You are on page 1of 10

6/25/2014 Camshaft and Valvetrain Basics

http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 1/10
From: EPI Inc. Contact: tech@epi-eng.com


Race Engine
Technology
Magazine
CURENT ISSUE
Contents BACK
ISSUE Summaries
SUBSCRIBE


Wednesday, June 25th, 2014 01/25/2013
- The Basics of Valvetrain Technology -
Cams, Lifters, Pushrods, Rockers, Springs, Retainers, Valves
BACKGROUND
As we presented in a previous section, the flow capability of the cylinder heads, intake passages and exhaust
passages in a 4-stroke ("Four-Cycle") engine is extremely important to engine performance. However, the
motion of the valves relative to the position and velocity of the piston is perhaps even more important in
determining the power a given configuration can produce.
The motion of a valve is generated by the shape of the cam lobe, which pushes on a cam follower of some
sort, which then connects to the valve by a variety of different mechanisms. The system in which we are most
interested here is the cam follower in a bore, driving a pushrod which moves a pivoted lever ("rocker arm")
which presses on the tip of the valve and imparts reciprocating motion to open the valve. In this system, closing
the valve is done by the valve spring. The following picture (courtesy of Ford Motor Company ) shows the
components in this system.
Figure 1: Pushrod Engine Cross Section (Ford Smallblock)
The system that is the focus of this article, the pushrod / rocker-arm / overhead valve mechanism, has been
used in domestic automotive engines since the early part of the 20th century, because of the demonstrably-
superior breathing capability provided by "valve-in-head" designs compared to the prevalent "side-valve" or
"flathead" engine design in which the valves are in the engine block alongside the cylinders. This system saw
early mass production in the Chevrolet inline-4 that was produced until 1936, replaced by the Chevrolet inline
6 starting in 1935. The system began to dominate domestic production automotive engines beginning with the
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 2/10
1949 Oldsmobile "Rocket" 324 cubic inch V8. Because of its inherent performance and cost effectiveness, the
pushrod / rocker arm OHV system has continued to be refined, and is still used in many contemporary (early
21st century) engines. One of the most noteworthy is the prolific family of GM 4th-generation smallblock V8
engines (the "LS" family).
Note that there are numerous other systems, ranging from the primitive "side valve" engines in which the cam
operates a follower in a bore, which then directly operates the valve, to a variety of different overhead cam
configurations which operate the valves either directly from the cam follower ("direct-acting") or by means of
any of several different rocker arm implementations, and reaches extreme complexity with systems in which
there is one cam profile to open the valve and a different complimentary cam profile which directly closes the
valve, eliminating the need for a valve spring (known as "desmodromic" systems).
Here is a more thorough look into the details of this pushrod-OHV system. In a 4-stroke engine, the
crankshaft drives the camshaft at 1/2 crankshaft speed (obviously, since each valve opens and closes once for
evvery two rotations of the crankshaft) . The camshaft typically contains one cam lobe for each valve in the
engine, although that is not necessarily the case. (For example, in opposed-layout engines such as the VW-
Porsche horizontally-opposed pushrod engines, two intake valves, one on each side of the engine, are
operated by a single lobe driving two different followers.) For convenience, Figure 1 is reproduced below
in order to assist the following descriptions.
Figure 1 (repeat): Pushrod Engine Cross Section (Ford Smallblock)
FUNDAMENTALS
As each cam lobe rotates, it contacts the cam follower (aka "lifter", aka "tappet") and drives the follower
away from the camshaft rotational axis. The cam follower, which is constrained by the bore in which it moves,
produces a linear motion along the bore axis. That linear motion of the follower is transmitted to one end of the
pushrod. The other end of the pushrod moves in a somewhat less predictable manner, constrained by the
pushrod socket in the rocker arm, but also disturbed by pushrod deflections, both compressive and flexural,
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 3/10
which vary with the forces and excitations applied to the pushrod. The rocker arm rotates about its pivot point
(typically either a shaft or a semi-ball on a stud), and the other end of the rocker arm contacts the tip of the
valve stem and causes the valve to move along the axis of the bore ("valve guide") in which it rides.
It is sometimes believed that the cam lobe is only able to directly control the opening portion of the valve
motion, by pushing the follower away from it, and that the valvespring controls the closing half of the cycle.
That view is very incorrect. In actuality, the cam lobe and the valvespring, when operating correctly, work in
close harmony throughout the opening-closing cycle to produce the desired valve motion. The cam lobe
provides the operating force during approximately tie first half aof the opening cycle and the last half of the
closing cycle, and, the valve spring provides the operating forces throughout approximately the last half of the
opening cycle and the first half of the closing cycle. This concept will be made much more clear later in the
discussion.
An excellent example of the influence which cam lobe profiles have on performance is in the evolution of what
are known as "restricted" race engines. These engines are "restricted" with respect to the modifications that can
be done to them, in an effort to limit the power, and therefore to limit (in theory, but not in practice) the cost
of the engines.
The most common engine in this category is an iron-block 355-cubic inch small-block Chevy (SBC) V8,
which is commonly limited to stock (unported, unmodified) production cast-iron cylinder heads and intake
manifolds. In certain classes these engines are limited to a single two-barrel carburetor which, in stock form,
can't flow more than 500 CFM of air at a pressure differential of 3" of water. This configuration represents the
very incarnation of a "flow-limited" engine.
In the early development of these engines, the max power we could coax from these engines was in the 425
HP neighborhood (which, in itself, is impressive). Since approximately 2006, we have passed 500 HP and are
continually, but slowly, approaching 525, while using essentially the same heads and manifolds (as specified by
the NASCAR rules for these engines). All that development costs MONEY, and the cost of these engines is
prohibitively high for many racers.
One major factor in that progress has been the development of ever-more aggressive cam lobe profiles, which
are optimized to this particular flow-limited configuration. Of course, as you might expect, these cam profiles
are very hard on the valve train components, so the successful operation of the system depends on the
development of ever-more sophisticated valvetrain components. Here, we will attempt to explain why, and
how different requirements can be met through the various compromises taken in cam lobe design.
Given the inherent limitations of that layout at high engine speeds, it is a huge tribute to the skills and knowledge
of the NASCAR engine builders at the "Cup" level that they have succeeded in making this type of engine (358
cubic inch, flat-tappet, pushrod / rocker-arm, two-valve-per-cylinder, normally aspirated, single-
carburetor V8) operate reliably at over 9,500 RPM and produce unheard-of power levels (over 860 HP as
of 2012) for hours at a time. (For more insight into these amazing engines, CLICK HERE.)
The reason we focus on this configuration is that, with respect to aircraft engines, we think this pushrod /
rocker-arm system is the best solution to the compromises required to achieve a good aircraft engine: (a)
maximum power per pound of engine weight, combined with (b) reasonable piston speeds and valvetrain
stresses for maximum reliability. We will provide support for that argument as the article progresses.
There is little question that an engine with a double-overhead-cam (DOHC) configuration and four valves per
cylinder will produce more power per cubic inch of displacement, but that superiority occurs because of the
superior breathing properties that a 4-valve configuration provides at high engine speeds and the more accurate
valve motion that an overhead cam configuration provides at high engine speeds. However, reliability
constraints have historically opposed the use of high engine speeds in aircraft engines, so the additional weight
of the DOHC configuration tends to favor the pushrod / rocker arm layout.
CAM FOLLOWER MOTION
Basic camshaft events (valve opening, closing and maximum lift) are commonly referenced to crankshaft
position, because the motion of the valves needs to be studied relative to the position (and velocity) of the
piston. For example, a typical intake lobe might begin to open the valve at 20 degrees Before Top Center
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 4/10
(BTC, before the piston reaches the exact top of its stroke) and to finish closing the valve at 50 degrees after
Bottom Dead Center (BDC). And yes, the piston is still moving upward when the intake valve opens and is
also moving upward when the intake valve closes. This, and other apparent anomalies, are related to the
dynamics of air motion, and will be discussed later.
Here is a graph showing the axial motion of the cam followers for one cylinder of a two-valve (one intake, one
exhaust) engine as a function of camshaft rotation. The red trace is the exhaust follower travel and the blue
trace is the intake follower travel. Note that the rotation axis is plotted in degrees of crankshaft rotation (which
is twice the camshaft rotation, since the camshaft spins at half crankshaft speed in a 4-stroke engine). The
lobes pictured here provide a maximum lobe lift of roughly 0.420 inches. That lobe lift, operating through a
nominal rocker ratio of 1.6, will theoretically produce nearly 0.675 of valve lift.
Figure 2: Cam Follower Position vs. Crankshaft Position
The commonly-quoted specifications for cam lobes are lift, duration, overlap, and lobe separation. The "Lift"
spec is the maximum amount of travel the cam follower experiences as the cam lobe rotates under it. The "zero
lift point" can be defined as the lift when the lobe is rotated 180 degrees from its maximum lift point, when the
cam follower is said to be "on the base circle" (the constant-radius portion) of the lobe.
"Duration" is the number of crankshaft degrees of rotation during which the cam follower lift is greater than
some specified value. Without knowing the lobe-lift value at which a duration is measured, the duration number
is meaningless. That is because the cam lobe contains slow-motion ramps at the beginning and end of the lift
period (detailed later) to take up clearances and to get the parts into motion gradually. The properties of those
ramps can vary dramatically based on the intended use of the particular lobe design and the preferences of the
lobe designer, so a cam specification that rates duration during those slow liftoff and landing periods is simply
deceptive.
It has become an accepted industry practice (initiated by Harvey Crane back in the 1960's) to specify lobe
duration as the number of degrees between the opening and closing points at which the lifter is 0.050 off the
base circle.
Overlap, referring to Figure 2 above, is the number of degrees of crankshaft rotation during which both valves
are off their seats at the same time, and measured as the number of degrees of crankshaft rotation during which
both lifters are more than some specified distance from the zero-lift point (off base circle). Again, without this
reference number, an overlap spec is essentially worthless. If we use the 0.050 tappet lift reference, the
overlap of the cam shown in Figure 2 is roughly 40 degrees.
Overlap, as we will discuss later, is a very important influence on engine performance. Ed Iskenderian, one of
the early developers of aftermarket camshafts, used to refer to overlap an "the 5th Cycle".
Figure 3 below is an expanded version of the lift profile of the intake lobe shown in Figure 2. The lift axis is
unlabeled, but each graduation on the vertical axis represents 0.050 of lobe lift.
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 5/10
Figure 3: Cam Lobe (Lifter) Motion Profile
As is shown in Figure 3, the lobe begins to move the follower and the valvetrain at about 60 degrees before
Top Dead Center (BTC) and doesn't stop moving the valvetrain until about 95 degrees AFTER Bottom Dead
Center (ABC). However, it is clear that the motion (the steepness of the lift profile) closest to the opening and
closing points is relatively slow by comparison to the motion at, for example, the TDC point.
Now, as you might expect, it can be difficult to determine on an actual engine, with sufficient accuracy, the
exact crankshaft position when a valve begins to open or close, because of the gradualness of the motion at
those points. And, the exact value of the crankshaft position relative to opening or closing points can be
dramatically changed by changes in static clearance between the valve and the mechanism which moves it
(rocker arm or cam follower).
That situation is not much improved if, instead of valve motion, you use lifter motion to determine these points.
The reason is because a cam lobe does not start the lifter moving suddenly. Each cam lobe includes opening
and closing "ramps" which allow the cam to start and to end the lifter motion in a gradual fashion. Therefore,
the contemporary method of specifying cam lobe events is to state the number of degrees before and after
TDC / BDC at which the lifter has moved to a distance of 0.050" from it's "zero-motion position". The zero
motion position is measured when the follower is on the zero-lift portion of the lobe surface (known as the
"base circle" or "heel" of the lobe) and the maximum lift portion of the cam lobe is opposite (180 away from)
the lifter.
The two dark vertical lines in Figure 3 (to the left of TDC and to the right of BDC) show the 0.050 lift points
on the opening and closing profile, where the steepness of the lift profile has increased quite a bit. Those 0.050
lift points occur at 20 degrees BTDC and 58 degrees ATDC.
With reference to the customary 0.050 lobe lift points, the duration of this lobe is 258 degrees (20 degrees
BTDC, plus 180 degrees from TDC to BDC, plus 58 degrees ABDC). With respect to the effect on engine
performance, that 0.050 duration figure is far more meaningful than what some manufacturers would advertise
as the duration of that lobe (336 degrees, taken at the 0.003 lift points).
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 6/10
The lobe "centerline" (the point of max lobe lift, shown by the green line) is located at 105 degrees after TDC.
In this example, the centerline occurs essentially midway between the opening and closing events. However,
that is not necessarily the case. We now frequently use lobes with lift profiles that are asymmetric about the
centerline in order to tailor opening and closing rates for various purposes.
The next curve (Figure 4) shows the same lift profile (blue) as was shown in Figure 3 above, but something
has been added. The red curve represents the velocity of the follower with respect to the rotation of the cam,
in units of inches per degree (or mm per degree if you are metrificated)..
Figure 4: Cam Lobe (Lifter) Motion and Velocity Profiles

The next curve shows the cam follower acceleration (black) and velocity (red) which corresponds to the cam
follower lift curve (blue).
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 7/10
Figure 5: Cam Lobe (Lifter) Motion, Velocity and Acceleration Profiles
The cam lobe provides the "programmed" cam follower motion throughout the cycle. During approximately the
first 1/4 of the cycle, the lobe also provides the force that accelerates the valvetrain components (cam follower,
pushrod, rocker arm, valve, keeper, retainer and spring) in the opening direction. During the last approximately
1/4 of the cycle, the cam lobe provides the force that decerates the fast-moving valvetrain components to a
stop and allows the valve to gently close on the valve seat. During the middle half of the cycle, the valvespring
provides the forces necessary to decelerate the components to a stop at maximum valve lift, and to accelerate
those components from that momentary stop to a high velocity back in the direction of valve closing.

The following graph shows the lifter motion caused by two different cam lobes, both of which have the same
opening and closing specifications (as measured by the 0.050" travel points of the lifter). These plots are
known as "lift curves". The horizontal axis is crankshaft rotation, referenced to TDC and BDC.
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 8/10
Figure 6: Cam Lobe (Lifter) Motion Profile Comparison
As you can see, both lift curves look fairly smooth. However, there is a substantial difference between the
amount of force and vibration each of these two lobes impose on the remainder of the valvetrain they operate.
Those differences can only be seen by examining the curves which show the velocity and the acceleration these
lobes generate.
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 9/10
Figure 7: Cam Lobe (Lifter) Motion, Velocity and Acceleration Comparisons
More to come:
Curves: greater explanations and depth about preceding curves
Cam Followers: flat-cylindrical, flat-mushroom, radius, roller, rocker-arm
Pushrods: cylindrical, tapered, euler-column, stiffness, mass
Rocker Arms: shaft, pedestal, flat-end, roller end, needle bearing, plain bearing, spherical pivot, mmoi
Springs: single, double, triple, rev-kit, round wire, ovate wire, rate, res freq, mass
Excitations: lift, acceleration, fourier content of curves
Forces and Deflections: acceleration, vibration , resonance points
<< Return to: Contents Go to: Top of Page Next Subject: Hydrodynamic Bearings >>
6/25/2014 Camshaft and Valvetrain Basics
http://www.epi-eng.com/piston_engine_technology/camshaft_basics.htm 10/10
HomeAbout EPISite MapContact Us
DISCLAIMER: EPI Inc. and the contributors and reviewers of the material presented on this website have confidence that every
effort has been made to ensure the accuracy and completeness of the information available, but we cannot be responsible for any
errors or omissions. Your use of the website and any of the available information indicates your understanding and acceptance of
these terms. EPI Inc. is not liable to any party for any direct, indirect, special, or consequential damages resulting from use of any
information on this website.
Copyright 2012 EPI Inc, All Rights Reserved

You might also like