile iron that had tensile
and yield strength properties that were equal to or greater than some
steel castings. This superior strength combined with ductile irons
excellent castability helped to reduce the weight and cost of many
components. Because of these advantages and benefits, many
components have been converted from gray iron, malleable iron and
steel castings to ductile iron over the past 60 years. Please visit the
Ductile Iron Society website; www.ductile.org, for further information.

Sand supply unit

-------

Maximum
2.5
0.08

65,000 (448)
45,000 (310)
15

-------

Disamatic Molding Line


Max. 360 molds per hour

Pattern plate
change unit
Ductile Iron
Superior tensile strength with
good castability

Gray Iron
Excellent castability but
brittle less strength

Malleable Iron
Stronger than gray iron but
poor castability
Precision mold
conveyor

Automatic
core Setter

Disamatic molding
operation

Microstructure check

International ductile iron specifications equivalent to

Molten metal
pour

ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15 are;
SAE J434: D4512
EN1563: EN-GJS-450-10 or EN-GJS-450-15
JIS G5502: FCD450-10
SABS 936/937: SG42
Physical strength of materials comparative


ASTM

Designation
Ductile iron castings A536: Gr. 65-45-12
Ductile iron castings A395: Gr. 65-45-15
Forged carbon steel
A105
Cast carbon steel
A216: WCB
Carbon steel pipe
A53: Gr. B
Malleable iron castings A47: Gr. 32510
Gray iron castings
A126: Gr. B

4
Copyright 2011 Shurjoint

Tensile
Strength,
min. psi (MPa)
65,000 (448)
65,000 (448)
70,000 (485)
70,000 (485)
60,000 (415)
51,000 (345)
31,000 (214)

Yield
Strength,
Elongation
min. psi (MPa)
in 2, %
45,000 (310)
12
45,000 (310)
15
40,000 (250)
20
36,000 (205)
22
35,000 (240)
(29.5)
32,000 (224)
10
Not specified Not specified

Connect with the Best!

www.shurjoint.com

Catalog 2011

Bolts & Nuts


Carbon steel bolts and nuts

Shurjoint products utilize oval neck track bolts conforming to


ASTM A449 and ASTM A183 Gr. 2 and heavy duty nuts to ASTM
A563 Gr. B, available with UNC threads or ISO metric threads.
The UNC track bolts and nuts are supplied electro zinc plated
in a silver chromate color and ISO metric bolts and nuts in a
gold chromate color. Hot-dip galvanized bolts and nuts are also
available upon request.

A stainless steel bolt


fastened with a silicon
bronze nut

ASTM A193, Grade B8M (Type 316) Stainless Steel Bolts

ASTM A449, Quenched and Tempered Steel Bolts*







Chemical Requirements
Minimum
Carbon, %
0.28
Manganese, %
0.60
Phosphorus, %
Sulfur, %
Physical Properties

Maximum
0.55
0.040
0.050

Tensile strength, psi (MPa)

120,000 (825)

Yield strength, psi (MPa)

92,000 (635)

Elongation, %

14

*Equivalent to property class 8.8 bolts per ISO 898.

ASTM A183, Grade 2 Carbon Steel Track Bolts






Chemical Requirements
Minimum
Carbon, %
0.30
Phosphorus, %
Sulfur, %
Physical Properties

Tensile strength, psi (MPa)


Yield strength, psi (MPa)
Elongation, %

110,000 (760)
80,000 (550)
12

Maximum
0.05
0.06
-------

ASTM A563, Grade B Carbon and Alloy Steel Heavy Hex Nuts




Chemical Requirements (bolts)


Minimum
Carbon, %
Phosphorus, %
Sulfur, %
Physical Properties

Hardness, Rockwell

B69

Maximum
0.55
0.12
0.15
C32

Chemical Requirements
Minimum
Carbon, %
Manganese, %
Phosphorus, %
Sulfur, %
Silicon
Chromium, %
16.00
Nickel, %
10.00
Molybdenum
2.00
Physical Properties

Tensile strength, psi (MPa)


Yield strength, psi (MPa)
Elongation, %

75,000 (515)
30,000 (205)
30

Maximum
0.08
2.00
0.045
0.030
1.00
18.00
14.00
3.00
-

Silicon Bronze Nuts


ASTM B98 Alloy B Copper-Silicon Alloy (UNS No. C65100)







Chemical Requirements
Minimum
Copper, %
96.0
Lead, %
Iron, %
Zinc, %
Magnesium, %
Silicon, %
0.8
Physical Properties

Tensile strength, psi (MPa)


Yield strength, psi (MPa)
Elongation, %

55,000 (380)
20,000 (140)
11

Maximum
0.05
0.8
1.5
0.7
2.0

12

Recommended Bolt Torque

Always use factory supplied bolts and nuts for assembly of Shurjoint

Stainless steel bolts and nuts

Stainless steel track bolts and nuts, type 304 or type 316, are
supplied with Shurjoint stainless steel couplings. Track bolts and

nuts are molybdenum disulfide (MoS2) coated to inhibit galling. As


an option, silicon bronze nuts are also available to further reduce the
chance of galling.

couplings. Shown below are the general recommended torque


ranges for common sizes of carbon steel bolts. Never exceed the
recommended torque range by more than 25% as excessive torque
can lead to joint failure, personal injury and or property damage.
Always depressurize and drain the piping system before attempting
disassembly, adjustment or removal of any piping component.
Follow installation instructions for proper assembly of all Shurjoint

ASTM A193, Grade B8 (Type 304) Stainless Steel Bolts










Chemical Requirements
Minimum
Carbon, %
Manganese, %
Phosphorus, %
Sulfur, %
Silicon
Chromium, %
18.00
Nickel, %
8.00
Physical Properties

Tensile strength, psi (MPa)


Yield strength, psi (MPa)
Elongation, %

75,000 (515)
30,000 (205)
30

Connect with the Best!

Maximum
0.08
2.00
0.045
0.030
1.00
20.00
10.50
-------

components. For questions contact Shurjoint.








mm
M8
M10
M12
M16
M20

Bolt Size

in
5/16 - 18
- 16
13
- 11
- 10

Proper Torque Range


N-m
Lbs-Ft
9 - 18
7 14
20 - 30
15 22
40 - 68
30 50
81 - 122
60 90
129 - 237
96 - 175

For stainless steel bolts, reduce by 20%

www.shurjoint.com

5
Copyright 2011 Shurjoint

Catalog 2011

Rubber Gasket Compounds


The 20th century was the era of innovation in plastic
and rubber materials. Among the new synthetic rubber
compounds that most impacted our industry were
EPDM (ethylene propylene diene monomer) and Nitrile
rubbers.

EPDM is recognized as the most water resistant

NBR, Buna-N, and Nitrile

rubber available today. Good for cold & hot water,

represent the same copolymer of butadiene and

steam up to 250F (121C), waste water, water

acrylonitrile (ACN), which is inherently resistant to

with acid, deionized water and seawater. EPDM is

hydraulic fluids, lubricating oils, transmission fluids

not recommended for use with petroleum based


oils and fuels, hydrocarbon solvents and aromatic

all

Green Stripe

hydrocarbons.

and other non-polar petroleum based products

Orange Stripe

and water less than 150 F (65 C). The higher the ACN content,

Shurjoint Grade "E" EPDM is compounded per ASTM D2000


designation 2CA615A25B24F17Z. Peroxide curing and post curing
give a higher crosslink density, which provides a higher aging

the higher the resistance to oils and heat, but the lower elastic
characteristics and compression set. NBR displays poor resistance to
hot water and steam.

resistance than required in AWWA C606.


Shurjoint grade T NBR rubber is compounded based on ASTM

AWWA C606

2CA 615A25B24F17Z
Basic Requirements
Hardness, Durometer A, point
657
Tensile strength, psi, min.
1500 psi (10.34 MPa)
Elongation, %, min.
300 %
Heat Aging Properties
After aged at 212F

(100C) for 70 hours
Change in Durometer hardness, max. +10 point
Change in tensile strength, max. -25%
Change in ultimate elongation, max.
-25%
Compression Set, Method B, max.
25%

Shurjoint
Standard
605
1500 psi (10.34 MPa)
300 %
After aged at 257F
(125C) for 70 hours
+5 points
-10%
-20%
20%

Use Shurjoint Grade "E-pw" for potable water and


food processing services. The Grade "E-pw" is UL
classified per ANSI/NSF 61 for cold +86F (30C)
and hot +180F (82C) potable water services.
EPDM seals are recommended for use in breweries
as they have the least impact on the characteristics
of beer or wort.

Double Green
Stripe

Note: EPDM materials used in domestic water applications with high levels of chlorine and
or chloramines should be subjected to resistance testing, as not all materials will be suitable.
EPDM materials with higher saturated ethylene content and lower carbon black content
are recommended for chloramine and chlorine resistance. Contact Shurjoint for further
information.

D2000 designation 5BG615A14B24Z and exceeds the requirements


of AWWA C606. Grade T is a general purpose compound with a
medium ACN level. For fuels, especially those with a low aniline
point, such as premium or unleaded gasoline, ASTM referenced fuels
B & C and naphtha, use Shurjoint grade M2 Epichloro-Hydrin or
grade O Flurocarbon.

AWWA C606
Shurjoint

5BG615A14B24Z
Standard
Basic Requirements
Hardness, Durometer A, point
607
605
Tensile strength, psi, min.
1500 psi (10.34 MPa) 1500 psi (10.34 MPa)
Elongation, %, min.
300 %
300 %
When heat aged at 212F (100C)
for 70 hours
Change in Durometer hardness, max. +10 point
10 points
Change in tensile strength, max. -25%
-20%
Change in ultimate elongation, max.
-30%
-30%
Compression Set, Method B, max.
25%
25%

Use Shurjoint Grade "A" white Nitrile gaskets for


oily and greasy food products and processing,
as well as pharmaceutical and cosmetics
manufacturing. The Grade "A" is compounded
from FDA approved ingredients (CFR Title 21 Part
177.2600).

White Gasket

Use Shurjoint Grade "S" Nitrile gaskets for joints


with AWWA ductile iron pipe. Good for mineral oils,
vegetable oils, air with oil vapors and water less
than 150F (65C).

Red Stripe

Laboratory high temperature oven testing

6
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

Silicone (VMQ)

Epichloro-Hydrin (ECO)

Shurjoint Grade "L"

Shurjoint Grade "M2" compound offers good to

Silicone compound features high temperature

excellent resistance to aliphatic hydrocarbon and

range stability and low temperature flexibility.

aromatic hydrocarbon fuels at low temperatures, LP

Recommended for dry heat and air without


hydrocarbons up to 350 F (177 C). Silicone
compounds are used in many food and medical

gases & fuels, mineral oils and many solvents. ECO


Red Gasket

offers limited resistance to many organic chemicals.

White Stripe

applications as they do not impart odor or taste. Not recommended


for hot water or steam services.

Halogenated Butyl (CIIR)


Shurjoint Grade "M" CIIR is specially compounded

Chloroprene (CR, Neoprene)

for use with AWWA ductile iron pipe for water

a general purpose elastomer that demonstrates

chemicals. The compound is UL classified for

services, mild dilute acids, oil-free air and many

Shurjoint Grade "V" chloroprene rubber is

potable water use per ANSI/NSF 61.

good resistance to lubricating oils, animal &


vegetable fats and greases. Chloroprene is not

Brown Stripe

Yellow Stripe

effective in aromatic and oxygenated solvent environments and is not


recommended for hot water and steam services.

Fluorocarbon (FKM) FKM is a highly

fluorinated carbon backboned compound, which

is also known by the commercial name of Viton.


Shurjoint Grade "O" fluorocarbon compound offers
excellent resistance to harsh chemical and ozone
attack with a thermal stability to 300F (149C).

Blue Stripe

The Grade "O" gasket is recommended for use with oils, gasoline,
hydraulic fluids, hydrocarbon solvents and extended fuels that fall
outside the service parameters of grade T / NBR compounds. Not

Laboratory hot water


& steam testing

recommended for steam services. (Viton is a registered trademark of DuPont.)

Service temperatures

The following chart can

serve as a general guide for temperature and media compatibility for

Shurjoint gaskets. The range shown below is only a guide and users
should always test the gasket materials for the specific operating and
service application, as conditions can vary.




Air



Hot Water



Steam (continuous)*


Steam (intermittent)*

EPDM
NBR
VMQ
CR
Grade E
Grade T
Grade L
Grade V
-30 to +260F
-20 to +180F
-30 to +350F
-30 to +180F
-34 to +127C
-29 to +82C
-34 to +177C
-34 to +82C
212F
150F
150F
150F
100C
65C
65C
65C
230F
110C
NR
NR
NR
250F
121C

FKM
Grade O
-20 to +300F
-29 to +149C
212F
100C

ECO
Grade M2
-20 to + 160F
-29 to + 71C
150F
65C

CIIR
Grade M
-20 to + 200F
-29 to + 93C
180F
82C

NR NR NR

*Some codes do not allow the use of EPDM for steam services.

Connect with the Best!

www.shurjoint.com

7
Copyright 2011 Shurjoint

PLAIN-END PIPING SYSTEM

Catalog 2011

Pressure-Temperature Ratings

Service temperatures

Shurjoint has incorporated the ASME/ANSI nominal


pressure-temperature rating method, to identify and
describe working pressures of grooved mechanical
components, so that engineers and designers can
select Shurjoint components in the same manner
and method that they do when selecting other fittings,
flanges, valves, pumps and other piping components.

Service temperatures are limited by the flow media and gasket grade.

Refer to the chart of Pressure-Temperature Ratings for Class 125,


150, 250, 300 and 400 shown on the next page. Maximum working
pressures shown in this catalog are rounded numbers rather than
those specified in ASME/ANSI standards. All pressure ratings shown
in this catalog are based on use of cut or roll-grooved standard
weight (STD) carbon steel pipe within a temperature range of -20F
to +100F (-29C to +38C).

For example Grade "E" EPDM and Grade "T" Nitrile gaskets can be
used in the temperature ranges listed below.
Temperature Limitations
Rubber Compound


EPDM (Grade E)



Nitrile (Grade T)

Air
-30F to +260F
(-34C to +127C)
-20F to +180F
(-29C to +82C)

Water
212F
(100C)
150F
(65C)

Steam
Continuous: 230F (110C)
Not recommended

Temperature limitations are guidelines when compounds are used as a sealing gasket of
grooved mechanical components. For high temperature services, Grooved mechanical
components should be installed at accessible locations for replacement of gaskets if
required.

Vacuum Service

Standard Shurjoint gaskets are designed to seal well under vacuum


conditions up to 10 inHg (absolute)/254 mmHg (absolute) which may
occur when a system is drained.

Maximum Working Pressure at +100F (+38C)








Nominal
Rating
Class 125
Class 150
Class 250
Class 300
Class 400

ASME/ANSI
B16.1, B16.5, B16.34
175 psi
285 psi
400 psi
740 psi
990 psi

Shurjoint
2011 Catalog
175 psi (12 Bar)
300 psi (20 Bar)
400 psi (28 Bar)
750 psi (52 Bar)
1000 psi (70 Bar)

Pressures are shown in psi (pounds per square inches) and temperatures in Fahrenheit (F)
with converted pressures in Bar (MPa x 10) and temperatures in Celsius (C).

Vacuum testing

The performance parameters of grooved mechanical components


will vary depending on the pipe wall thickness, material, diameter
and the type of grooves processed. For example the pressure
rating of a Class 150 coupling used on schedule 7 pipe would be
lower than that of the same coupling used on standard wall pipe.

Refer to the Performance Data Sheet, shown on page 39, for actual
working pressures at ambient temperatures (or CWP - cold working
pressures) for each pipe schedule or wall thickness of carbon steel
and stainless steel pipes. Proof test pressures are 1.5 times the
maximum working pressures (non-shock cold water). Burst test
pressures are minimum 3 times the maximum working pressures for
sizes up to 12 and minimum 2 times for sizes 14 and above.

CWP (Cold working pressure)


Pressure ratings of grooved components that do not conform to the
applicable ASME/ANSI pressure-temperature ratings are shown in CWP.
Grooved components used for fire protection systems shall be listed by
UL and or approved by FM and or other approval bodies such as VdS,
LPCB, etc., as may be required by local authorities and or codes. Refer
to the Approved Pressure Ratings by UL and FM which are shown at the
end of this catalog. Pressure ratings of some valves that are designed to
MSS standards are also shown in CWP.

8
Copyright 2011 Shurjoint

Connect with the Best!

Hydrostatic testing - 72" R-88 coupling

www.shurjoint.com

Catalog 2011

Pressure-Temperature Ratings
Fittings, Flanges & Valves
ANSI B16.4, B16.5, B16.34 &
BS EN 1092-1

Psig

Bar
70

60

ASTM A216 Gr. WCB


ASTM A351 Gr. CF8M
ASTM A126 Class A
ASME SA105

Class 400

1000

900

800

700

600
(PN40)

EPDM

500

Class 250

400

Line

30

eam

40

Class 300

Class 150

300

rate

20

d St

(PN25)

Satu

Pressure

50

(PN16)

200

Class 125

10
100

0
-50

EPDM
NITRILE
(NBR)

100
0

50

200

300

100

AIR
WATER

Connect with the Best!

200

500
250

600
300

700 F

650
350

Temperature

AIR
WATER

150

400

STEAM

Shurjoint Gr. E (EPDM) and Gr. T (NBR, Nitrile) gaskets are


compatible with air, water and steam within the referenced
temperature ranges. As a general rule, all rubber materials
lose elasticity as temperature increases. For elevated
temperature services, GMC should be installed at accessible
locations for replacement of gaskets if required.

www.shurjoint.com

9
Copyright 2011 Shurjoint

Catalog 2011

Standards and Codes


Shurjoint production facilities are certified to ISO 9001. Products are

various approval bodies and registration authorities. Shurjoint is also

designed to conform and meet or exceed all applicable domestic and

active in industry and environmental organizations.

international standards and are listed, approved and or certified by

American Standards
ASME/ANSI

B1.1: Unified Inch Screw Threads (UNC)


B1.20.1: Pipe Threads (NPT)
B16.3: Malleable Iron Threaded Fittings
B16.5: Steel Flanges & Flanged Fittings
B16.9: Wrought Steel Butt-Welding Fittings
B16.14: Plugs, Bushings & Locknuts
B16.34: Valves Flanged & Butt-welding Ends
B16.39: Malleable Iron Threaded Unions
B16.42: Ductile Iron Flanges & Flanged Fittings
B31.1: Power Piping
B31.3: Process Piping
B31.9: Building Services Piping
B36.10: Wrought Steel Pipe
B36.19: Stainless Steel Pipe

ASTM

A53: Steel Pipe


A106: Seamless Carbon Steel Pipe
A135: Electric-Resistance-Welded Steel Pipe
A795: Steel Pipe for Fire Protection Use
B75: Seamless Copper Tube
B88: Seamless Copper Water Tube
B306: Copper Drainage Tube (DWV)
A395: Ferritic Ductile Iron
A536: Ductile Iron Castings
A351: Austenitic Stainless Steel Castings
A743: Iron-Chromium-Nickel Castings for General
Application
A744: Iron-Chromium-Nickel Castings for Severe
Service
A890: Duplex (Austenitic / Ferritic) Stainless Steel
A985: Steel Investment Castings
B584: Copper Alloy Castings
A183: Carbon Steel Track Bolts and Nuts
A193: Alloy & Stainless Steel Bolting Materials
A194: Carbon & Alloy Steel Nuts
A307: Carbon Steel Standard Fasteners
A449: Quenched and Tempered Steel Bolts
A105: Steel Forgings for Piping Components
A234: Wrought Carbon Steel Fittings

10
Copyright 2011 Shurjoint

A153: Hot-Dip Zinc Coatings


A633: Electro-Zinc Coatings
D1784: PVC and CPVC Compounds
D1785: PVC Pipe (Sch. 40, 80 & 120)
D2000: Classification System of Rubber Products
D2513: PE Gas Pressure Pipe and Fittings
D3350: PE Plastic Pipe & Fittings Materials
F1476: Grooved Mechanical Couplings
F1548: Fittings for Grooved Couplings

API

API 5L: Line Pipe


API 594: Check Valves
API 598: Valve Inspection and Testing

ANSI/AWWA

C606: Grooved and Shouldered Joints


C151/A21.51: Ductile-Iron Pipe
C153/A21.53: Ductile-Iron Compact Fittings
C901: PE Pressure Pipe and Tubing

MSS

SP-25: Standard Marking System for Valves &


Fittings
SP-67: Butterfly Valves
SP-72 Ball Valves
SP-110: Ball Valves (Grooved)
SP-136 Ductile Iron Check Valves

NFPA

NFPA 13: Installation of Sprinkler Systems

SAE

SAE J403: Chemical Compositions of SAE Carbon


Steels
SAE J1199: Mechanical and Material Requirements
for Metric Externally Threaded Steel Fasteners

ABS

IACS UR P2.11: Type Approval of Mechanical Joint

Canadian Standards

CSA B242: Grooved & Shouldered Couplings

Japanese Standards

MP006 Housing Type Joints

Approval Bodies

UL 213: Rubber Gasketed Fittings for Fire


Protection Service

Connect with the Best!

ULC/ORD-C213: Rubber Gasketed Fittings for Fire


Protection Service
FM Class 1920: Pipe Couplings and Fittings for
Aboveground Fire Protection Systems
VdS 2100-06en: Pipe Joints, Requirements and
Test Methods
LPCB LPS-1219: Requirements for Testing Pipe
Couplings
FESC: Japan Fire Equipment Safety Center
CNBOP: Scientific and Research Centre for Fire
Protection
TSUS: Technick a Skobn stav Stavebn,
n. o.

Registrations

Lloyds: Lloyds Register Quality Assurance


NYC-MEA: New York City Department of Buildings,
Materials and Equipment Acceptance
NYPA: New York Power Authority
CRN: Canadian Boiler Branch Registration
DLEG: State of Michigan Board of Mechanical
Rules
CE PED: Pressure Equipment Directory 97/23/EC

Associations

NFPA: National Fire Protection Association


NFSA: National Fire Sprinkler Association, Inc.
CASA: Canadian Automatic Sprinkler Association
IFSA: International Fire Sprinkler Association
MCAA: Mechanical Contractors Association of
America
ASHRAE: American Society of Heating,
Refrigerating and Air Conditioning Engineering

Environment

ANSI/NSF 61: Standard 61 for potable water


service
USGBC: US Green Building Council
WEF: Water Environment Federation
AMTA: American Membrane Technology
Association
USGBC: US Green Building Council
WRAS: Water Regulatory Advisory Scheme

www.shurjoint.com

Section 1

Grooved Mechanical
Couplings, Flange Adapters
& Mechanical Tees

Grooved Mechanical Couplings................................................... 12


Rigid & Flexible Couplings. ........................................................... 13
M-7 Installation-Ready Rigid Coupling................................................ 14
Z05 Rigid Coupling.............................................................................. 15
Z07 Heavy Duty Rigid Coupling.......................................................... 16
XH-1000 Extra Heavy Rigid Coupling............................................... 17
7705 Flexible Coupling....................................................................... 18
7707 Heavy Duty Flexible Coupling.................................................... 19
7707N Flexible Coupling, 14 24.................................................... 20
7707L Large Diameter Coupling........................................................ 21
7706 Reducing Coupling.................................................................... 22
G-28 Hinged Lever Coupling.............................................................. 23
C-7 Outlet Coupling............................................................................. 24
7706-T & 7771-T Transition Couplings........................................... 25
XH-70EP Extra Heavy Rigid Coupling w/EP Gasket......................... 26
Flange Adapters. ................................................................................ 27
7041 Flange Adapter, ANSI Class 125/150........................................ 28
7041 Flange Adapters, PN10/16 & BS 10 Table E............................. 29
7043 Flange Adapter, ANSI Class 300............................................... 30
49 Sandwich Plate............................................................................... 30
7180 & 7181 Universal Flange Adapters......................................... 31
7170 Solid Flange Adapters, ANSI Class 125/150............................. 32
Mechanical Tees................................................................................. 33
M21 & 7721 Mechanical Tee, Female Threaded Outlet................... 34
M22 & 7722 Mechanical Tee, Grooved-end Outlet.......................... 36
723 Saddle-Let (Small Mechanical Tee)............................................. 38
Performance Data Sheet................................................................. 39

Connect with the Best!

Catalog 2011

www.shurjoint.com

Catalog 2011

Shurjoint Grooved Mechanical


Couplings
The Shurjoint grooved piping system is one of the
most advanced, versatile, economical and reliable
systems available today. After the pipe ends are
grooved a gasket is mounted over the pipe ends. The
coupling segments are then placed over the gasket and
the bolts and nuts are fastened resulting in a secure
and leak free joint.
A coupling can be installed 3 4 times faster than a comparable
welded or brazed joint and there is no need for a flame or welding
torch on the job site. A grooved mechanical coupling can be installed
by fastening a pair of bolts and nuts while using only a wrench or
spanner, whereas a comparable flanged joint requires the fastening
of many bolts and nuts with a pair of wrenches. The grooved system
allows for easy material take-offs and unlike a threaded system, there

Helpful Information to Ensure Proper


Assembly

Some couplings and components require the housing bolt pads


to make metal-to-metal contact for proper assembly, while others
require a specific bolt torque while maintaining equal bolt pad gaps.
The icons and information below will help to identify those items to
ensure proper assembly. Read and follow all installation instructions
for the component being installed.
Metal-to-metal contact: Tighten bolts and nuts until bolt
pads make metal-to-metal contact. After metal-to-metal
contact is achieved, tighten nuts by another one quarter or one half
turn to make sure the bolts and nuts are snug and secure. No torque
wrench is required. Excessive torque may lead to bolt or joint failure.

is no need to allow for added pipe length for thread engagement.


With removal of just a few bolts one can easily access the system for
cleaning, maintenance, changes and or system expansion.

No Gap

Metal-to-metal contact

After metal-to-metal,
further tighten one
quarter or half turn

Torque required! Bolts and nuts must always be


tightened to the required torque by using a torque
wrench. Normally there will be some gaps seen between the bolt
pads after the bolts and nuts are fully tightened. Models that
require torque tightening include 2 through 4 of model
XH-1000, all sizes of models XH-70EP, SS-7X
and 79 couplings.
Always use a
torque wrench

Installation-Ready Coupling

The development of the Shurjoint installation-ready coupling


has continued the advancement of grooved systems, making it
possible to further speed installation and performance. The factory
supplied couplings are installation ready with no loose parts and no
disassembly required.

#SS-7X 10 ~ 24

Installation-Ready Coupling

12
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

#79 2 ~ 20

Catalog 2011

Rigid & Flexible


Couplings

Definition Grooved couplings are subjected

to internal pressures and exterior bending


forces during service. ASTM F1476-07

Grooved mechanical couplings


(GMC) are available in both rigid
and flexible models. A rigid
coupling is used in applications
where a rigid joint is desired,
similar to that of a traditional
flanged, welded, and or threaded
connection. To be considered rigid,
a coupling would allow less than
one degree of deflection or angular
movement.
Flexible couplings are designed to

defines a rigid coupling as a joint where


there is essentially no available free angular

Bending Moment Test bending moments


are calculated by the equation M = F (L),

and L is hanger spacing x 1/2 (feet). The


table below shows test bending moments
calculated using sch. 40 pipe with NFPA 13
hanger spacing.

shall be calculated as follows: = 60

Hanger Spacing

Water filled pipe

(minutes) [2 (minutes) x (nominal pipe


size in inches)]. In other words, when is

less than 1 degree (60 minutes), the grooved


mechanical coupling is verified as a rigid

to outside forces beyond normal static

conditions, such as seismic events or where

Bolt / Nut

coupling and when is more than 1 degree

(60 minutes), the GMC is regarded as a

M = F(L)

flexible coupling. The maximum angles for

Test Bending Moment (ASTM F1476)















Nom. Size
(inches)
1
2
2
3
4
5
6
8
10
12
14
16

Moment
N-m
549
780
1200
1645
2471
3551
4803
7663
11379
15558
18609
24299

Moment
Lb-Ft
405
575
885
1213
1823
2619
3543
5652
8393
11475
13725
17922

Flexibility Proof Test Flexibility proof

Coupling Key

testing is conducted by applying a small

#7705 Flexible Coupling

Grooved couplings become less flexible as


the pipe size increases. For sizes in excess
of 18 (450 mm) couplings are very limited in

The rigid coupling shall pass the test when


the angle has not changed more than angle .

layouts and or when systems are exposed

Coupling
Housing
Segment

Pressurized to rated
pressure

where F is weight of water filled pipe (Lbs)

applications that call for curved or deflected

Gasket

M= 25% listed moment

limited angular and axial pipe movement.

movement. Flexible couplings are used in

Groove

internally pressurized to the rated pressure.

coupling as a joint wherein there is available

and a minimum one degree of angular

vibration and or noise attenuation are a

moment to the test assembly which is

or axial pipe movement and a flexible

accommodate axial displacement, rotation

concern.

Rigidity Proof Test Rigidity proof testing

is conducted by applying 25% of the listed

bending moment, 10% of the listed moment,


to the test assembly with no internal
pressure. A 4 model 7705 or 7707 flexible
coupling deflects 3 4 degrees depending
on the type of groove processed.

their angular movement. Please refer to the


following definition and test methods.

M = 10% listed moment

No internal
pressure

Connect with the Best!

rigid couplings are shown in the table below:

Rigid Coupling - Max. Deflection















Nom. Size
(inches)
1
2
2
3
4
5
6
8
10
12
14
16

, max
(minutes)
57
56
55
54
52
50
48
44
40
36
32
28

, max.
(degrees)
0.95
0.93
0.92
0.90
0.87
0.83
0.80
0.73
0.67
0.60
0.53
0.47

Bending Moment Proof Test The

coupling shall resist a 100% listed bending


moment while the assembly is internally
pressurized to the rated pressure.

M = 100% listed moment

Pressurized to rated
pressure

www.shurjoint.com

13
Copyright 2011 Shurjoint

Catalog 2011

MODEL

M-7 INSTALLATION READY RIGID COUPLING


Patented and Patents Pending

The Shurjoint Model M-7 is designed for

required. The advanced housing and

general service applications. The advanced

Fast-Fit gasket designs result in superior

design and features make this coupling

compression and sealing dynamics while

the right choice to speed installation and

reducing the possibility of gasket pinching.

performance. The M-7 is supplied installation

Hanging requirements correspond to NFPA

ready with no loose parts and no disassembly

13, ASME B31.1 and B31.9.

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

750 psi @100F


52 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C


Class 300

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Features
Installation ready
Enhanced joint rigidity
Reduced chance of gasket pinching
Superior compression & sealing capability

Housing
Segment

Compression
Pad

Nominal Pipe Max. Working


Size
O.D.
Pressure
mm / in mm / in
Bar / PSI

50
60.3
52

2
2.375
750

65
73.0
52

2
2.875
750

80
88.9
52

3
3.500
750
100
114.3
52

4
4.500
750
125
141.3
52

5
6.500
750
150
168.3
52

6
6.625
750

Max End
Load
kN / Lbs
14.8
3320
21.8
4870
32.3
7210
53.3
11920
81.5
18220
115.6
25840

Axial
Dimension
Displacement
A
B
C
mm / in
mm / in mm / in mm / in
0 1.6
90
126
48.5
0 0.06
3.54
4.96
1.90
0 1.6
105
140
48.5
0 0.06
4.13
5.51
1.90
0 1.6
112
158
48.5
0 0.06
4.40
6.22
1.90
0 3.2
147
219
51.0
0 0.13
5.78
7.00
2.00
0 1.6
175
228
51.0
0 0.06
6.89
8.98
2.00
0 1.6
203
255
51.0
0 0.06
8.00
10.04
2.00

Bolt
Size
mm / in
M10 x 55
x 2
M10 x 55
x 2
M10 x 70
x 2
M10 x 70
x 2
M12 x 75
x 3
M12 x 75
x 3

Weight
Kgs / Lbs
0.9
2.1
1.1
2.5
1.6
3.6
2.3
5.0
3.0
6.6
3.7
8.1

Step 1

Step 2

Step 3

Place the coupling over one


pipe end. The center gasket
leg serves as your indication to stop.

Insert the second pipe end


or component into the coupling, butting it up to the
center leg of the gasket.

Tighten bolts and nuts until


the housing segments and
compression pads make
metal-to-metal contact*.

The Model M-7 is supplied factory assembled. Do not disassemble the coupling prior to installation. Gaskets and housing parts are not
interchangeable with other style couplings.

* Read and familiarize yourself with the complete Shurjoint installation instruction prior to installing, disassembling or adjusting any component.

14
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

Z05 RIGID COUPLING


Angle-Pad Design

The Shurjoint Model Z05 is an angle-pad

With the removal of only one bolt you

design rigid coupling for moderate pressure

can make a fast and easy swing-over

piping services including fire mains, long

installation.

straight runs and valve connections. The


angle-pad design allows the coupling housings
to slide along the bolt pads when tightened.
The result is an offset clamping action which
provides a rigid joint which resists so-called
snaking of a long straight run. Support and
hanging requirements correspond to ANSI
B31.1, B31.9 and NFPA 13.

Pressure-Temperature Rating


Nom. Rating



Class 150

The angle pad design allows for fast

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

and easy swing-over installation with


the removal of a single bolt.

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

32

1

40

1

50

2

65

2


76.1 mm


80

3

100

4


108.0 mm



133.0 mm



139.7 mm


125

5


159.0 mm



165.1 mm


150

6

200

8


200 JIS

Pipe
O. D.
mm / in
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
108.0
4.250
114.3
4.500
133.0
5.250
139.7
5.500
141.3
5.563
159.0
6.250
165.1
6.500
168.3
6.625
219.1
8.625
216.3
8.516

Max. Working
Pressure
Bar/PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Max. End
Load
kN / Lbs
2.80
649
3.66
850
5.71
1330
8.37
1950
9.09
2120
12.41
2885
18.31
4250
20.51
4770
27.77
6456
30.64
7125
31.35
7290
39.69
9199
42.80
9950
44.47
10340
75.37
17525
73.45
17079

Connect with the Best!

Axial
Displacement
A
mm / in
mm / in
0 ~ 1.2
66
0 ~ 0.05
2.60
0 ~ 1.2
72
0 ~ 0.05
2.83
0 ~ 1.7
85
0 ~ 0.07
3.35
0 ~ 1.7
98
0 ~ 0.07
3.86
0 ~ 1.7
100
0 ~ 0.07
3.94
0 ~ 1.7
113
0 ~ 0.07
4.45
0 ~ 4.1
142
0 ~ 0.16
5.59
0 ~ 4.1
146
0 ~ 0.16
5.75
0 ~ 4.1
170
0 ~ 0.16
6.69
0 ~ 4.1
173
0 ~ 0.16
6.81
0 ~ 4.1
175
0 ~ 0.16
6.89
0 ~ 4.1
198
0 ~ 0.16
7.80
0 ~ 4.1
200
0 ~ 0.16
7.87
0 ~ 4.1
203
0 ~ 0.16
8.00
0 ~ 4.8
264
0 ~ 0.19
10.40
0 ~ 4.8
260
0 ~ 0.19
10.24

Dimensions
B
mm / in
102
4.00
109
4.29
117
4.61
132
5.20
136
5.35
148
5.83
176
6.93
182
7.17
224
8.82
227
8.94
229
9.02
250
9.84
246
9.69
249
9.80
330
12.99
340
13.39

Bolts Size
C
mm / in
No.
mm / in
46

M10 x 55
2
1.81
x 2
46

M10 x 55
2
1.81
x 2
47

M10 x 70
2
1.85
x 2
47

M10 x 70
2
1.85
x 2
47

M10 x 70
2
1.85
x 2
48

M10 x 70
2
1.88
x 2
54

M10 x 70
2
2.13
x 2
53

M10 x 70
2
2.09
x 2
54

M12 x 75
2
213
x 3
53

M12 x 75
2
2.09
x 3
53

M12 x 75
2
2.09
x 3
54

M12 x 75
2
2.13
x 3
54

M12 x 75
2
2.13
x 3
54

M12 x 75
2
2.13
x 3
64

M16 x 135
2
2.52
x 55/16
64

M20 x 120
2
2.50
x 4

www.shurjoint.com

Weight
Kgs / Lbs
0.64
1.41
0.66
1.46
0.79
1.74
0.93
2.05
0.98
2.16
1.20
2.60
1.64
3.62
1.87
4.12
2.33
5.14
2.57
5.67
2.58
5.69
2.75
6.06
3.05
6.72
3.07
6.77
6.07
13.38
7.00
15.43

15
Copyright 2011 Shurjoint

Catalog 2011

MODEL

Z07 HEAVY DUTY RIGID COUPLING


The Shurjoint Model Z07 is an angle-pad

action which provides a rigid joint that resists

design rigid coupling for general piping

flexural and torsional loads. Support and

applications where rigidity is required

hanging requirements correspond to ANSI

including, mechanical rooms, valve

B31.1, B31.9 and NFPA 13.

connections fire mains and long straight runs.

Note: Model Z07N two-segment couplings are now available


in sizes 14 - 24. Model Z07 multi-segment couplings in sizes
14 - 24 are also available. Contact Shurjoint for the Z07 multisegment data sheet. Please specify the model required when
ordering.

The angle-pad design allows the coupling


housings to slide along the bolt pads when
tightened. The result is an offset clamping
Pressure-Temperature Rating

Working Pressure
Size
Nom. Rating

(STD, Roll-grooved)
1 6

Class 300
32 - 150
8 12

Class 250
200 - 300
14 24

Class 150
350 - 600

750 psi @100F


52 Bar @38C
400 psi @100F
28 Bar @38C
300 psi @100F
20 Bar @38C

Max. Service
Temperature

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on roll- or cut-grooved standard wall carbon


steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size
Pipe O. D.

mm / in
mm / in

32
42.2

1
1.660

40
48.3

1
1.900

50
60.3

2
2.375

65
73.0

2
2.875


76.1
76.1 mm

3.000

80
88.9

3
3.500

100
114.3

4
4.500


139.7
139.7 mm

5.500

125
141.3

5
5.563


165.1
165.1 mm

6.500

150
168.3

6
6.625

200
219.1

8
8.625

250
273.0

10
10.750

300
323.9

12
12.750


216.3
200 JIS

8.516


267.4
250 JIS

10.528


318.5
300 JIS

12.539

350 (Z07N)
355.6

14
14.000

400 (Z07N)
406.4

16
16.000

450 (Z07N)
457.2

18
18.000

500 (Z07N)
508.0

20
20.000

600 (Z07N)
609.6

24
24.000

Max. Working
Pressure
Bar/PSI
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
28
400
28
400
28
400
28
400
28
400
28
400
20
300
20
300
20
300
20
300
20
300

Max. End
Load
kN / Lbs
7.27
1620
9.52
2130
14.84
3320
21.75
4875
23.64
5300
32.26
7210
53.33
11920
79.66
17810
81.50
18220
111.27
24870
115.62
25840
105.51
23360
163.81
36290
230.59
51040
102.83
22770
157.16
34800
222.97
49370
199.53
46160
259.30
60290
328.18
76300
405.16
94200
583.43
13650

1-1/4" ~ 24"

Axial
Displacement
A
mm / in
mm / in
0~1.2
68
0 ~ 0.05
2.68
0~1.2
74
0 ~ 0.05
2.91
0~1.7
86
0 ~ 0.07
3.39
0~1.7
100
0 ~ 0.07
3.94
0~1.7
102
0 ~ 0.07
4.00
0~1.7
115
0 ~ 0.07
4.53
0~4.1
147
0 ~ 0.16
5.78
0~4.1
175
0 ~ 0.16
6.88
0~4.1
177
0 ~ 0.16
6.97
0~4.1
200
0 ~ 0.16
7.87
0~4.1
203
0 ~ 0.16
8.00
0~4.8
268
0 ~ 0.19
10.55
0~3.2
327
0 ~ 0.13
12.86
0~3.2
377
0 ~ 0.13
14.86
0~3.2
264
0 ~ 0.13
10.39
0~3.2
321
0 ~ 0.13
12.63
0~3.2
372
0 ~ 0.13
14.65
0~3.2
408
0 ~ 0.13
16.06
0~3.2
467
0 ~ 0.13
18.39
0~3.2
525
0 ~ 0.13
20.68
0~3.2
582
0 ~ 0.13
22.93
0~3.2
687
0 ~ 0.13
27.05

Dimensions
B
mm / in
105
4.13
115
4.53
120
4.72
140
5.50
146
5.75
157
6.18
199
7.83
235
9.25
235
9.25
259
10.20
263
10.35
342
13.46
431
16.98
480
18.88
340
13.39
397
15.63
452
17.80
505
19.89
554
21.84
607
23.89
698
27.47
803
31.61

Bolts Size
C
mm / in
No.
mm / in
47

M10 x 55
2
1.85
x 2
47

M10 x 55
2
1.85
x 2
48

M10 x 70
2
1.88
x 2
48

M10 x 70
2
1.88
x 2
48

M10 x 70
2
1.88
x 2
48

M12 x 75
2
1.88
x 3
54

M12 x 75
2
2.13
x 3
54

M16 x 90
2
2.13
x 3
54

M16 x 90
2
2.13
x 3
54

M16 x 90
2
2.13
x 3
54

M16 x 90
2
2.13
x 3
64

M20 x 120
2
2.52
x 4
65

---
2
2.56
x 6
65

---
2
2.56
x 6
64

M20 x 120
2
2.50
x 4
65

---
2
2.56
x 6
65

---
2
2.56
x 6
75

---
2
2.95
x 5
75

---
2
2.95
x 5
79

---
2
3.11
x 5
76

---
2
3.00
1 x 5
78

---
2
3.06
1 x 5

Contact Shurjoint for the data sheet of multi-segment type Z07 14 through 24

16
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Weight
Kgs / Lbs
0.7
1.6
0.9
2.0
1.1
2.4
1.1
2.4
1.2
2.6
1.4
3.1
2.0
4.4
3.0
6.6
3.0
6.6
3.4
7.5
3.2
7.1
7.1
15.7
10.4
27.4
11.8
26.0
7.4
16.3
10.5
23.1
12.4
27.4
16.0
35.3
17.9
30.5
22.3
40.1
26.2
57.8
32.1
70.8

Catalog 2011

MODEL

XH-1000 EXTRA HEAVY RIGID COUPLING


The Shurjoint Model XH-1000 is an extra

cut grooved pipes or components. Sizes 2

heavy rigid coupling designed for high

through 4 require a bolt torque of 60 - 70

pressure services up to 1000 psi (70 bar).

Ft-Lbs. with some bolt gaps. For sizes 6

This coupling is painted green and is

and above, the bolt pads will make metal to

supplied with a standard C-shaped gasket

metal contact when properly installed with

and heavy duty bolts and nuts. The Model

no torque wrench required.

XH-1000 can be installed on standard roll or

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature


2" - 6"
Class 400

1000 psi @100F


70 Bar @38C

EPDM: 230F / 110C

8" - 12"
Class 300

750 psi @100F


52 Bar @38C

Nitrile: 180F / 82C

*Working pressure is based on connection with cut or roll-grooved


standard wall steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
Pipe O. D.
mm / in
mm / in
50
60.3
2
2.375
65
73.0
2
2.875
80
88.9
3
3.500
100
114.3
4
4.500
150
168.3
6
6.625
200
219.1
8
8.625
250
273.0
10
10.750
300
323.9
12
12.750

Max. Working
Pressure
Bar/PSI
70
1000
70
1000
70
1000
70
1000
70
1000
52
750
52
750
52
750

Max. End
Load
kN / Lbs
20.0
4430
29.3
6490
43.4
9620
71.8
15900
155.6
34450
196.0
43800
304.2
68040
428.2
95710

Axial
Displacement
A
mm / in
mm / in
0 ~ 3.6
90
0 ~ 0.14
3.50
0 ~ 3.6
102
0 ~ 0.14
4.02
0 ~ 3.6
123
0 ~ 0.14
4.86
0 ~ 6.4
155
0 ~ 0.25
6.09
0 ~ 6.4
218
0 ~ 0.25
8.58
0 ~ 6.4
275
0 ~ 0.25
10.83
0 ~ 6.4
334
0 ~ 0.25
13.15
0 ~ 6.4
390
0 ~ 0.25
15.35

Dimensions
B
mm / in
150
5.90
168
6.62
188
7.38
222
8.74
295
11.61
364
14.33
424
16.70
480
18.90

Bolts
C
Size
mm / in
No.
in
49


2
X 2
1.92
49


2
X 2
1.92
49


2
X 2
1.92
53


2
x 4
2.10
57


2
x 5
2.25
70


2
1 x 5
2.75
75


2
1 x 5
2.95
75


2
1 x 5
2.95

Weight
Kgs / Lbs
1.6
3.4
1.7
3.8
2.2
4.8
3.8
8.4
8.0
17.6
10.9
24.0
14.2
31.2
16.7
36.7

Sizes 2 through 4 require a bolt torque of


60 70 Ft-Lbs (80 95 N-m). Normally you
can see some gaps between the bolt pads.

Sizes 6 through 12 are designed to make


a metal-to-metal contact when properly
installed.

Connect with the Best!

www.shurjoint.com

17
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7705 FLEXIBLE COUPLING


The Shurjoint Model 7705 is a standard
flexible coupling designed for use in a
variety of moderate pressure general piping

vibration, noise and seismic tremors. The


Model 7705 can even accommodate an

arced or curved piping layout. See Typical

applications. The Model 7705 coupling

Applications - Flexible Couplings on page

features flexibility that can accommodate

142.

misalignment, distortion, thermal stress,


Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal
Actual

Size
O.D.

mm / in
mm / in

25
33.7

1
1.315

32
42.4

1
1.660

40
48.3

1
1.900

50
60.3

2
2.375

65
73.0

2
2.875


76.1
76.1mm

3.000

80
88.9

3
3.500


101.6
101.6 mm

4.000


108.0
108.0 mm

4.250

100
114.3

4
4.500


133.0
133.0 mm

5.250


139.7
139.7 mm

5.500

125
141.3

5
5.563


159.0
159.0 mm

6.250


165.1
165.1 mm

6.500

150
168.3

6
6.625

200
219.1

8
8.625
200 (7705H)
219.1

8
8.625

250
273.0

10
10.750

300
323.9

12
12.750


216.3
200 JIS

8.516


267.4
250 JIS

10.528


318.5
300 JIS

12.539

Max.
Angular Movement
Dimensions
Working
Max. End
Axial
Per Coupling
Pressure
Load
Displacement
Degree
Per Pipe
A
B
C
Bar / PSI
kN / Lbs
mm / in
()
mm / m in / ft
mm / in
mm / in
mm / in
20
1.75
1.6

96
57
100
46
5 - 30
300
410
0.0625
1.16
2.24
3.94
1.81
20
2.80
1.6

76
66
103
46
4 - 20
300
650
0.0625
0.91
2.60
4.06
1.81
20
3.66
1.6

66
72
108
46
3 - 48
300
850
0.0625
0.80
2.83
4.25
1.81
20
5.71
1.6

53
84
129
48
3 - 01
300
1330
0.0625
0.63
3.31
5.08
1.89
20
8.37
1.6

44
99
142
48
2 - 30
300
1950
0.0625
0.52
3.90
5.59
1.89
20
9.09
1.6

42
102
147
48
2 - 24
300
2120
0.0625
0.50
4.02
5.79
1.89
20
12.41
1.6

36
116
169
48
2 - 04
300
2880
0.0625
0.43
4.57
6.65
1.89
20
16.21
1.6

31
129
200
52
1 - 48
300
3770
0.0625
0.38
5.07
7.90
2.05
20
18.31
3.2

59
138
192
52
3 - 24
300
4250
0.125
0.71
5.43
7.56
2.05
20
20.51
3.2

55
145
197
52
3 - 12
300
4770
0.125
0.67
5.71
7.76
2.05
20
27.77
3.2

48
165
231
52
2 - 46
300
6460
0.125
0.58
6.50
9.09
2.05
20
30.64
3.2

46
170
233
52
2 - 37
300
7120
0.125
0.55
6.69
9.17
2.05
20
31.35
3.2

45
172
234
52
2 - 36
300
7290
0.125
0.54
6.77
9.21
2.05
20
39.69
3.2

40
190
253
54
2 - 18
300
9200
0.125
0.48
7.48
9.96
2.13
20
42.80
3.2

39
196
261
54
2 - 14
300
9950
0.125
0.47
7.72
10.28
2.13
20
44.47
3.2

38
200
268
62
2 - 10
300
10340
0.125
0.45
7.87
10.55
2.44
20
75.37
3.2

28
260
350
64
1 - 40
300
17520
0.125
0.35
10.24
13.78
2.52
20
75.37
3.2

29
266
343
63
1 - 40
300
17520
0.125
0.35
10.47
13.50
2.48
20
117.01
3.2

23
343
425
64
1 - 20
300
27210
0.125
0.28
13.50
16.73
2.52
20
164.71
3.2

20
390
467
64
1 - 08
300
38280
0.125
0.24
15.35
18.39
2.52
20
73.45
3.2

30
254
348
62
1 - 42
300
17080
0.125
0.36
10.00
13.70
2.44
20
112.26
3.2

24
337
420
64
1 - 22
300
26100
0.125
0.29
13.27
16.54
2.52
20
159.26
3.2

20
389
478
64
1 - 10
300
37030
0.125
0.25
15.31
18.81
2.52

Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.
All DIN size 7705 couplings up to DN150 size and the DN200 7705H coupling are VdS approved in addition to cULus and FM approvals.

18
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Bolt
Size
Weight
mm / in
Kgs / Lbs
M10 x 45
0.6
x 1
1.3
M10 x 55
0.7
x 2
1.5
M10 x 55
0.7
x 2
1.6
M10 x 55
0.8
x 2
1.8
M10 x 55
0.9
x 2
2.0
M10 x 55
1.0
x 2
2.1
M12 x 75
1.3
x 3
2.8
M12 x 75
1.6
x 3
3.6
M12 x 75
1.9
x 3
4.1
M12 x 75
1.9
x 3
4.1
M16 x 90
2.3
5/8 x 3
5.1
M16 x 90
2.7
x 3
5.9
M16 x 90
2.7
x 3
5.9
M16 x 90
3.0
x 3
6.6
M16 x 90
3.1
x 3
6.8
M16 x 90
3.2
x 3
7.0
M16 x 90
5.8
x 3
12.8
M20 x 120
7.1
x 4
15.7
M20 x 120
8.2
x 4
18.0
---
10.8
x 6
23.8
M20 x 120
5.8
x 4
12.8
M20 x 120
8.0
x 4
17.6
---
10.3
x 6
22.6

Catalog 2011

MODEL

7707 HEAVY DUTY FLEXIBLE COUPLING


The Shurjoint Model 7707 heavy duty

that can accommodate misalignment,

flexible coupling is designed for use in a

distortion, thermal stress, vibration, noise

variety of general piping applications of

and seismic tremors. The Model 7707 can

moderate or high pressure services. Working

even accommodate an arced or curved

pressure is usually dictated by the wall


thickness and rating of the pipe being used.

piping layout. See Typical Applications -

Flexible Couplings on page 142.

The Model 7707 couplings feature flexibility


Pressure-Temperature Rating

Working Pressure
Size
Nom. Rating

(STD, Roll-grooved)
3/4 6

Class 300
20 - 150
8 12

Class 250
200 - 300

750 psi @100F


52 Bar @38C
400 psi @100F
28 Bar @38C

Max. Service
Temperature
EPDM: 230F / 110C
Nitrile: 180F / 82C

*Working pressure is based on roll- or cut-grooved standard wall carbon


steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

3/4"~12"
Nominal

Size
mm / in

20



25

1

32

1

40

1

50

2

65

2


76.1mm


80

3

100

4


139.7mm


125

5


165.1mm


150

6

200

8

250

10

300

12


200 JIS



250 JIS



300 JIS

Actual
O.D.
mm / in
26.7
1.050
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750
216.3
8.516
267.4
10.528
318.5
12.539

Max. Working
Pressure
Bar / PSI
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
28
400
28
400
28
400
28
400
28
400
28
400

Max. End
Axial
Angular Movement
Load
Displacement Per Coupling
Per Pipe
A
kN / Lbs
mm / in
()
mm / m in / ft
mm / in
2.91
1.6

116
54
6 46
650 0.0625
1.42
2.13
4.55
1.6

96
61
5 30
1020 0.0625
1.16
2.40
7.27
1.6

76
70
4 20
1620 0.0625
0.91
2.76
9.52
1.6

66
76
3 48
2130 0.0625
0.80
3.0
14.84
1.6

53
90
3 01
3320 0.0625
0.63
3.50
21.75
1.6

44
102
2 30
4870 0.0625
0.52
4.00
23.64
1.6

42
103
2 24
5300 0.0625
0.50
4.06
32.25
1.6

36
124
2 04
7210 0.0625
0.43
4.88
53.33
3.2

55
157
3 12
11920 0.125
0.67
6.18
79.66
3.2

46
186
2 37
17810 0.125
0.55
7.32
81.50
3.2

45
186
2 36
18220
0.125
0.54
7.32
111.27
3.2

39
211
2 14
24870
0.125
0.47
8.11
115.62
3.2

38
214
2 10
25840
0.125
0.45
8.24
105.51
3.2

29
276
1 40
233.60
0.125
0.35
10.86
163.81
3.2

23
343
1 20
36290
0.125
0.28
13.50
230.59
3.2

20
390
1 08
51045
0.125
0.25
15.35
102.83
3.2

30
276
1 42
22770
0.125
0.36
10.86
157.16
3.2

24
337
1 22
34800
0.125
0.29
13.27
222.97
3.2

20
389
1 10
49370
0.125
0.25
15.31

Dimensions
Bolts
B
C
Size
Weight
mm / in
mm / in
No.
mm / in
Kgs / Lbs
95
46

M10 x 45
0.6
2
3.74
1.81
x 1 1.3
99
46

M10 x 55
0.8
2
3.90
1.81
x 2 1.7
108
46

M10 x 55
1.0
2
4.25
1.81
x 2 2.1
124
45

M12 x 60
1.0
2
4.88
1.81
x 2 2.1
133
46
M12 x 75
1.2
2
5.24
1.81
x 3 2.6
150
46

M12 x 75
1.3
2
5.90
1.81
x 3 2.9
150
46

M12 x 75
1.3
2
5.90
1.81
x 3 2.9
171
48

M12 x 75
1.5
2
6.73
1.89 x 3 3.3
213
54

M16 x 90
2.1
2
8.38
2.13
x 3 4.6
241
54

M16 x 90
3.1
2
9.50
2.13
x 3 6.8
241
54

M16 x 90
3.3
2
9.50
2.13
x 3 7.2
286
54

M20 x 120
3.6
2
11.26
2.13
x 4 7.9
289
54

M20 x 120
3.7
2
11.38
2.13
x 4 8.1
356
62

---
6.6
2
14.00
2.44
x 5
14.5
425
64

---
10.6
2
16.73
2.52
x 6
23.3
467
64

---
12.0
2
18.39
2.52
x 6
26.4
356
62

M20 x 120
6.6
2
14.00
2.44
x 4 14.5
420
64

---
10.2
2
16.54
2.52
x 6
22.4
478
64

---
11.6
2
18.81
2.52
x 6
25.5

Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.

Connect with the Best!

www.shurjoint.com

19
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7707N FLEXIBLE COUPLING


The Shurjoint Model 7707N is a twosegment, flexible coupling for use with
standard pipe, roll or cut grooved to AWWA
C606 specifications. For 26", see page 21
for groove dimensions.

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 2 times the working pressure.

Size: 26"
14" ~ 24"
B

Nominal

Size
mm / in

350

14

400

16

450

18

500

20

550

22

600

24

650

26

Actual
Max. Working Pressure
O.D.
XS (0.500)* STD (0.375)
LW (0.312)
mm / in
Bar / PSI
Bar / PSI
Bar / PSI
355.6
20
20
17
14.000
300
300
250
406.4
20
20
17
16.000
300
300
250
457.2
20
20
17
18.000
300
300
250
508.0
20
20
17
20.000
300
300
250
558.8
20
20
17
22.000
300
300
250
609.6
20
20
17
24.000
300
300
250
660.4
20
20
17
26.0
300
300
250

Axial
Angular Movement
Dimensions
Bolts
Displacement
Degree Per
Per Pipe
A
B
C
Size
Weight
mm / in
Coupling () mm / m in / ft mm / in mm / in
mm / in No.
in
Kgs / Lbs
6.4

9.0
412
479
75


15.7
1 02
2
x 6
0.250
0.11
16.23
18.85
2.95
34.5
6.4

8.0
463
547
75


18.4
0 54
2
1 x 6
0.250
0.10
18.23
21.53
2.95
40.5
6.4

7.0
520
605
79


22.3
0 48
2
1 x 6
0.250
0.08
20.45
23.81
3.11
47.1
6.4

6.0
571
656
79


24.5
0 44
2
1 x 6
0.250
0.08
22.48
25.82
3.11
54.0
6.4

6.0
621.4
724.6
79


28.6
0 39
2
x 6
0.250
0.07
24.46
28.52
3.11
63.0
6.4

5.0
674
780
79


29.5
0 36
2
x 6
0.250
0.06
26.55
30.70
3.11 65.1
6.4

5.0
754
842
125.6


68.3
0 34
4
x 9
0.250
0.06
29.68
33.15
4.94
150.5

Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.
* Pressure ratings are based on cut-grooved XS carbon steel pipe.

30" 7707L couplings on a chill water system

20
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

7707L LARGE DIAMETER

COUPLING

The Shurjoint Model 7707L large diameter


couplings in sizes 28 - 42 (700mm - 1050
mm) are designed for joining large diameter
IPS pipe that can be roll grooved. All couplings
feature a six to eight segment design,
incorporating two bolts at each segment joint
to ensure a positive connection and seal.

Pressure-Temperature Rating


Nom. Rating


Class 125

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

175 psi @100F


12 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 2 times the working pressure.

40"~ 42"

28"~ 36"














Nominal
Size
mm / in
700
28
750
30
800
32
900
36
1000
40
1050
42

Pipe Max. Working Pressure


O. D.
XS (.500)* STD (.375)
LW (.312)
mm / in
Bar / PSI
Bar / PSI
Bar / PSI
711.2
17
12
9
28.0
250
175
125
762.0
17
12
9
30.0
250
175
125
812.8
17
12
9
32.0
250
175
125
914.4
17
12
9
36.0
250
175
125
1016.0
17
12
9
40.0
250
175
125
1066.8
17
12
9
42.0
250
175
125

Axial
Displacement
A
mm / in
mm / in
6.4
813
0.250
32.0
6.4
864
0.250
34.0
6.4
914
0.250
36.0
6.4
1016
0.250
40.0
6.4
1105
0.250
43.5
6.4
1156
0.250
45.5

Dimensions
Bolts
B
C
No
Size
mm / in
mm / in
in
920
127


12
x4
36.3
5.0
972
127


12
x4
38.3
5.0
1022
127


12
x4
40.3
5.0
1124
127


12
x4
44.3
5.0
1245
146


16
1 x 3
49.0
5.8
1295
146


16
1 x 3
51.5
5.8

Weight
Kgs / Lbs
82
180
95
209
94
207
96
212
123
271
140
308

* Pressure ratings are based on cut-grooved XS carbon steel pipe.

Standard Roll Groove for Large Diameter IPS Pipe


t

O.D.

B
C

1. Square cut: Max. allowable tolerances from square cut are 1.6mm (0.060).
2. The gasket seating surface A shall be free from deep scores, marks, or ridges that would prevent a positive seal.
3. The C dimensions are average values. The groove must be of uniform depth around the entire circumference. Use a
Shurjoint groove or rule to check the groove diameter.
4. The t is the minimum allowable wall thickness that may be roll-grooved.
5. The d is for reference use only. The groove depth shall be determined by the groove diameter C.
6. Flare Diameter: The pipe end that may flare when the groove is rolled shall be within this limit when measured at the
extreme end of the pipe.

d

Pipe Outside Diameter

Nominal


Size
Basic
Tolerance

mm / in
mm / in
mm / in
mm / in

650
660.4
+2.36
-0.79

26 OD
26.0
-0.093
-0.031

700
711.2
+2.36
-0.79

28 OD
28.0
-0.093
-0.031

750
762.0
+2.36
-0.79

30 OD
30.0
-0.093
-0.031

800
812.8
+2.36
-0.79

32 OD
32.0
-0.093
-0.031

900
914.4
+2.36
-0.79

36 OD
36.0
-0.093
-0.031

1000
1016.0
+2.36
-0.79

40 OD
40.0
-0.093
-0.031

1050
1066.8
+2.36
-0.79

42 OD
42.0
-0.093
-0.031

Connect with the Best!

A
+0.8, -1.6
+0.03, -0.06
mm / in
44.5
1.75
44.5
1.75
44.5
1.75
44.5
1.75
44.5
1.75
50.8
2.00
50.8
2.00

B
0.8
0.03
mm / in
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625

C
+0, -1.6
+0, -0.063
mm / in
647.7
25.5
698.5
27.5
749.3
29.5
800.1
31.5
901.7
35.5
1003.3
39.5
1054.1
41.5

d
Groove Depth
(ref)
mm / in
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25

www.shurjoint.com

t
Min. Allow
Wall thick
mm / in
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25
6.4
0.25

Max
Allowed
Flare Dia.
mm / in
665.5
26.2
716.3
28.2
767.1
30.2
817.9
32.2
919.5
36.2
1026.2
40.4
1071.9
42.2

21
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7706 REDUCING COUPLING


The Shurjoint Model 7706 reducing
coupling allows for direct reduction on a
piping run and eliminates the need for a
concentric reducer and additional couplings.
The specially designed rubber gasket helps
prevent small pipe from telescoping into

The Model 7706 coupling


should not be used with an end
cap, as the end cap could be
sucked into the pipe by the vacuum created
when a system is being drained.

larger pipe during vertical assembly.

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

40 x 32

1 x 1

50 x 40

2 x 1

65 x 50

2 x 2


76.1mm x 50


80 x 50

3 x 2

80 x 65

3 x 2


80 x 76.1mm


100 x 50

4 x 2

100 x 65

4 x 2


100 x 76.1mm


100 x 80

4 x 3


139.7mm x 100


125 x 100

5 x 4


165.1mm x 80


150 x 80

6 x 3


165.1mm x 100


150 x 100

6 x 4

200 x 150

8 x 6


200 x 165.1mm

Pipe
O. D.
mm / in
48.3 x 42.2
1.900 x 1.660
60.3 x 48.3
2.375 x 1.900
73.0 x 60.3
2.875 x 2.375
76.1 x 60.3
3.000 x 2.375
88.9 x 60.3
3.500 x 2.375
88.9 x 73.0
3.500 x 2.875
88.9 x 76.1
3.500 x 3.000
114.3 x 60.3
4.500 x 2.375
114.3 x 73.0
4.500 x 2.875
114.3 x 76.1
4.500 x 3.000
114.3 x 88.9
4.500 x 3.500
139.7 x 114.3
5.500 x 4.500
141.3 x 114.3
5.563 x 4.500
165.1 x 88.9
6.500 x 3.500
168.3 x 88.9
6.625 x 3.500
165.1 x 114.3
6.500 x 4.500
168.3 x114.3
6.625 x 4.500
219.1 x 168.3
8.625 x 6.625
219.1 x 165.1
8.625 x 6.500

Max. Working
Pressure
Bar/PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Max. End
Load
kN / Lbs
2.89
650
3.79
850
5.90
1330
5.90
1330
5.90
1330
8.66
1950
9.41
2115
5.90
1330
8.66
1950
9.41
2115
12.84
2890
21.23
4770
21.23
4770
12.84
2890
12.84
2890
18.95
4260
18.95
4260
46.03
10350
44.29
9960

Axial
Angular Movement
Dimensions
Displacement Per Coupling
Per Pipe
A
B
C
mm / in
Degree ()
mm / m in / ft
mm / in
mm / in
mm / in
0 ~ 3.2

33.0
72
108
46
3 - 48
0 ~ 0.13
0.40
2.83
4.25
1.81
0 ~ 3.2

26.0
85
122
48
3 - 02
0 ~ 0.13
0.31
3.35
4.80
1.89
0 ~ 3.2

22.0
96
144
48
2 - 30
0 ~ 0.13
0.26
3.78
5.67
1.89
0 ~ 3.2

21.0
102
138
48
2 - 24
0~0.13
0.25
4.02
5.43
1.89
0 ~ 3.2

18.0
116
168
48
2 04
0~0.13
0.22
4.57
6.61
1.89
0 ~ 3.2

18.0
116
168
48
2 - 04
0 ~ 0.13
0.22
4.57
6.61
1.89
0 ~ 3.2

18.0
116
168
48
2 - 04
0 ~ 0.13
0.22
4.57
6.61
1.89
0 ~ 4.8

21.0
146
198
52
2 - 24
0 ~ 0.19
0.25
5.75
7.80
2.05
0 ~ 4.8

21.0
146
198
52
2 - 24
0 ~ 0.19
0.25
5.75
7.80
2.05
0 ~ 4.8

21.0
146
198
52
2 - 24
0 ~ 0.19
0.25
5.75
7.80
2.05
0 ~ 4.8

21.0
146
198
52
2 - 24
0 ~ 0.19
0.25
5.75
7.80
2.05
0 ~ 6.4

23.0
160
242
52
2 - 36
0 ~ 0.25
0.27
6.30
9.84
2.05
0 ~ 6.4

23.0
160
242
52
2 - 36
0 ~ 0.25
0.27
6.30
9.84
2.05
0 ~ 6.4

20.0
202
269
52
2 - 14
0 ~ 0.25
0.23
7.95
10.59
2.05
0 ~ 6.4

19.0
208
275
52
2 - 12
0 ~ 0.25
0.23
8.19
10.83
2.05
0 ~ 6.4

20.0
202
269
52
2 - 14
0 ~ 0.25
0.23
7.95
10.59
2.05
0 ~ 6.4

19.0
208
275
52
2 - 12
0 ~ 0.25
0.23
8.19
10.83
2.05
0 ~ 6.4

15.0
260
334
57
1 - 40
0 ~ 0.25
0.18
10.24
13.15
2.24
0 ~ 6.4

15.0
260
334
57
1 - 40
0 ~ 0.25
0.18
10.24
13.15
2.24

Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.

22
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Bolts
Size
mm / in
M10 x 55
x 2
M10 x 55
x 2
M10 x 55
x 2
M10 x 55
x 2
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M20 x 120
x 4
M20 x 120
x 4

Weight
Kgs / Lbs
0.8
1.8
0.9
2.0
1.2
2.6
1.2
2.6
1.5
3.3
1.7
3.7
1.7
3.7
2.4
5.3
2.6
5.7
2.6
5.7
2.4
5.3
3.8
8.4
3.6
7.9
4.6
10.1
4.6
10.1
4.5
9.9
4.5
9.9
6.5
14.3
6.5
14.3

Catalog 2011

MODEL

g-28 hinged lever coupling


The Model G-28 Hinged Lever Coupling is
designed for quick connect and disconnect
services. The housing segments are
hinged with a locking lever handle for easy
assembly. The use of the split pin can
secure and prevent the accidental opening
of the coupling.
Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C


Class 150

Split pin

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

40

1

50

2

65

2


76.1 mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6

200

8

250

10

Pipe
O. D.
mm / in
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625
273.0
10.750

Max. Working
Pressure
Bar / PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Axial
Displacement
A
mm / in
mm / in
0 1.6
75
0 0.06
2.95
0 1.6
86
0 0.06
3.39
0 1.6
92
0 0.06
3.62
0 1.6
92
0 0.06
3.62
0 1.6
119
0 0.06
4.69
0 3.2
165
0 0.13
6.50
0 3.2
189
0 0.13
7.44
0 3.2
189
0 0.13
7.44
0 3.2
213
0 0.13
8.39
0 3.2
216
0 0.13
8.50
0 3.2
278
0 0.13
10.95
0 3.2
343
0 0.13
13.50

Dimensions
Deflection
B
C
Degree
Weight
mm / in
mm / in
()
Kgs / Lbs
118
47

1.0
3 - 48'
4.65
1.85
2.2
121
48

1.1
3 - 01'
4.76
1.89
2.4
150
48

1.4
2 - 30'
5.91
1.89
3.1
150
48

1.4
2 - 24'
5.91
1.89
3.1
163
48

1.8
2 - 14'
6.42
1.89
4.0
205
52

2.7
3 - 12'
8.07
2.05
5.9
253
52

4.9
2 - 37'
9.96
2.05
10.8
253
52

4.9
2 - 36'
9.96
2.05
10.8
278
52

6.0
2 - 14'
10.94
2.05
13.2
281
52

6.0
2 - 10'
11.06
2.05
13.2
356
62

9.7
1 - 40'
14.02
2.44
21.4
452
64

16.4
1 - 20'
17.80
2.52
36.1

Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.

Expansion Pipe

Lever handles are factory assembled tight


for safety. The use of an expansion pipe
will aid the easy opening and closing.
Expansion pipes are available upon
request.

Connect with the Best!

www.shurjoint.com

23
Copyright 2011 Shurjoint

Catalog 2011

MODEL

C-7 OUTLET COUPLING


The Model C-7 Outlet Coupling combines the

recommended for fire sprinkler and other

features of a coupling and a reducing outlet.

pipelines of moderate pressure. The C-7

The C-7 facilitates an easy reducing branch

Outlet Coupling can be used for dry pipe

outlet without the need of a mechanical

systems or vacuum services up to 10 inHg

tee or reducing tee and couplings. The C-7

or 254 mmHg, which may occur when the

is available with grooved, male threaded

system is drained.

or female threaded outlets. This fitting is

B
Grooved Outlet

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.



Run

pipe

mm / in



40

1





50

2







65

2








80

3






100

4








150

6


Nominal Size
Outlet
FPT
Gr / MPT
mm / in
mm / in
15
---

---

20
---

---
25
---
1
---
15
---

---
20
---

---
25
33.4
1
1
15
---

---
20
---

---
25
---
1
---
32
42.2
1
1
40
48.3
1
1
20
---

---
25
33.4
1
1
32
----
1
---
48.3
48.3
1
1
20
---

---
25
33.4
1
1
40
48.3
1
1
50
60.3
2
2
20
---

---
25
---
1
---
40
48.3
1
1
50
60.3
2
2

Threaded Outlet

Max.
Max.
Dimensions
Working
Axial
End
Bolt
Pressure Displacement
Load
T*
A
B
C
Size
Weight
Bar / PSI
mm / in
kN / Lbs
mm / in
mm / in
mm / in
mm / in
mm / in
Kgs / Lbs
20
20~22
52
---
114
70
1.2
300
0.81~0.88
2.06
---
4.50
2.75
2.6


20
20~22
3.7
52
---
114
70
M10 x 55
1.2
300
0.81~0.88
850
2.06
---
4.50
2.75
x 2
2.6
20
20~22
49
---
114
70
1.3
300
0.81~0.88
1.94
---
4.50
2.75
2.9


20
20~22
59
---
127
70
1.4


300
0.81~0.88
2.32
---
5.00
2.75
3.1
20
20~22
5.7
59
---
127
70
M10 X 55
1.4
300
0.81~0.88
1330
2.32
---
5.00
2.75
x 2
3.1
20
20~22
56
89
127
70
1.5
300
0.81~0.88
2.20
3.50
5.00
2.75
3.3
20
32~38
56
---
161
83
2.2


300
1.25~1.50
2.20
---
6.33
3.25
4.8
20
32~38
65
---
161
83
2.1
300
1.25~1.50
2.56
---
6.33
3.25
4.6
20
32~38
8.4
62
---
161
83
M12 X 60
2.0
300
1.25~1.50
2120
2.44
---
6.33
3.25
x 2
4.4
20
32~38
64
94
161
83
2.3
300
1.25~1.50
2.52
3.70
6.33
3.25
5.1
20
32~38
---
94
161
83
2.4


300
1.25~1.50
---
3.70
6.33
3.25
5.9
20
32~38
72
---
175
83
2.7
300
1.25~1.50
2.83
---
6.87
3.25
5.9
20
32~38
70
102
175
83
2.8
300
1.25~1.50
12.4
2.75
4.00
6.87
3.25
M12 X 75
6.2
20
32~38
2890
70.0
102.0
175.0
83.0
x 3
2.8
300
1.25~1.50
2.75
4.00
6.87
3.25
6.2
20
32~38
70.0
102
175
83
2.9
300
1.25~1.50
2.75
4.00
6.87
3.25
6.4
20
41~46
94
---
211
93
4.2
300
1.63~1.81
3.70
---
8.31
3.66
9.2
20
41~46
20.5
91
---
211
93
4.3
300
1.63~1.81
4770
3.58
---
8.31
3.66
M16 X 90
9.5
20
41~46
84
124
211
93
x 3
4.3


300
1.63~1.81
3.31
4.88
8.31
3.66
9.5

20
41~46
89.0
124
211
93
4.5
300
1.63~1.81
3.50
4.88
8.31
3.66
9.9

20
41~46
121
---
276
94
6.0
300
1.63~1.81
4.76
---
10.86
3.70
13.2
20
41~46
121
---
276
94
6.0
300
1.63~1.81
44.5
4.76
---
10.86
3.70
M16 X 90
13.2
20
41~46
9950
121
154
276
94
x 3
6.2
300
1.63~1.81
4.76
6.06
10.86
3.70
13.6
20
41~46
111.0
154
276
94
6.5
300
1.63~1.81
4.4
6.06
10.86
3.70
14.3

FPT : Female threaded outlet Gr: Grooved outlet MPT: Male threaded outlet
*T : Center of run pipe to end of outlet pipe (dimensions approximate). Female threaded outlet only.

24
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

7706-T TRANSITION COUPLING


Model 7706-T Transition Couplings allows
for a direct transition from IPS pipe sizes to
ISO pipe sizes.
Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in


2 x 76.1mm



6 x 165.1mm

Pipe
O. D.
mm / in
73.0 x 76.1
2.875 x 3.000
168.3 x 165.1
6.625 x 6.500

Max. Working
Pressure
Bar/PSI
20
300
20
300

ISO
PIPE

Max. End
Load
kN / Lbs
5.90
1330
44.29
9960

Axial
Angular Movement
Dimensions
Displacement Per Coupling
Per Pipe
A
B
C
mm / in
Degree ()
mm / m in / ft
mm / in
mm / in
mm / in
0 ~ 3.2

21.0
102
138
48
2 - 24
0 ~ 0.13
0.25
4.02
5.43
1.89
0 ~ 6.4

19.0
200
270
53
1 - 06
0 ~ 0.25
0.23
7.87
10.63
2.09

IPS
PIPE

Bolts
Size
mm / in
M10 x 55
x 2
M16 x 90
x 3

Weight
Kgs / Lbs
1.2
2.6
3.5
7.7

*Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.

MODEL

7771-T Transition coupling


The Shurjoint Model 7771-T Transition
Coupling allows for a direct transition from
IPS pipe sizes to JIS pipe sizes. Available in
nominal pipe sizes from 8 through 12 this
coupling can accommodate a combination
of pipes, valves and or fittings with a single
coupling. Bolt pads are designed to make
metal to metal contact to provide for a
secure and rigid joint.
The stepped exterior design of the housings

Stepped
Design

help to ensure the correct positioning of IPS


and JIS sides.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

IPS
PIPE

JIS
PIPE

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
200
8
250
10
300
12

Actual Pipe O.D.


IPS
JIS
mm / in
mm / in
219.1
216.3
8.625
8.515
273.0
267.4
10.750
10.528
323.9
318.5
12.750
12.539

Max. Working
Pressure
Bar / PSI
20
300
20
300
20
300

Connect with the Best!

Max.
End Load
kN / Lbs
75.37
17520
117.01
27190
164.71
38280

Total Axial
Displacement
A
mm / in
mm / in
3.2
259
0.13
10.20
3.2
316
0.13
12.46
3.2
367
0.13
14.45

Dimensions
Bolts
B
C
Size
mm / in
mm / in
mm
335
63

M16 x 135
13.19
2.50
386
63

M20 x 120
15.20
2.50
448
63

M22 x 165
17.64
2.50

www.shurjoint.com

Weight
Kgs / Lbs
7.0
15.4
9.0
19.8
11.0
24.2

25
Copyright 2011 Shurjoint

Catalog 2011

MODEL

XH-70EP EXTRA HEAVY RIGID COUPLING


With End Protection (EP) Gasket

The Model XH-70EP is designed for use

corrosion. This coupling is rated up to 2500

with plastic coated or cement lined pipe.

psi (175 bar) when used in conjunction with

The EP (end protection) gasket serves to

machined EP cut grooves and the applicable

form a continuous lined surface at the joint

pipe.

CAUTION: Always fasten the


bolts to the required torque.

and also helps protect the pipe ends from


C

A
EP Gasket

Nominal
Size
Pipe O. D.
mm / in
mm / in
50
60.3
2
2.375
65
73.0
2
2.875
80
88.9
3
3.500
100
114.3
4
4.500
150
168.3
6
6.625
200
219.1
8
8.625
250
273.0
10
10.750
300
323.9
12
12.750

Max. Working
Pressure
Bar / PSI
175
2500
175
2500
175
2500
175
2500
140
2000
140
2000
88
1250
88
1250

Max. End
Load
A
kN / Lbs
mm / in
50
90
11070
3.54
73.2
103
16220
4.06
108.6
122
24040
4.80
179.5
157
39740
6.18
311.3
218
68910
8.58
527.6
275
116790
10.83
514.8
334
113400
13.15
724.7
390
159510
15.35

Dimensions
B
mm / in
150
5.90
168
6.61
188
7.40
222
8.74
295
11.61
364
14.33
424
16.70
480
18.93

Bolt / Nut
C
Size
Torque
mm / in
No.
in
N-m / Lbs - Ft
49


80 - 120
2
x 2
1.92
60 - 90
49


80 - 120
2
x 2
1.92
60 - 90
51


80 - 120
2
x 2
2.00
60 - 90
55


100 - 135
2
x 4
2.17
74 - 170
57


170 - 275
2
x 5
2.25
125 - 200
70


275 - 400
2
1 x 5
2.75
200 - 300
75


275 - 400
2
1 x 5
2.95
200 - 300
75


275 - 400
2
1 x 5
2.95
200 - 300

Bolt
Weight
Kgs / Lbs
1.6
3.4
1.7
3.8
2.2
4.8
3.8
8.4
8.0
17.6
10.9
24.0
14.2
31.2
16.7
36.7

*Pressures quoted are based on EP cut grooved XS (Sch. 80) pipe.

EP Cut-Groove specification
1. EP cut-grooves are for plastic coated or

O.D.

the coating or lining and or create flared

Nominal
Size
Basic
mm / in
mm / in
50
60.3
2
2.375
65
73.0
2
2.875
80
88.9
3
3.500
100
114.3
4
4.500
150
168.3
6
6.625
200
219.1
8
8.625
250
273.0
10
10.750
300
323.9
12
12.750

26
Copyright 2011 Shurjoint

Shurjoint XH-70EP couplings only. Do

not roll groove pipe, which can damage

pipe ends.

cement lined pipe to be connected with

2. Always use plain-end square cut pipe. Do


not use beveled end pipe.
3. Always use an EP gasket with a XH-70EP
coupling. Do not use a standard gasket.
4. The gasket seating area shall be free
from deep scores, marks, or ridges that
could prevent a positive seal.

Pipe O. D.
Tolerance
mm / in
mm / in
+0.61
-0.61
+0.024
-0.024
+0.74
-0.74
+0.029
-0.29
+0.89
-0.79
+0.035
-0.031
+1.14
-0.79
+0.045
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031

Connect with the Best!

Gasket Seat A
Basic
Tol.
mm / in

14.27
0.25
0.562
0.010
14.27
0.25
0.562
0.010
14.27
0.25
0.562
0.010
15.37
0.38
0.605
0.015
15.37
0.38
0.605
0.015
18.14
0.38
0.714
0.015
18.14
0.38
0.714
0.015
18.14
0.38
0.714
0.015

Groove Width B
Basic
Tol.
mm / in
+0.25/+0.010
6.48
-0.13
0.255
-0.005
6.48
-0.13
0.255
-0.005
6.48
-0.13
0.255
-0.005
7.75
-0.13
0.305
-0.005
7.75
-0.13
0.305
-0.005
10.16
-0.25
0.400
-0.010
10.16
-0.25
0.400
-0.010
10.16
-0.25
0.400
-0.010

Groove Dia. C
Basic
Tol.
mm / in
+0/+0
57.15
-0.38
2.250
-0.015
69.09
-0.46
27.20
-0.018
84.94
-0.46
3.344
-0.018
110.08
-0.51
4.334
-0.020
163.96
-0.56
6.455
-0.022
214.4
-0.64
8.441
-0.025
268.28
-0.69
10.562
-0.027
318.29
-0.76
12.531
-0.030

www.shurjoint.com

Grv. Depth
d
(ref.)
1.60
0.063
1.98
0.078
1.98
0.078
2.11
0.083
2.16
0.085
2.34
0.092
2.39
0.094
2.77
0.109

Min. Wall
thickness T
mm / in
3.91
0.154
4.78
0.188
4.78
0.188
5.16
0.203
5.56
0.219
6.05
0.238
6.35
0.250
7.09
0.279

Catalog 2011

Flange Adapters
Shurjoint offers a variety of flange adapters
2 through 24 (50mm 600mm) to transition

Flange
Segment

Flange Segment

from a flanged system to a grooved system.

Gasket

Flange drillings available include ANSI Class


125/150, Class 300, PN 10/16 and BS 10
Table E.

Hinged

Gasket

Factory Supplied
Bolts & Nuts

Factory Supplied
Bolt & Nut

Flange adapters 2 through 12 are supplied


hinged as a single assembly while 14
through 24 (7041N) are supplied with two
independent segments and a draw kit.
Always use factory-supplied bolts and nuts

7041N 14" ~ 24"


(With a draw kit)

7041 2" ~ 12"

to assemble flange segments. The use of


other bolts may cause joint failure.

14 24: Supplied with a draw kit

Important Notes
1. Models 7041 and 7043 flange adapters

2. The Model 7041 flange adapter has small

interfere with the valve actuator or the

require a hard flat face for effective sealing.

triangular teeth inside the key shoulder to

mounting pad of the actuator.

When the mating surface is not adequate

prevent the pipe from rotating. The teeth

as with the serrated faces of some valves or

should be ground off when mating to a

5. Bolt tightening sequence: Like a regular

rubber-faced wafer valves, a sandwich plate

rubber-lined flange, plastic pipe and or light

flange joint, it is important to make flange

(Model 49, see page 30) must be used.

wall pipe.

faces contact parallel. Tighten nuts


alternately in the sequence of diagonally

#7041 Flange

Flange to mate
(Rubber surface)

3. Models 7041 and 7043 flange adapters

opposite pairs as shown below until the

shall not be used as anchor points for tie-

flange faces meet and make a metal-to-

rods across non-restrained joints.

metal contact.
1

4. When assembling a Model 7041 or 7043


flange adapter against a butterfly valve
or ball valve, make sure that the outside
Sandwich Plate

Interfere
#7041 Flange

Regular Flange Gasket

Butterfly Valve
6
Hinged

Connect with the Best!

7
2

Hinged
5

8
3

12

4
10

Hinged

Flange to mate
(Serrated face)
8

Sandwich Plate

Rubber faced or lined

10

7
6

Hinged

www.shurjoint.com

diameter of the flange adapters do not

12

11

27
Copyright 2011 Shurjoint

11

Catalog 2011

MODEL

7041 FLANGE ADAPTER - ANSI Class 125/150


The Shurjoint Model 7041 flange adapters
2 through 12 are supplied hinged as a
single assembly, while 14 - 24 (7041N) are
and a draw kit.

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

DE

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
550
22
600
24

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
558.8
22.000
609.6
24.000

Max. Working
Pressure
Bar / PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300

The tables show standard torque

values for proper assembly of Shurjoint


flange adapters. Use a torque wrench so
that all the nuts are tightened equally with
a same torque value. Shurjoint flange

adapters are sealed with elastic (rubber)


gaskets, which require much lower torques
than those that utilize metallic gaskets.

2 - 12 (hinged)

Max. End
Load
A
kN / Lbs
mm / in
5.71
152
1330
6.00
8.37
178
1950
7.00
12.41
190
2880
7.50
20.51
229
4770
9.00
31.35
254
7290
10.00
44.47
279
10340
11.00
75.37
343
17520
13.50
117.01
406
27210
16.00
164.71
482
38280
19.00
198.53
533
46160
21.00
259.3
597
60290
23.50
328.18
635
76300
25.80
405.18
699
94200
27.50
490.24
749
113980
29.50
583.43
813
135650
32.00

Required bolt torque

Copyright 2011 Shurjoint

Dimensions
B
C
mm / in
mm / in
121
19
4.75
0.75
140
22
5.50
0.87
152
24
6.00
0.94
191
24
7.50
0.94
216
24
8.50
0.94
241
25
9.50
1.00
298
28
11.75
1.12
362
30
14.25
1.18
432
32
17.00
1.25
476
37
18.75
1.44
540
37
21.25
1.44
578
40
22.75
1.56
635
43
25.00
1.69
692
48
27.25
1.90
749
49
29.50
1.94

7041N 14 - 24
(supplied with a draw kit)

Sealing Surface
Bolts
D
E
Size
mm / in
mm / in
No.
in
60
87
4

2.36
3.42


73
102
4

2.87
4.00


89
116
4

3.50
4.56


114
141
8

4.50
5.56


141
171
8

5.56
6.73


168
198
8

6.62
7.79


219
254
8

8.62
10.00


273
308
12

10.75
12.12


324
359
12

12.75
14.13


356
416
12
1
14.0
16.40


406
467
16
1
16.0
18.40


457
508
16
1
18.0
20.00


508
572
20
1
20.0
22.50


551
588
20
1
21.70
23.15


602
635
20
1
23.70
25.0

Weight
Kgs / Lbs
1.8
4.0
2.3
5.1
2.8
6.2
3.8
8.3
4.7
10.3
5.0
11.1
7.8
17.2
11.7
25.7
17.1
37.6
28.0
61.7
35.0
77.1
39.0
86.0
49.5
109.1
60.4
133.1
71.5
157.6

Required Torque for Model 7041


Flange Adapters (ANSI Class 125/150)

Required Torque for Model 7041


Flange Adapters (PN 10/16)

Nom. Size

inch

2"

2"

3"

4"

5"

6"

8"

10"

12"

14"

16"

18"

20"

24"

Nom. Size

mm

50

65

80

100

125

150

200

250

300

350

400

450

500

600

( ): No. of bolts

28

Tooth

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Hydrostatic Shell Test: 450 psi (30 bar) per ANSI B16.5.

Pressure-Temperature Rating


Nom. Rating

supplied with two independent segments

Connect with the Best!

Bolt Size
inch
(4)
(4)
(4)
(8)
(8)
(8)
(8)
(12)
(12)
1 (12)
1 (16)
1(16)
1 (20)
1 (20)

Required Torque
N-m
Lbs-Ft
30 - 50
22 - 37
30 - 50
22 - 37
40 - 68
30 - 50
40 - 68
30 - 50
40 - 68
30 - 50
40 - 68
30 - 50
68 - 90
50 - 66
80 - 120
59 - 89
80 - 120
59 - 89
100 - 135
74 - 100
100 - 135
74 - 100
110 - 160
81 - 118
110 - 160
81 - 118
135 - 190
100 - 140

Bolt Size
mm
M16 (4)
M16 (4)
M16 (8)
M16 (8)
M20 (8 )
M20 (8)
M20 (12)
M24 ( 12)
M24 (12)
M24 (16)
M27 (16)
M27 (20)
M30 (20)
M33 (20)

( ): No. of bolts

www.shurjoint.com

Required Torque
N-m
Lbs-Ft
30 - 50
22 - 37
30 - 50
22 - 37
40 - 68
30 - 50
40 - 68
30 - 50
40 - 68
30 - 50
40 - 68
30 - 50
68 - 90
50 - 66
80 - 120
59 - 89
80 - 120
59 - 89
100 - 135
74 - 100
100 - 135
74 - 100
110 - 160
81 - 118
110 - 160
81 - 118
135 - 190
100 - 140

Catalog 2011

MODEL

7041 FLANGE ADAPTER - PN 10 / PN 16


The Shurjoint Model 7041 flange adapter

flange adapters are supplied hinged as a

allows for a direct connection with PN 10/16

single assembly, while 14 - 24 (7041N) are

flanges. The two-segment design provides

supplied with two independent segments

an easy and fast installation. 2 through 12

and a draw kit.

Pressure-Temperature Rating


Nom. Rating



PN 16

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

225 psi @100F


16 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

E
D E

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Hydrostatic Shell Test: 1.5 times the working pressure, nonshock cold water.

Nominal
Size
mm
50
65
80
100
150
150
200
250
300
350
400
450
500
600

Pipe
O. D.
mm
60.3
76.1
88.9
114.3
165.1
168.3
219.1
273.0
323.9
355.6
406.4
457.2
508.0
609.6

Max. Working
Pressure
Bar
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Tooth
2 - 12 (hinged)

Max. End
Load
A
kN
mm
4.6
165
7.3
185
9.9
200
16.4
220
34.2
285
35.6
285
60.3
340
93.6
405
131.8
460
158.8
520
207.4
580
262.5
640
324.0
715
466.7
840

7041N 14 - 24
(supplied with a draw kit)

Dimensions
B
C
mm
mm
125
22
145
22
160
24
180
24
240
24
240
24
295
24
355
26
410
28
470
30
525
32
585
36
650
36
770
40

Sealing Surface
Bolts
D
E
Size
mm
mm
mm
No.
60
87
M16
4
76
105
M16
4
89
116
M16
8
114
141
M16
8
165
195
M20
8
168
198
M20
8
219
254
M20
12
273
308
M24
12
324
359
M24
12
356
416
M24
16
406
467
M27
16
457
508
M27
20
508
572
M30
20
610
706
M33
20

Weight
Kgs
2.3
2.6
3.2
3.4
5.1
4.6
7.8
11.4
13.7
23.0
28.0
42.5
47.0
73.0

Note: 2" - 6" flange drilling to PN10 / PN16 and 8" and above to PN16. See page 28 for required bolt torque.

MODEL

7041 FLANGE ADAPTER - BS 10-E


The Shurjoint Model 7041 flange adapter

through 12 flange adapters are supplied

allows for a direct connection with BS 10

hinged as a single assembly, while 14 - 24

Table E flanges. The two-segment design

(7041N) are supplied with two independent

provides an easy and fast installation. 2

segments and a draw kit.


A

Pressure-Temperature Rating


Nom. Rating



PN 14

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

200 psi @100F


14 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Hydrostatic Shell Test: 1.5 times the working pressure, nonshock cold water.

Nominal
Size
mm
65
80
100
125
150
200
250
300
350
400
450
500
600

Pipe
O. D.
mm
76.1
88.9
114.3
139.7
165.1
219.1
273.0
323.9
355.6
406.4
457.2
508.0
609.6

Max. Working
Pressure
Bar
14
14
14
14
14
14
14
14
14
14
14
14
14

Max. End
Load
A
kN
mm
6.36
165
8.69
184
14.36
216
21.45
254
29.96
279
52.76
337
81.91
406
115.30
457
138.97
527
181.51
578
229.73
641
283.61
705
408.4
826

Connect with the Best!

Tooth

2 - 12 (hinged)

DE

Dimensions
B
C
mm
mm
127
22
146
24
178
24
210
24
235
24
292
29
356
30
406
32
470
32
521
32
584
36
641
38
756
42

7041N 14 - 24
(supplied with a draw kit)
Sealing Surface
Bolts
D
E
Size
mm
mm
No.
in
76
105
4

89
116
4

114
141
8

140
170
8

165
195
8

219
254
8

273
308
12

324
359
12

356
416
12

406
467
12

457
508
16

508
572
16

610
706
16
1

www.shurjoint.com

Weight
Kgs
2.5
3.4
4.0
4.5
5.0
8.4
10.8
12.0
20.8
21.0
28.9
38.1
54.6

29
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7043 FLANGE ADAPTER - ANSI CLASS 300


The Shurjoint Model 7043 flange adapter

flange adapters are supplied hinged as

allows for direct connection of a grooved

a single assembly, while large sizes are

system to ANSI Class 300 flanged

supplied with separate segments.

components. 2" through 8" Model 7043


X

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

750 psi @100F


52 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 300

DE

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Hydrostatic Shell Test: 1125 psi (77 bar) per ANSI B16.5.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750

Max. Working
Pressure
Bar / PSI
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750
52
750

Max. End
Load
X
kN / Lbs
mm / in
14.84
165
3320
6.50
21.75
191
4870
7.50
32.28
210
7210
8.25
53.33
254
11920
10.00
81.50
279
18220
11.00
115.62
318
25840
12.50
195.96
381
43800
15.00
304.23
445
68040
17.50
428.25
521
95710
20.50

Dimensions
Y
Z
mm / in
mm / in
127
24
5.00
0.94
149
27
5.88
1.06
168
30
6.63
1.19
202
33
7.95
1.31
235
37
9.25
1.44
270
38
10.63
1.50
330
43
13.00
1.69
387
49
15.25
1.94
451
51
17.75
2.00

Sealing Surface
Bolts
D
E
Size
mm / in
mm / in
No.
in
60
87
8

2.36
3.41


73
99
8

2.88
3.91


89
115
8

3.50
4.53


114
140
8

4.50
5.53


141
171
8

5.56
6.72


168
198
12

6.63
7.78


219
252
12

8.63
9.94


273
313
16
1
10.75
12.31


324
364
16
1
12.75
14.31

Weight
Kgs / Lbs
2.4
5.3
3.6
7.9
4.6
10.0
7.8
17.3
9.6
21.2
12.5
27.6
16.4
36.2
25.8
56.9
35.2
77.7

MODEL

49 SANDWICH PLATE
The Model 7041 and 7043 flange adapters

Material: Mild-steel, electro-zinc plated.

require a hard flat surface for effective

Stainless steel, type 304 or 316 is available

gasket sealing. A sandwich plate is required

on request.

and should always be used when the mating


surface is not adequate as with the serrated
faces of some valves or the rubber-faced
or rubber-lined flange adapters of a wafer
valve.
E D

Sandwich plate

30
Copyright 2011 Shurjoint

Connect with the Best!

Nominal Size

mm / in

50

2

65

2

80

3

100

4

125

5

150

6

200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

www.shurjoint.com

E
mm / in
95
3.74
118
4.65
130
5.12
158
6.22
188
7.40
216
8.50
271
10.67
326
12.83
381
15.00
414
16.30
470
18.50
533
21.00
584
23.00
692
27.25

D
mm / in
54
2.13
67
2.64
81
3.19
105
4.13
128
5.00
155
6.10
205
8.07
258
10.15
305
12.00
337
13.25
387
15.25
438
17.25
489
19.25
590
23.25

Catalog 2011

MODEL

7180 UNIVERSAL FLANGE ADAPTER


The Model 7180 Universal Flange Adapter

Pressure-Temperature Rating

provides a rigid transition from a flanged



Nom. Rating

component to a grooved system. The single


unit is compatible for a range of flange types
including ANSI Class 125/150, PN10, PN16,
and JIS 10K.



Class 150

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

XY

L

Nominal
Pipe
ANSI

Size
O.D.
L
X
125 / 150

mm / in
mm / in
mm / in
mm / in
mm / in

50
60.3
64
165
121

2
2.375
2.50
6.50
4.75

65
73.0
70
185
140

2
2.875
2.75
7.28
5.50


76.1
70
185
140
76.1mm

3.000
2.75
7.28
5.50

80
88.9
70
200
152

3
3.500
2.75
7.87
6.00

100
114.3
76
229
191

4
4.500
3.00
9.00
7.50


139.7
76
250
216
139.7mm

5.500
3.00
9.84
8.50

125
141.3
76
250
216

5
5.563
3.00
9.84
8.50


165.1
76
291
241
165.1mm

6.500
3.00
11.46
9.50

150
168.3
89
291
241

6
6.625
3.50
11.46
9.50

200
219.1
102
343
298

8
8.625
4.00
13.50
11.75


216.3
102
343
298
200 JIS

8.516
4.00
13.50
11.75

Y : Flange Drilling
Bolts Size
PN
JIS
BS
10,16
10K
10E
Z
Dia
No.
Weight
mm / in
mm / in
mm / in
mm / in
mm / in
Kgs / Lbs
125
120
114
16
M16
4
2.30
4.92
4.72
4.49
0.63

4
5.10
145
140
127
16
M16
4
2.96
5.70
5.50
5.00
0.63

4
6.53
145
140
127
16
M16
4
2.90
5.70
5.50
5.00
0.63

4
6.40
160
150
146
16
M16
8
3.39
6.30
5.90
5.75
0.63

4
7.47
180
175
178
16
M16
8
3.85
7.09
6.89
7.00
0.63

8
8.49
210
210
210
22
M16 / M20
8
6.50
8.27
8.27
8.27
0.87
/
8
14.33
210
210
---
22
M16 / M20
8
6.50
8.27
8.27
---
0.87
/
8
14.33
240
240
235
24
M20
8
6.30
9.45
9.45
9.30
0.94

8
13.86
240
240
---
24
M20
8
5.72
9.45
9.45
---
0.94

8
12.58
295
290
292
29
M20
8 / 12
13.65
11.61
11.42
11.50
1.14

8 / 12
30.09
295
290
---
29
M20
8 / 12
13.65
11.61
11.42
---
1.14

8 / 12
30.09

MODEL

7181 UNIVERSAL REDUCING FLANGE ADAPTER


The Model 7181 Universal Reducing Flange

Pressure-Temperature Rating

Adapter provides a rigid transition between a



Nom. Rating

flanged piping system and a one or two-size


reduced grooved system without the need
of a concentric reducer. The flange drilling
is compatible to ANSI 125/150, PN10/16,
BS-10E and JIS 10K.



Class 150

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

XY

L

Nominal
Pipe

Size
OD
L
X
Z
mm / in
mm / in
mm / in
mm / in
mm / in

80 x 50
88.9 x 60.3
75.0
208.0
16.0

3 x 2
3.500 x 2.375
2.95
8.19
0.63
100 x 65
114.3 x 73.0
76.0
225.5
16.0

4 x 2
4.500 x 2.875
3.00
8.88
6.30

114.3 x 76.1
76.0
225.5
16.0
100 x 76.1mm

4.500 x 3.000
3.00
8.88
6.30
100 x 80
114.3 x 88.9
75.0
225.5
16.0

4 x 3
4.500 x 3.500
2.95
8.88
0.63
150 x 100
168.3 x 114.3
75.0
291.0
24.0

6 x 4
6.625 x 4.500
2.95
11.46
0.95

Connect with the Best!

Y: Flange Drilling
ANSI
PN
JIS
125 / 150
10, 16
10K
D
mm / in
mm / in
mm / in
mm / in
152
160
150
60.3
8.00
6.30
5.90
2
191
180
175
73.0
7.52
7.09
6.89
2.875
191
180
175
76.1
7.52
7.09
6.89
3.000
191
180
175
88.9
7.50
7.09
6.89
3
241
240
240
114.3
9.50
9.45
9.45
4

Bolts
Dia.
No.
mm / in
M16

8

M16

8

M16

8

M16

8

M20

8

www.shurjoint.com

Weight
Kgs / Lb
2.70
5.95
4.00
8.80
4.00
8.80
3.45
7.61
7.08
15.61

31
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7170 FLANGE ADAPTeR - ANSI CLASS 125/150


The Model 7170 Flange Adaptor provides a
rigid transition between ANSI class 125/150
flanged components and a grooved system.
Z

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 150

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Bolt Hole



Nom. Rating

X
Y

Pressure-Temperature Rating

Nominal Pipe
Bolt
Bolt Hole

Size
X
Y
Z
Size
Dia.
No.

mm / in
mm / in
mm / in
mm / in
in
in

250
406.4
362.0
30.0


1
12

10
16.00
14.25
1.18

300
483.0
432.0
32.0


1
12

12
19.00
17.00
1.25

350
533.0
476.3
35.0

1
1
12

14
21.00
18.75
1.38

400
597.0
539.7
37.0

1
1
16

16
23.50
21.25
1.46

450
635.0
577.8
40.0

1
1
16

18
25.00
22.75
1.57

500
699.0
635.0
43.0

1
1
20

20
27.50
25.00
1.69

600
813.6
749.3
48.0

1
1
20

24
32.00
29.50
1.89

32
Copyright 2011 Shurjoint

Connect with the Best!

D
mm / in
273.0
10.75
323.9
12.75
355.6
14.00
406.4
16.00
457.2
18.00
508.0
20.00
609.6
24.00

www.shurjoint.com

L
mm / in
127.0
5.00
127.0
5.00
127.0
5.00
127.0
5.00
140.0
5.50
152.0
6.00
152.0
6.00

Weight
Kgs / Lbs
22.0
48.4
28.0
61.6
49.5
108.9
50.0
110
62.5
137.5
72.0
158.4
99.5
218.9

Catalog 2011

Mechanical Tees

Hole-cutting

Shurjoint mechanical tees provide a fast

The hole-cut method of pipe preparation

and easy mid-point branch outlet, eliminating

is required when using mechanical tees,

the need for welding or the use of multiple

mechanical crosses, and saddle-lets. The

fittings. The Model M21 features a female

method of pipe preparation requires the

threaded outlet and M22 features a grooved

cutting or drilling of a specified hole size on

end outlet. Model 7721 (female threaded

the centerline of the pipe. Always use the

outlet) and 7722 (grooved end outlet) are

correct hole saw size as shown in Table 1

available in 8 sizes. The Model 723 Saddlelet features a compact-design for making

direct connections to sprinkler heads, drop


nipples and or gauges.

Ridgid Model No. HC-300


Hole Cutting Tool
16mm ( " )

and Table 1-b and never use a torch for


cutting a hole. After the hole has been
cut all rough edges must be removed and
the area within 5/8 (16mm) of the hole
Upper
Housing

Gasket

Locating
Collar

Alignment
Tab

smooth surface, free of any indentations or


projections that could affect proper gasket
sealing. The area within the A dimension
should also be inspected and must be free
of dirt, scale or any imperfection that could

Nut
Bolt

Bolt Pad

should be inspected to ensure a clean

affect proper seating or assembly of the


fitting.
Hole Size: The hole sizes are dictated by
the branch size of the mechanical tee.

Lower Housing

Table 1 Hole Sizes for Mechanical Tees


When bolts are tightened with a proper
torque, the outlet housing makes metal to
metal contact with the outer surface of the
pipe.
Metal-to-metal

Gap
It is normal to see bolt pad gaps

unit: mm/in


Branch

Size


15, 20, 25

, , 1

32, 40

1, 1

50

2

65

2

80

3

100

4

Hole Dimensions
Surface
Hole Saw Max dia. Preparation
Size
Allowed
A
38
41
89
1
1
3
51*
54*
102
2
2
4
64
67
114
2
2
4
70
73
121
2
2
4
89
92
140
3
3
5
114
118
165
4
4
6

*See Table 1-b for exception.`

Table 1-b Exception


The hole must be cleanly cut
using the correct size hole-saw
and shall have a smooth edge. Never use a
torch for cutting a hole.



Hole Dimensions
Surface
Run x Branch Hole Saw Max dia. Preparation

Size
Allowed
A
50 x 32 / 50 x 40
45
47
102
2 x1 / 2 x 1
1
1
4

Connect with the Best!

www.shurjoint.com

33
Copyright 2011 Shurjoint

Catalog 2011

MODEL

M21 MECHANICAL TEE

FEMALE THREADED OUTLET


Threads are NPT per ANSI B1.20.1 or BSPT
per ISO 7. UL/FM working pressure is 20
bar (300 psi). The Model 7721 is available
in 8" sizes.
Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C


Class 150

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal Size

Run x Branch

mm / in

50 x 15

2 x

50 x 20

2 x

50 x 25

2 x 1

50 x 32

2 x 1

50 x 40

2 x 1

65 x 15

2.5 x

65 x 20

2.5 x

65 x 25

2.5 x 1

65 x 32

2.5 x 1

65 x 40

2.5 x 1


76.1 x 15



76.1 x 20



76.1 x 25



76.1 x 32



76.1 x 40


80 x 15

3 x

80 x 20

3 x

80 x 25

3 x 1

80 x 32

3 x 1

80 x 40

3 x 1

80 x 50

3 x 2

100 x 15

4 x

100 x 20

4 x

100 x 25

4 x 1

100 x 32

4 x 1

100 x 40

4 x 1

Pipe
O. D.
mm / in
60.3 x 21.3
2.375 x 0.840
60.3 x 26.7
2.375 x 1.050
60.3 x 33.4
2.375 x 1.315
60.3 x 42.2
2.375 x 1.660
60.3 x 48.3
2.375 x 1.900
73.0 x 21.3
2.875 x 0.840
73.0 x 26.7
2.875 x 1.050
73.0 x 33.4
2.875 x 1.315
73.0 x 42.2
2.875 x 1.660
73.0 x 48.3
2.875 x 1.900
76.1 x 21.3
3.000 x 0.840
76.1 x 26.7
3.000 x 1.050
76.1 x 33.4
3.000 x 1.315
76.1 x 42.2
3.000 x 1.660
76.1 x 48.3
3.000 x 1.900
88.9 x 21.3
3.500 x 0.840
88.9 x 26.7
3.500 x 1.050
88.9 x 33.4
3.500 x 1.315
88.9 x 42.2
3.500 x 1.660
88.9 x 48.3
3.500 x 1.900
88.9 x 60.3
3.500 x 2.375
114.3 x 21.3
3.500 x 0.840
114.3 x 26.7
4.500 x 1.050
114.3 x 33.4
4.500 x 1.315
114.3 x 42.2
4.500 x 1.660
114.3 x 48.3
4.500 x 1.900

Hole Dia.
+3.2, -0 / +0.13, -0
mm / in
38
1.50
38
1.50
38
1.50
[45]
[1.75]
[45]
[1.75]
38
1.50
38
1.50
38
1.50
51
2.00
51
2.00
38
1.50
38
1.50
38
1.50
51
2.00
51
2.00
38
1.50
38
1.50
38
1.50
51
2.00
51
2.00
64
2.50
38
1.50
38
1.50
38
1.50
51
2.00
51
2.00

C
A

D
T


T*
A
mm / in
mm / in
50
63.5
1.97
2.50
50
63.5
1.97
2.50
47
63.5
1.85
2.50
52
73.0
2.05
2.87
52
76.2
2.08
3.00
56
69.9
2.20
2.75
56
69.9
2.20
2.75
53
69.9
2.09
2.75
58
76.2
2.28
3.00
58
76.2
2.28
3.00
56
69.9
2.20
2.75
56
69.9
2.20
2.75
53
69.9
2.09
2.75
58
76.2
2.28
3.00
58
76.2
2.28
3.00
60
77.8
2.36
3.06
59
77.8
2.32
3.06
61
77.8
2.40
3.06
65
82.6
2.56
3.25
71
88.9
2.80
3.50
70
88.9
2.76
3.50
72
93.7
2.83
3.69
71
93.7
2.79
3.69
73
93.7
2.87
3.69
78
92.1
3.07
3.63
84
92.1
3.31
3.63

Dimensions
B
C
D
mm / in
mm / in
mm / in
38.1
115.9
81
1.50
4.56
3.19
38.1
115.9
81
1.50
4.56
3.19
38.1
115.9
81
1.50
4.56
3.19
38.1
115.9
84
1.50
4.56
3.31
38.1
115.9
84
1.50
4.56
3.31
44.5
141.3
81
1.75
5.56
3.19
44.5
141.3
81
1.75
5.56
3.19
44.5
141.3
81
1.75
5.56
3.19
44.5
141.3
94
1.75
5.56
3.70
44.5
141.3
94
1.75
5.56
3.70
46.1
144.5
81
1.81
5.69
3.19
46.1
144.5
81
1.81
5.69
3.19
46.1
144.5
81
1.81
5.69
3.19
46.1
144.5
94
1.81
5.69
3.70
46.1
144.5
94
1.81
5.69
3.70
53.2
157.2
81
2.09
6.19
3.19
53.2
157.2
81
2.09
6.19
3.19
53.2
157.2
81
2.09
6.19
3.19
53.2
157.2
94
2.09
6.19
3.70
53.2
157.2
94
2.09
6.19
3.70
53.2
157.2
108
2.09
6.19
4.25
66.7
182.6
79.4
2.63
7.19
3.13
66.7
182.6
79.4
2.63
7.19
3.13
66.7
182.6
79.4
2.63
7.19
3.13
66.7
182.6
101.6
2.63
7.19
4.00
66.7
182.6
101.6
2.63
7.19
4.00

1. Hole diameters listed are suggested hole saw diameters. 2. *T: Take-out (Center of run to end of pipe to be engaged)
3. Special caution is required to some exceptional hole sizes shown in [ ].

34
Copyright 2011 Shurjoint

Connect with the Best!

Bolt
Size
mm / in
M10 x 55
x 2
M10 x 55
x 2
M10 x 55
x 2
M10 x 55
x 2
M10 x 55
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
1/2 x 2-3/8
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3

Weight
Kgs / Lbs
0.99
2.18
1.01
2.22
1.09
2.40
1.26
2.77
1.37
3.01
1.20
2.60
1.20
2.70
1.30
2.86
1.46
3.21
1.56
3.43
1.20
2.64
1.20
2.64
1.30
2.86
1.46
3.21
1.56
3.43
1.44
3.17
1.46
3.21
1.53
3.37
1.81
3.98
1.88
4.14
2.07
4.55
1.63
3.59
1.64
3.61
1.70
3.74
1.90
4.18
2.04
4.49

Continued on next page

www.shurjoint.com

Catalog 2011

MODEL

M21 & 7721 MECHANICAL TEES


FEMALE THREADED OUTLET
The Shurjoint Model M21 & 7721 mechanical

tees provides a fast and easy mid-pipe


threaded branch outlet. Threads are NPT
per ANSI B1.20.1 or BSPT per ISO 7. UL/FM
working pressure is 20 bar (300 psi).

D
T

Continued from previous page


Nominal Size

Run x Branch

mm / in

100 x 50

4 x 2

100 x 65

4 x 2


100 x 76.1


100 x 80

4 x 3


139.7 x 50



139.7 x 76.1



139.7 x 80


125 x 50

5 x 2

125 x 65

5 x 2

125 x 80

5 x 3


165.1 x 32



165.1 x 40



165.1 x 50



165.1 x 65



165.1 x 76.1



165.1 x 80



165.1 x 100


150 x 32

6 x 1

150 x 40

6 x 1

150 x 50

6 x 2

150 x 65

6 x 2


150 x 76.1


150 x 80

6 x 3

150 x 100

6 x 4

Pipe
O. D.
mm / in
114.3 x 60.3
4.500 x 2.375
114.3 x 73.0
4.500 x 2.875
114.3 x 76.1
4.500 x 3.000
114.3 x 88.9
4.500 x 3.500
139.7 x 60.3
5.500 x 2.375
139.7 x 76.1
5.500 x 3.000
139.7 x 88.9
5.500 x 3.500
141.3 x 60.3
5.563 x 2.375
141.3 x 73.0
5.563 x 2.875
141.3 x 88.9
5.563 x 3.500
165.1 x 42.2
6.500 x 1.660
165.1 x 48.3
6.500 x 1.900
165.1 x 60.3
6.500 x 2.375
165.1 x 73.0
6.500 x 2.875
165.1 x 76.1
6.500 x 2.875
165.1 x 88.9
6.500 x 3.500
165.1 x 114.3
6.500 x 4.500
168.3 x 42.2
6.625 x 1.660
168.3 x 48.3
6.625 x 1.900
168.3 x 60.3
6.625 x 2.375
168.3 x 73.0
6.625 x 2.875
168.3 x 76.1
6.625 x 2.875
168.3 x 88.9
6.625 x 3.500
168.3 x 114.3
6.625 x 4.500

Hole Dia.
+3.2, -0 / +0.13, -0
mm / in
64
2.50
70
2.75
70
2.75
89
3.50
64
2.50
70
2.75
89
3.50
64
2.50
70
2.75
89
3.50
51
2.00
51
2.00
64
2.50
70
2.75
70
2.75
89
3.50
114
4.50
51
2.00
51
2.00
64
2.50
70
2.75
70
2.75
89
3.50
114
4.50


T*
A
mm / in
mm / in
83
101.6
3.27
4.00
73
101.6
2.87
4.00
73
101.6
2.87
4.00
84
104.8
3.31
4.13
83
120.7
3.27
4.75
93
120.7
3.67
4.75
97
127.0
3.82
4.75
83
120.7
3.27
4.75
93
120.7
3.67
4.75
97
127.0
3.82
4.75
112
130.2
4.41
5.13
112
130.2
4.41
5.13
111
130.2
4.37
5.13
101
130.2
3.98
5.13
101
130.2
3.98
5.13
110
139.7
4.33
5.50
113
146.1
4.45
5.75
112
130.2
4.41
5.13
112
130.2
4.41
5.13
111
130.2
4.37
5.13
101
130.2
3.98
5.13
101
130.2
3.98
5.13
110
139.7
4.33
5.50
113
146.1
4.45
5.75

Dimensions
B
C
D
mm / in
mm / in
mm / in
66.7
182.6
101.6
2.63
7.19
4.00
66.7
182.6
112.7
2.63
7.19
4.44
66.7
182.6
112.7
2.63
7.19
4.44
66.7
182.6
128.6
2.63
7.19
5.06
81.0
223.8
106.4
3.19
8.81
4.19
81.0
223.8
115.9
3.19
8.81
4.57
81.0
223.8
131.8
3.19
8.81
5.19
81.0
223.8
106.4
3.19
8.81
4.19
81.0
223.8
112.7
3.19
8.81
4.44
81.0
223.8
131.8
3.19
8.81
5.19
94.5
250.8
92.1
3.72
9.87
3.63
94.5
250.8
92.1
3.72
9.87
3.63
94.5
250.8
106.4
3.72
9.87
4.19
94.5
250.8
112.7
3.72
9.87
4.44
94.5
250.8
115.9
3.72
9.87
4.56
94.5
250.8
131.8
3.72
9.87
5.19
94.5
250.8
158.8
3.72
9.87
6.25
94.5
250.8
92.1
3.72
9.87
3.63
94.5
250.8
92.1
3.72
9.87
3.63
94.5
250.8
106.4
3.72
9.87
4.19
94.5
250.8
112.7
3.72
9.87
4.44
94.5
250.8
115.9
3.72
9.87
4.56
94.5
250.8
131.8
3.72
9.87
5.19
94.5
250.8
158.8
3.72
9.87
6.25

Bolt
Size
mm / in
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
5/8 x 3-1/2
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3

Weight
Kgs / Lbs
2.27
5.00
2.47
5.43
2.57
5.65
2.91
6.41
2.90
6.38
3.40
7.40
3.82
8.41
2.90
6.38
3.39
7.46
3.82
8.40
2.53
5.57
3.00
6.60
3.17
6.97
3.58
7.88
3.75
8.25
4.13
9.09
4.77
10.50
2.91
6.41
2.99
6.58
3.18
7.00
3.58
7.88
3.58
7.88
4.10
9.02
4.76
10.47

Pipe
O. D.
mm / in
219.1 x 60.3
8.625 x 2.375
219.1 x 73.0
8.625 x 2.875
219.1 x 76.1
8.625 x 3.000
219.1 x 114.3
8.625 x 4.500

Hole Dia.
+3.2, -0 / +0.13, -0
mm / in
[70]
[2.75]
70
2.75
89
3.50
114
4.50


T*
A
mm / in
mm / in
135
166
5.31
6.54
137
166
5.39
6.54
136
166
5.35
6.54
133
166
5.24
6.54

Dimensions
B
C
D
mm / in
mm / in
mm / in
120
327
101
4.72
12.87
3.98
120
327
104
4.72
12.87
4.09
120
327
128
4.72
12.87
5.04
120
327
164
4.72
12.87
6.46

Bolt
Size
mm / in
M20 x 120
x 4
M20 x 120
x 4
M20 x 120
x 4
M20 x 120
x 4

Weight
Kgs / Lbs
6.2
13.6
6.2
13.7
7.1
15.6
8.0
17.6

MODEL 7721

Nominal Size
Run x Branch
mm / in
200 x 50
8 x 2
200 x 65
8 x 2.5
200 x 80
8 x 3
200 x 100
8 x 4

1. Hole diameters listed are suggested hole saw diameters. 2. *T: Take-out (Center of run to end of pipe to be engaged)
3. Special caution is required to some exceptional hole sizes shown in [ ].

Connect with the Best!

www.shurjoint.com

35
Copyright 2011 Shurjoint

Catalog 2011

MODEL

M22 MECHANICAL TEE

GROOVED-END OUTLET

The groove dimensions conform to AWWA


C606. UL/FM working pressure is 20 bar
(300 psi). The Model 7722 is available in

8" sizes.
A

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C


Class 150

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size
Run x Branch

mm / in

50 x 25

2 x 1

50 x 32

2 x 1

50 x 40

2 x 1

65 x 25

2 x 1

65 x 32

2 x 1

65 x 40

2 x 1


76.1 x 25



76.1 x 32



76.1 x 40


80 x 25

3 x 1

80 x 32

3 x 1

80 x 40

3 x 1

80 x 50

3 x 2

100 x 25

4 x 1

100 x 32

4 x 1

100 x 40

4 x 1

100 x 50

4 x 2

100 x 65

4 x 2


100 x 76.1


100 x 80

4 x 3


139.7 x 50



139.7 x 76.1



139.7 x 80


125 x 50

5 x 2

125 x 65

5 x 2


125 x 76.1


125 x 80

5 x 3

Pipe
O. D.
mm / in
60.3 x 33.4
2.375 x 1.315
60.3 x 42.2
2.375 x 1.660
60.3 x 48.3
2.375 x 1.900
73.0 x 33.4
2.875 x 1.315
73.0 x 42.2
2.875 x 1.660
73.0 x 48.3
2.875 x 1.900
76.1 x 33.4
3.000 x 1.315
76.1 x 42.2
3.000 x 1.660
76.1 x 48.3
3.000 x 1.900
88.9 x 33.4
3.500 x 1.315
88.9 x 42.2
3.500 x 1.660
88.9 x 48.3
3.500 x 1.900
88.9 x 60.3
3.500 x 2.375
114.3 x 33.4
4.500 x 1.315
114.3 x 42.2
4.500 x 1,660
114.3 x 48.3
4.500 x 1.900
114.3 x 60.3
4.500 x 2.375
114.3 x 73.0
4.500 x 2.875
114.3 x 76.1
4.500 x 3.000
114.3 x 88.9
4.500 x 3.500
139.7 x 60.3
5.500 x 2.375
139.7 x 76.1
5.500 x 3.000
139.7 x 88.9
5.500 x 3.500
141.3 x 60.3
5.563 x2.375
141.3 x 73.0
5.563x 2.875
141.3 x 76.1
5.563x 3.000
141.3 x 88.9
5.563 x 3.500

Hole Dia.
+3.2, -0 / +0.13, -0
mm / in
38
1.50
[45]
[1.75]
[45]
[1.75]
38
1.50
51
2.00
51
2.00
38
1.50
51
2.00
51
2.00
38
1.50
51
2.00
51
2.00
64
2.50
38
1.50
51
2.00
51
2.00
64
2.50
70
2.75
70
2.75
89
3.50
64
2.50
70
2.75
70
2.75
64
2.50
70
2.75
70
2.75
70
2.75


A
mm / in
73.0
2.87
76.2
3.00
76.2
3.00
79.4
3.13
82.6
3.25
82.6
3.25
79.4
3.13
82.6
3.25
82.6
3.25
85.7
3.37
90.5
3.56
90.5
3.56
90.5
3.56
93.7
3.69
92.1
3.63
92.1
3.63
101.6
4.00
101.6
4.00
101.6
4.00
104.8
4.13
120.7
4.75
120.7
4.75
117.5
4.63
120.7
4.75
120.7
4.75
120.7
4.75
117.5
4.63

B
mm / in
38.1
1.50
38.1
1.50
38.1
1.50
44.5
1.75
44.5
1.75
44.5
1.75
46.1
1.81
46.1
1.81
46.1
1.81
53.2
2.09
53.2
2.09
53.2
2.09
53.2
2.09
66.7
2.63
66.7
2.63
66.7
2.63
66.7
2.63
66.7
2.63
66.7
2.63
66.7
2.63
81.0
3.19
81.0
3.19
81.0
3.19
81.0
3.19
81.0
3.19
81.0
3.19
81.0
3.19

Dimensions
C
D
mm / in
mm / in
115.9
81.0
4.57
3.19
115.9
84.0
4.57
3.31
115.9
84.0
4.57
3.31
141.3
81.0
5.56
3.19
141.3
94.0
5.56
3.70
141.3
94.0
5.56
3.70
144.5
81.0
5.69
3.19
144.5
94.0
5.69
3.70
144.5
94.0
5.69
3.70
157.2
81.0
6.19
3.19
157.2
94.0
6.19
3.70
157.2
94.0
6.19
3.70
157.2
108.0
6.19
4.25
182.6
79.4
7.19
3.13
182.6
101.6
7.19
4.00
182.6
101.6
7.19
4.00
182.6
101.6
7.19
4.00
182.6
112.7
7.19
4.44
182.6
112.7
7.19
4.44
182.6
128.6
7.19
5.06
223.8
106.4
8.81
4.19
223.8
112.7
8.81
4.44
223.8
131.8
8.81
5.19
223.8
106.4
8.81
4.19
223.8
112.7
8.81
4.44
223.8
112.7
8.81
4.44
223.8
131.8
8.81
5.19

Bolt
Size
mm / in
M10 x 55
x 2
M10 x 55
x 2
M10 x 55
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 60
x 2
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M12 x 75
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3

1. Hole diameters listed are suggested hole saw diameters. 2. Special caution is required to some exceptional hole sizes shown in [ ].

36
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Weight
Kgs / Lbs
1.03
2.27
1.11
2.44
1.18
2.60
1.23
2.71
1.39
3.06
1.42
3.12
1.23
2.71
1.39
3.06
1.42
3.12
1.45
3.19
1.68
3.70
1.70
3.74
1.83
4.03
1.65
3.63
1.80
3.96
1.81
3.98
1.93
4.25
2.66
5.85
2.17
4.78
2.41
5.30
2.63
5.79
2.95
6.50
3.08
6.78
2.63
5.79
2.88
6.34
2.95
6.49
3.08
6.78

Continued on next page

Catalog 2011

MODEL

M22 & 7722 MECHANICAL TEE

GROOVED-END OUTLET

The groove dimensions conform to AWWA


C606. UL/FM working pressure is 20 bar
(300 psi). The Model 7722 is available in
8" sizes.
C

A
B

Continued from previous page (Model M22)

Nominal Size
Run x Branch

mm / in


165.1 x 32



165.1 x 40



165.1 x 50



165.1 x 76.1



165.1 x 80



165.1 x 100


150 x 32

6 x 1

150 x 40

6 x 1

150 x 50

6 x 2

150 x 65

6 x 2

150 x 80

6 x 3

150 x 100

6 x 4

Pipe
O. D.
mm / in
165.1 x 42.2
6.500 x 1.660
165.1 x 48.3
6.500 x 1.900
165.1 x 60.3
6.500 x 2.375
165.1 x 76.1
6.500 x 3.000
165.1 x 88.9
6.500 x 3.500
165.1 x 114.3
6.500 x 4.500
168.3 x 42.2
6.625 x 1.660
168.3 x 48.3
6.625 x 1.900
168.3 x 60.3
6.625 x 2.375
168.3 x 73.0
6.625 x 2.875
168.3 x 88.9
6.625 x 3.500
168.3 x 114.3
6.625 x 4.500

Hole Dia.
+3.2, -0 / +0.13, -0
mm / in
51
2.00
51
2.00
64
2.50
70
2.75
89
3.50
114
4.50
51
2.00
51
2.00
64
2.50
70
2.75
89
3.50
114
4.50


A
mm / in
130.2
5.13
130.2
5.13
130.2
5.13
130.2
5.13
130.2
5.13
137.1
5.40
130.2
5.13
130.2
5.13
130.2
5.13
130.2
5.13
130.2
5.13
137.1
5.40

B
mm / in
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72
94.5
3.72

Dimensions
C
D
mm / in
mm / in
250.8
92.1
9.87
3.63
250.8
92.1
9.87
3.63
250.8
106.4
9.87
4.19
250.8
115.9
9.87
4.56
250.8
131.8
9.87
5.19
250.8
158.8
9.87
6.25
250.8
92.1
9.87
3.63
250.8
92.1
9.87
3.63
250.8
106.4
9.87
4.19
250.8
112.7
9.87
4.44
250.8
131.8
9.87
5.19
250.8
158.8
9.87
6.25

Bolt
Size
mm / in
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
5/8 x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3
M16 x 90
x 3

Weight
Kgs / Lbs
2.74
6.03
2.78
6.12
2.91
6.40
3.38
7.44
3.64
8.01
4.05
8.91
2.75
6.05
2.78
6.12
2.92
6.42
3.22
7.08
3.68
8.10
4.05
8.91

Pipe
O. D.
mm / in
219.1 x 60.3
8.625 x 2.375
219.1 x 73.0
8.625 x 2.875
219.1 x 76.1
8.625 x 3.000
219.1 x 88.9
8.625 x 3.500
219.1 x 114.3
8.625 x 4.500

Hole Dia.
+3.2, -0 / +0.13, -0
mm / in
[70]
[2.75]
70
2.75
70
2.75
89
3.50
114
4.50


A
mm / in
166
6.54
166
6.54
166
6.54
166
6.54
166
6.54

B
mm / in
120
4.72
120
4.72
120
4.72
120
4.72
120
4.72

Dimensions
C
D
mm / in
mm / in
327
104
12.87
3.89
327
104
12.87
4.09
327
104
12.87
4.09
327
128
12.87
5.04
327
164
12.87
6.46

Bolt
Size
mm / in
M20 x 120
x 4
M20 x 120
x 4
M20 x 120
x 4
M20 x 120
x 4
M20 x 120
x 4

Weight
Kgs / Lbs
5.8
12.8
6.0
13.2
6.0
13.2
7.2
15.8
7.5
16.5

MODEL 7722

Nominal Size
Run x Branch

mm / in

200 x 50

8 x 2

200 x 65

8 x 2


200 x 76.1


200 x 80

8 x 3

200 x 100

8 x 4

1. Hole diameters listed are suggested hole saw diameters. 2. Special caution is required to some exceptional hole sizes shown in [ ].

Connect with the Best!

www.shurjoint.com

37
Copyright 2011 Shurjoint

Catalog 2011

MODEL

723 SADDLE-LET
Small Mechanical Tee

The Model 723 Saddle-Let is the ideal


outlet fitting for making direct connections to
sprinkler heads, drop nipples and or gauges.
No need for welding, just cut or drill a hole at

the desired outlet location.

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C


Class 150

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
32 x 15
1 x
32 x 20
1 x
32 x 25
1 x 1
40 x 15
1 x
40 x 20
1 x
40 x 25
1 x 1
50 x 15
2 x
50 x 20
2 x
50 x 25
2 x 1
65 x 15
2 x
65 x 20
2 x
65 x 25
2 x 1

Hole Dia.
+1.6, -0 / +0.063, -0
A
mm / in
mm / in
30
53.0
1.18
2.08
30
53.0
1.18
2.08
30
56.0
1.18
2.20
30
55.0
1.18
2.16
30
55.0
1.18
2.16
30
58.0
1.18
2.28
30
64.0
1.18
2.51
30
64.0
1.18
2.51
30
67.0
1.18
2.63
30
69.0
1.18
2.71
30
69.0
1.18
2.71
30
72.0
1.18
2.83

Dimensions
B
C
mm / in
mm / in
89.0
56.0
3.50
2.20
89.0
56.0
3.50
2.20
89.0
56.0
3.50
2.20
89.0
56.0
3.50
2.20
89.0
56.0
3.50
2.20
89.0
56.0
3.50
2.20
98.0
56.0
3.85
2.20
98.0
56.0
3.85
2.20
98.0
56.0
3.85
2.20
111.0
56.0
4.37
2.20
111.0
56.0
4.37
2.20
111.0
56.0
4.37
2.20

Take-Out,
T
mm / in
35.0
1.38
35.0
1.38
38.0
1.50
35.0
1.38
35.0
1.38
38.0
1.50
42.0
1.65
42.0
1.65
45.0
1.77
51.0
2.00
51.0
2.00
54.0
2.13

Bolt
Size
in
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt
3/8
U-Bolt

Bolt
Torque
N-m / Lb-Ft
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22
20-30
15-22

1. Hole diameters listed are suggested hole saw diameters. 2. *T: Take-out (Center of run to end of pipe to be engaged)

Hole Cutting

The method of pipe preparation requires the


cutting or drilling of a specified hole size on
the centerline of the pipe. Always use the
correct hole saw size as shown in the table
and never use a torch for cutting a hole.

Hole Sizes for 723 Saddle-let



Saddle- Let
Branch Size
15, 20, 25

, , 1

Hole Dimensions
Hole Saw Max dia.
Size
Allowed
30
32
113/16
1

unit: mm/in
Surface
Preparation
A
89
3

After the hole has been cut all rough edges


must be removed and the area within 5/8
(16mm) of the hole should be inspected to
ensure a clean smooth surface, free of any
indentations or projections that could affect
proper gasket sealing.

38
Copyright 2011 Shurjoint

Connect with the Best!

16mm ( " )

www.shurjoint.com

Weight
Kgs / Lbs
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.4
0.9
0.5
1.1

Catalog 2011

Performance Data Sheet - Ductile Iron Couplings on Carbon Steel & Stainless Steel Pipe
The following tables show maximum working pressures (CWP)
of Shurjoint ductile iron couplings and flange adapters used on

both carbon steel and stainless steel pipes. Shurjoint ductile iron

couplings can be used in conjunction with stainless steel pipe in


non-corrosive environment as the flow media does not come in direct
contact with the coupling housings but rather only the gasket.

unit: psi











Size

in
1
1
2
2
3
4
5
6
8

Model Z05 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
450
450
350
300
450
450
350
300
450
450
350
300

Size

in
1
1
2
2
3
4
5
6
8
10
12

Model Z07 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
750
750
750
600
750
750
750
600
750
750
750
600
750
750
750
600
750
750
750
600
750
750
750
600
750
750
750
500
700
700
700
400
600
600
600
350
500
500
500
300
400
400
400
250

Size

in
2
2
3
4
6
8
10
12

Model XH-1000 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
1500
1000
1000
750
1500
1000
1000
600
1500
1000
1000
600
1500
1000
1000
600
1500
1000
1000
450
900
800
800
300
900
800
800
300
900
800
800
200

Size

in
1
1
1
2
2
3
4
5
6
8
10
12

Model 7705 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
600
600
500
400
450
450
450
350
450
450
450
350
450
450
300
250
350
350
300
200
350
350
300
200

Size

in

1
1
1
2
2
3
4
5
6
8
10
12

Model 7707 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
1000
1000
750
600
1000
1000
750
600
1000
1000
750
600
1000
1000
750
600
1000
1000
750
600
1000
1000
750
600
1000
1000
750
600
1000
1000
750
600
1000
1000
750
500
1000
1000
700
450
800
800
600
350
800
800
550
300
800
800
500
300

Connect with the Best!

unit: psi

Sch. 7
250
250
250
250
250
200
175
175
150

Size

in
1
1
2
2
3
4
5
6
8

Model Z05 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
450
450
300
200
450
450
300
125
450
450
300
100

Sch. 5S
250
250
250
250
250
200
NR
NR
NR

Sch. 7
400
400
400
400
400
400
350
300
250
200
150

Size

in
1
1
2
2
3
4
5
6
8
10
12

Model Z07 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
750
750
700
500
750
750
700
500
750
750
700
500
750
750
700
500
750
750
700
500
750
750
700
400
750
750
600
300
700
700
500
200
600
600
400
150
500
500
300
100
400
400
250
100

Sch. 5S
300
300
300
300
300
250
NR
NR
NR
NR
NR

Sch. 7
NR
NR
NR
NR
NR
NR
NR
NR

Size

in
2
2
3
4
6
8
10
12

Model XH-1000 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
1500
1000
750
500
1500
1000
750
500
1500
1000
750
500
1500
1000
750
400
1500
1000
500
200
900
800
400
125
900
800
400
125
900
800
400
125

Sch. 5S
NR
NR
NR
NR
NR
NR
NR
NR

Sch. 7
300
300
300
300
300
300
300
250
250
200
175
175

Size

in
1
1
1
2
2
3
4
5
6
8
10
12

Model 7705 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
600
600
450
300
450
450
300
200
450
450
300
125
450
450
300
100
350
350
200
NR
350
350
200
NR

Sch. 5S
250
250
250
250
250
250
200
NR
NR
NR
NR
NR

Sch. 7
500
500
500
500
500
500
500
400
350
300
250
200
200

Size

in

1
1
1
2
2
3
4
5
6
8
10
12

Model 7707 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
750
750
700
450
750
750
700
450
750
750
700
450
750
750
700
450
750
750
700
450
750
750
700
450
750
750
700
450
750
750
700
400
750
750
600
300
750
750
500
200
600
600
450
150
600
600
400
125
600
600
400
125

Sch. 5S
325
325
325
325
325
325
325
250
NR
NR
NR
NR
NR

www.shurjoint.com

39
Copyright 2011 Shurjoint

Catalog 2011

unit: psi








Size

in
2
2
3
4
5
6

Model M-7 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
400
400
400
350
400
400
400
350

Size

in
1 x 1
2 x '1
2 x 2
3 x 2
3 x '2
4 x 2
4 x '2
4 x 3
5 x 4
6 x 3
6 x 4
8 x 6

Model 7706 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
300
400
400
400
300
400
400
400
300
400
400
400
300
400
400
400
300

Size

in
1
2
2
3
4
5
6
8
10
12

Model G28 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
250
300
300
300
250
300
300
300
250

Size

in
1 x *
2 x *
2 x *
3 x *
4 x *
6 x *

Model C-7 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
500
500
500
350
400
400
400
350

unit: psi

Sch. 7
300
300
300
300
250
250

Size

in
2
2
3
4
5
6

Model M-7 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
500
500
450
300
500
500
450
300
500
500
450
300
500
500
450
300
400
400
300
200
400
400
300
125

Sch. 5S
250
250
250
200
NR
NR

Sch. 7
300
300
300
300
300
300
300
250
250
200
175
175

Size

in
1 x 1
2 x '1
2 x 2
3 x 2
3 x '2
4 x 2
4 x '2
4 x 3
5 x 4
6 x 3
6 x 4
8 x 6

Model 7706 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
500
500
350
300
500
500
350
300
500
500
350
300
500
500
350
300
500
500
350
300
500
500
350
300
500
500
350
300
500
500
300
250
400
400
300
250
400
400
300
200
400
400
300
175
400
400
300
175

Sch. 5S
250
250
250
250
250
250
200
200
NR
NR
NR
NR

Sch. 7
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR

Size

in
'1
2
2.5
3
4
5
6
8
10
12

Model G28 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
175
300
300
250
150
300
300
250
150
300
300
200
NR
300
300
200
NR
300
300
200
NR

Sch. 5S
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR

Sch. 7
300
300
300
300
300
300

Size

in
1 x *
2 x *
2 x *
3 x *
4 x *
6 x *

Model C-7 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
500
500
350
300
500
500
350
300
500
500
350
300
500
500
350
300
500
500
350
300
400
400
300
300

Sch. 5S
250
250
250
250
250
250

* = all branch sizes, threaded and grooved

* = all branch sizes, threaded and grooved

Sch. 7
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR

Size

in
2
2
3
4
5
6
8
10
12
14
16
18
20
24

Model 7041 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
300
300
275
275
300
300
275
275
300
300
275
275
300
300
275
275
300
300
275
200
300
300
250
200
300
300
200
NR
300
300
200
NR
300
300
200
NR
250
250
125
NR
250
250
125
NR
250
250
125
NR
250
250
100
NR
250
250
100
NR

Sch. 5S
175
175
175
175
175
125
NR
NR
NR
NR
NR
NR
NR
NR

Sch. 7
NR
NR
NR
NR
NR
NR
NR
NR
NR

Size

in
2
2
3
4
5
6
8
10
12

Model 7043 on Stainless Steel Pipe


Cut-Grooved
Roll-Grooved
Sch. 80S
Sch. 40S
Sch. 40S
Sch. 10S
400
400
400
NR
400
400
400
NR
400
400
400
NR
300
300
300
NR
300
300
250
NR
300
300
200
NR
250
250
150
NR
250
250
150
NR
250
250
150
NR

Sch. 5S
NR
NR
NR
NR
NR
NR
NR
NR
NR

Size

in
2
2
3
4
5
6
8
10
12
14
16
18
20
24

Model 7041 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
300
300
300
250
300
300
300
250
300
300
300
250
300
300
300
250
300
300
300
250
300
300
300
250
300
300
300
200
300
300
300
200
300
300
300
200
300
300
300
200
300
300
300
175
300
300
300
175
300
300
300
150
300
300
300
150

Hydrostatic shell test: 450 psi (30 Bar) per ANSI B16.5

Size

in
2
2
3
4
5
6
8
10
12

Model 7043 on Carbon Steel Pipe


Cut-Grooved
Roll-Grooved
XS
STD
STD
Sch. 10
750
750
750
500
750
750
750
500
750
750
750
500
750
750
750
500
750
750
750
450
750
750
750
450
750
750
750
300
750
750
750
300
750
750
750
250

Hydrostatic shell test: 1125 psi (77 Bar) per ANSI B16.5

40
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Section 2
Cast & Wrought
Grooved Fittings
Shurjoint Grooved Fittings. ........................................................... 42
Flow Data / Friction Resistance. .................................................. 42
Ductile Iron Grooved Fittings
7110 / 7111 / 7112 / 7113 Elbows................................................... 43
7120 / 7135 / 7130 Tee, Cross, Lateral........................................... 44
7121 Reducing Tee............................................................................. 45
7150 / 7151 Concentric & Eccentric Reducers................................. 46
7160 / 7160T / 7160H / 7160P Caps............................................ 47
7110LR / 7111LR / 7137 / 7112G / 7110-B Elbows & True-Y... 48
901 / 903 / 7110DR / 7127 Elbows & Tee..................................... 49
7125 / 7150F / 7150M Bullhead Tee & Reducers.......................... 50
899 / 55 / 56 End-All & Nipples......................................................... 51
850 / 851 / 853 Sprinkler Hubs........................................................ 52
7114 / 7122 / 7133 Hydrant Elbow & Tees..................................... 53
Wrought Grooved Fittings
W110 / W110LR / W111LR / W120 / W160 / W121 Elbows & Tee...54
W150 / W151 / 57 / 58 / 59 Concentric & Eccentric Reducers, Nipples... 55
L90-3D / L60-3D / L45-3D / L30-3D / L22-3D / L11-3D Elbows..... 56
L90-5D / L60-5D / L45-5D / L30-5D / L22-5D / L11-5D Elbows..... 57
L90-6D / L60-6D / L45-6D / L30-6D / L22-6D / L11-6D Elbows..... 57
Extra Heavy Grooved Fittings
10EP / 11EP / 20EP / 35EP / 22EP Elbows, Tees & Cross....... 58

Connect with the Best!

Catalog 2011

www.shurjoint.com

Catalog 2011

Shurjoint Grooved Fittings


Shurjoint offers a wide range of grooved-end fittings in sizes through 24
(600mm). Fittings are available in a number of styles and configurations
to support a variety of applications. Shurjoint grooved-end fittings are
manufactured and designed to meet ASTM F1548 and ANSI/AWWA C606
requirements for use with grooved mechanical couplings conforming to
ASTM F1476. For sizes not specified in these standards, please refer to
applicable groove specifications shown in this catalog.
Pressure-Temperature Rating

Size

Nom.
Rating

1 6

Class 300
(25 150)
8 12

Class 250
(200 300)
14 24

Class 150
(250 600)

welded steel of the same or equivalent

Working Pressure Max. Service


(STD, Roll-grooved) Temperature
750 psi @100F
52 Bar @38C
400 psi @100F
28 Bar @38C
300 psi @100F
20 Bar @38C

EPDM:
230F / 110C
Nitrile:
180F / 82C

grade. Fittings are painted orange or red,


or as an option can be supplied hot-dip
galvanized or epoxy coated.

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Rubber Lined Fittings

Shurjoint ductile iron grooved end fittings


are also available with rubber lining for
abrasive services. Contact Shurjoint for
further information.

For abrasive services

For abrasive and


corrosive services

Most fittings are provided in ductile iron


conforming to ASTM A536 Gr. 65-45-12 and
or ASTM A395 Gr. 65-45-15. Some styles
and sizes larger than 14 (350mm) are
fabricated from carbon steel pipe to ASTM
A53 Gr. B or fabricated of segmentally

Flow Data / Frictional Resistance

Expressed as equivalent length of straight pipe




Nominal
Pipe
Pipe Wall
#7110 90
#901 90

Size
O.D.
Thickness
Std. Radius
Short. Radius

mm / in
mm / in
mm / in
meters / feet
meters / feet

25
33.4
3.4
0.5
---

1
1.315
0.133
1.7
---

32
42.2
3.6
0.8
0.8

1
1.660
0.140
2.5
2.5

40
48.3
40
1.1
1.1

1
1.900
0.154
3.5
3.5

50
60.3
5.2
1.2
1.2

2
2.375
0.203
4.0
4.0

65
73.0
5.0
1.4
1.4

2
2.875
0.197
4.5
4.5

80
88.9
6.3
1.5
1.5

3
3.500
0.237
5.0
5.0

100
114.3
5.6
2.0
2.0

4
4.500
0.220
6.7
6.7

125
141.3
6.6
2.3
2.3

5
5.563
0.258
7.5
7.5

150
168.3
7.1
2.7
2.7

6
6.625
0.280
9.0
9.0

200
219.1
8.2
4.0
4.0

8
8.625
0.322
13.0
13.0

250
273.0
8.8
5.2
---

10
10.750
0.365
17.0
---

300
323.9
9.5
6.1
---

12
12.750
0.375
20.0
---

Elbows
#7110LR 90
#7111 45
#7111LR 45
1 D. LR
Std. Radius
1 D. LR
meters / feet
meters / feet
meters / feet
---
0.2
---
---
0.8
---
---
0.3
---
---
1.0
---
---
0.5
---
---
1.5
---
0.8
0.5
0.3
2.5
1.7
1.1
0.9
0.6
0.4
2.9
2.0
1.4
1.2
0.8
0.5
3.8
2.5
1.5
1.5
0.9
0.6
5.0
3.0
2.1
1.8
1.2
0.6
6.0
4.0
2.5
2.3
1.4
0.9
7.5
4.5
3.0
3.0
2.0
1.2
9.8
6.5
4.0
3.7
2.5
1.5
12.0
8.3
5.0
4.4
3.1
1.8
14.5
10.0
6.0

Tees
#7120
#903
Branch
Branch
meters / feet
meters / feet
1.3
--4.2
--1.4
1.4
4.7
4.7
2.0
2.0
6.5
6.5
2.6
2.6
8.5
8.5
3.1
3.1
10.0
10.0
3.7
3.7
12.0
12.0
4.6
4.6
15.0
15.0
5.8
5.8
19.0
19.0
6.7
6.7
22.0
22.0
10.1
10.1
33.0
33.0
12.5
--41.0
--14.9
--49.0
---

The values listed in this table express the frictional resistance of representative Shurjoint fittings as equivalent feet (meters) of straight pipe. For the branch of a tee that is reduced in size, use the value that
corresponds to the branch size. For example, the branch value of a 4 x 4 x 3 tee is 12.8 feet (3.9 meters). For fittings not listed in this table, the equivalent length of straight pipe can be estimated from the
data provided. For example, the flow resistance of a 22 elbow is approximately one half that of a 45 elbow.

42
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

MODEL

Catalog 2011

MODEL

7110 90 elbow 7111 45 elbow


7112 22- elbow 7113 11- elbow
Shurjoint ductile iron grooved-end fittings
are made of ductile iron per ASTM A536
Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturers
standard. See page 54 for wrought steel
grooved-end fittings.

C-E

C-E

7110
90 Elbow


Nominal

Size

mm / in

25

1

32

1

40

1

50

2

65

2


76.1mm


80

3


101.6mm


100

4


108.0mm


125

5


133.0mm



139.7mm


150

6


159.0mm



165.1mm


200

8

250

10

300

12


200JIS



250JIS



300JIS


350

14

400

16

450

18

500

20

600

24

Pipe
O. D.
mm / in
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
101.6
4.000
114.3
4.500
108.0
4.250
141.3
5.563
133.0
5.250
139.7
5.500
168.3
6.625
159.0
6.250
165.1
6.500
219.1
8.625
273.0
10.750
323.9
12.750
216.3
8.516
267.4
10.528
318.5
12.539
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000

#7110 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
57
0.3
2.25
0.7
70
0.5
2.75
1.1
70
0.6
2.75
1.3
83
0.9
3.25
2.0
95
1.2
3.75
2.6
95
1.4
3.75
3.1
108
2.0
4.25
4.3
114
2.5
4.50
5.6
127
3.1
5.00
6.9
127
2.5
5.00
5.5
140
5.0
5.50
11.0
140
4.1
5.50
9.0
140
4.3
5.50
9.5
165
5.8
6.50
12.8
165
6.0
6.50
13.2
165
5.7
6.50
12.5
197
13.0
7.75
28.7
229
24.1
9.00
53.1
254
36.7
10.00
81.0
197
12.4
7.75
27.2
229
24.0
9.00
52.8
254
35.0
10.00
77.0
280
35.1
11.00
77.5
305
43.0
12.00
94.6
394
83.5
15.50
184.0
438
118.5
17.25
261.2
508
185.0
20.00
407.9

Connect with the Best!

C-E
7111
45 Elbow

#7111 45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
45
0.2
1.75
0.5
45
0.3
1.75
0.7
45
0.4
1.75
0.9
51
0.7
2.00
1.5
57
0.9
2.25
2.0
57
0.9
2.25
2.1
64
1.3
2.50
2.9
---
---
---
---
76
2.0
3.00
4.4
76
2.0
3.00
4.4
83
3.0
3.25
6.6
83
2.7
3.25
5.9
83
2.9
3.25
6.4
89
4.0
3.50
8.9
89
3.8
3.50
8.4
89
4.0
3.50
8.9
108
8.6
4.25
19.0
121
15.5
4.75
34.2
133
22.5
5.25
49.5
108
8.4
4.25
18.5
121
15.5
4.75
34.2
133
22.5
5.25
49.5
152
22.0
6.00
48.4
184
44.0
7.25
96.8
203
46.6
8.00
102.5
229
54.5
9.00
120.2
280
83.5
11.00
184.1

7112
22 Elbow
#7112 22 Elbow
C - E
Weight
mm / in
Kgs / Lbs
---
---
---
---
---
---
---
---
45
0.6
1.75
1.3
48
0.8
1.88
1.8
51
1.0
2.01
2.2
51
1.0
2.01
2.2
57
1.4
2.25
3.1
---
---
---
---
73
2.0
2.88
4.4
---
---
---
---
73
3.1
2.88
6.8
---
---
---
---
73
2.9
2.88
6.5
79
5.0
3.12
11.0
---
---
---
---
79
5.0
3.12
11.0
98
10.0
3.88
22.0
111
17.7
4.38
38.9
---
19.5
---
42.9
98
10.0
3.88
22.0
111
17.7
4.38
38.9
---
---
---
---
---
21.0
---
46.2
---
22.0
---
48.4
---
---
---
---
---
---
---
---
---
---
---
---

www.shurjoint.com

C-E
7113
11 Elbow
#7113 11 Elbow
C - E
Weight
mm / in
Kgs / Lbs
---
-----
-----
-----
-----
-----
--35
0.4
1.38
1.0
38
0.7
1.50
1.6
38
0.8
1.50
1.7
38
0.8
1.50
1.8
---
-----
--45
1.0
1.75
2.2
---
-----
-----
-----
-----
-----
-----
-----
--51
2.5
2.00
5.5
---
-----
--51
2.5
2.00
5.5
51
5.5
2.00
12.1
54
10.0
2.13
22.1
57
12.4
2.25
27.3
---
-----
--54
10.0
2.13
22.1
57
12.4
2.25
27.3
---
-----
-----
-----
-----
-----
-----
-----
-----
-----
---

43
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7120 tee
7135 cross
7130 45 lateral
Shurjoint ductile iron grooved-end fittings
are made of ductile iron per ASTM A536
Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturers
standard. See page 54 for wrought steel
grooved-end fittings.

-L

C-LE

C-SE

C-E
C-E

C-E
7135 Cross

7120 Tee

Nominal

Size

mm / in

25

1

32

1

40

1

50

2

65

2


76.1mm


80

3

100

4


108.0mm


125

5


133.0mm



139.7mm


150

6

150

6


165.1mm


200

8

250

10

300

12


200JIS



250JIS



300JIS


350

14

400

16

44
Copyright 2011 Shurjoint

Pipe
O. D.
mm / in
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
108.0
4.250
141.3
5.563
133.0
5.250
139.7
5.500
168.3
6.625
159.0
6.250
165.1
6.500
219.1
8.625
273.0
10.750
323.9
12.750
216.3
8.516
267.4
10.528
318.5
12.539
355.6
14.000
406.4
16.000

C - E
mm / in
57
2.25
70
2.75
70
2.75
83
3.25
95
3.75
95
3.75
108
4.25
127
5.00
127
5.00
140
5.50
140
5.50
140
5.50
165
6.50
165
6.50
165
6.50
197
7.75
229
9.00
254
10.00
197
7.75
229
9.00
254
10.00
280
11.00
305
12.00

#7120 Tee
Weight
Kgs / Lbs
0.4
0.9
0.7
1.5
0.9
2.0
1.3
2.9
2.2
4.8
2.3
5.1
3.1
6.8
4.5
9.9
4.1
9.0
6.5
14.3
6.0
13.2
6.5
14.3
10.0
22.0
8.6
18.9
9.4
20.8
20.0
44.0
31.0
68.2
43.9
96.7
20.0
44.0
31.0
68.2
43.9
96.7
52.0
114.6
68.0
149.9

Connect with the Best!

C - E
mm / in
---
---
---
---
---
---
83
3.25
95
3.75
95
3.75
108
4.25
127
5.00
---
---
140
5.50
---
---
140
5.50
165
6.50
---
---
165
6.50
197
7.75
---
---
---
---
197
7.75
---
---
---
---
---
---
---
---

7130
45 Lateral

#7135 Cross
Weight
C - LE
Kgs / Lbs
mm / in
---
---
---
---
---
---
---
---
---
---
---
---
1.2
178
2.7
7.00
3.0
197
6.7
7.75
3.0
197
6.7
7.75
3.1
216
6.8
8.50
5.2
267
11.5
10.50
---
---
---
---
5.9
318
13.0
12.50
---
---
---
---
5.9
318
13.0
12.50
14.5
356
32.0
14.00
---
---
---
---
14.5
356
32.0
14.00
20.0
457
44.1
18.00
---
521
---
20.50
---
584
---
23.00
20.0
457
44.1
18.00
---
521
---
20.50
---
584
---
23.00
---
---
---
---
---
---
---
---

#7130 45 Lateral
C - SE
Weight
mm / in
Kgs / Lbs
---
-----
-----
-----
-----
-----
--70
2.0
2.75
4.4
76
2.8
3.00
6.2
76
2.8
3.00
6.2
83
4.2
3.25
9.2
95
8.0
3.75
17.6
---
-----
--102
12.5
4.00
27.5
---
-----
--102
12.5
4.00
27.5
114
18.5
4.50
40.7
---
-----
--114
18.5
4.50
40.7
152
32.0
6.00
70.4
165
63.0
6.50
138.9
178
91.5
7.00
201.7
152
32.0
6.00
70.4
165
63.0
6.50
138.9
178
91.5
7.00
201.7
---
-----
-----
-----
---

www.shurjoint.com

Catalog 2011

MODEL

7121 reducing tee


Shurjoint ductile iron grooved-end fittings
are made of ductile iron per ASTM A536
Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturers
standard. See page 54 for wrought steel

C-E
7121 Reducing Tee

Nominal

Size

mm / in

50 x 50 x 40

2 x 2 x1

65 x 65 x 25

2 x 2 x 1

65 x 65 x 40

2 x 2 x 1

65 x 65 x 50

2 x2 x 2

65 x 65 x 50

2 x 2 x 2

80 x 80 x 25

3 x 3 x 1

80 x 80 x 40

3 x 3 x 1

80 x 80 x 50

3 x 3 x 2

80 x 80 x 65

3 x 3 x 2

80 x 80 x 65

3 x 3 x 2
100 x 100 x 25

4 x 4 x 1
100 x 100 x 50

4 x 4 x 2
100 x 100 x 65

4 x 4 x 2


100 x 100 x 76.1mm

100 x 100 x 80

4 x 4 x 3
125 x 125 x 50

5 x 5 x 2
125 x 125 x 100

5 x 5 x 4
150 x 150 x 50

6 x 6 x 2
150 x 150 x 65

6 x 6 x 2

Pipe
O. D.
mm / in
60.3 x 60.3 x 48.3
2.375 x 2.375 x 1.900
73.0 x 73.0 x 33.4
2.875 x 2.875 x 1.315
76.1 x 76.1 x 48.3
3.000 x 3.000 x 1.900
73.0 x 73.0 x 60.3
2.875 x 2.875 x 2.375
76.1 x 76.1 x 60.3
3.000 x 3.000 x 2.375
88.9 x 88.9 x 33.4
3.500 x 3.500 x 1.315
88.9 x 88.9 x 48.3
3.500 x 3.500 x 1.900
88.9 x 88.9 x 60.3
3.500 x 3.500 x 2.375
88.9 x 88.9 x 73.0
3.500 x 3.500 x 2.875
88.9 x 88.9 x 76.1
3.500 x 3.500 x 3.000
114.3 x 114.3 x 33.4
4.500 x 4.500 x 1.315
114.3 x 114.3 x 60.3
4.500 x 4.500 x 2.375
114.3 x 114.3 x 73.0
4.500 x 4.500 x 2.875
114.3 x 114.3 x 76.1
4.500 x 4.500 x 3.000
114.3 x 114.3 x 88.9
4.500 x 4.500 x 3.500
141.3 x 141.3 x 60.3
5.563 x 5.563 x 2.375
141.3 x 141.3 x 114.3
5.563 x 5.563 x 4.500
168.3 x 168.3 x 60.3
6.625 x 6.625 x 2.375
168.3 x 168.3 x 73.0
6.625 x 6.625 x 2.875

Standard
C - E
mm / in
83
3.25
95
3.75
95
3.75
95
3.75
95
3.75
108
4.25
108
4.25
108
4.25
108
4.25
108
4.25
95
3.75
127
5.00
127
5.00
127
5.00
127
5.00
140
5.50
140
5.50
165
6.50
165
6.50

Threaded Br.
C - E
mm / in
83
3.25
95
3.75
95
3.75
95
3.75
95
3.75
108
4.25
108
4.25
108
4.25
108
4.25
108
4.25
95
3.75
127
5.00
127
5.00
127
5.00
127
5.00
140
5.50
140
5.50
165
6.50
165
6.50

Connect with the Best!

Weight
Kgs / Lbs
1.2
2.6
1.7
3.8
1.8
3.9
2.0
4.4
2.0
4.4
2.5
5.5
2.4
5.2
2.8
6.2
2.8
6.2
2.8
6.2
4.0
8.9
4.0
8.8
4.3
9.5
4.3
9.5
4.3
9.4
5.6
12.4
6.2
13.6
8.0
17.6
8.5
18.7

C-E

C-E

grooved-end fittings.

C-E
7121 Reducing Tee (Threaded)


Nominal
Pipe

Size
O. D.

mm / in
mm / in
150 x 150 x 80
168.3 x 168.3 x 88.9

6 x 6 x 3
6.625 x 6.625 x 3.500
150 x 150 x 100
168.3 x 168.3 x 114.3

6 x 6 x 4
6.625 x 6.625 x 4.500
165.1 x 165.1 x 50
165.1 x 165.1 x 60.3

6 x 6 x 2
6.500 x 6.500 x 2.375


165.1 x 165.1 x 76.1
165.1 x165.1 x 76.1

6.500 x 6.500 x 3.000
165.1 x 165.1 x 80
165.1 x 165.1 x 88.9

6 x 6 x 3
6.500 x 6.500 x 3.500
165.1 x 165.1 x 100
165.1 x 165.1 x 114.3

6 x 6 x 4
6.500 x 6.500 x 4.500

200 x 200 x50
219.1 x 219.1 x 60.3

8 x 8 x 2
8.625 x 8.625 x 2.375
200 x 200 x 80
219.1 x 219.1 x 88.9

8 x 8 x 3
8.625 x 8.625 x 3.500
200 x 200 x 100
219.1 x 219.1 x 114.3

8 x 8 x 4
8.625 x 8.625 x 4.500
200 x 200 x 150
219.1 x 219.1 x 168.3

8 x 8 x 6
8.625 x 8.625 x 6.625
250 x 250 x 100
273.0 x 273.0 x 114.3

10 x 10 x 4
10.750 x 10.750 x 4.500
250 x 250 x 150
273.0 x 273.0 x 168.3

10 x 10 x 6
10.750 x 10.750 x 6.625
250 x 250 x 200
273.0 x 273.0 x 219.1

10 x 10 x 8
10.750 x 10.750 x 8.625
300 x 300 x 80
323.9 x 323.9 x 88.9

12 x 12 x 3
12.750 x 12.750 x 3.500
300 x 300 x 100
323.9 x 323.9 x114.3

12 x 12 x 4
12.750 x 12.750 x 4.500
300 x 300 x 150
323.9 x 323.9 x 168.3

12 x 12 x 6
12.750 x 12.750 x 6.625
300 x 300 x 200
323.9 x 323.9 x 219.1

12 x 12 x 8
12.750 x 12.750 x 8.625
300 x 300 x 250
323.9 x 323.9 x 273.0

12 x 12 x 10
12.750 x 12.750 x 10.750

Standard
C - E
mm / in
165
6.50
165
6.50
165
6.50
165
6.50
165
6.50
165
6.50
197
7.75
197
7.75
197
7.75
197
7.75
229
9.00
229
9.00
229
9.00
254
10.00
254
10.00
254
10.00
254
10.00
254
10.00

www.shurjoint.com

Threaded Br.
C - E
mm / in
165
6.50
165
6.50
165
6.50
165
6.50
165
6.50
165
6.50
197
7.75
197
7.75
197
7.75
---
---
229
9.00
---
---
---
---
254
10.00
254
10.00
---
---
---
---
---
---

Weight
Kgs / Lbs
9.2
20.2
8.8
19.4
8.0
17.6
8.5
18.7
9.2
20.2
8.8
19.4
14.8
32.5
15.5
34.2
20.0
44.0
21.0
46.2
28.5
62.8
30.0
66.0
31.5
69.3
40.0
88.1
41.0
90.4
38.0
83.6
38.0
83.6
40.0
88.0

45
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7150 CONCENTRIC REDUCER


7151 ECCENTRIC REDUCER
Shurjoint ductile iron grooved-end fittings
are made of ductile iron per ASTM A536
Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturers
standard. See page 55 for wrought steel
grooved-end fittings.

E-E
7150 Conc.
Reducer
Nominal

Size
mm / in

32 x 25

1 x 1

40 x 25

1 x 1

40 x 32
1 x 1

50 x 25

2 x 1

50 x 32

2 x 1

50 x 40

2 x 1

65 x 50

2 x 2


76.1mm x 50


80 x 25

3 x 1

80 x 32

3 x 1

80 x 40

3 x 1

80 x 50

3 x 2

80 x 65

3 x 2.5

80 x 65

3 x 2
100 x 50

4 x 2
100 x 65

4 x 2


100 x 76.1mm

100 x 80

4 x 3
125 x 100

5 x 4
150 x 50

6 x 2
150 x 65

6 x 2
150 x 80

6 x 3
150 x 100

6 x 4
150 x 125

6 x 5


165.1mm x 50

165.1mm
x 76.1mm

46
Copyright 2011 Shurjoint

Pipe
O. D.
mm / in
42.2 x 33.4
1.660 x 1.315
48.3 x 33.4
1.900 x 1.315
48.3 x 42.2
1.900 x 1.660
60.3 x 33.4
2.375 x 1.315
60.3 x 42.2
2.375 x 1.660
60.3 x 48.3
2.375 x 1.900
73.0 x 60.3
2.875 x 2.375
76.1 x 60.3
3.000 x 2.375
88.9 x 33.4
3.500 x 1.315
88.9 x 42.2
3.500 x 1.660
88.9 x 48.3
3.500 x 1.900
88.9 x 60.3
3.500 x 2.375
88.9 x 73.0
3.500 x 2.875
88.9 x 76.1
3.500 x 3.000
114.3 x 60.3
4.500 x 2.375
114.3 x 73.0
4.500 x 2.875
114.3 x 76.1
4.500 x 3.000
114.3 x 88.9
4.500 x 3.500
141.3 x 114.3
5.563 x 4.500
168.3 x 60.3
6.625 x 2.375
168.3 x 73.0
6.625 x 2.875
168.3 x 88.9
6.625 x 3.500
168.3 x 114.3
6.625 x 4.500
168.3 x 141.3
6.625 x 5.563
165.1 x 60.3
6.500 x 2.375
165.3 x 76.1
6.5.00 x 3.000

#7150 Conc. Reducer


E - E
Weight
mm / in
Kgs / Lbs
64
0.20
2.50
0.44
64
0.23
2.50
0.51
64
0.28
2.50
0.62
64
0.37
2.50
0.82
64
0.33
2.50
0.73
64
0.35
2.50
0.77
64
0.59
2.50
1.30
64
0.59
2.50
1.30
64
0.6
2.50
1.3
64
0.6
2.50
1.3
64
0.6
2.50
1.5
64
0.6
2.50
1.3
64
0.6
2.50
1.3
64
0.6
2.50
1.3
76
0.91
3.00
2.01
76
0.98
3.00
2.16
76
1.03
3.00
2.27
76
1.0
3.00
2.2
89
1.61
3.50
3.55
102
1.9
4.00
4.2
102
2.0
4.00
4.4
102
2.0
4.00
4.4
102
2.1
4.00
4.6
102
2.5
4.00
5.5
102
1.9
4.00
4.2
102
1.9
4.00
4.2

Connect with the Best!

#7151 Ecc. Reducer


E - E
Weight
mm / in
Kgs / Lbs
---
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
--89
0.65
3.50
1.44
89
0.72
3.50
1.58
---
-----
-----
-----
-----
-----
--89
1.0
3.50
2.2
89
1.0
3.50
2.2
89
1.0
3.50
2.2
102
1.29
4.00
2.85
102
1.5
4.00
3.3
102
1.5
4.00
3.3
102
1.34
4.00
2.95
102
2.8
4.00
6.17
102
2.0
4.00
4.41
---
3.07
---
6.77
102
3.5
4.00
7.7
102
2.65
4.00
5.84
102
4.5
4.00
9.9
102
2
4.00
4.41
---
-----
---

Nominal
Size
mm / in
200 x 80
8 x 3
200 x 100
8 x 4
200 x 150
8 x 6
250 x 100
10 x 4
250 x 150
10 x 6
250 x 200
10 x 8
300x150
12 x 6
300 x 200
12 x 8
300 x 250
12 x 10
350 x 200
14 x 8
350 x 250
14 x 10
350 x 300
14 x 12
400 x 200
16 x 8
400 x 300
16 x 12
400 x 350
16 x 14
450 x 300
18 x 12
450 x 350
18 x 14
450 x 400
18 x 16
500 x 300
20 x 12
500 x 400
20 x 16
500 x 450
20 x 18
600 x 250
24 x 10
600 x 300
24 x 12
600 x 400
24 x 16
600 x 450
24 x 18
600 x 500
24 x 20

Pipe
O. D.
mm / in
219.1 x 88.9
8.625 x 3.500
219.1 x 114.3
8.625 x 4.500
219.1 x 168.3
8.625 x 6.625
273.0 x 114.3
10.750 x 4.500
273.0 x 168.3
10.750 x6.625
273.0 x 219.1
10.750 x 8.625
323.9 x 168.3
12.750 x 6.625
323.9 x 219.1
12.750 x 8.625
323.9 x 273.0
12.750 x 10.750
355.6 x 219.1
14.000 x 8.625
355.6 x 273.0
14.000 x 10.750
355.6 x 323.9
14.000 x 12.750
406.4 x 219.1
16.000 x 8.625
406.4 x 323.9
16.000 x 12.750
406.4 x 355.6
16.000 x 14.000
457.2 x 323.9
18.000 x 12.750
457.2 x 355.6
18.000 x 14.000
457.2 x 406.4
18.000 x 16.000
508.0 x 406.4
20.000 x 16.000
508.0 x 406.4
20.000 x 18.000
508.0 x 457.2
20.000 x 16.000
609.6 x 273.0
24.000 x 10.750
609.6 x 323.9
24.000 x 12.750
609.6 x 406.4
24.000 x 16.000
609.6 x 457.2
24.000 x 18.000
609.6 x 508.0
24.000 x 20.000

E-E

7151
Ecc. Reducer
#7150 Conc. Reducer
E - E
Weight
mm / in
Kgs / Lbs
127
4.3
5.00
9.48
127
5.1
5.00
11.2
127
5.2
5.00
11.4
152
9.0
6.00
19.8
152
9.0
6.00
19.8
152
9.5
6.00
20.9
178
14.0
7.00
30.87
178
14.0
7.00
30.8
178
13.66
7.00
30.12
203
19.0
8.00
41.8
330
23.59
13.00
52.01
330
23.0
13.00
50.71
229
23.7
9.00
52.25
356
31.0
14.00
68.34
356
29.0
14.02
63.93
241
35.5
9.50
78.1
381
36.5
15.00
80.47
381
31.27
15.00
68.94
381
43.0
15.00
94.6
508
46.0
20.00
101.41
254
46.0
10.00
101.2
305
36.0
12.00
79.2
305
70.0
12.00
154.0
305
59.5
12.00
131.18
508
48.5
20.00
106.92
508
71.0
20.00
156.53

www.shurjoint.com

#7151 Ecc. Reducer


E - E
Weight
mm / in
Kgs / Lbs
---
-----
--127
5.26
5.00
11.60
127
5.46
5.00
12.03
152
12.0
6.00
26.4
152
11.5
6.00
25.3
178
12.17
7.00
26.83
178
18.0
7.00
39.6
178
18.5
7.00
40.79
178
20.0
7.00
44.10
---
-----
--330
21.0
13.00
46.30
330
26.5
13.00
58.4
---
-----
--356
31.0
14.02
68.34
356
36.5
14.02
80.47
---
-----
--381
39.5
15.00
87.0
381
31.00
15.00
68.34
---
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
---

MODEL

MODEL

Catalog 2011

MODEL

7160T TRANSITION CAP 7160H domed end CAP

7160 END CAP

Shurjoint Model 7160T is an ideal transition

Shurjoint 7160H end caps are cast of ductile

fitting when a large reduction is required and

iron and are designed to withstand pressure

can be used in place of more costly reducers

evenly over the entire spherical surface. The

or swaged nipples. In addition the 7160T can

Model 7160H End Cap is designed for use

serve as a drain fitting.

on 10 - 24 mechanical piping applications.

E-E
1 ~ 12

Pipe
O.D.
mm / in
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
108.0
4.250
141.3
5.563
133.0
5.250
139.7
5.500
168.3
6.625
159.0
6.250
165.1
6.500
219.1
8.625
273.0
10.750
323.9
12.750
216.3
8.516
267.4
10.528
318.5
12.539

#7160 End Cap


E - E
Weight
mm / in
Kgs / Lbs
22
0.1
0.87
0.2
25
0.15
1.00
0.33
25
0.2
1.00
0.4
25
0.3
1.00
0.7
25
0.4
1.00
0.9
25
0.4
1.00
0.9
25
0.7
1.00
1.5
25
1.0
1.00
2.2
25
1.1
1.00
2.4
25
1.7
1.00
3.7
25
1.7
1.00
3.7
25
1.7
1.00
3.7
25
2.7
1.0
5.96
25
2.3
1.00
5.1
25
2.7
1.00
5.96
30
4.6
1.18
10.14
32
7.0
1.25
15.4
32
10.0
1.25
22.0
30
4.6
1.18
10.1
32
7.0
1.25
15.4
32
10.0
1.25
22.0

SW: segment-welded steel.

MODEL

7160P END CAP w/PLUG


Nominal Size
Grooved x Threaded

mm / in

50 x 25

2 x 1

50 x 32

2 x 1

65 x 25

2 x 1

65 x 32

2 x 1

65 x 40

2 x 1

80 x 25

3 x 1

80 x 32

3 x 1

80 x 40

3 x 1

80 x 50

3 x 2

100 x 25

4 x 1

100 x 32

4 x 1

100 x 40

4 x 1

100 x 50

4 x 2

150 x 25

6 x 1

150 x 32

6 x 1

150 x 40

6 x 1

150 x 50

6 x 2


Nominal

Size

mm / in

50

2

65

2


76.1 mm


80

3

100

4

125

5

Connect with the Best!

L
mm / in
23.8
0.94
23.8
0.94
23.8
0.94
23.8
0.94
23.8
0.94
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0
25.4
1.0

Pipe
O.D.
mm / in
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
141.3
5.563

7160T

Weight
Kgs / Lbs
0.25
0.55
0.25
0.55
0.44
0.97
0.35
0.77
0.30
0.70
0.65
1.43
0.65
1.43
0.60
1.30
0.60
1.33
0.95
2.09
0.95
2.09
0.90
2.00
0.90
1.98
2.50
5.52
2.50
5.52
2.50
5.50
2.50
5.50

7160P
Plug Size
mm / in
15

15

15

15
0.5
25
1
25
1

E-E

Nominal

Size
mm / in

25

1

32

1

40

1

50

2

65

2


76.1 mm


80

3

100

4


108 mm


125

5


133 mm



139.7 mm


150

6


159.0 mm



165.1 mm


200

8

250

10

300

12


200 JIS



250 JIS



300 JIS

10 ~ 24
Nominal

Size
mm / in

250

10

300

12

350

14

400

16

450

18

500

20

550

22

600

24

Pipe
O.D.
mm / in
273.0
10.750
323.90
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
558.8
22.000
609.6
24.000


Nominal

Size

mm / in


139.7 mm


150

6


165.1 mm


200

8

250

10

300

12

www.shurjoint.com

#7160H Domed End Cap


E - E
Weight
mm / in
Kgs / Lbs
76.1
5.5
3.00
12.1
76.1
7.4
3.00
16.3
102
11.95
4.00
26.35
102
14.5
4.00
31.97
127
17.8
5.00
39.24
152
24.5
6.00
53.9
152
44.0
6.00
97.0
152
34.5
6.00
75.9

Pipe
O.D.
mm / in
139.7
5.500
168.3
6.625
165.1
6.500
219.1
8.625
273.0
10.750
323.9
12.750

7160P
Plug Size
mm / in
25
1
25
1
25
1
40
1
40
1
40
1

47
Copyright 2011 Shurjoint

Catalog 2011

MODELS


Nominal

Size

mm / in

50

2

65

2


76.1 mm


80

3

100

4

125

5


139.7 mm


150

6


165.1 mm


200

8

250

10

300

12

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
141.3
5.563
139.7
5.500
168.3
6.625
165.1
6.500
219.1
8.625
273.0
10.750
323.9
12.750

7110LR
LR 90 Elbow, 1.5D

#7110LR 1.5D LR 90 Elbow


C - E
mm / in
Kgs / Lbs
111
1.1
4.38
2.4
127
1.8
5.0
4.0
127
1.8
5.0
4.0
149
1.8
5.88
4.0
191
4.7
7.50
10.3
241
8.3
9.50
18.3
241
8.3
9.50
18.3
273
11.5
10.75
25.3
273
11.5
10.75
25.3
362
23.0
14.25
50.7
438
42.2
17.25
73.0
521
71.5
20.50
157.6

C-SE

C-E

C-E

-L

7110LR 1.5D 90 elbow


7111LR 1.5D 45 elbow
7137 TRUE-Y

7137
True-Y

7111LR
LR 45 Elbow, 1.5D

#7111LR 1.5D LR 45 Elbow


C - E
C - LE
mm / in
Kgs / Lbs
mm / in
70
0.8
83
2.75
1.8
3.25
76
1.4
95
3.00
3.1
3.75
76
1.45
95
3.00
3.20
3.75
86
1.8
108
3.38
3.97
4.25
102
3.5
127
4.00
7.7
5.00
127
4.6
140
5.0
10.14
5.50
127
4.6
140
5.0
10.14
5.50
140
8.2
165
5.50
18.0
6.50
140
8.2
165
5.50
18.0
6.50
184
16.0
197
7.25
35.27
7.75
216
36.1
229
8.50
78.59
9.00
254
33.5
254
10.00
73.86
10.00

#7137 TRUE-Y
C - SE
mm / in
70
2.75
76
3.00
76
3.00
83
3.25
95
3.75
102
4.00
102
4.00
114
4.50
114
4.50
152
6.00
165
6.50
178
7.00

Kgs / Lbs
1.1
2.5
1.7
3.75
1.8
3.97
2.50
5.51
4.7
10.43
5.3
11.60
6.8
14.96
8.9
19.62
8.9
19.62
15.6
34.33
25.5
56.22
36.0
79.37

MODELS

7112G Goose Neck


22- Elbow

Two model 7112G elbows in combination


with a coupling will serve as a universal
joint and is ideal for instances where a pipe

MODEL

7110-B 90 ELBOW With Base Support


The Model 7110-B is a ductile iron 90

riser system. An anchor can be placed in

grooved-end elbow with base support,

conjunction with the base to support the

designed for installation at the bottom of a

weight of the pipe, coupling and fluid.

line is in need of a slight adjustment during

C-E
C-E

make-up.

U
Nominal

Size
mm / in

40

1

50

2

65

2

80

3

100

4

125

5

150

6

200

8


200JIS

48
Copyright 2011 Shurjoint

Pipe
7112G 22 Elbows
O.D.
E - E
Weight
mm / in
mm / in
Kgs / Lbs
48.3 95 G
0.6
1.900
3.75
1.3
60.3
95 G
0.8
2.375
3.75
1.3
73.0
102 G
1.0
2.875
4.00
2.2
88.9
114 G
1.4
3.500
4.50
3.1
114.3
127 G
2.0
4.500
5.00
4.4
141.3
127 G
3.3
5.563
5.00
7.3
168.3
159 G
5.0
6.625
6.25
11.0
219.1
197 G
10.0
8.625
7.75
22.0
216.3
197 G
10.0
8.516
7.75
22.0

E-E

Nominal

Size
mm / in

80

3

100

4

150

6

200

8

250

10

300

12

Connect with the Best!

Pipe
Dimensions
O. D.
C - E
H U
T
S
M
mm / in
mm / in
mm / in
mm / in
mm / in
mm / in
mm / in
88.9
108
124
13
14
127
99
3.500
4.25
4.88
0.50
0.56
5.00
3.88
114.3
127
140
13
16
152
121
4.500
5.00
5.50
0.50
0.62
6.00
4.75
168.3
165
178
16
18
178
140
6.625
6.50
7.00
0.62
0.69
7.00
5.50
219.1
197
213
22
24
229
191
8.625
7.76
8.38
0.88
0.94
9.00
7.50
273.0
229
248
22
24
229
191
10.750
9.02
9.75
0.88
0.94
9.00
7.50
323.9
254
286
25
25
279
241
12.750
10.00
11.25
1.00
1.00
11.00
9.50

www.shurjoint.com

Weight
Kgs / Lbs
4.75
10.47
6.91
15.23
11.93
26.30
46.1
101.4
20.00
44.00
32.00
70.40

Catalog 2011

MODELS

901 90 SR ELBOW
903 SR tee
Shurjoint short radius fittings, while primarily
designed for fire protection applications,
can also be used for general service
requirements.

C-E

C-E
Nominal Pipe

Size

mm / in

50

2

65

2


76.1mm


80

3

100

4

125

5

125

5


165.1mm


150

6

200

8

Pipe
O.D.
mm / in
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625

#901 SR 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
70
0.7
2.75
1.5
76
0.9
3.00
2.0
76
1.1
3.00
2.5
86
1.4
3.38
3.1
102
2.2
4.00
4.9
124
3.6
4.88
7.9
124
3.6
4.88
7.9
140
5.9
5.50
12.9
140
5.9
5.50
12.9
176
10.6
6.94
23.4

MODEL

The Model 7110DR is a grooved-end ductile

iron cast elbow with an integral 1" NPT or


use in fire protection and general service
applications.

#903 SR Straight Tee


C - E
Weight
mm / in
Kgs / Lbs
70
1.0
2.75
2.2
76
1.3
3.00
2.9
76
1.3
3.00
2.9
86
2.0
3.38
4.4
102
3.6
4.00
7.9
124
5.1
4.88
11.1
124
4.6
4.88
10.1
140
7.5
5.50
16.5
140
7.8
5.50
17.2
176
16.5
6.94
36.3

C-E

7110DR DRAIN ELBOW


BSP drain. The 7110DR is designed for

C-E

C-E

Nominal Pipe

Size

mm / in

50

2

65

2


76.1mm


80

3

100

4


165.1mm


150

6

200

8

Pipe
O.D.
C - E
mm / in
mm / in
60.3
83
2.375
3.27
73.0
95
2.875
3.75
76.1
95
3.000
3.75
88.9
108
3.500
4.25
114.3
127
4.500
5.00
165.1
165
6.500
6.50
168.3
165
6.625
6.50
219.1
197
8.625
7.76

1" NPT

Dimensions
D
mm / in
57.2
2.25
70
2.75
70
2.75
70
2.75
70
2.75
70
2.75
70
2.75
83
3.27

MODEL

7127 STANDPIPE TEE


E
mm / in
40
1.57
40
1.57
40
1.57
49
1.93
63
2.48
90
3.54
90
3.54
114
4.49

Weight
Kgs / Lbs
1.0
2.2
1.3
2.8
1.3
2.8
2.1
4.6
3.0
6.6
6.1
13.4
6.1
13.4
11.6
25.6

C-EB
NPT or BSP

The Model 7127 is a grooved-end tee


C-ER

with a 2" NPT/BSP threaded branch,


specially designed for use on fire protection
standpipes.

Connect with the Best!

Nominal
Size
mm / in
100 x 100 x 65
4 x 4 x 2
150 x 150 x 65
6 x 6 x 2

Pipe
O.D.
mm / in
114.3 x 114.3 x 73.0
4.500 x 4.500 x 2.875
168.3 x 168.3 x 73.0
6.625 x 6.625 x 2.875

C - ER
mm / in
83
3.25
83
3.25

Dimensions

C - EB
mm / in
102
4.00
127
5.00

www.shurjoint.com

Weight
Kgs / Lbs
2.65
5.84
4.30
9.48

49
Copyright 2011 Shurjoint

Catalog 2011

MODEL

7125 BULLHEAD TEE


C-EB

C-ER

The Model 7125 is a grooved-end bullhead


tee, specifically designed for use on fire
protection systems. The 7125 allows you
to directly split the flow into two reduced
branch lines without the need for concentric
reducers and multiple couplings.
Fire Protection Applications
7125 Bullhead Tee
Waterflow Indicator
RCV Riser Check Valve With
Trim Kit

SJ-700W Butterfly Valve


7707/7705 Flexible Couplings
Z07/7771 Rigid Couplings

Nominal Pipe

Size

mm / in
50 x 50 x 65
2 x 2 x 2
50 x 50 x 80

2 x 2 x 3
50 x 50 x 100

2 x 2 x 4
65 x 65 x 80
2 x 2 x 3
65 x 65 x 100
2 x 2 x 4
80 x 80 x 100

3 x 3 x 4
100x 100 x 150

4 x 4 x 6
125 x 125 x 200

5 x 5 x 8
150 x 150 x 200

6 x 6 x 8

Pipe
O.D.
mm / in
60.3 x 60.3 x 73.0
2.375 x 2.375 x 2.875
60.3 x 60.3 x 88.9
2.375 x 2.375 x 3.500
60.3 x 60.3 x 114.3
2.375 x 2.375 x 4.500
73.0x 73.0 x 88.9
2.875 x 2.875 x 3.500
73.0 x 73.0 x 114.3
2.875 x 2.875 x 4.500
88.9 x 88.9 x 114.3
3.500 x 3.500 x 4.500
114.3 x 114.3 x 168.3
4.500 x 4.500 x 6.625
141.3 x 141.3 x 219.1
5.563 x 5.563 x 8.625
168.3 x 168.3 x 219.1
6.625 x 6.625 x 8.625

C - ER
mm / in
95
3.74
108
4.25
127
5.00
108
4.25
127
5.00
127
5.00
165
6.50
197
7.75
197
7.75

Dimensions

C - EB
mm / in
83
3.27
95
3.74
102
4.02
95
3.75
102
4.00
102
4.00
127
5.00
140
5.50
165
6.50

Weight
Kgs / Lbs
1.83
4.03
1.97
4.34
3.20
7.05
2.55
5.62
3.32
7.32
3.60
7.94
6.80
14.99
14.00
31.00
13.21
29.12

MODEL

7150F REDUCING SOCKET (Gr x Ft)


7150M REDUCING NIPPLE (Gr x Mt)
The Shurjoint Models 7150F & 7150M
are designed for making a direct
reduction from a grooved system to
a female or male threaded system
without the need for more costly
swaged nipples or adapters.

7150F

7150M

50
Copyright 2011 Shurjoint


Nominal Size
7150F
7150M
Grooved x Threaded
L
Weight
L
Weight

mm / in
mm / in Kgs / Lbs mm / in Kgs / Lbs

40 x 25
63.5
0.27
63.5
0.24

1 x 1
2.5
0.60
2.5
0.53

50 x 25
63.5
0.42
63.5
0.40

2 x 1
2.5
0.92
2.5
0.88

50 x 32
63.5
0.46
63.5
0.32

2 x 1
2.5
1.01
2.5
0.70

50 x 40
63.5
0.43
63.5
0.47

2 x 1
2.5
0.95
2.5
1.04

65 x 25
63.5
0.55
63.5
0.40

2 x 1
2.5
1.21
2.5
0.88


63.5
0.55
63.5
0.75
76.1mm x 25

2.5
1.21
2.5
1.64

65 x 32
63.5
0.53
63.5
0.72

2 x 1
2.5
1.17
2.5
1.59


63.5
0.53
63.5
0.72
76.1mm x 32

2.5
1.17
2.5
1.59

65 x 40
63.5
0.49
63.5
0.78

2 x 1
2.5
1.08
2.5
1.72


63.5
0.49
63.5
0.78
76.1mm x 40

2.5
1.08
2.5
1.72

65 x 50
63.5
0.69
63.5
0.42

2 x 2
2.5
1.52
2.5
0.92


63.5
0.69
63.5
0.49
76.1mm x 50

2.5
1.52
2.5
1.09

80 x 25
63.5
0.87
63.5
0.57

3 x 1
2.5
1.91
2.5
1.25

80 x 32
63.5
0.68
63.5
0.76

3 x 1
2.5
1.50
2.5
1.67

80 x 40
63.5
0.74
63.5
0.74

3 x 1
2.5
1.63
2.5
1.63

80 x 50
63.5
0.71
63.5
0.60

3 x 2
2.5
1.56
2.5
1.32

80 x 65
63.5
1.00
63.5
1.00

3 x 2
2.5
2.20
2.5
2.20

Connect with the Best!


Nominal Size
7150F
7150M
Grooved x Threaded
L
Weight
L
Weight

mm / in
mm / in Kgs / Lbs mm / in Kgs / Lbs


63.5
1.00
63.5
1.00
80 x 76.1mm

2.5
2.20
2.5
2.20

100 x 32
76.1
1.06
76.1
0.99

4 x 1
3
2.33
3
2.19

100 x 40
76.1
0.93
76.1
0.93

4 x 1
3
2.05
3
2.05

100 x 50
76.1
1.03
76.1
1.05

4 x 2
3
2.29
3
2.31

100 x 65
76.1
1.02
76.1
0.93

4 x 2
3
2.25
3
2.05


76.1
1.02
76.1
0.93
100 x 76.1mm

3
2.25
3
2.05

125 x 40
88.9
1.79
88.9
0.93

5 x 1
3.5
3.94
3.5
2.05


88.9
1.79
88.9
0.93
139.7mm x 40

3.5
3.94
3.5
2.05

150 x 40
101.6
2.94
101.6
2.20

6 x 1
4
6.47
4
4.84


101.6
2.52
101.6
2.16
165.1mm x 40

4
5.56
4
4.75

150 x 50
101.6
2.40
101.6
2.23

6 x 2
4
5.28
4
4.91


101.6
2.40
101.6
2.23
165.1mm x 50

4
5.28
4
4.91

150 x 65
101.6
2.48
101.6
2.26

6 x 2
4
5.46
4
4.97


101.6
2.00
101.6
2.26
165.1mm x 65

4
4.40
4
4.97

150 x 100
101.6
2.89
101.6
2.10

6 x 4
4
6.37
4
4.62


101.6
2.10
101.6
2.10
165.1mm x 100

4
4.62
4
4.62

www.shurjoint.com

Catalog 2011

MODEL

899 END-ALL FITTING


The Model 899 End-All fitting is a unique
domed end cap fitting available with a
, or 1 NPT or BSP threaded outlet.
Designed as an end of line fitting, the EndAll features two multi-function bosses which
can be used for the
direct connection of
sprinkler heads, sprigs,
drops, drains and or
gauges.

B
A

NPT or BSP

MODEL

55 ADAPTER NIPPLE

(Gr x MT)

Nominal Size
Grooved x Threaded A
mm / in
mm / in
32 x 15
44.5
1 x
1.750
32 x 20
44.5
1 x
1.750
32 x 25
48.3
1 x 1
1.900
40 x 15
44.5
1 x
1.750
40 x 20
44.5
1 x
1.750
40 x 25
48.3
1 x 1
1.900
50 x 15
44.5
2 x
1.750
50 x 20
44.5
2 x
1.750
50 x 25
48.3
2 x 1
1.900
65 x 15
44.5
2 x
1.750
65 x 20
44.5
2 x
1.750
65 x 25
48.3
2 x 1
1.900

Dimensions

B
mm / in
30.1
1.190
30.1
1.190
31.8
1.250
33.3
1.313
33.3
1.313
34.9
1.375
39.7
1.562
39.7
1.562
41.3
1.625
44.5
1.750
44.5
1.750
46.0
1.813

Weight
Kgs / Lbs
0.3
0.7
0.3
0.7
0.3
0.7
0.4
0.9
0.4
0.9
0.4
0.9
0.5
1.1
0.5
1.1
0.5
1.1
0.6
1.3
0.6
1.3
0.6
1.3

MODEL

56 HOSE NIPPLE
The Shurjoint Model 56 hose nipple allows

The Shurjoint Model 55 is an integral cast


adapter that allows for a direct transition
from a grooved system to a male threaded
system or component. For other sizes see

for a direct connection with rubber or plastic


hoses.

E-E

Material: Ductile iron ASTM A536 Gr. 65-4512 and or ASTM A395 Gr. 65-45-15.

page 55, Models 57 through 59 nipples


adapters.

NPT or BSP


Nominal Size
Grooved x Threaded

mm / in

40 x 40M

1 x 1M

50 x 50M

2 x 2M

L
mm / in
63.5
2.50
63.5
2.50

Weight
Kgs / Lbs
0.35
0.77
0.40
0.90

Connect with the Best!

Nominal

Size
mm / in

32

1

40

1

50

2

65

2

80

3

100

4

125

5

150

6

200

8

Pipe
O.D.
mm / in
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625

www.shurjoint.com

E - E
mm / in
92
3.6
102
4.0
117
4.6
140
5.5
152
6.0
184
7.25
248
9.75
279
11.0
318
12.5

Weight
Kgs / Lbs
0.3
0.7
0.3
0.7
0.6
1.2
1.0
2.2
1.5
3.3
2.5
5.5
3.7
8.1
6.6
14.5
11.0
24.2

51
Copyright 2011 Shurjoint

Catalog 2011

Sprinkler Hubs
The Shurjoint Sprinkler Hubs are grooved-end manifold fittings
with a number of threaded outlets to accommodate flexible sprinkler
hoses. The Sprinkler Hubs can also be used in combination with
flexible sprinkler hoses and traditional hard piping depending on
your requirements. These fittings work as a hub for multiple flexible
hoses and or hard pipe runs, thus reducing the number or headers,
drop nipples and fittings required. All outlets are 1 NPT or BSPT.
Maximum working pressure is 300 psi (20 bar, 2.0 MPa) CWP.
cULus listed and FM approved. The C-to-E dimensions conform to
ANSI B16.3 Class 150.

MODEL

850 Sprinkler Hub 3 Outlets

MODEL

853 Sprinkler End Hub 4 Outlets


A

Size A
mm / in
mm / in
50 x 50 x 25 (3)
60
2 x 2 x 1 (3)
2.38
65 x 65 x 25 (3)
60
2 x 2 x 1 (3)
2.38

B
mm / in
51
2.02
57
2.25

N.W.
Kgs / Lbs
0.90
2.00
1.25
2.75

( ): Number of outlets

Size A
mm / in
mm / in
40 x 25 (4)
60
1 x 1 (4)
2.38
50 x 25 (4)
60
2 x 1 (4)
2.38
65 x 25 (4)
60
2 x 1 (4)
2.38

B
mm / in
46
1.80
51
2.02
57
2.25

( ): Number of outlets
MODEL

851 Reducing Sprinkler Hub

3 Outlets

Size A
mm / in
mm / in
50 x 40 x 25 (3)
60
2 x 1 x 1 (3)
2.38
65 x 40 x 25 (3)
60
2 x 1 x 1 (3)
2.38
65 x 50 x 25 (3)
60
2 x 2 x 1 (3)
2.38

B
mm / in
51
2.02
57
2.25
60
2.25

N.W.
Kgs / Lbs
1.14
2.52
1.20
2.65
1.23
2.71

( ): Number of outlets

52
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

N.W.
Kgs / Lbs
0.74
1.63
0.88
1.94
1.15
2.54

Catalog 2011

MODEL

7114 Hydrant ELBOW


2" BSP
Threaded

The Model 7114 Hydrant Elbow is designed


C-BE

for use on fire protection systems. The small

3" Grooved

end of the elbow offers both a 2" BSP


threaded outlet as well as a 3" grooved

Boss

connection. The boss can be factory tapped


to 1" BSP on request.

C-E






Nominal Pipe
Size
mm / in
100 x 80 x 25
4 x 3 x 1
150 x 80 x 25
6 x 3 x 1

Pipe
O.D.
mm / in
114.3 x 88.9 x 33.4
4.500 x 3.500 x 1.315
165.1 x 88.9 x 33.4
6.500 x 3.500 x 1.315

C - E
mm / in
102
4.00
130
5.13

Dimensions

C - BE
mm / in
95
3.75
130
5.13

Weight
Kgs / Lbs
2.70
5.95
4.0
8.8

MODEL

7122 Hydrant TEE

3" Grooved
C-BE

The Model 7122 Hydrant Tee is designed

2" BSP
Threaded

for use on fire protection systems. The 7122


tee offers both a 2" BSP threaded and a

Boss

3" grooved outlet. The boss can be factory


tapped to 1" BSP on request.

C-E

Nominal Pipe

Size

mm / in

100 x 100 x 80

4 x 4 x 3
165.1 x 165.1 x 80

6 x 6 x 3

Pipe
O.D.
mm / in
114.3 x 114.3 x 88.9
4.500 x 4.500 x 3.500
165.1 x 165.1 x 88.9
6.500 x 6.500 x 3.500

C - E
mm / in
102
4.00
130
5.13

Dimensions

C - BE
mm / in
102
4.00
130
5.13

Weight
Kgs / Lbs
3.50
7.72
5.54
12.21

MODEL

7133 PITCHER TEE

B
C

The Shurjoint pitcher tee provides a quick


and easy connection and transition from a

grooved riser system to a threaded hydrant


valve outlet. The pitcher tee is designed

2 BSP
threaded
3" Grooved

for 3", 4" and 6" steel pipe risers with a


2" BSP threaded or 3" grooved hydrant
connection outlet.


Nominal Pipe

Size

mm / in


80 x 80 x 76.1mm



100 x 100 x 76.1mm



165.1 x 165.1 x 76.1mm

Connect with the Best!

Pip
O.D.
mm / in
88.9 x 88.9 x 76.1
3.500 x 3.500 x 3.000
114.3 x 114.3 x 76.1
4.500 x 4.500 x 3.000
165.1 x 165.1 x 76.1
6.500 x 6.500 x 3.000

Hydrant

Outlet A
mm / in
mm / in
BSP
121
Taper
4.75
BSP
121
Taper
4.75
BSP
121
Taper
4.75

Dimensions Approx.
B
C
Weight
mm / in
mm / in
Kgs / Lbs
121
69
2.8
4.75
2.72
6.2
133
69
3.4
5.25
2.72
7.5
159
69
8.7
6.25
2.72
19.1

www.shurjoint.com

53
Copyright 2011 Shurjoint

WROUGHT GROOVED FITTINGS


MODEL

W110 90 ELBOW, S/R


W120 TEE

Catalog 2011

W110LR 90 ELBOW, L/R


W160 CAP

W111LR 45 ELBOW

Shurjoint wrought steel grooved fittings are


fabricated from standard weight (0.375 or

E-E

9.5mm) carbon steel pipe to ASTM A234 Gr.


WPB, or segmentally welded with carbon
steel of the same or equivalent grade. C-E
dimensions conform to ANSI B16.9.














Nominal
Size
mm / in
350
14
400
16
450
18
500
20
550
22
600
24

Pipe
O.D.
mm / in
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
558.8
22.000
609.6
24.000

W110

W110 90 S/R Elbows


C-E
Weight
mm / in
Kgs / Lbs
355.6
45.3
14.00
99.7
406.4
59.1
16.00
130.0
457.2
75.3
18.00
165.7
508.0
93.1
20.00
204.8
558.8
113.0
22.00
248.6
609.6
135.0
24.00
297.0

C-E

C-E

W110LR

W110LR 90 L/R Elbows


C-E
Weight
mm / in
Kgs / Lbs
533.4
67.9
21.00
149.4
609.6
89.0
24.00
195.8
685.8
113.0
27.00
248.6
762.0
140.0
30.00
308.0
838.2
169.0
33.00
371.8
914.4
202.0
36.00
444.4

C-E

C-E
W111LR

W111LR 45 L/R Elbows


C-E
Weight
mm / in
Kgs / Lbs
222.3
34.0
8.75
74.8
254.0
44.6
10.00
98.1
285.5
56.5
11.25
124.3
317.5
70.0
12.50
154.0
342.9
85.0
13.50
187.0
381.0
101.0
15.00
222.2

C-E
W120

W120 Tee
C-E
Weight
mm / in
Kgs / Lbs
279.4
53.5
11.00
117.7
304.8
66.1
12.00
145.4
342.9
83.9
13.50
184.6
381.0
104.0
15.00
228.8
419.1
126.0
16.50
277.2
431.8
139.0
17.00
305.8

W160
W160 Cap
E-E
Weight
mm / in
Kgs / Lbs
165.0
15.9
6.50
35.0
178.0
20.0
7.00
44.0
203.0
25.5
8.00
56.1
229.0
31.8
9.00
70.0
254.0
38.8
10.00
85.4
267.0
45.1
10.50
99.2

MODEL

W121 Reducing Tee


Material: ASTM A234 Gr. WPB, standard
weight (0.375 or 9.5mm), or carbon steel of

C-E

the same or equivalent grade.

C-B

C-E & C-B dimensions conform to ANSI

W121

B16.9
































Nominal
Size
mm / in
350 x 150
14 x 6
350 x 200
14 x 8
350 x 250
14 x 10
350 x 300
14 x 12
400 x 150
16 x 6
400 x 200
16 x 8
400 x 250
16 x 10
400 x 300
16 x 12
400 x 350
16 x 14
450 x 150
18 x 6
450 x 200
18 x 8
450 x 250
18 x 10
450 x 300
18 x 12
450 x 350
18 x 14
450 x 400
18 x 16

54
Copyright 2011 Shurjoint

Pipe
O. D.
mm / in
355.6 x 168.3
14.000 x 6.625
355.6 x 219.1
14.000 x 8.625
355.6 x 273.0
14.000 x 10.750
355.6 x 323.9
14.000 x 12.750
406.4 x 168.3
16.000 x 6.625
406.4 x 219.1
16.000 x 8.625
406.4 x 273.0
16.000 x 10.750
406.4 x 323.9
16.000 x 12.750
406.4 x 355.6
16.000 x 14.000
457.2 x 168.3
18.000 x 6.625
457.2 x 219.1
18.000 x 8.625
457.2 x 273.0
18.000 x 10.750
457.2 x 323.9
18.000 x 12.750
457.2 x 355.6
18.000 x 14.000
457.2 x 406.4
18.000 x 16.000

W121 Reducing Tee


C - E
C - B
mm / in
mm / in
279.0
238.0
11.0
9.37
279.0
248.0
11.0
9.76
279.0
257.0
11.0
10.12
279.0
270.0
11.0
10.63
30.50
264.0
12.0
10.40
305.0
273.0
12.0
10.75
305.0
282.0
12.0
11.10
305.0
295.0
12.0
11.61
305.0
305.0
12.0
12.00
343.0
289.0
13.5
11.38
343.0
298.0
13.5
11.38
343.0
308.0
13.5
12.13
343.0
321.0
13.5
12.64
343.0
330.0
13.5
13.00
343.0
330.0
13.5
13.00

Connect with the Best!

Weight
Kgs / Lbs
46.0
101.20
46.5
102.30
47.7
104.94
44.0
96.8
57.2
125.84
57.8
127.16
58.9
129.58
60.1
132.22
61.1
134.42
72.6
159.72
73.0
160.60
74.0
162.80
75.1
165.22
76.0
167.20
76.3
167.86

Nominal
Size
mm / in
500 x 150
20 x 6
500 x 200
20 x 8
500 x 250
20 x 10
500 x 300
20 x 12
500 x 350
20 x 14
500 x 400
20 x 16
500 x 450
20 x 18
600 x 150
24 x 6
600 x 200
24 x 8
600 x 250
24 x 10
600 x 300
24 x 12
600 x 350
24 x 14
600 x 400
24 x 16
600 x 450
24 x 18
600 x 500
24 x 20

Pipe
O. D.
mm / in
508.0 x 168.3
20.000 x 6.625
508.0 x 219.1
20.000 x 8.625
508.0 x 273.0
18.000 x 10.750
508.0 x 323.9
20.000 x 12.750
508.0 x 355.6
20.000 x 14.000
508.0 x 406.4
20.000 x 16.000
508.0 x 457.2
20.000 x18.000
609.6 x 168.3
20.000 x 6.625
609.6 x 219.1
20.000 x 8.625
609.6 x 273.0
24.000 x 10.750
609.6 x 323.9
24.000 x 12.750
609.6 x 355.6
24.000x14.000
609.6 x 406.4
24.000 x 16.000
609.6 x 457.2
24.000x18.000
609.6 x 508.0
24.000 x 20.000

W121 Reducing Tee


C - E
C - B
mm / in
mm / in
381.0
314.0
15.0
12.36
381.0
324.0
15.0
12.76
381.0
333.0
18.0
13.11
381.0
346.0
15.0
13.62
381.0
356.0
15.0
14.02
381.0
356.0
15.0
14.02
381.0
368.0
15.0
14.50
432.0
365.0
17.0
14.38
432.0
375.0
17.0
14.76
432.0
384.0
17.0
15.12
432.0
397.0
17.0
15.63
432.0
406.0
17.0
16.00
432.0
406.0
17.0
16.00
432.0
419.0
17.0
16.50
432.0
432.0
17.0
17.00

www.shurjoint.com

Weight
Kgs / Lbs
89.5
196.90
90.0
198.0
90.9
199.98
92.0
202.40
92.9
204.38
93.6
204.60
94.5
207.90
122.0
268.40
123.0
270.6
123.2
271.04
124.2
273.24
125.0
275.0
125.0
275.0
127.1
279.62
128.0
281.60

WROUGHT GROOVED FITTINGS

Catalog 2011

MODEL

W150 WROUGHT CONCENTRIC REDUCER


W151 WROUGHT ECCENTRIC REDUCER
Material: ASTM A234 Gr. WPB, standard

weight (0.375 or 9.5mm), or segmentally


welded carbon steel of the same or
equivalent grade
E-E dimensions conform to ANSI B16.9.

E-E

E-E

W150

W151

MODEL

57 NIPPLE, Groove X Groove


58 NIPPLE, Groove X Bevel
59 NIPPLE, Groove X Thread
Model 57
E-E

Gr. x Gr.
Model 58
E-E

Gr. x Bev.
Model 59
E-E

Gr. x Th

Nominal Pipe
Size
mm / in
350 x 150
14 x 6
350 x 200
14 x 8
350 x 250
14 x 10
350 x 300
14 x 12
400 x 200
16 x 8
400 x 250
16 x 10
400 x 300
16 x 12
400 x 350
16 x 14
450 x 250
18 x 10
450 x 300
18 x 12
450 x 350
18 x 14
450 x 400
18 x 16
500 x 300
20 x 12
500 x 350
20 x 14
500 x 400
20 x 16
500 x 450
20 x 18
600 x 400
24 x 16
600 x 450
24 x 18
600 x 500
24 x 20

Nominal
Pipe Size
mm / in

20



25

1

32

1

40

1

50

2

65

2

80

3

100

4

125

5

150

6

200

8

250

10

300

12

Connect with the Best!

Pipe
O.D.
mm / in
355.6 x 168.3
14.000 x 6.625
355.6 x 219.1
14.000 x 8.625
355.6 x 273.0
14.000 x 10.750
355.6 x 323.9
14.000 x 12.750
406.4 x 219.1
16.000 x 8.625
406.4 x 273.0
16.000 x 10.750
406.4 x 323.9
16.000 x 12.750
406.4 x 355.6
16.000 x 14.000
457.2 x 273.0
18.000 x 10.750
457.2 x 323.9
18.000 x 12.750
457.2 x 355.6
18.000 x 14.000
457.2 x 406.4
18.000 x 16.000
508.0 x 323.9
20.000 x 12.750
508.0 x 355.6
20.000 x 14.000
508.0 x 406.4
20.000 x 16.000
508.0 x 457.2
20.000 x18.000
609.6 x 406.4
24.000 x 16.000
609.6 x 457.2
24.000x18.000
609.6 x 508.0
24.000 x 20.000

Pipe
O.D.
mm / in
26.7
1.050
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750

W150 Concentric Reducer


E-E
Weight
mm / in
Kgs / Lbs
330.0
30.8
13.00
67.76
330.0
31.8
13.00
69.96
330.0
32.7
13.00
71.94
330.0
33.6
13.00
73.92
356.0
39.9
14.00
87.78
356.0
41.3
14.00
90.86
356.0
42.2
14.00
92.84
356.0
43.1
14.00
94.82
381.0
50.8
15.00
111.76
381.0
52.2
15.00
114.84
381.0
53.5
15.00
117.70
381.0
54.9
15.00
120.78
508.0
72.6
20.00
159.72
508.0
74.4
20.00
163.68
508.0
76.2
20.00
167.64
508.0
78.0
20.00
171.6
508.0
89.8
20.00
197.56
508.0
90.7
20.00
199.54
508.0
92.5
20.00
203.50

57 (Gr x Gr)
E - E
Weight
mm / in
Kgs / Lbs
76
0.13
3
0.29
76
0.19
3
0.42
102
0.31
4
0.68
102
0.37
4
0.82
102
0.50
4
1.10
102
0.80
4
1.76
102
1.10
4
2.40
152
2.35
6
5.17
152
3.30
6
7.26
152
4.50
6
9.90
152
6.50
6
14.30
203
12.30
8
27.06
203
16.20
8
35.64

W151 Eccentric Reducer


E-E
Weight
mm / in
Kgs / Lbs
330.0
30.8
13.00
67.76
330.0
31.8
13.00
69.96
330.0
32.7
13.00
71.94
330.0
33.6
13.00
73.92
356.0
39.9
14.00
87.78
356.0
41.3
14.00
90.86
356.0
42.2
14.00
92.84
356.0
43.1
14.00
94.82
381.0
50.8
15.00
111.76
381.0
52.2
15.00
114.84
381.0
53.5
15.00
117.70
381.0
54.9
15.00
120.78
508.0
72.6
20.00
159.72
508.0
74.4
20.00
163.68
508.0
76.2
20.00
167.64
508.0
78.0
20.00
171.6
508.0
89.8
20.00
197.56
508.0
90.7
20.00
199.54
508.0
92.5
20.00
203.50

58 (Gr x Bev)
E - E
Weight
mm / in
Kgs / Lbs
76
0.13
3
0.29
76
0.19
3
0.42
102
0.32
4
0.70
102
0.38
4
0.84
102
0.50
4
1.10
102
0.80
4
1.76
102
1.10
4
2.40
152
2.35
6
5.17
152
3.30
6
7.26
152
4.50
6
9.90
152
6.50
6
14.30
203
8.66
8
19.00
203
10.16
8
22.35

www.shurjoint.com

59 (Gr x Th)
E - E
Weight
mm / in
Kgs / Lbs
76
0.13
3
0.29
76
0.19
3
0.42
102
0.30
4
0.66
102
0.36
4
0.79
102
0.50
4
1.10
102
0.72
4
1.54
102
1.00
4
2.20
152
2.20
6
4.84
152
3.00
6
6.60
152
4.46
6
9.81
---
-----
-----
-----
-----
-----
---

55
Copyright 2011 Shurjoint

wrought 3d elbows
MODELs

L90-3D 90
L30-3D 30

L60-3D 60
L22-3D 22

L45-3D 45
L11-3D 11

1. Long radius 90 elbows 3D, 5D, and 6D in

C606-04 and or ISO/FDIS 6182-12. For

sizes up to and including 4 are provided

dimensional tolerances of cast fittings,

with 4 (102 mm) long tangents, sizes 5


to 10 are provided with 1D long tangents

on request).
4. C to E tolerances: 2 through 6 1/8

refer to ISO/FDIS 6182-12 Table 3..

(3.2mm); 8 through 16 1/4 (6.4mm);

Plain-end or beveled end is also

and sizes 12 to 24 are provided with 12


(305mm) long tangents.

Catalog 2011

18 through 24 3/8 (9.5mm).

available upon request.

5. All weights are approximate, based on

3. Material: Standard wall steel pipe to ASTM

2. End Preparation: Roll-grooved to AWWA

calculated weight of pipe.

A53, Grade B. (Other materials available


E
C-

L60-3D

L90-3D
Nominal

Size
mm / in

50

2

65

2

80

3


101.6mm


100

4

125

5

150

6

200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

Pipe
OD
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
101.6
4.000
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.1
10.750
323.9
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000

L90-3D 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
254
2.5
10.0
5.51
292
4.5
11.5
9.92
330
6.63
13.0
14.62
368
8.4
14.5
18.6
406
10.18
16.0
22.44
508
18.39
20.0
40.54
610
27.52
24.0
60.67
813
60
32.0
132.28
1016
96
40.0
211.64
1219
145
48.0
319.67
1372
177
54.0
390.22
1524
248
60.0
546.75
1676
290.6
66.0
639.2
1829
282
72.0
621.7
2134
607
84.0
1338.2

C-E

C-E

R=3D

C-E

C-E

E
C-

L60-3D 60 Elbow
C - E
Weight
mm / in
Kgs / Lbs
191
2.0
7.50
4.3
210
3.5
8.25
7.7
235
5.0
9.25
11.0
254
6.5
10.00
14.4
279
8.4
11.00
18.5
349
14.2
13.75
31.3
419
22.1
16.50
48.8
559
44.4
22.00
97.9
692
78.7
27.25
173.4
832
115.6
32.75
254.8
972
148.5
38.25
327.3
1111
194.6
43.75
429.0
1251
246.9
49.25
544.4
1391
305.5
54.75
673.5
1664
441.3
65.50
973.0

L45-3D
L45-3D 45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
165
1.7
6.50
3.75
184
3.0
7.25
6.7
197
4.6
7.75
10.14
216
5.6
8.50
12.0
229
6.69
9.00
14.75
286
12.18
11.25
26.85
343
18
13.50
39.68
457
39
18.00
85.98
572
62
22.50
136.69
686
93
27.00
205.03
800
103.1
31.50
227.3
914
159
36.00
350.54
1029
209.2
40.25
461.3
1143
258
45.00
568.79
1365
396
53.75
873.03

L30-3D
L30-3D 30 Elbow
C - E
Weight
mm / in
Kgs / Lbs
146
1.5
5.75
3.4
152
2.6
6.00
5.8
165
3.6
6.50
8.0
171
4.6
6.75
10.2
184
5.8
7.25
12.8
229
9.9
9.00
21.8
273
15.4
10.75
3.9
368
30.8
14.50
68.0
457
54.7
18.00
120.5
552
80.3
21.75
177.0
641
103.1
25.25
227.3
737
135.1
29.00
297.9
826
171.5
32.50
378.1
914
212.2
36.00
467.8
1099
306.5
43.25
675.7

L22-3D
L22-3D 22 Elbow
C - E
Weight
mm / in
Kgs / Lbs
133
1.5
5.25
3.2
140
2.4
5.50
5.3
146
3.3
5.75
7.3
152
4.2
6.00
9.2
165
5.2
6.50
11.4
203
8.8
8.00
19.4
241
13.7
9.50
30.1
324
27.4
12.75
60.5
406
48.6
16.00
107.2
489
71.4
19.25
157.5
572
91.8
22.50
202.3
648
120.3
25.25
265.2
730
152.6
28.75
336.5
813
188.8
32.00
416.3
972
272.8
38.25
601.4

12 3D 90 elbows ready for shipment

56
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

L11-3D
L11-3D 11 Elbow
C - E
Weight
mm / in
Kgs / Lbs
114
1.3
4.50
2.8
121
2.1
4.75
4.6
127
2.8
5.00
6.2
127
3.4
5.00
7.6
133
4.2
5.25
9.3
165
7.2
6.50
15.8
197
11.2
7.75
24.6
267
22.4
10.50
49.3
330
39.6
13.00
87.3
394
58.2
15.50
128.3
464
74.8
18.25
164.8
527
98.0
20.75
216.0
593
124.3
23.35
274.1
660
153.9
26.00
339.2
787
222.3
31.00
490.0

wrought 5d elbows
MODELs

L90-5D 90
L30-5D 30
Nominal

Size
mm / in

50

2

65

2

80

3


101.6mm


100

4

125

5

150

6

200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

Pipe
OD
mm / in
60.3
2.375
73
2.875
88.9
3.500
101.6
4.000
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.1
10.750
323.9
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000

L60-5D 60
L22-5D 22

L90-5D 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
356
3.3
14.0
7.2
419
6.1
16.5
13.3
483
9.0
19.0
19.9
546
12.2
21.5
26.9
610
16.1
24.0
35.4
762
27.2
30.0
59.9
914
42.4
36.0
93.3
1219
85.2
48.0
187.4
1524
150.9
60.0
332.0
1829
221.8
72.0
488.0
2083
276.6
82.0
608.5
2337
354.4
92.0
779.7
2591
441.5
102.0
971.4
2845
538.6
112.0
1184.9
3353
761.3
132.0
1674.9

L60-5D 60 Elbow
C - E
Weight
mm / in
Kgs / Lbs
248
2.5
9.75
5.6
286
4.6
11.25
10.2
324
6.8
12.75
15
311
9.1
12.25
20
394
11.8
15.5
26
495
20
19.5
44.1
591
31.1
23.25
68.6
787
62.5
31
137.7
991
110.7
39
244.1
1187
162.7
46.75
358.6
1384
209
54.5
460.7
1581
273.9
62.25
603.8
1778
347.5
70
766.2
1975
430
77.75
947.9
2369
621.1
93.25
1369.3

wrought 6d elbows
MODELs

L90-6D 90
L30-6D 30
Nominal

Size
mm / in

50

2

65

2

80

3


101.6mm


100

4

125

5

150

6

200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

Pipe
OD
mm / in
60.3
2.375
73
2.875
88.9
3.500
101.6
4.000
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.1
10.750
323.9
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000

L60-6D 60
L22-6D 22

L90-6D 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
406
3.7
16.0
8.2
483
6.9
19.0
15.2
559
10.4
22.0
22.9
635
14.1
25.0
31.1
711
18.6
28.0
41.0
889
31.6
35.0
69.5
1067
49.2
42.0
108.2
1422
98.7
56.0
217.2
1778
174.9
70.0
384.9
2134
257.2
84.0
565.8
2438
322.0
96.0
708.4
2743
413.9
108.0
910.6
3048
517.0
120.0
1137.4
3353
632.0
132.0
1390.4
3962
896.4
156.0
1972.1

L60-6D 60 Elbow
C - E
Weight
mm / in
Kgs / Lbs
279
2.9
11
6.3
324
5.2
12.75
11.4
368
7.7
14.5
17
413
10.3
16.25
22.8
457
13.5
18
29.8
565
22.9
22.25
50.5
679
35.7
26.75
78.6
908
71.5
35.75
157.7
1137
126.7
44.75
279.4
1359
186.2
53.5
410.5
1588
239.2
62.5
527.3
1816
313.5
71.5
691.1
2045
397.8
80.5
877.1
2267
492.2
89.25
1085.1
2724
711
107.25
1567.5

Connect with the Best!

Catalog 2011

L45-5D 45
L11-5D 11
L45-5D 45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
210
2.2
8.25
4.8
235
3.9
9.25
8.6
260
5.7
10.25
12.5
286
7.5
11.25
16.5
318
9.7
12.5
21.3
394
16.4
15.5
36.1
470
25.5
18.5
56.2
622
51.2
24.5
112.8
781
90.7
30.75
199.9
940
133.2
37
293.7
1092
171.1
43
377.3
1251
224.3
49.25
494.5
1403
284.7
55.25
627.6
1562
352.2
61.5
776.4
1873
508.7
73.75
1121.6

L30-5D 30 Elbow
C - E
Weight
mm / in
Kgs / Lbs
171
1.8
6.75
4
191
3.2
7.5
7
203
4.5
8
10
222
5.9
8.75
13
241
7.5
9.5
16.6
298
12.7
11.75
28.1
356
19.9
14
43.8
476
39.9
18.75
87.9
597
70.7
23.5
155.8
711
103.8
28
228.9
832
133.4
32.75
294
953
174.8
37.5
385.3
1073
221.8
42.25
489
1187
274.4
46.75
605
1429
396.4
56.25
873.9

L22-5D 22 Elbow
C - E
Weight
mm / in
Kgs / Lbs
152
1.6
6
3.6
165
2.8
6.5
6.2
178
4
7
8.8
191
5.1
7.5
11.3
203
6.5
8
14.3
254
10.9
10
24.1
305
17.1
12
37.6
406
34.2
16
75.4
508
60.6
20
133.7
610
89.1
24
196.4
711
114.4
28
252.3
813
150
32
330.7
914
190.4
36
419.7
1016
235.5
40
519.2
1219
340.2
48
750.1

L11-5D 11 Elbow
C - E
Weight
mm / in
Kgs / Lbs
127
1.4
5
3
133
2.3
5.25
5
140
3.1
5.5
6.9
146
3.9
5.75
8.7
152
4.9
6
10.7
191
8.3
7.5
18.2
229
12.8
9
28.3
305
25.8
12
56.8
381
45.6
15
100.6
457
67
18
147.8
533
86.1
21
189.8
610
112.9
24
248.8
686
143.2
27
315.7
762
177.2
30
390.6
908
256
35.75
564.3

L22-6D 22 Elbow
C - E
Weight
mm / in
Kgs / Lbs
165
1.8
6.5
3.9
178
3
7
6.7
191
4.3
7.5
9.5
210
5.6
8.25
12.3
222
7.1
8.75
15.7
279
12
11
26.5
337
18.7
13.25
41.3
445
37.6
17.5
82.9
559
66.6
22
146.9
667
97.9
26.25
215.9
781
125.8
30.75
277.3
895
164.9
35.25
363.5
1003
209.2
39.5
461.3
1118
258.9
44
570.7
1329
373.9
52.34
824.4

L11-6D 11 Elbow
C - E
Weight
mm / in
Kgs / Lbs
133
1.5
5.25
3.2
140
2.4
5.5
5.3
146
3.3
5.75
7.3
152
4.2
6
9.2
165
5.2
6.5
11.4
203
8.8
8
19.4
241
13.7
9.5
30.1
324
27.4
12.75
60.5
406
48.6
16
107.2
483
71.4
19
157.5
565
91.8
22.25
202.3
648
120.3
25.5
265.2
730
152.6
28.75
336.5
806
188.8
31.75
416.3
972
272.8
38.25
601.4

L45-6D 45
L11-6D 11
L45-6D 45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
229
2.4
9
5.3
260
4.3
10.25
9.5
38
6.4
1.5
14
324
8.4
12.75
18.6
356
10.9
14
24.1
445
18.6
17.5
40.9
533
28.9
21
63.7
711
58
28
127.8
889
102.7
35
226.4
1060
150.9
41.75
332.7
1238
193.8
48.75
427.3
1416
254.1
55.75
560.1
1594
322.4
62.75
710.7
1772
398.8
69.75
879.3
2127
576.2
83.75
1270.3

L30-6D 30 Elbow
C - E
Weight
mm / in
Kgs / Lbs
184
2
7.25
4.3
203
3.5
8
7.7
222
5
8.75
11
248
6.5
9.75
14.4
267
8.4
10.5
18.5
330
14.2
13
31.3
400
22.1
15.75
48.8
533
44.4
21
97.9
660
78.7
26
173.4
794
115.6
31.25
254.8
927
148.5
36.5
327.3
1060
194.6
41.75
429
1194
246.9
47
544.4
1327
305.5
52.25
673.5
1588
441.3
62.5
973

www.shurjoint.com

57
Copyright 2011 Shurjoint

EXTRA HEAVY CUT GROOVEd


FITTINGS "EP" (End Protection)
MODEL

10EP 90 EP ELBOW
11EP 45 EP ELBOW

Catalog 2011

20EP EP Tee
35EP EP cross

Shurjoint offers a variety of fittings with

be used with XH-70EP couplings in high

extra heavy (Sch. 80) wall thickness and

pressure systems where the system

"EP" cut grooves available for use with

pressure exceeds the published ratings for

XH-70EP couplings. These fittings must

XH-1000 or Model 7707 couplings.

C-E

C-E

C-E

C-E

#10EP












Nominal
Size
mm / in
50
2
65
2
80
3
100
4
150
6

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
168.3
6.625

#10EP 90 Elbows
C - E
Weight
mm / in
Kgs / Lbs
83
1.0
3.25
2.2
95
1.7
3.75
3.8
108
2.7
4.25
5.9
127
4.4
5.00
9.7
165
10.4
6.50
22.9

#11EP 45 Elbows
C - E
Weight
mm / in
Kgs / Lbs
51
0.8
2.00
1.8
57
1.3
2.25
2.9
64
1.9
2.50
4.3
76
3.9
3.00
8.5
89
7.5
3.50
16.5

C-E

C-E

C-E
C-E
#20EP #11EP #35EP

C - E
mm / in
83
3.25
95
3.75
108
4.25
127
5.00
165
6.50

#20EP Tee
Weight
Kgs / Lbs
1.6
3.5
3.6
7.9
7.3
16.0
10.7
23.5
12.2
27.0

#35EP Cross
C - E
Weight
mm / in
Kgs / Lbs
83
1.8
3.25
3.9
95
3.0
3.75
6.6
108
6.4
4.25
14.2
127
7.2
5.00
15.8
165
20.9
6.50
46.0

For "EP cut-grooves, see page 26.

MODEL

22EP HEADER TEE


Shurjoint Model 22EP Header Tees are

C-E

specifically designed for use in oilfield


production headers where the top (test) line
is 2" (50mm) and the bottom production line

C-E

is 3" (80mm) or 4" (100mm).


#22EP

Pressure-Temperature Rating


Nom. Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

750 psi @100F


52 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C



Class 300

*Working pressure is based on roll- or cut-grooved standard wall


carbon steel pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

58
Copyright 2011 Shurjoint

Connect with the Best!

Fitting Size Mated C to E


Nominal Size
Pipe O. D.
mm / in
mm / in
50 to 80
60.3
2 to 3
2.375
50 to 100
73.0
2 to 4
2.875

C - E
mm / in
108
4.25
127
5.00

#22EP Header Tee

www.shurjoint.com

Weight
Kgs / Lbs
1.5
3.4
1.9
4.1

Section 3
Stainless Steel Series
Shurjoint Stainless Steel Piping Series.................................... 60
Grooved Mechanical Couplings
SS-5 Rigid Coupling........................................................................... 61
SS-7 Rigid Coupling........................................................................... 62
SS-7X Rigid Coupling........................................................................ 63
SS-8 Flexible Coupling....................................................................... 64
SS-8X Heavy Duty Flexible Coupling................................................. 65
SS-1200 High Pressure Flexible Coupling........................................ 66

SS-28 Hinged Lever Coupling............................................................ 67


Cast Grooved Fittings
SS-10 / SS-11 / SS-20 / SS-60 Elbows, Tee, Cap........................ 68
SS-21 / SS50 Reducing Tee, Concentric Reducer......................... 69
Wrought Grooved Fittings
WS-10 / WS-10L / WS-11 / WS-20 / WS -60 / WS-21 / WS-50
Elbows, Tee, Cap, Reducing Tee & Concentric Reducer....................70

Flange Adapters
SS-41 / SS-80 Flange Adapters....................................................... 71
Mechanical Tee, Y-Strainer & Valves
SS-723 / SS-726 Mechanical Tee, Y Strainer.................................. 72
SJ-600L / SJ-600W Ball Valves..................................................... 73
SJ-400-L / SJ-400-W Butterfly Valve............................................. 74

Connect with the Best!

Catalog 2011

www.shurjoint.com

Catalog 2011

Stainless Steel Series


Shurjoint offers a full range of stainless steel grooved
mechanical couplings in CF8 (304) and CF8M (316) for
general service applications and in specialty alloys for
applications including reverse osmosis and desalination
systems. Grooved fittings are available in sizes from 1
(25 mm) to 24 (600 mm) produced in a combination of
investment castings and wrought stainless.
The design pressure rating of Shurjoint stainless steel grooved
couplings follows Class 150 and is based on roll grooved Sch. 40S
pipe. Pressure ratings will vary depending on the type of pipe used
and grooves processed. For example; for cut grooved Sch. 40S pipe
- apply 110%, for roll grooved Sch.10S pipe - apply 80% and for rollgrooved Sch. 5S pipe - apply 50%. Shurjoint Model SS-1200 and

Model SS-8X are designed for high pressure applications for use with
cut-grooved Sch. 40S and or Sch. 80S pipe with pressures expressed
in CWP.
Shurjoint ductile iron couplings can be used in conjunction with
stainless steel pipe, depending on the application, as the flow media
does not come in direct contact with coupling housings but rather only
the gasket. See page 39 for performance data.

Groove corners are not defined

Stainless steel pipe in general is more difficult to groove than carbon


steel pipe, as it is more difficult to achieve defined groove corners on
stainless pipe. Grooves that are not defined and have too much of
a radius could result in joint failure. Care must be taken to process

OK

grooves as defined as possible. For this reason, roll-groove machine


manufacturers offer a variety of roll sets depending on the pipe
material and wall thickness being grooved. Always select the correct
roll set for the pipe being grooved.

If the same roll-set that has been used for carbon steel
pipe is used on stainless steel pipe, rust or scale may be
transferred to the stainless steel pipe during processing of the groove.
Thus we recommend the use of a separate roll set specifically for
use with stainless steel pipe. Also use caution to keep roll grooved
stainless steel pipe dry prior to installation.

Stainless Steel Casting Specifications


Austenitic Stainless Steel

Duplex (Austenitic / Ferritic) Stainless Steel

Grade

CF8

CF8M

CK3MCuN

2A, CE8MN

4A, CD3MN

5A, CE3MN

(UNS)

J92600

J92900

J93254

J93345

J92205

J93404

Composition, % (max, except where range is given)


Carbon

0.08

0.08

0.025

0.08

0.03

Manganese

1.50

1.50

1.20

1.00

1.50

0.03
1.50

Silicon

2.00

1.50

1.00

1.50

1.00

1.00
0.040

Sulfur

0.040

0.040

0.010

0.040

0.020

Phosphorus

0.040

0.040

0.045

0.040

0.040

0.040

Chromium

18.0-21.0

18.0-21.0

19.5-20.5

22.5-25.5

21.0-23.5

24.0-26.0

Nickel

8.0-11.0

9.0-12.0

17.5-19.5

8.0-11.0

4.5-6.5

6.0-8.0

Molybdenum

0.50

2.0-3.0

6.0-7.0

3.0-4.5

2.5-3.5

4.0-5.0

0.10-0.30

0.10-0.30

0.10-0.30

Nitrogen

0.18-0.24

Copper

0.50-1.00

1.00

Tensile Requirements, min.


Tensile Strength, ksi (MPa)

70 (485)

70 (485)

80 (550)

95 (655)

90 (620)

100 (690)

Yield Strength, ksi (MPa)

30 (205)

30 (205)

38 (260)

65 (450)

60 (415)

75 (515)

Elongation, %

35

30

35

25

25

18

ASTM Standards

A351/ A743/A744

A351/A743/A744

A351/A743/A744

A890/A351

A890

A890

Wrought Equivalent Grade

304

316

254SMO*

45D*

2205

SAF 2507*

* 254SMO is a registered trademark of AvestaPolarit AB, 45D is a registered trademark of ESCO Corporation and SAF 2507 is a registered trademark of AB Sandvik Steel.

60
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

SS-5

RIGID COUPLING

- Angle-Pad Design The Shurjoint Model SS-5 is an angle-pad

bolt you can make a fast and easy "swing-

design stainless steel coupling for use with

over installation. The SS-5 couplings are

Sch. 5S, Sch. 10S or Sch. 40S stainless

comprised of two identical CF8 (304) or

steel pipe where a rigid connection is

CF8M (316) housing segments, EPDM

desired. The angle-pad design allows the

gaskets and stainless steel track bolts and

coupling housings to slide along the bolt

heavy duty nuts.

The Shurjoint Model SS-5 is available with

pads when tightened. The result is an offset


clamping action which provides a rigid joint

a standard C shaped or GapSeal gasket

which resists so called snaking of a long

in a variety of grades to meet your specific

straight run. With the removal of only one

service requirements.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(STD, Roll-Grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

32

1

40

1

50

2

65

2


76.1mm


80

3

100

4


139.7mm


125

5


165.1mm


150

6

200

8


200 JIS

Pipe
O. D.
mm / in
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625
216.3
8.516

Max. Working
Pressure
Bar/PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Max. End
Load
kN / Lbs
2.80
650
3.66
850
5.71
1330
8.37
1950
9.09
2120
12.41
2080
20.51
4770
30.64
7120
31.35
7290
42.80
9950
44.47
10340
75.37
17520
73.45
17080

Connect with the Best!

Axial
Displacement
A
mm / in
mm / in
0 ~ 1.2
66
0 ~ 0.05
2.60
0 ~ 1.2
72
0 ~ 0.05
2.83
0 ~ 1.7
85
0 ~ 0.07
3.35
0 ~ 1.7
98
0 ~ 0.07
3.86
0 ~ 1.7
100
0 ~ 0.07
3.94
0 ~ 1.7
113
0 ~ 0.07
4.45
0 ~ 4.1
146
0 ~ 0.16
5.75
0 ~ 4.1
173
0 ~ 0.16
6.81
0 ~ 4.1
175
0 ~ 0.16
6.89
0 ~ 4.1
200
0 ~ 0.16
7.87
0 ~ 4.1
203
0 ~ 0.16
8.00
0 ~ 4.8
264
0 ~ 0.19
10.40
0 ~ 4.8
260
0 ~ 0.19
10.24

Dimensions
B
mm / in
102
4.00
109
4.29
117
4.61
132
5.20
136
5.35
148
5.83
182
7.17
227
8.94
229
9.02
246
9.69
249
9.80
330
12.99
340
13.39

Bolts Size
C
mm / in
No.
mm / in
46

M10 x 55
2
1.81
x 2
46

M10 x 55
2
1.81
x 2
47

M10 x 70
2
1.85
x 2
47

M10 x 70
2
1.85
x 2
47

M10 x 70
2
1.85
x 2
48

M10 x 70
2
1.88
x 2
53

M10 x 70
2
2.09
x 2
53

M12 x 75
2
2.09
x 3
53

M12 x 75
2
2.09
x 3
54

M12 x 75
2
2.13
x 3
54

M12 x 75
2
2.13
x 3
64

M16 x 135
2
2.52
x 5 5/16
64

M20 x 120
2
2.50
x 4

www.shurjoint.com

Weight
Kgs / Lbs
0.6
1.4
0.7
1.5
0.8
1.7
0.9
2.1
1.0
2.2
1.2
2.6
1.9
4.1
2.6
5.7
2.6
5.7
3.1
6.8
3.1
6.8
6.1
13.4
7.4
16.2

61
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SS-7 STAINLESS STEEL

Rigid Coupling

The Model SS-7 is a tongue and groove rigid

(316) with 304 and 316 bolts and nuts.

coupling designed for a variety of moderate

SS-7 couplings should always be installed

service pressure applications. The SS-7 is

so that the coupling bolt pads make metal to

supplied standard in CF8 (304) and CF8M

metal contact.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

32

1

40

1

50

2

65

2


76.1 mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6

200

8


200 JIS

Pipe
O. D.
mm / in
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625
216.3
8.516

Pipe End
Separation
A
mm / in
mm / in
0-1.6
68
0-0.06
2.68
0-1.6
74
0-0.06
2.91
0-1.6
86
0-0.06
3.39
0-1.6
100
0-0.06
3.94
0-1.6
100
0-0.06
3.94
0-1.6
112
0-0.06
4.41
0-3.2
143
0-0.13
5.63
0-3.2
172
0-0.13
6.77
0-3.2
171
0-0.13
6.73
0-3.2
195
0-0.13
7.68
0-3.2
201
0-0.13
7.91
0-3.2
264
0-0.13
10.39
0-3.2
257
0-0.13
10.12

Dimensions
Bolt
B
C
Size
Weight
mm / in
mm / in
in
Kgs / Lbs
105
45

0.7
x2
4.13
1.75
1.5
108
46

0.8
x2
4.25
1.81
1.8
125
46

0.9
x2
4.92
1.81
2.0
138
46

0.8
x2
5.43
1.81
1.8
143
46

1.0
x2
5.63
1.81
2.2
160
46

1.2
x2
6.30
1.81
2.6
207
51

2.1
x3
8.15
2.00
4.6
231
51

2.8
x3
9.09
2.00
6.2
236
51

2.7
x3
9.29
2.00
5.9
255
53

3.1
x3
10.04
2.09
6.8
256
51

3.1
x3
10.08
2.00
6.8
333
62

6.4
x 3
13.11
2.44
14.1
346
62

6.0
x 3
13.62
2.44
13.2

The tongue and groove style


rigid coupling may allow for
rotation when installed on undersized grooves.

Domestic Water Service

62
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

SS-7X STAINLESS STEEL

Rigid Coupling

The Model SS-7X is a tongue and groove

in CF8 (304) and CF8M (316) with 304

rigid coupling designed to provide a rigid

and 316 bolts and nuts. The bolts must be

joint for stainless steel pipe in sizes 10

fastened to the required torque for proper

through 24. The SS-7X is supplied standard

installation.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 2 times the working pressure.

10" ~ 14"


Nominal

Size

mm / in

250

10

300

12


250 JIS



300 JIS


350

14

400

16

450

18

500

20

550

22

600

24

Pipe
O. D.
mm / in
273.0
10.750
323.9
12.750
267.4
10.528
318.5
12.539
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
558.8
22.000
609.6
24.000

Pipe End
Separation
mm / in
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13
0-3.2
0-0.13


A
mm / in
318
12.52
374
14.72
316
12.44
370
14.57
397
15.63
461
18.15
514
20.24
571
22.48
622
24.49
673
26.47

16" ~ 18"

20" ~ 24"

Dimensions
Bolt
B
C
Size
mm / in
mm / in
No.
in
406
65

2
x 6
15.98
2.56
452
65

2
x 6
17.78
2.56
425
64

2
x 6
16.73
2.52
465
64

2
x 6
18.31
2.52
500
75

2
x 6
19.69
2.95
536
75

6
x 3
21.10
2.95
587
75

6
x 3
23.11
2.95
669
79

8
x 4
26.34
3.11
720
79

8
x 4
28.35
3.11
771
79

8
x 4
30.35
3.11

Bolt
Torque
N-m / Lbs-Ft
145 235
105 - 175
145 235
105 - 175
145 235
105 - 175
145 235
105 - 175
145 235
105 - 175
68 - 100
50 - 75
68 - 100
50 - 75
85 200
65 - 150
85 200
65 - 150
85 200
65 - 150

Weight
Kgs / Lbs
10.5
23.1
11.5
23.3
8.5
18.7
9.8
21.6
15.0
33.0
19.4
42.7
25.0
55.0
33.1
72.8
33.0
72.6
34.7
76.3

Air Conditioning

Connect with the Best!

www.shurjoint.com

63
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SS-8 STAINLESS STEEL

Flexible Coupling

The Model SS-8 is a flexible coupling

(316) with 304 or 316 bolts and nuts. SS-8

designed for a variety of general service

couplings should always be installed so that

and specialty applications. The SS-8 is

the coupling bolt pads make metal to metal

supplied standard in CF8 (304) and CF8M

contact.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

25

1

32

1

40

1

50

2

65

2


76.1mm


80

3

100

4


139.7mm


125

5


165.1mm


150

6

200

8


200 JIS

64
Copyright 2011 Shurjoint

Pipe
O. D.
mm / in
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625
216.3
8.516

Pipe End
Separation
A
mm / in
mm / in
0 - 1.6
55.7
0 - 0.06
2.19
0 - 1.6
64.6
0 - 0.06
2.54
0 - 1.6
70.8
0 - 0.06
2.79
0 - 1.6
83.0
0 - 0.06
3.28
0 - 1.6
96.2
0 - 0.06
3.79
0 - 1.6
99.0
0 - 0.06
3.91
0 - 1.6
111.0
0 - 0.06
4.39
0 - 3.2
143.0
0 - 0.13
5.62
0 - 3.2
171.0
0 - 0.13
6.73
0 - 3.2
170.8
0 - 0.13
6.72
0 - 3.2
194.0
0 - 0.13
7.67
0 - 3.2
198.0
0 - 0.13
7.80
0 - 3.2
255.0
0 - 0.13
10.04
0 - 3.2
251.0
0 - 0.13
10.00

Connect with the Best!

Dimensions
Deflection
Bolt
B
C
Degree
Size
Weight
mm / in
mm / in
( )
in
Kgs / Lbs
87.5
44.0

0.5
5/16 x1
2 - 45
3.45
1.73
1.1
97.8
44.0

0.5
5/16 x1
2 - 10
3.85
1.73
1.1
105.1
44.0

0.5
5/16 x1
1 - 54
4.14
1.73
1.1
124.0
44.0

0.7
1 - 31
x2
4.88
1.73
1.5
139.9
44.0

0.8
1 - 15
x2
5.51
1.73
1.8
145.0
44.0

0.8
1 - 12
x2
5.71
1.73
1.8
157.0
44.0

1.0
1 - 02
x2
6.18
1.73
2.2
200.0
50.0

1.7
1 - 36
x3
7.87
1.97
3.7
231.0
50.0

2.2
1 - 18
x3
9.09
1.97
4.8
226.1
50.0

2.2
1 - 18
x3
8.90
1.97
4.8
253.0
53.0

2.7
1 - 07
x3
9.96
2.09
5.9
253.1
53.0

2.9
1 - 05
x3
9.96
2.09
6.4
337.0
62.0

6.4
0 - 50
x 3
13.27
2.44
14.1
346.0
60.0

5.1
0 - 51
x 3
13.62
2.40
11.3

www.shurjoint.com

Catalog 2011

MODEL

SS-8X Stainless Steel

Heavy Duty Flexible Coupling


The Model SS-8X is designed for high

(254SMO*). The SS-8X features 316 bolts,

pressure applications including reverse

washers and Silicon Bronze nuts to help

osmosis and desalination systems. The

prevent galling during repetitive use.

SS-8X is available in Duplex CD3MN

The SS-8X is also available in CF8M (316)

(2205), Super Duplex CE8MN, CE3MN

with 316 bolts and nuts. Contact Shurjoint

(2507) and 6-Moly stainless steel CK3MCuN

for details.

Pressure-Temperature Rating



Size
Nom. Rating




Working Pressure
(S40S, Cut-grooved)

Test Pressure
(Hydrostatic)

3/4 4

1400 psi @100F

2100 psi

98 Bar @38C

147 Bar

EPDM: 230F / 110C

5 8

1000 psi @100F

1500 psi

Nitrile: 180F / 82C

70 Bar @38C

10.5 MPa


CWP
20 - 100


CWP
125 - 200

Max. Service
Temperature

*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only.


*Burst pressure is engineered minimum 2 times the working pressure.s


Nominal

Size

mm / in

20



25

1

32

1

40

1

50

2

65

2

80

3

100

4

125

5

150

6

200

8


200 JIS

Pipe
O. D.
mm / in
26.7
1.050
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
216.3
8.516

Pipe End
Separation
A
mm / in
mm / in
0 - 1.6
56.0
0 - 0.06
2.20
0 - 1.6
63.0
0 - 0.06
2.45
0 - 1.6
72.0
0 - 0.06
2.82
0 - 1.6
78.0
0 - 0.06
3.06
0 - 1.6
88.0
0 - 0.06
3.46
0 - 1.6
153.0
0 - 0.06
6.02
0 - 1.6
120.0
0 - 0.06
4.71
0 - 3.2
152.0
0 - 0.13
5.98
0 - 3.2
181.0
0 - 0.13
7.13
0 - 3.2
208.0
0 - 0.13
8.19
0 - 3.2
267.0
0 - 0.13
10.53
0 - 3.2
264.0
0 - 0.13
10.39

Dimensions
Deflection
Bolt
B
C
Degree
Size
Weight
mm / in
mm / in
( )
in
Kgs / Lbs
95.0
46.0


0.7
3 - 23
x 2
3.75
1.81
1.5
99.0
46.0


0.8
2 - 45
x 2
3.91
1.81
1.8
111.0
46.0


0.9
2 - 10
x 2
4.37
1.81
2.0
123.0
46.0


1.0
1 - 54
x 2
4.82
1.81
2.2
134.0
47.0


1.2
1 - 31
x 2
5.28
1.85
2.6
103.0
47.0


1.3
1 - 15
x 2
4.06
1.85
2.9
171.0
47.0


1.8
1 - 02
x3
6.74
1.85
4.0
201.0
52.0


2.4
1 - 36
x3
7.90
2.03
5.3
249.0
53.0


3.5
1 - 18
x 3
9.80
2.09
7.7
276.0
53.0


4.0
1 - 05
x 3
10.85
2.09
8.8
341.0
62.0


6.8
0 - 50
x 4
13.43
2.44
15.0
338.0
62.0


6.5
0 - 51
x 4
13.31
2.44
14.3

Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods.

Reverse osmosis plant

Connect with the Best!

www.shurjoint.com

65
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SS-1200 Stainless Steel

High Pressure Flexible Coupling


The Model SS-1200 is designed for high

(2205), Super Duplex CE8MN, CE3MN

pressure applications including reverse

(2507) and 6-Moly stainless steel CK3MCuN

osmosis, desalination and other specialty

(254SMO*). The SS-1200 features 316

systems. The SS-1200 is available in strong

bolts, washers and Silicon Bronze nuts to

and anti-corrosive alloys of Duplex CD3MN

help prevent galling during repetitive use.

Pressure-Temperature Rating


Nom. Rating



CWP

Working Pressure
(S40S, Cut- or Roll-grooved)

Test Pressure
(Hydrostatic)

Max. Service
Temperature

1200 psi @100F


84 Bar @38C

1800 psi
126 Bar

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only.


*Burst pressure is engineered minimum 2 times the working pressure.

Nominal
Size
mm / in
20

25
1
32
1
40
1
50
2
65
2
80
3
100
4

Pipe
O. D.
mm / in
26.7
1.050
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500

Pipe End
Separation
mm / in
0 - 1.6
0 - 0.06
0 - 1.6
0 - 0.06
0 - 1.6
0 - 0.06
0 - 1.6
0 - 0.06
0 - 1.6
0 - 0.06
0 - 1.6
0 - 0.06
0 - 1.6
0 - 0.06
0 - 3.2
0 - 0.13


A
mm / in
53
2.09
60
2.36
70
2.76
76
2.99
88
3.46
102
4.02
119
4.69
152
5.98

Dimensions
Deflection
Bolt Size
B
C
Degree
mm / in
mm / in
( )
No.
in
94
46

3 - 23
2
x2
3.70
1.81
101
46

2 - 45
2
x2
3.98
1.81
111
46

2 - 10
2
x2
4.37
1.81
117
46

1 - 54
2
x2
4.61
1.81
137
49

1 - 31
2
x3
5.39
1.85
151
49

1 - 15
2
x3
5.94
1.85
168
49

1 - 02
2
x3
6.61
1.85
207
52

1 - 36
2
x 3
8.15
2.03

Weight
Kgs / Lbs
0.45
0.99
0.55
1.21
0.63
1.39
0.70
1.54
1.04
2.29
1.38
3.04
1.55
3.41
2.13
4.69

Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods.

The Shurjoint Fast-Fit gasket has been

with ANSI/NSF 61 for potable water (Cold

designed and engineered for easier and

Water +86F / 30C and Hot Water +180F

faster installations. The pipe-end friendly

/ +82C).

design eliminates struggling to stretch the


gasket over the pipe ends and the Fast-Fit

Always use the factory supplied Shurjoint

gasket also features Shurjoints Gap-Seal

Fast-Fit gasket. Performance standards do

technology, which seals the gap between

not support the use of a standard gasket in

the pipe ends and eliminates stagnant water

the SS-1200 coupling.

pockets within the gasket cavity. The FastFit gasket is UL classified in accordance

* 254SMO is a registered trademark of AvestaPolarit AB.

66
Copyright 2011 Shurjoint

Connect with the Best!

Fast-Fit Gasket:
Easy installation
with a single hand

Always use the Shurjoint Fast-fit gasket.


Don't use a standard gasket with the SS1200 coupling.

www.shurjoint.com

Catalog 2011

MODEL

SS-28 Stainless Steel HINGED LEVER COUPLING


The Model SS-28 Hinged Grooved

grooved pipe. Housings 40mm - 100mm

Coupling is designed for quick connect and

(1- 4) feature a smooth outer surface,

disconnect services. The housing segments

housings 125mm - 300mm (5 - 12) feature

are hinged with a lever handle for easy

a cross-ribbed design for added strength.

assembly. Use of the split pin can prevent

Standard gasket: Grade E EPDM or Grade

the accidental opening of the coupling. The

T Nitrile.

Model SS-28 can be used in a wide variety

Available standard in CF8 (304) or CF8M

of applications with standard roll- or cut-

(316).

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(STD, Roll-Grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
*Proof test pressure: 1.5 times the working pressure, non-shock cold water.
*Burst pressure is engineered minimum 3 times the working pressure.


Nominal

Size

mm / in

40

1

50

2

65

2


76.1mm


80

3

100

4

125

5

125

5


165.1mm


150

6

Pipe
O. D.
mm / in
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625

Max. Working
Pressure
Bar / PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Axial
Displacement
A
mm / in
mm / in
0 1.6
75
0 0.06
2.95
0 1.6
86
0 0.06
3.39
0 1.6
92
0 0.06
3.62
0 1.6
92
0 0.06
3.62
0 1.6
119
0 0.06
4.69
0 3.2
165
0 0.13
6.50
0 3.2
189
0 0.13
7.44
0 3.2
189
0 0.13
7.44
0 3.2
213
0 0.13
8.39
0 3.2
216
0 0.13
8.50

split pin

Dimensions
B
mm / in
118
4.65
121
4.76
150
5.91
150
5.91
163
6.42
205
8.07
253
9.96
253
9.96
278
10.94
281
11.06


Deflection
C
Degree
Weight
mm / in
( )
Kgs / Lbs
47

1.0
3 - 48'
1.85
2.2
48

1.1
3 - 31'
1.89
2.4
48

1.4
2 - 30'
1.89
3.1
48

1.4
2 - 24'
1.89
3.1
48

1.8
2 - 24'
1.89
4.0
52

2.7
3 - 12'
2.05
5.9
52

4.9
2 - 37'
2.05
10.8
52

4.9
2 - 36'
2.05
10.8
52

5.8
2 - 14'
2.05
12.8
52

5.8
2 - 10'
2.05
12.8

*Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.

Expansion Pipe

Lever handles are factory assembled tight


for safety. The use of an expansion pipe will
aid the easy opening and closing. Expansion
pipes are available upon request.

Connect with the Best!

www.shurjoint.com

67
Copyright 2011 Shurjoint

CAST GROOVED FITTINGS


MODEL

Catalog 2011

MODEL

SS-10 90 ELBOW
SS-11 45 ELBOW

SS-20
SS-60

The Shurjoint Model SS-10, SS-11,

and CF8M (316). In addition fittings are

service requirements.
All cast fittings feature full flow

TEE
CAP

SS-20 and SS-60 stainless steel grooved

also available on request in CF3M (316L),

fittings are investment cast in sizes 1" -

316Ti, 2205 Duplex, 2507 Super Duplex and

characteristics and are designed to the

12". These fittings are supplied in ASTM

ASTM CK-3MCuN (UNS J93245) the cast

same C - E dimensions of standard ductile

A351 or A743 austenitic grades CF8 (304)

equivalent to 254SMO* to meet your specific

iron grooved fittings.

Pressure-Temperature Rating

Working Pressure
Size
Nom. Rating

(STD, Roll-grooved)
1 - 4

Class 300
25 - 100
5 12

Class 250
125 - 300

750 psi @100F


52 Bar @38C
400 psi @100F
28 Bar @38C

Max. Service
Temperature
EPDM: 230F / 110C
Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.

-E

C-E

C-E

E-E
E-E

C-E


Nominal

Size

mm / in

25

1

32

1

40

1

50

2

65

2


76.1 mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6

200

8

250

10

300

12


200 JIS



250 JIS



300 JIS

Pipe
O. D.
mm / in
33.4
1.315
42.2
1.660
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
165.1
6.500
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750
216.3
8.516
267.4
10.528
318.5
12.539

SS-10 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
57
0.3
2.25
0.7
70
0.4
2.75
0.9
70
0.4
2.75
0.9
83
0.6
3.25
1.3
95
1.4
3.75
3.1
95
1.6
3.75
3.5
108
1.3
4.25
2.9
127
2.2
5.00
4.8
140
3.9
5.50
8.6
140
3.9
5.50
8.6
165
6.2
6.50
13.6
165
6.5
6.50
14.3
197
10.7
7.75
23.5
229
29.0
9.00
63.8
254
38.0
10.00
83.6
197
10.7
7.75
23.5
238
29.0
9.37
63.8
310
21.7
12.20
47.7

SS-11 45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
45
0.2
1.75
0.4
45
0.3
1.75
0.7
45
0.4
1.75
0.9
51
0.5
2.00
1.1
57
1.0
2.25
2.2
57
1.0
2.25
2.2
64
1.0
2.50
2.2
76
1.6
3.00
3.5
83
2.8
3.25
6.2
83
2.9
3.25
6.4
89
4.1
3.50
9.0
89
4.2
3.50
9.2
108
7.1
4.25
15.6
121
16.8
4.75
37.0
133
19.6
5.25
43.1
108
7.1
4.25
15.6
121
16.8
4.75
37.0
133
19.6
5.25
43.1

SS-20 Tee
C - E
Weight
mm / in
Kgs / Lbs
57
0.4
2.25
0.9
70
0.7
2.75
1.5
70
0.8
2.75
1.8
83
1.1
3.25
2.4
95
2.5
3.75
5.5
95
2.5
3.75
5.5
108
2.1
4.25
4.6
127
3.4
5.00
7.5
140
5.6
5.50
12.3
140
5.8
5.50
12.8
165
9.0
6.50
19.8
165
9.7
6.50
21.3
197
18.8
7.75
41.4
229
21.1
9.00
46.4
254
43.0
10.00
94.6
197
13.8
7.75
30.4
229
19.8
9.00
43.6
254
27.1
10.00
59.6

*254SMO is a registered trademark of Avesta Polarit AB.

68
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

SS-60 Cap
E - E
mm / in
24
0.94
24
0.94
24
0.94
24
0.94
45
1.75
45
1.75
51
2.00
51
2.00
60
2.38
60
2.38
76
3.00
76
3.00
90
3.50
127
5.00
145
5.71
90
3.50
127
5.00
145
5.71

Weight
Kgs / Lbs
0.1
0.2
0.1
0.2
0.2
0.4
0.2
0.4
0.4
0.9
0.4
0.9
0.7
1.5
0.9
2.0
1.6
3.5
1.5
3.3
2.6
5.7
2.4
5.3
5.2
11.4
10.2
22.4
14.7
32.3
5.2
11.4
8.9
19.6
14.7
32.3

MODEL

SS-21 REDUCING TEE

Catalog 2011

MODEL

SS-50 CONCENTRIC REDUCER

The Shurjoint Model SS-21 and SS-50


stainless steel fittings are investment cast in
sizes to 8" and sand cast or wrought in sizes
10"-24".

C-E

C-B

Nominal

Size
mm / in

40 x 25

1x 1

40 x 32
1 x 1

50 x 25

2 x 1

50 x 32

2 x 1

50 x 40

2 x 1

65 x 25

2 x 1

65 x 32
2 x 1

65 x 40
2x 1

65 x 50

2 x 2


76.1 mm x 25



76.1mm x 32



76.1 mm x 40



76.1mm x 50


80 x 32

3 x 1

80 x 40

3 x 1

80 x 50

3 x 2

80 x 65

3 x 2


80 x 76.1mm

100 x 50

4 x 2
100 x 65

4 x 2


100 x 76.1mm

100 x 80

4 x 3

Pipe
SS-21 Reducing Tee
SS-50 Concentric Reducer
O. D.
C-E
C-B
Weight
E - E
Weight
mm / in
mm / in mm / in Kgs / Lbs
mm / in
Kgs / Lbs
48.3 x 33.483
83
83
0.6
64
0.3
1.900 x 1.315
3.25
3.25
1.3
2.50
0.6
48.3 x 42.283
83
83
0.6
64
0.3
1.900 x 1.660
3.25
3.25
1.3
2.50
0.7
60.3 x 33.483
83
83
0.7
64
0.3
2.375 x 1.315
3.25
3.25
1.5
2.50
0.8
60.3 x 42.283
83
83
0.8
64
0.7
2.375 x 1.660
3.25
3.25
1.8
2.50
0.7
60.3 x 48.383
83
83
0.8
64
0.3
2.375 x 1.900
3.25
3.25
1.8
2.50
0.7
73.0 x 33.495
95
95
0.9
64
0.4
2.875 x 1.315
3.74
3.74
2.0
2.50
0.9
73.0 x 42.295
95
95
0.9
64
0.5
2.875 x 1.660
3.74
3.74
2.0
2.50
1.1
73.0 x 48.395
95
95
0.9
64
0.5
2.875 x 1.900
3.74
3.74
2.0
2.50
1.2
73.0 x 60.395
95
95
1.5
64
0.5
2.875 x 2.375
3.74
3.74
3.3
2.50
1.1
76.1 x 33.495
95
95
0.9
64
0.4
3.000 x 1.315
3.74
3.74
2.0
2.50
0.9
76.1 x 42.295
95
95
0.9
64
0.5
3.000 x 1.660
3.74
3.74
2.0
2.50
1.1
76.1 x 48.395
95
95
0.9
64
0.5
3.000 x 1.900
3.74
3.74
2.0
2.50
1.2
76.1 x 60.395
95
95
1.5
64
0.5
3.000 x 2.375
3.74
3.74
3.3
2.50
1.1
88.9 x 42.2108
108
108
1.6
64
0.5
3.500 x 1.660
4.25
4.25
3.5
2.50
1.1
88.9 x 48.3108
108
108
1.3
64
0.6
3.500 x 1.900
4.25
4.25
2.9
2.50
1.5
88.9 x 60.3108
108
108
2.1
64
0.6
3.500 x 2.375
4.25
4.25
4.6
2.50
1.3
88.9 x 73.0108
108
108
2.1
64
1.0
3.500 x 2.875
4.25
4.25
4.6
2.50
2.2
88.9 x 76.1108
108
108
2.1
64
1.0
3.500 x 3.000
4.25
4.25
4.6
2.50
2.2
114.3 x 60.3
127
127
3.3
76
1.0
4.500 x 2.375
5.00
5.00
7.3
3.00
2.2
114.3 x 73.0
127
127
3.3
76
1.4
4.500 x 2.875
5.00
5.00
7.3
3.00
3.1
114.3 x 76.1
127
127
3.3
76
1.4
4.500 x 3.000
5.00
5.00
7.3
3.00
3.1
114.3 x 88.9
127
127
3.2
76
0.9
4.500 x 3.500
5.00
5.00
7.0
3.00
2.0

Connect with the Best!

Nominal

Size
mm / in
125 x 100

5 x 4
125 x 100

5 x 4


165.1mm x 80



165.1mm x 100

165.1mm
x 139.7mm
150 x 80

6 x 3
150 x 100

6 x 4
150 x 125

6 x 5
200 x 100

8 x 4
200 x 125

8 x 5
200 x 150

8 x 6
250 x 150

10 x 6
250 x 200

10 x 8
300 x 200

12 x 8
300 x 250

12 x 10


200 JIS x 100



200 JIS x 125


200 JIS
x 165.1mm

250 JIS
x 165.1mm

250 JIS
x 200 JIS

300 JIS
x 200 JIS

300 JIS
x 250 JIS

E-E

Pipe
SS-21 Reducing Tee
SS-50 Concentric Reducer
O. D.
C-E
C-B
Weight
E - E
Weight
mm / in
mm / in mm / in Kgs / Lbs
mm / in
Kgs / Lbs
139.7 x 114.3
140
140
5.1
89
1.6
5.500 x 4.500
5.50
5.50
11.2
3.50
3.5
141.3 x 114.3
140
140
5.1
89
1.6
5.563 x 4.500
5.50
5.50
11.2
3.50
3.5
165.1 x 88.9
165
165
7.0
102
2.3
6.500 x 3.500
6.50
6.50
15.4
4.00
5.1
165.1 x 114.3
165
165
8.4
102
2.3
6.500 x 4.500
6.50
6.50
18.5
4.00
5.1
165.1 x 139.7
165
165
8.8
102
2.6
6.500 x 5.500
6.50
6.50
19.4
4.00
5.7
168.3 x 88.9
165
165
7.1
102
2.3
6.625 x 3.500
6.50
6.50
15.6
4.00
5.1
168.3 x 114.3
165
165
8.8
102
2.3
6.625 x 4.500
6.50
6.50
19.4
4.00
5.1
168.3 x 141.3
165
165
8.8
102
2.6
6.625 x 5.563
6.50
6.50
19.4
4.00
5.7
219.1 x 114.3
197
197
16.1
127
4.3
8.625 x 4.500
7.76
7.76
35.4
5.00
9.5
219.1x 141.3
197
197
13.0
127
5.4
8.625 x 5.563
7.76
7.76
28.6
5.00
11.9
219.1 x 168.3
197
197
24.6
127
4.3
8.625 x 6.625
7.76
7.76
54.1
5.00
9.5
273.0 x 168.3
229
229
26.9
152
8.3
10.750 x 6.625
9.02
9.02
59.2
6.00
18.3
267.4 x 216.3
229
229
27.3
152
8.7
10.528 x 8.516
9.02
9.02
60.1
6.00
19.1
323.9 x 219.1
254
254
25.5
178
22.0
12.750 x 8.625 10.00
10.00
56.1
7.00
49.5
323.9 x 273.0
254
254
26.0
178
11.3
12.750 x 10.750 10.00
10.00
57.2
7.00
23.1
216.3 x 114.3
197
197
16.1
127
4.3
8.516 x 4.500
7.76
7.76
35.4
5.00
9.5
216.3 x 139.7
197
197
12.7
127
5.4
8.516 x 5.500
7.76
7.76
27.9
5.00
11.9
216.3 x 165.1
197
197
12.6
127
4.3
8.516 x 6.500
7.76
7.76
27.7
5.00
9.5
267.4 x 165.1
229
229
26.9
152
8.3
10.528 x 6.500
9.0
9.02
59.2
6.00
18.3
267.4 x 216.3
229
229
27.3
152
8.7
10.528 x 8.516
9.02
9.02
60.1
6.0
19.1
318.5 x 216.3
254
254
25.5
178
22.0
12.539 x 8.516 10.00
10.00
56.1
7.00
49.5
318.5 x 267.4
254
254
26.0
178
11.3
12.539 x 110.528 10.00
10.00
57.2
7.00
23.1

www.shurjoint.com

69
Copyright 2011 Shurjoint

WROUGHT STAINLESS STEEL FITTINGS

Catalog 2011

MODEL

WS-10 90 ELBOW, S/R WS-10L 90 ELBOW, L/R WS-11 45 ELBOW, L/R


WS-20 EQUAL TEE
WS-60 CAP
Shurjoint wrought stainless steel grooved
fittings are fabricated from Sch. 10S

E-E

stainless steel pipe to ASTM A403 WP-S

C-E

C-E

304 or 316, or welded pipe or plate WP-W.


C-E dimensions conform to ANSI B16.9 and
B16.28.












WS-10

Nominal
Size
mm / in
350
14
400
16
450
18
500
20
600
24

Pipe
O.D.
mm / in
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000

WS-10
C-E
Weight
mm / in
Kgs / Lbs
355.6
23.59
14.00
51.90
406.4
30.84
16.00
67.85
457.2
40.43
18.00
89.15
508.0
54.90
20.00
121.05
609.6
93.55
24.00
206.27

WS-10L
C-E
Weight
mm / in
Kgs / Lbs
533.4
36.30
21.00
79.86
609.6
47.63
24.00
104.79
685.8
59.87
27.00
131.71
762.0
99.79
30.00
219.54
914.4
140.61
36.00
309.34

C-E

C-E
WS-10L

WS-11

WS-11
C-E
Weight
mm / in
Kgs / Lbs
222.3
18.14
8.75
39.91
254.0
23.81
10.00
52.38
285.5
29.94
11.25
65.87
317.5
49.89
12.50
109.76
381.0
70.31
15.00
154.68

C-E
WS-20

WS-20
C-E
Weight
mm / in
Kgs / Lbs
279.4
48.53
11.00
106.77
304.8
58.97
12.00
129.73
342.9
76.66
13.50
168.65
381.0
103.42
15.00
227.52
431.8
155.58
17.00
342.28

WS-60
WS-60
E-E
Weight
mm / in
Kgs / Lbs
165.0
8.16
6.50
17.95
178.0
14.51
7.00
31.92
203.0
17.96
8.00
39.51
229.0
27.22
9.00
59.88
267.0
34.47
10.50
75.83

MODEL

WS-21 REDUCING TEE


Material: ASTM A403 WP-S 304 or 316
Wall thickness: Sch. 10S
C-E & C-B dimensions: ANSI B16.9 &
B16.28

C-E
C-B

WS-21

Nominal Pipe
Size
mm / in
350 x 150
14 x 6
350 x 200
14 x 8
350 x 250
14 x 10
350 x 300
14 x 12
400 x 150
16 x 6
400 x 200
16 x 8
400 x 250
16 x 10
400 x 300
16 x 12
400 x 350
16 x 14

Pipe
O.D.
mm / in
355.6 x 168.3
14.000 x 6.625
355.6 x 219.1
14.000 x 8.625
355.6 x 273.0
14.000 x 10.750
355.6 x 323.9
14.000 x 12.750
406.4 x 168.3
16.000 x 6.625
406.4 x 219.1
16.000 x 8.625
406.4 x 273.0
16.000 x 10.750
406.4 x 323.9
16.000 x 12.750
406.4 x 355.6
16.000 x 14.000

WS-21 Reducing Tee


C-E
C-B
mm / in
mm / in
279.0
238.0
11.0
9.37
279.0
248.0
11.0
9.76
279.0
257.0
11.0
10.12
279.0
270.0
11.0
10.63
305.0
264.0
12.0
10.40
305.0
273.0
12.0
10.75
305.0
282.0
12.0
11.10
305.0
295.0
12.0
11.61
305.0
305.0
12.0
12.00

Weight
Kgs / Lbs
22.19
48.92
23.82
52.52
25.11
55.37
27.16
59.88
27.79
61.28
29.46
64.95
30.87
68.06
33.08
72.95
34.95
77.06

MODEL

WS-50 Concentric

Reducer

Material: ASTM A403 WP-S 304 or 316


Wall thickness: Sch. 10S
E-E dimensions: ANSI B16.9 & B16.28

E-E
WS-50

70
Copyright 2011 Shurjoint

Connect with the Best!

Nominal Pipe
Size
mm / in
350 x 150
14 x 6
350 x 200
14 x 8
350 x 250
14 x 10
350 x 300
14 x 12
400 x 150
16 x 6
400 x 200
16 x 8
400 x 250
16 x 10
400 x 300
16 x 12
400 x 350
16 x 14

Pipe
O.D.
mm / in
355.6 x 168.3
14.000 x 6.625
355.6 x 219.1
14.000 x 8.625
355.6 x 273.0
14.000 x 10.750
355.6 x 323.9
14.000 x 12.750
406.4 x 168.3
16.000 x 6.625
406.4 x 219.1
16.000 x 8.625
406.4 x 273.0
16.000 x 10.750
406.4 x 323.9
16.000 x 12.750
406.4 x 355.6
16.000 x 14.000

WS-50 Concentric Reducer


E-E
Weight
mm / in
Kgs / Lbs
279.0
12.6
11.0
27.8
279.0
14.6
11.0
32.1
279.0
17.1
11.0
37.8
279.0
20.3
11.0
44.7
305.0
16.1
12.0
35.5
305.0
18.2
12.0
40.2
305.0
21.0
12.0
46.2
305.0
22.8
12.0
50.3
305.0
26.7
12.0
58.9

www.shurjoint.com

Catalog 2011

MODEL

SS-41 FLANGE

ADAPTER - ANSI 125/150

The Model SS-41 stainless steel flange

(316). Integral closure tabs located on

adapter allows for a direct connection with

the flange OD help facilitate alignment and

ANSI Class 125/150 flanges. The SS-41 is

assembly.

investment cast in Gr. CF8 (304) or CF8M




Nom. Rating



Class 150

Pressure-Temperature Rating
Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

D E

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
150
6
200
8

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
168.3
6.625
219.1
8.625

Max. Working
Pressure
Bar / PSI
20
300
20
300
20
300
20
300
20
300
20
300

Max. End
Load
A
kN / Lbs
mm / in
5.71
152
1330
6.00
8.37
178
1950
7.00
12.41
190
2880
7.50
20.51
229
4770
9.00
44.47
279
10340
11.00
75.37
343
17520
13.50

Dimensions
B
C
mm / in
mm / in
121
21
4.75
0.83
140
22
5.50
0.87
152
24
6.00
0.94
191
24
7.50
0.94
241
25
9.50
1.00
298
28
11.75
1.12

Sealing Surface
Bolts
D
E
Size.
mm / in
mm / in
No.
in
60
87

4
x3
2.36
3.42
73
102

4
x3
2.87
4.00
89
116

4
x3
3.50
4.56
114
141

8
x3
4.50
5.56
168
198

8
x 3
6.62
7.79
219
254

8
x 3
8.62
10.00

Weight
Kgs / Lbs
2.1
4.6
2.7
6.0
3.1
6.8
4.5
9.9
5.8
12.9
9.2
20.2

* Based on Sch. 10S pipe.

MODEL

SS-80 STAINLESS STEEL

Universal Flange Adapter

The Model SS-80 Universal Flange Adapter

Pressure-Temperature Rating

provides for a rigid transition between a



Nom. Rating

grooved piping system and a flanged piping


system or component. The SS-80 can mate
to ANSI 125/150, PN 10/16, BS-10E or JIS
10K, and is available standard in CF8 (304)
or CF8M (316).
Nominal

Size

mm / in

50

2

65

2


76.1 mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6

200

8


200 JIS



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.

X Y

L
Pipe O. D.
Y: Flange Drilling
Basic
ANSI 125 / 150
PN 10, 16
JIS 10K
Z
mm / in
L
X
mm / in
mm / in
mm / in
mm / in
60.3
64
165
121
125
120
16
2.375
2.50
6.50
4.75
4.92
4.72
0.63
73.0
70
185
140
145
140
16
2.875
2.75
7.28
5.50
5.70
5.50
0.63
76.1
76
185
140
145
140
16
3.000
3.00
7.28
5.50
5.70
5.50
0.63
88.9
76
200
152
160
150
16
3.500
3.00
7.78
6.00
6.30
5.90
0.63
114.3
76
220
191
180
175
16
4.500
3.00
8.66
7.50
7.09
6.89
0.63
139.7
76
254
216
210
210
22
5.500
3.00
10.00
8.50
8.27
8.27
0.87
141.3
89
254
216
210
210
22
5.563
3.50
10.00
8.50
8.27
8.27
0.87
165.1
76
270
241
240
240
16
6.500
3.00
10.63
9.50
9.45
9.45
0.63
168.3
89
291
241
240
240
24
6.625
3.50
11.46
9.50
9.45
9.45
0.94
219.1
102
343
298
295

29
N/A
8.625
4.00
13.50
11.75
11.61
1.14
216.3
102
343
298
295

23
N/A
8.516
4.00
13.50
11.75
11.61
0.91

Bolt
Size
mm / in
No.
M16
4

4
M16
4

4
M16
4

4
M16
8

8
M16
8

8
M16 / M20
8
/
8
M16 / M20
8
/
8
M20
8

8
M20
8

8
M20
8 / 12

8 / 12
M20
8 / 12

8 / 12

Weight
Kgs / Lbs
2.0
4.4
2.9
6.4
3.0
6.6
3.4
7.5
3.9
8.6
6.7
14.7
6.7
14.7
6.8
15.0
6.9
15.2
14.5
31.9
14.0
30.8

Contact Shurjoint for other sizes.

Connect with the Best!

www.shurjoint.com

71
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SS-723 STAINLESS STEEL MECHANICAL TEE


The Shurjoint Model SS-723 stainless steel

simply cut or drill a hole at the desired

mechanical tee is the ideal fitting for branch

location, position the housing so that the

or direct outlet connections to sprinkler

locating collar fits within the hole and secure

heads, drop nipples and or gauges on

with the bolts and nuts.

stainless steel pipe. No need for welding,


C

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on Sch. 40S pipe.


Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
32 x 15
1 x
32 x 20
1 x
32 x 25
1 x 1
40 x 15
1 x
40 x 20
1 x
40 x 25
1 x 1
50 x 15
2 x
50 x 20
2 x
50 x 25
2 x 1

Hole Dia.
+1.6, -0 / +0.063, -0
A
B
mm / in
mm / in
mm / in
30
41
26
1.18
1.60
1.02
30
44
26
1.18
1.70
1.02
30
51
26
1.18
2.00
1.02
30
44
29
1.18
1.70
1.13
30
46
29
1.18
1.81
1.13
30
53
29
1.18
2.09
1.13
30
51
36
1.18
2.00
1.42
30
53
36
1.18
2.09
1.42
30
60
36
1.18
2.37
1.42

Dimensions
C
D
mm / in
mm / in
87
49
3.44
1.93
87
49
3.44
1.93
87
49
3.44
1.93
90
49
3.54
1.93
90
49
3.54
1.93
90
49
3.54
1.93
109
51
4.28
2.00
109
51
4.28
2.00
109
51
4.28
2.00


Bolt
T*
Size
Weight
mm / in
in
Kgs / Lbs
27

0.3
5/16 x 1
1.06
0.7
29

0.3
5/16 x 1
1.14
0.7
34

0.4
5/16 x 1
1.34
0.9
30

0.3
5/16 x 1
1.18
0.7
31

0.3
5/16 x 1
1.22
0.7
36

0.4
5/16 x 1
1.42
0.9
37

0.5
5/16 x 1
1.46
1.1
28

0.5
5/16 x 1
1.10
1.1
43

0.6
5/16 x 1
1.69
1.4

T*: Take-out (Center of run to end of pipe to be engaged)

MODEL

SS-726 STAINLESS STEEL Y-STRAINER


The Model SS-726 Stainless Steel Grooved-

Cleaning and maintenance of the screen

end Y-Strainers are designed to strain debris

can be accomplished easily by removing

and foreign matter from piping systems

the coupling. The Model SS-726 Stainless

and thus provide inexpensive protection for

Steel Y-Strainer is suitable for vertical or

costly pumps, meters and other components.

horizontal installations.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
65
2
80
3
100
4
150
6

72
Copyright 2011 Shurjoint

Pipe
OD
mm / in
73.0
2.875
88.9
3.500
114.3
4.500
168.3
6.625

Max. Working
Pressure
A
bar / psi
mm / in
20
273
300
10.75
20
299
300
11.75
20
362
300
14.25
20
470
300
18.50

Connect with the Best!

Dimensions
B
C
mm / in
mm / in
199
122
7.83
4.80
221
129
8.70
5.08
269
168
10.59
6.61
357
219
14.05
8.62

Drain Plug
Size
mm / in
15

15

25
1
25
1

www.shurjoint.com

Weight
Kgs / Lb
7.6
16.7
8.6
18.9
9.6
21.1
39.0
85.8

Catalog 2011

MODEL

SJ-600L Ball Valve


The Model SJ-600L is a two-piece, full-port

torque and is supplied with a lever handle as

stainless steel ball valve rated at 600 psi (40

well as ISO mounting holes to accommodate

bar) and is available in CF8M (316). The

a full range of gear or power actuators.

SJ-600L features a floating ball for lower


Pressure-Temperature Rating


Nom. Rating

Working Pressure
(S40S, Roll-Grooved)

Shell Test
(Hydrostatic)

Max. Service
Temperature

600 psi @100F


42 Bar @38C

900 psi
63 Bar

EPDM: 230F / 110C


Nitrile: 180F / 82C



CWP

Size: 4"
W

*Working pressure is for connection with cut- or roll-grooved schedule Sch. 40S pipe.
*Seat test: 110% the working pressure.

H
d

L

Nominal

Size

mm / in

40

1

50

2

65

2


76.1 mm


80

3

100

4

Pipe
OD
mm / in
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500

Operating
Torque
L
Lb - in / N - m
mm / in
7
140
62
5.50
17
156
150
6.15
21
180
186
7.09
21
180
186
7.09
28
214
248
8.42
45
240
398
9.45

Size: 1" - 3"


H
mm / in
94
3.70
105
4.13
110
4.33
110
4.33
152
6.00
167
6.57

Dimensions
W
mm / in
193
7.60
193
7.60
250
9.84
250
9.84
250
9.84
290
11.42


d
mm / in
38
1.50
50
1.97
65
2.56
65
2.56
78
3.07
100
3.94

Approx.
Weight
Kgs / Lbs
3.0
6.6
4.0
8.8
7.0
15.4
7.0
15.4
9.4
20.7
25.0
55.0

* The weight includes the lever handle.

MODEL

SJ-600W Ball Valve


The Model SJ-600W is supplied with a worm

gear operator. The standard gear operator


is supplied with a bracket and extension

sleeve. Sizes available are 2"/50mm through


4"/100mm.


Nominal

Size

mm / in

50

2

65

2


76.1 mm


80

3

100

4

Pipe
OD
K
mm / in
mm / in
60.3
152
2.375
6
73.0
152
2.875
6
76.1
152
3.000
6
88.9
152
3.500
6
114.3
152
4.500
6

Dimensions
H
W
mm / in
mm / in
137
203
5.38
8
145
203
5.68
8
145
203
5.68
8
182
203
7.16
8
203
203
8.00
8

Approx.
Weight
Kgs / Lbs
8.10
17.82
11.10
24.42
11.10
24.42
13.50
29.70
29.0
63.80

* The weight includes the worm gear operator.

Connect with the Best!

www.shurjoint.com

73
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SJ-400 BUTTERFLY VALVE


The Shurjoint Model SJ-400 Butterfly Valve

(type 316) to ASTM A743 with integral neck

is a grooved end stainless steel butterfly

and ISO 5211 mounting pad. It features a

valve, supplied with a 10 position lever

dual seal disc encapsulated with Gr. E EPDM

handle (SJ-400-L) or worm gear operator

for cold and hot water services. The end-to-

(SJ-400-W). The body is available in CF8M

end dimensions conform to MSS SP-67.

Pressure-Temperature Rating


Nom. Rating



Class 150

Working Pressure
(S40S, Roll-grooved)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply
110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S
pipe and 50% for roll-grooved Sch. 5S pipe.
Seat test: 110% the working pressure.
Shell test: 1.5 times the working pressure.

SJ-400-W
14-24

E
E

SJ-400-L
2-12
F

D
O. D.

O. D.

B

Nominal

Size

mm / in

50

2

65

2


76.1 mm


80

3

100

4


165.1 mm


150

6

200JIS


200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

Pipe
O. D.
A
B
mm / in
mm / in
mm / in
60.3
81
64
2.375
3.19
2.520
73.0
97
80
2.875
3.81
3.150
76.1
97
80
3.000
3.81
3.150
88.9
97
92
3.500
3.81
3.622
114.3
116
118
4.500
4.56
4.646
165.1
148
172
6.500
5.81
6.772
168.3
148
172
6.625
5.81
6.772
216.3
133
222
8.516
5.24
8.740
219.1
133
222
8.625
5.24
8.740
273.0
160
284
10.750
6.30
11.18
323.9
166
334
12.750
6.56
13.15
355.6
178
359
14.000
7.00
14.13
406.4
178
410
16.000
7.00
16.14
457.2
203
464
18.000
8.00
18.25
508.0
216
515
20.000
8.50
20.28
609.6
254
616
24.000
10.00
24.25

SJ-400-W
Dimensions
C
D
mm / in
mm / in
63
106
2.480
4.17
68
111
2.677
4.28
68
111
2.677
4.28
76
126
2.992
4.97
89
135
3.504
5.33
114
168
4.488
6.62
114
184
4.488
7.25
140
208
5.512
8.20
140
208
5.512
8.20
186
235
7.32
9.25
213
260
8.39
10.24
224
276
8.82
10.87
248
302
9.76
11.89
283
350
11.14
13.78
314
383
12.36
15.08
368
453
14.50
17.83


E
mm / in
192
7.56
192
7.56
192
7.56
192
7.56
252
9.92
252
9.92
342
13.46
342
13.46
342
13.46
252
9.92
356
14.02
203
8.00
242
9.50
242
9.50
290
11.40
290
11.40

Operating
Torque
Weight
N-m / In - Lb
Kgs / Lbs
8.80
2.3
78
5.0
9.50
3.2
84
7.0
9.50
3.2
84
7.0
10.7
3.5
95
6.6
22.6
5.0
200
11.0
34.9
9.2
310
20.2
34.9
9.2
310
20.2
45.1
12.2
400
26.8
45.1
12.2
400
26.8
170
28.3
1500
31.3
226
40.0
2000
88.0
254
59.0
10.0
130.0
306
67.0
12.00
147.4
305
86.0
12.00
189.2
412
133.0
16.20
292.6
412
160.0
16.20
352.0

* The weight includes the lever handle or worm gear operator.

74
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Section 4
Valves and Flow Control
Components
Valves and Flow Control Components..............................76
SJ-200 Low-profile Butterfly Valve..................................................... 77
SJ-300N Butterfly Valve.................................................................... 78
SJ-300F Butterfly Valve (for Fire Protection)..................................... 79
SJ-500L / SJ-500W Ball Valves..................................................... 80
SJ-900 Swing Check Valve................................................................ 81
SJ-915 Dual Disc Check Valve.......................................................... 82
SJ-930 Horizontal Swing Check Valve............................................... 83
650N Expansion Joint......................................................................... 84
651 Expansion Joint........................................................................... 85
725F Suction Diffuser........................................................................ 86
726 Y-Strainer.................................................................................... 88
728 T-Strainer.................................................................................... 89
RCV Riser Check Valve (for Fire Protection)...................................... 90

Connect with the Best!

Catalog 2011

www.shurjoint.com

Catalog 2011

Valves and Flow


Control Components
Shurjoint offers a complete range
of grooved-end butterfly valves,
ball valves, check valves, suction
diffusers, strainers and expansion
joints. Grooved-end valves and
components can be installed 3 4
times faster than comparable flange
components. With the removal
of just a few bolts one can easily
access the system for cleaning,
maintenance, changes and or
system expansion.

SJ-300L Butterfly Valve


726 Y-Strainer
7110LR 90 Elbow
7180 Universal Flange Adapter
7041 Flange
7150 Concentric Reducer
SJ-900 Check Valve
7707 Flexible Coupling
Z07 Rigid Coupling
7721 Mechanical Tee with Pressure Gage

SJ-300L Butterfly Valve


725F Suction Diffuser
7041 Flange
7150 Concentric Reducer
SJ-915 Dual Disc Check Valve
7707 Flexible Coupling
Z07 Rigid Coupling
7721 Mechanical Tee with Pressure Gage

Model 726 Y-strainers, SJ-300N butterfly valves and SJ-900 check valves
used on a chill water system.

76
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

SJ-200 LOW-PROFILE BUTTERFLY VALVE


The Shurjoint Model SJ-200 Butterfly Valve

(Nitrile body liner). The Model SJ-200

is a low profile, grooved-end butterfly valve

features a fully rubber lined body with

designed for oil & gas, mining and other

316 stainless steel disc. The end to end

service applications. The working pressure

dimensions conform to MSS SP-67. The

is rated up to 232 psi / 1600 kPa and service

lever handle is equipped with a tamper

temperatures are rated to +180F / +82C

resistant locking device.

Pressure-Temperature Rating
Nom.

Rating

CWP

Working
Pressure

Shell
Test

232 psi @100F 350 psi


16 Bar @38C

24 Bar

Max. Service
Temperature
EPDM: 230F / 110C
Nitrile: 180F / 82C

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Seat test: 110% the working pressure.

Not Recommended for Steam.


C
O. D.
B
A














Nominal
Size
mm / in
50
2
65
2
80
3
100
4
150
6
200
8

Pipe
O. D.
A
mm / in
mm / in
60.3
81
2.375
3.19
73.0
97
2.875
3.82
88.9
97
3.500
3.82
114.3
116
4.500
4.57
168.3
148
6.625
5.83
219.1
133
8.625
5.25

Connect with the Best!

Dimensions
B
C
H
mm / in
mm / in
mm / in
48
57
140
1.89
2.25
5.51
54
67
190
2.13
2.65
7.48
62
75
190
2.44
2.94
7.48
76
97
274
3.00
3.82
10.79
104
116
274
4.09
4.57
10.79
140
152
274
5.50
6.00
10.79

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
0.9
2.0
1.5
3.3
1.9
4.2
3.9
8.6
10.1
22.2
11.3
27.9

77
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SJ-300N BUTTERFLY VALVE


The Shurjoint Model SJ-300N Butterfly

epoxy coated ductile iron body and EPDM or

Valve is a grooved-end shut-off valve

Nitrile (NBR) rubber encapsulated dual-seal

equipped with a 10 position lever handle

disc. The end-to-end dimensions conform to

(SJ-300N-L) or worm gear operator

MSS SP-67.

(SJ-300N-W). The valve consists of an


Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Shell
Test

Max. Service
Temperature

Class

300 psi @100F

450 psi

EPDM: 230F / 110C

20 Bar @38C

30 Bar

Nitrile: 180F / 82C

150

Dual-Seal

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Seat test: 110% the working pressure.

SJ-300N-W
w / worm gear
E
O

F
E

D
D

O. D.

O.D.

SJ-300N-L
w / lever handle
Nominal

Size
mm / in

50

2

65

2


76.1 mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6


200JIS


200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

Pipe
O.D.
A
B
mm / in
mm / in
mm / in
60.3
81
64
2.375
3.19
2.52
73.0
97
79
2.875
3.82
3.11
76.1
97
79
3.000
3.82
3.11
88.9
97
92
3.500
3.82
3.62
114.3
116
118
4.500
4.57
4.65
139.7
148
145
5.500
5.83
5.71
141.3
148
145
5.563
5.83
5.71
165.1
148
172
6.500
5.83
6.77
168.3
148
172
6.625
5.83
6.77
216.3
133
222
8.516
5.24
8.74
219.1
133
222
8.625
5.24
8.74
273.0
159
276
10.750
6.25
10.86
323.9
165
327
12.750
6.53
12.87
355.6
178
365
14.000
7.00
14.37
406.4
178
416
16.000
7.00
16.38
457.2
203
470
18.000
8.00
18.50
508.0
216
527
20.000
8.50
20.75
609.6
254
629
24.000
10.00
24.76

C
B
Dimensions
C
mm / in
63
2.48
68
2.68
68
2.68
76
2.99
89
3.50
102
4.02
102
4.02
114
4.49
114
4.49
140
5.51
140
5.51
170
6.69
205
8.07
224
8.82
248
9.76
283
11.14
314
12.36
368
14.49


Lever Handle Type
D
E
Operating Torque
Weight
mm / in
mm / in
N - m / In - Lb
Kgs / Lbs
106
192
9
3.1
4.17
7.56
80
6.8
111
192
14
3.7
4.37
7.56
120
8.2
111
192
14
3.8
4.37
7.56
120
8.4
126
192
18
4.1
4.96
7.56
160
9.0
135
260
51
5.2
5.32
10.24
450
11.4
168
260
79
7.7
6.61
10.24
700
16.9
168
260
79
7.7
6.61
10.24
700
16.9
184
260
102
9.2
7.24
10.24
900
20.2
184
260
102
9.2
7.24
10.24
900
20.2
208
260
136
12.2
8.19
10.24
1200
26.8
208
260
136
12.2
8.19
10.24
1200
26.8
235
356
204
22.0
9.25
14.02
1800
48.4
260
356
282
33.5
10.24
14.02
2500
73.7
276
---
---
---
10.86
---
---
---
302
---
---
---
11.89
350
---
---
---
13.78
---
---
---
383
---
---
---
15.08
---
---
---
453
---
---
---
17.83
---
---
---

Worm Gear Type


E
F
mm / in
mm / in
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
152
152
6.00
6.00
203
203
8.00
8.00
203
203
8.00
8.00
203
203
8.00
8.00
242
305
9.50
12.00
242
305
9.50
12.00
290
412
11.40
16.20
290
412
11.40
16.20

* The weight includes the lever handle or worm gear operator.

78
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Weight
Kgs / Lbs
6.2
13.6
6.5
14.3
6.5
14.3
7.3
16.0
8.7
19.1
9.9
21.8
9.9
21.8
11.4
25.0
11.5
25.3
14.5
31.9
14.5
32.0
27.0
59.4
33.5
73.7
59.0
130.0
67.0
147.4
86.0
189.2
133.0
292.6
160.0
352.0

Catalog 2011

SJ-300F BUTTERFLY VALVE


The Model SJ-300F Butterfly Valve is a

UL Specification 1091 and FM Approval

grooved-end shut-off valve equipped with

Standard 1112.

a weatherproof worm gear operator and

When the Model SJ-300F Butterfly Valve is

supervisory switch and wiring.

used in a fire protection piping, installation

The Model SJ-300F is FM approved for

shall conform to NFPA 13 and NFPA 72.

300 psi (20 Bar, 2.0 MPa) WWP (water

The valve consists of an epoxy powder

working pressure) service for indoor and

coated ductile iron body and EPDM rubber

outdoor use. Flow characteristics satisfy

encapsulated dual-seal disc.

Pressure-Temperature Rating
Nom.

Rating

CWP

Working
Pressure

Shell
Test

300 psi @100F 1500 psi


20 Bar @38C

105 Bar

Max. Service
Temperature

Model SJ-300F
Butterfly Valve

EPDM: 230F / 110C

Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Seat test: 2 times the working pressure.

O.D.
C
A


Nominal

Size

mm / in

65

2


76.1 mm


80

3

100

4


139.7mm


125

5


165.1 mm


150

6

Pipe
OD
A(1)
B
C
mm / in
mm / in
mm / in
mm / in
73.0
97
80
68
2.875
3.81
3.15
2.68
76.1
97
80
68
3.000
3.81
3.15
2.68
88.9
97
92
76
3.500
3.81
3.62
3.00
114.3
116
118
89
4.500
4.56
4.65
3.50
139.7
148
145
102
5.500
5.81
5.71
4.00
141.3
148
145
102
5.563
5.81
5.71
4.00
165.1
148
172
114
6.500
5.81
6.77
4.50
168.3
148
172
114
6.625
5.81
6.77
4.50

Dual Seal

Dimensions
D
mm / in
111
4.37
111
4.37
126
4.96
135
5.31
168
6.61
168
6.61
184
7.25
184
7.25

E
mm / in
210
8.27
210
8.27
233
9.17
255
10.04
301
11.85
301
11.85
329
12.95
329
12.95

F
mm / in
92
3.62
92
3.62
92
3.62
92
3.62
92
3.62
92
3.62
92
3.62
92
3.62

G
mm / in
163
6.42
163
6.42
163
6.42
163
6.42
163
6.42
163
6.42
163
6.42
163
6.42

Weight
Kgs / Lbs
8.8
17.9
8.8
17.9
9.2
20.3
10.6
23.4
14.3
31.6
14.4
31.6
16.1
35.5
16.1
35.5

(1) End to end dimensions conform to MSS SP-67.


(2) The weight includes the worm gear operator.

Connect with the Best!

www.shurjoint.com

79
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SJ-500L BALL VALVE


The Model SJ-500L is a ductile iron,

locking holes. The SJ-500L is comprised of

grooved-end, two-piece, regular port ball

a ductile iron body and end cap, virgin TFE

valve designed and tested in conformance

seats and chrome-plated carbon steel trim.

with MSS SP-110 and SP-72. The lever

Also available with stainless steel trim as an

handle is equipped with tamper resistant

option.

Pressure-Temperature Rating

Working
Pressure

Shell
Test




CWP

1 3
40 - 80
4" 6"
100 150

1000 psi @100F


70 Bar @38C
800 psi @100F
56 Bar @38C

1500 psi
105 Bar
1200 psi
84 Bar

Max. Service
Temperature

A
H

EPDM: 230F / 110C


Nitrile: 180F / 82C

Nominal

Size
mm / in

40

1

50

2

65

2


76.1 mm


80

3

100

4


165.1 mm


150

6

Pipe
O.D.
mm / in
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
165.1
6.500
168.3
6.625

Working
Pressure
Bar / Psi
70
1000
70
1000
70
1000
70
1000
70
1000
56
800
56
800
56
800

*Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel
pipe.
*Seat test: 110% the working pressure.

O. D.

Size
in / mm

O. D.

Nom.

Rating

1" - 4"

Operating
Torque*
L
H
W
N / m L b - in
mm / in
mm / in
mm / in
7
130
86
178
62
5.12
3.39
7.00
17
140
95
178
150
5.50
3.75
7.00
21
159
132
265
186
6.25
5.20
10.43
21
159
132
265
186
6.25
5.20
10.43
28
167
143
265
248
6.56
5.63
10.43
45
240
94
265
398
9.45
3.70
10.43
60
258
221
600
531
10.15
8.70
23.60
60
258
221
600
531
10.15
8.70
23.60

6"

Dimensions
d
A
B
C
mm / in
mm / in
mm / in
mm / in
32
15.9
7.9
45.1
1.25
0.625
0.312
1.775
38
15.9
7.9
57.2
1.50
0.625
0.312
2.250
50
15.9
7.9
69.1
2.00
0.625
0.312
2.720
50
15.9
7.9
72.3
2.00
0.625
0.312
2.845
63
15.9
7.9
84.9
2.50
0.625
0.312
3.344
90
15.9
7.9
110.0
3.50
0.625
0.312
4.334
125
15.9
9.5
163.9
4.92
0.625
0.374
6.453
125
15.9
9.5
163.9
4.92
0.625
0.374
6.453

Approx.
Weight
Kgs / Lbs
1.8
3.9
2.9
6.4
4.4
9.7
4.4
9.7
7.8
17.2
14.7
32.3
41.1
90.2
41.1
90.2

* When first opening or closing the valve when not continuosly operated.

MODEL

SJ-500W BALL VALVE WITH GEAR OPERATOR


The Model SJ-500W can be equipped with

a worm gear operator. The standard gear


operator is supplied with a bracket and
extension sleeve. The ISO 5211 mounting

K
K
H

pad allows for the mounting of power


actuators.
1" - 4"

Nominal

Size

mm / in

40

1

50

2

65

2


76.1 mm


80

3

100

4


165.1 mm


150

6

80
Copyright 2011 Shurjoint

Pipe
O. D.
K
mm / in
mm / in
48.3
152
1.900
6
60.3
152
2.375
6
73.0
152
2.875
6
76.1
152
3.000
6
88.9
152
3.500
6
114.3
152
4.500
6
165.1
305
6.500
12
168.3
305
6.625
12

Connect with the Best!

6"
Dimensions
H
W
mm / in
mm / in
124
203
4.88
8
137
203
5.38
8
145
203
5.68
8
145
203
5.68
8
182
203
7.16
8
203
203
8.00
8
277
356
10.89
14
277
356
10.89
14

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
7.0
15.4
8.0
17.6
10.0
22.0
10.0
22.0
14.0
30.8
33.0
72.6
56.0
123.2
56.0
123.2

Catalog 2011

MODEL

SJ-900 SWING CHECK VALVE


The Shurjoint Model SJ-900 Swing Check

a rated working pressure of 300 psi (20 bar),

Valve is a grooved-end check valve featuring

the valve can be installed in the horizontal or

a spring-loaded wide-open clapper and a

vertical position (upward flow only). Valves

non-stick leak tight EPDM rubber seal. With

are tested to API 598.

Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Shell
Test

Max. Service
Temperature

Class

300 psi @100F

450 psi

EPDM: 230F / 110C

20 Bar @38C

30 Bar

Nitrile: 180F / 82C

150

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Seat test: 110% the working pressure.


Nominal

Size

mm / in

65

2


76.1mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6

200

8

250

10

300

12


200 JIS



250 JIS



300 JIS

Pipe
O. D.
A
mm / in
mm / in
73.0
190
2.875
7.48
76.1
190
3.000
7.48
88.9
178
3.500
7.00
114.3
216
4.500
8.50
139.7
330
5.500
13.00
141.3
330
5.563
13.00
165.1
305
6.500
12.00
168.3
305
6.625
12.00
219.1
365
8.625
14.37
273.0
508
10.750
20.00
323.9
610
12.750
24.00
216.3
365
8.516
14.37
267.4
508
10.528
20.00
318.5
610
12.539
24.00

Connect with the Best!

Dimensions
B
C
mm / in
mm / in
114
95
4.50
3.75
114
95
4.50
3.75
114
95
4.50
3.75
146
117
5.75
4.60
210
178
8.25
7.00
210
178
8.25
7.00
210
178
8.25
7.00
210
178
8.25
7.05
260
217
10.23
8.54
365
273
14.37
10.75
398
327
15.67
12.87
260
217
10.23
8.54
365
273
14.37
10.75
398
327
15.67
12.87

www.shurjoint.com

Weight
Kgs / Lbs
5.0
11.0
4.9
10.8
4.9
10.8
8.3
18.3
23.5
51.7
23.5
51.7
23.5
51.7
23.5
51.7
45.3
99.7
99.0
217.8
155.6
342.3
45.3
99.7
98.5
216.7
155.6
342.3

81
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SJ-915 DUAL DISC CHECK VALVE


The Shurjoint Model SJ-915 is a grooved-

body with an EPDM or Nitrile (NBR) resilient

end dual-plate (or double-door) check

seat molded to the body and type 304

valve designed to provide positive and

stainless steel discs loaded with type 313

silent protection against backflow in piping

stainless steel springs.

systems. The valve features a ductile iron


B

Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Shell
Test

Max. Service
Temperature

Class

300 psi @100F

450 psi

EPDM: 230F / 110C

20 Bar @38C

30 Bar

Nitrile: 180F / 82C

150

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Seat test: 110% the working pressure.

Size: 2"~12"
C

Nominal
Size
mm / in
65
2
80
3
100
4
150
6
200
8
250
10
300
12

Pipe
O. D.
A
mm / in
mm / in
73.0
125
2.875
4.92
88.9
135
3.500
5.31
114.3
137
4.500
5.39
168.3
152
6.625
6.00
219.1
171
8.625
6.73
273.0
198
10.750
7.80
323.9
208
12.750
8.19

Dimensions
B
C
mm / in
mm / in
110
73
4.33
2.87
125
89
4.92
3.50
152
114
5.98
4.50
204
168
8.03
6.62
256
219
10.08
8.62
307
273
12.09
10.75
362
324
14.25
12.75

Approx.
Weight
Kgs / Lbs
2.3
5.0
2.5
5.5
3.8
8.4
7.6
11.7
12.4
27.3
20.7
45.5
28.3
62.2

The Shurjoint Model SJ-915 is also


available in sizes 14 to 24 / 350mm to
600mm. Face-to-face dimensions conform
to API 594 Class 150 and grooved ends to
ANSI/AWWA C606.
Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Shell
Test

Max. Service
Temperature

Class

250 psi @100F

400 psi

EPDM: 230F / 110C

17 Bar @38C

26 Bar

Nitrile: 180F / 82C

150

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Seat test: 110% the working pressure.

A
B
C

D
O.D.

Nominal
Size
mm / in
350
14
400
16
450
18
500
20
600
24

82
Copyright 2011 Shurjoint

Pipe
O. D.
A
B
mm / in
mm / in
mm / in
355.6
368
329
14.000
14.49
12.96
406.4
410
359
16.000
16.14
14.13
457.2
461
417
18.000
18.15
16.42
508.0
509
460
20.000
20.04
18.11
609.6
610
562
24.000
24.00
22.13

Connect with the Best!

Size: 14"~24"

Dimensions
C
D
E
mm / in
mm / in
mm / in
184
283
154
7-1/4
11.14
6.06
191
310
173
7-1/2
12.20
6.81
203
364
203
8
14.33
8.00
219
408
226
8-5/8
16.06
8.80
222
457
249
8-3/4
18.00
9.80

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
46.0
101.2
54.0
118.8
77.0
169.4
96.0
211.2
131.0
288.2

Catalog 2011

MODEL

SJ-930 Horizontal Swing Check Valve


Shurjoint Model SJ-930 horizontal swing

coupling. The 316 stainless steel clapper is

check valves are supplied with grooved

supplied standard encapsulated with Nitrile.

ends and are designed for general services

As an option we offer Fluoroelastomer

including mining and oilfield applications.

(Viton) or Teflon encapsulations to meet

The SJ-930 features a bonnet cap which

your service requirements.

is drilled, tapped (1/2" NPT), and plugged


and secured using a Shurjoint XH-1000

Pressure-Temperature Rating

Size

in / mm

Nom.
Rating

Working
Pressure

Shell
Test

2 2

Class 400
50 - 65

1000 psi @100F


70 Bar @38C

1500 psi
105 Bar

3" 4"

Class 300
80 100

600 psi @100F


40 Bar @38C

900 psi
60 Bar

Max. Service
Temperature

Nitrile: 180F / 82C

UP

*Working pressure is based on connection with cut-grooved standard wall carbon steel pipe.
*Seat test: 110% the working pressure.

Nominal
Size
mm / in
60
2
65
2
80
3
100
4

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500

Max Working
Pressure
A
Bar / Psi
mm / in
70
229
1000
9.00
70
235
1000
9.25
40
273
600
10.75
40
305
600
12.00

Dimensions
B
C
mm / in
mm / in
124
150
4.88
5.90
140
178
5.50
7.00
146
188
5.75
7.40
194
222
7.63
8.74

Approx.
Weight
Kgs / Lbs
6.6
14.5
10.4
22.9
12.2
26.8
17.3
38.1

*Pressure ratings are based on cut-grooved sch. 40 or thicker pipe connected with Shurjoint XH-1000 extra heavy rigid couplings.

Viton is a registered trademark of DuPont.

Connect with the Best!

www.shurjoint.com

83
Copyright 2011 Shurjoint

Catalog 2011

MODEL

650N EXPANSION JOINT


The Shurjoint Model 650N Expansion Joint

excess movement and or the accidental pull-

is a slide-type expansion joint which provides

out of the grooved end pieces. The Model

0 to 3" (0 to 76mm) of axial end movement.

650N can also be supplied with plain-ends

The components are supplied epoxy coated

for use with the Model 79 Wildcat plain-end

(RAL3000 red) for ease of use and longer

coupling.

life. An integral safety device prevents


Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Max. Service
Temperature

Class

300 psi @100F

EPDM: 230F / 110C

20 Bar @38C

Nitrile: 180F / 82C

150

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Shell test, 1.5 times the working pressure, is the proof test pressure.
*Burst pressure is engineered minimum 3 times the working pressure.

A
B

L min.
L max.


Nominal

Size

mm / in

50

2

65

2


76.1 mm


80

3

100

4


165.1 mm


150

6

84
Copyright 2011 Shurjoint

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
165.1
6.500
168.3
6.625

Max.
Working Pressure
Bar / PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Connect with the Best!

Max.
Movement
A
mm / in
mm / in
76
96
3
3.78
76
116
3
4.57
76
116
3
4.57
76
146
3
5.76
76
160
3
6.30
76
260
3
10.25
76
260
3
10.25

Dimensions
B
L min.
L max.
mm / in
mm / in
mm / in
144
304
381
5.67
12.00
15.00
168
304
381
6.61
12.00
15.00
168
304
381
6.61
12.00
15.00
198
304
381
7.80
12.00
15.00
250
359
435
9.84
14.13
17.13
334
406
482
13.15
16.00
19.00
334
406
482
13.15
16.00
19.00

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
6.3
13.9
8.7
19.1
8.5
18.7
12.3
27.1
18.4
40.5
41.8
92.0
42.8
94.2

Catalog 2011

MODEL

651 EXPANSION JOINT


The Model 651 Expansion Joint is a

or Model 7707 flexible couplings and cut-

combination of couplings and specially

grooved Sch. 40 pipe nipples. Customized

machined pipe nipples that are joined in a

units are available. The components are

series to accommodate the expansion and

supplied epoxy coated (RAL3000 red) for

or contraction of a piping system. Standard

ease of use and longer life.

units are comprised of either Model 7705


Pressure-Temperature Rating
Nom.
Rating

Working Pressure
(STD, Roll-grooved)

Max. Service
Temperature

Class

300 psi @100F

EPDM: 230F / 110C

150

20 Bar @38C

Nitrile: 180F / 82C

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Shell test, 1.5 times the working pressure, is the proof test pressure.
*Burst pressure is engineered minimum 3 times the working pressure.

L min.

L max.


Nominal

Size

mm / in

40

1

50

2

65

2


76.1 mm


80

3

100

4


133.0 mm



165.1 mm


150

6

200

8

250

10

300

12

Pipe
O. D.
mm / in
48.3
1.900
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
133.0
5.250
165.1
6.500
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750

Connect with the Best!

Max.
Movement
mm / in
58
2.25
58
2.25
58
2.25
58
2.25
58
2.25
45
1.75
45
1.75
45
1.75
45
1.75
45
1.75
45
1.75
45
1.75

L
min.
mm / in
718
28.25
718
28.25
718
28.25
718
28.25
718
28.25
667
26.26
667
26.25
667
26.26
667
26.26
667
26.26
826
32.50
826
32.50

L
Max.
mm / in
776
30.55
776
30.55
776
30.55
776
30.55
776
30.55
712
28.00
712
28.00
712
28.00
712
28.00
769
30.28
870
34.25
870
34.25

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
11.0
24.2
12.2
27.0
16.3
36.0
16.3
36.0
20.9
46.0
16.6
36.5
32.7
72.0
26.4
58.1
41.4
91.1
72.6
159.7
145.3
320.0
169.3
373.0

85
Copyright 2011 Shurjoint

Catalog 2011

MODEL

725F SUCTION DIFFUSER


The Shurjoint Model 725F Suction Diffuser

available to ANSI Class 150, PN 10/16, BS

features a space saving design, ductile iron

10 Table E or JIS 10K.

body and integral vanes that effectively

The Model 725F is supplied with a 304

reduce turbulence and provide optimum flow

stainless steel running strainer and a

conditions at the inlet side of the pump.

disposable fine mesh screen to protect the

The 725F allows for direct connection to

pump during start-up operation.

a flanged end pump. Flange drilling is


Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Max. Service
Temperature

Class

300 psi @100F

EPDM: 230F / 110C

20 Bar @38C

Nitrile: 180F / 82C

150

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Shell test, 1.5 times the working pressure, is the proof test pressure.

C-E
C-T

When ordering, specify the desired


flange drilling.


Nominal Size
Dimensions
Flange

Suction Side
Pump Side
L
C - E
C - T
Drain
Drilling

mm / in
mm / in
mm / in
mm / in
mm / in
in

50

2

80
65
279
162
140


3
2
11.00
6.38
5.50
NPT

80

3

65

2

100
80
330
187
165
1

4
3
13.00
7.38
6.50
NPT

100

4

100

4

150
125
406
229
203
1

6
5
16.00
9.00
8.00
NPT
ANSI Class 150

150


6 PN 10/16

125


5
BS10 Table E

200
150
483
260
229
1
or

8
6
19.00
10.25
9.00
NPT
JIS 10K

200

8

150

6

250
200
584
314
279
1

10
8
23.00
12.38
11.00
NPT

250

10

200

8

300
250
686
394
305
1

12
10
27.00
15.50
12.00
NPT

300

12

86
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
10.5
23.1
12.0
26.4
13.0
28.6
14.0
30.8
15.0
33.0
16.0
35.2
30.0
66.0
30.0
66.0
31.0
68.2
45.0
99.0
47.0
103.4
52.0
114.4
65.0
143.0
68.0
149.6
70.0
154.0
110.0
242.0
115.0
253.0
126.0
277.2

Catalog 2011

MODEL

725F SUCTION DIFFUSER - FABRICATED


Shurjoint Model 725F Suction Diffusers
in sizes 14 to 24 (350 to 600mm) are
fabricated from carbon steel pipe materials.
Flange drilling is available to ANSI Class
150, PN 10/16, BS 10 Table E or JIS 10K.

C-E

Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Max. Service
Temperature

Class

300 psi @100F

EPDM: 230F / 110C

20 Bar @38C

Nitrile: 180F / 82C

150

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Shell test, 1.5 times the working pressure, is the proof test pressure.


Nominal Size

Suction Side
Pump Side
L

mm / in
mm / in
mm / in

250
889

10
35.00

350
300
889

14
12
35.00

350
965

14
38.00

300
965

12
38.00

400
350
965

16
14
38.00

400
1067

16
42.00

350
1067

14
42.00

450
400
1067

18
16
42.00

450
1270

18
50.00

400
1270

16
50.00

500
450
1270

20
18
50.00

500
1346

20
53.00

450
1372

18
54.00

600
500
1372

24
20
54.00

550
1600

22
63.00

Connect with the Best!

C-T

Model 725F
When ordering, specify the desired
flange drilling.

Dimensions
Flange
C - E
C - T
Drain

Drilling
mm/in
mm/in
in
610
356
24.00
14.00
162
356

6.38
14.00
NPT
660
406
26.00
16.00
660
419
26.00
16.50
660
419
1
26.00
16.50
NPT
724
445
28.50
17.50
ANSI Class 150
724
445

28.50
17.50
PN 10/16
724
445
1

28.50
17.50
NPT
BS10 Table E
889
508
or
35.00
20.00
JIS 10K
889
508
35.00
20.00
889
508
1
35.00
20.00
NPT
927
597
36.50
23.50
940
521
37.00
20.50
940
521
1
37.00
20.50
NPT
1105
606
43.50
23.88

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
191
420
202
444
242
532
232
510
242
532
312
686
306
673
312
686
406
893
392
862
406
893
543
1195
553
1217
571
1256
679
1494

87
Copyright 2011 Shurjoint

Catalog 2011

MODEL

726 Y-STRAINER
The Shurjoint Model 726 Grooved-end

maintenance and is suitable for either vertical

Y-Strainers are designed to strain foreign

or horizontal installation.

matter and debris from piping systems

Standard Screen: 1/16 (1.6mm) perforated

and provide inexpensive protection for

for 2 3 sizes and 1/8 (3.2mm) perforated

costly pumps, meters and other pipeline

for 4 16. Other customized screen

components. The Model 726 features a low

perforations are also available upon request.

pressure drop, fast installation, easy


C

Pressure-Temperature Rating

Size

in / mm

Nom.
Rating

Working
Pressure

Max. Service
Temperature

2 6

Class 150
50 - 150

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C

8" 30"

Class 125
200 750

175 psi @100F


12 Bar @38C

88
Copyright 2011 Shurjoint

Pipe
OD
mm / in
60.3
2.375
73.0
2.875
76.1
3.000
88.9
3.500
114.3
4.500
139.7
5.500
141.3
5.563
168.3
6.625
165.1
6.500
216.3
8.516
219.1
8.625
267.4
10.528
273.0
10.750
318.5
12.539
323.9
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
558.8
22.000
609.6
24.000
660.4
26.000
711.2
28.000
762.0
30.000

Max. Working
Pressure
A
bar / psi
mm / in
20
248
300
9.75
20
273
300
10.75
20
273
300
10.75
20
299
300
11.75
20
362
300
14.25
20
419
300
16.50
20
419
300
16.50
20
470
300
18.50
20
470
300
18.50
16
610
232
24.00
16
610
232
24.00
12
686
175
27.00
12
686
175
27.00
12
762
175
30.00
12
762
175
30.00
12
1016
175
40.00
12
1067
175
42.00
12
1232
175
48.50
12
1365
175
53.75
12
1524
175
60.00
12
1626
175
64.00
12
1727
175
68.00
12
1829
175
72.00
12
1905
175
75.00

Connect with the Best!

B
A
A

Nitrile: 180F / 82C

*Working pressure is based on connection with roll- or cut-grooved standard wall


carbon steel pipe.
*Shell test, 1.5 times the working pressure, is the proof test pressure.


Nominal

Size

mm / in

50

2

65

2


76.1mm


80

3

100

4


139.7mm


125

5

150

6


165.1mm



200 JIS


200

8


250 JIS


250

10


300 JIS


300

12

350

14

400

16

450

18

500

20

550

22

600

24

650

26

700

28

750

30

2"-12"

18"-30"
Fabricated

14"-16"

Dimensions
B
C
mm / in
mm / in
181
116
7.13
4.56
199
122
7.83
4.80
199
122
7.83
4.80
221
129
8.70
5.08
269
168
10.59
6.61
330
258
13.00
10.16
330
258
13.00
10.16
357
219
14.05
8.62
357
219
14.05
8.62
454
284
17.87
11.18
454
284
17.87
11.18
522
320
20.55
12.60
522
320
20.55
12.60
609
366
24.00
14.40
609
366
24.00
14.40
760
480
29.92
18.90
777
483
30.60
19.00
851
711
33.50
28.00
991
813
39.00
32.00
1029
838
40.50
33.00
1067
864
42.00
34.00
1194
965
47.00
38.00
1308
1041
51.50
41.00
1422
1130
56.00
4450

Drain Plug
Size
mm / in
15

15

15

15

25
1
25
1
25
1
25
1
25
1
40
1
40
1
40
1
40
1
40
1
40
1
32
1
32
1
50
2
50
2
50
2
50
2
50
2
50
2
50
2

www.shurjoint.com

Approx.
Weight
Kgs / Lb
4.2
9.3
6.0
13.2
6.0
13.2
7.6
16.8
12.0
26.4
22.0
48.4
22.0
48.4
29.7
65.4
29.5
65.0
55.0
121.0
55.0
121.0
83.0
182.6
83.0
182.6
126.0
277.2
126.0
277.2
246.5
543.4
322.0
709.9
375.0
825.0
480.0
1056.0
670.0
1474.0
765.0
1683.0
1020.0
2244.0
1370.0
3014.0
1585.0
3487.0

Catalog 2011

MODEL

728 T-STRAINER
Shurjoint Model 728 Grooved-end

pressure drop, fast installation, easy

T-Strainers are designed to strain foreign

maintenance and is suitable for either vertical

matter and debris from piping systems

or horizontal installation.

and provide inexpensive protection for

Standard Screen: Mesh 12 for 2 3 sizes

costly pumps, meters and other pipeline

and mesh 6 for 4 14.

components. The Model 726 features a low

Pressure-Temperature Rating
Nom.
Rating

Working
Pressure

Max. Service
Temperature

Class

300 psi @100F

EPDM: 230F / 110C

20 Bar @38C

Nitrile: 180F / 82C

150

Plug, H
C

*Working pressure is based on connection with roll- or cut-grooved


standard wall carbon steel pipe.
*Shell test, 1.5 times the working pressure, is the proof test pressure.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14

Pipe
O. D.
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750
355.6
14.000

Max. Working
Pressure
A
Bar / psi
mm / in
20
166
300
6.54
20
191
300
7.50
20
216
300
8.50
20
254
300
10.00
20
279
300
11.00
20
330
300
13.00
20
394
300
15.50
20
457
300
18.00
20
508
300
20.00
20
559
300
22.00

Dimensions
B
C
mm / in
mm / in
120
125
4.72
4.92
132
142
5.19
5.59
146
164
5.74
6.45
165
190
6.49
7.48
190
218
7.48
8.58
212
260
8.34
10.23
253
320
9.96
12.60
284
380
11.18
14.96
309
430
12.16
16.92
451
540
17.75
21.25

H
(Drain Plug)
mm / in
15

15

15

25
1
25
1
25
1
40
1
40
1
40
1
40
1

Approx.
Weight
Kgs / Lbs
3.0
6.6
4.0
8.8
6.0
13.2
8.0
17.7
13.0
28.6
20.0
44.0
35.0
77.0
52.0
114.6
72.7
160.25
84.5
186.29

The T-strainer shall be cleaned periodically


or before the differential pressure reaches
10 psi.

Connect with the Best!

www.shurjoint.com

89
Copyright 2011 Shurjoint

Catalog 2011

MODEL

RCV RISER CHECK VALVE


The Model RCV is a grooved-end ductile

and the streamlined body provides for low

iron body check valve, designed for use

friction loss. The valve can be installed in

in the risers of wet type fire protection

the vertical or horizontal position. Valves are

systems. The single clapper design features

tested to UL312.

dual springs for non-slamming operation

Pressure-Temperature Rating
Nom.

Rating

Nom.
Size

Working
Pressure

Max. Service
Temperature



CWP

2 6
65 - 150

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on connection with roll- or cut-grooved standard


wall carbon steel pipe.

NPT or BSP

Nominal

Size

mm / in

65

2


76.1 mm


80

3

100

4


139.7 mm


125

5


165.1 mm


150

6

90
Copyright 2011 Shurjoint

Pipe
O. D.
A
mm / in
mm / in
73.0
190
2.875
7.48
76.1
190
3.000
7.48
88.9
178
3.500
7.00
114.3
216
4.500
8.50
139.7
330
5.500
13.00
141.3
330
5.563
13.00
165.1
305
6.500
12.00
168.3
305
6.625
12.00

Connect with the Best!

Dimensions
B
Drain NPT or BSP
mm / in
in
114

1
4.50
114

1
4.50
114

1
4.50
146

2
5.75
210

2
8.25
210

2
8.25
210

2
8.25
210

2
8.25

www.shurjoint.com

Weight
Kgs / Lbs
4.98
10.96
4.98
10.96
4.99
10.98
8.49
18.68
23.34
51.35
23.80
52.36
22.83
50.23
23.10
50.82

Section 5
Threaded Fittings
& Welding Outlets
Threaded Fittings & Welding Outlets......................................... 92
Threaded Fittings
811 / 812 / 813 / 814 / 815 Elbows, Tees....................................... 93
815 / 816 / 817 / 818 Tee, Cross, Coupling..................................... 94
819 / 820 / 825 / 827 / 831 / 832 Plug, Cap Extension Piece,
Hex Bushing, Elbow, Tee...................................................................... 95

830 / 841 Union, Companion Flange................................................. 96


Top Beam Clamp
B20 / B24 Beam Clamps................................................................... 96
Welding Outlets
71 Threaded Outlet.............................................................................. 97
72C / 72R Welding Outlet.................................................................. 98

Catalog 2011

Catalog 2011

Threaded Fittings
& Welding Outlets
Shurjoint offers a complete range
of ductile iron Class 300 threaded
fittings in sizes from to 2.
Shurjoint ductile iron threaded
fittings are 100% air tested
underwater to ensure leak-free
performance. The Shurjoint ductile
iron fitting series is UL listed and
FM approved, making them the
right choice for fire protection and
other general application services.

Welding Outlets

Pressure-Temperature Rating (ANSI


B16.3 & B16.14)
Nom.
Rating

branch outlet at any desired location along


the header pipe. Available in a variety of

1 : 2000 psi / 140 Bar

Class 300 1 2 : 1500 psi / 105 Bar


Shurjoint welding outlets provide an easy

Working Pressure (W.O.G.) Working Pressure


@150F / @65C
Saturated Steam
300 psi (20 Bar)

size and configurations including threaded,

2: 1000 psi / 70 Bar

cut grooved and roll grooved ends. Welding

*Proof test pressure: 1.5 times the working pressure, non-shock


cold water.

outlets are UL listed and FM approved for


fire protection applications.

Pressure-Temperature Rating
Unions, Brass to Iron Seat (ANSI B16.39)

Nom.

Rating
Class 300

Working Pressure (W.O.G.) Working Pressure


@150F / @65C

Saturated Steam

600 psi / 42 Bar

300 psi (20 Bar)

*Proof test pressure: 1.5 times the working pressure, non-shock


cold water.
*Max. Temperature: 450F (ASME Boiler Code)

Pressure-Temperature Rating
Companion Flanges (ANSI B16.42)

Nom.

Rating
Class 150

Pressure-Temperature Rating

Working Pressure (W.O.G.) Working Pressure


@150F / @65C

Saturated Steam

250 psi / 17 Bar

150 psi (10 Bar)

Nom.

Rating

Working Pressure (W.O.G.) Working Pressure

Class 300

*Proof test pressure: 1.5 times the working pressure, non-shock


cold water.

@150F / @65C

Saturated Steam

600 psi / 42 Bar

300 psi (20 Bar)

*Proof test pressure: 1.5 times the working pressure, non-shock


cold water.
*Burst test pressure: Minimum 3 times the working pressure.

Material: Ductile iron ASTM A536 Gr. 65-45-12


Dimensions: ANSI B16.3 Class 150 except
bushings and plugs (B16.14), unions
(B16.39) and companion flanges (B16.42)
Ductile Iron Class 300 threaded fittings are
designed to the same dimensions as that
of Class 150 malleable iron fittings. Though
due to the superior strength characteristics,

Threads: ANSI B1.20.1 NPT or ISO-7


(BSPT)
Finish: Black or electro-zinc plated

ductile Iron fittings carry a much higher


pressure rating. Laboratory tests confirm
Shurjoint ductile iron fittings have passed
hydrostatic test pressures exceeding 6,000
psi / 414 Bar, which is equal to four times
the 1,500 psi /103 Bar as specified by ANSI
B16.3 for 1-1/2 2 sizes.

General Dimensions

These dimensions apply to all


standard fittings, both straight
and reducing. For center-to-face
dimensions(*), see fitting tables.

E
B

Pipe
H
E
Size
Band O.D. Band Width

in
in
in

1.02

0.25

0.43

1.46

0.27

0.50

1.77

0.30

0.58

2.15

0.34

0.67

2.43

0.37

0.70

2.96

0.42

0.75

3.59

0.48

0.92

Burst pressure testing of DI threaded fittings (2")

92
Copyright 2011 Shurjoint

Connect with the Best!

B
Thread Length
(min.)
in

www.shurjoint.com

MODEL

Catalog 2011

MODEL

811 90 Elbow

814 TEE

A
A
A
A








Nominal Size
in


1
1
1
2
2

A
in
1.12
1.31
1.50
1.75
1.94
2.25
2.70

Weight
Lbs
0.25
0.35
0.57
0.97
1.17
1.83
3.34

Box Q'ty
Pcs
240
120
70
40
30
20
10

Nominal Size
in


1
1
1
2
2

A
A
in
1.12
1.31
1.50
1.75
1.94
2.25
2.70

Weight
Lbs
0.31
0.48
0.81
1.28
1.72
2.57
4.44

Box Q'ty
Pcs
150
90
60
35
24
12
8

MODEL

812 REDUCING 90 ELBOW

MODEL

815 REDUCING TEE

B
C
A

Nominal Size

in

x

1 x

1 x

1 x

1 x

1 x 1

1 x

1 x

1 x 1

1 x 1

2 x

2 x 1

2 x 1

2 x 2

A
in
1.20
1.26
1.18
1.34
1.45
1.58
1.41
1.52
1.65
1.82
1.60
1.73
2.02
2.39

B
in
1.22
1.36
1.45
1.53
1.62
1.67
1.66
1.75
1.80
1.88
1.97
2.02
2.16
2.60

Weight
Lbs
0.35
0.46
0.51
0.64
0.68
0.81
0.84
0.90
0.95
1.10
1.19
1.47
1.61
2.93

Box Q'ty
Pcs
160
110
90
75
60
55
45
45
40
35
30
25
20
15

MODEL

813 45 Elbow
A

Nominal Size
in


1
1
1
2
2

A
in
0.88
0.98
1.12
1.29
1.43
1.68
1.95

Weight
Lbs
0.22
0.33
0.55
0.84
0.92
1.63
2.42

Connect with the Best!

Box Q'ty
Pcs
250
150
90
50
35
18
12

A

Nominal Size

in






1



1



1



1







1

1

1
1



1


1





1

1

1



1
1


1





1

1

1

1
2

1
2





1
1


1
2

2





2
1

1

1

2
2

B
A
in
1.20
1.50
1.26
1.37
1.50
1.26
1.37
1.34
1.45
1.58
1.75
1.34
1.45
1.58
1.44
1.50
1.65
1.94
1.41
1.52
1.65
1.41
1.52
1.65
1.82
2.25
2.25
1.49
1.60
1.73
2.02
2.25
1.49
1.60
1.73
1.90
2.02
1.74

B
in
1.20
1.36
1.20
1.31
1.45
1.26
1.37
1.26
1.37
1.50
1.67
1.34
1.45
1.58
1.31
1.37
1.50
1.80
1.34
1.45
1.58
1.41
1.52
1.65
1.82
2.02
2.10
1.41
1.52
1.65
1.94
2.16
1.49
1.60
1.73
1.90
2.02
1.60

www.shurjoint.com

C
in
1.22
1.50
1.36
1.45
1.50
1.36
1.45
1.53
1.62
1.67
1.75
1.53
1.62
1.67
1.69
1.75
1.80
1.94
1.66
1.75
1.80
1.66
1.75
1.80
1.88
2.25
2.25
1.88
1.97
2.02
2.16
2.25
1.88
1.97
2.02
2.10
2.16
2.32

Weight
Lbs
0.46
0.71
0.59
0.66
0.77
0.64
0.75
0.79
0.88
1.01
1.25
0.84
0.99
1.12
0.92
1.01
1.19
1.54
1.08
1.14
1.39
1.10
1.17
1.36
1.56
2.13
2.22
1.52
1.47
1.63
2.09
2.33
1.56
1.61
1.80
2.09
2.24
2.35

Box
Pcs
95
55
80
65
55
65
60
50
50
45
40
45
45
40
40
40
30
30
40
40
30
35
35
30
30
15
15
30
25
20
20
15
20
20
20
20
15
15

93
Copyright 2011 Shurjoint

MODEL

MODEL

815 BULLHEAD TEE

817 CROSS / REDUCING CROSS


B

B
C

Catalog 2011

A
A
A

Model 817 Cross



Nominal Size

in



1


1
1
1

1

1
1

1

1
1

2


1
2
1

1
2

2
2
2

A
in
1.45
1.67
1.80
1.88
1.88
2.10
2.16
2.16
2.60

B
in
1.45
1.67
1.80
1.80
1.88
2.10
2.10
2.16
2.60

C
in
1.37
1.58
1.65
1.82
1.82
1.90
2.02
2.02
2.39

Weight
Lbs
0.66
0.97
1.15
1.43
1.52
1.80
1.94
2.00
3.61

Box Q'ty
Pcs
65
45
35
30
30
24
20
20
10

Nominal Size

(NPT) in





1

1

1

2

A
in
1.12
1.31
1.50
1.75
1.94
2.25

B
in
1.12
1.31
1.50
1.75
1.94
2.25

Weight
Lbs
0.48
0.77
0.95
1.43
1.87
2.86

Box Q'ty
Pcs
90
60
45
25
20
10

Weight
Lbs
1.25
1.47
1.94

Box Q'ty
Pcs
30
24
16

Weight
Lbs
0.18
0.26
0.42
0.57
0.77
1.17
2.11

Box Q'ty
Pcs
360
200
110
75
60
30
18

MODEL

816 REDUCING COUPLING

Model 817 Reducing Cross


Nominal Size

(NPT) in
1x1x1x1
1x1x1x1
2 x 2 x 1 x 1

Nominal Size

in

x

1 x

1 x

1 x

1 x 1

1 x 1

1 x 1

2 x 1

2 x 1

2 x 1

2 x 2

A
in
1.63
1.69
1.37
2.06
2.06
2.31
2.31
2.81
2.81
2.81
3.25

Wrench Size
in
1
1
1
1
---
---
---
---
---
---
---

Weight
Lbs
0.37
0.37
0.48
0.59
0.66
0.84
0.92
1.23
1.28
1.36
2.24

Box Q'ty
Pcs
150
140
120
80
60
50
45
35
30
30
18

Copyright 2011 Shurjoint

Connect with the Best!

B
in
1.58
1.65
1.73

MODEL

818 STRAIGHT COUPLING

Nominal Size

(NPT) in





1

1

1

2

2

94

A
in
1.67
1.80
2.02

A
in
1.38
1.61
1.77
2.00
2.20
2.60
3.00

Wrench Size
in
1
1
111/16
2
2
2
3

www.shurjoint.com

MODEL

Catalog 2011

MODEL

819 PLUG

827 HEX BUSHING


A

Nominal Size (NPT)



in





1

1

1

2

A
in
0.93
1.13
1.25
1.36
1.45
1.50

Weight
Lbs
0.09
0.18
0.25
0.42
0.59
0.95

Box Q'ty
Pcs
500
300
200
110
80
45

Nominal Size
in
1 x
1 x
1 x 1
1 x 1
1 x 1
2 x 1
2 x 1
2 x 1

A
in
1.06
1.06
1.18
1.26
1.26
1.34
1.34
1.34

Weight
Lbs
0.20
0.18
0.29
0.53
0.37
0.75
0.75
0.64

Box Q'ty
Pcs
280
280
150
100
100
80
80
80

MODEL

MODEL

831 LONG STREET 90 ELBOW

820 CAP
A

A
B
Nominal Size (NPT)

in





1

1

1

2

2

A
in
0.89
1.00
1.18
1.32
1.38
1.48
1.77

Weight
Lbs
0.14
0.20
0.33
0.46
0.57
0.88
1.54

Box Q'ty
Pcs
500
300
180
110
80
45
25

MODEL

Nominal Size

in

1 x M

1 x 1M

A
in
1.50
1.50

B
in
3.00
3.00

Weight
Lbs
0.66
0.81

Box Q'ty
Pcs
80
60

MODEL

825 EXTENSION PIECE

832 LONG STREET TEE


C

Nominal Size
in
x 1L
x 2L
x 1L
x 2L

A
A
in
1.50
2.00
1.50
2.00

Weight
Lbs
0.18
0.22
0.22
0.26

Connect with the Best!

Box Q'ty
Pcs
300
250
250
200

Nominal Size

in
1 x x1M
1 x 1 x 1M

B
A
in
1.50
1.50

B
in
1.40
1.50

C
in
3.00
3.00

www.shurjoint.com

Weight
Lbs
0.91
1.03

Box Qty
Pcs
50
45

95
Copyright 2011 Shurjoint

MODEL

Catalog 2011

MODEL

830 BRASS SEAT UNION

841 COMPANION FLANGE

The Model 841 is a traditional companion flange used for transition


from a flanged to a threaded piping system.

B D
E
A

Nominal Size
in


1
1
1
2

A
in
1.81
1.99
2.17
2.52
2.64
3.15

Weight
Lbs
0.46
0.64
1.01
1.45
1.85
2.86

Box Q'ty
pcs
110
80
50
35
25
18

Nominal Size

in

1

1

1

2

2

3

4

6

8

A
in
4.25
4.62
5.00
6.00
7.00
7.50
9.00
11.00
13.50

B
in
0.56
0.62
0.69
0.75
0.88
0.94
0.94
1.00
1.12

C
in
1.94
2.31
2.56
3.06
3.56
4.25
5.31
7.56
9.69

D
in
0.69
0.81
0.88
1.00
1.12
1.19
1.31
1.56
1.75

E
in
3.12
3.50
3.88
4.75
5.50
6.00
7.50
9.50
11.75

Weight
pcs
1.54
1.94
2.29
4.18
5.83
6.60
11.75
16.50
25.98

MODEL

B20 STANDARD TOP BEAM CLAMP


B24 WIDE MOUTH TOP BEAM CLAMP
Size Range: 3/8 and 1/2 rod.

Material: Ductile iron casting with a

Conforms to: Federal Specification


WW-H-171 (Type 23), Manufacturers

hardened steel cup-point set screw and lock

Standardization Society ANSI/ MSS-SP-58

nut.

(Type 19 & 23), install in accordance with

Application: Designed for structural

ANSI/ MSS-SP-69. Exceeds requirements

attachment to the top of metal beams,

of NFPA-13.

channel or other structural shapes to support

Finish: Black or electro zinc plated.

hanger rod. The universal design allows


clamps to be installed in the top or bottom
beam position.

D
E

B20


Model

No.



B20-3



B20-4



B24-3



B24-4

96
Copyright 2011 Shurjoint

Rod Size
A
B
mm / in
mm / in
M10
19.1

3/4
M12
19.1

3/4
M10
28.6

1-1/8
M12
28.6

1-1/8

Dimensions
C
D
E
mm / in
mm / in
mm / in
12.5
25.4
9.5
0.49
1
3/8
12.5
25.4
9.5
0.49
1
3/8
12.5
25.4
11.1
0.49
1
7/16
12.5
25.4
11.1
0.49
1
7/16

Connect with the Best!

B24
Pipe
Size
mm / in
20 - 100
4
125, 150, 200
5, 6, 8
20 - 100
4
125, 150, 200
5, 6, 8

Max. Recom. Load


Top
Bottom
Kgs / Lbs
Kgs / Lbs
227
114
500
250
432
340
950
750
227
114
500
250
432
340
950
750

www.shurjoint.com

Weight Per
100 pcs
Kgs / Lbs
16.8
37.0
16.0
35.2
19.7
43.3
20.9
46.0

Catalog 2011

MODEL

71 FEMALE THREADED

Outlet
Size

mm / in

OUTLET FITTING

Model 71 Female Threaded Outlet Fittings


are designed to provide a threaded outlet

15

at any desired location along the header.


Made of highly weldable SAE-J403 forged
steel the Model 71 is designed for single

20

pass welding. The Model 71 features a


counter bore and a 1.6mm land around the
full circumference of the mouth, which helps

25
1

ensure full penetration welds and minimize


the likelihood of any burn through or
distortion that might be caused by excessive

32
1

heat. The Model 71 is UL / cUL listed and


FM approved for services up to 300 psi (20
bar).

40
1

A
M

50
2

D
(Hole dia.)
65
2
(73.0 OD)

A
A

80
3

B
M

45

100
4

1/4" x Flat

Header
Size
Range
in

Outlet
OD
A
mm / in

Outlet
Length
B
mm / in

Counter-
bore
C
mm / in

Make- Hole Saw Max. Hole


Up
Dia. (Ref.) Dia. (Ref.)
M
D
D
mm / in
mm / in
mm / in


19.1
31.8
10.7
20.5
9.5
1 - 8

0.75
1.25
0.42
0.81

1 1
1 - 2
28.6
25.4
20.6
12.7
17.5
11/16
2 2
1.13
1.00
0.81
0.50
2 8
1 1
34.9
25.4
26.9
12.7
22.2
1 - 2
1.37
1.00
1.06
0.50

2 2
2 8
1 1
1 - 2
40.0
28.6
31.8
12.7
28.6
2 2
1.57
1.13
1.25
0.50
1
2 3

34
58
1 - 2
2 2

48.5
31.8
41.0
12.7
34.9
2 - 3

1.91
1.25
1.61
0.50
1

3-4
5-8

2

55.0
31.8
47.0
22.2
41.3
2

2.16
1.25
1.85
0.88
1
3-4
58
2
3

67.0
38.1
58.6
22.2
54.0
4

2.64
1.50
2.30
0.88
2
5

6
8

3
4

79.0
44.5
70.1
28.6
63.5
5

3.11
1.76
2.76
1.13
2

6
8

4

98.0
53.3
87.0
38.1
79.4
5

3.86
2.10
3.43
1.50
3
6
8

5
125.2
60.3
113.3
50.8
104.8
6

4.93
2.37
4.46
2.00
4
8

10.3
13/32
20.6
13/16

25.4
1

31.8
1

38.1
1

44.5
1

57.2
2

66.7
2

82.6
3
108.0
4

Approx.
Weight
Kgs










































Lbs

0.04

0.09

0.07
0.07
0.06
0.05
0.10
0.09
0.09
0.08
0.11
0.11
0.11
0.11
0.11
0.10
0.19
0.19
0.19
0.18
0.18
0.24
0.24
0.22
0.22
0.40
0.39
0.39
0.39
0.38
0.38
0.48
0.38
0.38
0.45
0.49
0.80
0.77
0.77
0.77
1.40
1.32
1.32

0.15
0.15
0.13
0.11
0.22
0.20
0.20
0.18
0.24
0.24
0.24
0.24
0.24
0.22
0.42
0.42
0.42
0.40
0.40
0.53
0.53
0.48
0.48
0.88
0.86
0.86
0.86
0.84
0.84
1.06
0.84
0.84
0.99
1.08
1.76
1.70
1.70
1.70
3.08
2.90
2.90

The precision machined mouth is designed to fit the first listed header size perfectly, and allows only a small gap along the longitudinal
centerline of the second listed header size.

Each outlet size shown in the following

the header pipe, which is one size smaller

table fits the same header pipe size. Special

than the regular hole size.

attention is required to the hole size (D) in

Outlet
Size

mm / in

M
D
(Hole dia.)

Connect with the Best!

32
1
40
1
50
2
65
2
(73.0 OD)
80
3
100
4

Header
Size
Range
in
1
1
2
2
3
4

Outlet
OD
A
mm / in

Outlet
Length
B
mm / in

Counter-
bore
C
mm / in

Make-
Up
M
mm / in

Hole Saw Max. Hole


Dia. (Ref.) Dia. (Ref.)
D
D
mm / in
mm / in

48.5
1.91
55.0
2.06
67.0
2.64

31.8
1.25
31.8
1.25
38.1
1.50

36.5
1.44
42.5
1.67
54.5
2.15

12.7
0.50
22.2
0.88
22.2
0.88

31.8
1
38.1
1
50.8
2

34.9
1
41.3
1
54.0
2

79.0
3.11

44.5
1.75

65.2
2.57

28.6
1.13

60.3
2

63.5
2

98.0
3.86
125.2
4.93

53.3
2.10
63.3
2.37

81.0
3.19
107.0
4.21

38.1
1.50
50.8
2.00

76.1
3
101.6
4

79.4
3
104.8
4

www.shurjoint.com

Approx.
Weight
Kgs

Lbs

0.19

0.42

0.21

0.46

0.34

0.75

0.49

1.08

0.80

1.76

1.40

3.08

97
Copyright 2011 Shurjoint

Catalog 2011

MODEL

72C CUT GROOVED


WELDING OUTLET

Model 72C Cut Grooved Outlet Fittings are

Outlet
Size
mm/in

50
2

designed to provide a cut grooved outlet at


any desired location along the header. Made
of standard wall (sch.40) pipe, the Model
72C is recommended for use with Sch. 40

65
2

header pipes. The weld end is provided with


a 1.6mm land around the full circumference
to assure a one-pass full penetration weld.
The 72C fittings are recommended for

80
3

services up to 20 bar (300 psi).

100
4
150
6
200
8

Run
Pipe
A
B
in
mm/in
mm/in
2
2
3
4
5
6
8
2
4
5
6
8
3
4
5
6
8
4
5
6
8
6
8
8
10

Dimensions
L
mm/in

W
mm/in

G
mm/in

Approx.
Weight
Kgs/Lbs

60.3
2.375

76.2
3.000

15.88
0.625

7.95
0.312

57.15
2.250

0.40
0.88

73.0
2.875

76.2
3.000

15.88
0.625

7.95
0.312

69.09
2.722

0.50
1.10


88.9
3.500

76.2
3000

15.88
0.625

7.95
0.312

84.94
3.346

0.91
2.00

114.3
4.500

101.6
4.000

15.88
0.625

9.53
0.375

110.08
4.337

1.73
3.80

168.3
6.625
219.1
8.625

101.6
4.000
101.6
4.000

15.88
0.625
19.05
0.750

9.53
0.375
11.13
0.438

163.96
6.460
214.40
8.440

3.18
7.00
4.32
9.50

A
L
G

W
B

451.5
1.6mm land

MODEL

72R ROLL-GROOVED

Outlet
Size
mm/in

32
1

WELDING OUTLET

Model 72R Roll Grooved Outlet Fittings are


designed to provide a roll grooved outlet

40
1

at any desired location along the header.


Made of Sch. 10 pipe, the 72R R-Let is
recommended for use with light wall pipes to
minimize the likelihood of burn-through and

50
2

or distortion of the header pipe. The 72R


fittings are recommended for services up to
20 bar (300 psi).

65
2

76.1mm

A
L
G
WB

100
4

45

98
Copyright 2011 Shurjoint

80
3

Connect with the Best!

Run
Pipe
A
B
in
mm/in
mm/in
1
1
2
2
3
4
5-8
1
2
2
3
4
5-8
2
2
3
4
5
6
8
2
3
4
5
6
8
2
3
4
5
6
8
3
4
5
6
8
4
5
6
8

Dimensions

Approx.

L
mm/in

W
mm/in

G
mm/in

Weight
Kgs/Lbs

42.2
1.660

76.2
3.000

15.88
0.625

7.14
0.281

38.99
1.535

0.15
0.33

48.3
1.900

76.2
3.000

15.88
0.625

7.14
0.281

45.09
1.775

0.18
0.40

60.3
2.375

76.2
3.000

15.88
0.625

8.74
0.344

57.15
2.250

0.29
0.64

73.0
2.875

76.2
3.000

15.88
0.625

8.74
0.344

69.09
27.20

0.51
1.12

76.1
3.000

76.2
3.000

15.88
0.625

8.74
0.344

72.26
2.845

0.51
1.12

88.9
3.500

76.2
3.000

15.88
0.625

8.74
0.344

84.94
3.440

0.56
1.23

114.3
4.500

114.3
4.500

15.88
0.625

8.74
0.344

110.08
4.314

0.94
2.07

www.shurjoint.com

Section 6
Ring Joint, Shouldered and
Plain End Couplings
Ring Joint, Shouldered and Plain End Couplings............................... 100
Ring Joint Couplings

R-88 Ring Joint Coupling.................................................................. 101


R-88 & R-88N 8" ~ 26" Ring Joint Coupling................................... 102
R-88 28" ~ 96" Large Diameter Ring Joint Coupling........................ 103
RH-1000 1000 psi Ring Joint Coupling........................................... 104
RX-3000 3000 psi Ring Joint Coupling............................................ 104
RX-3770 3770 psi Ring Joint Coupling............................................ 105

Ring Joint Fittings

RJ-10 / RJ-11 / RJ-20 / RJ-60 Elbows, Tee & Cap.................... 106


RJ-21 / RJ-50 / RJ-51 / RJ-70 Reducing Tee, Concentric &

Eccentric Reducer, Flange................................................................. 107


Shouldered Couplings........................................................................... 108

S35 Shouldered Flexible Coupling.................................................... 109


SD-28 Shouldered Toggle Coupling................................................. 109

Plain-End Coupling

79 Wildcat Coupling........................................................................110

Catalog 2011

Catalog 2011

Ring Joint, Shouldered and Plain End Couplings


Shurjoint ring joint, shouldered and plain end
couplings are non-grooved mechanical pipe joining
components and excellent alternatives where pipe is
difficult to groove or when grooving is not the preferred
method. The processing of a roll groove on pipe

Ring Joint Coupling

becomes more difficult as the pipe O.D. and or wall


thickness increases. Roll grooving pipe larger than 14
(350 mm) requires proper tools and equipment. Pipe
having a wall thickness greater than .375 (9.5 mm)
may not be practical to roll groove.

Bolts & Nuts

The Shurjoint ring joint

coupling provides a much more secure joint than a comparable


roll-grooved system, simply because the contact area of the rings
is much greater than that of the roll-groove profile. In addition, the

Weld Ring

Housing Segment

welded rings are able to withstand 2 - 3 times the shearing forces of


roll grooves. High pressure couplings up to 3770 psi (260 bar) are
available.
Gasket

Factory Supplied
Weld Rings

Shouldered Coupling

The Shurjoint shouldered

#R-88 Ring Joint Coupling

Housing Segment

Type A Weld-on Ring

piping system is a classic and versatile pipe joining method which

utilizes Type A weld-on rings. Shurjoint shouldered couplings are

Gasket

widely used in irrigation, dewatering on construction sites, and other


installations.
Bolt & Nut

#S35 Shouldered Coupling

Plain-end Coupling

The Shurjoint plain-end

coupling securely grips the pipe with its built-in case hardened

Hardened
Steel Jaws
Gasket

jaws incorporated within heavy duty housing segments and heavy

duty bolts and nuts. The Shurjoint Model 79 Wildcat coupling is


designed to join plain-end or beveled-end carbon steel pipe without
roll-grooving, welding or threading. The Model 79 plain-end coupling
can be used for mining, process piping, manifold piping, and oil field
services.

Housing
Segment
Bolt & Nut

Steel Pipe 2" 16"


(Hardness HB 150 max.)

#79 Plain-end Coupling

100
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

R-88 RING JOINT COUPLING


The Shurjoint Model R-88 Ring Joint

The R-88 Coupling can also be used on

Coupling is an ideal pipe joining method

stainless steel pipe with optional weld rings

when pipe is difficult to groove or when

available in compatible stainless steel

grooving is not the preferred joining method.

grades. Check with Shurjoint for details and

Available in sizes 8 to 96 the R-88 offers

availability.

ease of use and excellent performance.


The Shurjoint Model R-88 Ring Joint

Typical applications
Water & Waste Water Treatment Plants

Coupling is supplied with a pair of factory

Mining & Tunnel Boring

supplied weld rings. For installation weld

Pulp & Paper

a factory-supplied weld ring on each pipe

Hydroelectric Plants

end to be connected, next mount the rubber

Co-Gen Electric Plants

gasket over the pipe ends, place coupling

Food & Beverage

segments over the gasket and fasten the

Compressed Air

bolts and nuts.


The Shurjoint R-88 Ring Joint Coupling
is considered a shoulder coupling with the
factory supplied weld rings serving as the
joint shoulders. The R-88s performance
standards meet and or exceed the
requirements of ASTM F1476 and AWWA
C606. The factory supplied weld rings offer
a much more economical and convenient
alternative to traditional shoulder rings, such
as Type A, B, C, D, E, and G rings.

Max. Internal Service


Pressures of Carbon Steel
Pipe ASTM A53 Gr. B

When designing a piping system you


must select pipe with the appropriate wall
thickness to correspond with the intended
working pressure of the system. The
table lists design working pressure by the
pipe wall schedule, XS, STD and LW, of
representative ASTM A53 Gr. B carbon
steel pipe calculated in accordance with the
formula stipulated in ASME B31.1 Power
Piping 104.1.

P =

Where:

2SE (tm-A)
Do - 2y (tm - A)


P = Maximum internal service pressure (psi)
SE = Allowable stress (psi)
(ASTM A53 Gr. B = 15,000 psi)

tm = Minimum pipe wall thickness (inch)
(87.5% of nominal wall thickness)
Do = Outside diameter of pipe (inch)

y = A coefficient (For ferritic steels 600F
or below = 0.4)

A = Additional thickness (inch) (A = 0)

Max. Internal Service Pressures of Carbon Steel


Pipe ASTM A53 Gr. B
Unit: psi
Nom. Size

in

8

10

12

14

16

18

20

24

26

28

30

32

34

36

38

40

42

44

48

52

54

56

60

XS
0.5"
1586
1262
1058
962
839
744
668
555
512
475
443
415
390
368
349
331
315
301
275
254
245
236
220

STD
0.375"*
1006
913
788
717
625
555
499
415
382
355
331
310
292
275
261
248
236
225
206
190
183
177
165

LW
0.25"/0.312"^
777
621
522
475
415
368
331
275
318
295
275
258
242
229
217
206
187

*8": 0.322", ^ 8 ~ 24: 0.25, 26 ~ 42: 0.312

Connect with the Best!

www.shurjoint.com

101
Copyright 2011 Shurjoint

Catalog 2011

MODEL

R-88 RING JOINT COUPLING


The Shurjoint Model R-88 Ring Joint
Coupling is available in sizes from
8/200mm. Sizes 14/350mm to 24/600mm
are now available either in a two-segment
style (R-88N) or multi-segment style (R-88).
The two-segment style offers a easier and
faster installation.

Pressure-Temperature Rating
Size
Nom. Working Pressure
in / mm Rating
(STD)

Max. Service
Temperature

8 24

Class

400 psi @100F

EPDM: 230F / 110C

200 - 600

250

28 Bar @38C

Nitrile: 180F / 82C

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure for sizes up to 12" (300mm) and 2 times for sizes up to
24" (600mm).

R-88N
Size: 24"

R-88
Size: 12"

A 28" R-88 coupling installed in a chill water system


Max. Working Pressure
Nominal
Pipe Rings both sides fully welded

Size
OD
XS (.500) STD (.375) LW (.312)
A
mm / in
mm / in
Bar / psi
Bar / psi
Bar / psi
mm / in

200
219.1
40
28
28
256

8
8.625
600
400
400
10.08

250
273.0
40
28
28
312

10
10.750
600
400
400
12.29

300
323.9
40
28
28
374

12
12.750
600
400
400
14.72


216.3
40
28
28
253
200JIS

8.516
600
400
400
9.96


267.4
40
28
28
306
250JIS

10.528
600
400
400
12.05


318.5
40
28
28
369
300JIS

12.539
600
400
400
14.53
350 (R-88N)
355.6
40
28
24
411

14
14.000
600
400
350
16.18
400 (R-88N)
406.4
35
28
24
461

16
16.000
500
400
350
18.15
450 (R-88N)
457.2
35
28
24
511

18
18.000
500
400
350
20.12
500(R-88N)
508.0
35
28
20
591

20
20.000
500
400
300
23.25
600 (R-88N)
609.6
35
28
17
702

24
24.000
500
400
250
27.63

O.D.

Copyright 2011 Shurjoint

Connect with the Best!

8" ~ 24"
(R-88 & R-88N)

Dimensions
Bolt Size
B
C
mm / in
mm / in
No.
mm / in
330
79


2
x 4
13.00
3.11
386
83


2
x 4
15.20
3.25
455
86


2
x 6
17.90
3.39
327
79


2
M 20 x 120
12.87
3.11
380
83


2
M 20 x 120
14.96
3.25
450
86


2
M 20 x 120
17.72
3.39
380
98

M22
4
14.96
3.86

422
98

M22
4
16.61
3.86

489
105

M24
4
19.25
4.14
1
665
116

M24
4
26.18
4.56
1
762
123

M22
4
30.0
4.84

Sealing
Surface L
mm / in
23
0.91
23
0.91
26
1.02
23
0.91
23
0.91
26
1.02
26
1.02
26
1.02
30
1.18
30
1.18
30
1.18

Ring
Size R
mm / in
6

6

8
5/16
6

6

8
5/16
8
5/16
8
5/16
12*

12

12

R-88N is a two-segment type coupling.


Dimensions are subject to change without notice. Other sizes are available on request.
*10mm shouldered rings are acceptable.

102

www.shurjoint.com

Separation
E (max)
mm / in
4.8
0.19
4.8
0.19
4.8
0.19
4.8
0.19
4.8
0.19
4.8
0.19
9.5
0.375
9.5
0.375
9.5
0.375
9.5
0.375
9.5
0.375

Weight
Kgs / Lbs
7.6
16.8
10.1
22.2
14.0
30.8
8.0
17.6
10.0
22.0
14.8
32.6
17.4
38.3
18.7
41.1
23.1
50.8
38.2
84.0
49.7
109.3

Catalog 2011

MODEL

R-88 RING JOINT COUPLING


Large diameter

The Shurjoint Model R-88 Ring Joint

segments depending on the size and feature

Coupling is available in sizes 28/700mm

two bolts at each joint segment to ensure a

to 96" / 2400mm. The larger diameter

positive connection.

couplings are comprised of 4 to 8 housing


Pressure-Temperature Rating


Size
Nom. Rating

26 - 36

Class 150
650 - 900
38 96

Class 125
950 - 2400

Working Pressure
(STD)

Max. Service
Temperature

300 psi @100F


20 Bar @38C
175 psi @100F
12 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

O.D.

R-88
Size: 48"

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock cold water.
*Burst pressure is engineered minimum 2 times for the listed working pressure.

A
A

28" ~ 38"

26"

Max. Working Pressure


Nominal
Pipe Rings both sides fully welded

Size
OD
XS (.500) STD (.375) LW (.312)
A
mm / in
mm / in
Bar / psi
Bar / psi
Bar / psi
mm / in

650
660.4
28
20
17
726

26
26.000
400
300
250
28.58

700
711.2
28
20
17
806

28
28.000
400
300
250
31.75

750
762.0
28
20
17
857

30
30.000
400
300
250
33.75

800
812.8
28
20
17
908

32
32.000
400
300
250
35.75

850
863.4
24
20
14
959

34
34.000
350
300
200
37.75

900
914.4
24
20
14
1010

36
36.000
350
300
200
39.75

950
965.2
20
16
12
1060

38
38.000
300
232
175
41.75

1000
1016.0
20
16
12
1135

40
40.000
300
232
175
44.69

1050
1066.8
20
16
12
1186

42
42.000
300
232
175
46.70

1100
1117.6
20
16
12
1236

44
44.000
300
232
175
48.66

1200
1219.2
20
16
---
1338

48
48.000
300
232
---
52.68

1300
1320.8
16
12
---
1555

52
52.000
232
175
---
61.25

1350
1371.6
16
12
---
1660

54
54.000
232
175
---
63.25

1400
1422.4
16
12
---
1660

56
56.000
232
175
---
65.38

1500
1524.0
16
12
---
1762

60
60.000
232
175
---
69.38

1650
1676.4
12
8.6
---
1932

66
66.000
175
125
---
76.00

1700
1727.2
12
8.6
---
1994

68
68.000
175
125
---
78.50

1800
1828.8
10
8.6
---
2095

72
72.000
150
125
---
82.50

2100
2133.6
8.6
7
---
2406

84
84.000
125
100
---
94.75

2400
2438.4
8.6
7
---
2711

96
96.000
125
100
---
106.75

40" ~ 96"
Dimensions
Bolt Size
B
C
mm / in
mm / in
No.
mm / in
815
122

8
x4
32.09
4.80
902
171

12
x4
35.50
6.73
955
171

12
1 x 3
37.60
6.73
1003
171

12
1 x 3
39.50
6.73
1054
171

12
1 x 3
41.50
6.73
1103
171

12
1 x 3
43.50
6.73
1156
171

12
1 x 3
45.50
6.73
1229
198

16
1 x 3
48.39
7.80
1280
198

16
1 x 5
50.39
7.80
1318
198

16
1 x 5
51.89
7.80
1420
198

16
1 x 3
55.91
7.80
1539
198

16
1 x 5
60.60
7.80
1590
198

16
1 x 5
62.60
7.80
1641
198

16
1 x 5
64.60
7.80
1742
198

16
1 x 5
68.60
7.80
1925
216

16
1 x 5
75.79
8.00
1976
216

16
1 x 5
77.79
8.00
2078
216

16
1 x 5
81.81
8.00
2383
216

16
1 x 5
93.81
8.00
2662
216

16
1 x 5
105.79
8.00

Sealing
Surface L
mm / in
30
1.18
50
2.00
50
2.00
50
2.00
50
2.00
50
2.00
50
2.00
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37
60
2.37

Ring
Size R
mm / in
12.7
1/2
12.7
1/2
12.7
1/2
12.7
1/2
12.7
1/2
12.7
1/2
12.7
1/2
15.9
5/8
15.9
5/8
15.9
5/8
15.9
5/8
15.9
5/8
15.9
5/8
15.9
5/8
15.9
5/8
19.1
3/4
19.1
3/4
19.1
3/4
19.1
3/4
19.1
3/4

Separation
E (max)
mm / in
9.5
0.375
12.7
0.50
12.7
0.50
12.7
0.50
12.7
0.50
12.7
0.50
12.7
0.50
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
15.9
0.625
19.1
0.75
19.1
0.75
19.1
0.75
19.1
0.75
19.1
0.75

Weight
Kgs / Lbs
59.0
130.0
101.0
222.2
99.5
218.9
102.2
225.4
115.0
253.0
111.6
246.0
125.0
275.0
141.0
310.2
148.6
326.9
156.0
343.2
211.8
466.7
206.0
453.2
214.6
472.1
222.0
488.2
244.2
537.2
278.4
612.5
357.0
785.4
335.3
737.7
354.7
780.3
374.2
823.2

Dimensions are subject to change without notice. Other sizes are available on request.

Connect with the Best!

www.shurjoint.com

103
Copyright 2011 Shurjoint

Catalog 2011

MODEL

RH-1000 1000 PSI RING JOINT COUPLING


The Shurjoint Model RH-1000 coupling is a

and nuts which provide a fully restrained

high pressure ring joint coupling for use with

joint and a maximum working pressure of

Sch. 40, Sch. 80 and heavier wall carbon

1,000 psi (70 Bar) depending on the pipe

steel pipe.

used.

The coupling is comprised of two ductile iron

Two steel weld rings are factory supplied

heavy-wall housings, rubber gasket (EPDM

with the coupling. Steel rings must always

or Nitrile) and two heat-treated track bolts

be fully welded on both sides.

Pressure-Temperature Rating

Nom.
Rating


Class 400

Working Pressure
(STD)

Max. Service
Temperature

1000 psi @100F


70 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal

Size
mm / in

200

8

250

10

300

12

Pipe
OD
mm / in
219.1
8.625
273.0
10.750
323.9
12.750

Max. Working
Pressure
A
Bar / PSI
mm / in
70
282
1000
11.10
70
340
1000
13.32
70
415
1000
16.33

Pipe O.D.

Dimensionsl
B
mm / in
372
14.65
430
16.93
510
20.07


Bolt / Nut Pipe-end Preparation
C
Size
Deflection
R
L
E (max)
mm / in
No.
in
( )
mm / in
mm / in
mm / in
98

12
25
3.2
2
1" x 140
0 18'
3.86
0.47
1
0.13
108

12
25
3.2
2
1" x 165
0 38'
4.25
0.47
1
0.13
106

12
25
3.2
2
1" x 165
0 32'
4.17
0.47
1
0.13

Weight
Kgs / Lbs
18.1
39.8
26.0
57.2
33.0
72.6

*Bolt & nuts are UNC threaded.

MODEL

RX-3000 3000 PSI RING JOINT COUPLING


The Shurjoint Model RX-3000 coupling is

and nuts which provide a fully restrained

a high pressure ring joint coupling for use

joint and a maximum working pressure up to

with Sch. 80, 120 and heavier wall carbon

3,000 psi (210 Bar) depending on the pipe

steel pipe.

used.

The coupling is comprised of two ductile iron

Two steel weld rings are factory supplied

heavy-wall housings, rubber gasket (EPDM

with the coupling. Steel rings must always

or Nitrile) and four heat-treated track bolts

be fully welded on both sides.

Pressure-Temperature Rating

Nom.
Rating


Class 1500

Working
Pressure

Max. Service
Temperature

3000 psi @100F


210 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on API 5L X65 line pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 2 times the working pressure.

Nominal
Size
mm / in
200
8
250
10
300
12

Pipe
OD
mm / in
219.1
8.625
273.0
10.748
323.9
12.752

Max. Working
Pressure
A
Bar / PSI
mm / in
210
300
3000
11.81
210
380
3000
14.96
210
470
3000
18.5

C
R

Pipe O.D.

Dimensions
Bolt / Nut*
Pipe-end Preparation
B
C
Size
R
L
E
mm / in
mm / in
No.
in
mm / in
mm / in
mm / in
394
148

12
31
3
2
1 x 130
15.51
5.83
0.472
1.22

481
152

16
31
3
4
1 x 165
18.93
5.98
0.63
1.22

572
173

16
31
3
4
1" x 160
22.48
6.81
0.63
1.22

*Bolt & nuts are UNC threaded. @ (12.7mm) and (15.9mm) steel rings are also available upon request.

104
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Weight
Kgs / Lbs
35.87
78.92
52.78
116.36
96.24
212.27

Catalog 2011

MODEL

RX-3770 3770 PSI RING JOINT COUPLING


The Shurjoint Model RX-3770 Ring Joint

iron heavy-wall housing segments, rubber

Coupling is designed to provide a fully

gasket (EPDM) and four heat-treated track

restrained joint for use with extra-strong

bolts and nuts. Two steel weld rings are

carbon steel pipe including API 5L Grade

factory supplied with a coupling. Steel rings

X65 line pipe.

shall always be fully welded on both sides.

The coupling is comprised of two ductile

Pressure-Temperature Rating

Nom.
Rating


Class 2000

Working
Pressure

Max. Service
Temperature

3770 psi @100F


260 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on API 5L X65 line pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 2 times the working pressure.

Dimensions
Bolt / Nut*
Pipe-end Preparation
B
C
Size
R
L
E
mm / in
mm / in
No.
in
mm / in
mm / in
mm / in
321
149

12
31
5
4
" x 165
12.64
5.87
0.472
1.22
0.20
414
175

16
38
5
4
1" x 165
16.30
6.89
0.625
1.50
0.20
505
188

19
38
5
4
1" x 175
19.88
7.40
0.750
1.50
0.20
587
219

22
38
6
4
1" x 175
23.10
8.63
0.875
1.50
0.24

Nominal
Size
mm / in
150
6
200
8
250
10
300
12

Pipe
OD
mm / in
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750

Max. Working
Pressure
A
Bar / PSI
mm / in
260
260
3770
10.24
260
329
3770
12.95
260
404
3770
15.90
260
482
3770
19.0

L
E

Weight
Kgs / Lbs
27.7
61.2
49.9
110.0
79.2
174.5
112.3
247.1

*Bolt & nuts are UNC threaded.

Proof and burst pressure testing

Connect with the Best!

www.shurjoint.com

105
Copyright 2011 Shurjoint

RING JOINT FITTINGS

Catalog 2011

MODEL

RJ-10 90 elbow RJ-11 45 elbow


RJ-20 TEE
RJ-60 CAP
Shurjoint offers a full range of ring joint

or wrought carbon steel.

fittings for use with Model R-88 ring joint

Larger sizes are made of carbon steel

couplings.

standard weight pipe, ASTM A53 Gr. B

8 - 24 (200mm 600mm) Models RJ-10,

or equivalent, or fabricated from wrought

RJ-11 & RJ-60 and sizes 8 16 (200mm

carbon steel of the equivalent properties.

400mm) Model RJ-20 are available either in

Other configurations are also available

cast ductile iron to ASTM A536 Gr. 65-45-12

upon request. Contact Shurjoint for details.

C-E

C-E

C-E

C-E

C-E


Nominal

Size

mm / in

200

8

250

10

300

12


200JIS



250JIS



300JIS


350

14

400

16

450

18

500

20

600

24

650

26

700

28

750

30

800

32

850

34

900

36

1000

40

1050

42

1100

44

1200

48

106
Copyright 2011 Shurjoint


Pipe
OD
mm / in
219.1
8.625
273.0
10.750
323.9
12.750
216.3
8.516
267.4
10.528
318.5
12.539
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000
660.4
26.000
711.2
28.000
76.20
30.000
812.8
32.000
863.4
34.000
914.4
36.000
1016.0
40.000
1066.8
42.000
1117.6
44.000
1219.2
48.000

RJ-10 90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
197
13.0
7.75
28.6
229
25.0
9.00
55.0
254
35.0
10.00
77.0
197
13.0
7.75
28.6
229
25.0
9.00
55.0
254
35.0
10.00
77.0
280
37.0
11.00
81.4
305
45.0
12.00
99.0
394
95.0
15.50
209.0
438
138.0
17.25
203.6
508
220.0
20.00
485.0
991
237.0
39.00
521.0
1067
275.0
42.00
605.0
1143
316.0
45.00
695.0
1219
360.0
48.00
792.0
1295
407.0
51.00
895.0
1372
457.0
54.00
1005.0
1524
564.0
60.00
1241.0
1600
622.0
63.00
1368.0
1676
683.0
66.00
1503.0
1829
814.0
72.00
1790.0

Connect with the Best!

RJ-10

RJ-11 45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
108
9.5
4.25
20.9
121
18.0
4.75
39.6
133
23.0
5.25
50.6
108
9.5
4.25
20.9
121
18.0
4.75
39.6
133
23.0
5.25
50.6
152
24.0
6.00
52.8
184
46.0
7.25
101.2
208
48.0
8.00
105.6
229
50.0
9.00
110.0
280
80.0
11.00
176.0
406
119.0
16.00
262.0
438
138.0
17.25
304.0
480
158.0
18.50
348.0
502
180.0
19.75
396.0
533
204.0
21.00
449.0
565
229.0
22.25
504.0
632
282.0
24.88
620.0
660
311.0
26.00
684.0
696
342.0
27.39
752.0
759
407.0
29.88
895.0

RJ-11

RJ-20

RJ-20 Tee
C - E
Weight
mm / in
Kgs / Lbs
197
21.0
7.75
46.2
229
33.0
9.00
72.6
254
47.0
10.00
103.4
197
21.0
7.75
46.2
229
33.0
9.00
72.6
254
47.0
10.00
103.4
280
54.0
11.00
118.8
305
70.0
12.00
154.0
394
122.0
15.50
268.0
438
153.0
17.25
337.0
508
212.0
20.00
466.0
572
348.0
22.50
766.0
597
392.0
23.50
862.0
635
451.0
25.00
992.0
673
516.0
26.50
1135.0
711
584.0
28.00
1285.0
762
657.0
30.00
1445.0
838
814.0
33.00
1790.0
889
837.0
35.00
1841.0
914
943.0
36.00
2075.0
1016
1131.0
40.00
2488.0

www.shurjoint.com

E-E

RJ-60

RJ-60 Cap
E - E
Weight
mm / in
Kgs / Lbs
76
5.5
3.00
12.1
76
6.0
3.00
13.2
76
8.0
3.00
17.6
76
5.5
3.00
12.1
76
6.0
3.00
13.2
76
8.0
3.00
17.6
102
12.0
4.00
26.4
102
15.0
4.00
33.0
127
21.0
5.00
46.2
152
26.0
6.00
57.2
152
35.0
6.00
77.0
267
50.0
10.50
110.0
267
56.0
10.50
123.0
267
62.0
10.50
136.0
267
113.0
10.50
248.6
267
75.0
10.50
165.0
267
152.0
10.50
334.4
305
102.0
12.00
224.0
305
110.0
12.00
242.0
343
126.0
13.50
277.0
343
143.0
13.50
315.0

RING JOINT FITTINGS

Catalog 2011

MODEL

RJ-21 REDUCING TEE


RJ-50 CONCENTRIC REDUCER

RJ-51 ECCENTRIC REDUCER


C-E

C-E

E-E

E-E

RJ-21

RJ-50

RJ-51

RJ-21 Reducing Tee


C - E
Weight
mm / in
Kgs / Lbs
279
66.0
11.00
145.0
305
78.0
12.00
172.0
305
80.0
12.00
176.0
394
112.0
15.50
246.0
394
115.0
15.50
253.0
394
120.0
15.50
264.0
438
135.0
17.25
297.0
438
138.0
17.25
304.0
438
144.0
17.25
317.0
438
149.0
17.25
328.0
508
180.0
20.00
396.0
508
185.0
20.00
407.0
508
190.0
20.00
418.0
508
197.0
20.00
433.0
508
202.0
20.00
444.0

RJ-50 Conc. Reducer


E - E
Weight
mm / in
Kgs / Lbs
203*
23.0
8.00
51.0
229*
29.0
9.00
64.0
229*
29.0
9.00
64.0
241*
33.0
9.50
72.6
381
36.0
15.00
79.0
381
36.0
15.00
79.0
254*
43.0
10.00
95.0
508
45.0
20.0
99.0
254
46.0
10.00
101.0
508
58.0
20.00
128.0
305*
70.0
12.00
154.0
508
70.0
20.00
154.0
305*
70.0
12.00
154.0
508
70.0
20.00
154.0
305*
71.0
12.00
156.0

RJ-51 Ecc. Reducer


E - E
Weight
mm / in
Kgs / Lbs
203*
23.0
8.00
51.0
229*
29.0
9.00
64.0
229*
29.0
9.00
64.0
241*
35.0
9.50
78.0
381
36.0
15.00
79.0
381
36.0
15.00
79.0
254*
43.0
10.00
95.0
508
45.0
20.0
99.0
254
46.0
10.00
101.0
508
58.0
20.00
128.0
305*
70.0
12.00
154.0
508
70.0
20.00
154.0
305*
70.0
12.00
154.0
508
70.0
20.00
154.0
305*
71.0
12.00
156.0

Nominal
Size
mm / in
350 x 300
14 x 12
400 x 300
16 x12
400 x 350
16 x 14
450 x 300
18 x 12
450 x 350
18 x 14
450 x 400
18 x 16
500 x 300
20 x 12
500 x 350
20 x 14
500 x 400
20 x 16
500 x 450
20 x 18
600 x 300
24 x 12
600 x 350
24 x 14
600 x 400
24 x 16
600 x 450
24 x 18
600 x 500
24 x 20

Pipe
OD
mm / in
355.6 x 323.9
14.000 x 12.750
406.4 x 323.9
16.000 x 12.750
406.4 x 355.6
16.000 x 14.000
457.2 x 323.9
18.000 x 12.750
457.2 x 355.6
18.000 x 14.000
457.2 x 406.4
18.000 x 16.000
508.0 x 323.9
20.000 x 12.750
508.0 x 355.6
20.000 x 14.000
508.0 x 406.4
20.000 x 16.000
508.0 x 457.2
20.000 x 18.000
609.6 x 323.9
24.000 x 12.750
609.6 x 355.6
24.000 x 14.000
609.6 x 406.4
24.000 x 16.000
609.6 x 457.2
24.000 x 18.000
609.6 x 508.0
24.000 x 20.000

Concentric reducers marked (*) are made of ductile iron.

MODEL

RJ-70 FLANGE ADAPTER

E-E
RJ-70

Connect with the Best!

Nominal

Size
mm / in

200

8

250

10

300

12

350

14

400

16

450

18

500

20

600

24

Pipe
O.D.
mm / in
219.1
8.625
273.0
10.750
323.9
12.750
355.6
14.000
406.4
16.000
457.2
18.000
508.0
20.000
609.6
24.000

RJ-70 Flange Adapter


E - E
Weight
mm / in
Kgs / Lbs
152
20.4
6
44.9
203
30.5
8
67.1
203
44.6
8
98.1
203
54.0
8.00
118.8
203
66.8
8.00
147.0
203
65.0
8.00
143.0
203
77.0
8.00
169.4
203
130.4
8.00
286.9

www.shurjoint.com

107
Copyright 2011 Shurjoint

Catalog 2011

Shurjoint Shouldered
Piping System
The Shurjoint shouldered piping system is
a classic and versatile piping method used
for a wide range of applications including
irrigation, dewatering on construction sites,

Type A Weld-on Ring

Housing Segment

and other installations, etc. The shouldered


system features full flow characteristics,
provides speed and ease of installation,

Gasket

and proven reliability. The system provides


for limited expansion and contraction and
accommodates some linear and angular
movement. Each joint is a union.

The Shurjoint shouldered piping system

Bolt & Nut

utilizes Type A weld-on rings, manufactured


from mild steel or material compatible to
pipe end used.

Shoulder Dimensions

utilizes Type A weld-on rings, manufactured

D1

The Shurjoint shouldered piping system


L
3

from mild steel or material compatible to

D2

( Type A Weld-on Rings )

pipe end used. Type A rings are suitable for


services up to maximum 40 bar / 600 psi for
sizes up to 100mm / 4 and 28 bar / 400 psi
for 125mm / 5 through 200mm / 8.

108
Copyright 2011 Shurjoint

Connect with the Best!

Nominal
Size
mm/in
50
2
80
3
100
4
150
6
150
6
200
8

Pipe OD
D1
mm/in
60.3
2.375
88.9
3.500
114.3
4.500
165.1
6.500
168.3
6.625
219.1
8.625

Shoulder Diameter
D2
mm/in
66.5
2.62
97.0
3.82
122.0
4.80
174.5
6.87
178.0
7.00
232.0
9.13

Shoulder Length
L
mm/in
16.0
0.63
16.0
0.63
17.5
0.69
17.5
0.69
17.5
0.69
20.6
0.81

www.shurjoint.com

Nominal Gap
E
mm/in
3.2
0.13
3.2
0.13
3.2
0.13
3.2
0.13
3.2
0.13
3.2
0.13

Catalog 2011

MODEL

S35 Shouldered FLEXIBLE COUPLING


The Shurjoint Model S35 coupling is a

of ductile iron to ASTM A536 Gr. 65-45-12

flexible type shouldered coupling for general

and or A395 Gr. 65-45-15 and are normally

applications for use on Type A shouldered

supplied in hot-dip galvanized. The standard

pipe ends. The housing segments are made

rubber gasket is Grade T Nitrile.

Pressure-Temperature Rating

Nom.
Rating


Class 150

Working Pressure
(STD)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
50
2
80
3
100
4
150
6
150
6
200
8

Pipe
OD
mm / in
60.3
2.375
88.9
3.500
114.3
4.500
165.1
6.500
168.3
6.625
219.1
8.625

Working
Pressure
A
Bar / PSI
mm / in
20
99.0
300
3.90
20
129.0
300
5.08
20
159.0
300
6.26
20
213.0
300
8.39
20
219.0
300
8.62
20
273.0
300
10.75

Dimensions
B
C
mm / in
mm / in
139.0
46.0
5.47
1.81
168.0
46.0
6.61
1.81
200.0
50.0
7.87
1.97
267.0
50.0
10.50
1.97
279.0
50.0
11.00
1.97
335.0
60.0
13.19
2.36

Allowable Pipe
Bolt
End Separation
Deflection
Size
mm / in
( )
in

3.2
" x 2"
2 43'
0.13

3.2
" x 3"
1 53'
0.13

3.2
" x 3"
1 29'
0.13
3.2

" x 3"
1 2'
0.13

3.2
" x 3"
1 1'
0.13

3.2
" x 4"
0 47'
0.13

Weight
Kgs / Lbs
1.1
2.4
1.5
3.9
2.2
4.8
3.5
5.0
3.8
5.3
5.9
7.4

MODEL

SD-28 Shouldered TOGGLE COUPLING


The Shurjoint Model SD-28 coupling is

use of a split pin prevents accidental opening

designed to connect shouldered-end pipe

of the couplings. The housing segments

with Type A rings for services where frequent

are made of ductile iron to ASTM A536 Gr.

assembly and disassembly is desired or

65-45-12 and or A395 Gr. 65-45-15 and are

required. The housing segments are hinged

normally supplied in hot-dip galvanized. The

with a lever handle for easy installation. The

standard rubber gasket is Grade T Nitrile.

Pressure-Temperature Rating

Nom.
Rating


Class 150

Working Pressure
(STD)

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C


Nitrile: 180F / 82C

Split pin

*Working pressure is based on standard wall carbon steel pipe.


*Proof test pressure: 1.5 times the working pressure, non-shock
cold water.
*Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
50
2
80
3
100
4
150
6
150
6
200
8

Pipe
OD
mm / in
60.3
2.375
88.9
3.500
114.3
4.500
165.1
6.500
168.3
6.625
219.1
8.625

Max. Working
Pressure
A
Bar / PSI
mm / in
20
86.5
300
39.32
20
126
300
4.96
20
160
300
6.30
20
214
300
8.43
20
217
300
8.54
20
278
300
10.95

Connect with the Best!

Dimensions
B
C
mm / in
mm / in
112.5
49
4.43
1.93
164
49
6.46
1.93
214
52
8.43
2.05
283
52
11.14
2.05
282
52
11.10
2.05
360
60
14.17
2.36

Allowable Pipe
End Separation (E)
Deflection
mm / in
( )
3.2

2 - 43'
0.125
3.2

1 - 53'
0.125
3.2

1 - 29'
0.125
3.2

1 - 2'
0.125
3.2

1 - 1'
0. 125
3.2

0 - 47'
0.125

www.shurjoint.com

Weight
Kgs / Lbs
1.3
2.8
2.0
4.4
3.0
6.6
4.3
6.5
4.5
9.9
8.3
18.3

109
Copyright 2011 Shurjoint

Plain-End Piping system for Steel Pipe

Catalog 2011

MODEL

79 WILDCAT

coupling

The Shurjoint Model 79 Wildcat coupling

pipe ends (* For sizes larger than 350mm

is designed to mechanically join plain-

(14), jaws are made of 17-4PH stainless

end or beveled end carbon steel pipe.

steel.)

The Wildcat couplings can be used for

The Shurjoint Wildcat coupling is

a variety of applications including mining,

recommended for use on steel pipe

process piping, manifold piping and oilfield

with a hardness less than HB 150, not

services. The Wildcat couplings feature

recommended for plastic, HDPE, cast iron or

case-hardened jaws* within the housings

other brittle pipe.

and large diameter heat treated track bolts

Gaskets are available either in Grade E

that when tightened securely grip the pipe

EPDM for water services of -29F to + 230F

surface. As with grooved couplings, a

(-34C to + 110C) or Grade T Nitrile for oil

C-shaped rubber gasket effectively seals the

services -20F to +180F (-29C to +82C).

Hardened
Steel Jaws
Gasket

Housing
Segment
Bolt / Nut

Steel Pipe 2" 16"


(Hardness HB 150 max.)

Pressure-Temperature Rating

Size
in / mm

Nom.
Rating


2

CWP

50
2 3

CWP
65 - 80

4

CWP

100

5 6

CWP
125 - 150
8 12

CWP
200 - 300

14

CWP

350

16

CWP

400

Working Pressure
(STD)
750 psi @100F
52 Bar @38C
600 psi @100F
42 Bar @38C
450 psi @100F
32 Bar @38C
300 psi @100F
21 Bar @38C
250 psi @100F
17 Bar @38C
200 psi @100F
14 Bar @38C
150 psi @100F
10 Bar @38C

Max. Service
Temperature

Bolts and nuts must always


be tightened to the required
torque.
EPDM: 230F / 110C
Nitrile: 180F / 82C

*Working pressure is for plain-end standard wall steel pipe with hardness
less than HB150.
*Proof test pressure: 1.5 times the working pressure, non-shock cold water.
*Burst pressure is engineered minimum 2 times the working pressure.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16

110
Copyright 2011 Shurjoint

Pipe
OD
mm / in
60.3
2.375
73.0
2.875
88.9
3.500
114.3
4.500
141.3
5.563
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750
355.6
14.000
406.4
16.000

Max. Working
Pressure
Bar / PSI
52
750
42
600
42
600
32
450
21
300
21
300
17
250
17
250
17
250
14
200
10
150

Max.
End Load
kN / Lbs
14.84
3320
17.57
3890
26.06
5770
32.82
7150
32.91
7290
46.69
10340
64.06
14600
99.46
22680
140.00
31900
138.97
30770
129.65
30140

Connect with the Best!

2"~ 16"

Required
Bolt
Bolt Torque
Size
A
N-m / Lbs-Ft.
No.
in
mm / in
200

95
2
x 3
150
3.75
200

108
2
x 3
150
4.25
270

127
2
x 4
200
5.00
270

154
2
x 4
200
6.14
340

187
2
x 6
250
7.36
340

216
2
x 6
250
8.50
270

276
4
x 4
200
10.88
400

320
4
x 6
300
12.60
470

371
4
1 x 6
350
14.60
470

424
4
1 x 6
350
16.70
470

475
4
1 x 6
350
18.70

Dimensions
B
mm / in
171
6.75
181
7.13
216
8.50
223
8.78
262
10.31
292
11.50
361
14.21
406
16.00
457
18.00
508
20.00
559
22.00

www.shurjoint.com

C
mm / in
98
3.86
98
3.86
98
3.86
102
4.00
111
4.38
111
4.38
127
5.00
127
5.00
135
5.30
156
6.15
156
6.15

Weight
Kgs / Lbs
3.2
7.0
3.3
7.3
5.0
11.0
6.5
14.3
11.0
24.2
13.0
28.6
19.0
41.8
24.0
52.8
28.7
63.1
42.5
93.5
43.5
95.7

Section 7
HDPE Series
HDPE Series........................................................................................112

H305 HDP Coupling.........................................................................113


H307 HDP Transition Coupling.........................................................114
H312 HDP Flange Adapter...............................................................115

Catalog 2011

Catalog 2011

HDPE Series
Shurjoint offers a series HDPE couplings and adapters for joining HDPE
pipe. The use of HDPE (high density polyethelyene) pipe continues to
grow in popularity as it's benefits over traditional materials are realized in
a variety of service applications. The features of HDPE pipe include a long
service life, flexibility, light in weight, increased resistance to corrosion
and chemicals, fatigue and superior flow characteristics. HDPE is now
commonly used in service applications including municipal water and
waste water, water distribution and transport, mining, slurry and many
other general and industrial applications.

Pressure Ratings (psi) - IPS Size












Pipe
Dimension
PE4710
Ratio (DR)
PE100
DR 7.3
317
DR 9
250
DR 11
200
DR 13.5
160
DR 17
125
DR 21
100
DR 26
80
DR 32.5
63

PE3608
PE3408
265
200
160
130
100
80
65
50

Design stress: PE4710 1000 psi, PE3608 & 3408 800 psi

Shurjoint HDPE couplings provide a fast

As the ductile iron coupling is much

and easy way to mechanically join HDPE

stronger than HDPE pipe itself, pressure

pipe. A series of sharply machined teeth

ratings of HDPE couplings are determined

securely grip the pipe as the bolts are

by the pressure rating of HDPE pipe

tightened, resulting in a leak-free joint. The

used. Pressure ratings of HDPE pipe

Shurjoint joining method eliminates the

vary depending on DR or SDR (standard

need for costly heat fusion equipment. The

dimension ratio) and design stress of the

highly restrained joint allows long lengths of

material.

pipe to be pulled from one area to another.


With the removal of a few bolts one can

DR (Pipe Dimension Ratio) DR =


t
Where:
D = pipe outside diameter, in
t = pipe minimum wall thickness, in

Pressure Ratings (Bar) - ISO Size








Pipe
Dimension
Ratio (SDR)
PE100
SDR 9
20
SDR 11
16
SDR 17
10
SDR 26
6.3

PE80
16
10
6.3
4

Design Stress: PE100 8.0 MPa, PE80 5.0 MPa

easily access the system for cleaning,

SDR (Standard Dimension Ratio) SDR =


Where:
D = pipe outside diameter, mm
t = pipe minimum wall thickness, mm

maintenance, changes and or system


expansion.

D
t

Shurjoint HDPE couplings are designed


to join IPS HDPE pipe, DR32.5 to 7.3,
conforming to ASTM D2513, D3350 and or
ANSI/AWWA C901 and ISO HDPE pipe,
SDR 9 to 26, conforming to ISO 4427-1/2.

How to install

Marking Use a marker and

Gasket Mounting Place a

Housing Mounting Lubricate

the gasket and or housings and

the nuts alternatively until the

on each pipe end, 1" from each

center the gasket in between

place the housings over gasket

housing bolt pads meet metal

end.

the marks. The pipe ends must

and insert bolts. Install nuts

to metal.

always be butted against each

finger tight.

measuring tape to place marks

gasket over the pipe ends and

Nut Tightening Ti g h t e n

other.

Refer to the Shurjoint installation


instruction manual for complete instructions. Shurjoint
HDPE couplings are not intended for use on PVC, PP
or other materials.

112
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

H305 HDP COUPLING


The Shurjoint Model H305 HDP couplings
feature four bolt housings and a series of
sharply machined teeth which securely grip

the pipe as the bolts and nuts are tightened.


The result is a leak-tight joint that is as
strong as or stronger than the pipe itself. The

H305 also features a contoured housing with


integral ramps along the outside diameter to
help the coupling slide over most obstacles
during the relocation of pipe runs.

H305 - IPS Size


























Nominal
Size
mm / in
50
2
80
3
100
4
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20

Pipe
O. D.
A
mm / in
mm / in
60.3
86
2.375
3.39
88.9
117
3.500
4.61
114.3
146
4.500
5.75
168.3
200
6.625
7.87
219.1
264
8.625
10.39
273.0
318
10.750
12.52
323.9
365
12.750
14.37
355.6
413
14.000
16.26
406.4
467
16.000
18.39
457.2
515
18.000
20.28
508.0
568
20.000
22.36

Dimensions
Coupling Bolts
B
C
Size
Weight
mm / in
mm / in
No.
in
Kgs / Lbs
133
117

2.6
4
x 2
5.24
4.61
5.7
165
102

3.6
4
x 2
6.50
4.02
7.9
203
146

5.2
4
x3
7.99
5.75
11.4
273
149

8.2
4
x 3
10.75
5.87
18.0
333
152

12.9
4
x 3
13.11
5.98
28.4
397
165

19.8
4
x 4
15.63
6.50
43.6
448
200

25.5
4
x 4
17.64
7.87
56.1
492
257

41.2
4
1 x 4
19.37
10.12
90.6
543
257

44.2
4
1 x 4
21.38
10.12
97.2
595
260

50.5
4
1 x 4
23.43
10.24
111.1
651
260

61.8
4
1 x 4
25.63
10.24
136.0

* Shurjoint recommends the use of a silicone based lubricant for the HDP series.

H305 - ISO Size






















Min.
mm
50
63
75
90
110
160
180
200
225
250
280
315
355
400
450
710
800
900

Pipe O. D.
Max.
A
mm
mm
50.5
72
63.6
85
75.7
97
90.9
113
111.0
139
161.5
190
181.7
211
201.8
236
226.4
261
252.3
289
281.7
319
317.9
354
357.2
412
402.4
462
452.7
515
716.4
800
807.2
889
908.1
991

Dimensions
Coupling Bolts
B
C
Size
mm
mm
No.
mm
115
105
4
M10 x 55
128
105
4
M10 x 55
140
105
4
M10 x 55
169
105
4
M12 x 75
181
112
4
M12 x 75
232
118
4
M12 x 75
253
118
4
M12 x 75
305
127
4
M16 x 90
330
127
4
M16 x 90
351
134
4
M16 x 120
406
134
4
M16 x 90
438
134
4
M20 x 120
489
256
4
M20 x 120
540
256
4
M24 x 120
595
256
4
M24 x 120
902
276
4
M30 x 100
991
276
4
M30 x 100
1092
276
4
M30 x 100

Approx.
Weight
Kgs
1.5
1.9
2.4
3.3
4.0
5.6
7.5
9.4
11.3
12.7
18.4
16.7
36.7
45.5
57.7
166.0
187.0
210.0

* Shurjoint recommends the use of a silicone based lubricant for the HDP series.

Connect with the Best!

www.shurjoint.com

113
Copyright 2011 Shurjoint

Catalog 2011

MODEL

H307 HDP TRANSITION COUPLING


The Shurjoint Model H307 transition
coupling provides for a fast, easy and direct

transition from HDP pipe and or fittings to

grooved end steel pipe (IPS).


A

H307 - IPS Size


















Nominal
Size
mm / in
50
2
80
3
100
4
150
6
200
8
250
10
300
12

Pipe
O. D.
A
mm / in
mm / in
60.3
86
2.375
3.39
88.9
114
3.500
4.49
114.3
146
4.500
5.75
168.3
203
6.625
8.00
219.1
267
8.625
10.51
273.0
321
10.750
12.64
323.9
375
12.750
14.76

Dimensions
Coupling Bolts
B
C
Size
Weight
mm / in
mm / in
No.
in
Kgs / Lbs
152
79

2.0
4
x 2
5.99
3.11
4.4
181
79

2.7
4
x3
7.13
3.11
5.9
216
95

3.8
4
x3
8.50
3.74
8.4
286
95

5.7
4
x 3
11.26
3.74
12.5
346
108

9.7
4
x 3
13.63
4.25
21.3
432
127

16.0
4
x 4
17.00
5.00
35.2
495
127

19.6
4
x 4
19.49
5.00
43.1

*Shurjoint recommends the use of a silicone based lubricant for use with the HDP series.

H307 - ISO Size













HDPE
mm
63.0
75.0
90.0
110.0
160.0
160.0
200.0
250.0
315.0

Pipe O. D.
STEEL
A
mm
mm
60.3
86
73.0
97
88.9
114
114.3
144
165.1
194
168.3
198
219.1
256
273.0
321
323.9
375

Dimensions
Coupling Bolts
B
C
Size
mm
mm
No.
mm
146
73
4
M10 x 55
146
73
4
M10 x 55
178
73
4
M12 x 75
203
76
4
M12 x 75
254
76
4
M12 x 75
257
76
4
M12 x 75
321
84
4
M16 x 90
432
127
4
M16 x 120
495
127
4
M20 x 120

* Shurjoint recommends the use of a silicone based lubricant for the HDP series.

114
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Approx.
Weight
Kgs
1.5
1.9
2.3
2.8
3.9
3.9
6.4
11.9
12.7

Catalog 2011

MODEL

H312 HDP FLANGE ADAPTER

The Shurjoint Model H312 HDP flange


adapter provides for the direct transition from

HDP pipe and or fittings to ANSI Class 125


or 150 flanged components.

H312 - IPS Size / ANSI Class 125/150
















Nominal
Size
mm / in
80
3
100
4
150
6
200
8
250
10
300
12

Pipe
O. D.
A
mm / in
mm / in
88.9
197
3.500
7.75
114.3
229
4.500
9.00
168.3
279
6.625
11.00
219.1
343
8.625
13.50
273.0
406
10.750
16.00
323.9
483
12.750
19.02

Dimensions
Flang Bolt

B
C
Size
Weight
mm / in
mm / in
No.
in
Kgs / Lbs
225
79

4.8
4

8.86
3.10
10.6
260
79

6.8
8

10.25
3.10
15.0
311
95

9.8
8

12.25
3.75
21.5
375
87

13.1
8

14.75
3.42
28.8
533
108

19.5
12

21.0
4.25
42.9
610
108

23.4
12

24.0
4.25
51.5

* Shurjoint recommends the use of a silicone based lubricant for use with the HDP series.
* Flange bolts and nuts are to be supplied by installer.

H312 - ISO Size / PN 10/16











HDPE
mm
75
90
110
160
200
250
315

Pipe O. D.
STEEL
A
mm
mm
76.1
185
88.9
200
114.3
220
168.3
285
219.1
340
273.0
405
323.9
460

Dimensions
Flange Bolt
B
C
Size
mm
mm
No.
mm
213
79
4
M16
228
79
8
M16
251
79
8
M16
317
95
8
M20
372
87
12 (PN 16)
M20
532
108
12
M24
587
108
12
M24

Approx.
Weight
Kgs
4.3
4.8
6.8
9.8
13.1
19.5
28.5

* Shurjoint recommends the use of a silicone based lubricant for use with the HDP series.
* Flange bolts and nuts are to be supplied by installer.

Connect with the Best!

www.shurjoint.com

115
Copyright 2011 Shurjoint

Catalog 2011

116
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Section 8
Copper Series
Grooved Couplings & Fittings for Copper Tubing. .............118
Pressure Ratings of Copper Tubing..........................................118
Roll Groove Standard for Copper Tubing...............................118
Grooved Couplings & Flanges for Copper Tubing
C305 Rigid Coupling..........................................................................119
C306 Reducing Coupling / 96 Continuity Clip................................. 120
C307 Transition Coupling................................................................. 121
C341 Flange Adapter........................................................................ 122
Grooved Fittings for Copper Tubing
C10-W / C11-W / C20-W Elbows, Tee........................................ 122
C10 / C11 / C20 / C60 Elbows, Tee, Cap..................................... 122
C21 / C50 / C26 Reducing Tees, Concentric Reducer.................. 123
C52 / C55 Concentric Reducer, Transition Adapter......................... 124
C55T / DE30-GG Transition Adapters, Dielectric Transition Fitting.... 126

Mechanical Tees & Flow Control Components

C723 Mechanical Tee....................................................................... 126


C726 Y-Strainer................................................................................ 127
SJ-C300 Butterfly Valve.................................................................. 128

Catalog 2011

Catalog 2011

Grooved Couplings,
Fittings & Components
for Copper Tubing
The Shurjoint copper series
is the most complete line of
grooved components available
for installation on copper tubing
(CTS) in sizes 2 - 6 (50 - 150
mm). Shurjoint grooved mechanical
components provide a fast, easy,
economical and durable joining
method of copper tubing without
the use of heat or solder.
Grooved-end fittings are produced from
wrought copper and or bronze castings.
Wrought copper conforms to ASTM B75
UNC C12200 (99.9% copper). Bronze
castings are produced from lead-free alloys
C90500 and or C89836 Bismuth bronze per
ASTM B584. Materials are in compliance
with ANSI/NSF 61 for potable water service
applications.

Standard Roll Groove for


U.S. Standard Copper
Tubing
t

O.D.

B
C

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6

118
Copyright 2011 Shurjoint

Pipe
O. D.
mm / in
54.0
2.125
66.7
2.625
79.4
3.125
104.8
4.125
130.2
5.125
155.6
6.125

Copper Tubing - Dimensions & Pressure Ratings (ASTM B88 & B306)

Nominal
D

Size
Type
Pipe OD

mm / in
mm / in

K

50
L
54

2
M
2.125

DWV

K

65
L
66.7

2
M
2.625

DWV

K

80
L
79.4

3
M
3.125

DWV

K

100
L
104.8

4
M
4.125

DWV

K

125
L
130.2

5
M
5.125

DWV

K

150
L
155.6

6
M
6.125

DWV

t
Thickness

mm
2.11
1.78
1.47
1.07
2.41
2.03
1.65
N/A
2.77
2.29
1.83
1.14
3.40
2.79
2.41
1.47
4.06
3.12
2.77
1.83
4.88
3.56
3.10
2.11

in
0.083
0.070
0.058
0.042
0.095
0.080
0.065
N/A
0.109
0.090
0.072
0.045
0.134
0.110
0.095
0.058
0.160
0.123
0.109
0.072
0.192
0.140
0.122
0.083

P
Max. Pressure
Bar
psi
33
484
28
406
23
335
17
241
31
447
26
375
21
303
N/A
N/A
30
431
24
354
19
282
12
175
28
400
23
327
19
282
12
171
26
384
20
294
18
260
12
171
27
386
19
279
17
243
11
164

Notes: 1. Design stress: 6000 psi (41.4 MPa)



2. Pressures are based on water at 23C (73.4F).

Roll Set

As copper tubing is thinner than carbon steel pipe, always use


a roll set specifically designed for use on copper tubing.
Pipe OD
Maximum allowable tolerances from square cut ends is 0.03" for
2" thru 3"; 0.045" for 4" thru 6"; and 0.060" for sizes 8".
Gasket Seating Surface
The gasket seating surface shall be free from deep scores,
marks, or ridges that could prevent a positive seal.
Groove Width
Groove width is to be measured between vertical flanks of the
groove side walls.
Groove Diameter
The 'C' diameters are average values. The groove must be of
uniform depth around the entire pipe circumference.

Gasket Seat A
0.79 mm
0.03 in
15.5
0.610
15.5
0.610
15.5
0.610
15.5
0.610
15.5
0.610
15.5
0.610

Connect with the Best!

Groove Width B
0.79 mm
0.03 in
7.6
0.300
7.6
0.300
7.6
0.300
7.6
0.300
7.6
0.300
7.6
0.300

Groove Dia. C
+0/-0.51 mm
+0/-0.02 in
51.5
2.029
64.1
2.525
76.8
3.025
102.1
4.019
127.0
4.999
152.3
5.999

Groove Depth
The 'd' is for reference use only. The groove dimension shall be
determined by the groove diameter 'C'.
Minimum Wall Thickness
The DWV pipe (ASTM B-306) is minimum wall thickness that
may be roll grooved.
Flare Diameter
The pipe end that may flare when the groove is rolled shall be
within this limit when measured at the extreme end of the pipe.

Groove Depth
Min. Allow
d (ref)
Wall Thick t
mm / in
mm / in
1.2
1.6
0.048
0.064
1.3
1.7
0.050
0.065
1.3
DWV
0.050
1.4
DWV
0.053
1.4
DWV
0.053
1.6
DWV
0.063

www.shurjoint.com

Max. Allowed
Flare Dia.
mm / in
56.4
2.220
69.1
2.720
81.8
3.220
107.2
4.220
132.6
5.220
158.0
6.220

Catalog 2011

MODEL

C305 RIGID COUPLING FOR COPPER TUBING (CTS)


The Model C305 features angle bolt pad

housings and EPDM GapSeal gaskets and

design for a rigid joint and easy swing-

are rated up to 300 psi (20 bar), depending

over installation. The C305 couplings are

on the type and size of copper tubing used.

comprised of epoxy coated ductile iron


Pressure-Temperature Rating


Nom. Rating



Class 150

Working
Pressure

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C

*Working pressure is for connection with roll-grooved Type K copper tubing.


*Proof test pressure: 1.5 times the working pressure.
*Burst pressure: 3 times the listed working pressure, min.

TYPE K, L, M (ASTM B-88) & TYPE DWV (ASTM B306)
















Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6

BS EN 1057








Nominal
Size
mm
50
65
80
100
125
150

Pipe
OD
mm / in
54.0
2.125
66.7
2.625
79.4
3.125
104.8
4.125
130.2
5.125
155.6
6.125

Pipe
O. D.
mm
54.0
66.7
76.1
108.0
133.0
159.0

Pipe End
Separation
A
mm / in
mm / in
1.5
81
0.06
3.17
1.5
93
0.06
3.66
1.5
107
0.06
4.21
1.5
132
0.06
5.20
1.5
159
0.06
6.26
1.5
184
0.06
7.24

Dimensions
Bolt / Nut
B
C
Size
mm / in
mm / in
in
118
48

x 2
4.63
1.89
134
48

x 2
5.28
1.89
154
48

x3
6.06
1.89
185
48

x3
7.28
1.89
220
48

x 3
8.66
1.89
248
48

x 3
9.76
1.89

Pipe End
Separation
A
mm
mm
1.5
81
1.5
93
1.5
104
3.2
138
3.2
165
3.2
190

Dimensions
B
C
mm
mm
118
48
134
48
141
48
192
48
231
48
253
48

Bolt / Nut
Size
mm
M10 x 55
M10 x 55
M10 x 55
M12 x 75
M16 x 90
M16 x 90


Weight
kgs
0.8
0.9
1.3
1.6
2.2
2.5

Dimensions
B
C
mm
mm
115
48
134
48
154
48
183
48
220
48
249
48

Bolt / Nut
Size
mm
M10 x 55
M10 x 55
M12 x 75
M12 x 75
M16 x 90
M16 x 90


Weight
kgs
0.8
0.9
1.3
1.6
2.1
2.5

AS1432 TYPE "A" , "B" AND "D"










Nominal
Size
mm
50
65
80
100
125
150

Pipe
O. D.
mm
50.80
63.50
76.20
101.60
127.00
152.40

Pipe End
Separation
A
mm
mm
1.5
77
1.5
90
1.5
103
1.5
129
1.5
156
1.5
181

Connect with the Best!

www.shurjoint.com


Weight
Kgs / Lbs
0.8
1.8
0.9
2.0
1.3
2.8
1.6
3.5
2.2
4.6
2.5
5.5

119
Copyright 2011 Shurjoint

Catalog 2011

MODEL

C306 REDUCING COUPLING FOR COPPER TUBING (CTS)


The Model C306 Reducing Coupling

local cell and stray current problems. The

allows direct reduction on a piping run and

specially designed rubber gasket prevents

eliminates the need for a concentric reducer

the smaller pipe from telescoping into the

and couplings. The epoxy coated ductile iron

larger pipe during vertical installation.

coupling housings help eliminate galvanic


Pressure-Temperature Rating


Nom. Rating



Class 150

Working
Pressure

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C

*Working pressure is for connection with roll-grooved Type K copper tubing.


*Proof test pressure: 1.5 times the working pressure.
*Burst pressure: 3 times the listed working pressure, min.


Nominal
Pipe

Size
OD
mm / in
mm / in

65 x 50
66.7 x 54.0

2 x 2
2.625 x 2.215

80 x 50
79.4 x 54.0

3 x 2
3.125 x 2.125

80 x 65
79.4 x 66.7

3 x 2
3.125 x 2.625
100 x 65
104.8 x 66.7

4 x 2
4.125 x 2.625
100 x 80
104.8 x 79.4

4 x 3
4.125 x 3.125
125 x 100 130.2 x 104.8

5 x 4
5.125 x 4.125
150 x 100 155.6 x 104.8

6 x 4
6.125 x 4.125

Max.
Working
Pressure
Bar / PSI
20
300
20
300
20
300
20
300
20
300
20
300
20
300

Max.
End
Load
kN / Lbs
6.98
1622
9.89
2300
9.89
2300
17.23
4007
17.23
4007
26.60
6186
37.99
8835

Pipe
Deflection
Dimensions
End
Deg. Per
Per
Bolt
Separation
Coupling
Pipe
A
B
C
Size
mm / in
( )
mm / m in / ft
mm / in
mm / in
mm / in
in
1.6

24.0
94
141
45

1 22'
x3
0.06
0.29
3.70
5.55
1.77
1.6

20.0
107
152
45

1 09'
x3
0.06
0.24
4.21
5.98
1.77
1.6

20.0
107
152
45

1 09'
x3
0.06
0.24
4.21
5.98
1.77
1.6

15.0
132
183
45

0 53'
x3
0.06
0.18
5.20
7.20
1.77
1.6

15.0
132
183
45

0 53'
x3
0.06
0.18
5.20
7.20
1.77
1.6

12.0
160
224
45

0 42'
x 3
0.06
0.15
6.30
8.82
1.77
1.6

10.3
185
251
45

0 36'
x 3
0.06
0.13
7.28
9.88
1.77

MODEL

96 CONTINUITY CLIP
Couplings with rubber gaskets are likely to
function as an insulator. Where electrical
continuity is required, the Shurjoint
continuity clip will restore electrical
continuity to the system. The electrical
continuity clip satisfies IEE Wiring
Regulations. Material: Copper or Brass
plate.
Note: The pipe surface where continuity clips come
in contact must be conductive. If the surface is
painted, the paint should be removed to expose
bare metal.

120
Copyright 2011 Shurjoint

Connect with the Best!

Model
96-1
96-2
96-3

Coupling Size
1" - 3"
4" - 6"
8" - 12"

Box Qty/pcs
125
125
100

www.shurjoint.com

Weight
Kgs / Lbs
1.3
2.9
1.5
3.3
1.4
3.0
1.9
4.2
1.8
4.0
2.5
5.5
3.3
7.3

Catalog 2011

MODEL

C307 TRANSITION COUPLING (IPS X CTS)


The Model C307 Transition Coupling provides
for a direct connection and transition between
grooved end IPS steel pipe, fittings or valves
and grooved end CTS copper tubing. The

IPS
Steel
Pipe

rubber gasket isolates the fluid from coupling


housings and the epoxy coated housings help.
eliminate galvanic local cell and stray current

CTS
Copper
Tubing
C307

problems. The C307 is rated to 300 psi (20


bar).
Pressure-Temperature Rating


Nom. Rating



Class 150

Working
Pressure

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C

Nominal
Size
mm / in
50
2
65
2
80
3
100
4

Pipe OD
IPS x CTS
mm / in
60.3 x 54.0
2.375 x 2.125
73.0 x 66.7
2.875 x 2.625
88.9 x 79.4
3.500 x 3.125
114.3 x 104.8
4.500 x 4.125

IPS
B'fly
Valve

CTS
Copper
Tubing

*Working pressure is for connection with roll-grooved Type K copper tubing.


*Proof test pressure: 1.5 times the working pressure.
*Burst pressure: 3 times the listed working pressure, min.

C307

Pipe End
Separation
Deflection
A
mm / in
( )
mm / in
0 - 1.6

84
1 31'
0 - 0.06
3.31
0 - 1.6

99
1 15'
0 - 0.06
3.90
0 - 1.6

116
1 02'
0 - 0.06
4.57
0 - 1.6

145
1 36'
0 - 0.06
5.71

CTS
Copper
Tubing
C307

Dimensions
Bolt / Nut
B
C
Size
Weight
mm / in
mm / in
in
Kgs / Lbs
129
48

0.9
x 2
5.08
1.89
2.0
142
48

1.0
x 2
5.59
1.89
2.2
169
48

1.4
x3
6.65
1.89
3.0
197
52

1.9
x3
7.76
2.05
4.2

MODEL

C341 Flange adapter FOR COPPER TUBING (CTS)


The Shurjoint Model C341 Flange Adapter

heat or solder. The pressure responsive

allows for the direct connection of grooved-

gasket seals on the outside diameter of

end copper tubing with ANSI class 125/150

the copper tubing and isolates the flange

(steel) or ASME B16.24 (copper) class 150

segments from the internal fluid.

flanged components without the need for

Pressure-Temperature Rating


Nom. Rating



Class 150

Working
Pressure

Max. Service
Temperature

300 psi @100F


20 Bar @38C

EPDM: 230F / 110C

D E

*Working pressure is for connection with roll-grooved Type K copper tubing.


*Hydrostatic Shell Test: 1.5 times the working pressure, nonshock cold water.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6

Pipe
OD
A
mm / in
mm / in
54.0
152
2.125
6.00
66.7
178
2.625
7.00
79.4
190
3.125
7.50
104.8
229
4.125
9.00
130.2
254
5.125
10.00
155.6
279
6.125
11.00

Dimensions
B
C
mm / in
mm / in
121
19
4.75
0.75
140
22
5.50
0.87
152
24
6.00
0.94
191
24
7.50
0.94
216
24
8.50
0.94
241
25
9.50
1.00

Sealing Surface
Bolts
D
E
Size
mm / in
mm / in
No.
in
54
81

4
x3
2.13
3.20
67
99

4
x3
2.63
3.91
80
115

4
x3
3.13
4.53
105
140

4
x3
4.13
5.53
130
170

8
x 3
5.13
6.71
156
198

8
x 3
6.13
7.79

Weight
Kgs / Lbs
2.1
4.6
3.0
6.6
3.5
7.7
4.3
9.5
5.8
12.8
6.2
13.6

* Please note that 2, 2-1/2, and 3 Model C341 Flanges cannot be used for making direct connections to Model SJ-C300 Butterfly Valves due to bolt pad interference with the valve.

Connect with the Best!

www.shurjoint.com

121
Copyright 2011 Shurjoint

Catalog 2011

Grooved Fittings for Copper Tubing


Shurjoint Grooved-end fittings are produced
from wrought copper and or bronze castings.
Wrought copper conforms to ASTM B75
UNC C12200 (99.9% copper). Bronze
castings are produced from lead-free alloys

C90500 and or C89836 Bismuth bronze per

components and ASTM B-88 roll grooved

ASTM B584. Materials are in compliance

copper tubing type K, L, M and ASTM B-306

with ANSI/NSF 61 for potable water service

DWV.

applications. Shurjoint fittings are designed


for use with Shurjoint CTS couplings,

MODELs

Nominal
Size
mm / in
50
2
65
2
80
3
100
4

Pipe
OD
mm / in
54.0
2.125
66.7
2.625
79.4
3.125
104.8
4.125

C10-W 90 Elbow
C-E
Weight
mm / in
Kgs / Lbs
74
0.34
2.91
0.75
84
0.52
3.31
1.15
97
0.85
3.81
1.88
121
1.85
4.75
4.07

C-E

C-

C-

C-E

C-E

C-

C10-W 90 ELBOW (Wrought)


C11-W 45 ELBOW (Wrought)
C20-W Tee (Wrought)
C-E

C-E

C11-W 45 Elbow
C-E
Weight
mm / in
Kgs / Lbs
56
0.28
2.19
0.61
59
0.40
2.31
0.89
66
0.63
2.59
1.38
81
1.36
3.19
2.99

C-E
mm / in
68
2.69
81
3.20
89
3.52
108
4.25

C-E
E-E

C20-W Tee

E-E

Weight
Kgs / Lbs
0.66
1.45
1.07
2.37
1.53
3.38
2.62
5.77

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6

122
Copyright 2011 Shurjoint

Pipe
OD
mm / in
54.0
2.125
66.7
2.625
79.4
3.125
104.8
4.125
130.2
5.125
155.6
6.125

C10 90 Elbow
C-E
Weight
mm / in
Kgs / Lbs
74
0.7
2.91
1.5
84
0.9
3.31
2.0
97
1.2
3.81
2.6
121
2.5
4.75
5.5
151
5.2
5.94
11.5
176
7.5
6.94
16.5

Connect with the Best!

C-E
mm / in
62
2.44
81
3.20
89
3.50
108
4.25
151
5.94
176
6.94

C-E

E-E
E-E E-E

E-E

C-E

C-E
C11 45 Elbow
C-E
Weight
mm / in
Kgs / Lbs
56
0.8
2.19
1.7
59
1.0
2.31
2.1
66
1.4
2.59
3.2
81
2.5
3.19
5.5
83
3.6
3.25
7.9
92
4.6
3.63
10.2

C-E
C-E C-E

C-E
C-E

C-E

C
-E

C-E C-E
C-E

C
-E

C10 90 ELBOW (Cast)


C11 45 ELBOW (Cast)
C20 TEE (Cast)
C60 CAP (Cast)

C
C-E
-E

MODELs

C20 Tee

Weight
Kgs / Lbs
0.8
1.8
1.3
2.9
1.7
3.7
3.3
7.3
7.8
17.2
11.9
26.2

www.shurjoint.com

E-E
in
24
0.96
24
0.96
24
0.96
24
0.96
24
0.96
24
0.96

C60 Cap

Weight
Kgs / Lbs
0.3
0.6
0.4
0.9
0.6
1.2
1.0
2.1
1.6
3.5
2.0
4.4

E-E

Catalog 2011

MODELs

C21 REDUCING TEE (Cast)


C50 CONCENTRIC

REDUCER (Cast)

C-E

C-E
E-E

Nominal
Size
mm / in
65 x 50
2 x 2
80 x 50
3 x 2
80 x 65
3 x 2
100 x 50
4 x 2
100 x 65
4 x 2
100 x 80
4 x 3
125 x 80
5 x 3
125 x 100
5 x 4
150 x 65
6 x 2
150 x 80
6 x 3
150 x 100
6 x 4
150 x 125
6 x 5

Pipe
O. D.
mm / in
66.7 x 54.0
2.625 x 2.125
79.4 x 54.0
3.125 x 2.125
79.4 x 66.7
3.125 x 2.625
104.8 x 54.0
4.125 x 2.125
104.8 x 66.7
4.125 x 2.625
104.8 x 79.4
4.125 x 3.125
130.2 x 79.4
5.125 x 3.125
130.2 x 104.8
5.125 x 4.125
155.6 x 66.7
6.125 x 2.625
155.6 x 79.4
6.125 x 3.125
155.6 x 104.8
6.125 x 4.125
155.6 x 130.2
6.125 x 5.125

Nominal
Size
C-E
mm / in
mm / in
50 x 50 x 20
56
2 x 2 x
2.20
50 x 50 x 25
59
2 x 2 x 1
2.33
50 x 50 x 32
63
2 x 2 x 1
2.48
50 x 50 x 40
66
2 x 2 x 1
2.60
65 x 65 x 20
58
2. x 2 x
2.28
65 x 65 x 25
61
2 x 2 x 1
2.40
65 x 65 x 32
64
2 x 2 x 1
2.52
65 x 65 x 40
69
2 x 2 x 1.5
2.70
65 x 65 x 50
75
2 x 2 x 2
2.95
80 x 80 x 20
62
3 x 3 x
2.44
80 x 80 x 25
65
3 x 3 x 1
2.54
80 x 80 x 32
67
3 x 3 x 1
2.63
80 x 80 x 40
72
3 x 3 x 1
2.85
80 x 80 x 50
79
3 x 3 x 2
3.11
100 x 100 x 20
76
4 x 4 x
3.00
100 x 100 x 25
79
4 x 4 x 1
3.10
100 x 100 x 32
83
4 x 4 x 1
3.25
100 x 100 x 40
85
4 x 4 x 1
3.35
100 x 100 x 50
92
4 x 4 x 2
3.62

C21 Reducing Tee


C-E
Weight
mm / in
Kgs / Lbs
81
1.6
3.20
3.6
89
2.2
3.50
4.8
89
2.2
3.50
4.8
108
3.5
4.25
7.7
108
3.6
4.25
7.9
108
3.7
4.25
8.1
151
7.6
5.94
16.7
151
7.8
5.94
17.2
176
10.4
6.94
22.9
176
10.7
6.94
23.5
176
10.7
6.94
23.5
176
11.9
6.94
26.2

C50 Concentric Reducer


E-E
Weight
mm / in
Kgs / Lbs
64
0.6
2.50
1.2
64
0.7
2.50
1.5
64
0.7
2.50
1.5
76
1.2
3.00
2.5
76
1.2
3.00
2.6
76
1.1
3.00
2.5
89
2.0
3.50
4.4
89
2.0
3.50
4.4
102
2.7
4.00
6.0
102
2.7
4.00
5.9
102
2.7
4.00
5.8
102
2.7
4.00
5.9

MODELs

MODELs

C26 REDUCING TEE

(GR X GR X CUP)
(Cast)

C-E
C-B

Cup

Connect with the Best!

C26 Red. Tee (Gr X Gr x Cup)


C-B
Cup
Weight
mm / in
mm / in
Kgs / Lbs
51
19
0.7
2.00
0.75
1.6
55
23
0.7
2.16
0.91
1.6
56
25
0.8
2.22
0.97
1.7
59
28
0.9
2.34
1.09
2.0
57
34
0.9
2.25
1.34
1.9
61
23
1.0
2.41
0.91
2.2
63
25
1.1
2.47
0.97
2.3
66
28
1.2
2.59
1.09
2.6
72
34
1.4
2.84
1.34
3.0
64
19
1.3
2.50
0.75
2.9
66
23
1.3
2.60
0.91
2.9
69
25
1.4
2.72
0.97
3.1
72
28
1.5
2.84
1.09
3.3
78
34
1.7
3.09
1.34
3.7
76
19
2.2
3.00
0.75
4.8
80
23
2.3
3.16
0.91
5.1
82
25
2.5
3.22
0.97
5.5
85
28
2.5
3.34
1.09
5.6
91
34
2.7
3.59
1.34
5.9

www.shurjoint.com

123
Copyright 2011 Shurjoint

Catalog 2011

MODELs

C52 CONCENTRIC REDUCER (GR X GR X CUP) (Cast)
























Nominal
Size
E-E
mm / in
mm / in
50 x 50 x 25
69
2 x 2 x 1
2.70
50 x 50 x 32
76
2 x 2 x 1
3.00
50 x 50 x 40
75
2 x 2 x 1
2.94
65 x 65 x 25
83
2 x 2 x 1
3.25
65 x 65 x 32
89
2 x 2 x 1
3.52
65 x 65 x 40
88
2 x 2 x 1.5
3.45
65 x 65 x 50
84
2 x 2 x 2
3.30
80 x 80 x 40
93
3 x 3 x 1
3.68
80 x 80 x 50
104
3 x 3 x 2
4.10
100 x 100 x 50
121
4 x 4 x 2
4.75

C52 Conc. Reducer (Gr X Gr X Cup)


Cup
Weight
mm / in
Kgs / Lbs
23
0.3
0.91
0.7
25
0.4
0.97
0.8
28
0.4
1.09
0.8
23
0.5
0.91
1.2
25
0.5
0.97
1.2
28
0.5
1.09
1.2
34
0.5
1.34
1.2
28
0.8
1.09
1.7
34
0.9
1.34
1.9
34
1.4
1.34
3.2

E-E

Cup

MODEL

C55 TRANSITION ADAPTER (IPS X CTS )


The Model C55 Transition Adapter provides
a direct transition between male threadedend steel pipe (IPS) and grooved-end
copper tubing. The C55 is UL classified
to ANSI/NSF 61 for use in potable water
systems.


Nominal Pipe Size
IPS (NPT) x CTS (GRV)

mm / in

40 x 50

1 x 2

50 x 50

2 x 2

65 x 65

2 x 2

80 x 80

3 x 3

124
Copyright 2011 Shurjoint

Actual Pipe O.D.


Steel Pipe (IPS) O.D.
Copper Tubing (CTS) D
mm / in
mm / in
48.3
54.0
1.900
2.125
60.3
54.0
2.375
2.125
73.0
66.7
2.875
2.625
88.9
79.4
3.500
3.125

Connect with the Best!

E-E
mm / in
63
2.50
63
2.50
70
2.75
76
3.00

Weight
Kgs / Lbs
0.6
1.3
0.7
1.4
1.1
2.4
1.5
3.3

NPT
(IPS)

D(CTS)

E-E

www.shurjoint.com

Catalog 2011

MODEL

C55T TRANSITION ADAPTER (IPS/FT X CTS/GR ) WITH " TAPS


Allows for the installation of gauges or
Pete's Plugs for measuring temperature and

" NPT

or pressure.

NPT

D(CTS)

(IPS)
" NPT
E to E


Nominal Pipe Size
IPS (NPT) x CTS (GRV)

mm / in

40 x 50

1 x 2

50 x 50

2 x 2

65 x 65

2 x 2

80 x 80

3 x 3

Actual Pipe O.D.


Steel Pipe (IPS) O.D.
Copper Tubing (CTS) D
mm / in
mm / in
48.3
54.0
1.900
2.125
60.3
54.0
2.375
2.125
73.0
66.7
2.875
2.625
88.9
79.4
3.500
3.125

E-E
mm / in
63
2.50
63
2.50
70
2.75
76
3.00

Weight
Kgs / Lbs
0.5
1.1
0.6
1.3
0.9
2.0
1.5
3.3

Pete's Plug

(CTS)

(IPS)
C55T

C305

MODEL

DE30-GG DIELECTRIC

TRANSITION FITTING (IPS X CTS)

The Model DE30-GG Dielectric Transition

end copper tubing (CTS). The internal PP

Fitting provides a direct transition between

lining effectively eliminates galvanic local

grooved-end steel pipe (IPS) and grooved-

cell and stray current problems.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6
200
8

Actual Pipe O.D.


IPS
CTS
mm / in
mm / in
60.3
54.0
2.375
2.125
73.0
66.7
2.875
2.625
88.9
79.4
3.500
3.125
114.3
104.8
4.500
4.125
141.3
130.2
5.563
5.125
168.3
155.6
6.625
6.125
219.1
206.4
8.625
8.125

Connect with the Best!

E-E
mm / in
102
4.00
102
4.00
102
4.00
102
4.00
102
4.00
102
4.00
102
4.00

Weight
Kgs / Lbs
0.6
1.3
0.9
1.9
1.3
2.9
1.5
3.3
2.4
5.2
3.1
6.9
4.3
9.4

Ductile Iron Body


Virgin PP Lining

E-E

www.shurjoint.com

125
Copyright 2011 Shurjoint

MODEL

C723 BRONZE MECHANICAL TEE FOR COPPER TUBING (CTS)


The Shurjoint Model C723 provides a fast,

and nuts. The fitting is available with a

easy and reliable branch connection from

female threaded outlet, NPT or BSPT.

Catalog 2011

copper tubing (CTS). The fitting consists of


a bronze upper housing, ductile iron lower
housing, o-ring and carbon steel track bolts
Pressure-Temperature Rating
Nom.

Rating

Working
Pressure

Test Pressure
@73F / 23C

Max. Service
Temperature

Class
150

300 psi @100F


20 Bar @38C

450 psi
32 Bar

EPDM: 230F / 110C

*Working pressure is for connection with Type K copper tubing.


Proof test pressure: 1.5 times the working pressure, non-shock cold water.
Burst pressure is engineered minimum 3 times the working pressure.

Nominal
Size
mm / in
65 x 20
2 x
65 x 25
2x 1
65 x 32
2 x 1
80 x 20
3 x
80 x 25
3 x 1
80 x 32
3 x 1
100 x 20
4 x
100 x 25
4 x 1
100 x 32
4 x 1

Hole Dia.
+1.6, -0 / +0.063, -0
A
B
mm / in
mm / in
mm / in
30
66
40
1.18
2.60
1.57
30
66
40
1.18
2.60
1.57
45
73
40
1.77
2.87
1.57
30
73
45
1.18
2.87
1.77
30
73
45
1.18
2.87
1.77
45
84
45
1.77
3.31
1.77
30
86
60
1.18
3.39
2.36
30
86
60
1.18
3.39
2.36
45
97
60
1.77
3.81
2.36

Dimensions
Bolt
C
D
T*
Size
Weight
mm / in
mm / in
mm / in
in
Kgs / Lbs
118
44
52

0.7
x 2
4.65
1.73
2.05
1.5
118
44
49

0.7
x 2
4.65
1.73
1.93
1.5
118
63
55

1.0
x 2
4.65
2.48
2.15
2.2
130
44
58

0.7
x 2
5.12
1.73
2.28
1.5
130
44
56

0.8
x 2
5.12
1.73
2.20
1.8
130
63
66

1.0
x 2
5.12
2.48
2.59
2.2
158
44
71

0.8
x 2
6.22
1.73
2.80
1.8
158
44
79

0.8
x 2
6.22
1.73
3.11
1.8
158
63
79

0.8
x 2
6.22
2.48
3.11
1.8

*T: Take-out , Center of run to engaged pipe end (approx.)

Use a torque wrench and


tighten the nuts to an approx. torque value
of 5 ~ 9 lbs-ft (7 ~ 12 N-m). Excess torque
may cause joint failure.

126
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

MODEL

C726 Y - STRAINER FOR COPPER TUBING (cts)


The Shurjoint C726 Y-Strainer can be installed
quickly and easily with two mechanical
couplings and the straight flow through design
provides for lower pressure drop.
Pressure-Temperature Rating
Nom.

Ratings

Working Pressure
(Type K Copper Tubing)

Shell Test
(Hydrostatic)

Max. Service
Temperature



Class 150

300 psi @100F


20 Bar @38C

450 psi
32 Bar

EPDM: 230F / 110C

*Working pressure is for connection with roll-grooved Type K copper tubing.


*Proof test pressure: 1.5 times the working pressure.
*Burst pressure: 3 times the listed working pressure, min.

Nominal
Size
mm / in
50
2
65
2
80
3
100
4
150
6

Pipe
O. D.
mm / in
54.0
2.125
66.7
2.625
79.4
3.125
104.8
4.125
155.6
6.125

Max.
Working Pressure
A
Bar / PSI
mm / in
20
222
300
8.75
20
248
300
9.75
20
270
300
10.63
20
330
300
13.00
20
432
300
17.00

Connect with the Best!

Dimensions
B
C
mm / in
mm / in
162
81
6.38
3.18
170
96
6.69
3.78
196
114
7.71
4.50
244
152
9.60
6.00
328
203
12.91
8.00

Drain
Plug Size
mm / in
15

15

15

25
1
25
1

www.shurjoint.com

Approx.
Weight
Kgs / Lbs
4.0
8.8
5.1
11.3
6.8
15.0
12.5
27.5
26.9
59.3

127
Copyright 2011 Shurjoint

Catalog 2011

MODEL

SJ-C300 BUTTERFLY VALVE FOR COPPER TUBING (cts)


The Shurjoint Model SJ-C300 is a lever

copper alloy C90500 (88-10-0-2) or C89836

handle bronze body butterfly valve designed

Bismuth bronze which are UL classified in

for use with grooved copper tubing (CTS),

accordance with ANSI/NSF 61 and annex G

fittings and couplings. The lead-free

for potable water use.

bronze body conforms to ASTM B-584


Pressure-Temperature Rating
Nom.

Ratings


CWP

Working Pressure
(Type K Copper Tubing)

Shell Test
@73F / 23C

Max. Service
Temperature

300 psi @100F


20 Bar @38C

450 psi
32 Bar

EPDM: 230F / 110C

*Working pressure is for connection with roll-grooved Type K copper tubing.


*Seat test: 100% working pressure.

A SJ-C300 butterfly valve installed in a hot water system
















Nominal
Size
mm / in
50
2
65
2
80
3
100
4
125
5
150
6

128
Copyright 2011 Shurjoint

Pipe
O. D.
A
mm / in
mm / in
54
81
2.125
3.19
66.7
97
2.625
3.82
79.4
97
3.125
3.82
104.8
116
4.125
4.57
130.2
148
5.125
5.83
155.6
148
6.125
5.83

Connect with the Best!

O. D.

B
mm / in
135
5.31
149
5.87
163
6.42
208
8.19
248
9.77
274
10.79

Dimensions

C
mm / in
57
2.45
73
2.87
83
3.27
111
4.37
136
5.36
163
6.42

D
mm / in
254
10.0
254
10.0
254
10.0
254
10.0
254
10.0
254
10.0

www.shurjoint.com

Weight
Kgs / Lbs
2.7
5.9
3.3
7.3
3.5
7.7
5.0
11.0
7.7
16.9
7.7
16.9

Section 9
AWWA Ductile Iron Series
AWWA Ductile Iron Series..................................................................... 130
Radius Cut Groove Specifications....................................................... 130
AWWA Grooved Couplings & Flange Adapters

A505 Coupling.................................................................................. 131


A507 Transition Coupling................................................................. 132
A512 Flange Adapter........................................................................ 132

Grooved Fittings

A10 / A11 / A12 / A13 / A60 Elbows, Cap................................... 133


A20 / A25 / A50 / A10R Tee, Reducing Tee,

Concentric Reducer, Reducing Elbow................................................ 134

Catalog 2011

Catalog 2011

AWWA Ductile Iron Series


Shurjoint offers a variety of grooved mechanical
couplings and fittings for AWWA ductile iron pipe in
sizes 3 to 24. The Shurjoint coupling features a
two-piece housing and GapSeal gasket for a leaktight seal. Ductile iron pipe shall be cut-grooved to
AWWA C-606 Table 2 and Table 3 - Radius Cut Groove
Specifications.
Rubber gaskets are specially compounded to seal on
ductile iron surfaces and are available in three grades
to meet your service requirement needs. See page 131
for details.

Radius Cut Groove Specification For Ductile Iron Pipe


B
R

A B
T
O.D.

Gasket Seating Surface (Column 3)


The same coupling can be used either as a rigid joint or a flexible joint depending on the groove. Gasket seat "A Rigid" is for rigid joints
and Gasket seat "A Flex." for flexible joints.
The gasket seating surface shall be free from deep scores, marks, or ridges that could prevent a positive seal.
Groove Diameter (Column 5)
The 'C' diameters are average values. The groove must be of uniform depth around the entire pipe circumference.
Radius (Column 6)
The groove must be cut with a radius "R" at the corners of the groove to reduce stress concentration.
Minimum Wall Thickness (Column 7)
"T" is the minimum allowable wall thickness that may be cut-grooved; tolerances are to conform to ANSI /AWWA C151/A21.51.

AWWA Ductile Iron Pipe



Pipe O. D.
Nominal

Size
Basic
Tolerance

+
-

mm / in
mm / in
mm / in
mm / in

80
100.6
+1.14
-1.14

3
3.96
+0.045
-0.045

100
121.9
+1.14
-1.14

4
4.80
+0.045
-0.045

150
175.3
+1.52
-1.52

6
6.90
+0.060
-0.060

200
229.9
+1.52
-1.52

8
9.05
+0.060
-0.060

250
281.9
+1.52
-1.52

10
11.10
+0.060
-0.060

300
335.3
+1.52
-1.52

12
13.20
+0.060
-0.060

350
388.6
+1.27
-2.03

14
15.30
+0.050
-0.080

400
442.0
+1.27
-2.03

16
17.40
+0.050
-0.080

450
495.3
+1.27
-2.03

18
19.50
+0.050
-0.080

500
548.6
+1.27
-2.03

20
21.60
+0.050
-0.080

600
655.3
+1.27
-2.03

24
25.80
+0.050
-0.080

130
Copyright 2011 Shurjoint

Connect with the Best!

Gasket Seat A
Rigid
Flex.
+0/-0.51
+0.41/-1.19
+0/-0.02
+0.016/-0.047
mm / in
mm / in
21.34
19.05
0.840
0.750
21.34
19.05
0.840
0.750
21.34
19.05
0.840
0.750
24.13
22.23
0.950
0.875
25.78
23.83
1.015
0.938
25.78
23.83
1.015
0.938
25.78
23.83
1.015
0.938
34.04
30.18
1.340
1.188
34.04
30.18
1.340
1.188
34.04
30.18
1.340
1.188
34.04
30.18
1.340
1.188

Groove
Groove Dia. C
Width B
Tol.
+0.79/-0.41
+0
Radius
+0.031/-0.016
Basic
+0
R
mm / in
mm / in
mm / in
mm / in
9.53
94.56
-0.51
3.05
0.375
3.723
-0.020
0.120
9.53
115.90
-0.51
3.05
0.375
4.563
-0.020
0.120
9.53
169.06
-0.51
3.05
0.375
6.656
-0.020
0.120
12.70
223.04
-0.64
3.68
0.500
8.781
-0.025
0.145
12.70
274.65
-0.64
3.68
0.500
10.813
-0.025
0.145
12.70
327.81
-0.76
3.68
0.500
12.906
-0.030
0.145
15.88
327.81
-0.76
4.19
0.625
14.969
-0.030
0.165
15.88
433.40
-0.76
4.19
0.625
17.063
-0.030
0.165
15.88
485.78
-0.76
4.70
0.625
19.125
-0.030
0.185
15.88
538.96
-0.76
4.70
0.625
21.219
-0.030
0.185
15.88
645.31
-0.76
4.70
0.625
25.046
-0.030
0.185

www.shurjoint.com

Min.
Allow
Wall
Thick T
mm / in
7.9
0.31
8.1
0.32
8.6
0.34
9.1
0.36
9.7
0.38
10.2
0.40
10.7
0.42
10.9
0.43
11.2
0.44
11.4
0.45
11.9
0.47

Catalog 2011

MODEL

A505 Coupling
Shurjoint Model A505 couplings are

The Model A505 coupling is recommended

designed for connecting grooved ductile

for service up to 500 psi (35 bar) depending

iron pipe and fittings of ANSI/AWWA C151/

on the size. The GapSeal gasket fits flush

A21.51, Class 53 or higher dimensions.

over the pipe ends and prevents fluids from

The same coupling can be used either

entering into the gasket cavity.

as a flexible coupling or a rigid coupling


depending on the type of groove processed.

Nominal
Size
mm / in
80
3
100
4
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24

Pipe
O. D.
mm / in
100.6
3.96
121.9
4.80
175.3
6.90
229.9
9.05
281.9
11.10
335.3
13.20
388.6
15.30
442.0
17.40
495.3
19.50
548.6
21.60
655.3
25.80

Max. Working
Max. End
Pressure Load
Bar / PSI
kN / Lbs
35
27.59
500
6200
35
40.50
500
9000
28
66.26
400
14950
28
113.92
400
25600
25
150.63
350
33850
25
211.50
350
47900
17
204.47
250
45950
17
264.33
250
59400
17
332.19
250
74650
10
244.31
150
54900
10
348.80
150
78400

Axial
Bolts
Displacement*
size
A
mm / in
No.
in
mm / in
0~2.4

141
2
x3
0~0.09
5.55
0~2.4

164
2
x 3
0~0.09
6.46
0~2.4

218
2
x 3
0~0.09
8.58
0~4.0

275
2
x 4
0~0.16
10.83
0~4.0

332
2
x 4
0~0.16
13.07
0~4.0

390
2
x 6
0~0.16
15.35
0~4.0

441
4
1 x 3
0~0.16
17.36
0~6.4

504
4
1 x 3
0~0.25
19.84
0~6.4

560
4
1 x 3
0~0.25
22.05
0~6.4

610
4
1 x 4
0~0.25
24.37
0~6.4

740
4
1 x 4
0~0.25
29.14

Dimensions
B
mm / in
194
7.64
221
8.70
265
10.43
354
13.94
406
16.00
480
18.90
530
20.87
604
22.78
660
26.00
720
28.35
840
33.07

C
mm / in
56
2.20
57
2.25
57
2.25
67
2.64
70
2.76
70
2.76
73
2.88
89
3.50
89
3.50
89
3.50
89
3.50

Weight
Kgs / Lbs
2.5
5.5
3.3
7.3
4.4
9.7
8.5
18.7
11.0
24.2
14.0
30.8
16.0
35.2
26.4
58.0
35.0
77.0
38.0
83.6
49.0
107.8

Pressure ratings listed are based on radius cut-grooved Thickness Class 53 or higher pipe.
*only when connected on flexible radius groove.

Special gaaskets for AWWA ductile iron pipe


Grade

Temp. Range

-20F to
+ 180F
(-29C to
+82C)

Compound

Color Code

General Service Recommendations

Specially formulated to seal on ductile iron pipe iron

surfaces. Recommended for petroleum products, air


with oil vapors, vegetable and mineral oils within the

Nitrile

specified temperature range; except hot dry air over


60C (+140F) and water over 65C (+150F)

Red Stripe

NOT RECOMMENDED FOR HOT WATER SERVICES.


Specially formulated to seal on ductile iron pipe

-20F to
+ 200F
(-29C to
+93C)

-30F to
+ 350F
(-34C to
+177C)

surfaces. Recommended for water service plus a variety


of dilute acids, oil-free air and other chemical services

Halogenated
Butyl

within the specified temperature range. The compound

is UL classified per ANSI/NSF61 for potable water

Brown Stripe

applications.

NOT RECOMMENDED FOR HOT WATER SERVICES.

Recommended for dry heat, air without hydrocarbons to

Silicone

350F (177C) and certain chemical services.

Red Gasket

Connect with the Best!

www.shurjoint.com

131
Copyright 2011 Shurjoint

Catalog 2011

MODEL

A507 Transition Coupling


The Model A507 Transition Coupling
provides for a direct connection between
grooved end IPS steel pipe and grooved
end AWWA ductile iron pipe, fittings and
or valves. The A507 will accommodate roll
or cut grooved IPS steel pipe and rigid or
flexible AWWA ductile iron cut grooves.

Nominal
Size
mm / in
80
3
100
4
150
6
200
8
250
10
300
12

IPS Steel
mm / in
88.9
3.500
114.3
4.500
168.3
6.625
219.1
8.625
273.0
10.750
323.9
12.750

Pipe OD
AWWA Ductile Iron
mm / in
100.6
3.96
121.9
4.80
175.3
6.90
229.9
9.05
281.9
11.10
335.3
13.20

Max. Working
Max. End
Pressure Load
Bar / PSI
kN / Lbs
35
21.41
500
4810
35
35.38
500
7950
28
61.32
400
13780
28
103.99
400
23370
25
155.96
350
33850
25
220.64
350
47870

Axial
Bolts
Displacement
size
A
mm / in
in
mm / in
1

140
x 2
0.03
5.50
1

162
x 3
0.03
6.38
1

214
x 3
0.03
8.44
1

279
x 4
0.03
11.00
1

334
x 6
0.03
13.13
1

391
x 6
0.03
15.38

Dimensions
B
mm / in
187
7.38
229
9.00
283
11.13
353
13.88
419
16.50
481
18.94

C
mm / in
53
2.07
56
2.19
59
2.31
67
2.63
67
2.63
67
2.63

Weight
Kgs / Lbs
2.2
4.8
2.9
6.4
3.9
8.6
7.6
16.7
11.3
24.9
13.0
28.6

MODEL

A512 Flange Adapter


The Model A512 Flange Adapter provides
for the direct connection between AWWA
ductile iron radius pipe grooves and flanged

components. The two part flange features


integral closure tabs to aid in assembly.
Note: As with other flange adapters the

A512 requires a sufficient smooth flat mating


area for proper sealing, please reference

the A512 cut sheet or contact Shurjoint for


details.

AWWA D. I. Pipe
Nominal Size
Pipe OD

mm / in
mm / in

80
100.6

3
3.96

100
121.9

4
4.80

150
175.3

6
6.90

200
229.9

8
9.05

250
281.9

10
11.10

300
335.3

12
13.20

Max. Working
Max. End
Bolts
Pressure Load

size
A
Bar / PSI
kN / Lbs
No.
in
mm / in
17
13.80

191
4
x3
250
3100
7.50
17
20.03

229
8
x3
250
4500
9.00
17
41.39

279
8
x 3
250
9300
11.00
17
71.20

343
8
x 3
250
16000
13.50
17
105.47
406
12
x4
250
23700
16.00
17
151.30

483
12
7/8 x 4
250
34000
19.00

Dimensions
B
mm / in
152
6.00
191
7.50
241
9.49
298
11.75
362
14.25
432
17.00

Flange drilling to ANSI B16.1 Class 125.

132
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

C
mm / in
24
0.94
24
0.94
25
1.00
29
1.13
30
1.19
32
1.25

Weight
Kgs / Lbs
3.9
8.6
4.5
9.9
5.4
12.0
8.6
18.9
11.5
25.3
15.6
34.4

AWWA GROOVED FITTINGS

Catalog 2011

MODEL

A10 90 ELBOW A11 45 ELBOW A12 22 ELBOW


A13 11 ELBOW A60 CAP
Shurjoint AWWA grooved end fittings are

C-110 for wall thickness. Pressure ratings

supplied with rigid radius grooves as per

are 500 psi (35 Bar). Fittings are supplied

ANSI / AWWA C-606. The fittings also

painted black. Other surface finish options

conform to ANSI A21.10 / AWWA C-110

including 'non-coated' and cement/mortar

for center to end (C to E) dimensions and

lining Type II are available on request.

AWWA C-153 or ANSI A21.10 / AWWA

E-E

C-E

E-E


AWWA

D. I. Pipe
Nom. Size
OD
mm / in
mm / in

80
100.6

3
3.96

100
121.9

4
4.80

150
175.3

6
6.90

200
229.9

8
9.05

250
281.9

10
11.10

300
335.3

12
13.20

C-E

A10
90 Elbow

A11
45 Elbow

A10
90 Elbow
C - E
Weight
mm / in
Kgs / Lbs
140
4.2
5.50
9.2
165
5.6
6.50
12.2
203
10.7
8.00
23.5
229
18.9
9.00
41.6
279
29.5
11.00
64.0
305
42.8
12.00
94.2

A11
45 Elbow
C - E
Weight
mm / in
Kgs / Lbs
76
2.6
3.00
5.8
102
4.2
4.00
9.2
127
8.0
5.00
17.6
140
15.0
5.50
33.0
165
20.4
6.50
44.9
191
32.7
7.50
72.0

Connect with the Best!

C-E
A12
22 Elbow
A12
22 Elbow
C - E
Weight
mm / in
Kgs / Lbs
76
5.7
3.00
12.5
102
5.2
4.00
11.5
127
11.3
5.00
25.0
140
17.9
5.50
39.5
165
30.4
6.50
67.0
191
49.0
7.50
108.0

C-E
A13
11 Elbow

4"-8" 10"-12"
A60 Cap

A13
11 Elbow
C - E
Weight
mm / in
Kgs / Lbs
76
4.1
3.00
9.0
102
5.2
4.00
11.5
127
9.8
5.00
21.5
140
17.7
5.50
39.0
165
34.9
6.50
77.0
191
54.0
7.50
120.0

A60
Cap

www.shurjoint.com

E - E
mm / in
29
1.16
29
1.16
29
1.16
34
1.34
39
1.53
39
1.53

Weight
Kgs / Lbs
1.2
2.6
1.6
3.5
3.1
6.8
5.9
13.0
10.0
22.0
11.2
24.6

133
Copyright 2011 Shurjoint

AWWA GROOVED FITTINGS

Catalog 2011

MODEL

A20 Tee


AWWA D. I. Pipe
Nom. Size
O. D.
mm / in
mm / in

80
100.6

3
3.96

100
121.9

4
4.80

150
175.3

6
6.90

200
229.9

8
9.05

250
281.9

10
11.10

300
335.3

12
13.20

C-E
C-E

A 20 Tee
C - E
Weight
mm / in
Kgs / Lbs
140
6.1
5.50
13.4
165
8.4
6.50
18.5
203
15.9
8.00
35.0
229
27.4
9.00
60.3
279
45.7
11.00
110.5
305
61.7
12.00
136.0

A20 Tee

MODEL

A25 Reducing Tee A50 Concentric Reducer A10R Reducing Elbow

C-E
C-E
C-E

E-E

A25 Reducing Tee

Nom. Size
mm / in
100 x 80
4 x 3
150 x 100
6 x 4
200 x 100
8 x 4
200 x 150
8 x 6
250 x 100
10 x 4
250 x 150
10 x 6
250 x 200
10 x 8
300 x 100
12 x 4
300 x 150
12 x 6
300 x 200
12 x 8
300 x 250
12 x 10

134
Copyright 2011 Shurjoint

AWWA
D. I. Pipe

OD
mm / in
121.9 x 100.6
4.80 x 3.96
175.3 x 121.9
6.90 x 4.80
229.9 x 121.9
9.05 x 4.80
229.9 x 175.3
9.05 x 6.90
281.9 x 121.9
11.10 x 4.80
281.9 x 175.3
11.10 x 6.90
281.9 x 229.9
11.10 x 9.05
335.3 x 121.9
13.20 x 4.80
335.3 x 175.3
13.20 x 6.90
335.3 x 229.9
13.20 x 9.05
335.3 x 281.9
13.20 x 11.10

A25
Reducing Tee

C - E
mm / in
165
6.50
203
8.00
229
9.00
229
9.00
279
11.00
279
11.00
279
11.00
305
12.00
305
12.00
305
12.00
305
12.00

Connect with the Best!

Weight
Kgs / Lbs
8.5
18.8
15.2
33.3
23.3
51.2
26.0
57.2
54.4
120.0
58.1
128.0
59.0
130.0
50.8
112.0
81.7
180.0
84.4
186.0
87.1
192.0

A50 Conc. Reducer

A50
Concentric Reducer
E - E
Weight
mm / in
Kgs / Lbs
178
3.5
7.00
7.7
229
6.5
9.00
14.3
279
10.9
11.00
23.9
279
12.6
11.00
27.7
305
19.1
12.00
42.0
305
20.9
12.00
46.0
305
18.8
12.00
41.3
356
27.2
14.00
60.0
356
31.8
14.00
70.0
356
33.6
14.00
74.0
356
38.1
14.00
84.0

A10R Reducing Elbow

A10R
90 Reducing Elbow
C - E
Weight
mm / in
Kgs / Lbs
165
5.5
6.50
12.1
203
11.4
8.00
25.1
229
19.8
9.00
43.6
229
19.0
9.00
41.8
---
-----
--279
34.9
11.00
77.0
279
39.9
11.00
88.0
---
-----
--305
49.9
12.00
110.0
305
57.2
12.00
126.0
305
68.0
12.00
150.0

www.shurjoint.com

Section 10
Technical Information
Pipe End Preparation............................................................................. 136
Roll Grooving Dimensions for IPS, BS & AS pipe.............................. 137
Roll Grooving Dimensions for ISO pipe.............................................. 138
Roll Grooving Dimensions for KS and JIS pipe.................................. 138
Cut Grooving Dimensions for IPS, BS, AS, ISO, JIS & KS pipe......... 139
Roll Grooving Machines Ratings and Capacity............................... 140
Typical Applications Flexible Couplings (General Applications)........... 142
Anchoring, Hanging and Supports....................................................... 144
Gasket Selection ................................................................................... 147
Chemical Resistance Information....................................................... 148
Fire Protection Services........................................................................ 151
Approved Pressure Ratings by UL and FM........................................ 152
Typical Applications Flexible Couplings Sprinkler Systems
(NFPA 13)........................................................................................... 154
Project Pictures...................................................................................... 156
Terms and Conditions............................................................................ 160

Catalog 2011

Catalog 2011

Pipe End Preparation


How to process roll-grooves

Shurjoint grooved piping systems require the


processing of a roll or cut groove to the pipe ends
being connected. The engagement of the housing
keys in the grooves is integral in providing a secure
and leak-tight joint. It is essential that the grooves are
properly processed for optimum joint performance.

applied on the ground surface. Shurjoint strongly recommends the


processing of cut-grooves on heavy or thick wall pipe.

No or very little protrusion


Thicker than 9.5mm (0.375)

Housing

Pipe

Key

Plain end pipe and beveled end pipe

While plain-end pipe is preferred, the use of beveled end pipe is


acceptable providing that the wall thickness is .375/9.5mm or thinner

Rubber gasket

and the bevel is 37 2 or 30 as specified in ANSI B16.25 and

Groove

Full engagement

Nominal pipe size

Plain-end

ASTM A-53 respectively.

Plain-end pipe

Shurjoint couplings and fittings are identified by the nominal IPS

37 or 30

pipe size in inches or nominal diameter of pipe (DN) in millimeters.


Always check the actual O.D. of the pipe and fittings to be connected,

Beveled-end Pipe
( ANSI B16.25 / ASTM A- 53 )

as in some markets it is customary to refer to different O.D. pipes with


the same nominal size.

ERW pipe

ERW pipe is one of the most popular types of pipe used today.

Roll groove profile

Depending on the individual pipe and manufacturer, welding beads

Roll grooves should be as defined


To achieve optimum
A as possible.
B

may remain on the surface (inside and outside) of the pipe. Always

When processing a roll groove the machine operator should manage

rattling of the roll grooving machine resulting in inaccurate grooves.

joint performance the K dimension should be as small as possible.


the feed pressure of the upper roll set so as to achieve the best

possible groove profile.

C
A
K

B
B1

remove harmful weld beads near the pipe ends as they can cause

Galvanized pipe

Galvanized pipe is acceptable as long as the gasket seating surface


is smooth and free from scale and imperfections that could affect
gasket sealing. Whenever you remove welding beads or projections
from the sealing surface of galvanized pipe, use caution so as to not

Applicable pipe wall thickness

Roll grooves are generally applicable to .375/9.5mm thick or


thinner wall carbon steel pipe, stainless steel pipe, copper tube,
aluminum pipe and PVC pipe depending on the type of roll-grooving
machine and roll set being used. Different wall thicknesses and sizes
require the use of different roll sets. Contact the roll groove machine
manufacturer for additional information.

over-grind the surface. After grinding, always apply a proper rustprevention coating to this area.

Spiral welded pipe

Spiral welded pipe may be used as long as the weld beads are
removed from the gasket seating surface. It is also acceptable and
recommended to weld a grooved end nipple to the pipe end as
shown below. Whenever you remove weld beads or projections from
the gasket seating surface, use caution so as to not over-grind the
surface. After grinding, always apply a proper rust-prevention coating
to this area.

Heavy wall pipe

Welded

When you attempt to roll-groove pipe thicker than .375/9.5mm, the


metal may deform and heap up on both sides of the groove rather
than radially deforming and protruding on the inside of the pipe.
The extra heaped metal could lead to joint failure. In such a case,
you should grind off any such extra metal to achieve a flat and
Spiral pipe

smooth sealing surface. A proper rust preventative coating must be

136
Copyright 2011 Shurjoint

Connect with the Best!

Weld beads
shall be removed
Spiral pipe with
a grooved nipple

www.shurjoint.com

Catalog 2011

Roll Grooving Dimensions for ANSI B36.10, BS 1387 (M) & AS-1074 (M) Pipe
t

A
B

Basic roll groove dimensions conform to ANSI/AWWA C606-06


Table 5 with slightly adjusted tolerances to incorporate international
standards including CSA B242, ISO/FDIS 6152-12, VdS 2100-6en

O.D.

and JPF MP-006.


Nominal

Size
Basic

mm / in
mm / in

20
26.7


1.050

25
33.4

1
1.315

32
42.2

1
1.660

40
48.3

1
1.900

50
60.3

2
2.375

65
73.0

2
2.875


76.1
76.1mm

3.000

80
88.9

3
3.500

90
101.6

3
4.000

100
114.3

4
4.500


139.7
139.7mm

5.500

125
141.3

5
5.563


165.1
165.1mm

6.500

150
168.3

6
6.625

200
219.1

8
8.625

250
273.0

10
10.750

300
323.9

12
12.750

350
355.6

14
14.000

400
406.4

16
16.000

450
457.2

18
18.000

500
508.0

20
20.000

550
559.0

22
22.000

600
609.6

24
24.000

Pipe O.D.

Tolerance
mm / in
mm / in
+0.25
-0.25
+0.010
-0.010
+0.33
-0.33
+0.013
-0.013
+0.41
-0.41
+0.016
-0.016
+0.48
-0.48
+0.019
-0.019
+0.61
-0.61
+0.024
-0.024
+0.74
-0.74
+0.029
-0.029
+0.76
-0.76
+0.030
-0.030
+0.89
-0.79
+0.035
-0.031
+1.02
-0.79
+0.040
-0.031
+1.02
-0.79
+0.040
-0.031
+1.40
-0.79
+0.050
-0.031
+1.42
-0.79
+0.056
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031

A
0.76 0.030
mm / in
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
19.05
0.750
19.05
0.750
19.05
0.750
23.83
0.938
23.83
0.938
25.40
1.000
25.40
1.000
25.40
1.000
25.40
1.000

B
0.76 0.030
mm / in
7.14
0.281
7.14
0.281
7.14
0.281
7.14
0.281
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
8.74
0.344
11.91
0.469
11.91
0.469
11.91
0.469
11.91
0.469
11.91
0.469
11.91
0.469
11.91
0.469
11.91
0.469
12.70
0.500

1. Pipe ends must be square cut. See table for maximum allowable tolerances from squareAcceptable max. pipe O.D.
cut ends.

PIPE

Pipe
Sizes

0.8mm ( 0.030 )

1.2mm ( 0.045 )

8 ~ above

1.6mm ( 0.060 )

Connect with the Best!

Groove
Depth d (ref.)
mm / in
1.42
0.056
1.60
0.063
1.60
0.063
1.60
0.063
1.60
0.063
1.98
0.078
1.93
0.075
1.98
0.076
2.11
0.083
2.11
0.083
2.11
0.083
2.11
0.083
2.16
0.085
2.16
0.085
2.34
0.092
2.39
0.094
2.77
0.109
2.77
0.109
2.77
0.109
2.77
0.109
2.77
0.109
4.37
0.132
4.37
0.172

Max. Allowed
Flare Dia.
mm / in
29.2
1.15
36.3
1.43
45.0
1.77
51.1
2.01
63.0
2.48
75.7
2.98
77.7
3.06
91.4
3.60
104.1
4.10
116.8
4.60
141.7
5.578
143.8
5.66
167.0
6.574
170.9
6.73
223.5
8.80
277.4
10.92
328.2
12.92
358.1
14.10
408.9
16.10
461.3
18.16
512.1
20.16
563.9
22.20
614.7
24.20

Housing segmen

Upper limit
Center line
Lower limit

Pipe O.D. check (Before grooving)

2. The gasket seating surface `A' shall be free from deep scores, marks, or ridges that would
prevent a positive seal.
3. The `C' dimensions are average values. The groove must be of uniform depth around the
entire circumference. Use a Shurjoint groove gage or rule to check the groove diameter.
4. The `t' is the minimum allowable wall thickness that may be roll-grooved.

Min. Wall
t
mm / in
1.65
0.065
1.65
0.065
1.65
0.065
1.65
0.065
1.65
0.065
2.11
0.083
2.30
0.090
2.11
0.083
2.11
0.083
2.11
0.083
2.90
0.114
2.77
0.109
2.90
0.114
2.77
0.109
2.77
0.109
3.40
0.134
3.96
0.156
3.96
0.156
4.19
0.165
4.19
0.165
4.78
0.188
4.78
0.188
4.78
0.188

Acceptance range

G (max)

Up to 3
4 ~ 6

C
+0.00 +0.000
mm / in
23.83-0.38
0.938-0.015
30.23-0.38
1.190-0.015
38.99-0.38
1.535-0.015
45.09-0.38
1.775-0.015
57.15-0.38
2.250-0.015
69.09-0.46
2.720-0.018
72.260-0.46
2.844-0.018
84.94-0.46
3.344-0.018
97.38-0.51
3.834-0.020
110.08-0.51
4.334-0.020
135.48-0.51
5.333-0.020
137.03-0.56
5.395-0.022
160.90-0.56
6.334-0.022
163.96-0.56
6.455-0.022
214.40-0.64
8.441-0.025
268.27-0.69
10.562-0.027
318.29-0.76
12.531-0.030
350.04-0.76
13.781-0.030
400.84-0.76
15.781-0.030
451.64-0.76
17.781-0.030
502.44-0.76
19.781-0.030
550.06-0.76
21.656-0.030
600.86-0.76
23.656-0.030

Groove Gage

Groove Rule

Quick check with a


housing segment

5. The `d' is for reference use only. The groove depth shall be determined by the groove
diameter `C'.
6. Flare Diameter: The pipe end that may flare when the groove is rolled shall be within this
limit when measured at the extreme end of the pipe.

www.shurjoint.com

137
Copyright 2011 Shurjoint

Catalog 2011

Roll Grooving Dimensions per ISO/FDIS 6182-12 Table 1

For ISO 4200:1991 Plain-end Steel Tubes, Welded and Seamless (Superseding BS1387 and DIN 2440 & DIN 2448)
A

B
t

F
C

OD

Figure 1 - Roll grooved-end dimensional reference points for Table 1


Dimensions in millimeters



Nominal

size


25

32

40

50

65

65

80

90

100

100

125

125

125

150

150

150

200

250

300

specificationsa

Pipe or tube
Outside diameter (OD)
Actual
Tolerance
size
33,7
+0,41 / -0,68
42,4
+0,50 / -0,60
48,3
+0,44 / -0,52
60,3
0,61
73,0
0,74
76,1
0,76
88,9
+0,89 / -0,79
101,6
+1,02 / -0,79
108,0
+1,07 / -0,70
114,3
+1,14 / -0,79
133,9
+1,32 / -0,70
139,7
+1,40 / -0,79
141,3
+1,42 / -0,79
159,0
+1,60 / -0,79
165,1
+1,60 / -0,79
168,3
+1,60 / -0,79
219,1
+1,60 / -0,79
277,4
+1,60 / -0,79
328,2
+1,60 / -0,79


Dimensional
Gasket seat
Gasket width
Grooved diameter C
A
B
Actual
Tolerance
0.76
0.76
size
15,88
7,14
30,23
0 / -0,38
15,88
7,14
38,99
0 / -0,38
15,88
7,14
45,09
0 / -0,38
15,88
8,74
57,15
0 / -0,38
15,88
8,74
69,09
0 / -0,46
15,88
8,74
72,26
0 / -0,46
15,88
8,74
84,94
0 / -0,46
15,88
8,74
97,38
0 / -0,51
15,88
8,74
103,73
0 / -0,51
15,88
8,74
110,08
0 / -0,51
15,88
8,74
129,13
0 / -0,51
15,88
8,74
135,48
0 / -0,51
15,88
8,74
137,03
0 / -0,56
15,88
8,74
154,50
0 / -0,56
15,88
8,74
160,90
0 / -0,56
15,88
8,74
163,96
0 / -0,56
19,05
11,91
214,40
0 / -0,64
19,05
11,91
268,28
0 / -0,69
19,05
11,91
318,29
0 / -0,76

Groove
depth
Db
1,70
1,70
1,60
1,60
1,98
1,93
1,98
2,11
2,11
2,11
1,93
2,11
2,13
2,20
2,16
2,16
2,34
2,39
2,77

Wall Thickness
T
Min. allow.
1,8
1,8
1,8
1,8
2,3
2,3
2,3
2,3
2,3
2,3
2,9
2,9
2,9
2,9
2,9
2,9
2,9
3,6
4,0

Flare F
Max.
Dia.
34,5
43,3
49,4
62,2
75,2
77,7
90,6
103,4
109,7
116,2
134,9
141,7
143,5
161,0
167,1
170,7
221,5
275,4
326,2

a See Figure 1 for dimensional diagram


b Dimension for reference only, groove diameter is determined by C.

Roll Grooving Dimensions for KS D3507 & JIS G3452 Carbon Steel Pipe
L

O.D.

C=G

A
mm
25A
32A
40A
50A
65A
80A
100A
125A
150A
200A
250A
300A

Nominal
size
Pipe
B
O.D.
mm
mm
1
34.0
1
42.7
1
48.6
2
60.5
2
76.3
3
89.1
4
114.3
5
139.8
6
165.2
8
216.3
10
267.4
12
318.5

Gasket
Seat L
+0.76*
mm
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
19.0
19.0
19.0

Groove Diameter:
Groove diameter G are only applicable to pipe sizes 150A or smaller. Grooves for 200A thru 300A are to be
determined by the groove circumference.
Groove Depth:
The d is for reference use only.
Flare Diameter:
The maximum flare diameters (f) are target values.

Groove
Groove Dia. G
Width W
Basic
Tolerance
+0.76*
+0.00*
mm
mm
mm
7.1
30.4
-0.38
7.1
39.1
-0.38
7.1
45.0
-0.38
8.7
56.9
-0.38
8.7
72.2
-0.46
8.7
84.9
-0.46
8.7
110.1
-0.51
8.7
135.5
-0.56
8.7
160.8
-0.56
11.9
211.6
-0.64
11.9
262.6
-0.69
11.9
312.9
-0.76

Groove
Circumference
C
mm
mm
95.5
0 / -3.1
122.8
0 / -3.1
141.4
0 / -3.1
178.8
0 / -3.1
226.8
0 / -3.1
266.7
0 / -3.1
345.9
0 / -3.1
425.7
0 / 3.1
505.2
0 / -3.1
664.8
0 / -3.1
825.0
0 / -3.1
983.0
0 / -3.1

The tolerance for the JIS & KS pipe has a little difference.

138
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Groove
Depth
d (ref)
mm
1.80
1.80
1.80
1.80
2.05
2.10
2.10
2.15
2.20
2.35
2.40
2.80

Flare
f
mm
35.5
44.2
50.1
62.0
77.8
90.6
116.8
142.3
167.7
219.8
270.9
322.0

Catalog 2011

Cut Grooving Dimensions for IPS, BS, AS, ISO, JIS & KS Pipe
A

t
B

O.D.


Nominal

Size
Basic

mm / in
mm / in

20
26.7


1.050

25
33.4

1
1.315

32
42.2

1
1.660

40
48.3

1
1.900

50
60.3

2
2.375

65
73.0

2
2.875


76.1
76.1mm

3.000

80
88.9

3
3.500


101.6
101.6mm

4.000


108.0
108.0mm

4.250

100
114.3

4
4.500

125
141.3

5
5.563


133.0
133.0mm

5.250


139.7
139.7mm

5.500


159.0
159.0mm

6.250


165.1
165.1mm

6.500

150
168.3

6
6.625

200
219.1

8
8.625

250
273.0

10
10.750

300
323.9

12
12.750


216.3
200 JIS

8.516


267.4
250 JIS

10.528


318.5
300 JIS

12.539

350
355.6

14
14.000

400
406.4

16
16.000

450
457.2

18
18.000

500
508.0

20
20.000

550
558.8

22
22.000

600
609.6

24
24.000

Gasket Seating Surface (Column 3):


The gasket seating surface shall be free from deep scores, marks, or ridges that could prevent a positive seal.
Groove Width (Column 4):
Groove width is to be measured between vertical flanks of the groove side walls.
Groove Diameter (Column 5):
The 'C' diameters are average values. The groove must be of uniform depth around the entire pipe circumference.
Minimum Wall Thickness (Column 6):
The 't' is the minimum allowable wall thickness that may be cut-grooved.
Groove Depth (Column 7):
The 'd' is for reference use only. The groove dimension shall be determined by the groove diameter 'C'.

Pipe O. D.
Tolerance
mm / in
mm / in
+0.25
-0.25
+0.010
-0.010
+0.33
-0.33
+0.013
-0.013
+0.41
-0.41
+0.016
-0.016
+0.48
-0.48
+0.019
-0.019
+0.61
-0.61
+0.024
-0.024
+0.74
-0.74
+0.029
-0.029
+0.76
-0.76
+0.030
-0.030
+0.89
-0.79
+0.035
-0.031
+1.02
-0.79
+0.040
-0.031
+1.04
-0.79
+0.043
-0.031
+1.14
-0.79
+0.045
-0.031
+1.42
-0.79
+0.056
-0.031
+1.70
-0.79
+0.053
-0.031
+1.42
-0.79
+0.056
-0.031
+1.60
-0.79
+0.063
-0.031
+1.57
-0.79
+0.065
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031
+1.60
-0.79
+0.063
-0.031

A
0.79
0.031
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
15.88
0.625
19.05
0.750
19.05
0.750
19.05
0.750
19.05
0.750
19.05
0.750
19.05
0.750
23.83
0.938
23.83
0.938
25.40
1.000
25.40
1.000
25.40
1.000
25.40
1.000

B
0.79
0.031
7.95
0.313
7.95
0.313
7.95
0.313
7.95
0.313
7.95
0.313
7.95
0.313
7.95
0.313
7.95
0.313
7.95
0.313
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
9.53
0.375
11.13
0.438
12.70
0.500
12.70
0.500
11.13
0.438
12.70
0.500
12.70
0.500
12.70
0.500
12.70
0.500
12.70
0.500
12.70
0.500
14.30
0.563
14.30
0.563

C
0.00
0.000
23.83-0.38
0.938-0.015
30.23-0.38
1.190-0.015
38.99-0.38
1.535-0.015
45.09-0.38
1.775-0.015
57.15-0.38
2.250-0.015
69.09-0.38
2.720-0.018
72.26-0.46
2.845-0.018
84.94-0.46
3.344-0.018
97.38-0.51
3.834-0.020
103.73-0.51
4.084-0.020
110.08-0.51
4.334-0.020
137.03-0.56
5.395-0.022
129.13-0.51
5.084-0.020
135.48-0.51
5.334-0.020
154.43-0.76
6.080-0.030
160.90-0.56
6.335-0.022
163.96-0.56
6.455-0.022
214.40-0.64
8.441-0.025
268.27-0.69
10.562-0.027
318.29-0.76
12.531-0.030
211.60-0.64
8.331-0.025
262.60-0.69
10.339-0.027
312.90-0.76
12.319-0.030
350.04-0.76
13.781-0.030
400.84-0.76
15.781-0.030
451.64-0.76
17.781-0.030
502.44-0.76
19.781-0.030
550.06-0.76
21.656-0.030
600.86-0.76
23.656-0.030

Connect with the Best!

Min. Wall
t
mm / in
2.87
0.113
3.38
0.133
3.56
0.140
3.68
0.145
3.91
0.154
4.78
0.188
4.78
0.188
4.78
0.188
4.78
0.188
5.16
0.203
5.16
0.203
5.16
0.203
5.16
0.203
5.16
0.203
5.56
0.219
5.16
0.203
5.56
0.219
6.05
0.238
6.35
0.250
7.09
0.279
6.05
0.238
6.35
0.250
7.09
0.279
7.14
0.281
7.92
0.312
7.92
0.312
7.92
0.312
9.53
0.375
9.53
0.375

www.shurjoint.com

7
Groove Depth
d (ref.)
mm / in
1.42
0.056
1.60
0.063
1.60
0.063
1.60
0.063
1.60
0.063
1.98
0.078
1.98
0.078
1.98
0.078
1.98
0.078
2.11
0.083
2.11
0.083
2.11
0.083
1.93
0.076
2.11
0.083
2.20
0.087
2.16
0.085
2.16
0.085
2.34
0.092
2.39
0.094
2.77
0.109
2.34
0.092
2.39
0.094
2.77
0.109
2.77
0.109
2.77
0.109
2.77
0.109
2.77
0.109
4.37
0.172
4.37
0.172

139
Copyright 2011 Shurjoint

Catalog 2011

Roll Grooving Machines and Tools Ratings & Capacity


Tool Model
Pipe
Pipe
Pipe size
No.
Material
Schedule
Range


SHURJOINT
Carbon Steel
Sch. 10
1" - 12"
Sch. 40, STD
1" - 6"
DSC-002




Stainless
Sch. 10S
1" - 10"








Roll
Set

(Standard) 2" - 6" Upper roll, Sch. 10 & Sch. 40 (STD)


(Standard) 2" - 3" Bottom roll, Sch. 10 & Sch. 40 (STD)
(Standard) 4" - 6" Bottom roll, Sch. 10 & Sch. 40 (STD)
(Standard) 8" - 12" Upper & bottom rolls, Sch. 10
(Optional) 1" - 1 1/2" Upper roll, Sch. 40 (STD)
(Optional) 1" - Bottom roll, Sch. 40 (STD)
(Optional) 1 1/4" - 1 1/2" Bottom roll, Sch. 40 (STD)
(Optional) 2" - 6" Upper roll, Sch. 10S Stainless
(Optional) 2" - 3" Bottom roll, Sch. 10S Stainless
(Optional) 4" - 6" Bottom roll, Sch. 10S Stainless
(Optional) 8" - 10" Upper & bottom rolls, Sch. 10S Stainless

SHURJOINT
Carbon Steel
Sch. 10
8 ~ 24
.375" wall (STD)
8" - 24"
DSC-003


Stainless
Sch. 10S
8" - 24"






(Standard) 8" - 12" Upper & bottom rolls, Sch. 10 & STD
(Standard) 14" - 16" Upper & bottom rolls, Sch. 10 & STD
(Standard) 18" - 20" Upper & bottom rolls, Sch. 10 & STD
(Standard) 22" - 24" Upper & bottom rolls, Sch. 10 & STD


Carbon Steel
RG-150A

(Standard) 2" - 6" Sch. 10 & Sch. 40 steel

Sch. 10
1 ~ 16
Sch. 40
1 ~ 12
(w/ automatic pump)
Stainless
Sch. 5S & 10S
RG-150
(w/ hand pump)

.375 wall
1" - 6"




(Optional) 8" - 12" Upper & bottom rolls, Sch. 40


(Optional) 14" - 16" Upper & bottom rolls, Sch. 40
(Optional) 8" - 12" Upper & bottom rolls, Sch. 10S Stainless
(Optional) 14" - 16" Upper & bottom rolls, Sch. 10S Stainless
(Optional) 18" - 20" Upper & bottom rolls, Sch. 10S Stainless
(Optional) 22" - 24" Upper & bottom rolls, Sch. 10S Stainless

(Optional) 8" Sch. 10 & 40, 10" - 12" Sch. 10 steel


(Optional) 1 " - 1 1/2" Sch. 10 & 40 steel
(Optional) 10" - 12" Sch. 40 & STD steel
(Optional) 14" - 16" Sch. 10 steel
(Optional) 2 " - 3" Sch. 5S & 10S stainless
(Optional) 3 " - 6" Sch. 5S & 10S stainless



Carbon Steel
Sch. 10
1 ~ 16
(Standard) 2" - 6" Sch. 10 & Sch. 40 steel
RG-RH
Sch. 40
1 ~ 12

(Optional) 8" Sch. 10 & 40, 10" - 12" Sch. 10 steel

Stainless
Sch. 5S &10S

(Optional) 1 " - 1 1/2" Sch. 10 & 40 steel

.134"(3.4mm) wall 1" - 6"
(Optional) 10" - 12" Sch. 40 & STD steel

(Optional) 14" - 16" Sch. 10 steel

(Optional) 1 " - 1 1/2" Sch. 5S & 10S stainless

(Optional) 2 " - 3" Sch. 5S & 10S stainless

(Optional) 3 " - 6" Sch. 5S & 10S stainless


(to use with Rex 2-4" pipe machine or Ridgid #300 driver)



Carbon Steel
Sch. 10
1 ~ 6
(Standard) 2" - 3" Sch. 10 & 40 steel
RG-R1, E1
Sch. 40
1 ~ 12
(Standard) 4" - 6" Sch. 10 steel

(Optional) 1 " Sch. 10 & 40 steel

(Optional) 1 1/2" Sch. 10 & 40 steel


(to use with Rex 2-4" pipe machine or Ridgid #300 driver)
Please contact Rex Industries Co., Ltd. www.rexind.co.jp for updated information on roll sets. For other roll grooving machines, always refer to the installation instructions of the machine
and roll set you are going to use before operating.

140
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

Roll Grooving Machines and Tools Ratings & Capacity


Tool Model
Pipe
No.
Material

Pipe
Schedule

Pipe size
Range

Roll
Set


Steel

915

Stainless



PVC

Copper

Sch. 10
Sch. 40
Sch. 10
Sch. 40
Sch. 40
Sch. 80
K, L, M, DWV

1" 12"
1" 6"
1" 12"
1" 6"
1" 6"
1" 3"
2" 8"

(Standard) 2" 6" Sch. 10 (2"-3" Sch. 40) steel, stainless,


PVC
(Optional) 1" 1" Sch. 10, 40 steel, stainless, PVC
(Optional) 4" 6" Sch. 40 steel, stainless, PVC
(Optional) 8" 12" Sch. 10 steel, stainless, PVC

Sch. 40
Sch. 80
K, L, M, DWV

1" 6"
1" 6"
2" 6"

(Standard) 1" 6" Sch. 10, 40 steel


(Optional) 1" Sch. 10, 40 steel
(Optional) 2" 6" copper tube K, L, M & DWV


Steel
916


Stainless



PVC


Copper

Sch. 10
Sch. 40
Sch. 10
Sch. 40
Sch. 10
Sch. 40
K, L, M. DWV

1" 6"
1" 3"
1" 6"
1" 3"
1" 6"
1" 3"
2" 6"

(Standard) 1" 6" Sch. 10, 40 steel


(Optional) 1" Sch. 10, 40 steel


Steel
918


Stainless



PVC


Copper

Sch. 10
Sch. 40
Sch. 10
Sch. 40
Sch. 40
Sch. 80
K, L, M. DWV

1" 12"
1" 8"
1" 12"
1" 2"
1" 8"
2" 6"
2" 6"

(Standard) 2" 6" Sch. 10, 40 steel, stainless, PVC


(Standard) 8" 12" Sch. 10 (8" Sch. 40) steel, stainless, PVC
(Optional) 1" 1" Sch. 10, 40 steel, stainless, PVC

Steel

PVC
Copper

Sch. 10
Sch. 40
Sch. 80
K, L, M. DWV

1" 12"
1" 8"
2" 6"
2" 6"

(Standard) 2" 6" Sch. 10, 40 steel, stainless, PVC


(Standard) 8" 12" Sch. 10 (8" Sch. 40) steel, stainless, PVC
(Optional) 1" 1" Sch. 10, 40 steel, stainless, PVC
(Optional) 2" 6" copper tube K, L, M & DWV

Steel

Sch. 10

1" 6"

(Standard) 1" 6" Sch. 10, 40 steel

Sch. 10
Sch. 40
Standard Wall
Sch. 10
Sch. 40
Standard Wall
K, L, M. DWV

2" 24"
2" 12"
14" 16"
2" 24"
2" 12"
14" 16"
2" 8"

(Standard) 2" 6" Sch. 10, 40 steel, stainless


(Standard) 8" 12" Sch. 10, 40 steel, stainless
(Standard) 14" 16" Standard wall (.375") steel, stainless
(Optional) 4"- 6" Sch. 40 steel, stainless
(Optional) 18"- 20" Sch. 10 steel, stainless
(Optional) 22"- 24" Sch. 10 steel, stainless
(Optional) 2"- 8" copper tube K, L, M & DWV


960

Steel

Copper

(Optional) 2" 8" copper tube K, L, M & DWV


918-1

(Optional) 2" 6" copper tube K, L, M & DWV

(Optional) 2" 6" copper tube K, L, M & DWV

920


Steel




Stainless



Copper

Please contact Ridgid Tool Company www.ridgid.com for updated information on roll sets. For other roll grooving machines, always refer to the installation instructions of the machine
and roll set you are going to use before operating.

Connect with the Best!

www.shurjoint.com

141
Copyright 2011 Shurjoint

Catalog 2011

Typical Applications - Flexible


Couplings

3. Absorption of distortion

With the use of an assembly as shown below, ground sinking or


movement around a tank or reservoir can be effectively absorbed,

- General Systems -

avoiding damage to the tank, reservoir and or the piping system.

1. Absorption of vibration and noise

When a pump operates with frequent starts and stops, the piping
system is affected by the noise and vibration of the equipment. The
entire system may develop a large sway, referred to as sympathetic
vibration, as a result of the frequent cycling. Shurjoint flexible
couplings will help reduce such vibration and noise. The system
should always be properly designed with steel angle sway braces to
protect the system from large sways.

4. Absorption of inter-floor deflection

Risers of high-rise flexible structure buildings are subjected to lateral


sways (inter-floor deflection) when an earthquake occurs. If we
assume the inter-floor deflection is 1/150 and the floor height (H) as 4
meters, the estimated inter-floor deflection () will be;

Rigid coupling

Flexible coupling

= H 1/150

2. Adjustment of misalignment

When a straight run has need for a slight adjustment of alignment on


the jobsite as shown in the diagram, you can accomplish this with the
use of two flexible couplings. The following table shows the deflection
value () of the Shurjoint 7705 flexible couplings.

LL
== LL sin
sin

Hanger
Hanger location
location

= H x 1/150 = 4000 x 1/150 = 27mm


If we use a 200mm (8) 7707 coupling for each floor, the maximum

Nominal

deflection () that each coupling can accommodate will be;

Amount of deflection ()

Deflection Distance between couplings (L) mm

= L x tan = 4000 x 0.02915 = 4.56 = 116mm ( = 1.67)

Size

Angle()

600

1200

1500

2000

3000

2" / 50

3 02'

32

64

79

106

159

2 1/2" / 65

2 30'

26

52

65

87

131

3" / 80

2 04'

22

43

54

72

108

4" / 100

3 12'

34

67

84

112

168

5" / 125

2 36'

27

54

68

91

136

6" / 150

1 10'

12

24

31

41

61

8" / 200

1 40'

17

35

44

58

87

As shown in the diagram, each branch connection to the free riser

10" / 250

1 20'

14

28

35

47

70

12" / 300

1 08'

12

24

30

40

59

will be subjected to serious shearing forces as pressure thrusts or

The example shows a flexible coupling would be sufficient to absorb


this scale of seismic sways.

5. Absorption of misalignment

thermal movement increases. By using two flexible couplings, you


can solve this problem.

142
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

As the linear expansion coefficient for steel () is 1.2 x 10 , you can


-5

use the table above to determine the thermal expansion.


Example:
Expand

Pipe size: 100mm (4)


Max. pipe end separation (E) : 3.2mm

Hanger location

Pipe length (L) : 5.5 m


Temperature difference (T) : 40 C (+5 C to +45 C)

6. Curved layout

With Shurjoint flexible couplings you can design a slowly curved


layout for a system along a curved tunnel, winding road or curved
building.

= x L x T = 1.2 x 10-5 x 5500 x 40 = 2.64mm


The thermal expansion of a 5.5 meter standard length of pipe ()
is within the allowance (= max. pipe end separation) of a flexible
coupling. In other words, if you use a coupling for each pipe length of

R = (2 x tan /2) (where: R is radius of curvature, L is pipe length,


and is max. allowed deflection of a coupling)

5.5 meters, the coupling will accommodate the thermal expansion or


contraction expected to take place for a 40 C temperature change.
When you calculate the necessary number of couplings (N) for an
anchored system, you should place a clearance of N x E x as a

safety factor.
R

Whether it is thermal expansion, contraction, or a combination


thereof, the system requires suitable anchor installations with
properly space alignment guides and weight support devices. Where
and when larger thermal movement is anticipated, you should use

Example: When using model 7705 100mm (4) couplings for the
layout as shown in the diagram, the max. allowed deflection () of the
coupling is 3.4, and the pipe length (L) is 5.5 meters, the radius of
curvature (R) will be 92.7 meters.

supplementary expansion joint(s).


For installers who use the imperial units of measure, the following
table will be more convenient.

7. Absorption of Thermal Stress

Thermal stress is caused by changes in temperature, resulting in


either expansion or contraction. With the use of Shurjoint flexible
couplings you can design your system to accommodate such
movement without the need for costly expansion joints. The thermal
expansion or contraction () is determined by the length of pipe (L)
and temperature difference (T).
= x L x T

Thermal Expansion (Metric)

Temperature Pipe Length L (meters)


Difference

5.5*

10

20

30

40


T
Thermal Expansion (millimeters)
(C)

0.012

0.07

0.12

0.24

0.36

0.48

0.06

0.33

0.6

1.2

1.8

2.4

10

0.12

0.66

1.2

2.4

3.6

4.8

20

0.24

1.3

2.4

4.8

7.2

9.6

30

0.36

3.6

7.2

11

15

40

0.48

2.6

4.8

9.6

14

20

50

0.6

3.3

12

18

24

60

0.72

7.2

14

22

29

70

0.84

4.6

8.4

17

25

34

80

0.96

5.3

9.6

19

29

39

Thermal Expansion (Imperial)

Pipe Lenght L (feet)


Temperature

20

40

60

100


(F) Thermal Expansion between 70 F
and indicated temperature (inch)

-0.10

-0.20

-0.29

-0.49

25

-0.06

-0.13

-0.19

-0.32

50

-0.03

-0.06

-0.08

-0.14

70

100

0.05

0.09

0.14

0.23

125

0.08

0.17

0.25

0.42

150

0.12

0.24

0.37

0.61

175

0.16

0.32

0.48

0.80

200

0.20

0.40

0.59

0.99

225

0.24

0.48

0.73

1.21

* Coefficient of thermal expansion of steel pipe = 6.33 in/in, F x 10-6

* 5.5 meters is the standard length of commercial carbon steel pipe.

Connect with the Best!

www.shurjoint.com

143
Copyright 2011 Shurjoint

Catalog 2011

Anchoring, Hanging and Supports


Shurjoint grooved couplings are designed to hold axial thrusts 45
times their rated working pressure, though the strength against
bending movements is less than that of steel pipe. The joint may
be damaged when a bending movement greater than the allowed
deflection occurs. System designers should provide anchors (main

Hangers for straight runs

For straight runs, you can use both flexible and rigid couplings.
When rigid couplings are used, the same hanger spacing as other
piping methods can be applied. You can refer to the hanger spacing
standards of ANSI B31.1 Power Piping Code, B31.9 Building Services

Piping Code, NFPA 13 Sprinkler Systems, or Mechanical Equipment


Construction Guide (Japan). See the table below.

and intermediate) and pipe guides with proper spacing to protect the
system from unexpected large bending movements.

Suggested Max. Span between Supports


(steel pipe)

These illustrations are examples only, and are not intended to be


used for all installations as conditions and requirements vary from job
to job. Reliance on general data or information contained herein shall
be at the users sole risk and without obligation to Shurjoint.

Hangers shall be designed to support five times the weight of waterfilled pipe plus 250 lb (115 kgs) at each point of pipe support (NFPA
13 9.1.1.1.). The following illustrations are examples of acceptable
hanger types and sizes per NFPA 13.

D
dimension

U-Hook sizes
Pipe size

in

D dimension
in / mm

~ 2

2 ~ 6

(9.5)

(12.7)

5/16

(7.9)

Wraparound
U-hook

D
dimension
Rod sizes
Pipe size

in

D dimension
in / mm

Nominal Water Service Gas or Air Service


Pipe Size (feet / meters)

(feet / meters)

in/mm

1)

2)

3)

4)

1)

2)

3)

1 / 25

7 / 2.1

9 / 2.7

12 / 3.7

6.6 / 2.0

9 / 2.7

9 / 2.7

9 / 2.7

1 / 32

7 / 2.1

11 / 3.4

12 / 3.7

6.6 / 2.0

9 / 2.7

9 / 2.7

11 / 3.4

1 / 40

7 / 2.1

12 / 3.7

15 / 4.6

6.6 / 2.0

9 / 2.7

9 / 2.7

13 / 4.0

2 / 50

10 / 3.1

13 / 4.0

15 / 4.6

6.6 / 2.0

13 / 4.0

13 / 4.0

15 / 4.6

3 / 80

12 / 3.7

15 / 4.6

15 / 4.6

6.6 / 2.0

15 / 4.6

15 / 4.6

17 / 5.2

4 / 100

14 / 4.3

17 / 5.2

15 / 4.6

6.6 / 2.0

17 / 5.2

17 / 5.2

21 / 6.4

6 / 150

17 / 5.2

20 / 6.1

15 / 4.6

10 / 3.0

21 / 6.4

21 / 6.4

25 / 7.6

8 / 200

19 / 5.8

21 / 6.4

15 / 4.6

10 / 3.0

24 / 7.3

24 / 7.3

28 / 8.5

10 / 250

19 / 5.8

21 / 6.4

10 / 3.0

24 / 7.3

24 / 7.3

31 / 9.5

12 / 300

23 / 7.0

21 / 6.4

10 / 3.0

30 / 9.1

30 / 9.1

33 / 10.1

14 / 350

23 / 7.0

21 / 6.4

30 / 9.1

30 / 9.1

33 / 10.1

16 / 400

27 / 8.2

21 / 6.4

35 / 10.7 35 / 10.7 33 / 10.1

18 / 450

27 / 8.2

21 / 6.4

35 / 10.7 35 / 10.7 33 / 10.1

20 / 500

30 / 9.1

21 / 6.4

39 / 11.9

24 / 600

32 / 9.8

21 / 6.4

42 / 12.8 42 / 12.8 33 / 10.1

39 / 11.9

33 / 10.1

1) ANSI B31.1 Power Piping Code


2) ANSI B31.9 Building Services Piping Code
3) NFPA 13 Sprinkler systems
4) Ministry of Land & Transportation of Japan: Mechanical Equipment Construction Guide

Hanger locations on straight runs where flexible


couplings are used
When flexible couplings are used on straight runs, location of hangers

~ 4

(9.5)

shall be designed as close to each coupling as possible, or within a

5 ~ 8

(12.7)

10 ~ 12

(15.9)

distance of less than 1/6 the span.


Elevation

Adjustable swivel
Ring - rod tight
to pipe

max.1/6L
L
plan

D
dimension

Eye rod sizes


Pipe size

in

~ 4

5 ~ 6

10 ~ 12

144
Copyright 2011 Shurjoint

max.1/6L
D dimension
in / mm
(9.5)

L
Correct hanger location

(12.7)
(15.1)

Connect with the Best!

www.shurjoint.com

Wrong hanger location

00

mm

0
.50

ax

m
0m

ma

0
x.5

ma

0m

0
x.8

mm

00

m
0m
Ox.v30
ma er 6
00
m

0m

.30

x
ma

mm

.3
ax

Catalog 2011

Additional hangers or supports shall


provided
1-1/4"beand
above where runs are
1-1/4"
and above
curved, connected
to a branch
line or on short risers or drops.
Curved pipe runs
Short riser (or sh
Curved pipe runs

00

x.8

ma

Up to 1"

to 1"
andUpbranch

Hanger locations on curved pipe runs


lines

ma

x.5

ma

m
0m

.3
ax

Ov

er

60

0m

Up to 1"
1-1/4" and above

Up to 1"

Short riser (or short drop)


Short riser (or short drop)

Curved pipe runs


1-1/4" and above
m

0m

.80

Curved pipe runs

x
ma

m
0m

.30

ax

mm
00
x.3O
ve
r6

0m

.30

x
ma

mm

00

x.3

ma

ma

Ov

er

00

mm

60

0m

Ov

Ov

er

er

60

0m

60

Branch line

0m

1"
1-1/4" and above
Curved pipe runs
m

m
00

x.3

ma

m
00

Short riser (or short drop)


Short riser (or short drop)
Ov

er

Ov

er

60

60

0m
m
m
Typical designsO of hangers and
sway
Ov braces for
ve
er
r6
6
00
00
pipe runs
mm
mm
0m

Pipe runs shall be adequately suspended by rod hangers or steel

Branch line

Branch line

the movement of the piping. Hangers and their components shall be


ferrous. The maximum distance between hangers shall not exceed
that specified in the table of previous page.

angles that are directly attached to the building structure to restrict

Short riser (or short drop)

Ov

er

60

Inserts Inserts

Branch line

Ov

0m

Branch line

er

60Insert
0m
m

Insert

Hanger rod
Hanger rod
U-bolt

U-bolt

Band hanger
Band hanger

A rodfor
hanger
for a
single
A rod hanger
a single
pipe
run pipe run
Branch line
Inserts Inserts

A hanger
trapezesuspended
hanger suspended
from ceiling
A trapeze
from ceiling

U-bolt
Hanger rod
Hanger rod

U-bolt

U-bolt

U-bolt
Inserts Inserts

A hanger
trapezefor
hanger
for multiple
A trapeze
multiple
pipe runspipe runs
A steel
angle bracket
A steel angle
bracket
attachedattached
to wall to wall

Connect with the Best!

www.shurjoint.com

145
Copyright 2011 Shurjoint

Catalog 2011

Supports for risers

In multi-story buildings, risers shall be fixed (or anchored) at the


lowest level and at the top of the riser and shall be supported by

Anchors for risers (

riser clamps or U-bolts at each floor level to prevent the risers from
swaying. If risers are braced by the penetration floors, the number of
riser clamps or U-bolts may be reduced to one at each three stories.

weld

For risers, either flexible or rigid couplings

Resilient
Isolator

can be used as long as proper anchoring and


support is provided.
Riser clamp

Max.

14 F

U-bolt

1m

15 F

Sway brace (

Max.

1m

Sway braces for risers (

13 F

Sway brace (

Anchor ( Heat Insulator


)

Sway braces for risers (

Resilient
Isolator

3F

U-bolt
90 Elbow
w/Base Support

Resilient Isolator

2F

1F

Sway braces for risers (

Sway brace (

Sway brace (

Heat Insulator

Flexible Coupling
Rigid Coupling
Anchor

U-bolt
U-bolt

Sway brace

Anchors should be sufficient to hold the Sway


weightbrace
of water-filled
(
) pipe
and pressure thrusts.
Heat
Insulator
Pipe guides (sway braces) should be such as to
brace
lateral

movement of the system.


Resilient
Isolator

146
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Resilient
Isolator

Sway brace

Catalog 2011

Gasket Selection
Proper gasket selection is essential for the optimum
performance of Shurjoint grooved couplings, flange
adapters and mechanical tees.

6. Dry pipe and freezer services: Shurjoint recommends the use

1. Compound Grade: In general, Grade "E" EPDM gaskets are

between the pipes or gasket cavity. This will prevent any remaining

of GapSeal Grade "E" gaskets for dry pipe fire protection systems
and freezer applications. The GapSeal gasket closes off the gap

recommended for cold and hot water services, Grade "T" Nitrile (or

liquid from entering the cavities and freezing when the temperature

NBR) gaskets for oils, Grade "L" Silicone gaskets for hot air and

drops. Rigid couplings are preferred for dry pipe, freezer and

Grade "O" Fluorocarbon gaskets for fuels and harsh chemicals.

vacuum applications. Reducing couplings are not recommended for

Refer to pages 6 & 7 for further details. Failure to select the proper

these applications.

compound may cause a joint failure and or property damage.


2. Chemical resistance: The listing of chemical resistance

Do not use the Shurjoint standard lubricant for dry pipe

shows general service recommendations of Grades "E" (EPDM),


"T" (Nitrile), "L" (Silicone), "V" (Neoprene) and "O" (Fluorocarbon,

and freezer systems, instead use a petroleum free silicone based

Viton) gaskets for various chemicals used at ambient temperatures.

lubricant.

The data and recommendations presented are based on the best


information available today. For unusual and or severe services, or

services not listed please contact Shurjoint for a recommendation.

3. Service temperatures: In general, rubber compounds can not


maintain elasticity and sealing capabilities at temperatures below
-40F (-40C). Thus, recommended low temperature ranges of

7. ANSI/NSF 61 Standard: ANSI/NSF 61 classified gaskets are good

Shurjoint gaskets are -30 to -20F (-34 to -29C). Resistance

for potable water services. The classification categories are cold

against elevated temperatures varies depending on the grade of

which is limited to +86F (+30C) (or maximum ambient distribution

compound and media (air, water, steam or chemicals). See page 7

temperatures of unheated water) maximum and hot which is limited

for details.

to +180F (+82C) (or scalding temperatures of hot domestic water).

4. Gasket styles: Shurjoint grooved couplings utilize several

8. Lubricant: Shurjoint lubricant is recommended for proper gasket

different gasket styles, standard, GapSeal, EP (End Protection)

installation to prevent the gasket from being pinched. Apply a thin coat

and FF (Fast Fit). GapSeal gaskets are compatible with standard

to the gasket exterior, gasket lips and or housing interiors. Shurjoint

gaskets and they are interchangeable with each other. Other special

lubricant is available in one pound (450 grams) and one quart ( 2

styles are not compatible with standard or GapSeal gaskets. Always

pounds or 900 grams) containers. Certified to ANSI/NSF 61.

use the correct gasket style for the coupling model you selected.

Standard

GapSeal

End Protection

FastFit

5. Vacuum service: Shurjoint standard gaskets are designed to


seal well under vacuum conditions up to 10 inHg (absolute)/254
mmHg (absolute) which may occur when a system is drained. For
continuous services greater than 10 inHg (absolute)/254 mmHg
(absolute), the use of GapSeal gaskets or EP (end protection)
gaskets in combination with rigid style couplings is recommended.
Contact Shurjoint for specific recommendations.

Connect with the Best!

www.shurjoint.com

147
Copyright 2011 Shurjoint

Catalog 2011

Chemical Resistance
Number = Max. Recommended Temp. (F)
NR = Not Recommended
--- = Incomplete Data
Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Acetaldehyde

200

---

---

NR

NR

Aviation Fuel

NR

150

NR

NR

---

Acetamide

200

150

---

NR

120

Barium Carbonate

200

100

100

160

Acetic Acid, to 10%

180

100

180

NR

NR

Barium Chloride

200

150

100

Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Cellulube 220 (Tri-Aryl-Phosphate) 200

---

100

---

200

Cellulube Hydraulic Fluids

200

---

---

---

-----

160

200

China Wood Oil, Tung Oil

NR

150

---

---

---

Acetic Acid, 10 - 50%

140

---

100

NR

NR

Barium Hydroxide

180

150

NR

150

200

Chloralhydrate

NR

NR

NR

70

NR

Acetic Acid, Glacial

100

---

100

NR

NR

Barium Nitrate

200

100

---

160

200

Chloric Acid, to 20%

NR

---

---

140

140
185

Acetic Anhydride

100

100

---

70

NR

Barium Sulfide

140

150

NR

160

200

Chlorine Gas, Dry or Wet

NR

---

---

NR

Acetone

130

---

---

NR

NR

Beer

200

Gr. A

NR

140

200

Chloroacetone

200

NR

NR

---

---

Acetonitrile

NR

100

---

70

NR

Beet Sugar liquors

200

Gr. A

100

160

185

Chlorobenzene

NR

NR

NR

NR

70

Acetophenone

140

---

---

NR

NR

Benzaldehyde

140

NR

NR

NR

NR

Chlorobromomethane

NR

NR

NR

NR

NR

Acetyl Chloride

NR

---

---

NR

185

Benzene

NR

NR

NR

NR

150

Chloroform

NR

NR

NR

NR

70

Acetylene

200

150

100

70

200

Benzene Benzol

200

---

---

---

200

Chlorosulphonic Acid

NR

NR

NR

NR

NR

Acrylic Resin

NR

100

---

100

NR

Benzene Sulfonic Acid

NR

NR

NR

160

185

Chrome Alum

100

100

100

---

---

Acrylonitrile

NR

NR

NR

NR

NR

Benzine

NR

NR

NR

NR

150

Chromic Acid, to 10%

70

---

NR

NR

140

Adipic Acid, Saturated

200

150

---

200

200

Benzoic Acid (Saturated)

NR

---

NR

160

---

---

NR

160

200

Air, oil free

230

140

350

NR

300

Benzol

NR

NR

NR

NR

150

Citric Acid, Saturated

200

100

NR

140

200

Benzyl Alcohol

NR

NR

NR

NR

140

Coconut Oil

NR

Gr. A

NR

100

185

Benzyl Benzoate

140

NR

---

---

---

Cod Liver Oil

NR

Gr. A

100

---

---

Coke Oven Gas

70

150

100

---

185

Air with vapored oil


Alkalis
Allyl Alcohol

NR

150

---

NR

300

Good

NR

---

---

---

70

---

---

70

100

Black Liquor

180

---

---

70

200

Chromium Potassium Nitrate 140

Allyl Chloride

NR

NR

NR

NR

70

Black Sulfate Liquor

100

150

100

---

---

Copper Acetate, Saturated

100

---

NR

160

140

Aluminum Acetate

200

100

NR

NR

NR

Blast Furnance Gas

NR

150

100

---

---

Copper Carbonate

200

---

---

---

185

Aluminum Ammonium

200

---

---

160

200

Bleach, Industrial (15% Cl2)

70

---

---

---

185

Copper Chloride

200

150

100

160

200

Aluminum Chloride

200

150

NR

160

200

Borax

140

---

---

140

185

Copper Cyanide

200

150

100

160

185

Aluminum Chrome

200

---

---

160

200

Bordeaux Mixture

200

---

---

---

---

Copper Fluoride

200

100

---

140

185

Aluminum Fluoride

200

150

NR

160

200

Boric Acid

140

100

100

140

185

Copper Nitrate

200

150

100

160

200

Aluminum Hydroxide

200

NR

100

100

200

Brine, Acid

200

---

---

160

200

Copper Sulfate

200

150

NR

160

200

Aluminum Nitrate

200

150

73

100

100

Bromobenzene

NR

NR

NR

NR

150

Corn Oil

NR

Gr. A

73

NR

200

Aluminum Phosphate

200

---

100

---

---

Bromotoluene

NR

NR

NR

NR

NR

Corn Syrup

---

Gr. A

100

100

185

Butadiene

NR

NR

NR

140

185

Corrosion Inhibitors (for heating systems)

NR

---

---

---

---

Butane

NR

100

NR

70

185

Cotton Seed Oil

NR

Gr. A

NR

---

185

Aluminum Potassium Sulfate

200

100

100

160

200

Aluminum Salts

200

---

100

---

---

Aluminum Sulfate

200

150

100

140

185

Butanol (see Butyl Alcohol)

200

150

---

140

75

Creosote

NR

100

---

NR

73

Alums

200

150

---

160

NR

Butter

NR

Gr.A

NR

NR

NR

Creosote, Coal Tar

NR

---

---

---

140

Ammmonia

175

---

NR

150

NR

"Butyl "Cellosolve Adipate"

100

100

100

---

NR

Creosote, Wood

NR

---

---

---

140

Ammonia Anhydrous (Pure Ammonia)

NR

NR

NR

NR

NR

Butyl Acetate

140

NR

NR

NR

NR

Cresol

NR

NR

NR

NR

100

Ammonia, Gas

140

100

---

140

NR

Butyl Acetyl Ricinoleate

200

100

---

---

---

Cresylic Acid, to 50%

NR

---

---

---

185

Ammonia, Aqua, 10 - 25%

140

---

---

---

NR

Butyl Alcohol

200

150

73

140

75

Crude Oil

NR

---

NR

---

200

Ammonia Hydroxide

175

---

---

150

NR

Butyl Cellosolve

140

NR

---

---

NR

Crude Oil, Sour

NR

150

---

---

200

Ammonium Acetate

140

---

100

140

73

Butyl Stearate

NR

150

---

NR

200

Cumene

NR

---

---

NR

200

Ammonium Bifluoride

200

150

---

---

200

Butylene

NR

150

---

NR

100

Cupric Fluoride

200

150

---

---

---

Ammonium Carbonate

200

---

NR

140

200

Butylene Glycol

150

150

---

---

---

Cupric Sulfate

200

150

---

160

200

Ammonium Chloride

200

150

NR

160

200

Butyne Diol

NR

NR

NR

NR

NR

Cuprous Chloride

200

---

---

70

200

Ammonium Fluoride, to 10%

200

100

---

100

---

Butyric Acid

140

NR

NR

NR

70

Cyclohexane Alycyclic (Hydrocarbon)

NR

100

NR

NR

185

Ammonium Hydroxide

200

---

NR

150

70

Cadmium Cyanide

---

---

---

70

---

Cyclohexanol

NR

100

NR

NR

185

Ammonium Metaphosphate 200

---

---

---

200

Calcium Acetate

NR

100

NR

---

---

Cyclohexanone

70

NR

NR

NR

NR

NR

160

100

Calcium Bisulfate

NR

100

NR

---

---

Detergents

200

100

73

160

200

Ammonium Nitrate

200

150

Ammonium Nitrite

200

100

73

---

---

Calcium Bisulfide

NR

100

NR

---

185

Dextrin

NR

150

---

---

200

Ammonium Persulfate

200

NR

100

70

---

Calcium Bisulfite

100

100

73

70

185

Dextrose

140

---

---

160

200

Ammonium Phosphate

200

150

100

140

185

Calcium Carbonate

200

100

100

70

200

Diacetone Alcohol

70

73

NR

NR

NR

Ammonium Sulfamate

---

150

---

---

---

Calcium Chlorate

140

---

100

70

185

Dibutoxy Ethyl Phthalate

70

---

---

NR

200
NR

Ammonium Sulfate

200

150 NR

160

200

Calcium Chloride

200

150

100

160

200

Ammonium Sulfide

200

100

---

---

200

Calcium Hydrochloride

200

---

---

---

---

---

---

---

70

185

Calcium Hydroxide

200

100

NR

70

200

Ammonium Thiocyanate

Dibutyl Phthalate

70

73

NR

NR

Dichloro Difloro Methane

---

150

---

---

---

Dichloroethylene

NR

---

---

NR

185

Amyl Acetate

70

---

NR

NR

NR

Calcium Hypochlorite

70

100

NR

---

185

Dicyclohexylamine

---

73

---

---

---

Amyl Alcohol

200

---

NR

140

185

Calcium Nitrate

200

150

100

100

200

Diesel Oil

NR

150

NR

NR

185

Amyl Borate

NR

100

---

---

---

Calcium Oxide

200

100

NR

160

---

Diethyl Cellosolve

NR

---

---

100

200

Amyl Chloride

NR

NR

NR

NR

200

Calcium Sulfate

200

150

100

160

200

Diethyl Ether

NR

73

NR

---

NR

Amyl Chloronaphthalene

NR

70

NR

---

---

Calcium Sulfide

200

100

100

---

---

Diethyl Sebacate

100

100

100

---

---

Aniline

140

---

NR

NR

140

Caliche Liquors

200

100

100

---

---

Diethylamine

70

100

NR

---

NR

Aniline Hydrochloride

NR

NR

NR

NR

185

Camphor Crystals

200

---

---

NR

200

Diethylene Glycol

200

150

NR

---

---

Aniline Oil

100

---

---

---

---

Cane Sugar Liquors

200

Gr. A

100

160

200

Digester Gas

NR

150

---

---

---

Animal Fats

NR

Gr. A

100

---

---

CarbitolTM

140

100

73

70

70

Dimethylamine

140

150

---

NR

NR

Anthraquinone

NR

NR

NR

NR

200

Carbon Dioxide, Dry

140

150

---

160

200

Dioctyl Phthalate

70

NR

NR

NR

70

Anthraquinone Sulfonic Acid

NR

NR

NR

NR

200

Carbon Dioxide, Wet

140

150

---

160

200

Dioxane

70

NR

---

NR

NR

Antimony Chloride

100

---

---

---

---

Carbon Disulfide

NR

---

---

NR

200

Dipentene (Terpene-Hydrocarbon) NR

73

73

---

---

Antimony Tricholoride

140

---

100

140

185

Carbon Monoxide

200

100

100

70

200

Diproplylene Glycol

---

100

---

---

---

Anyiline Hydrochloride

---

NR

---

---

185

Carbon Tetrachloride

NR

NR

NR

NR

185

Disodium Phosphate

200

---

---

---

---

Argon Gas

200

NR

100

100

200

Carbonic Acid, Fenol

200

100

100

70

200

Divinylbenzene

NR

---

---

---

200

Aroclors

NR

NR

---

---

100

Caster Oil

140

Gr. A

NR

100

---

Dowtherm A

NR

NR

NR

---

140

Arsenic Acid, to 75%

185

150

100

NR

200

Caustic Potash

140

---

---

160

NR

Dowtherm E

NR

NR

NR

---

140

Arylsulfonic Acid

140

NR

NR

NR

185

Cellosolve

140

NR

NR

---

NR

Dowtherm SR-1

100

100

---

---

---

ASTM #1, 2 & 3 Oil

NR

150

NR

NR

100

Cellulose Acetate

140

NR

NR

NR

NR

Epsom Salt

200

100

---

---

---

148
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011
Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Ethanolamine

140

NR

---

---

---

Hydraulic Oil

NR

---

NR

70

200

Methylene Iodine

200

---

---

---

---

Ethers

NR

NR

NR

NR

NR

Hydrobromic Acid, to 50%

140

100

---

70

185

MIL-05606

NR

NR

---

---

100
100

"Ethyl "Cellusolve"

100

NR

NR

---

---

Hydrochloric Acid, to 37%

75

NR

NR

---

158

MIL-08515

NR

NR

---

---

Ethyl Acetoacetate

100

NR

73

---

NR

Hydrocyanic Acid, to 10%

200

NR

---

---

185

MIL-L7808

NR

NR

NR

---

100

Ethyl Acrylate

70

NR

100

NR

NR

Hydrofluoric Acid, to 30%

NR

NR

NR

70

150

Milk

200

Gr. A

100

160

200

Ethyl Alcohol (Ethanol)

200

150

NR

---

---

Hydrofluosilicic Acid, to 50%

140

150

---

---

200

Mineral Oils

NR

150

NR

70

200

Ethyl Cellulose

NR

73

NR

---

---

Hydrogen Gas

200

73

NR

160

100

Molasses

100

100

100

150

185

Ethyl Chloride

70

100

NR

70

140

Hydrogen Peroxide, to 30%

140

NR

100

NR

200

Monochloroacetic Acid, to 50%

NR

---

---

NR

70

Ethyl Ether

NR

70

---

NR

NR

Hydrogen Phosphide

NR

NR

NR

NR

NR

Monoethanolamine

70

NR

NR

NR

185

Ethyl Oxalate

100

NR

NR

---

---

Hydrogen Sulfide.

100

NR

NR

NR

140

Motor Oil

NR

150

NR

---

200

Ethyl Silicate

100

100

---

---

---

Hydroquinone

NR

150

100

NR

185

Naphta

NR

160

NR

NR

160

Ethylene

NR

100

NR

NR

140

Hydroxylamine Sulfate

70

---

---

70

---

Naphtalene

NR

NR

NR

NR

170

Ethylene Chlorohydrin

70

NR

NR

70

NR

Hypochlorous Acid

70

---

---

---

70

Naphtenic Acid

NR

100

NR

---

---

Ethylene Diamine

70

100

---

100

---

Iodine Solution, to 10%

150

---

---

---

200

Natural Gas

NR

150

100

140

185
NR

Ethylene Dichloride (Dichloroethane)

NR

---

---

NR

120

Isobutyl Alcohol

180

100

NR

---

---

Nickel Acetate

70

NR

NR

100

Ethylene Glycol

200

150

73

160

200

Isododecane

NR

100

NR

100

---

Nickel Ammonium Sulfate

70

---

---

100

---

Ethylene Oxide

NR

NR

NR

NR

NR

Isooctane

NR

100

NR

70

185

Nickel Chloride

200

150

100

160

200

Fatty Acid

NR

Gr. A

NR

140

185

Isooctyle Alcohol

140

---

---

---

---

Nickel Nitrate

180

100

100

160

200

Ferric Chloride, to 35%

200

150

NR

160

200

Isopropyl Acetate

140

NR

NR

---

---

Nickel Sulfate

200

150

---

160

200

Ferric Hydroxide

180

---

---

100

180

Isopropyl Alcohol

140

100

NR

70

160

Nicotine

NR

---

---

70

---

Ferric Nitrate

200

100

100

160

200

Isopropyl Ether

NR

100

NR

NR

NR

Nicotine Acid

70

---

---

70

---

Ferric Sulfate

200

100

NR

140

185

Jet Fuel, JP-4

NR

150

NR

NR

200

Nitric Acid, to 10%

75

---

100

NR

185

Ferrous Chloride

200

100

NR

---

200

Jet Fuel, JP-5

NR

150

NR

NR

200

Nitric Acid, 10 - 50%

NR

---

100

NR

160

Ferrous Hydroxide

180

---

---

---

180

Kerosene

NR

150

NR

70

200

Nitric Acid, Red Fuming

NR

---

---

NR

100
70

Ferrous Nitrate

180

---

---

160

200

Ketones

NR

NR

NR

NR

NR

Nitrobenzene

70

NR

NR

---

Ferrous Sulfate

200

150

100

160

200

Lactic Acid

70

Gr. A

---

140

70

Nitrocellulose

---

100

100

100

---

Fire Fighting Form (AFFF)

180

---

---

---

---

Lard Oil

NR

Gr. A

---

70

185

Nitroethane

100

NR

NR

---

-----

Fish Oils (Solubles)

NR

Gr. A

73

---

70

Latex (1% Styrene & Butadiene)

NR

NR

NR

NR

140

Nitrogen

180

150

---

---

Fluboric Acid

140

---

NR

160

140

Lauric Acid

NR

100

NR

NR

100

Nitromethane

70

NR

NR

---

---

Fluorine Gas, Wet

NR

NR

NR

NR

NR

Lauryl Chloride

140

NR

NR

NR

200

Nitrous Acid, to 10%

NR

---

100

---

100

Fluorosilicic Acid, to 30%

140

100

---

100

200

Lavender Oil

NR

100

NR

---

---

Nitrous Oxide

NR

100

100

NR

70

Fly Ash

180

---

---

---

---

Lead Acetate

200

150

NR

160

NR

Octyl Alcohol

NR

100

100

100

---

FM200

200

---

200

200

---

Lead Chloride

NR

---

---

70

140

Ogisogiric Acid, to 75%

NR

NR

NR

NR

150

Oleic Acid

70

100

NR

70

185

Oleum

NR

NR

100

NR

NR

Olive Oil

---

Gr. A

NR

140

150

Foam

180

---

---

---

---

Lead Nitrate

175

100

100

140

200

Fog Oil

NR

100

---

---

---

Lead Sulfamate

140

73

100

---

---

Formaldehyde

140

100

NR

140

NR

Lead Sulfate

200

150

---

140

200

Formanide

NR

100

---

---

---

Lemon Oil

---

Gr. A

NR

100

200

Oronite 8200 Silicate Ester Fluid

NR

NR

---

---

150

Formic Acid, to 25%

200

100

---

140

NR

Ligroine

---

100

NR

70

100

Orthodichlorobenzene

NR

NR

NR

---

150

Freon F-11

NR

130

NR

NR

70

Lime and H_O

180

150

---

---

---

OS-45 Silicate Ester Fluid

NR

NR

---

---

150

Freon F-113

NR

130

NR

130

130

Lime Sulfur

200

NR

100

100

185

OS-45-1

NR

NR

NR

---

150

Freon F-114

NR

130

NR

70

NR

Linoleic Acid

70

73

NR

---

140

Oxalic Acid

150

---

---

100

100

Freon F-12

NR

130

NR

130

NR

Linseed Oil

70

Gr. A

NR

70

200

Oxygen

200

NR

NR

140

185

Freon 123

NR

NR

NR

NR

NR

Lithium Bromide (Brine)

---

100

---

---

200

Ozone (100 ppm)

200

100

100

NR

185

Freon 134a

NR

NR

NR

NR

NR

Lithium Chloride

100

100

---

---

140

Palm Oil

NR

Gr. A

---

---

70

Freon F-21

NR

NR

NR

NR

NR

Lubricating Oil, ASTM#1,#2,#3

NR

150

---

180

150

Palmitic Acid

70

150

---

NR

185

Freon F-22

NR

NR

---

130

NR

Magnesium Ammonium Sulfate

NR

NR

NR

70

NR

Paraffin

NR

100

NR

140

200

Fructose

175

150

---

160

200

Magnesium Carbonate

170

100

100

140

200

Peanut Oil

NR

Gr. A

100

---

150
200

Fruit Juice, Pulp

---

Gr. A

---

---

200

Magnesium Chloride

170

150

100

160

170

Pentachlorophenol

NR

---

---

NR

Fuel Oil

NR

150

NR

---

100

Magnesium Citrate

175

---

---

---

200

Pentane

---

100

---

---

---

Fumaric Acid

100

100

---

---

100

Magnesium Fluoride

140

---

---

---

200

Perchloric Acid, to 10%

70

NR

NR

70

70

Furan

NR

NR

NR

NR

NR

Magnesium Hydroxide

200

150

100

---

200

Perchloric Acid, to 70%

70

NR

NR

NR

185

Furfural

140

---

---

70

NR

Magnesium Nitrate

200

100

100

160

---

Perchloroethylene

---

---

---

---

150

Furfuryl Alcohol

140

NR

---

---

---

Magnesium Oxide

140

73

---

160

---

Petroleum Ether (see Benzene)

NR

NR

NR

NR

150

Gallic Acid

70

100

NR

70

185

Magnesium Sulfate

175

150

100

160

200

Petroleum Oils

NR

150

NR

---

200

Gasoline, Leaded

NR

---

---

70

100

Maleic Acid, Saturated

70

100

---

NR

200

Phenol (Carbolic Acid)

70

NR

NR

NR

200

Gasoline, Refined

NR

100

---

---

---

Malic Acid

---

100

100

---

---

Phenylhydrazine

NR

---

---

---

NR

Gasoline, Sour

NR

---

---

---

100

Manganese Sulfate

175

---

---

160

200

Phenylhydrazine Hydrochloride

70

---

---

---

---

Gasoline, Unleaded

NR

100

---

---

100

Mercuric Chloride

200

150

100

140

185

Phosohoric Acid, to 10%

140

100

NR

140

200

Gelatin

200

Gr. A

73

160

200

Mercuric Cyanide

70

100

100

70

70

Phosohoric Acid, 10 - 50%

70

100

NR

70

200

Glucose

200

Gr. A

100

160

200

Mercurous Nitrate

70

100

---

NR

70

Phosphorous Pentoxide

200

---

---

---

200
185

Glue

150

150

73

---

---

Mercury

200

150

100

140

185

Photographic Solutions

100

150

100

---

Glycerine

200

150

100

160

200

Methane

NR

70

NR

70

185

Phthalic Anhydride

100

NR

NR

---

---

Glycerol

150

100

---

---

---

Methyl Acetate

140

NR

NR

140

---

Picric Acid

140

100

NR

70

140

Glycol

180

100

73

---

---

Methyl Alcohol, Methanol

140

140

NR

140

NR

Pine Oil

---

NR

NR

NR

70

Glycolic Acid

NR

73

73

70

NR

Methyl Amine

70

---

---

70

100

Plating Solutions, Brass

70

---

---

100

70

Grape Sugar, Juice

200

Gr. A

---

160

185

Methyl Butyle Ketone

140

---

---

---

---

Plating Solutions, Cadmium

70

---

---

100

70

Grease

NR

150

NR

---

185

Methyl Bromide

NR

100

NR

NR

185

Plating Solutions, Chrome

---

---

---

NR

140

Green Sulfate Liquor

180

150

100

70

---

Methyl Cellosolve

70

NR

NR

70

NR

Plating Solutions, Copper

70

---

---

100

70

Halon 1301

180

NR

---

---

140

Methyl Chloride

NR

NR

NR

NR

70

Plating Solutions, Gold

70

---

---

125

70

Heptane

NR

100

---

70

185

Methyl Cyclopentane

NR

NR

NR

70

70

Plating Solutions, Lead

70

---

---

70

70

Hexaldehyde

180

NR

100

---

---

Methyl Ethyl Ketone

70

NR

NR

NR

NR

Plating Solutions, Nickel

125

---

---

70

70

Hexane

NR

70

NR

70

70

Methyl Formate

100

NR

100

70

NR

Plating Solutions, Silver

70

---

---

100

70

Hexanol

NR

---

---

70

160

Methyl Isobutyl Ketone

NR

NR

NR

NR

NR

Plating Solutions, Tin

100

---

---

100

140

Plating Solutions, Zinc

70

---

---

100

70

Hexanol Tertiary

NR

100

---

---

---

Hexyl Alcohol

NR

100

NR

100

185

Hexylene Glycol

NR

100

---

---

---

Methylene Chloride

NR

NR

---

NR

73

Methylene Chlorobromide

NR

NR

NR

NR

NR

Methylene Dichloride

NR

---

---

---

100

Connect with the Best!

www.shurjoint.com

149
Copyright 2011 Shurjoint

Catalog 2011
Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Polyvinyl Acetate, Solid in


Liquid State is 50% solution of

Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Sodium Ferricyanide

140

100

---

---

140

Turbo Oil #15 Diester Lubricant

NR

NR

---

---

150

Sodium Ferrocyanide

140

100

---

---

140

Turpentine

NR

100

---

NR

150

Sodium Fluoride

140

100

NR

70

140

Urea

200

150

100

140

185
70

180

---

---

---

---

---

160

200

Sodium Hydroxide, to 15%

180

NR

NR

160

NR

Urine

200

100

---

140

Potassium Acetate

170

150

NR

---

---

Sodium Hypochlorite, to 20%

70

100

---

NR

185

Vaseline

NR

---

---

140

70

Potassium Alum

200

100

---

160

200

Sodium Metaphosphate

70

100

---

---

70

Vegetable Oils

NR

Gr. A

100

70

200

Methanol or 60% solution of (H2O)


Potash

Potassium Aluminum Sulfate

200

---

---

160

200

Sodium Nitrate

200

NR

NR

140

200

Vinegar

180

Gr. A

100

70

NR

Potassium Bicarbonate

170

150

---

160

200

Sodium Nitrile

170

150

---

140

200

Vinyl Acetate

70

NR

NR

NR

NR

Potassium Bisulfate

170

---

---

140

200

Sodium Perborate

70

70

NR

70

70

Vinyl Chloride

NR

NR

NR

NR

70

Potassium Borate

200

---

---

---

200

Sodium Peroxide

140

NR

NR

70

185

Vi-Pex

---

100

---

---

---

Potassium Bromate

---

---

---

140

200

Sodium Phosphate, Acid

170

---

---

140

200

Water

230

150

100

160

200

Potassium Bromide

170

150

---

160

200

Sodium Phosphate, Alkaline

170

---

---

140

200

Water, Acid Mine

200

150

---

160

---

Potassium Carbonate

170

150

100

160

200

Sodium Phosphate, Neutral

170

---

---

140

200

Water, Bromine

NR

NR

NR

NR

185

Potassium Chlorate

140

100

100

100

140

Sodium Silicate

200

150

---

140

200

Water, Chlorinated, to 3500ppm

100

---

---

NR

185

Potassium Chloride

200

150

100

160

200

Sodium Sulfate

140

100

100

140

200

Water, Chlorinated, above 3500ppm

NR

---

---

NR

185

Potassium Chromate

170

150

---

70

200

Sodium Sulfide

140

100

100

140

200

Water, Deionized

200

150

100

160

---

Potassium Cyanide

140

100

100

160

185

Sodium Sulfite

140

100

100

140

200

Water, Demineralized

200

150

---

160

200

200

150

100

160

---

---

160

---

Potassium Dichromate

170

100

100

---

200

"Sodium Thiosulfate "hypo"

200

150

100

160

200

Water, Distilled

Potassium Ferrocyanide

140

NR

---

150

140

Sohovis 47

---

100

---

---

---

Water, Potable

Potassium Fluoride

140

---

---

---

---

Sohovis 78

---

100

---

---

---

Water, Salt

200

150

---

160

---

Potassium Hydroxide

140

150

NR

160

NR

Solvasol #1,2 & 3

---

100

---

---

---

Water, Sewage

200

150

---

---

---

Gr. E-pw Gr. A

Potassium Iodide

140

---

100

160

180

Solvasol #73

---

70

---

---

---

Water, Seawater

200

150

---

160

---

Potassium Nitrate

200

150

100

140

200

Solvasol #74

NR

NR

NR

NR

NR

Water, Swimming Pool

200

150

---

---

---

---

---

---

70

---

Soybean Oil

NR

Gr. A

73

---

200

Water, waste

200

150

---

---

---

140

150

---

---

150

Spindle Oil

NR

100

---

Whiskey

200

Gr. A

100

140

140

Potassium Perborate
Potassium Perchlorate

Potassium Permanganate, to 10% 200

150

---

100

140

Stannic Chloride

100

100

100

NR

200

White Liquor

170

Gr. A

---

140

---

Potassium Permanganate, to 25% 140

100

---

100

140

Stannous Chloride

70

NR

NR

160

200

Wines

170

Gr. A

100

140

140

Potassium Persulfate

200

150

---

140

200

Starch

170

100

---

160

200

Wood Oil

NR

100

NR

---

---

Potassium Silicate

200

150

---

140

---

Steam

NR

NR

NR

NR

NR

Xylene

NR

NR

NR

NR

150

Potassium Sulfate

200

150

NR

140

200

Stearic Acid

NR

100

NR

70

100

Zinc Acetate

180

100

NR

160

70

Prestone

---

100

---

---

---

Stoddard Solvent

NR

100

NR

NR

185

Zinc Chloride

180

100

100

160

200

Propane Gas

NR

100

NR

70

70

Styrene

NR

NR

NR

NR

100

Zinc Nitrate

180

---

---

---

200

Propanol

---

---

---

---

---

Sucrose Solutions

---

Gr. A

---

---

---

Zinc Sulfate

180

100

100

140

200

140

---

---

NR

140

Sulfamic Acid

NR

---

---

70

NR

Propargyl Alcohol
Propyl Acetate

NR

NR

NR

140

---

Sulfite Liquor

140

---

---

70

140

Propyl Alcohol

140

150

100

140

---

Sulfer Dioxide, Dry

140

100

---

---

---

Propylene Dichloride

NR

---

70

NR

70

Sulfonic Acid

150

---

---

---

---

Propylene Glycol

200

100

100

100

140

Sulfur

140

NR

NR

70

200

Propylene Oxide

70

NR

NR

NR

NR

Sulfur Chloride

NR

NR

NR

NR

70

Pydraul F-9 and 150

NR

NR

NR

NR

NR

Sulfur Dioxide, Dry

70

NR

---

NR

100

Pyranol 1467

NR

100

100

---

---

Sulfur Dioxide, Wet

140

NR

---

---

140

Pyranol 1476

NR

100

100

---

---

Sulfur Trioxide

70

NR

NR

NR

140

"Pyroguard "C"

---

100

100

---

---

Sulfuric Acid, 10 - 30%

150

NR

73

100

200

"Pyroguard "D"

---

100

100

---

---

Sulfuric Acid, Fuming

NR

NR

NR

NR

100

Pyroguard 55

180

---

NR

---

---

Sulfuric Acid, Oleum

NR

NR

NR

NR

100

Pyrrole

100

NR

73

---

---

Sulfurous Acid

75

NR

NR

NR

100

Rapeseed Oil

NR

Gr. A

NR

---

---

Tall Oil

NR

70

---

70

70

Ref. Fuel (ISO Octane, 30 Toluene)

---

150

---

---

---

Tannic Acid, all conc.

70

100

73

100

100

Rosin Oil

NR

100

---

100

---

Tannic Acid, Liquors

100

---

---

70

200

Salicylic Acid

200

100

100

NR

185

Secondary Butyl Alcohol

Tanning Liquors( 50g. alum.

---

100

---

---

---

Solution, 50g. dichromate solution)

NR

150

---

70

200

Sewage

200

150

100

---

---

Tar

NR

100

100

70

185

Silicic Acid

140

---

---

140

200

Terpienol

NR

NR

---

70

185

Silicone Oil

140

100

NR

70

185

Tertiary Butyl Alcohol

140

100

---

70

150

Silver Cyanide

140

---

---

70

140

Tetrabutyl Tinanate

140

100

---

---

185

Silver Nitrate

200

NR

100

160

200

Tetrachloroethylene

NR

---

---

---

150

Silver Sulfate

170

---

---

---

200

Tetrahydrofuran

NR

NR

NR

NR

NR

Skydrol 200

200

---

200

---

---

Tetralin

NR

NR

NR

NR

NR

Skydrol 500 Phosphate Ester 170

---

---

---

---

Tetraric Acid

140

---

---

---

---

200

150

100

140

200

Thionyl Chloride

NR

NR

100

NR

100

Soda Ash, Sodium Carbonate 180

100

---

---

---

Thiopene

NR

NR

NR

NR

NR

Sodium Acetate

170

NR

NR

---

NR

Thread Cutting Oil

NR

NR

NR

NR

70

Sodium Alum

170

150

---

140

200

Titanium Tetracholoride

NR

NR

NR

---

185

Sodium Aluminate

200

100

---

140

200

Toluene, to 30%

NR

100

---

---

70

Sodium Benzoate

200

150

100

---

200

Tomato Juice

200

Gr. A

---

70

200

Sodium Bicarbonate

200

150

NR

160

200

Transformer Oil

140

150

---

NR

140

Sodium Bichromate

140

---

---

70

200

Transmission Fluid, Type A

NR

150

---

---

140

Sodium Bisulfate

200

150

NR

140

200

Triacetin

NR

100

---

---

---

Sodium Bisulfite (Black Liquor)

200

150

NR

140

200

Trichloroethane

NR

NR

NR

---

200

Sodium Borate

140

100

NR

100

140

Trichloroethylene

NR

---

---

NR

200

Sodium Bromide

200

150

---

70

200

Tricresyl Phosphate

NR

NR

NR

---

---

Sodium Carbonate

140

150

100

140

200

Triethanolamine

70

70

NR

70

NR

Sodium Chlorate

140

NR

100

140

100

Triethylamine

---

100

NR

70

200

Sodium Chloride

140

100

NR

160

200

Trimethylpropane

180

---

---

160

---

Sodium Cyanide

140

100

NR

140

140

Trisodium Phosphate

70

---

100

70

185

Sodium Dichromate

140

100

---

NR

200

Tung Oil

NR

100

---

---

---

Soap Solutions

150
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

Fire Protection Services


The Shurjoint fire protection series
numbers over 600 individual
components, including grooved
couplings, fittings, flanges,
mechanical tees, valves, welding
outlets, threaded fittings and more.
Applicable products are listed and
or approved by various domestic
and international approval bodies
including UL, FM, VdS, LPCB and
others.
HYDROSTATIC TESTS A p p r o v e d

products are rated in cold water pressure

(CWP) tested with a 3 to 5 times test


pressure depending on the approval body
and pipe size. The minimum working

See the table below for the bending

and larger, the angular movement shall be

moments per UL and FM on Sch. 40 pipe.

permitted to be less than 1 degree but not

This bending moment is twice that required

less than 0.5 degrees. (NFPA 13 - 2007

by ASTM F1476 (refer to page 13).

3.5.4)

Required Bending Moment by UL & FM

the use of flexible couplings to protect the

For sprinkler systems, NFPA 13 specifies

Nom.

Size
(inches)

1

2

2

3

4

5

6

8

10

12

14

16

UL
FM
Moment Moment Moment Moment
N-m
Lb-Ft
N-m
Lb-Ft
1098
810
1100
810
1559
1150
1560
1150
2400
1770
2400
1770
3289
2426
3290
2425
4942
3645
4975
3670
7102
5238
7105
5240
9606
7085
9615
7090
15326
11304
15335
11310
22757
16785
22790
16805
31116
22950
31145
22970
37217
27450
48597
35843

system against damage from earthquakes


and lists some specific examples of how
and where they should be used. Designers
and installers should design their fire
protection systems in compliance with this
standard. See Typical Applications Flexible

Couplings on Page 154.

pressure (CWP) shall be 175 psi (12.3


Bar) in accordance with NFPA 13. Approval
testing of a coupling is conducted on all

Pipe

Force, F40
Test Joint

Capped
End

different pipe schedules as enrolled and


approved working pressures (CWP) are
assigned to each individual combination

Capped
End

of the coupling and test pipe. Refer to the

Approved Pressure Ratings by UL and FM.


Up to 6 / 150
8 12 / 200 -300
14 and above

requirements including gasket performance

UL

FM

VdS

LPCB

X5
X4
X3

X4
X4
X4

X4
X4
NA

X4
X4
NA

Contact Shurjoint for other approvals.

Pipe

In addition to the hydrostatic and bending


moment tests, couplings must meet other

Hydrostatic Test Pressures


(= multiple of CWP)
Nom. Size

Support Spacing, LS

tests.

FLEXIBLE COUPLING NFPA 13 defines

a flexible coupling as a listed coupling


or fitting that allows axial displacement,

Test Joint

Capped
End

rotation, and at least 1 degree of angular


movement of the pipe without inducing harm
on the pipe. For pipe diameters of 8 in.

Minimum Overall
Length 2 ft (610 mm)

Capped
End

Force, F40

Capped

Test Joint
BENDING
TESTS End
The
PipeMOMENT

required bending moment per UL and FM

is calculated based on twice the weight of


water
Cappedfilled pipe over twice the maximum
Support Spacing, LS

End

distance between pipe supports as specified


in NFPA 13.
Lhs = 15 ft

Lhs = 15 ft

Water Filled
Schedule 40 Steel
Sprinkler Pipe

Connect with the Best!

www.shurjoint.com

151
Copyright 2011 Shurjoint

Catalog 2011

Approved Pressure Ratings by UL & FM


6. Approved grooved couplings may be used in underground service

1. Approved grooved couplings and fittings are good for use in both

subject to the installation restrictions placed upon the pipe and to

wet and dry sprinkler systems.

the coupling manufacturers recommendations and requirements.

2. Typical applications of flexible couplings (models 7705, 7706

7. Approved grooved couplings have been evaluated for a maximum

& 7707) are in sprinkler risers, in feed mains passing through

ambient temperature of 225F (107C), suitable for normal

walls from one building area to another, in locations subject to

warehouse protection.

earthquakes, in the discharge line from aboveground pump suction

8. Threaded size of sprinkler piping is limited to 1 inch (25mm)

tanks, in new connections to existing feed mains and in air or

nominal.

water fire service lines subject to excessive vibration or difficult

9. Threaded connections can be made to approved threadable

alignment.

thinwall pipe or to Schedule 40 pipe.

3. Approved grooved couplings are limited to use with rolled or cutgroove ended pipe, valves and fittings at a minimum rated working

Source: FM Approval Guide

pressure of 175 psi (1205 kPa) and are suitable for aboveground

For pressure ratings for special pipes, DIN and JIS pipe sizes, and large diameter
sizes 14 24, contact Shurjoint for details.
Models K-9 and 7771 rigid couplings are also available. For pressure ratings,
contact Shurjoint for details.

service.
4. Grooves should be processed according to ANSI/AWWA C606
(latest edition) Grooved and Shouldered Joints.
5. Installation must be made according to the manufacturers
instructions and requirements.

Couplings and Flange Adapters


Sch. 40 & STD Wall Pipe














Size
in

1
1
1
2
2
3
4
5
6
8
10
12

Wall
in
0.113
0.133
0.140
0.145
0.154
0.203
0.216
0.237
0.258
0.280
0.322
0.375
0.375

UL
-
300
300
300
300
300
300
300
300
300
300
175^
175*

Unit: psi

7705
FM
-
300
300
300
300
300
300
300
300
300
300
250
250

UL
500
500
500
500
500
500
500
500
500
500
500
300
300

7707
FM
500
500
500
500
500
500
500
500
500
500
500
500
300

UL
-
-
350
350
350
350
350
350
350
350
350
-
-

Z05
FM
-
-
350
350
350
350
350
350
350
350
350
-
-

UL
-
-
350
350
350
350
300
350
350
350
-
350
-
350
NA
NA

Z05
FM
-
-
350
350
350
350
-
350
350
350
-
350
-
350
NA
NA

UL
-
500
500
500
500
500
500
500
400
400
400
350
350

Z07
FM
-
500
500
500
500
500
500
500
400
400
400
350
350

UL
-
500
500
500
500
500
-
500
500
400
-
400
-
400
350
350

Z07
FM
-
500
500
500
500
500
-
500
500
400
-
400
-
400
350
350

UL
-
-
-
-
175
175
175
175
175
175
175
175
175*

7041
FM
-
-
-
-
175
175
175
175
175
175
175
175
175

UL
-
-
-
-
300
300
300
300
300
300
300
300
300

7043
7706
FM
Size (in)
UL
FM
-
2 x 1
300
300
-
2 x 2
300
300
-
3 x 2
300
300
-
3 x 2
300
300
300
4 x 2
300
300
300
4 x 2
300
300
300
4 x 3
300
300
300
6 x 3
300
300
300
6 x 4
300
300
300
8 x 6
300
300
300
300
300

UL
-
-
-
-
175
175
175
175
175
175
175
175
175
175
175
175*

7041
FM
-
-
-
-
175
175
-
175
175
175
-
175
-
175
175
175

7043
UL
FM
Size (in)
-
-
2 x 1
-
-
2 x 2
-
-
76.1 x 2
-
-
3 x 2
300
300
3 x 2
300
300
3 x 76.1
-
-
4 x 2
300
300
4 x 2
300
300
4 x 76.1
300
300
4 x 3
-
-
6 x 3
300
300
165.1 x 3
-
-
6 x 4
300
300
165.1 x 4
300
300
8 x 6
300
300
8 x 165.1

^ 0.188" wall, * 0.330 wall


Unit: psi

Size
in
8

Wall
in
0.322

7705H

UL
450

FM
450

Sch. 10 & BS1387 Medium Pipe


Size


in



1
1
1

2
2
76.1

3

4

5
139.7

6
165.1

8
10
12

Wall
in
0.083
0.109
0.109
1.109
0.110
0.120
0.142
0.120
0.120
0.134
0.197
0.134
0.197
0.188
0.188
0.250

7705
UL
FM
-
-
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
175
175
175*
175

Wall
in
0.188

7705H

Unit: psi

7707
UL
FM
500
500
500
500
500
500
500
500
450
450
450
450
500
500
450
450
450
450
450
450
500
500
450
450
500
500
450
450
300
450
300
300

* 0.330 wall
Unit: psi

Size
in
8

152
Copyright 2011 Shurjoint

UL
450

FM
450

Connect with the Best!

www.shurjoint.com

7706
UL
FM
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300

Catalog 2011

Approved Pressure Ratings by UL and FM


Outlet Coupling and Mechanical Tees


Model


C-7 Outlet

Coupling,

Threaded



C-7 Outlet

Coupling,

Grooved







M21

Mechanical

Tee, Threaded

(NPT or BSPT)










M22

Mechanical

Tee, Grooved







7721 Threade

(NPT or BSPT)


7722 Grooved



723 Threaded

(NPT or BSPT)

Sizes (in)
(run x branch)
1 x , & 1
2 x , & 1
2 x , & 1
3 x & 1
4 x & 1
6 x 1 & 1
2 x 1
2 x 1 & 1
3 x 1 & 1
4 x 1 & 2
6 x 1 & 2
2 x , , 1, 1 & 1
2 x , , 1, 1 & 1
76.1 x 15, 20, 32 & 40
3 x , , 1, 1, 1 & 2
4 x , , 1, 1, 1, 2 & 2
100 x 65 (76.1)
4 x 3
5 x 2 & 2
125 (139.7) x 50, 65 (76.1) & 80
6 x 1, 1, 2 & 2
6 x 3 & 4
150 (165.1) x 32, 40, 50 & 65 (76.1)
150 (165.1) x 80 & 100
2 x 1, 1 & 1
2 x 1, 1 & 1
76.1 x 25, 32 & 40
3 x 1, 1, 1 & 2
4 x 1, 1, 1, 2 & 2
100 x 65 (76.1)
5 x 2 & 2
4 x 3
125 (139.7) x 65 (76.1)
6 x 1, 1, 2 & 2
6 x 3 & 4
150 (165.1) x 32, 40, 50 & 65 (76.1)
150 (165.1) x 80 & 100
4 x 3
8 x 2, 2, 3 & 4
200 x 65 (76.1)
4 x 3
8 x 2, 2, 3 & 4
200 x 65 (76.1)
1 x x & 1
1 x x & 2
2 x x & 3
2 x x & 4

Grooved-end Fittings

Unit: psi

Sch. 40/STD
UL
FM
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
175
175
300
300
300
300
300
300
175
175
300
300
175
175
300
300
300
300
300
300
300
300
300
300
300
300
300
300
175
175
300
300
300
300
175
175
300
300
175
175
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300

Sch. 10
UL
FM
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
175
175
300
300
300
300
300
300
175
175
300
300
175
175
300
300
300
300
300
300
300
300
300
300
300
300
300
300
175
175
300
300
300
300
175
175
300
300
175
175
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300

Unit: psi


Model
Size Range
901 S/ R 90 Elbow
2" thru 8"

903 S/R Tee
2" thru 8"


1" thru 8"
7110 90 Elbow

10", 12"


1" thru 8"
7111 45 Elbow

10", 12"
7110DR Drain Elbow
2" thru 6"
7110LR 1.5D Elbow
2" thru 8"


1"
7112 22-1/2 Elbow

2" thru 8"
7113 11-1/4 Elbow
2" thru 8"


1" thru 8"
7120 Tee

10", 12"
7121 Reducing Tee
2"x1" thru 8"x6"
7125 Bullhead Tee
2"x2" thru 6"x8"
7127 Standpipe Tee
4"x2", 6x2"

7130 Lateral
2" thru 8"

7135 Cross
2" thru 6"
7150 Conc. Reducer
2"x1" thru 14"x12"
7150F Socket Adapter
1"x1" thru 6"x4"
7150M Red. Nipple
1"x1" thru 6"x4"
7160T Transition Fitting
2"x1" thru 6"x2"
7151 Ecc. Reducer
2"x2" thru 8"x6"

7160 End Cap
1" thru 12"

10" thru 12"

7160H End Cap
14" thru 18"

20" thru 24"
7170 Flange Adapter
2-1/2" thru 6"
7180 Flange Adapter
2" thru 8"
7181 Red. Flange
3"x2" thru 6"x4"
55 Nipple Adapter
1" thru 2"

899 End All
1"x" thru 2"x1"
850 Sprinkler Hub
2"x2"x1" thru 2"x2"x1"
851 Sprinkler Hub
2"x2"x1" thru 2"x2"x1"
853 Sprinkler Hub
1"x1" thru 2"x1"

UL
300
300
300
300
300
300
300
300
500
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
250
175
300
NA
300
300
300
300
300

Valves & Components



Model
RCV Riser Check Valve


726 Y-Strainer

SJ-300F Butterfly Valve
SJ-700W Butterfly Valve

FM
300
300
500
300
500
300
300
300
NA
300
300
500
300
300
300
300
300
300
300
300
300
300
300
300
300
175
175
175
300
300
300
300
300
300
300

Unit: psi

Size Range
2" thru 6"
2" thru 6"
8" thru 12"
2" thru 6"
2" thru 12"

UL
300
300
175
NA
175

FM
300
NA
NA
300
NA

Stainless Steel Series


Sch. 40S and 10S Pipe
Size
in

1
1
2

2
2

3

4

5

6

8

Sch. 10S
Wall (in)
0.109
0.109
0.109
0.109
0.120
0.120
0.120
0.134
0.134
0.148

Unit: psi

SS-7
SS-8
UL
FM
UL
FM
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
250
300
300
300
300

SS-41
SS-723
UL
FM
Size (in)
UL
-
-
1 x
300
350
350
1 x
300
350
350
1 x 1
300
350
350
1 x
300
350
350
1 x
300
350
350
1 x 1
300
350
350
2 x
300
350
350
2 x
300
350
350
2 x 1
300
350
350

FM
300
300
300
300
300
300
300
300
300

Unit: psi


Model

SS-10 90 Elbow

SS-11 45 Elbow

SS-20 Tee

SS-21 Tee

SS-21F Tee
SS-50 Conc. Reducer
SS-50F Conc. Reducer

SS-60 Cap
SS-80 Flange Adapter

Size Range
1" thru 8"
1" thru 8"
1" thru 8"
3"x2" thru 4"x2"
3"x2", 4"x2"
3"x2" thru 4"x2"
2"x2" thru 4" x 2"
1" thru 8"
2" thru 8"

UL
300
300
300
300
300
300
300
300
300


Model

C-10 90 Elbow

C-11 45 Elbow

C-20 Tee
C-21 Reducing Tee
C-26 Reducing Tee
C-50 Conc. Reducer
C-52 Conc. Reducer

C-60 Cap

Size Range
2" through 4"
2" through 4"
2" through 6"
2"x2" thrru 6"x5"
2"x" thru 4"x"
2"x2" thru 6"x5"
2"x1" thru 4"x2"
2" thru 4"

UL
200
200
200
200
200
200
200
200

FM
300
300
300
300
300
300
300
300
300

Copper Tubing Series

Type K & Type L Copper Tubing









Size
in
2
2
3
4
5
6

Type K
Wall (in)
0.083
0.095
0.109
0.134
0.160
0.192

Type L
Wall (in)
0.070
0.080
0.090
0.110
0.123
0.140

UL
200
200
200
200
200
200

C301
FM
200
200
200
200
-
200

FM: Type K only

Connect with the Best!

Unit: psi

UL
200
200
200
200
200
200

C341

FM
-

Unit: psi

www.shurjoint.com

FM
200
200
200
NA
NA
NA
NA
200

153
Copyright 2011 Shurjoint

Catalog 2011

Typical Applications - Flexible


Couplings Sprinkler Systems
(NFPA 13)

2. Flexible couplings on horizontal portion of Tie-In


Ceiling/floor assembly
24 in. (610mm)

The following illustrations are part of NFPA 13 2007 Annex A

Flexible coupling

Flexible Coupling
24 in. (610mm)

Explanatory Material. These are for informational purposes only and


not a mandatory requirement. For specific requirements for any other
areas of sprinkler systems, refer to the latest version of NFPA 13.

1. Flexible couplings for main risers and branch


line riser
Roof

Roof

24in.
(610 mm)
Maximum

4-way brace
(Pipe must rotate
within brace)
Flexible
coupling

Wall

aming

Roof fr

4-way
brace
Elbow with
flexible joints

12 in. (305mm)
Ceiling/floor assembly
FIGURE A.9.3.2.3(2) (a) Flexible Coupling on Horizontal
Portion of Tie-In.

3. Flexible Coupling on Main Riser and Branch Line


Riser
Ceiling/floor assembly

Siding
Column

24 in. (610mm)
Flexible
coupling

Flexible
coupling

Detail A

Flexible coupling

Flexible Coupling

Detail B
(Might be preferred for metal buildings)

Flexible coupling

Flexible coupling

Note to Detail A: The four-way brace should be attached above the upper flexible
coupling required for the riser and preferably to the roof structure if suitable. The
brace should not be attached directly to a plywood or metal deck.

12 in. (305mm)

FIGURE A.9.3.2(a) Riser Details.

Ceiling/floor assembly
FIGURE A.9.3.2.3(2) (b) Flexible Coupling on Main Riser
And Branch Line Riser

4. Flexible couplings for drops

Flexible elbow

If dimension is
less than 3 ft (0.9m),
flexible fitting is not
needed.

(A T-connection fitting with


flexible joints can be
substituted for elbow.)

24 in. (610mm) [Paragraph 9.3.2.4(1)]

In-rack sprinkler drops


Flexible Coupling

Drop Supports

24 in. (610mm)
[Paragraph
9.3.2.4(3)]

FIGURE A.9.3.2(b) Detail at Short Riser

FIGURE A.9.3.2.4 Flexible Coupling for Drops

154
Copyright 2011 Shurjoint

Connect with the Best!

Flexible Coupling
24 in.
(610mm)
[Paragraph
9.3.2.4(2)]

www.shurjoint.com

Catalog 2011

5. Seismic Separation Assembly

2 ells
10 in. (254mm)
long nipple D

10 in. (254mm)
long nipple C

Coupling
B

2 ts
8 in.
(203mm)

Fire sprinkler
main

Normal
Position

4 in. (102 mm)

4 in. (102 mm)

Fire
sprinkler
main

Plan

8 in. (203mm)

Longitudinal movement

2 ts
and nipple E

8 in.
(203mm)

Normal
Position

8 in. (203mm)

Vertical
movement

Coupling
Ell
B

A
Ell

Normal
position

Ell
Ell

Elevation

Nipple E
2 ell lengths
8 in. (216mm) for 3 in. (76mm) pipe
7 in. (191mm) for 2 in. (65mm)
pipe

FIGURE A.9.3.3(a) Seismic Separation Assembly. Shown are an 8 in. (203 mm) Separation Crossed by Pipes up to 4 in. (102mm) in Nominal Diameter. For other separation
distances and pipe sizes, lengths and distances should be modified proportionally.

6. Earthquake protection for sprinkler piping

4 in.
(102 mm)

8 in.
(203mm)

Lateral movement

Horizontal Views

7. Typical Location of Bracing on a Looped System

40 ft

40 ft

(12 m)

(12 m)

Longitudinal brace
(two-way)

A
No bracing

B
Lateral brace
(two-way)
Longitudinal brace
(two-way)

B
F

E
D

Building 1

FIGURE A.9.3.5.6 (a)

Building 2

A Four-way brace at riser


B Lateral brace
C Lateral brace
D Short drop [Figure A.9.3.2(b)]
E Couplings at wall penetration
F Longitudinal brace

Connect with the Best!

Four-way brace

FIRURE A.9.3.5.6 (d)


Typical Location of Bracing on a Looped System.

Systems having more flexible couplings than required above shall


be provided with additional sway bracing. A lateral brace shall be
provided within 24 (600mm) of every other coupling unless pipes are
supported by rods less than 6 (152mm) long from the ceiling or by
U-type hooks underside of the structural element. (NFPA 13 2007
9.3.2. & 9.3.5.)

www.shurjoint.com

155
Copyright 2011 Shurjoint

Catalog 2011

HVAC, St. Marys Hospital,


Seoul, Korea

HVAC, Praktiker warehouse,


Iraklion Krete, Greece

HVAC, Microsoft facility, Puerto Rico

156
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

Temporary Speed Skating Rink, Halifax, Nova Scotia, Canada

Holiday Inn Swimming Pool Pump Room, Las Vegas, NV

HVAC, Taichung City Government


Office, Taichung, Taiwan

Westside Regional Wastewater Treatment, BC, Canada


HVAC, Tamkang University, Lanyang, Taiwan

Connect with the Best!

www.shurjoint.com

157
Copyright 2011 Shurjoint

Catalog 2011

East Side CSO tunnel boring project,


Portland, OR

Ik-san E-Mart, Seoul, Korea

Manifold connections, Rain for Rent, Las Vegas, NV

Water treatment plant, Ouray, UT

158
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

HVAC, King Abudullah Financial District, KSA

Fire Protection Systems, Dubai Metro, UAE

Ski Dome glycol pipelines, Dubai, UAE

Fire Protection Systems, Tamkang University, Lanyang, Taiwan

Connect with the Best!

HVAC, Seven Stars Technology Building, Taipei, Taiwan

www.shurjoint.com

159
Copyright 2011 Shurjoint

Catalog 2011

Terms and Conditions


Controlling Provisions:

These terms and conditions shall control with respect to any and all

purchase orders or sales of Shurjoint products.

No alteration, modification or waiver of these terms and conditions


whether on the customer's purchase order or otherwise shall be valid

Weights:

All weights are approximate and subject to change without notice.


Always specify gasket grade when ordering and double check the
gasket grade received to be sure it is suited for the service intended.

unless the alteration, modification or waiver is specifically accepted in

Shurjoint reserves the right to change or modify product designs,

Inc.

incurring obligation. Prices and Terms and Conditions of Sale are

writing by an authorized representative of Shurjoint Piping Products,

specifications and/or standard equipment without notice and without


subject to change without notice.

Shipping Terms:

All orders are quoted F.O.B. shipping point unless otherwise agreed
upon in writing.

Warranty:

We warrant all Shurjoint products to be free from defects in

Orders are accepted subject to approval by our Head Office and


Credit Department and are contingent upon acts of God, war,
civil unrest or disturbance, strikes, labor difficulties, governmental
regulations or rulings, delays of carriers (land, air or ocean), inability
to obtain materials, accidents or any other cause beyond our control.
Shipping dates are estimated, and we will do our best to ship within
the time estimated. We cannot guarantee shipping dates, and in
the event of a production or shipment delay, we reserve the right to
change the estimated shipping date. Under no circumstances shall
Shurjoint be liable for damages of any kind, including but not limited

to incidental or consequential damages for lost sales or profits or


liquidated damages, directly or indirectly arising from delays or failure
to meet shipping dates.

materials and workmanship under normal conditions of use and


service. Our obligation under this warranty is limited to repairing
or replacing at our option at our factory or designated facility any
product which shall within 10 years after delivery to the original
buyer be returned with transportation charges prepaid, and which
our examination and inspection shall show to our satisfaction to have
been defective.
This warranty is made expressly in lieu of any other warranties,
express or implied, including any implied warranty of merchantability
or fitness for a particular purpose. The buyer's sole and exclusive
remedy shall be for the replacement or repair of defective products
as provided herein. The buyer agrees that no other remedy
(including but not limited to), incidental or consequential damages
for lost profits, lost sales, injury to person or property or any other

Orders accepted cannot be changed or cancelled without our written


consent.

incidental or consequential loss shall be available to him/her.


Shurjoint neither assumes nor authorizes any person to assume

Orders for special (non-standard) goods may not be cancelled, nor


will we accept return of these goods for credit.

Claims For Shortages:

All claims for shortages must be made within 10 days of receipt of


goods. Our responsibility ceases when the goods are delivered to
the carrier in good condition. Carriers are responsible for goods lost,
damaged or delayed in transit. For your own protection have the
transportation company's agent verify any damage, shortage or delay
and note them on the freight bill over his/her signature.

for it any other liability in connection with the sale of such products.

Items purchased by Shurjoint and resold will have the original

equipment manufacturers warranty extended to Shurjoint customers


where applicable.
This warranty shall not apply to any product which has been
the subject to misuse, negligence or accident, which has been
repaired or altered in any manner outside of Shurjoint's factory or
designated facility or which has been used in a manner contrary to
Shurjoint's instructions, recommendations or generally accepted
practices. Shurjoint shall not be responsible for design errors due
to inaccurate or incomplete information supplied by the buyer or his
representatives. (Effective July 1, 1998)

160
Copyright 2011 Shurjoint

Connect with the Best!

www.shurjoint.com

Catalog 2011

Index
Model No.

Page No.

49 . . . . . . . . . . . . . . . . . . . . . 30
55 . . . . . . . . . . . . . . . . . . . . . 51
56 . . . . . . . . . . . . . . . . . . . . . 51
57 . . . . . . . . . . . . . . . . . . . . . 55
58 . . . . . . . . . . . . . . . . . . . . . 55
59 . . . . . . . . . . . . . . . . . . . . . 55
71 . . . . . . . . . . . . . . . . . . . . . 97
79 . . . . . . . . . . . . . . . . . . . . 110
651 . . . . . . . . . . . . . . . . . . . . 85
723 . . . . . . . . . . . . . . . . . . . . 38
726 . . . . . . . . . . . . . . . . . . . . 88
728 . . . . . . . . . . . . . . . . . . . . 89
811 . . . . . . . . . . . . . . . . . . . . . 93
812 . . . . . . . . . . . . . . . . . . . . 93
813 . . . . . . . . . . . . . . . . . . . . 93
814 . . . . . . . . . . . . . . . . . . . . 93
815 . . . . . . . . . . . . . . . . . . . . 94
815 . . . . . . . . . . . . . . . . . . . . 93
816 . . . . . . . . . . . . . . . . . . . . 94
817 . . . . . . . . . . . . . . . . . . . . 94
818 . . . . . . . . . . . . . . . . . . . . 94
819 . . . . . . . . . . . . . . . . . . . . 95
820 . . . . . . . . . . . . . . . . . . . . 95
825 . . . . . . . . . . . . . . . . . . . . 95
827 . . . . . . . . . . . . . . . . . . . . 95
830 . . . . . . . . . . . . . . . . . . . . 96
831 . . . . . . . . . . . . . . . . . . . . 95
832 . . . . . . . . . . . . . . . . . . . . 95
841 . . . . . . . . . . . . . . . . . . . . 96
850 . . . . . . . . . . . . . . . . . . . . 52
851 . . . . . . . . . . . . . . . . . . . . 52
853 . . . . . . . . . . . . . . . . . . . . 52
899 . . . . . . . . . . . . . . . . . . . . 51
901 . . . . . . . . . . . . . . . . . . . . 49
903 . . . . . . . . . . . . . . . . . . . . 49
7041 . . . . . . . . . . . . . . . . . . . 28
7043 . . . . . . . . . . . . . . . . . . . 30
7110 . . . . . . . . . . . . . . . . . . . . 43
7111 . . . . . . . . . . . . . . . . . . . . 43
7112 . . . . . . . . . . . . . . . . . . . . 43
7113 . . . . . . . . . . . . . . . . . . . . 43
7114 . . . . . . . . . . . . . . . . . . . . 53
7120 . . . . . . . . . . . . . . . . . . . 44
7121 . . . . . . . . . . . . . . . . . . . 45
7122 . . . . . . . . . . . . . . . . . . . 53
7125 . . . . . . . . . . . . . . . . . . . 50
7127 . . . . . . . . . . . . . . . . . . . 49
7130 . . . . . . . . . . . . . . . . . . . 44
7133 . . . . . . . . . . . . . . . . . . . 53
7135 . . . . . . . . . . . . . . . . . . . 44
7137 . . . . . . . . . . . . . . . . . . . 48
7150 . . . . . . . . . . . . . . . . . . . 46
7151 . . . . . . . . . . . . . . . . . . . 46

Model No.

Page No.

7160 . . . . . . . . . . . . . . . . . . . 47
7170 . . . . . . . . . . . . . . . . . . . 32
7180 . . . . . . . . . . . . . . . . . . . 31
7181 . . . . . . . . . . . . . . . . . . . 31
7705 . . . . . . . . . . . . . . . . . . . 18
7706 . . . . . . . . . . . . . . . . . . . 22
7707 . . . . . . . . . . . . . . . . . . . 19
7721 . . . . . . . . . . . . . . . . . . . 35
7722 . . . . . . . . . . . . . . . . . . . 37
10EP . . . . . . . . . . . . . . . . . . . 58
11EP . . . . . . . . . . . . . . . . . . . 58
20EP . . . . . . . . . . . . . . . . . . . 58
22EP . . . . . . . . . . . . . . . . . . . 58
35EP . . . . . . . . . . . . . . . . . . . 58
650N . . . . . . . . . . . . . . . . . . . 84
7110-B . . . . . . . . . . . . . . . . . . 48
7110DR . . . . . . . . . . . . . . . . . 49
7110LR . . . . . . . . . . . . . . . . . 48
7111LR . . . . . . . . . . . . . . . . . 48
7112G . . . . . . . . . . . . . . . . . . 48
7150F . . . . . . . . . . . . . . . . . . 50
7150M . . . . . . . . . . . . . . . . . . 50
7160H . . . . . . . . . . . . . . . . . . 47
7160P . . . . . . . . . . . . . . . . . . 47
7160T . . . . . . . . . . . . . . . . . . 47
725F . . . . . . . . . . . . . . . . . . . 86
72C . . . . . . . . . . . . . . . . . . . . 98
72R . . . . . . . . . . . . . . . . . . . . 98
7706-T . . . . . . . . . . . . . . . . . . 25
7707L . . . . . . . . . . . . . . . . . . 21
7707N . . . . . . . . . . . . . . . . . . 20
7771-T . . . . . . . . . . . . . . . . . . 25
A10 . . . . . . . . . . . . . . . . . . . 133
A10R . . . . . . . . . . . . . . . . . . 134
A11 . . . . . . . . . . . . . . . . . . . 133
A12 . . . . . . . . . . . . . . . . . . . 133
A13 . . . . . . . . . . . . . . . . . . . 133
A20 . . . . . . . . . . . . . . . . . . . 134
A25 . . . . . . . . . . . . . . . . . . . 134
A50 . . . . . . . . . . . . . . . . . . . 134
A505 . . . . . . . . . . . . . . . . . . 131
A507 . . . . . . . . . . . . . . . . . . 132
A512 . . . . . . . . . . . . . . . . . . 132
A60 . . . . . . . . . . . . . . . . . . . 133
B20 . . . . . . . . . . . . . . . . . . . . 96
B24 . . . . . . . . . . . . . . . . . . . . 96
C10 . . . . . . . . . . . . . . . . . . . 122
C10-W . . . . . . . . . . . . . . . . . 122
C11 . . . . . . . . . . . . . . . . . . . 122
C11-W . . . . . . . . . . . . . . . . . 122
C20 . . . . . . . . . . . . . . . . . . . 122
C20-W . . . . . . . . . . . . . . . . . 122
C21 . . . . . . . . . . . . . . . . . . . 123

Connect with the Best!

Model No.

Page No.

C26 . . . . . . . . . . . . . . . . . . . 123
C305 . . . . . . . . . . . . . . . . . . 119
C306 . . . . . . . . . . . . . . . . . . 120
C307 . . . . . . . . . . . . . . . . . . 121
C341 . . . . . . . . . . . . . . . . . . 121
C50 . . . . . . . . . . . . . . . . . . . 123
C52 . . . . . . . . . . . . . . . . . . . 124
C55 . . . . . . . . . . . . . . . . . . . 124
C55T . . . . . . . . . . . . . . . . . . 125
C60 . . . . . . . . . . . . . . . . . . . 122
C-7 . . . . . . . . . . . . . . . . . . . . . 24
C723 . . . . . . . . . . . . . . . . . . 126
C726 . . . . . . . . . . . . . . . . . . 127
DE30-GG . . . . . . . . . . . . . . . 125
G-28 . . . . . . . . . . . . . . . . . . . 23
H305 . . . . . . . . . . . . . . . . . . 113
H307 . . . . . . . . . . . . . . . . . . 114
H312 . . . . . . . . . . . . . . . . . . 115
L11-3D . . . . . . . . . . . . . . . . . . 56
L11-5D . . . . . . . . . . . . . . . . . . 57
L11-6D . . . . . . . . . . . . . . . . . . 57
L22-3D . . . . . . . . . . . . . . . . . 56
L22-5D . . . . . . . . . . . . . . . . . 57
L22-6D . . . . . . . . . . . . . . . . . 57
L30-3D . . . . . . . . . . . . . . . . . 56
L30-5D . . . . . . . . . . . . . . . . . 57
L30-6D . . . . . . . . . . . . . . . . . 57
L45-3D . . . . . . . . . . . . . . . . . 56
L45-5D . . . . . . . . . . . . . . . . . 57
L45-6D . . . . . . . . . . . . . . . . . 57
L60-3D . . . . . . . . . . . . . . . . . 56
L60-5D . . . . . . . . . . . . . . . . . 57
L60-6D . . . . . . . . . . . . . . . . . 57
L90-3D . . . . . . . . . . . . . . . . . 56
L90-5D . . . . . . . . . . . . . . . . . 57
L90-6D . . . . . . . . . . . . . . . . . 57
M21 . . . . . . . . . . . . . . . . . . . . 34
M22 . . . . . . . . . . . . . . . . . . . . 36
M-7 . . . . . . . . . . . . . . . . . . . . 14
R-88 . . . . . . . . . . . . . . . . . . . 101
R-88 . . . . . . . . . . . . . . . . . . . 103
R88N . . . . . . . . . . . . . . . . . . 102
RCV . . . . . . . . . . . . . . . . . . . . 90
RH-1000 . . . . . . . . . . . . . . . 104
RJ-10 . . . . . . . . . . . . . . . . . . 106
RJ-11 . . . . . . . . . . . . . . . . . . 106
RJ-20 . . . . . . . . . . . . . . . . . . 106
RJ-21 . . . . . . . . . . . . . . . . . . 107
RJ-50 . . . . . . . . . . . . . . . . . . 107
RJ-51 . . . . . . . . . . . . . . . . . . 107
RJ-60 . . . . . . . . . . . . . . . . . . 106
RJ-70 . . . . . . . . . . . . . . . . . . 107
RX-3000 . . . . . . . . . . . . . . . 104

Model No.

Page No.

RX-3770 . . . . . . . . . . . . . . . 105
S35 . . . . . . . . . . . . . . . . . . . 109
SD-28 . . . . . . . . . . . . . . . . . 109
SJ-200 . . . . . . . . . . . . . . . . . . 77
SJ-300F . . . . . . . . . . . . . . . . . 79
SJ-300N . . . . . . . . . . . . . . . . 78
SJ-400 . . . . . . . . . . . . . . . . . . 74
SJ-500L . . . . . . . . . . . . . . . . . 80
SJ-500W . . . . . . . . . . . . . . . . 80
SJ-600L . . . . . . . . . . . . . . . . . 73
SJ-600W . . . . . . . . . . . . . . . . 73
SJ-900 . . . . . . . . . . . . . . . . . . 81
SJ-915 . . . . . . . . . . . . . . . . . . 82
SJ-930 . . . . . . . . . . . . . . . . . . 83
SJ-C300 . . . . . . . . . . . . . . . 128
SS-10 . . . . . . . . . . . . . . . . . . 68
SS-11 . . . . . . . . . . . . . . . . . . . 68
SS-1200 . . . . . . . . . . . . . . . . 66
SS-20 . . . . . . . . . . . . . . . . . . 68
SS-21 . . . . . . . . . . . . . . . . . . 69
SS-28 . . . . . . . . . . . . . . . . . . 67
SS-41 . . . . . . . . . . . . . . . . . . 71
SS-5 . . . . . . . . . . . . . . . . . . . 61
SS-50 . . . . . . . . . . . . . . . . . . 69
SS-60 . . . . . . . . . . . . . . . . . . 68
SS-7 . . . . . . . . . . . . . . . . . . . 62
SS-723 . . . . . . . . . . . . . . . . . 72
SS-726 . . . . . . . . . . . . . . . . . 72
SS-7X . . . . . . . . . . . . . . . . . . 63
SS-8 . . . . . . . . . . . . . . . . . . . 64
SS-80 . . . . . . . . . . . . . . . . . . 71
SS-8X . . . . . . . . . . . . . . . . . . 65
W110 . . . . . . . . . . . . . . . . . . . 54
W110LR . . . . . . . . . . . . . . . . 54
W111LR . . . . . . . . . . . . . . . . . 54
W120 . . . . . . . . . . . . . . . . . . . 54
W121 . . . . . . . . . . . . . . . . . . . 54
W150 . . . . . . . . . . . . . . . . . . . 55
W151 . . . . . . . . . . . . . . . . . . . 55
W160 . . . . . . . . . . . . . . . . . . . 54
WS-10 . . . . . . . . . . . . . . . . . . 70
WS-10L . . . . . . . . . . . . . . . . . 70
WS-11 . . . . . . . . . . . . . . . . . . 70
WS-20 . . . . . . . . . . . . . . . . . . 70
WS-21 . . . . . . . . . . . . . . . . . . 70
WS-50 . . . . . . . . . . . . . . . . . . 70
WS-60 . . . . . . . . . . . . . . . . . . 70
XH-1000 . . . . . . . . . . . . . . . . 17
XH-70EP . . . . . . . . . . . . . . . . 26
Z05 . . . . . . . . . . . . . . . . . . . . 15
Z07 . . . . . . . . . . . . . . . . . . . . 16

www.shurjoint.com

161
Copyright 2011 Shurjoint

You might also like