Firmware was changed to continuously update the enabling values. If the excitation bit is toggled from a disabled state to an enabled state after the change to either limit, the product operates to the new values.
Firmware was changed to continuously update the enabling values. If the excitation bit is toggled from a disabled state to an enabled state after the change to either limit, the product operates to the new values.
Firmware was changed to continuously update the enabling values. If the excitation bit is toggled from a disabled state to an enabled state after the change to either limit, the product operates to the new values.
Catalog Number 1407-CGCM Firmware Revision 4.11 The following changes were made to the Combination Generator Control Module firmware. Corrected Anomalies CORRECTED: The Under-Excitation Limit (UEL) and Over-Excitation Limit (OEL), if changed, do not recognize the new value unless followed by a power cycle. The firmware was changed to continuously update the enabling values. If the excitation bit is toggled from a disabled state to an enabled state after the change to either limit, the product operates to the new values. Topic Page Firmware Revision 4.11 1 Firmware Revision 4.09 2 Additional Resources 3 Rockwell Automation Publication 1407-RN001E-EN-P - April 2014 2 Combination Generator Control Module Firmware Revision 4.09 The following changes were made to the Combination Generator Control Module firmware. Enhancements This table highlights changes made in the user manual, publication 1407-UM001G-EN-P. Page numbers refer to the user manual. Known Anomalies The UEL (Under-Excitation Limit) and OEL (Over-Excitation Limit) if changed, do not function when followed by a power cycle. Firmware Revision 4.08 The following changes were made to the Combination Generator Control Module firmware. Enhancements The dual bus potential transformer ratio was improved to allow separate potential transformer and scale ratios to be set when using dual bus operation. Improved current metering for very low and zero current input levels. Corrected the UEL alarm operation. Improved the operation of the five point UEL curve. Topic Page Removed ControlNet tap cables from dimension and front panel layout diagrams 14, 38 ControlNet taps and channel labels are now furnished loose; provided information on fastening to unit 36 Added note on Dead Bus synchronization behavior differences that relate to host firmware revision 61, 97 Added kVAR Hours to table of metering values 65 Updated the Phase Offset Guide table 97 Added information on energy-metering value considerations 139 Changed range of energy preset attributes in Unscheduled Write table 142 Revised description of overcurrent-protection voltage-restraint provision 168 Rockwell Automation Publication 1407-RN001E-EN-P - April 2014 Combination Generator Control Module 3 Additional Resources These documents contain additional information concerning related products from Rockwell Automation. You can view or download publications at http://www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative. Resource Description Combination Generator Control Module User Manual, publication 1407-UM001 Provides information important to the safe and effective use of the Combination Generator Control Module. Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system. Product Certifications website, http://www.ab.com Provides declarations of conformity, certificates, and other certification details. Publication 1407-RN001E-EN-P - April 2014 PN-XXXXXX Supersedes Publication 1407-RN001D-EN-P - April 2011 Copyright 2014 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A. Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support you can find technical and application notes, sample code, and links to software service packs. You can also visit our Support Center at https://rockwellautomation.custhelp.com/ for software updates, support chats and forums, technical information, FAQs, and to sign up for product notification updates. In addition, we offer multiple support programs for installation, configuration, and troubleshooting. For more information, contact your local distributor or Rockwell Automation representative, or visit http://www.rockwellautomation.com/services/online-phone. Installation Assistance If you experience a problem within the first 24 hours of installation, review the information that is contained in this manual. You can contact Customer Support for initial help in getting your product up and running. New Product Satisfaction Return Rockwell Automation tests all of its products to help ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures. Documentation Feedback Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature/. United States or Canada 1.440.646.3434 Outside United States or Canada Use the Worldwide Locator at http://www.rockwellautomation.com/rockwellautomation/support/overview.page, or contact your local Rockwell Automation representative. United States Contact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your distributor to complete the return process. Outside United States Please contact your local Rockwell Automation representative for the return procedure. Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.., Kar Plaza Merkezi E Blok Kat:6 34752 erenky, stanbul, Tel: +90 (216) 5698400