You are on page 1of 70

XC-522

XC-5000

XC-40

Isok net c
Av. Juan Bautista Alberdi 5283 1P
Ciudad Autnoma de Buenos Aires
Tel: +54 11 4684 2232
http://www.siafa.com.ar
ventas@siafa.com.ar

atalog

ISOKINETIC SOURCE SAMPLING EQUIPMENT


isokinetic sampling equipment
Stationary source sampling is conducted to evaluate gas stream
emissions to the atmosphere from stacks, ducts or process exhausts. A pollutants concentration is measured by extracting a known volume from the gas
stream and determining the average stack gas flow rate over the sampling
period. The mass emission rate of each constituent then may be calculated.
In the area of Stack Sampling Methods, there are 3 major categories of testing: Isokinetic Reference Methods, Instrumental Reference Methods (IRM),
and Gaseous Sampling (which includes sampling for mercury).
Obtaining a representative sample of particulate matter from a gas
stream requires a more complex procedure than sampling only for gases.
Particles can be either liquid droplets or solids. Representative sampling
requires that the velocity of the gas/particle mixture passing into the sampling
nozzle must be as close as possible to the velocity of the gas stream in the
stack or duct. When the velocities are the same, the sampling is isokinetic.
During the entire sampling period, the stack velocity must be monitored
constantly and the pumping rate adjusted so that the nozzle intake velocity matches as closely as possible the velocity of the in-stack gas/particle
mixture. In addition, the pumping rate needs to be adjusted for differences
in pressure, temperature and moisture between the stack conditions and the
pump or meter console. The exact steps to conduct this type of sampling
are spelled out in U.S. EPA Reference Method 5. This method also requires
knowledge of U.S. EPA References Methods 1 through 4.
The Apex AutoKineticTM method 5 sampling system offers modular
components that can be arranged and re-arranged to perform multiple U.S.
EPA Reference Methods. Select from manual, digital or automated meter
consoles, as well as a wide range of heated filter and impinger boxes, heavywall glassware with unground o-ring ball joints, probes built to customer
specified lengths, new designs for umbilical cords, and custom modifications
to meet your unique needs. All delivered in a timely manner at a competitive
price.
For over 22 years, Apex Instruments, Inc., has concentrated on
manufacturing equipment designed for use in sampling stationary combustion
sources. Apex Instruments has always been directly involved with the environmental industry, working close with the U.S. EPA. When the Clean Air Act
was enacted in 1990 and hazardous air pollutants were identified for control,
Apex Instruments was at the forefront of product design, method evaluation
and implementation.

ISOKINETIC SAMPLING EQUIPMENT

Meter Consoles............................................ 5 - 11
Sample Pumps ............................................12, 13
Nozzles & Nozzle Accessories ....................... 14, 15
Probes, Liners, Sheaths & Accessories..........16 - 18
Modular Sample Case Assemblies
Filter Ovens, Impinger Cases, Risers.............19 - 21
Glassware, Adapters & Impingers ..................22 - 28
Umbilical Cords, Sample Lines
Method 4, Method 5 ....................................29 - 34
Method 8, Method 17, Method 23
Method 7C & 7D ..........................................35 - 38
Method 26A, Method 29,
Ontario-Hydro ..............................................39 - 41
Method 201A, Cascade Impactor Kit,
Method 202 ..................................................42 - 46
Filter Media, Sample Recovery
Desiccator and Desiccants ........................47 - 51
Silica Gel, Balances
Calibration Weights.....................................52 - 55
Calibration Equipment, Monorails.............56 - 60
XC-522/XC-572 Components List ............61
Appendix.......................................................62-66
Isokinetic Index ............................................67

MERCURY
d
SAMPLING
SYSTEMS & EQUIPMENT

FLOW, PRESSURE & TEMPERATURE

GAS ANALYSIS EQUIPMENT

ACCESSORIES

APPEN IX

IN EX

ISOKINETIC SOURCE SAMPLING EQUIPMENT

CUSTOMER SATISFACTION is guaranteed at APEX INSTRUMENTS.


We back up this commitment with extensive knowledge of our products, good
communication and an excellent customer service history. Our equipment is
designed by experienced stack testers who know what you face when performing
compliance testing.
We encourage you to suggest ideas to improve our equipment. We work closely
with you, over the long term, to provide the best equipment for your needs.
Delivery:
Most orders are shipped within 24 hours of receipt. Please allow extra
time for custom orders. Shipping times vary according to the requested
shipping service. If you have questions about your shipment please
email our shipping management at shipping@apexinst.com.
Return Merchandise Authorization
Customers wishing to return items for service or credit need to contact
our sales associates for an RMA. Contact by email at sales@apexinst.
com or by phone (919) 557-7300 or toll free (800) 882-3214.
Pricing
Prices are published for U.S. customers only. International customers should
contact their local distributor. Prices are in U.S. Dollars, FOB shipping
point, or Ex Works for International orders. Please confirm current prices by
phone, fax or email. Please refer to our price list for a complete list of part
numbers and kit configurations.
Payment
For your convenience, MasterCard, VISA and American Express are
welcome. Company purchase orders are accepted upon credit approval.

62

ISOKINETIC SOURCE SAMPLING EQUIPMENT


isokinetic ource ampling /
ethod 5 and associated methods
Apex Isokinetic Source Sampling Systems are rugged versatile equipment designed for extracting a representative flue gas sample from a source to determine dust and fumes emissions in accordance with many U.S. EPA
Reference Methods as published in CFR 40 Part 60 Appendix A. The Apex Isokinetic Source Sampling System
allows the operator to monitor gas velocities, temperatures, pressures and adjust sample flow rates to obtain a
representative flue gas sample.
The results are often used to prove compliance with existing and applicable regulations. It can also be
used to characterize the gas stream, tune or optimize the process or combustion source, or validate control
processes in place.
Consoles, page 4 - 11

Featuring the XC-5000 AutoKineticTM Sampler


Probes and Liners, page 16 - 18

Glassware, page 22

Nozzles, page 14

Modular Sample
Cases, page 19

Pumps, page 12 - 13

Umbilicals, page 29

Versatile System

esigns for Multiple Methods:

Method 5 - Compact
Method 5 - Flexible
Method 5 - Rigid

Method 17
Method 23
Method 26A

Method 29
Method 201A
Method 202

Isokinetic Testing Requires a Thorough Understanding of the First


Five Test Methods Presented in the CFR 40 Part 60, Appendix A.
Method 1 Determination of Sampling Location and Traverse Points
Method 2 Determination of Stack Gas Velocity and Volumetric Flow Rate
Method 3 Determination of Excess Air and Dry Molecular Weight
Method 4 Determination of Moisture In Stack Gases
Method 5 Determination of Particulate Emissions from Stationary Sources
The Apex Method 5 Source Sampling System can be configured with various accessories and used to
sample a wide range of pollutants, such as metals, halides and halogens, polychlorinated biphenyls
(PCBs), dioxins/furans, polycyclic aromatic hydrocarbons (PAHs), particle size distributions and an
ever-increasing group of pollutants by adaptations of basic test methods. Within our catalog we feature
sampling kits and accessories for the most popular isokinetic methods and pollutants of interest. A list of
featured methods can be found on page 4.

ISOKINETIC SOURCE SAMPLING EQUIPMENT


d

Versatile system designs are available to serve complex and challenging stack testing
locations. The Method 5 System, combined with the appropriate accessories, can be
used to sample a wide range of pollutants, such as dust, metals, polychlorinated biphenyls (PCBs), dioxins/furans, polycyclic aromatic hydrocarbons (PAHs), particle size
distributions and an ever-increasing group of pollutants by adaptations of basic test
methods. Contact our helpful sales staff to configure a system to meet your needs.

Select a meter console that is appropriate for the test method and select a configuration
that suits your specific conditions.

Ch

Choose an external pump that suits your specific conditions and desired flow rates.

Select method specific accessories and kits to complete your system.

FEATURE

Console & Pump

MET O S

Apex Instruments method kits are available for the most popular methods.
After choosing the meter console and sample pump, purchase the kit you
need to conduct the desired method.
M

h d

Determination of Moisture

Determination of Particulate
Emissions from Stationary Sources

OTM-28

Controlled Condensate

17

Particulate by In-stack Filtration

23

Dioxins and Furans

0061

Hexavalent Chromium

Flexible System

Recommended Accessories to Convert M5 Kit to Perform:


M

26A

Hydrogen Halides and Halogens

29

Multiple Metals

201A

PM10 Emissions

202

Condensable Particulate Matter,


PM 2.5

Hy

ASTM-D6784-02 Mercury

Rigid-Set-up

dA

We are never more that a phone call away during normal business hours, and
would be glad to help answer any questions you may have. ours of Operation:
Monday through Friday from 8:00 am, until 5:00 p.m. (EST).
Fax :
Email :
Phone # :

(919) 557-7110
sales@apexinst.com
(919) 557-7300
(800) 882-3214

See Links for Methods on Our Website


See Links for Gas Testing Methods
See Links for Flow Testing Methods

ISOKINETIC SOURCE SAMPLING EQUIPMENT


XC-5000 A

TM

The Apex Instruments XC-5000 AutoKinetic Sampler is designed for conducting US EPA Method 5 and associated
isokinetic methods. Take the worry out of isokinetic calculations and the human error out of data entries recorded by hand.
The new XC-5000 is compatible with your existing Method 5 stack sampling components. Report preparation is streamlined
with accurate data downloadable to files for easy preparation and submission to your regulating agency.
TM

Main Power

Probe
Power

LED
Display

LED
Indicator

XC-5000
AutoKineticTM Sampler
Console with Laptop

External
Connections

Color Coded
Thermocouple
Jacks

Delta H
Calibration

Stainless Steel
Vacuum Pump
Quick Connects

Ethernet Interface

Pump Power
Connection
Stainless Steel
Sample Quick Connect

Stainless Steel
Pitot Quick
Connects

Features

Uses standard Apex Instruments sample train


components (probe, nozzle, heated filter box,
impinger box, etc.)
Maintains isokinetic sampling conditions
without operator assistance

Umbilical Cable
Power Connection

Wireless or Ethernet
Connection Available

XC-5000 Isokinetic Source Sampler


Model

escription

XC-5000

AutoKineticTM Sampler Console, 110V

XC-5000-V

AutoKineticTM SamplerTM Console, 240V

Calculates stack traverse points


Calculates correct nozzle diameter for
site conditions
Stores and displays user entered data
and parameters
Upload and download data files

ultiple- ethod
AutoKineticTM Sampler Console

Performs instantaneous isokinetic


sample flow calculations
Timer alerts operator to move the probe
Alarms indicate when acceptable
conditions are not met
English or metric units selectable

Sample Pump: Accepts standard


method 5 pump assemblies.

ISOKINETIC SOURCE SAMPLING EQUIPMENT

XC-5000 AutoKineticTM Sampler


Console and Laptop

Wireless or Ethernet Connection Available

Features
Uses Standard Apex Instruments Sample
Train Components (Probe, Nozzle, Heated
Filter Box, Impinger Box)
Calculates Stack traverse Points (Method 1)
Stores and Displays User Entered
Data and Parameters
Performs Instantaneous Isokinetic Sample
Flow Calculations & Controls Isokinetic Flow
Timer Alerts Operator to Move the Probe
English or Metric Units

XC-5000 software screen shot.

Specifications
Gas Meter: Model AP25, Precision DGM, 0.7 liters per revolution,
digital gas volume with Internal Quadrature Encoder with 6 digit LCD
display, 1cc resolution.

Optional:
4 channel analog input module for logging external
data (4-20ma, 0-10V, 1-5V).

Temperature Control: Integrated temperature control via the Control


and Data Acquisition Board, probe and oven with solid state relays.

imensions:
23 x 21 x 12 (58 cm x 53 cm x 30.5 cm).

Thermocouple isplay: 7 temperatures displayed simultaneously


on the PC User Interface, F or C, Probe, Stack, Oven, Filter,
Exit, AUX and DGM.

Weight: 39 lbs. (17.7 kg).

Digital Pressure Transducers for


Barometric.

H, and

P +/- 2.5
+/- 63mm

0.01 resolution
0.01 mm resolution

H 0-5
0mm-127mm

0.01 resolutions
0.01mm resolution

Barometric

17.7 inHg 32.5 inHg


450 mmHg 825 mmHg

P (Bi-Directional),

0.01 inHg resolution


0.01m mmHg resolution

Power: 120V / 60 Hz. 220V / 50 Hz (optional).


Console Power Requirements:
120V 15amp max.
Umbilical Connections:
Electrical: 4 conductor circular connector grounded shell.
Sample line: Stainless Steel 1/2 Quick Connector.
Pitot Line: Stainless Steel 1/4 Quick Connectors (optional 3/8).
External pump: Stainless Steel 3/8 Quick Connect.
Thermocouples: Type-K standard size.
Communication:
Wireless and Ethernet.

ISOKINETIC SOURCE SAMPLING EQUIPMENT


I

-M

The XC-500 Series Sampling Console is a rugged, lightweight metering console used to extract gas samples in accordance
with US EPA Method 5 for determining source emissions for dust and fumes. The Apex Isokinetic Source Sampler allows
the operator to monitor gas velocities, temperatures, pressures and adjust sample flow rates to maintain isokinetic sampling
conditions. Comes with digital temperature controllers, a choice between digital or liquid manometers, digital temperature
displays and external pump connections. Stainless steel fittings and quick connects are standard. Units in the XC-500 Series
are available in Standard or Metric units, 110V or 220VAC, optional internal orsat pump.
XC-500 Series Sampling Console features a molded, rugged X-case with side handles for attaching the easy carry strap.
The X-case allows for rear door access. Apex Instruments Isokinetic Sampling Consoles are manufactured to conform to the
construction design criteria and specifications cited in U.S. EPA Method 5, Code of Federal Regulations (40 CFR Part 60)
and APTD-0581 documents. All Apex consoles are calibrated prior to shipping.
Digital Filter and
Probe Temperature
Controllers

Optional
Orsat Pump and
Rotameter

Rugged Custom
Molded X-Case

Temperature
Display

Manometer Quick
Connects

Rocker Switches
with Magnetic
Circuit Breakers

Dual Column
Manometer

Elapsed Timer
Coarse Control
Valve
Vacuum Gauge

Temperature
Selector Switch

Dry Gas Meter


Strap

Color Coded
Thermocouple Jacks

Heavy Duty
Panel Latches

Stainless Steel
Non-Reversible Pump
Quick Connect
(Vaccum)

Manometer Zero
Adjust Knobs
Manometer Level
Adjust

Standard Stainless Steel


Pump Connection
(Pressure)

Standard
Stainless Steel
Sample Quick Connect

Slide Out Front Panel

The meter console has a slide-out


panel for easy access.

Standard
Stainless Steel Pitot
Quick Connects

Rear View

Umbilical
Cable Power
Connection

Removable back panel allows


for quick audits.

Fine Control
Valve

Portable

X-case with sample pump on


portable hand cart. (optional)

ISOKINETIC SOURCE SAMPLING EQUIPMENT

XC-522 Source Sampling Console


The Apex Instruments Model XC-522 is a full featured manual
meter console. The Apex Isokinetic Source Sampling Console
allows the operator to monitor gas velocities, temperatures,
pressures and adjust sample flow rates to maintain isokinetic
sampling conditions. Designed with convenient display layout
for manual data recording.
The Apex Instruments Isokinetic Source Sampling Consoles
are manufactured to conform to the construction design criteria
and specifications cited in U.S. EPA Method 5, Code of Federal
Regulations (40 CFR Part 60) and APTD-0581 documents.

Features:

Low Cost - Manual Console


Easy to Operate and Maintain
Rugged, Lightweight, Stackable Case
Removable 19 Front Panel
Carry Strap for Easy Transport
Non-Reversible Sample Pump Connections
Color Coded Thermocouple Jacks
Bright, Easy-to-Read Temperature Displays
Easy-Leveling Dual Column Manometers
Dry Gas Meter with direct read index
Stainless Steel Quick Connects & Fittings

XC-522 Source Sampler

XC-522 English Units (Cubic Feet, oF)


Model

escription

XC-522

English Meter Console, 120 V/60 Hz

XC-522-V

English Meter Console, 240 V/50 Hz

XC-522-O

English Meter Console with optional Orsat Pump


Assembly, 120 V/60 Hz

XC-522-OV

English Meter Console with optional Orsat Pump


Assembly, 240 V/50 H

Specifications
Gas Meter: Rockwell S110 remanufactured with direct read
index, 0.1 cubic feet/revolution, res. 0.001 cubic feet direct read
analog totalizer with 999.999 cubic feet capacity.

Temperature Controllers for Probe and Oven: 1/32 DIN bright red
LED display, indicating temperature controllers with separate 25 amp
solid state relay, auto-tuning. Standard Type-K jack for input.

Manometer: Dual Inclined/Vertical Manometer for determining


stack velocity and sample flow rate. Inclined Range 0-1.0 H0
with 0.01 divisions. Vertical Range 1-10 HO with 0.1 divisions. Fabricated from solid acrylic, precision bored, accurate to
+/- 1%. Convenient self-sealing chrome plated brass quickconnects with Viton O-Rings. Supplied with plastic plugs for
positive secondary seal.

Vacuum Gauge: Dual Scale Vacuum Gauge, 0-30 Hg / 0-100kPa.

Temperature isplay: Panel mount digital thermometer,


bright red LED display, 1/8 DIN plastic housing, Range -157 to
1999F, with separate 7-channel selector switch.

Sample Pump Connections: 3/8 Quick Connects, Stainless Steel,


non-reversible.
Umbilical Connections: Sample Inlet: Stainless Steel QuickConnect; Pitot Lines: 1/4 (3/8 optional) stainless steel Quick Connect;
Electrical: 4 conductor circular connector; Thermocouples: 6 Type K
inputs, standard size.
Power: 120V/60Hz standard; 240V/50Hz optional
imensions: 23 x 21 x 12 (58 x 53 x 30cm) Panel 19
Weight: 43 lbs (19.5kg)

XC-522 Recommended Accessories


XE-0523 Sample Pump Mounted in U MW
Polyethylene Case

Motor: 1/4 hp, 120/240V 60/50Hz 4.6/2.3 Amp., RPM 1725/1425


Measured Flow: 3.1 cfm@ 1 inch Hg; 1.5 cfm@ 15 inches Hg
Maximum Vacuum: 25.5 inches Hg
Weight: 35 lbs. (16kg)
Sample Pumps are sold separately, Page 12-13

Nomographs & Calculators,


See Accessories Section
Page 29d

ISOKINETIC SOURCE SAMPLING EQUIPMENT


XC-572 Source Sampling Console
The XC-572 Source Sampling Console is the metric version of
the XC-522. It is a full featured, compact, and lightweight Isokinetic Source Sampler. It has all the great features you want and
the reliability you need. Field set up is easy with non-reversible
external pump connections and the industry standard 4-pin
electrical connector. (External sample pump sold separately).
Console allows operators to monitor gas velocities, temperatures, pressures, and sample flow rates for maintaining
isokinetic sampling conditions.

Features:

Precision gas meter with leak check indicator


Low Cost - Manual Console
Easy Operation and Maintenance
Rugged, Lightweight, Stackable Case
Removable 19 Front Panel
Carry Strap for Easy Transport
Non-Reversible Sample Pump Connections
Color Coded Thermocouple Jacks
Bright, Easy-to-Read Temperature Displays
Easy-Leveling Dual Column Manometer
Stainless Steel Quick Connects & Fittings
Convenient Layout for Manual Data Recording

XC-572 Source Sampler

XC-572 Metric Units


Model

escription

XC-572

XC-572 Isokinetic Meter Console, Metric, 120V/60Hz

XC-572-V

XC-572 Isokinetic Meter Console, Metric, 240 V/50 Hz

XC-572-O

XC-572 Isokinetic Meter Console, Metric, with optional


Orsat Pump Assembly, 120V/60Hz

XC-572-OV

XC-572 Isokinetic Meter Console, Metric, with optional


Orsat Pump Assembly, 240 V/50 Hz

Specifications
Gas Meter: AP-25 easy to read numeric index with leak
check wheel, low pressure drop, rated 42 lpm at 15mm
H2O, maximum capacity approx. 70 lpm. Totalizer capacity
9999.9999 cubic meter, resolution 0.1 Liter.
Manometer: Dual Inclined/Vertical Manometer for determining stack velocity and sample flow rate. Inclined Range of
0-26mm H0 with .2mm. Vertical Range of 26-250mm HO
with .2mm. Fabricated from solid acrylic, precision bored,
accurate to +/- 1%. Convenient self-sealing chrome plated
brass quick-connects with Viton O-Rings. Supplied with
plastic plugs for positive secondary seal.
Temperature isplay: Panel mount digital thermometer,
bright red LED display, 1/8 DIN plastic housing. Range -105C
to 1372C, with separate 7-channel selector switch.

Temperature Controllers for Probe and Oven: 1/32 DIN bright red
LED display, indicating temperature controllers with separate 25
amp solid state relay, auto-tuning. Standard Type-K jack for input.
Vacuum Gauge: Dual Scale Vacuum Gauge, 0-30 Hg / 0-100kPa.
Sample Pump Connections: 3/8 Quick Connects, Stainless Steel,
non-reversible.
Umbilical Connections: Sample Inlet: Stainless Steel Quickconnect; Pitot Lines: 1/4 (3/8 optional) Stainless Steel Quick Connect; Electrical: 4 conductor circular connector; Thermocouples: 6
Type K inputs, standard size.
Power: 120V/60Hz standard; 240V/50Hz optional.
imension: 23 x 21 x 12 (58 x 53 x 30cm) Panel 19.
Weight: 40 lbs (18kg)

XC-572 Recommended Accessories


XE- AA Sample Pump Mounted in U MW
Polyethylene Case
Motor: 1/2 hp, 120V/60Hz 5 1/2 Amp
2.9 cfm@ 1 inch Hg; 1.4 cfm@ 15 inches Hg
26.5 inches Hg
Weight: 30 lbs. (14kg)

Low Flow
Adapters,VUA,
See Accessories
Section
Page 18d

Sample Pumps are sold separately, Page 12-13

ISOKINETIC SOURCE SAMPLING EQUIPMENT


XC-563

SOU

Apex Instruments Model 563 Source Sampling Console is the


digital equivalent to the XC-522 and XC-572; featuring an AP25
Dry Gas Meter with optical encoder and digital totalizer. The
console also features differential pressure transducers for P
and H. The temperature controllers, thermometer and timer
all have digital displays.

Features

Precision Gas Meter with LCD Totalizer


Module with Dual Pressure Transducers
Digital Probe Temperature Control/Display
Vacuum Gauge (Dual Scale)
Stainless Steel Quick Connects and Control Valves
Digital Temperature Display (oF or oC) with up
to 6 Type-K Inputs
Non-Reversible External Pump Connections
Removable Front Lid and Back Panel

XC-563 Source Sampler

XC-563 Source Sampler Console

Digital Display for P Velocity Pressure,


and H Orifice Pressure
No Messy Manometer Fluid
Digital Elapsed Timer
Lightweight

Model

escription

XC-563

XC-563 Meter Console, 120V/60Hz

XC-563-V

XC-563 Meter Console, 240V/50Hz

XC-563-O

XC-563 Meter Console, with optional Orsat Pump


Assembly, 120V/60Hz

XC-563-OV

XC-563 Meter Console, with optional Orsat Pump


Assembly, 240V/50Hz

Specifications
Gas Meter: AP25, 0.7 liters per revolution, digital gas volume totalizer with Quadrature Encoder, 8 digit LCD display, 1cc resolution.

Umbilical Connections:

Temperature Control: Digital temperature controllers for probe


and oven 1/32 DIN with solid-state relays.

Sample Line: Stainless Steel 1/2 Quick Connectors.

Temperature isplay: Type-K 3.5 Digit LED display (C is standard


for export). C/F selectable via plastic jumper behind front bezel,
-105C to 1372C range. (-157F to 1999F). Separate 7-channel
TC selector switch. Standard and Metric Units.
igital Pressure Transducers for

+/-2.5 range

0.01 resolution

+/-63mm range

0.1mm resolution

0 - 5 range

0.01 resolution

0 - 127mm range

0.1mm resolution

(Bi-Directional)

udit kit
Audit Kit for Digital Metering Console.
d

Pitot Line: Stainless Steel 1/4 Quick Connectors


(optional 3/8).
External Pump: Stainless Steel 3/8 Quick Connect.
Thermocouples: Type-K Standard Size.
Power: 120V / 60Hz Standard
240V / 50Hz Optional
imensions: 23 x 21 x 12 (58cm x 53cm x 30.5cm)
Weight: 39 lbs. (17.7 kg).
Sample Pump: Accepts Standard Method 5 Pump Assemblies.

S -32

-563

M-M100 - Handheld Meriam Manometer


SYR-30ML-LL - Syringe, Luer Lock Tip,
30ml with 1 ml Increments

10

Electrical: 4 conductor circular connector grounded shell.

SCL-F4 - Plastic Quick-Turn (Luer Lock)


S -32 - 8 x 10 Molded Plastic Case
SYR-30ML-LL

SCL-F4

M-M100

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d4S

The Apex XC-40 Source Sampler Console is a durable, lightweight meter


console ideal for Method 4 (Determination of the Moisture Content of Stack
Gas). The meter console can be used with standard impingers and accessories
to collect moisture for required calculations. This unit heats the stack probe and
with its internal pump pulls 0.75 cfm as required to comply with Method 4.
Method 4 Determination of the Moisture Content of Stack Gas Summary:
Stack gas is extracted at constant rate (less than 21lpm) for a minimum
volume of 600 liters. Moisture is scrubbed from the sample stream and
measured volumetrically or gravimetrically.

Features
Rugged lightweight case with Molded-In Handle
Precision Dry Gas Meter with Digital Display
Minihelic Pressure Gauge

XC-40 Source Sampler

Internal Diaphragm Pump


Digital Temperature Display with
up to 5 Type-K Inputs (F)
All Stainless Steel Fittings and
Control Valves
Digital PID Probe Temperature Controller
Digital Elapsed Timer (hr:min:sec)
Vacuum Gauge (Dual Scale)
Easy Access for Service

Method 4 Source Sampler Console


Model

escription

XC-40

Standard Metering Console with Digital Gas Meter, plus


Digital 8 digit LCD Totalizer. -.001 cu.ft. res. (120V/60Hz)

XC-40-V

Standard Metering Console with Digital Gas Meter, plus


Digital 8 digit LCD Totalizer. -.001 cu.ft. res.(240V/50 Hz)

XC-40M

Metric Metering Console with Digital Gas Meter and a 8


digit Digital LCD Totalizer. 1cc res. (120V/60Hz)

XC-40M-V

Metric Metering Console with Digital Gas Meter and a 8


digit Digital LCD Totalizer. 1cc res. (240V/50 Hz)

Specifications
Gas Meter: Model AP25, 0.7/rev., digital gas volume totalizer,
with Quadrature Encoder, 8 digit LCD Display, 1cc resolution.
Flow Indicator: Mechanical Orifice w/Minihelic Pressure Gauge,
range (0-2) or (0-50MM H2O).

Internal Sample Pump: Single cylinder oil-less pump, long life


diaphrams, 1/8-27 NPT Connections, Max. vacuum 23 hg, Min.
full load speed 2800 rpm, nominal free flow 1.15cfm, 12V 3.8 amps
Vacuum Gauge: Dual Scale, 0 to 30 Hg and 0 to 100kPa.

Temperature isplay: Type-K 3.5 Digit LED display (C is standard for export). C/F selectable via plastic jumper behind front
bezel, -105C to 1372C range. (-157F to 1999F).

Power: 115V/60Hz; 240V/50Hz (optional).

Probe Temperature Control: Compact, 1/32 DIN autotuning


indicating temperature controller with separate 25 amp solid
state relay. 115 VAC outlet 5-15R, Type-K jack for input.

imensions: HxWxD: 21 x 9.5 x 14


(53 cm x 24 cm x 35.5 cm)

Sample Inlet: 1/2 Stainless Steel Quick-Connect


(alternate sizes available)

Weight: 22 lbs (9.98kg)

See more information on our Method 4 Condenser


Assemblies and Accessories for use with the
XC-40 Source Sampler Console.
Method 4 Condenser Assemblies, Page 33

11

ISOKINETIC SOURCE SAMPLING EQUIPMENT


METHOD 5 PUMP ASSEMBLIES
Lubricated Rotary Vane Pump (0523)
The Lubricated Rotary Vane Pump
includes two 5 wire-reinforced, kink-free
hoses with nonreversible quick connects.
The pump is mounted in either the new,
improved, stronger tubular steel frame,
or the standard x-case with removable
covers providing easy access for service.
The wick style lubricator requires less
maintenance. Option V added for 240V.

XE-0523 Pump
Shown with Console

The open tubular steel frame is designed for


the meter console to sit on top of the pump
frame. For easy maneuverability, an optional
wheeled handle assembly is available. For
use with XF version sample pump assembly.

XF-05HW Optional Pump Frame

Handle Assembly. Black Tubular Steel with 8


Wheels

XF-05HW

Specifications

Motor: 1/4hp, 120/240V 60/50Hz 4.6/2.3


Amp., RPM 1725/1425
Measured Flow: 3.1 cfm@ 1 inch Hg;
1.5 cfm@ 15 inches Hg
Maximum Vacuum: 25.5 Hg
Weight: 35 lbs., (16kg)

XF-0523

XF-0523 Rotary Vane Pumps

XE-0523
XE-0523 Rotary Vane Pumps

12

Model

Description

XE-0523

Rotary Vane Pump in a Molded X-Case


(120V/ 60 Hz)

XE-0523-V

Rotary Vane Pump in a Molded X-Case


(240V/ 50Hz)

Model

Description

XF-0523

Rotary Vane Pump in Tubular Steel Frame


(120V / 60 Hz)

XF-0523-V

Rotary Vane Pump in Tubular Steel Frame


(240V / 50Hz)

E-0523 Open Aluminum Pump Frame


Model

Description

E-0523

External Pump Assembly (std), Vane


Pump, Open Aluminum Frame, Lubricator,
5ft Pwr Cord & Hoses,Stainless Quick
Connects Standard, 120V

E-0523-V

External Pump Assembly (std), Vane


Pump, Open Aluminum Frame, Lubricator,
5ft Pwr Cord & Hoses, Brass Quick
Connects Standard, 240V

ISOKINETIC SOURCE SAMPLING EQUIPMENT


METHOD 5 PUMP ASSEMBLIES
Double Headed Diaphragm
Pump (DAA)
The Double Headed Diaphragm Pump
will never require any lubrication. Pump
is easy to service within its frame and
includes a power cord, two 5 wirereinforced, kink-free hoses with nonreversible stainless steel quick connects
(this pump is not recommended for use in
extremely cold environments).

XF-DAA Pump Shown


with Console and
XF-05HW Optional
Pump Frame

XF-05HW Optional Pump Frame

Handle Assembly. Black Tubular Steel


with 8 Wheels.

XF-05HW
Specifications

Motor: 1/2hp, 120V/60Hz, 5 1/2 Amp


Measured Flow: 2.9 cfm@ 1 inch Hg;
1.4 cfm@ 15 inches Hg
Maximum Vacuum: 26.5 Hg
Weight: 30 lbs., (14kg)

*See Accessories for Spare parts

XE-DAA
XE-DAA Pumps Diaphragm Pumps
Model

Pump

XE-DAA

Double Headed Diaphragm Pump in a


Molded X-Case, 110V/60Hz

XE-DAA-V

Double Headed Diaphragm Pump in a


Molded X-Case, 220V/50Hz

XF-DAA

E-DAA Open Aluminum Pump Frame


Model

Pump

E-DAA

External Pump Assembly (alt), Double


Diaphragm Pump, Open Frame, 5ft Pwr
Cord & Hoses, 120V

E-DAA-V

External Pump Assembly (alt), Double


Diaphragm Pump, Open Frame, 5ft Pwr
Cord & Hoses, S.S. Quick Connects
Standard, 240Volt

XF-DAA Diaphragm Pumps


Model

Pump

XF-DAA

Double Headed Diaphragm Pump in


Tubular Steel Frame, 110V/60Hz

XF-DAA-V

Double Headed Diaphragm Pump in


Tubular Steel Frame, 220V/50Hz

13

ISOKINETIC SOURCE SAMPLING EQUIPMENT


NOZZLES FOR ISOKINETIC SAMPLING
NG-SET

NS-SET

Apex Instruments offers Button-Hook Nozzles in

multiple materials. The size needed for isokinetic


sampling depends on the stack gas velocity; the
material depends on the stack temperature and
the sampling method. The most popular nozzles are
constructed from seamless 316 stainless steel and
can be coated with FEP or SilcoSteelCR. Other
nozzle materials include Borosilicate Glass, Alloy
600 and Quartz. Standard sampling nozzles are 4
long and have a 5/8 o.d. shank for attaching to the
probe union. Stainless steel nozzles are configured with
an O-Ring to aid in positive leak checks. A bored out union
is needed with Apex O-Ring nozzles, although a standard
union can be used if the O-Ring is removed. Other sizes
and configurations are available. Nozzles must be measured
before initial use. Glass and Quartz Nozzles are available
with a female 14/35 ground glass taper joint eliminating the
need for the 5/8 union. For use with male taper joint probe liners.

Individual Nozzles
Unique to Apex Instruments,
the Nozzle Shank has integrated
Ferrule with O-Ring Groove.
O-Ring (O-O14V) shown.
Note: When using O-Ring, a Bored
Union, (P/N: N-10UB) is required.

Nozzle Sets
Nozzle Sets come in stainless
steel, glass, quartz, inconel or
FEP lined. Includes a Nozzle
Case, Seven Nozzles,
(sizes 4, 6, 8, 10, 12, 14, 16)
and select Accessories.

Size

Standard I.D.

Stainless
Steel
NS-

Inch

Decimal

mm

1/8

0.120

3.048

5/32

0.152

3.861

3/16

0.180

4.572

7/32

0.209

5.309

1/4

0.245

6.223

9/32

0.277

7.056

10

5/16

0.305

7.747

11

11/32

0.334

8.484

12

3/8

0.370

9.398

13

13/32

0.402

10.21

14

7/16

0.430

10.92

15

15/32

0.459

11.66

16

1/2

0.495

12.57

17

17/32

0.527

13.39

18

9/16

0.568

14.4

Alloy
600
NI-

Apex Instruments Threaded


Nozzle Set (NS-TH-SET) features
the larger ID nozzles for low stack
gas velocity and a buttonhook
Nozzle Blank (NS-THB) with a
tapered fitting. The set includes
seven SS Nozzle Tips that thread
onto the Nozzle Blank. Sizes
include 5/8, 11/16, 3/4, 13/16,
7/8, 15/16 and 1.

14

Glass
NG-

Quartz
NQ-

Glass
with
Taper
Joint
NG-T

Quartz
with
Taper
Joint
NQ-T

Silico
Coated
Stainless
Steel
NSIL-

Call For Additional Information

Nozzle Sets

Oversized Nozzles

FEP
Lined
Stainless
Steel
NST-

Nozzle w/ Female
14/35 Taper Joint

Model

Description

NS-SET

Stainless Steel Nozzles. Includes Four


5/8 Tube Nuts, O-Viton Rings

NG-SET

Glass Nozzles. Includes Three 5/8


Glass Filled PTFE Ferrules

NI-SET

Alloy 600 Nozzles, with Inconel Tube Nut

NQ-SET

Quartz Nozzles (Order Ferrules


Separately)

NST-SET

FEP lined, Stainless Steel Nozzles,


Includes Four 5/8 Tube Nuts, O-Viton
Rings

NSIL-SET

Silica Coated Stainless Steel Nozzle Set

Oversized Nozzles
Size
NS-TH

Nominal I.D.

Stainless
Steel

Inch

Decimal

mm

20

5/8

0.625

15.875

22

11/16

0.6875

17.462

24

3/4

0.750

19.05

26

13/16

0.8125

20.637

28

7/8

0.875

22.225

30

15/16

0.9375

23.812

32

1.0

25.4

Blank

ISOKINETIC SOURCE SAMPLING EQUIPMENT


Integrated Ferrule on Stainless
Nozzle for Steel Only

Nozzle Accesso ies


Nozzle Unions
Model

Description (Standard 5/8)

N-10

5/8 inch Stainless Steel Tube Nut.

N-10TG

5/8 inch Glass Filled Teflon Tube Nut, 12 flats (sided)


Fits Unions and Ball Adapters

N-10UB

Stainless Steel Union, Bored Out, with Nuts and Ferrules

N-10US

Stainless Steel Union, Bored Straight Through, with Nuts and


Ferrules

N-10UBT

Stainless Steel union, Bored Out, PTFE Coated, with


Nuts and Ferrules

N-10UST

Stainless Steel, Bored Straight Through, PTFE Coated, with


Nuts and Ferrules

NI-10UB

Alloy 600, 5/8 Tube Union Bored Out, with Nuts and Ferrules

NI-10US

Alloy 600, 5/8 Bored straight through, with Nuts and Ferrules

N-10USIB

5/8 Silcosteel-treated Stainless Steel Bored Union,


Nuts and Ferrules included

NTG-10U

Glass Filled 5/8 PTFE Tube Union with Nuts and Ferrules

NTG-10UNN

Glass Filled PTFE Tube Union without Nuts and Ferrules, Body Only

Individual Components can be Ordered Separately. Please Call for Pricing.

Tube Nuts
Model

Description (Standard 5/8)

N-10

5/8 Stainless Steel Tube Nut

NI-10N

5/8 Alloy 600 Tube Nut

N-10TG

5/8 Glass Filled PTFE Tube Nut

0-113V

Integrated
Ferrule
N-10

N-10UBNN

PS-[_]

N-10BR

PL-[_]

(Welded)

Nozzle nstallation for teel Alloys.


N-10UBNN
PL-[_] [_]

N-10

Nozzle
Quartz.
Nozzlenstallation
Installationfor
forGlass
Glass and
and Quartz.
mall Parts Kit

Includes 5/8 Bored Union Body, Nut, Ferrules,


Backer Ring and Viton O-Rings. PK-SP

Rings
Model

Description (Standard 5/8)

N-10BR

Thrust Backer Ring, 5/8 for O-Ring


Seal, Stainless Steel. For use with O-113V

Model

Description (Standard 5/8)

O-113V

Viton 5/8 O-Ring to seal liner (for use with N-10BR)

10FF-S

Stainless Steel, Front Ferrule

O-113V-DZ

Viton 5/8 O-Ring to seal liner (for use with N-10BR), Dozen

10FB-S

Stainless Steel, Back Ferrule

O-014V

Viton O-Ring for 1/2 UltraTorr Fitting when Adapting to 1/4


UltraTorr Fitting

10F-GR

Graphite High Temp, Single Ferrule

10F-GR-DZ

Graphite High, Temp, Ferrule (12 pc) Dozen

NTG-10F

Glass Filled PTFE, Single Ferrule

NTG-10F-DZ

Glass Filled PTFE, Ferrule (12 pc) Dozen

NI-10FF

Alloy 600 Front Ferrule


Alloy 600 Back Ferrule

O-014V-DZ

Viton O-Ring for 1/2 UltraTorr Fitting when Adapting to 1/4


UltraTorr Fitting, Dozen

Vinyl Nozzle aps

Great for Leak Checks!

Ferrules

Model

Description

NT-10BF

VPC-4-16

1/4 Vinyl Push-On Cap, 1/4 OD,


1 Inside Height, Red

NT-10F

PTFE Single Ferrule 5/8

NT-10F-DZ

PTFE, Single Ferrule, 5/8, (12 pc) Dozen

VPC-6-16

3/8 Vinyl Push-On Cap, 3/8 OD, 1 Inside Height, Red

VPC-8-16

1/2 Vinyl Push-On Cap, 1/2 OD, 1 Inside Height, Red

VPC-10-16

5/8 Vinyl Push-On Cap, 5/8 OD, 1 Inside Height, Red

Nozzle Brushes
Model

Description

NB-3

3/16 Diameter, Twisted Stainless Steel Wire and Nylon Bristles

NB-5

5/16 Diameter, Twisted Stainless Steel Wire and Nylon Bristles

NB-8

1/2 Diameter, Twisted Stainless Steel Wire and Nylon Bristles

NBT-1/2

PTFE Nozzle Brush, 1/2 Diameter, PTFE Barrel and Bristles

Nozzle Brush et (NB- T) One of each type brush from three


popular sizes in a convenient carrying tube (sizes 3, 5, & 8).

Recommended
Maximum Temperatures

NBT-1/2

NB-SET

Material
Max Temperature
Stainless Steel
650C (1200F)
PFA Fittings
177C (350F)
Borosilicate Glass
480C (900F)
Inconel
Quartz
Viton O-Rings
Graphite Ferrules
Glass Filled PTFE
Hastelloy C276

980C (1800F)
900C (1650F)
260C (500F)
980C (1800F)
315C (500F)
980C (1800F)

15

ISOKINETIC SOURCE SAMPLING EQUIPMENT


STAN AR MET O

EATE

PROBES

The Apex Instruments Standard Method 5 Heated Probe Sheath feature 1 diameter
sheaths constructed from corrosion resistant stainless steel, modular 3/8 pitot tip, 1/4
stainless steel quick connects, Type-K thermocouples for stack & probe temperature,
probe heater and an orsat line, small parts package. Standard lengths are 3 to
16. Longer lengths and custom orders are available by request. Order probe liners
separately. Probes are ordered according to nominal (liner length). Effective length is
one foot less than nominal length.

Standard Method 5 Probe


Optional Oversheath
Packing Gland
PG-32S

1 footshorter
shorter then
-1 -foot
theneffective
effective

Method 5 Probe with Optional Oversheath

Probe Sheaths & eaters


Replace
with Nominal
Length (feet)

Stainless Steel
Probe Sheath +
Heater PS-H

Packing Gland (Optional)


Optional with 2 OD
Probe Oversheath
PS-HO2

Replacement
Heater
PH-

Watt

350

350

400

400

7
8

Call For Additional Information

400
450
475

10

500

11

550

12

600

14

600

16

700

Add V to end of part number for 240V option at no extra cost.

Replacement Pitot Tips

-32

Method 5 Probe (Tube)

eaters

Features a tightly wound heating element around a rigid


tube. The rigid tube design allows liner replacement
without removing the heating element. Actual tube length
is 2-3/8 less than nominal length. Apex probe heaters
are designed to operate at the method 5 specified
temperature of 245F (+/-25 Degree F). Specify alternate
temp requirement if needed at the time of order. The
maximum recommended temperature is 260C (500F).
In extreme applications (probe heaters over 11 feet,
long u-cord, long power extension cord), power drops
may occur. In these instances, a separate temperature
controller is suggested. See Gas Analysis Section, Page
9 for Apex ICH-901 Temperature Controller. Alternate
wattage requirement to be specified at time of order.

Product

Description

MPT-6-133

Type S Modular Pitot Tip for Oversheath Probes, 3/8


Stainless Steel, 133mm

MPT-6-181

Replacement Pitot Tip for Standard Method 5 Probe Assemblies,


3/8 SS, 181mm

MPT-6-181OFF

Replacement Pitot Tip, 3/8, Stainless Steel, Offset for use with
47mm Filter holder and PM2.5 Cyclone, 181mm

MPT-6-218

Replacement Pitot Tip, 3/8, Stainless Steel, Extended for use


with Method 5 nozzle and SFA-47 In-Stack filter, Length 218mm

MPT-6-283

S type pitots manufactured in accordance with U.S. EPA


Reference Method 2 may be assigned a baseline coefficient
of 0.84. Geometric and wind-tunnel calibrations are offered:

Replacement Pitot Tip,3/8, Stainless Steel, extended for use


with PM10 Cyclone and 47mm In-Stack Filter, Length 283mm

MPT-6-320

Replacement Pitot Tip, 3/8, Stainless Steel, Extended for use


with standard Method 5 nozzle and SFA-190, SFA-300, or
SFA-2590 In-Stack Filters, Length 320mm

PT-CAL-G (Geometric Certification)

MPT-6-421

Replacement Pitot Tip, 3/8, Stainless Steel, Extended for use with
PM10/2.5 Cyclones and SFA-47 In-Stack Filter, Length 421mm

The unique design of the Apex Modular Pitot Tip reduces


the collection of water droplets in the pitot lines. The lower
tube is self-draining while the offset in the upper tube acts
as water trap.

length in mm

PT-CAL-W (Wind Tunnel Calibration)

16

PG-32S

2 Oversheath Packing Gland, 2 NPT Threads,


Stainless Steel with PTFE Ferrule. Must be
Specified at time of order.

ISOKINETIC SOURCE SAMPLING EQUIPMENT


P

Standard Probe Liners are constructed from 5/8 diameter tubing and have #28 ball joint
attached. Liners are available in borosilicate glass, quartz, stainless steel, Alloy 600 and
PFA; liners with integrated nozzles require a ball joint adapter. Glass and quartz liners
with male 14/35 taper joint are available for attaching to the nozzle, eliminating the need
for the 5/8 union.
Standard Probe Liner
Length in Feet

Tubing

Probe Liner with Nozzle


(shown with optional #28 ball adapter)
PLS-

GN

GA-28B10TG

Probe Liner with Male 14/35 Taper Joint and #28 Ball Joint

PLN- GT
or
PL- QT
N
Quartz or Glass

Specify Nozzle Size

PTFE

T
Size

Special Options

14/35 Taper

Probe Liners
Material
Replace
with Nominal
Length (feet)

Glass
PLN-G

Stainless
Steel
PL-S

Quartz
PL-Q

Alloy
600
PL-I

C-276
PL-C

GT
PLN-GT

3
4
5
6
7

Call For Additional Information

QT
PL-QT

I
S

d h

&

Isokinetic M5A-C Calculator

The Casio Graphic Scientific Calculator


comes pre-programmed with valuable
Isokinetic stack sampling calculations
making field calculations quick and easy.
Programmed in English and metric units.

Programs included:

M5A-C

Traverse Points Location


Stack Gas Velocity and Volumetric Flow Rate
Stack Gas Moisture Content
Stack Gas Saturation Moisture Content
Ideal Nozzle Size and K-Factor with H Loop
Post-Test Isokinetics
DGM Field Calibration using Critical Orifices

8
9
10
11
12
14

5 -C

16

Call for Pricing on PLS-

GN

Isokinetic Slide Rule

Adapters
Part Number

Description

GA-28B10TG

PTFE Adapter Glass filled, 28mm Ball to 5/8 inch Tube Fitting, Straight Probe
Liner Ball Adapter. Includes PTFE/glass nut, ferrule and Viton O-Ring

GA-28B10TGNN

PTFE Adapter Glass filled, 28mm Ball to 5/8 inch Tube Fitting, No Nut

Tubing

This device performs Isokinetic Stack Sampling


Calculations. The slide rule provides new H
settings at a glance.

M5A-1.......English Units
M5A-1M....Metric Units

Seamless, for use as probe liner (plain ends)


Part Number
TTG-10/6

Description
Glass Filled PTFE Probe Liner Material, 5/8 inch OD, 3/8 inch ID

TPFA-10/6

Tubing PFA, 3/8 ID x 5/8 OD Heavy Wall

TS10-035S

Seamless 316 Stainless Steel Tubing, 5/8 OD x .035 Wall

TI10-035S

Seamless Alloy 600 Tubing, 5/8 OD x .035 Wall

*See Accessories for Isokinetic Software

Monorails, page 52

17

ISOKINETIC SOURCE SAMPLING EQUIPMENT


SPECIAL ALLOY MET O

5 PROBE S EAT S

Alloy Method 5 Probe Sheaths are for hot corrosive gases. Includes a 3/8 pitot tip, 1/4 stainless steel quick connects,
stack temperature thermocouple with magnesium oxide insulation, and orsat line. The Alloy probe sheaths come standard
with Alloy 600 unions for nozzle and pitot (stainless steel optional). Order liners separately. Alternate alloys available, please
call for more information and for pricing.

- Recommended for High Temperature Applications


- Highly Corrosion Resistant

AIR COOLE

MET O

Call for current pricing for the following items:


Alloy Liners (PL-I)
Alloy Sheaths (IPS-)

5 PROBE

Air Cooled Method 5 Probes up to 8 in length, applicable for high temperature sources. Concentric tubular design allows the
cooling air to return and exhaust out of the stack. The probe sheath is constructed from stainless steel tubing while the liner,
pitot, thermocouple and nozzle union are made from inconel. A variable speed high capacity blower is needed for cooling.
Order blower separately.
SB2M

Add V to end of part number for 240 V at no extra cost.


SB3

d Probe

Air Coole

Air flow in air cooled probes.

SBR-93CFM

Air Cooled Method 5 Probe Assembly


with unheated alloy 600 Liner
Part
Number

Nominal
Length (feet)

APS-4I

APS-6I

APS-8I

Call for pricing on additional lengths.

18

Blowers

SBR Blower Assembly, variable speed 93 cfm, connects to SB-2M,


also includes hose (110V/60Hz). Add V for 240V option.

B -93CF
B -93CF -V
Glass and Quartz Liners Not Recommended Due to Breakage

ISOKINETIC SOURCE SAMPLING EQUIPMENT


MO ULAR SAMPLE CASE ASSEMBLIES

SB-2M Miniature
eated Filter Box

Apex Instruments Modular Sample Case Assemblies are


versatile, lightweight and available in a variety of configurations. There are three different filter ovens, and two different
risers that can attach to the bottom of the ovens, with four
different impinger cases. The impinger cases slide on and
off for easy changing of the impinger sets between test runs.
Several standard assemblies are available or the individual
components can be purchased separately. Please inquire for
additional details.

Heated Filter Box Standard Features


Lightweight aluminum construction
Stainless Steel Probe Clamp
Type K Thermocouple Jack
Probe and Auxiliary Power Jacks
500 Watt Heater (750 Watt Optional)
1/2 inch E-Glass Insulation
Mounting Hardware for Riser
Double Doors
Handle/Monorail Attachment
Aluminum Liner
Stainless Steel Latches
Internal Reinforcement

SBR-10

SB-3

SB-50 Modular Sample Case Assembly


Model

escription

SB-50

Modular Sample Case Assembly, Includes Miniature


Heated Filter Box SB-2M, Riser SBR-10, and Impinger
Box SB-3 (holds 4 impingers), 120 V

SB-50-V

Modular Sample Case Assembly, Includes Miniature


Heated Filter Box SB-2MV, Riser SBR-10, and Impinger
Box SB-3 (holds 4 impingers), 240 V

SB-50/4

Modular Sample Case Assembly, Includes Miniature


Heated Filter Box SB-2M, Riser SBR-10, and MId-Sized
Impinger Box SB-4 (holds 6-8 impingers), 1`0 V

SB-50/4-V

Modular Sample Case Assembly, Includes Miniature


Heated Filter Box SB-2M-V, Riser SBR-10, and Mid-Sized
Impinger Box SB-4 (holds 6-8 impingers), 240 V

SB-2 eated
Filter Box

Flexible Arrangement

SB-3

SB-1 Classic Modular Sample Case Assembly


Model

escription

SB-1

Modular Sample Case Includes SB-2 Heated Filter


Box & SB-3 Impinger Box, 120V

SB-1V

Modular Sample Case (Includes SB-2V Heated Filter


Box & SB-3 Impinger Box), 240V

SB-1/4
SB-1/4V

Rigid Arrangement

Modular Sample Case Includes SB-2 Heated Filter


Box, 110 VAC and SB-4 Impinger Box, holds 6-8
impingers
Modular Sample Case, includes SB-2 V Heated
Filter Box, 240V and SB-4 Impinger Box, holds 6-8
impingers

Monorails, page 52

19

ISOKINETIC SOURCE SAMPLING EQUIPMENT


F

Filter ovens have lightweight powder-coated aluminum-lined


panels with stainless steel clamps, hardware and E-Glass
insulation thermal insulation. Internal reinforcements reduce
flexing of box when testing with long probes. Front and rear
doors provide greater accessibility. The handle is designed for
attaching to a monorail for easy traversing. The 1 probe clamp
may easily be removed from the oven and replaced with different alternative probe clamps. A SBR-10 Riser is for mounting the
impinger case in the rigid arrangement. The SB-2 is the traditional
full-size filter oven that is designed for the rigid arrangements for
accommodating a cyclone before the filter. The SB-2M Miniature
Filter Box and SB-2 Filter Oven will accept standard 2, 3, and
4 filter assemblies.
SB-2M Miniature
eated Filter Box
has two access doors and
probe clamp; 120V/60 Hz
standard. Dimensions: 13.5
x 9.5 x 9.5, (34.3 x 24 x 24
cm), Weight: 10 lbs (4.5 kg).

B-2
SB-2M

Add V to end of part number


for 240V at no extra cost.

-2

GA-108

GA-104

20

Classic Full Size eated Filter Box


has 2 access doors, probe clamp
and accepts cyclone. 120 V/60 Hz
standard. Dimensions: 23.5 x 9.5 x
9.5, (60 x 24 x 24 cm),
Weight: 16 lbs (7.3 kg).
Add V to end of part number
for 240V/50Hz at no extra cost.

GA-113

The GA-107 strain relief is used with


sample lines at the SB-2M during Flexible
Method 5 sampling. Includes bracket that
attaches to the SB-2M and standard mount
with clamp. 1/2 tube.

-107-12

-V

-108

The GA-113 strain relief is used specifically with heated sample lines at the
SB-2M during Flexible Method 5 sampling.
Includes bracket that attaches to the SB2M and an adjustable Velcro strap to grip
heated sample lines.

-113

B-2 -

Stainless Steel #28 Socket Adapter


with Full Flow 3/8 quick connect and
Mounting Bracket, Used on SB-2M
Straight Thru To Attach Sample Line.

The GA-104 connects a 3/8 sample


line to the filter exit of the SB-2M oven.
Standard comes with #28 socket, thermocouple, and 1/2 to 3/8 reducing union.

-104

SB-2M-ST Straight Through Heated Filter Box has


two access doors and probe clamp. The Apex SB-2M-ST
is the SB-2M with the probe clamp raised so an in-line filter
assembly can be used without the need for the cyclone
bypass. In addition #28 Stainless Steel Socket with a 3/8
full flow quick-connect is installed on the outlet. Accepts
filter assembly GNFA-3-STR. Dimensions: 13.5 x 9.5 x
9.5, (34.3 x 24 x 24 cm), Weight: 10 lbs (4.5 kg) 120V/60
Hz standard. Add V to end of part number for 240V/50 Hz
at no extra cost.

B-2 -

B-2 -V
Shown with GA-104 Strain
Relief. Order Separately

SB-2M-ST
SB-2M-ST-V

B-2

Model

GA-107-12

SB-2

B-2V
escription

PC-1

Probe Clamp for 1 inch OD Probe Assemblies

PC-1VU

Vertical Probe Clamp for Up-Traverses, 1 inch


Clamp

PC-1VD

Probe Clamp for Down-Traverse, 1 inch Clamp

PC-2/32

Probe Clamps for 2 Bevel Packing Gland

ISOKINETIC SOURCE SAMPLING EQUIPMENT


I

Apex offers four different removable Sample Box Impinger Cases. These cases are constructed
from a thicker aluminum to reduce cracking, durable polyethylene foam insulation, and prepunched foam insert for holding the impinger bottles in place, and have a fold down handle with
a rope centering guide and two high strength brackets for mounting strain relief. The cases slide
on and off the heated filter box for easy changing of the impingers between test runs. All cases
are equipped with a spring-loaded latch to prevent accidental slippage.

Impingers Cases
Holds Impingers

SB-3

SB-4

SB-4S

SB-5

Model

Description

Dimensions (HxWxD)

Weight

SB-3

Impinger Box/Insulated Coolant Reservoir; Model 100

9.5 x 9.5 x 13.5 (24.1 cm x 24.1 cm x 34.3 cm)

5 lbs (2.3 kg)

SB-4

Impinger Box/Insulated Coolant Reservoir; Model 150

12.5 x 9.5 x 13.5 (31.8 cm x 24.1 cm x 34.3 cm)

6 lbs (2.7 kg)

SB-4SD

Impinger Box/Insulated Coolant Reservoir; Divided; Model 150

12.5 x 9.5 x 13.5 (31.8 cm x 24.1 cm x 34.3 cm)

6 lbs (2.7 kg)

SB-5

Impinger Box/Insulated Coolant Reservoir; Model 200

16 x 9.5 x 13.5 (40.6 cm x 24.1 cm x 34.3 cm)

7 lbs (3.2 kg)

Model

Description

SB-50

Modular Sample Case Model 50, (includes SB-2M, SBR-10, & SB-3 & probe clamp), 120V

SB-50-V

Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M-V, Riser SBR-10, PC-1, and Impinger Box SB-3, 220V

SB-50/4

Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-I, and MId-Sized Impinger Box SB-4
(holds 6-8 impingers), 110V

SB-50/4-V

Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-1, and MId-Sized Impinger Box SB-5, 220V

SB-50/5

Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-I, and MId-Sized Impinger Box SB-5, 110V

SB-50/5-V

Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-1, and MId-Sized Impinger Box SB-5, 220V

Sample Case Risers attach to the base of the filter oven for test methods requiring extra height between the filter
outlet and the first impinger. The SBR-10 Riser is required for attaching the impinger case to the SB-2M for rigid
arrangements. SBR-18 Riser is primarily used for Method 23 sampling when using a vertical condenser.
SBR-10
Model

Description

Dimensions (HxWxD)

Weight

SBR-10

Riser for SB-2M, impinger box adapter, 10 riser with insulated reservoir

9.5 x 9.5 x 10 (24.1 cm x 24.1 cm x 25.4 cm)

10 lbs (4.5 kg)

SBR-18

Riser for MM5, impinger box adapter, 18 riser with insulated reservoir

9.5 x 9.5 x 18 (24.1 cm x 24.1 cm x 45.7 cm)

10 lbs (4.5 kg)

GA-100
UA-3J

M d

SBR-18

The Modular Sample Frame (SB-8) with Probe Clamp is an ideal addition for sampling methods that
require no heated filter compartment such as Method 8, Method 306 and in-stack filtration methods.
The SB-8 secures the probe and impinger case in a rigid manner. The sample frame is made of
durable powder coated aluminum with stainless steel probe clamp and impinger case slides.

B-8
Umbilical (Gooseneck) Adapter
SB-8

SB-3

Impinger Inlet Strain Relief

The GA-109 strain relief is used with


sample lines at the impinger box when
performing Flexible Method 5 sampling. Includes bracket that attaches to
the impinger box and standard mount
with sample line clamp (specify size).
Available from 3/8 tube to 2 or 3.
-S is for Velcro version.

-109-12
-109-

GA-109-12

The GA-100 connects the final impinger outlet to the umbilical cable. Standard
with #28 socket, thermocouple and 1/2 stainless steel male quick connect.
Mounts on Impinger box.

GA-100

-100

Power Box Adapter

The UA-3J connects to umbilical 4-pin circular connector and


converts to three straight blade receptacles. Clamps to 1/2 sample
line or GA-100 adapter. The UA-3J is used in conjunction with the
Compact Method 5, Method 8, Method 17 and in other sampling
situations in which power for the probe is not available due to the
absence of a heated filter box.

UA-3J

-3J

UA-3J-V Adapter, Power,U-Cord, 3 receptacles, 220V Power


Box Adapter, Includes 1/2 inch Mounting Clamp and 4 Pin
Amphenol to 3 Receptacles.

-3J-V

UA-3J-V

21

ISOKINETIC SOURCE SAMPLING EQUIPMENT


ISOKINETIC GLASSWARE S
B

Apex Instruments offers a complete line of glassware. Our Standard Glassware


features extra heavy borosilicate glass with unground #28 Ball and Socket Joints with
O-Ring Seals. Cost effective unground joints are more durable than ground joints and
the O-Rings provide a tight, leak-free seal without grease. This set includes all the
glassware necessary for one train.

GN-11

GN-8-18K

O-116V #28 Ball Viton O-Ring

GNFA-3
GN-1

O-126V Impinger
Taper Viton,
O-Ring, Top
O-123V Impinger
Taper Viton,
O-Ring, Bottom

GN-2
Cyclone Body
(optional)

GN-3
Cyclone Flask
(optional)

GN-9A

GN-9AO

GN-9A

Basic Method 5 Glassware Sets

Method 4 Glassware Sets


Model

Description

Model

Description

GN-CG4

Basic Method 4 (Moisture) Glassware Set

GN-CGS

Basic Method 5 Glassware Set


(3 Filter Assembly)

GN-CGS4

Basic Method 5 Glassware Set


(4 Filter Assembly)

GN-CGS-Z

Basic Method 5 Glassware Set


(3 Filter Assembly) with OZ style Clamps

GN-CGS4-Z

Basic Method 5 Glassware Set


(4 Filter Assembly) with OZ Style Clamps

Includes:
Qty Part

Description

GN-8

Double L Adapter, Unground #28 Sockets

GN-9AO

Greenburg Smith Impinger with Orifice, Unground

GN-9A

Modified Greenburg Smith Impinger, Plain, Unground

GN-11

U-Tube, Unground Sockets

10

BS28WS

#28 Ball Joint Clamp, Generic

Alternative Styles and Filter Assemblies


Are also Available.

22

GN-9A

Includes:
Qty

Part #

Description

GN-1

Cyclone Bypass, Unground with O-Ring

GNFA-

Filter Assembly, Unground Glass, PTFE Frit,


Open Style Aluminum Clamp, 3 or 4

GN-8-18K

Double L Adapter with Type K Thermocouple


Assembly, Cap and Silicone Seal

GN-9AO

Greenburg Smith Impinger with Orifice, Unground

GN-9A

Modified Greenburg Smith Impinger, Plain, Unground

GN-11

U-Tube, Unground Sockets

12

BS28WS

#28 Ball Joint Clamp, Generic

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d5G

hT

M h d5G
S
The eluxe Method 5 Glassware Set with
Transport Case (GN- GS) contains all the
glassware plus spares for a full test series. Four
filter assemblies cover three sampling runs plus
one as a spare. Two full sets of impingers and
U-Tubes permit a second run before recovering
the first run results. The deluxe glassware set
includes spare impingers, U-tubes and Double
L adapters. The glassware set fits easily
into foam lined custom pockets. The sturdy
transport case is lockable for secure chain-ofcustody. Optional FEP Encapsulated O-Rings
are available upon request.

#28 Ball Joint Sockets are Standard.

NOTE: Set does not include cyclone or cyclone flask. Spare O-Rings are included.

eluxe Method 5 Glassware Set Includes:


Qty

Case imensions:
25 (63.5 cm) x 19 (48.2 cm) x 23 (58.4 cm)
Full Weight: 63 lbs. (29 kg.)
Empty Weight: 39 lbs. (18 kg.)
eluxe Method 5 Glassware Set

Part

Description

TC-GW2.5

Glassware Transport Case

GN-1

Cyclone Bypass, Unground with O-Ring

GNFA-

Filter Assembly, Unground Glass, PTFE Frit, Open


Style Aluminum Clamp. - Specify Size 3 or 4

GN-8

Double L Adapter, Unground Sockets

GN-8-18K

Double L Adapter with Type K Thermocouple Assembly, Cap and Silicone Seal

GN-9AO

Greenburg Smith Impinger with Orifice, Unground

GN-9A

Modified Greenburg Smith Impinger, Plain, Unground

GN-11

U-Tube, Unground Sockets

30

BS28WS

#28 Ball Joint Clamp, Generic

GA-3P

Filter Tripod

30*

O-116S

Silicone O-Ring for Grooved #28 Ball

Model

Description

10*

O-123V

Bottom Viton O-Ring for Impinger Insert

GN-DGS

Deluxe Method 5 Glass Set w/ Transport Case (3 FA)

10*

O-126V

Top Viton O-Ring for Impinger Insert

GN-DGS4

Deluxe Method 5 Glass Set w/ Transport Case (4 FA)

* Spares

GLASSWARE ACCESSORIES
Caps & Seals

#28 Ball Joint & Taper


Joints Seals

Ball Joint Clamps

Product

Description

GA-GL-18B

Bored Cap with hole, #18 threads

Product

Description

Product

Description

GA-18C

Solid Cap without hole, #18 threads

O-116V-DZ

BS28WS

GA-GL-18S

#18 Silicone Seal Ring, 50 Durometer


#18 Threads, 6.5mm Hole Diameter

Viton O-Ring for


grooved #28 ball, dozen

#28 Stainless steel


ball joint clamp

O-116T-DZ

RC-29

GA-GL-18ST

#18 Silicone with PTFE Seal Ring, #18 Threads,


6.5mm Hole Diameter, w/PTFE on half

TFE Encapsulated
Silicone O-Rings for
grooved #28 ball, dozen

#28 Stainless steel


ball joint clamp,
Pyrex brand

GA-GL-18T6

#18 Threads Silicone Seal Ring 6.5mm


Hole Diameter with PTFE on half

O-123V-DZ

Viton O-Ring for bottom


groove in Impenger Stem
Joint, Dozen

KBS-29

Keck Clip,
#29, plastic
ball joint clamp

GA-GL-18T8

#18/8 PTFE Seal Ring

O-126V-DZ

GA-GL-18/9

#18 Silicone Seal Ring, with PTFE


9 mm to 11 mm

Viton O-Ring for top


groove in Impenger Stem
Joint, Dozen

23

ISOKINETIC SOURCE SAMPLING EQUIPMENT


GLASSWARE FILTER ASSEMBLIES & COMPONENTS
2 Filter Components (55mm)
2 Unground Glass, PTFE Filter Support,
Open Style Aluminum Clamp.

F -2
2 U-Style Unground Glass, with 90 inlet
& outlet, PTFE Filter Support, Open Style
Aluminum Clamp.

F -2

Model

Description

GN-2S

2 Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend

GN-2B

2 Glass Filter Outlet, #28 Unground O-Ring Ball

GA-2CA

2 Aluminum Filter Clamp, Open Plate Style

GA-2T

2 PTFE Filter Support with Viton O-Rings

O-138T

FEP Encapsualted O-Ring for GA-2T

O-138V

Viton O-Ring for GA-2T

GA-2P

2 Nylon Filter Tripod

3 Unground Glass, PTFE Filter Support,


Open Style Aluminum Clamp.

3 Filter Components (82.6mm)

F -3

Model
3 Unground Glass Filter
Support, OZ Style Threaded Filter Clamp.

F -3Z
Open Style Aluminum Clamp, U-Style with
90o inlet and outlet, and #18 threaded joint.

F -3 -18
Kit with Thermocouple Assembly.

F -3 -18

Description

GN-3S

3 Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend

GN-3SS-S

3 Glass Short Stem, Straight Inlet with #28 Unground Socket

GN-3B

3 Glass Filter Outlet, #28 Unground O-Ring Ball

GA-3CA

3 Aluminum Filter Clamp, Open Plate Style

GA-3CZ

3 Single Thread Filter Clamp Assembly, OZ Style

GA-3T

3 PTFE Filter Support with Viton O-Rings

GA-3SS

3 Machined Stainless Steel Filter Support Disk with Viton


O-rings, Accepts 82.6 mm filter

O-152T

FEP Encapsulated O-Ring for GA-3T

O-152V

Viton O-Ring for GA-3T

GA-3G

3 Glass Filter Disk with Rubberized Edge

3 Unground Glass, PTFE Filter Support,


Open Style Aluminum Clamp, Straight
Through Style.

F -33 Glass Filter Disk


with Rubberized Edge.

-3
4 Unground Glass, PTFE Filter
Support, Open Style Aluminum Clamp.

F -4

4 Unground Glass, PTFE Filter support,


OZ Style Threaded Filter Clamp.

F -4Z
4 inch Filter Assembly, Unground Glass,
Poly Donut Spacer with TC assembly,
Dual PTFE Frits, Open Style
Aluminum Clamp.

3 Stainless Steel
Filter Support Disk.

-3

3 Filter PTFE Disk


with Viton O-rings.

-3t

4 Filter Components (110mm)


Model

Description

GN-4S

4 Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend

GN-4B

4 Glass Filter Outlet, #28 Unground O-Ring Ball

GA-4CA

4 Aluminum Filter Clamp, Open Plate Style

GA-4CZ

4 Single Thread Filter Assembly, OZ Style

GA-4T

4 FEP Filter Support with Viton O-Rings

O-156T

FEP Encapsulated O-Ring for GA-4T with Hollow Silicone Core

O-156V

Viton O-Ring for GA-4T

GA-4P

4 Nylon Filter Tripod

F -4-5
Filter Media, page 46-47

24

ISOKINETIC SOURCE SAMPLING EQUIPMENT


I d

dA

Apex Instruments offers a complete line of glassware featuring Extra Heavy Borosilicate Glass with unground #28 ball and
socket joints with O-Ring seals. Unground joints are more durable and price effective than ground joints and the O-Rings
provide a tight, leak-free seal without grease. Standard GN-Series Glassware includes Unground O-Ring joints and double
O-Ring 45/50 taper joints.

BOTTLES

INSERTS

387mm
15.0 in

380 mm.
13.0 in.

GN-9IK

GN-9IO

GN-9I
Model

Description

Model

Description

GN-9B

Bottle, unground taper joint, 500 ml,


330 mm x 57 mm

GN-9I

GN-9B-1

1.0 liter, 330 mm x 75 mm

Modified Greensburg-Smith O-Ring balls


(plain stem), unground taper joint with double
O-Ring seals

GN-9B-1.5

1.5 liter, 330 mm x 100 mm.

GN-91O

Greenburg-Smith (orifice stem), O-Ring ball,


unground taper joint with double O-Ring seals

GN-9B-2

2 liter, 330 mm x 110 mm

GN-91K

GN-9B-4

4 liter, 330 mm x 140 mm

Knock-out stem, O-Ring balls, unground taper


joint with double O-Ring seals

GN-9B-M7

Method 7 Bottle, 250 ml, accepts GN-9I.


330 mm x 38 mm

( OTTLES WIT

INSERTS)

403mm
15.867in

GN-9A

GN-9AO

GN-9AK

GN-3

Description

GN-9A

Modified Greenburg-Smith
(plain stem), 500 ml

GN-9AO

Greenburg-Smith (stem with orifice


and plate), 500 ml

GN-9AK

Knock-out (short stem), 500 ml

GN-9AO-M7

Method 7 (stem with restricted


orifice), 250 ml

Model

Description

GN-2

Cyclone Body, #28, unground


socket and O-Ring ball

GN-3

Cyclone Flask, #28


unground sockets

GN-2RH

Cyclone for Mini Hot Box, Reduced


Height, includesTeflon-lined #30 Cap

GN-9AO-M7

CYCLONES

GN-2

Model

GN-2R
25

ISOKINETIC SOURCE SAMPLING EQUIPMENT


I d

dA

GN-1

GN-11

Model

Description

GN-1

Cyclone Bypass, #28 unground socket and O-Ring Ball

GN-1-18

#18 Thread for TC (no cap or TC) (not shown)

GN-8

Double L with #18 Thread for TC. Order


cap and seal separately

GN-8-18

Double L with #18 Thread for TC. Order


cap and seal separately

GN-13

GN-8

GN-8-18K Double L withType-K TC assembly,


cap and silicone seal
GN-11

U-Tube, #28 unground sockets

GN-13

Filter By-Pass, #28 unground socket and O-Ring ball

GN-8-18K

Controlled Condensate Glassware


GFA-2590N-CCS
Use with these Connections

GFA-2590N-CC
GFA-2590B-CC

26

Product

Description

GFA-2590N-CCS

GFA-2590 Insert Straight-Thru with


Unground #28Socket to Male Taper Joint,
Connects directly to probe. Linear distance
socket to taper start 2.5 inches.

GFA-2590B-CC

Body for Controlled Condensate Method with


ground #28 Ball on outlet

GFA-2590N-CC

Insert with S Offset, Unground #28 Socket

GFA-2590B-CC

Body for Controlled Condensate Method with


ground #28 Ball on outlet

GN-HCCH-A

Horizontal Condenser, CCS, Assembly #28


Controlled Condensate Sampling with #11 port
for inserting cartridge heater, with Heater and TC
assembly, #28 Socket both ends, Water Jacket
w/Hose Barbs, TC-well and # 15 Solid Cap

Glass Cap #28


unground socket.

-16
Glass Plug, #28
unground ball with
Vitron O-Ring.

-17

ISOKINETIC SOURCE SAMPLING EQUIPMENT


I d
C

dA

Product

Description

VGC-9A

Condenser Assembly-Includes #7 and #11


nylon caps with o-rings and PTFE ferrules.

VGC-12A

Condenser Assembly-Includes black nylon


bushings, caps o-rings and PTFE ferrules.

VGC-9A

VGC-12A

Ad

GN-18

GN-18B

GN-19

GN-20B

GN-20S

Model

Description

Model

Description

GN-20B4

#28 unground O-Ring ball to 1/4 tube

GN-18

#28 unground socket to hose barb

GN-20B6

#28 unground O-Ring ball to 3/8 tube

GN-18B

#28 unground O-Ring ball to hose barb

GN-20B8

#28 unground O-Ring ball to 1/2 tube

GN-20S4

#28 unground socket to 1/4 tube.

GN-20B10

#28 unground O-Ring ball to 5/8 tube

GN-20S6

#28 unground socket to 3/8 tube

GN-19

#28 unground O-Ring ball to #22 thread.


Order cap and seal separately

GN-20S8

#28 unground socket to 1/2 tube

GN-20S10

#28 unground socket to 5/8 tube

Method 17 Glassware

GFA-2590N

GF-2590

G-47N

GFA-2590B

Product

Description

Product

Description

Product

Description

GFA-2590N*

Nozzle Insert, Glass for


GFA-2590 In-Stack
Filter Assembly, Specify
Nozzle Size (N4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 16, 18, 20)

G-47N 4

Nozzle I.D. 1/8

G-47N 10

Nozzle I.D. 5/16

G-47N 5

Nozzle I.D. 5/32

G-47N 12

Nozzle I.D. 3/8

G-47N 6

Nozzle I.D. 3/16

G-47N 14

Nozzle I.D. 7/16

G-47N 7

Nozzle I.D. 7/32

G-47N 16

Nozzle I.D. 1/2

G-47N 8

Nozzle I.D. 1/4

Glass Filter Inlet, 47 mm, with Attached Nozzle

GFA-2590

Thimble Filter, 25x90mm,


Binderless Glass Fiber,
Tapered, 10/box

GFA-2590B

Filter Body, Glass, for GFA-2590


Filter Assembly, 5/8 shank

27

ISOKINETIC SOURCE SAMPLING EQUIPMENT


I d

dA

Method 202 Glassware


Product

Description

GN-VCHM-M202

M202 Spiral Condenser, #28 Socket


both ends Water Jacket Hose Barbs,
High Moisture sources above 15%

GN-9AKS

Knock-out Impinger Assembly,


Unground, (for HorizMM5)

GNFA-3U-18K

3 inch Filter Assembly, Unground


Glass with 90 degree Inlet & Outlet,
Open Style Alum Clamp & TC

GNFA-3U-18K

GN-VC M-M202

Product

Description

GN-9AKSA

Knockout Impinger Assembly - 24/40 Taper Unground (for HorizMM5),


Included with Long / Short Stem.

GN-9AKSB

Knockout Impinger Bottle - 24/40 Taper Unground (for HorizMM5),


Used with Long / Short Stem.

GN-9AKSI

Knockout Impinger Stem - 24/40 Taper Short Male, Used


Before Purge on MTHD 202.

GN-9AKSIL

Knockout Impinger Stem - 24/40 Taper Long Male


Used for Purge on MTHD 202.

GN-9AKS
GN-9AKSA

GN-9AKSI

Method 23 Glassware

GN-9AKSB

GN-9AKSIL

GNM- C-18F
GNM- C

GNM-T

GNM- C-18

28

Product

Description

GNM-HC

Horizontal Condenser, #28 Unground Sockets, Water Jacket Hose Barbs.

GNM-HC-18

Horizontal Condenser, #28 Socket both ends, Water Jacket with Hose
Barbs with #18 GL joint for monitoring condenser outlet temperature.

GNM-HC-18F

Horizontal Condenser, #28 Socket both ends, #18 joint for monitoring
Filter Outlet temperature, Water Jacket with Hose Barbs,
Glass Type K thermocouple assembly NOT included.

GNM-T

XAD Trap, #28 Unground Socket & O-Ring Ball (Top), Water,
Jacket Hose Barbs.

GN-9AKS

Knock-Out Impinger Assembly, Unground (for Horizontal MM5)

GN-9AKSA

Knockout Impinger Stem - 24/40 Taper Short Male, Used


Before Purge on MTHD 202.

GN-9AKSA

GN-9AKS

ISOKINETIC SOURCE SAMPLING EQUIPMENT


B

dS

Ad

Glass-Filled PTFE

Apex offers Glass-Filled PTFE #28 Ball and Socket


Adapters. Glass fiber fillers are added to Virgin PTFE
to improve upon the mechanical properties. Adapters
are resistant to deformation under a heavy load and will
significantly improve the performance of the seal during a
test. Glass-filled adapters are tapped for 1/4 NPT fittings.

Glass Filled PTFE

#28 Socket to 3/8 Tube Fitting


(Includes Nylon Nut & PTFE Ferrule)

PFA Fittings

Apex offers both Straight and Elbow PFA Fittings with


1/4 NPT for 1/4, 3/8 and 1/2 tubing and a ball joint
with a 5/8 tube union for adapting to plain probe liners.
PFA (Perfluoro-alkoxy) fittings are chemically inert and
highly corrosive resistant. Higher mechanical strength
than PTFE at elevated temperatures (to 500O).

-28 6

PFA Straight Connectors:

Glass Filled PTFE

1/4 Tube Fitting


to 1/4 MNPT

3/8 Tube Fitting


to 1/4 MNPT

#28 Ball to 1/4 Female NPT

C4 - F

C4 - F

1/2 Tube Fitting to 1/4 MNPT

-28B4

C4 - F

PFA Elbow Connectors:

Glass Filled PTFE

#28 Socket to 1/4 Female NPT

-28 4

1/4 Tube Fitting


to 1/4 MNPT

3/8 Tube Fitting


to 1/4 MNPT

4 - F

4 - F

1/2 Tube Fitting to 1/4 MNPT


8

4 - F

Glass Filled PTFE

#28 Ball to 5/8 Tube Fitting


(Includes glass Nut, Ferrule
and Viton O-Ring)

-28B10

Probe Liners, page 17

Glass Filled PTFE Union

5/8 Union (includes nuts and ferrules)

-10

Glass Filled PTFE Nut

Glass Filled PTFE 5/8 Tube Nut

-10

Glass Filled PTFE Ferrules


5/8 Glass Filled PTFE Ferrule

-10F

Glass Filled PTFE Union


Tube Union, 5/8 Body Only

-10

5/8 Glass Filled PTFE Ferrule, Dozen

-10F- Z

29

ISOKINETIC SOURCE SAMPLING EQUIPMENT


B

dS

Ad

Apex Instruments offers Stainless Steel #28 Ball and Socket Adapters in a variety of sizes,
used for connecting to rigid or flexible sample lines. The #28 Ball includes O-Ring (O-116V).
Stainless Steel Straight Adapter

Stainless Steel Ball Adapters


#28 Ball to 1/4 FNPT

1/4 Tube Fitting to 1/4 MNPT

-28B4

C4 -

3/8 Tube Fitting to 1/4 MNPT

Stainless Steel Socket Adapter

#28 Socket to 1/4 Tube Fitting

-28 4

C4 -

1/2 Tube Fitting to 1/4 MNPT

#28 Socket to 1/4 FNPT

Fitting Size
Tube Union

C4 -

-28 4

4N=NPT
(Female)

#28 Socket to 3/8 Tube Fitting

Stainless Steel Male Elbow Connector

-28 6

1/4 Tube Fitting to 1/4 MNPT

#28 Socket to 1/2 Tube Fitting

-28 8

#28 Socket to 5/8 Tube Fitting

-28 10

4 -

1/2 Tube Fitting to 1/4 MNPT

Stainless Steel Socket


& Elbow Adapter

4 -

Double L Adapter w/Thermocouple Kit


-8-4

#28 Socket 3/8 Elbow Tube Fitting

-28 4

4 -

3/8 Tube Fitting to 1/4 MNPT

Stainless Steel U-Tube Connector

Stainless Steel Double L Connector

U-Tube connector with #28 Sockets.

-11

Double L with #28 Sockets and 1/4


Union for Thermocouple. (TCA-6X24).

-8-4

dA

Stainless Steel Impingers and Accessories are manufactured with #28 Ball and Sockets, 2 diameter and a 500ml capacity.
Stainless Steel Impingers are interchangeable with glass impingers for many applications. This kit includes an impinger with
Double L Inlet Stem, one impinger with restricted inlet U-Stem, two impingers with plain inlet U-Stem, straight inlet stem,
five #28 ball joint clamps.

Stainless Steel Impingers and Accessories

30

Model

Description

S-9A6

Impinger Bottle, 500 ml, 2 diameter, 3/8 Tube Unions, Q-Clamp, No Stem,
Stainless Steel

S-9AL

Impinger Double L, Inlet Stem and #28 Socket and Ball with,
Stainless Steel

S-9AO

Impinger with Restricted Inlet U-Stem, #28 Socket and Ball, Stainless Steel

S-9A

Impinger with Plain Inlet U-Stem, #28 Socket and Ball, Stainless Steel

S-9IL

Double L Inlet Stem, #28 Socket with Plain End, Stainless Steel

S-9IS

Straight Inlet Stem, #28 Ball with Plain End, Stainless Steel

S-9IR

U-Stem Inlet, #28 socket on 3/8 Tube with Restricted Tip, Stainless Steel

S-9I

U-Stem Inlet, #28 socket on 3/8 Tube with Plain Tip, Stainless Steel

S-9IT

Stem Outlet, #28 Ball with O-Ring on 3/8 Tube, Stainless Steel

S-9C2

2 Q-Clamp with Wing Nut, Stainless Steel

40MPU-2

For 2 Q-Clamp, Gasket Buna

S-9B

Impinger Bottle Only, 500 ml, Stainless Steel

S-9I

S-9IL

S-9IT
BS28WS

S-9B

S-9IS

S-9AL

S-9AO
T

S-9A

S-9A
.

See Page 23 for Ball Joint Clamps

Set of 4 Stainless Steel Impingers - Stainless Steel


Impinger Condenser Assembly, #28 Socket & Ball,
Methods 4, 5 and 17. S-5CN

ISOKINETIC SOURCE SAMPLING EQUIPMENT


S lit B ck Um ilic l A le

Split Umbilical Cables replace Standard Umbilical Cords for added versatility. They are constructed the same way as the
Standard Method 5 umbilicals with the sample line and exit thermocouple split to the specified length. Split umbilicals are
useful in flexible systems when the filter compartment is separated from impinger box with a flexible sample line such as
Method 17, Flexible Method 5 set-ups and Compact Method 5. The umbilical lengths are specified according to overall
length. Stainless steel quick connects are standard.
Exit

Split Umbilical

ables

Orsat
Pitot 1/4 QC

Model

Description

US-30-10

30 Umbilical w 10 Split 1/4 Pitot Quick Connects,


Stainless Steel Quick Connects

US-60-10

60 Umbilical w 10 Split 1/4 Pitot Quick Connects,


Stainless Steel Quick Connects

US-90-10

90 Umbilical w 10 Split 1/4 Pitot Quick Connects,


Stainless Steel Quick Connects

Aux
Stack
Probe

Sample 1/2 QC

Filter

Filter
Amphenol
Oven

Split -Back Umbilical Cord

Alternate Lengths Available, Call for Pricing

Umbilical

ord Bag

6 connectors

Large Canvas Bag with straps and logo

To Meter Console

Split Umbilical

U-BAG

ic Um ilic l

ord

le

Are lightweight with braided cover. The easily repaired umbilical cable includes one kink-free, wire reinforced sample line, 3
kink-resistant polyethylene lines (2 pitot & 1 orsat line), 6 type K thermocouple extensions, and five conductor electrical cable
with 4-pin circular connectors. Thermocouple plugs are colored coded. The sample line has 1/2 inch quick connect and the pitot
lines have 1/4 inch quick connects standard (3/8 inch optional). Standard lengths are 30, 60 and 90 feet. U-bag included.

cl

ic Um ilic l

Power Box Adapter


(UA-3J)

The UA-3J connects to umbiliUA-3J


UA-3JV
cal 4-pin circular connector and
converts to three straight blade
receptacles. Clamps to 1/2 inch sample line or GA-100
adapter. The UA-3J is used in conjunction with the
Compact Method 5, Method 8, Method17 and in other
sampling situations in which power for the probe is not
available due to the absence of a heated filter box.

UA-3J
UA-3J-V

Probe Power Adapter (UA-HJ)

lassic Umbilical ord


Model

Description

U-30

30, Method 5, 1/4 Pitot Quick Connects, Stainless Steel Quick Connects

U-60

60, Method 5, 1/4 Pitot Quick Connects, Stainless Steel Connects

U-90

90, Method 5, 1/4 Pitot Quick Connects, Stainless Steel Quick Connects

Optional Accessories
Model

Description

U-BAG

Large Canvas Bag with straps and logo

QS4/6

Stainless Steel Quick Connects 1/4 Male, 3/8 Female Pitot Quick Connects

QS6

Stainless Steel Quick Connects 3/8 Male and Female Pitot Quick Connects

Connects to umbilical 4-pin circular connector


and converts to a single female receptacle
UA-HJ
for the probe power.

UA-HJ

Heated Filter Box Power


Adapter (UA-FP)

UA-FP

The UA-FP connects with male plug to the


4-pin circular connector on the filter oven and
allows the oven to connect to a standard receptacle.

UA-FP

Heated Filter Box Power


Adapter (UA-FP2)

Heated Filter Box Power Adapter,


Includes one (1) 4 Socket Amphenol to
two (2) Male Standard 120V Plugs

UA-FP2

31

ISOKINETIC SOURCE SAMPLING EQUIPMENT


N

dS

Unheated Sample Line jumpers are used between the filter and the first impinger
in flexible sampling arrangements. Jumpers are available in various lengths and
configurations. Stainless steel overbraid 3/8 ID PFA tubing is standard.

USL--SST

Connects to the
SB-2M

Unheated Sample Line


Model

Description

USL--

USL- Length in feet / SST (#28 socket elbow fitting) or QST


(1/2 quick connects/#28 socket elbow)

USL-10-SST

10 Unheated, PTFE/Stainless Steel Overbraid, w/Thermocouple Assembly,


#28 Stainless Steel, Socket Elbow Fittings

USL-10-SS

10 Unheated Sample Line, 3/8PTFE/Stainless Steel


PTFE with SS overbraid, #28 Socket Elbow Fitting Both Ends

USL-15-SST

15 Unheated, PTFE/Stainless Steel Overbraid, w/Thermocouple Assembly,


#28 Stainless Steel, Socket Elbow Fittings

USL-25-SST

25 Unheated, PTFE/Stainless Steel Overbraid, w/Thermocouple Assembly,


#28 Stainless Steel, Socket Elbow Fitting

USL-10-QST

10 Unheated, PTFE/Stainless Steel Overbraid, 1/2 Female Stainless


Steel Quick Connect, w/Thermocouple Assembly, #28 Stainless Steel Socket Elbow

USL-15-QST

15 Unheated, PTFE/Stainless Steel Overbraid, 1/2 Female Stainless Steel


Quick Connect, w/Thermocouple Assembly, #28 Stainless Steel Socket Elbow

USL-25-QST

25 Unheated, PTFE/Stainless Steel Overbraid, 1/2 Female Stainless Steel


Quick Connect, w/Thermocouple Assembly, #28 Stainless Steel Socket Elbow

dS

USL--SS
Connects to
Probe Liner
Impinger

USL--QST
Connects to
the SFA-82

Heated Sample Line Jumpers are used when source sampling site has limited access and insufficient space for a traditional,
rigid sample train. Apex Instruments manufactures short heated sample lines/jumpers for use between the probe and the
heated filter assembly or between the probe and the first impinger inlet. Temperature Controller Required.

eated Sample Line Jumper


HSL--

HSRL- Diameter of each sample or cal gas tubing (4 = 1/4, 6 = 3/8, 8= 1/2)
- Length of line in feet

HSL-6-10

10, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.

HSL-6-15

15, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.

HSL-6-20

20, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.

HSL-6-25

25, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.

HSL-6-10V

10, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.

HSL-6-15V

10, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.

HSL-6-20V

20, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.

HSL-6-25V

25, 3/8 PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.

Add V to end of part number for 240V at no extra cost.

eated Sample Lines/Jumpers

GA-107-

GA-113

Mini eated Filter Box Sample Line Strain Relief


The GA-107 strain relief is used with sample lines at the SB-2M during Flexible Method 5
sampling. Includes bracket that attaches to the SB-2M and standard mount with sample line
clamp (specify size).

32

Model

Description

GA-107-9

Line Adapter (for SB-2M), includes Bracket and 3/8 inch ID Sample Line Clamp

GA-107-12

Line Adapter (for SB-2M), includes Bracket and 1/2 inch ID Sample Line Clamp

GA-107-32

Line Adapter (for SB-2M), includes Bracket and 1-1/4 inch ID Sample Line Clamp

GA-107-50

Line Adapter (for SB-2M), includes Bracket and 2 inch ID Sample Line Clamp

GA-107-57

Line Adapter (for SB-2M), includes Bracket and 2-1/4 inch ID Sample Line Clamp

The GA-113 strain relief is used


specifically with heated sample
lines at the SB-2M during
Flexible Method 5 sampling.
Includes bracket that attaches
to the SB-2M and an adjustable
Velcro strap to grip heated
sample lines.

GA-113

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d4S

Method 4 Determination of the Moisture Content of Stack Gas Summary:


Stack gas is extracted at constant rate (less than 21lpm) and a minimum
volume of 600 liters. Moisture is removed from the sample stream, and
measured volumetrically or gravimetrically.

- 4
- 4-V
Method 4 Individual Accessories
Part

Description

PC10-4S

CEM IRM Probe, 4ft,


Stainless Steel Sheath,
5/8 Stainless Steel Liner.

PLS-4S-QCF6 Probe Liner, 4ft, SS, w/Full


Flow, 3/8 QC.
USL-15-QS

15ft Unheated Sample Line,


PTFE with SS Overbraid,
#28 Socket Elbow Fitting
and Full Flow 3/8 QCF
Elbow Fitting.

SB-8

Probe Clamp Frame

GN-CG4

Method 4 Glassware Set,


Unground Joints.

SB-3

Impenger box, Model 100,


Insulated Cooltant Reservoir,
Holds 4 Impingers

GA-100

Sample Case Adapter

US4-25-10

U-Cord, Method 4, 25,


Splitback 10ft.

Flexible Method 4 Arrangement

Meter Console Sold Separately

XC-40 Meter Console


Recommended for Method 4 Testing
Rigid Method 4 Arrangement
Meter Consoles, page 4-11

33

ISOKINETIC SOURCE SAMPLING EQUIPMENT


ASIC-PLUS M

h d5

For a source sampling company to get started sampling for particulates (U.S. EPA
Reference Method 5), Apex recommends a combination of equipment that can be
configured for both rigid and flexible set-ups.
Select your METER CONSOLE (see page 8-10)
Select your SAMPLE PUMP (see page 12 - 13)

- 5B
- 5B -V
Basic Method 5 Includes:

Stainless Steel Nozzle Set


6-ft Probe with Heater
1 Stainless Steel Probe Liner, 3 Glass
Probe Liners
30-ft Split U-Cord
15-ft Unheated Sample Line
Hot & Cold Box Assembly with Riser
Sample Frame for Cold Box
(Flexible Config.)
Strain Reliefs
Basic Glassware Set
(1 sample run configuration)
Filter Paper
Brushes (Probe & Nozzle)
Calculator (programmed for Method 5)

Schematic of Method 5 Flexible Sampling Train

h d5

The professional source sampling company must be prepared for a wide variety of conditions and locations. Apex recommends the Deluxe Plus system, which can be used
in both rigid and flexible configurations. Even with the classic rigid arrangement, the additional glassware allows you to have pre-measured and filled impingers, pre-weighed
filter assemblies, and minimum turnaround time between runs. The flexible arrangement is effective for challenging environments like vertical traverses and space-limited
sources. After selection of a meter console and external sample pump, the Deluxe-Plus
system provides all of the components listed in the above Basic-Plus system.
PLUS:
Glass Nozzle Set
3-ft & 9-ft Probe Assemblies with
Stainless Steel & Glass Probe Liners
60-ft Split U-Cord
2.5 Sets of Glassware Plus
Carrying Case
4 Monorail Assemblies (9-ft & 12-ft)
Transport Case for a
Meter Console
Calibrated Orifice Set

- 5
- 5

34

-V

Schematic of Method 5 Rigid Sampling Train

ISOKINETIC SOURCE SAMPLING EQUIPMENT


OMPACT M

h d5

The Apex Compact Method 5 Sampler Kit features an independently Heated


Stainless Steel Filter Assembly (SFA-82H) that connects directly to a standard
Method 5 probe. It does not require a separate heated filter compartment, and
utilizes a flexible sample line, and a split umbilical cord with power adapter, to
allow sampling in space-limited areas. The standard glass impingers have been
replaced with Stainless Steel Impingers (S-5CN) to eliminate glass breakage.
Three filter assemblies are recommended to speed up the turn around time
between consecutive runs. Add V to end of part number for 240V
option at no additional cost.

-C 5
-C 5-V

SK-CM5 Kit
Heated Filter Assemblies (3)
Probe Sheath with Heater
Stainless Steel Probe Liner
Impinger Box
Impinger Inlet Strain Relief
60 Split Umbilical Cord
Unheated Sample Line with
Stainless Steel Overbraid
Power Box Adapter
Umbillical Adapter
Stainless Steel Nozzle Set
Stainless Steel Impinger Assembly
PTFE Coated Glass Fiber Filters

Schematic of U.S. EPA Method 5 Compact Sampling Train

dF

The Apex Instruments Heated Stainless Filter Assembly (SFA-82H) is for sampling particulates from space-limited industrial
sources. The filter assembly has a two piece threaded clamping ring with an integral 300 watt ring heater . A Viton O-Ring
seals the 82.6 mm filter and prevents sample bypass. It has stainless steel inlet, outlet and a PTFE filter support screen (GA3T). The inlet plate comes with a 5/8 tube union for swaging directly to a plain probe liner. The outlet plate has 3/8 female
NPT connection and a male 3/8 full flow quick connect. The mating female quick connects with the thermocouple, which
is supplied with the Unheated Sample Line (USL--QST) or SFA-82-QCF6, may be ordered separately. There is a thermal
insulated blanket supplied with each unit. An unheated version is also available without the integral heater and blanket.
Add V to end of part number for 240V at no extra cost.

SFA-82 (unheated)
F -82
F -82 V
F -82- CF6
F -82-B
Depending upon the source, it may be possible to combine
Method 5 and Method 8 into the same train.

SFA-82-BKT
SFA-82
SFA-82-QCF6

35

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d 5G

Method 5G Determination of Particulate Matter Emissions from Wood Heaters (Dilution Tunnel
Sampling Location). The exhaust from a wood heater is collected with a total collection hood,
and is combined with ambient dilution air. Particulate matter is withdrawn proportionally from a
single point in a sampling tunnel and is collected on two glass fiber filters in series.

F -4-5
Components Include:
4 Filter Assembly, Unground Glass #28 Ball/Socket, Poly Donut Spacer with Thermocouple
Assembly, Dual PTFE Filter Supports and Open Style Aluminum Clamp.
GNFA-4-5G

h d 5I

The M
5I S
K is similar to Basic Method 5, except for the addition of the 5I Holder (SGFA-47-5I) and is
designed for the determination of low-level particulate matter (PM) emissions from stationary sources. Method 5I is most
effective for PM catches less than 50 mg and is valid for performing correlation of manual PM measurements to PM continuous emission monitors or determining PM emissions from low-level sources such as turbines. Add V to end of part
number for 240V at no extra cost. After selecting a Method 5 Meter Console and an external sample pump in conjunction
with a Method 5 kit, add a Method 5I Holder.
The 5I Filter Holder inlet is constructed of Borosilicate Glass to hold a 47mm glass fiber filter with a wafer-thin stainless
steel filter support and a Viton O-Ring. The assembly is wrapped with PTFE tape for weighing, averaging less than 35
grams, providing a positive seal against leakage. Method 5I 47mm Filter Assembly with Glass Inlet & SS Outlet, with 2 45
deg bends.

SGFA-47-5I

h d 5I F

(Straight) Same Application as Method 5I

Straight version of SGFA-47-5I, for use with SB-2M-ST, straight through heated filter box.

F -47-5

SGFA-47-5IS

36

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d8

The Method 8 Sampling Kit is used with either the XC-522


or XC-572 Meter Console and an external sample pump
for the determination of sulfuric acid mist and sulfur dioxide
emissions from stationary sources. U.S. EPA Reference
Method 8 was originally developed to test emissions from
sulfuric acid plants but has been adapted to sample emissions from sulfur dioxide sources. Call for details on Flexible Arrangements. Add V to end of part number for 240V
at no extra cost.
M
A

h d8R

d d

Part

Description

SB-8

Sample Frame with


Probe Clamp

UA-3J

Power Box Adapter

GNFA-2U

2 Filter Assembly,
Unground Glass with
90 Inlet and Outlet,
Open Style Alum Clamp

Method 8 Sampling Kit

PS- H PLN- G
Glass Lined Probe

UA-3J
GA-100

Glass Nozzle
NG-

SB-8

SB-3

US- -10

Schematic of EPA Method 8 Sampling Train

dC

Conditional Test Method CTM-13


Controlled Condensate is an alternative to EPA Method 8 for determining
sulfuric acid emissions. Sulfuric acid vapor or mist and the sulfur dioxide
are separated, by controlling the condensation based on difference in dew
points, and both fractions are measured separately by the barium-thorin
titration method. Controlled condensation method is the primary sampling
and analytical tool for quantifying sulfuric acid emissions from stationary
sources. The method is based upon the selective condensation
GFA-2590#-CC
of sulfuric acid from a gas stream by means of a water cooled
condenser. The major advantage of the condensation method
is that it provides reliable reproducible SO3
and SO2 values with minimal interference
from high SO2 concentrations.
There are several versions of
the method. Option V
Glass Liner
is added for 240V.

SB-2M-STCC

-CC
-CC-V
Quartz Liner Available
Sampling Kit Available

37

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d 17 PLUS (R

d&F

The Apex Instruments Method 17 Sampling Kit


is a convenient package for sampling particulate
matter. Multiple fitting arrangements and filter
assemblies are available with an in-stack filter.

Add V to end of part number for 240V at no extra cost.

Method 17 Sampling Kit


Components Include:
In-stack Filter Assembly
Glass Fiber Thimbles

Schematic of EPA Method


17 Flexible Sampling Train

Method 5 Probe Sheath with Tube Heater


Method 17 Probe Liner w/ 3/8 Full Flow
Male Quick Connects
Unheated Sample Line with PFA Over braid
30 Split Umbilical Line
Power Box Adapter
Sample Case Adapter
Impinger Inlet Strain Relief
Impinger Box, Insulated
Coolant Reservoir
Stainless Steel
Nozzle Set
Stainless Steel
Impinger Assembly

- 17
- 17 -V

Schematic of U.S. EPA Method


17 Rigid Sampling Train

MET O 7C and 7

In Method 7C and 7 an integrated sample is passed


through a series of full-size orifice impingers that
contain an alkaline-potassium permanganate solution.
The sample rate is between 400 and 500 cc per minute,
normally three one hour samples are collected per test.
The MC-623 is the console of choice, however, a low
flow orifice adapter is offered for converting the XC-572
Method 5 source sampler console for low flow sampling.
The Method 7C sample is analyzed colorimetrically
and for Method 7D analysis is by ion chromatography.
Please inquire for additional details. Add V for
220VAC option.

PC10-3G

SB-3

GN-9AO-M7

Method 7 Accessories

38

GN-11

SB-8

C - 7C

Model

GN-8

escription

PC10-3G

3 ft CEM Probe Assembly, 5/8 Glass liner, 110 VAC

PLN-3G

3 ft Glass Probe liner, 5/8 OD with unground #28


grooved ball

GN-8

DoubleL Adapter, #28 unground sockets

GN-11

U-Tube, #28 unground sockets

GN-9AO-M7

Impinger Assembly, Stem with Orifice, 250 mL,


unground O-ring joints

GN-9A

GN-9A

Impinger Assembly, Plain Stem, 500


mL, unground O-ring joints, modified
Greenburg-Smith

GA-100

Umbilical Adapter (Gooseneck) , #28


Socket with thermocouple, mounting
bracket, 1/2 Male quick connects

SB-3

Impinger Box/Insulated Coolant Reservoir


Model 100, holds 4 impingers

SB-8

Modular Sample Frame with Probe Clamp


and Impinger Box Slides

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d 17 I -S

Replacement Seals

Part

In-Stack Filter Assembly using a 47 mm diameter Filter Element.

F -47
In-Stack Filter Assembly using
19mm x 90 mm Thimble Filter Element.

F -190
In-Stack Filter Assembly using
30mm x 100 mm Thimble Filter Element.

F -300
In-Stack Filter Assembly using
25mm x 90mm Thimble Filter Element.

F -2590

O-128V

Viton O-Ring for SFA-2590 (450 F)

O-324S

Silicone O-Ring for SFA-300 (500 F)

O-324G

Graphite O-Ring for SFA-300 (1000 F)

O-324V

Viton O-Ring for SFA-300 (500 F)

Q4213

Viton Quad Ring for SFA-190 (450 F)

O-223V

Viton O-Ring, 47 mm for SFA-47 (450 F)

O-223H

High Temperature Stainless Steel


O-Ring for SFA -47

SF-TT20

PTFE Thrust Ring for SFA-47 Filter


Assembly

O-324G

Graphite O-Ring for SFA-300 (1000+ F)

SFA-4

Inconel Version
F -47 C

(Nozzles not included)

INTEGRATE IN-STACK FILTER


ASSEMBLY KIT

The SGFA-47NK In-Stack Filter assembly


kit features the unique design combination of
borosilicate glass 47mm filter inlet with integrated
nozzle, allowing the option to weigh the glass
fiber filter media individually for Method 17 or very
similar to Method 5I by weighing the combined
nozzle, filter media with a support, O-Ring and
PTFE Tape. The kit includes the standard array
of seven nozzle sizes from 1/8 to 1/2.

Filters and Thimbles, page 46

Product

Glass Filter Inlet Integrated Nozzles

G-47N-ST

47 mm Glass Filter Inlet with ground #28 Socket on inlet

G-47N-4

47mm, with Attached Nozzle, Nozzle I.D. 1/8

G-47N-5

47mm, with Attached Nozzle, Nozzle I.D. 5/32

G-47N-6

47mm, with Attached Nozzle, Nozzle I.D. 3/16

G-47N-7

47mm, with Attached Nozzle, Nozzle I.D. 7/32

G-47N-8

47mm, with Attached Nozzle, Nozzle I.D. 1/4

G-47N-10

47mm, with Attached Nozzle, Nozzle I.D. 5/16

G-47N-12

47mm, with Attached Nozzle, Nozzle I.D. 3/8

G-47N-14

47mm, with Attached Nozzle, Nozzle I.D. 7/16

G-47N-16

47mm, with Attached Nozzle, Nozzle I.D. 1/2

Filter Inlet 47 mm Glass Filter Inlet with Integrated Nozzle.


Replace with nozzle diameter.

F -47

escription

I -S

The Apex Instruments GFA-2590 Thimble Holder is constructed completely from borosilicate glass for use with Conditional
Method for Ammonia (CTM-027) and accepts tapered 25 x 90mm thimbles, specifically manufactured for stack sampling. Does
not require O-Rings, for testing at higher temperatures. The borosilicate glass withstands temperatures up to 480C (900F).

GFA-2590K In-Stack Thimble

older Kit - Includes a selection of the


seven most commonly used nozzle inserts from 1/8 to 1/2 and one housing.
Kit is conveniently packaged in a foam-lined carrying case for protection. The
thimble holder connects directly to the end of the probe with a 5/8 tube union.
F -2590

Nozzle Insert - Replace with nozzle diameter. (Sizes 4-16).


Call for additional sizes

GFA-2590N
Filter Body - 5/8 Glass Filter Body
F -2590B
KTM-29 CLIP
GFA-2590N
Nozzle Insert

Nozzle
Size

5/8 Shank
GFA-2590B
Filter Body

Metal Taper Joint Clamp - A durable nickel plated steel clip that securely
holds the conical joint under pressure to withstand temperatures of up to
500C (932F).
-29
Call for Pricing of Quartz Components

39

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d 23 d LUXE PLUS

The Apex Instruments Method 23 (Modified Method 5) Source


Sampler Kit is utilized for Method 23 determination of dioxins and
furans (D/Fs) and/or Method 0010 Determination of Semi-Volatile
Organic Compounds. The sampling train is identical to the standard
Method 5 system with the addition of a water-cooled glass condenser
and an XAD absorbent module followed by a knockout impinger.
Additional glassware configurations are available.
Please call for information.

M23 Sampling Train

Select Meter Console and External Pump for M23 then add a kit.
Add V to part number for 240V option at an additional cost.

- 23
- 23

-V

Method 23 Source Sampler Kit Components:


6 Probe with Heater

Horizontal Condensers (2)

Glass Probe Liners (3)

XAD Traps (8)

Glass Nozzle Set

Submersible Recirculating Pump

Hot/Cold Box/Riser

Probe and Nozzle Brushes

30 Split-Back Umbilical

Programmed Calculator

Schematic of Method 23Sampling Train

Glassware, Deluxe Set

Requirements:
Borosilicate Glass or Quartz Nozzles and Probe Liners
are recommended.
Wrap XAD sorbent module with aluminum foil to shield
from radiant heat and ultraviolet rays that dechlorinate the
D/F isomers.
Sealing greases are not allowed. FEP O-Ring seals are
recommended and may be required by some agencies.
Flexible train requires heated flexible sample lines.

Method 23 Individual Accessories

40

MM5-P

MM5-PM

Coolant Pump Options


Product

Description

MM5-P

Submersible Coolant Pump, 110V

MM5-PM

Mini Submersible Coolant Pump, 110V

MM5-P220

Submersible Coolant Pump, 220V

Method 23 Glassware

Product

Conversion Accessories

Product

SB-4

Impinger Box/Insulated Coolant Reservoir Model 150,


Holds 8 Impingers

GNM-HC

MM5-P

Submersible Coolant Pump, 120V

Horizontal Condenser, #28


Unground Sockets,
Water Jacket, Hose Barbs

GNM-T

XAD Trap, #28 Ball & Socket Joints, Unground

GNM-VC

Vertical Condenser, #28 Unground


Sockets, Water Jacket Hose Barbs

GN-16

Glass Cap #28 Socket, Unground, to Seal XAD Trap

GNM-T

GN-17

Glass Plug #28 Ball, Unground, to Seal XAD Trap

KBS-29

Clip, Knock, Plastic out Impinger, Unground

XAD Trap, #28 Unground Socket


nd O-Ring Ball (Top),
Water, Jacket Hose Barbs

TL-7/5

Latex Tubing, 7/16 OD, 5/16 ID, Natural Color, Per Foot

GN-9AKS

Knock-Out Impinger Assembly,


Unground (for Horizontal MM5)

escription

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d 26A

Cl

The Apex Instruments Method 26A Sampling Train is used


for determination of hydrogen halide and halogen emissions. Method 26A is the isokinetic alternative to Method
26. This method is particularly suited for sampling sources
controlled by wet scrubbers emitting acid particulate matter.
The method requires a Method 5 sampling train with the use
of additional impingers, reagents and PTFE coated glass
fiber filter media. Please call for more information. Add V
to end of part number for 240V at no additional cost.

M26A Sampling Train

Method 26A Recommended Accessories


Product

Conversion Accessories

SB-4

Impinger Box/Insulated Coolant Reservoir Model 150, Holds 8 Impingers

NG-SET

Set of 7 Glass Nozzles - Sizes 4,6,8,10,12,14&16, Includes Case and Three 5/8 Glass Filled PFA Ferrules

NBT-1/2

Nozzle Brush, 1/2 diameter, PTFE Bristles

PBX-10T

10 foot Flexible PTFE Probe Brush Extension, Brush not Included

PBT-5/8

PTFE Probe Brush Tip (PTFE Barrel and Bristles), 5/8 inch Bristle Diameter

GN-9AK

Knock-Out Impinger, Short Stem, 500ml, Unground O-Ring Joints

GN-9AO

Impinger Assembly, Stem with Orifice & Plate, 500ml, Unground O-Ring Joints, Greenburg-Smith

GF-3TPG

82mm PTFE Coated Glass Fiber Filters - Hydrophobic, Low absorption of acid gases such as SOX or NOX
. 50/box (MFS PG60)

Schematic of Method 26A Sampling Train

When stack temperatures exceed 210oC (410oF) a one-piece glass


nozzle/liner assembly is recommended.

41

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

h d 29 M

The M
29 determination of metal emissions from hazardous waste incinerators involves a modification of the
Method 5 train. The sampling train is the same as a Method 5 particulate train with the addition of up to three impingers to
enhance the collection of metals of interest. The impinger train requires the SB-4 impinger case, glass nozzles, probe liners
and non-metallic union. The method has been
validated for the collection of 17 different metals.
Add V to end of part number for 240V option
at no additional cost.

Method 29 Recommended Accessories


Product

Conversion Accessories

SB-4

Impinger Box/Insulated Coolant Reservoir Model 150, Holds 8 Impingers

NG-SET

Set of 7 Glass Nozzles - Sizes 4,6,8,10,12,14&16, Includes Case


and Three 5/8 Glass Filled PFA Ferrules

GF-3QR

3 inch Quartz Fiber Filters-100/box (MFS QR100 82mm)

GN-9AK

Knock-Out Impinger, Short Stem, 500ml, Unground O-Ring Joints

GN-9A

Modified Greenburg-Smith Impinger (Plain), Unground

GF-3Q

3 inch Quartz Fiber Filters-25/box (Pallflex 8.26cm)

PBT-5/8

PTFE Probe Brush, Extension, 10 Foot Flexible (Brush Not Included)

PBX-10T

PTFE Probe Brush, 5/8 diameter, 4 length, 8-32 thread

NBT-1/2

Nozzle Brush, PTFE, 1/2 inch

M29 Sampling Train

Schematic of Method 29 Sampling Train


The standard glass filters are replaced with low background quartz filters. The impinger solutions are specific
for different metals. Recovered samples are digested and appropriate fractions are analyzed by various means;
inductively coupled argon plasma emission spectroscopy (ICPES), atomic absorption spectroscopy (AAS) or
graphite furnace AAS, depending upon sensitivity required or the matrix effects on the specific analyte.

42

ISOKINETIC SOURCE SAMPLING EQUIPMENT


O

h d (ASTM

6784-02) M

In the Ontario-Hydro Method (ASTM D6784-02) a sample is withdrawn from the flue gas stream isokinetically through
probe/filter system, maintained at 120OC (250OF) or the flue gas temperature (whichever is greater), followed by a series
of impingers in an ice bath. Particle-bound mercury is collected in the front half of the sampling train. Oxidized mercury
is collected in impingers containing a chilled
aqueous potassium chloride solution. Elemental
mercury is collected in subsequent impingers
(one impinger containing chilled aqueous acidic
solution of hydrogen peroxide and three impingers
containing chilled aqueous solutions of potassium
permanganate). Samples are recovered, digested,
and then analyzed for mercury using cold-vapor
atomic absorption (CVAAS) or flourescence
spectroscopy (CVAFS). The scope of the method
applies to determination of elemental, oxidized,
particle-bound and total mercury emissions from
coal-fired stationary sources with concentrations
ranging from approximately .05 to 100 ug/dscm.
The sample train is similar to EPA Method 5.

Ontario- ydro - Mercury Sampling Train

Ontario- ydro Recommended Accessories


Product

Conversion Accessories

SB-4

Impinger Box / Insulated Coolant Reservoir Model 150, Holds 8 Impingers

NG-SET

Set of 7 Glass Nozzles - Sizes 4,6,8,10,12,14&16, Includes Case and Three 5/8 Glass Filled PFA
Ferrules

BS28WS

#28 Ball Joint Clamp (Generic), Stainless Steel

NBT-1/2

Nozzle Brush, 1/2 inch diameter, PTFE Bristles

PBX-10T

10 foot Flexible PTFE Probe Brush Extension, Brush not Included

PBT-5/8

PTFE Probe Brush Tip (PTFE Barrel AND PTFE Bristles), 5/8 inch Bristle Diameter

GN-9A

Greenburg-Smith Impinger (with orifice), Unground

GN-9AO

Impinger Assembly, Stem with Orifice & Plate, 500ml, Unground O-Ring Joints, Greenburg-Smith

GN-11

U-Tube, #28 Unground Sockets

GF-3Q

3 Quartz Fiber Filters, 25/Box

Schematic of Ontario- ydro Method Sampling Train

43

ISOKINETIC SOURCE SAMPLING EQUIPMENT


P

-P

h d 201

Method 201A applies to the in-stack measurement of particulate matter (PM) emissions equal to or less than
an aerodynamic diameter of nominally 10 microns (PM10) and or 2.5 microns from stationary sources. A gas
sample is extracted at a constant flow rate through Apex instruments cyclone, which separates PM greater
than PM10.. PM .less than PM10 is collected on the in-line filter. In order to maintain a cut size of 10 microns
in the cyclone, the flow rate must be maintained at a constant, discrete value during the run. Apex cyclones
meets the specifications of Method 201A and allows use of the equations in Method 201A to calculate the
constant sample flow rate.

Introducing PM1 Cyclone

Apex Instruments now offers a cyclone designed for sampling very fine particulate matter in the
1.5 to 0.5 micron range. The cyclone is based on the cyclone V from the Multi-stage cyclone
system designed and calibrated by Southern Research Institute under contract for the EPA.
The design has been modified to accept the nozzles from the PM 2.5 cyclone, which has been
expanded to a set of 12 different size nozzles. The sample flow rate must be maintained, in which
the constant rate determines the actual D50 cut-point. The cyclone is followed by a 47 mm filter
assembly. Quartz or PTFE coated glass fiber filters should be used to minimize reactivity with
the flue gas. The cyclone and nozzles are constructed from grade 316 stainless steel with Viton
o-rings. Other materials are available upon request for corrosive or high temperature applications.

PM1 Cyclone Kit Components

The PM1 Cyclone is used for in-stack measurement of very fine particulate matter. The 47 mm
filter assembly outlet connector has a 5/8 outer diameter for easy installation Method 5 Probe
Assemblies. The cyclone kit is enclosed in a sturdy plastic case.
Product

1Packing List

escription

PM1-K

PM1 Cyclone Set Includes: Cyclone Body, 12 Nozzles, (PM2-NS), Filter


(SFA-47), Manual and Case

PM1

PM1 Cyclone Body Only, Stainless Steel with Viton O-Rings

PM2-NS

Set of 12 Nozzles for PM1 and/or PM2.5 Cyclone, Stainless Steel

PM2.5 Cyclone Kit

The PM2.5 Cyclone is used for in-stack measurement of particulate matter equal to or less than
2.5 microns. The shank has a 5/8 outer diameter for easy adaptation to the Method 5 Probe
Assemblies. The kit is enclosed in a sturdy plastic case with 12 nozzles.

PM2.5 Cyclone Kit Components


Product

2Packing List

escription

PM2-K

PM2.5 Cyclone Set Includes: Cyclone Body, 12 Nozzles, (PM2-NS),


Filter (SFA-47), Manual and Case

PM2

PM2.5 Cyclone Body Only, Stainless Steel with Viton O-Rings

PM2-NS

Set of 12 Nozzles for PM2.5 Cyclone, Stainless Steel

PM2-NSA

Add-On Set of 6 Nozzles (NS-7, 8, 9, 10, 11, 12) for upgrading PM2.5
Cyclone Existing Kits, Stainless Steel

O-024V

Viton O-Ring for PM2.5 Cyclone, (2 per cyclone).

O-024H

High Temperature O-Ring for PM2.5 Cyclone, Stainless Steel

MPT-6-181

Pitot Tip, 3/8 Tube, Stainless Steel Replacement for Standard


Method 5 Probe Assemblies

Alloy 600 Components Available. Call for Pricing.

Apex Expanded Nozzle Set


PM2-NS Nozzle Set Includes 1 Each

44

PM2-NS Nozzle Set Includes 1 Each

Product

Size

Product

Size

Product

Size

Product

Size

PM2-N1

.125 Size 1

PM2-N4

.172 Size 4

PM2-N7

.216 Size 7

PM2-N10

.274 Size 10

PM2-N2

.138 Size 2

PM2-N5

.188 Size 5

PM2-N8

.234 Size 8

PM2-N11

.296 Size 11

PM2-N3

.156 Size 3

PM2-N6

.200 Size 6

PM2-N9

.253 Size 9

PM2-N12

.320 Size 12

ISOKINETIC SOURCE SAMPLING EQUIPMENT


PM10 Cyclone Kit

PM10 is used for Method 201A testing and is designed for in-stack measurement of particulate matter equal to or less than 10
microns. The shank has a 5/8 outer diameter for easy adaptation to Method 5 Probe Assemblies. The cyclone kit is enclosed in a
sturdy plastic case with twelve nozzles (4 diameter port opening minimum). Call for High Temperature Alloy 600 PM10 Cyclones
and Filter Holders.

PM10 Cyclone Kit Components


Product

escription

PM10-K

PM10-K Cyclone Kit, Includes: Cyclone, 12 Nozzles Set (PM10-NS), 47mm


Filter Holder (SFA-47), Manual & Case

PM10

PM10 Cyclone Only, Stainless Steel with Viton O-Rings

PM10-NS

Set of 12 Nozzles for PM10 Cyclone (Now with 12 Nozzles)

O-032V

Viton O-Ring for PM10 Cyclone

O-032H

High Temperature Stainless Steel O-Ring for PM10, Cyclone

MPT-6-320

Extended Pitot Tip for PM10, SFA-300, and SFA-2590

PM10/2.5 Cyclone 12 Nozzle Set - 1 Each


10Packing List

Product

Size

Product

Size

Product

Size

Product

Size

PM10-N0

.125 Size 0

PM10-N3

.164 Size 3

PM10-N6

.215 Size 6

PM10-N10

.342 Size 10

PM10-N1

.136 Size 1

PM10-N4

.180 Size 4

PM10-N7

.233 Size 7

PM10-N11

.390 Size 11

PM10-N2

.150 Size 2

PM10-N5

.197 Size 5

PM10-N9

.300 Size 9

PM10-N12

.320 Size 12

PM10/2.5 Cyclone Kit

PM10/PM2.5 Set combines the in-stack measurement of particulate matter (PM) equal to or less
than an aerodynamic diameter of nominally 10 (PM10) and 2.5 (PM2.5 ) microns from stationary
sources. The sampling train and operation are identical to Method 201A except that the PM2.5
cyclone is inserted between the PM10 cyclone and the 47mm filter. The PM10 cyclone collects
particulate matter greater than PM10 while the PM2.5 collects PM less than PM10 and greater
than PM2.5. The in-line filter collects PM less than PM2.5 (6 diameter port opening minimum).

PM10/2.5 Cyclone Kit Components


Product

2.5-10

escription

PM2.5-10K

PM 2.5/10 Cyclone Kit Includes: PM10 Kit, with PM10/PM2.5


Nozzle, Cyclone Assembly, 47 mm Filter Assembly,
Stainless Steel, Adapters, Pitot & Case

PM2/10-CK

Connector Kit includes: GA-110 Strain Relief Adapter for PM2.5 and
PM10 Cyclones, NSB-16 Button Hook Adapter for connecting the
PM10/2.5 Cyclones, 10MSC5-S Connector, adapts NSB-16 to
PM2.5 Cyclone, 5/8 TU to 5/16 bevel seat, Stainless Steel,
and N-10UBNN SS Union, 5/8, Bored out .660 with
shoulder, Body only, No Nuts or Ferrules

PM2/10-CKI

Connector Kit includes: INCONEL EQUIVALENT TO: GA-110 Strain


Relief Adapter for PM2.5 and PM10 Cyclones, NSB-16 Button Hook
Adapter for connecting the PM10/2.5 Cyclones, 10MSC5-S Connector, adapts NSB-16 to PM2.5 Cyclone, 5/8 TU to 5/16 bevel seat,
and N-10UBNN Union, 5/8, Bored out .660 with shoulder, Body only,
No Nuts or Ferrules

SFA-47

Filter Assembly, 47mm, 5/8TU, Stainless Steel, Method 17 In-Stack


Filter Unit, 5/8 inch Tube Unions, uses 47mm diameter Filter Element

GA-110

Strain Relief Adapter for PM2.5 and PM10 Cyclones

NSB-16

Button Hook Adapter for Connecting the PM10/2.5 Cyclones

10MSC5-S

PM10/2.5 Connector, Adapts NSB-16 to PM2.5 Cyclone,


5/8 TU to 5/16 Bevel Seat, Stainless Steel

Recommended Accessories for Sampling with Cyclone Sets.


Power Box Adapter, Includes 1/2 inch
Mounting Clamp and 4 Pin Amphenol
to 3 Receptacles.

-3J

Extended Pitot Tip for PM10/2.5


Sampling, Tube Diameter 3/8,
Length 421 mm

-6-421

47mm Glass Fiber Filters, 100/


box (Whatman 934AH-4.7cm).

F-47

Sample Frame with Probe


Clamp & Impinger Box Slides

B-8

45

ISOKINETIC SOURCE SAMPLING EQUIPMENT


C

CI-700K Cascade Impactor Kit includes 7 stage impactor, a PRA-K pre-cutter, nozzles, interconnecting tube, glass fiber
filters (45 mm, 47 mm and GFDN filters) and foil collection plate.

CI-700-K

Stainless Steel Pre-Collector

Cascade Impactor 7 Stage 47 mm


filter outlet, Viton O-Rings, Foil
collection plates.

CI-700
Set of 7 Lightweight Stainless Steel
Foil Collection Plate Inserts.

CI-FP

Price

Description

PRA-K

Pre-Cutter Assembly Kit,


Includes Body, Cap, Outlet
Cap with Union, Nuts, Ferrules
and Set of 6 Nozzles

PRA-N4

1/8

PRA-N6

3/16

PRA-N8

1/4

PRA-N10

5/16

PRA-N12

3/8

PRA-N16

1/2

PRA-NS

Set of 6 Pre-Collector
Nozzles, Sizes 4-16

CI-700-K

PRA-K
CI-700

Sz

S f w

Windows-based Cascade Impactor Data Reduction System (WINCIDRS) calculates particle


size distribution of stack particulate matter (PM) taken with the Cascade Impactor, as well as
particle-sizing cyclones. Developed by stack particle analysis experts, this software reduces
the time and chances of error involved with reducing particle sizing data. (The PM10/2.5 Software
Program (PM-2.5-10C) is extracted from WinCIDRS and simplified for use only with PM10 and
PM2.5 cyclones. The calculations are similar to the WinCIDRS, scaled-down specifically for
cyclone data reduction. The calculations are intensive enough to demand computer software.)

unctions

Calculates each stages aerodynamic cut point and DP50, needed to reduce particle size data.
Calculates and Stores ancillary data, such as dry gas composition and moisture content.
Reduces velocity traverse data.
Aids in selection of sample flow rates and ideal nozzle size.
Calculates flow rates and dwell times required for PM10 and PM2.5 sampling traverses.
Calculates fractional efficiencies of control devices from samples obtained at inlets and outlets.

Data Reduction Software

46

Product

Description

PM-2.5-10C

Particle Sizing Software for PM2.5 and PM10 Cyclones

INCIDRS

ISOKINETIC SOURCE SAMPLING EQUIPMENT


Method 202 (

ry I p nger Method)

This isokinetic method is used to measure Condensable Particulate Matter (CPM) from stationary source emissions after
particulate matter has been removed by a heated filter, such as in Method 5, 17 or 201A. The CPM is collected in dry
impingers. The impinger contents are purged with nitrogen (N2) immediately after sample collection to remove dissolved
sulfur dioxide (SO2) gases from the impinger. The organic and aqueous fractions are dried and the residues are weighed.
The total of the aqueous and organic fractions represents the CPM.

Components List
FA-3U-18K

Method 202 Sampling rain

3 filter assembly, ungrounded


glass with 90 degree inlet and
outlet, open style alum clamp.
With rubberized silicone
filter support.

SB-4S

-9AKSA

Impinger box - insulated


coolant reservoir model 150,
holds 8 impingers.

Knock-out impinger assembly,


ungrounded (for HorizMM5).
Includes: GN-9AKSB (Bottle),
GN-9AKS-I (Short Stem),
GN-9AKS-IL (Purge Stem).

A-28S4

Stainless steel adapter, 28mm


socket to 1/4 FNPT, 3 long
400F rating.

F-3 M

3 PTFE membrane filter - 50 per box


(Palifex 90mm).

-VC M-M202

M202 Spiral Condenser, #28 Ball and


Socket. Water Jacket Hose Barbs,
High Moisture sources above 15%.

FI ter nd
rge
Ad pter
Filter System for
Purging Method 202.
Call for more details.

MM5- M

SFA-116IL

Stainless steel filter housing in-line 1/4


FNPT, 3 long 400F rating. Size: 1 Micron.
Other sizes available.

SFA-1101

316L mesh stainless steel elements are


recommended for filtration of heavily
contaminated gases, liquids, polymers,
and steam. Temperature range of -65 F to
1000F. Withstands 1000 PSIG differential.

Mini submersible coolant pump, 110V.

MM5-

Schematic of the M202 Sampling rain

Submersible coolant pump, 110V.

GN-VCHM-M202
GN-8

-9AKS-IL

Purge
Stem

-9AKS-I

See Page 45
for PM10-2.5 Configurations

See Page 40
for Available Pumps

-9AKSB (Bottle)
-9AKS-I ( Short Stem)
-9AKS-IL ( urge Stem)
Can be Sold Separately

For Knockout
GN-9AKSA

-9AKSB

See Page 28

A for Full-Part

Assembly
Break-Down
Method 202 (Cont n ed on

ext

ge)

47

IS KI

IC S U C SAM LI

Method 202 S
Quantity

p ng A

roduct

QUI M

or e

escription

SB-4SD

Two Section Divided Impinger Box

GN-VCHM-M202

Vertical Condenser #28 Socket to M202 Spiral Condenser, #28 Socket


both ends Water Jacket Hose Barbs, High Moisture Source above 15%.

GN-9AKSA

Glass Knock-out Impinger Assembly, Unground, (for HorizMM5) included


with Long / Short Stem

GNFA-3U-18K

CPM 3 Filter Assembly including Flexable TC

GF-3TM

TPFE Membrane Filters with Support, 1 Micron Pore Size, 50/Box

MM5-P

MM5-P Submersible Coolant Pump, 110V

MM5-PM

Mini Submersible Coolant Pump, 110V

SB-8

Sample Frame with Probe Clamp

Method 202

rge A

or e

SFA-116IL

Stainless Steel Filter Assembly, 3 L In-Line

SFA-1101T

Stainless Steel FIlter Element

GA-28S4

#28 Socket Bored Purge Adapter

GN-9AKA

Knock-out impinger assembly, ungrounded (for


HorizMM5). Includes: GN-9AKSB (Bottle), GN-9AKS-I
(Short Stem), GN-9AKS-IL (Purge Stem).

ex
ent Chro
r n & A e or e

FA I p nger

Call for more details.

exavalent Chromium Method 0061 igh


or Low emperature Source Sampling Kit

Method 0061 Hexavalent Chromium Emissions from Stationary Sources


determines hexavalent chromium emissions from hazardous waste
incinerators, municipal waste incinerators, municipal waste combustors and
sewage sludge incinerators. Isokinetically collected with a train where the
impinger reagent is recirculated continuously. Samples are analyzed with an
ion chromatograph. Method 0061H Hexavalent Chromium High Temperature
Source Sampling Kit is used as an alternative for temperatures above 150C
(300 F). Option V is added for 240 V.

SK-0061H

FI ter nd
rge
Ad pter
Filter System for
Purging Method 202.

4 Stainless Steel Probe


Assembly (Not Heated)
Glass Probe Liners (2)
Glass Nozzle Set
PTFE Impingers

SK-0061H-V
-10U

907-049

Schematic of Method 0061

48

Sampling rain

30 Split Umbilical
Impinger Box
Peristalic Pump
PTFE Membrane
Sample Frame

ISOKINETIC SOURCE SAMPLING EQUIPMENT


F

M d

Apex Instruments offers a wide range of filter media to meet any sampling requirements. Listed below are the standard media
and sizes that Apex Instruments normally stock. Additional materials and sizes are available upon request.

Glass Fiber Filters are most commonly used filters for particulate sampling. All of the glass fiber filters are binder free and
exhibit at least 99.9% efficiency for 0.3 micron dioctyl phthalate (DOP) smoke particles. Not recommended for metals analysis.

Grade E F

Ideally suited for suspended solids analysis and high volume air monitoring applications. Softening point of glass fiber is 500C,
therefore upper limit temperature in use is 475C. Low fiber shedding improves quality assurance of test results. high loading
capacity. This media meets requirements for standard method 2540D and EPA Method 160.2 for establishing water quality in
suspended solids content.

G
Model

Q
escription

Quartz Fiber Filters are manufactured from pure quartz without a binder and are frequently used for sampling for metals
analyses and acidic gases.

GF-2

2 inch Glass Fiber Filters-100/box


(934AH-5.5cm)

GF2X6.5

2x6.5 inch Glass Fiber Filters-100/box


(934AH)

Model
GF-2Q

2 inch Quartz Fiber Filters-25/box

GF-3

3 inch Glass Fiber Filters-100/box


(934AH-8.26cm)

GF-25Q

25mm Quartz Fiber Filters-100/box

GF-3Q

3 inch Quartz Fiber Filters-25/box


(Pallflex 8.26cm)

GF-4Q

4 inch Quartz Fiber Filters-25/box


(Pallflex 11 cm)

GF-45Q

45mm Quartz Fiber Filter-100/box

GF-47Q

47mm Quartz Fiber Filter-25/box


54mm Quartz Fiber Filters-25/box
(Pallflex 54mm)

GF-4

4 inch Glass Fiber Filters-100/box


(934-AH-11cm)

GF-45

45mm Glass Fiber Filters-100/box


(934-AH-45mm)

GF-47

47mm Glass Fiber Filters-100/box


(934AH-4.7cm)

escription

GF-63

63.5mm Glass Fiber Filters-100/box


(934-AH-63.5mm)

GF-54Q

GF-90

90mm Glass Fiber Filters-100/Box


(934AH-9.0cm)

GF-63Q

63.5mm Quartz Fiber Filters-25/box


(Pallflex 63.5mm)

GF-2E

2 inch Glass Fiber Filters-100/box Grade E

GF-3QR

GF-3E

3 inch Glass Fiber Filters-100/box Grade E

3 inch Quartz Fiber Filters-100/box


(MFS QR100 82mm)

GF-4E

4 inch Glass Fiber Filters-100/box Grade E

GF-4QR

4 inch Quartz Fiber Filters-100/box


(MFS QR100 110mm)

GF-25E

25mm Glass Fiber Filters-100/box Grade E

GF-47QR

GF-47E

47mm Glass Fiber Filters-100/box Grade E

47mm Quartz Fiber Filters-100/box


(MFS QR100 47mm)

GF-90QR

90mm Quartz Fiber Filters-100/box


(MFS QR100 90mm)

49

ISOKINETIC SOURCE SAMPLING EQUIPMENT


PTFE C

PTFE Coated Glass Fiber Filters are constructed from borosilicate microfibers and bonded with PTFE. The filters can be folded
& handled without loss of fibers. Great for especially low loading rates. Specifically recommended for Method 26 & PM10 sampling.
Product

Product

escription

escription

GF-2T

2 inch PTFE Coated Glass


Fiber Filters-100/box

GF-90T

90mm PTFE Coated Glass Fiber Filters-100/box


(Pallflex 90mm)

GF-3T

3 inch PTFE Coated Glass Fiber


Filters-100/box (Pallflex 82.6mm)

GF-90T

90mm PTFE Coated Glass Fiber Filters-100/box


(Pallflex 90mm)

GF-4T

4 inch PTFE Coated Glass Fiber


Filters-100/box (Pallflex 11cm)

GF-3TPG

GF-25T

25mm PTFE Coated Glass Fiber


Filters-100/box (Pallflex 2.5 cm)

3 inch PTFE Coated Glass Fiber Filters-50/box (MFS


PG60) 82mm-Hydrophobic, Low absorption of acid gases
such as SOX or NOX.

GF-4TPG

GF-47T

47mm PTFE Coated Glass Fiber


Filters-100/box (Pallflex 4.7cm)

4" PTFE Coated Glass Fiber Filters-50/box (MFS PG60)


110mm-Hydrophobic, Low absorption of acid gases such
as SOX or NOX.

GF-90T

90mm PTFE Coated Glass Fiber


Filters-100/box (Pallflex 90mm)

GF-47TPG 47mm PTFE Coated Glass Fiber Filters-100/box (MFS


PG60) 47mm-Hydrophobic, Low absorption of acid gases
such as SOX or NOX.

PTFE FILTER MEMBRANES


Model

GF-25TPG 25mm PTFE Coated Glass Fiber Filters-100/box (MFS


PG60) 25mm-Hydrophobic, Low absorption of acid gases
such as SOX or NOX.

escription

TF1121

PTFE Membrane, 47mm,


0.45 Micron (10/pack)

TF1131

PTFE Membrane, 47mm,


1-2 Micron (10/pack)

Model
TF1165

PTFE Membrane, 25mm, 30-60 Micron (10/Pack)

PTFE Membrane, 47mm,


5-6 Micron (10/pack)

GF-3TM

3 inch PTFE Membrane Filters-50/box (82.6mm) PTFE


filter media provides durability for hostile acid aerosol
monitoring. 1.0m pore size membrane.

TF1141

I -S

PTFE FILTER MEMBRANES


escription

Apex Instruments stocks a variety of Fiber Thimbles for in-stack particulate sampling. The thimbles
are seamless, high purity filters and available from a choice of two different types of fibers: Borosilicate
glass and quartz. Borosilicate glass fiber thimbles are acid washed to reduce the trace metal content to
an absolute minimum. Quartz fiber thimbles are strengthened with alumina and are prefired at 900C
for 2 hours during manufacturing to stabilize the weight prior to use. The gas collection efficiency of the
thimbles is 99.9% (0.3 micron DOP). The 25 x 90mm thimbles are specifically manufactured for stack
sampling and tapered for ease in loading. Cellulose thimbles are available upon request.
Q

Model

GLASS F

T
escription

Model

GF-2590Q

FILTER THIMBLES
escription

GF-190Q

19X90mm Quartz Fiber Filter


Thimble-25/box (For SFA-190)

GF-190

19x90mm Glass Fiber Filter


Thimble-25/box (For SFA-190)

GF-300Q

30x100mm Quartz Fiber Filter


Thimble-25/box (For SFA-300) grade 88R

GF-2590

25x90mm Tapered Glass Fiber


Thimble -10/box (For SFA-2590) Grade 86R

GF-2590Q

25x90mm Tapered Quartz Fiber


Thimble-10/box (For SFA-2590) Grade 88R

GF-300

30x100mm Glass Fiber Filter Thimble-25/box


(For SFA-300) Grade 86R

PTFE F

PTFE Filter Membranes are produced of pure PTFE resins. They withstand the most severely corrosive conditions at temperatures
as high as 500F (260C) and down to the cryogenic range. The membrane is hydrophobic and maintains its strength wet or dry.

(C

Alundum Thimbles are used for in-stack filtration for process engineering studies when a large sample is needed for analyses.
These thimbles are made from fused alumina oxide and remain very constant in weight and can be re-used an infinite number
of times. There are two different porosity thimbles that can be used in the SFA-300 thimble holder. The medium porosity retain
particles 5 micron and larger and the coarse retain particles 20 micron and larger.
Model

50

escription

GF-300C

Alundum Thimble, medium porosity, 5+ micron retention, 34x100ml,


round bottom, fits SFA-300 use with additional O-ring, O-123V.

GF-300-C

Alundum Thimble, COARSE porosity, 20 micron retention, 34x100ml,


round bottom, fits SFA-300 use with additional O-ring, O-123V.

GF-300C

ISOKINETIC SOURCE SAMPLING EQUIPMENT


S
N

R
B

NB-5

Apex Instruments Nozzle


Brushes feature stainless
steel handle and nylon
bristles. Super flexible for
NB-3
cleaning button hook
nozzles with eye tip to reduce
scarring of the nozzle.
Model

NB-8

hS

The NB-SET Nozzle Brush Set includes


one each of the three most popular sizes
in a convenient carrying tube. (#3,#5,#8)

NB-SET

PTFE N

NBT-1/2

NBT-1/2

escription

NB-3

3/16 diameter, Nylon Bristles

NB-5

5/16 diameter, Nylon Bristles

NB-8

1/2 diameter, Nylon Bristles

NB-SET

Modular Probe Brush Set

The PBX-S Modular Probe Brush Set


contains two of the 5/8 stainless steel twisted
wire brushes with nylon bristles and a total of
13 in stainless steel extensions.

PBX-S

PTFE Probe Brush

All PTFE construction. The PBT-5/8


diameter with four spiral rows of black
PTFE bristles. Over all length is 2. The
shaft is 1/4 diameter with 8-32 female
threads. PTFE Barrel and PTFE Bristles.

PTFE Probe Brush Extensions

The flexible PTFE Probe Brush


Extension attaches to the PBT-5/8 or
PB-5/8. Made with 8/32 threads with a
phenolic knob. Please specify length.

PBT-5/8

PBX-S

PBX- T

Model
Model

Nozzle Brush NBT-1/2 is constructed


of pure PTFE featuring a 1/8 diameter
shaft with 1/2 long soft PTFE bristles.

escription

PB- 5/8A

Probe Brush/Stainless
Steel, Nylon Bristles &
Allen Set Screw (HD1088)

PBX-2

2 Probe Brush
Extension, Stainless Steel

PBX-3

3 Probe Brush
Extension, Stainless Steel

PBK-832

Probe Brush Knob

PBT-5/8

B-1

B-1

B-3

B-4

Filter Recovery Brush


Filter Brush, 3/16 diameter, Stainless
Steel Handle and Nylon Bristles, 5/16.

B-3

Policeman
Rubber Policeman with
18 Delrin Handle

B-4

escription

PBX-4T

4 PTFE Probe
Brush Extension

PBX-6T

6 PTFE Probe
Brush Extension

PBX-8T

8 PTFE Probe
Brush Extension

PBX-10T

10 PTFE Probe
Brush Extension

PBX-12T

12 PTFE Probe
Brush Extension

Impinger Bottle Brush


Impinger Bottle Brush
with Plastic Handle and
Nylon Bristles.

Brush Sold
Separately

B-2
Flask Brush
Flask Brush, Stainless
Steel Handle and
Nylon Bristles.

B-2

Sample Line Brush


20 ft.Teflon Sample
Line Brush, 1/8 diameter
rod with 1/2 long bristles

B-5

51

ISOKINETIC SOURCE SAMPLING EQUIPMENT


S

A
Aluminum Weighing
ishes (70 ml)
100/pack.

25433-062
Aluminum Weighing
100 Pack (12.1 cm)

250ML-CYL-PMP

25373-1100

ishes

Petri ish 150x15mm


(4 Diameter), 10/pack

12175-001

Graduated Cylinder
250ml, Glass

25373-187

Funnel

TW-1

Polypropylene Funnel
Top Diameter 108mm.

Nylon Tweezers

30255

TW-1

Graduated Cylinder
250ml, Plastic

Petri ish 100x15mm


(3 Diameter),
25/pack.

250ML-C L-PMP

Cotton Balls
Synthetic Cotton Balls
(For Impinger Outlet Filter),
300/bag

250ML-CYL

Parafilm M, Laboratory Sealing


Film, Roll is 2 x 250 ft.

PARA-2X250

MS-1

Wide Mouth Bottles for Easy Filling


and Pouring. The HDPE bottle with
polypropylene closures are made of
FDA compliant material. Recycling
code molded into base of bottles.
Simple to pour-wide mouth bottles.
Chemically resistant. Leak proof, firm.
Excellent for packaging chemicals,
pharmaceuticals and adhesives.

FEP W

hB

500mL Wash Bottles, FEP.

WB-500F

WB-500FEP

125 mL vw/Wide Mouth, w/Cap.

WAS

500mL Plastic Wash Bottles

WB-1W

WB-5

250 mL w/Cap.

WB-2
250 mL w/Wide Mouth.

WB-5P

WB-2 W
16oz. / 500 mL w/Wide Mouth.

WB-4

1000 mL w/Wide Mouth.

WB-10
1000 mL w/Wide Mouth.

B-250

WB-1000 W
WB-2P/with Cap
250ml

52

250mL Glass Sample


Bottles with PFA-Lined Lid.
Case of 12.

WP-4B/with Cap
500ml

GSB-250

ISOKINETIC SOURCE SAMPLING EQUIPMENT


d

Acrylic Desiccator Cabinets feature adjustable shelves with grooves for positioning,
removeable lip tray, gasketed door, built-in hygrometer. Cabinets do not include
Desiccant, order separately.

Features
Patented Sealed Construction is
Airtight, Dust and Moisture Free.
Portable and Stackable with a
Small Footprint.

Embedded UV Protection and


Superior Chemical Resistance.
Built-in Hygrometer for Quick
Check on RH Levels.
Rugged Construction with Sturdy
Latches and Lock Provisions.
31000

Model

escription

imensions

Features

DES-10000

Desiccator Cabinet

8.4 x 13.4 x 16.3

Gasketed door, built in hygrometer, 0.75 cu.ft.

DES-21000

Desiccator Cabinet

12.4 x 13.4 x 16.3,

Gasketed door, 2 shelves, built in hygrometer 1.17 cu.ft.

DES-21115

Auto-Desiccator
Cabinet

12.4 x 13.4 x 16.3

Gasketed door, 2 shelves, built in hygrometer 1.17 cu.ft. 110V

DES-21115V

Auto-Desiccator
Cabinet

12.4 x 13.4 x 16.3,

Gasketed door, 2 shelves, built in hygrometer 220V fan,


1.17 cu.ft.

DES-31000

Desiccator Cabinet

16.4 x 13.4 x 16.3,

Gasketed door, 3 shelves, built in hygrometer stackable

DES-31115

Auto-Desiccator
Cabinet

16.4 x 13.4 x 16.3,

Gasketed door, 3 shelves, built in hygrometer stackable, 110V

DES-31115V

Auto-Desiccator
Cabinet

16.4 x 13.4 x 16.3,

Gasketed door, 3 shelves, built in hygrometer 220V fan

DES-40000

Desiccator Cabinet

13.4 x 20.4 x
16.3,

Gasketed door, 2 shelves, horizontal Profile

DES-41115

Auto-Desiccator
Cabinet

20.4 x 13.4 x 16.3

Gasketed door, 3 shelves, built in hygrometer

DES-41220

Auto-Desiccator
Cabinet

20.4 x 13.4 x 16.3,

Gasketed door, 3 shelves, built in hygrometer, 220V fan

www.belart.com

dESI- AC

ONTAINER

Desiccator with a vacuum pump is ideal for drying, preserving, storing, and even shipping
samples. Vacuum pump built into the top removes air with manual strokes. Rubber O-ring
sealed cover maintains vacuum. Achieves a vacuum of better than 200 inches of water
(15 inches of mercury). A release button on top allows air into the container to remove
the lid. Sample Humidity Sponges desiccant drying packets are included. O-ringsealed cover maintains vacuum. Achieves a vacuum of better than 200 inches of water
(15 inches of mercury A release button on top allows air into the container to remove the
lid. Keep powder dry. Plastic container is ideal for storing chemicals, powders, tissues,
plant sections, electronics, and weighing samples. Vacuum and desiccants keep material dry. Supplied with a vacuum indicating button that confirms interior vacuum and a dial
hygrometer that displays 0 to 100% relative humidity with a resolution of 2%RH.
Dimensions: HxWxD: 11 x 9 x 10.

ES-3164

-3164

53

ISOKINETIC SOURCE SAMPLING EQUIPMENT


S

Apex Instruments Silica Gel is primarily used for drying sample gas prior to measurement and can
absorb moisture 40% of its weight. The silica gel can be regenerated by drying in an oven and used
over and over again.
SILICA GEL
3-5mm Bead, Indicating, 2.3Kg.

-3/5B
SILICA GEL
Blue Indicating, 12/case, 250 ml per bottle.

SG-KIT

SILICA GEL
3-5 mm Bead, Bulk
55 L , C

-3/5B-55
SG-3/5B-55

SG-3/5B

dA

The activated alumina is primarily used for air drying


at low temperature applications, 5.5 lb. container.
80% Activated Alumina (White). 1/8 Diameter Beads.
20% Silica Gel (Blue) 3-5 mm Beads.

Aluma-sorb
Adsorption Housing, 1/4 FNPT Fittings.
Without Sorbent.

Aluma-sorb

A -610R

-610

RIERITE

Apex Instruments carries both non indicating and indicating DRIERITE. (anhydrous calcium sulfate) Economical to use, it
can be regenerated repeatedly. The indicating DRIERITE is impregnated with cobalt chloride: blue when dry and changes
to pink upon absorption of moisture.
Part Number

escription

14005

DRIERITE, Nonindicating 10-20 Mesh, 5 Lbs. (2.3 kg)

23005

DRIERITE, Indicating 8 Mesh, 5 Lbs. (2.3 kg)

24005

DRIERITE, Indicating 10-20 Mesh, 5 Lbs. (2.3 kg)

26840

DRIERITE, Cartridge, 50g H2O Capacity

26809

Mounting Clip for Use with Gas Drying Units

24005

54

14005

ISOKINETIC SOURCE SAMPLING EQUIPMENT


B

EJ-S
Easy to read LCD Display
with Backlight
Percentage and Counting
USB or RS-232 Interface Optional
Battery Operated (4 x AA not included)
AC Adapter Included
Pan Size: 5 x 5.5
Check-Weighing Capacity
5 Year Warranty

BAL-EJ1500

1500g x 0.1 g.

BAL-EJ3000

3100g x 0.1 g.

BAL-EJ6100

6100g x 0.1 g.

BAL-EJ02

USB Interface with Cable

BAL-EJ12

Carrying Case

h
d

BAL- 1000ASTM

Weight for Electronic Balance.


ASTM GRADE 7

1 kg.

BAL- 2000ASTM

Weight for Electronic Balance.


ASTM SHAPE

2 kg.

BAL- 5000ASTM

Weight for Electronic Balance.


Class F, meet Tolerances of NIST

5 kg.

wi h

i i

55

ISOKINETIC SOURCE SAMPLING EQUIPMENT


B
R-S
Percentage and Counting Modes.
Digital Preset Tare.
One Touch Printing.
Last Digital Suppression.
Standard Underhook.
Optional Rechargeable Battery Pack.
GLP/LIMS/ISO Compliant.
RS-232C Standard.
5 Year Warranty.

-HR60-

60g x 0.1mg with RS-232C.

3.3

120-

120g x 0.1mg with RS-232C.

3.3

200-

210g x 0.1mg with RS-232C.

3.3

202i

220g/51g x 0.1mg/0.01mg
Semi-Micro with R-232C.

3.6

Analytical Balances - Calibration Weight Set


d
- 1-100

Weight Set - 1mg-100g


Stainless Steel Calibration Weight Set for Lab Use. Set of 9
Weights Plus Fractional Weights in Wooden Storage Box.
Note: Please check with State Department of Weights and Measurements for calibrations.

56

ISOKINETIC SOURCE SAMPLING EQUIPMENT


M

Apex performs both calibrations using a wet test meter and bell-prover primary standard. Calibration services are available
from Apex Instruments on a fee per console basis. Extra charge for low flow. All console and dry gas meter calibrations are
conducted in accordance with U.S. EPA standards. Apex Instruments calibrates source sampler consoles, reference dry
gas meters, orifices and pitots.

Calibration being performed with Wet Test Meter


G

Model

escription

DGR-2VER

Verification of DGM for Secondary Reference, 2 Point Verification of Previous Calibration

DGMC-5A

Pre-Test 5 Point Calibration for Compatible Meter Consoles

DGMC-3A

Post Test 3 Point Calibration for Meter Consoles

CAL-ORF

Orifice Calibration, 3 Point

GM-AP25SR

GM-110SR

G
S
d
R
M
(E
h)
Dry Gas Meter Secondary Reference Meter
(Standard) with 15 pt cal, valve, 5 hose,
1/2 Quick Connect. Used for calibrating
Method 5 Source Sampler Consoles.

-110

S
d
R
M
(M
)
Dry Gas Meters Secondary Reference Meter
(Metric AP25) with 15 pt cal, valve, 5 hose, 1/2
Quick Connect.Used for calibrating Method 5
Source Sampler Consoles.

25

57

ISOKINETIC SOURCE SAMPLING EQUIPMENT


C

U.S. EPA allows critical orifices to be used as calibration standards. The orifice calibration set contains five of our critical
orifices with 1/2 quick connects and software. Recalibration recommended annually. Calibration Orifice Set, 5 Calibrated
Critical Orifices and Spreadsheet Diskette for Method 5.

5C -

....$510.00

Orifice Set Contains the following:


Model

escription

M5CO-40

Calibration Critical Orifice, Size 40, Flow Rate.


~.31cfm (~8.8 lpm) with 1/2 Male QC

M5CO-48

Calibration Critical Orifice, Size 48, Flow Rate.


~.46cfm (~13.0 lpm) with 1/2 QC

M5CO-55

Calibration Critical Orifice, Size 55, Flow Rate.


~.61cfm (~17.3 lpm) with 1/2 QC.

M5CO-63

Calibration Critical Orifice, Size 63, Flow Rate.


~.79cfm (~22.4 lpm) with 1/2 QC.

M5CO-73

Calibration Critical Orifice, Size 73, Flow Rate.


~1.1cfm (~31.14 lpm) with 1/2 QC.

Available on CD

CALIBRATION EQUIPMENT AN SERVICES


PRECISION WET TEST METERS
The Model W-NK Wet Gas Meter is a net-volume type integrating flowmeter that employs
a drum as the metering element. As the drum is sealed with water or other fluid, the
Model W-NK provides the measurement of any gas irrespective of the gas specific gravity
and viscosity. Further, since this gas meter permits the measurement of very small flows,
exhibits high reproducibility, and offers various other excellent features, it properly serves
as a standard as well as a testing instrument.
The Best Standard for Calibration of

ry Gas Meters.

W-NK

Different Models Available.


Model A

Weight

eight

Width

epth

W-NK-0.5A

Max Flow 5 LPM, 0.5 Liter per Revolution

4.5kg

420

290

190

W-NK-1A

Max Flow 10 LPM, 1 Liter per Revolution.

6.0kg

450

315

210

W-NK-2A

Max Flow 20 LPM, 2 Liter per Revolution

9.0kg

390

350

255

W-NK-2.5A

Precision Meter, 2.5 Liter Capacity, 5 to 1500 L/HR

9.0kg

390

350

255

W-NK-5A

Precision Meter, 5 Liter Capacity, 5 to 3000 L/HR

25kg

575

455

295

W-NK-10A

Precision Meter, 10 Liter Capacity, 20 to 6000 L/HR

35kg

656

535

380

Model B
W-NK-0.5B

58

escription: Shinagawa Precision Wet Test Meter

escription: Shinagawa Precision Wet Test Meter


Max Flow 5 LPM, 0.5 Liter per Revolution, Corrosion Resistant

Weight
4.5kg

eight
420

Width
290

epth
190

W-NK-1B

Max Flow 10 LPM, 1 Liter per Revolution, Corrosion Resistant

6.0kg

450

315

210

W-NK-2B

Max Flow 20 LPM, 2 Liter per Revolution, Corrosion Resistant

9.0kg

390

350

255

W-NK-2.5B

Precision Meter, 2.5 Liter Capacity, 5 to 3000 L/HR,


Corrosion Resistant

9.0kg

390

350

255

W-NK-5B

Precision Meter, 5 Liter Capacity, 5 to 3000 L/HR,


Corrosion Resistant

25kg

575

455

295

W-NK-10B

Precision Meter, 10 Liter Capacity, 20 to 6000 L/HR,


Corrosion Resistant

35kg

656

535

380

ISOKINETIC SOURCE SAMPLING EQUIPMENT


CALIBRATION EQUIPMENT AN
N

SERVICES
P

Geometric of Type-S Pitot Tube to Method 2.

-C lWind Tunnel of Type-S Pitot Tube to Method 2.

-C

-W

ial Calipers are used for measuring nozzle diameter and inspection
of pitots. Dial Caliper, 0-6/ 150mm Direct inch/Metric Conversion.

5C-3

Th

This Thermocouple Simulator/Calibrator is convenient for checking the accuracy of most


Controllers and Temperature Displays. Whe Cold Junction Compensated, is calibrated without
External Compensators or Icebaths the Simulator Source is designed for Type-K Thermocouples and has 22 precise test points.

5C-520

M5C-520

PITOT AU IT EQUIPMENT & MANOMETERS

M-M100
M5C-2
INC-A300
A300 L

I d

Pendulum Style Inclinometer for


the Calibration of Type-S Pitots.

Bulls Eye Level is 1/2 diameter and


used for pitot calibrations. Comes with
thumb screws for clamping to pitot.

C- 300

5C-2

hAN

EL

LCD DISP., Digital Manometer, Method

2, Hand held, 0-10 inch H2O Selectable


Range, English/Metric.

-28-10

Software and cable for Digital


Manometer, HM28 series.

M-28-10

hAN

EL M

Meriam Handheld, LCD DISP


Digital Manometer, Hand held, 0-28 inch
H2O Selectable Range, English/Metric,
with certificate of NIST traceability.

- 100

DP-CALC Micromanometer makes differential


pressure measurements, static, total, and velocity
pressures as well as pressure drops across filters,
coils, fans, and diffusers. Differential and static
pressure from -15 to +15 in. H2O (-3735 to +3735
Pa) lightweight and durable design with an easyto-read display, certificate of NIST traceability.

-5825

-28-1

59

ISOKINETIC SOURCE SAMPLING EQUIPMENT


MONORAILS
h

(Threaded pipe flanges are available in 3,


4 or 6, stainless steel or aluminum.) Note:
The chain must be attached to the stack so
that the chain angle to the monorail is no
less than 30 (45 is recommended).

PF- CS
Pipe Flange
Monorail with Chain

Heavy Duty Steel Monorail with Chain, L-Bracket and Hardware (for use with probes).
LF

Part #

P1000-6

P1000-7

P1000-8

P1000-9

P1000-10

P1000-12

Probe
Size

For use with probes


over 6

For use with probes


over 7

For use with probes


over 8

For use with probes


over 9

For use with


probes over 10

For use with


probes over 12

10

PART #

Monorail with Cable and Chain

LF

P1001-10

MONORAIL, 10FT, STEEL Heavy Duty, Double Channel,


W/CHAIN, L-Bracket & Hardware.

10

P1001-12

MONORAIL, 12FT, STEEL Heavy Duty, Double Channel,


W/CHAIN, L-Bracket & Hardware.

12

P1001-14

MONORAIL, 14FT, STEEL Heavy Duty, Double Channel,


w/ Adjustment Chain, L-Bracket & Hardware.

14

P1001-16

MONORAIL, 16FT, STEEL Heavy Duty, Double Channel,


w/Cable, Adjustable Strap, L-Bracket & Hardware.

16

P1001-17

MONORAIL, 17FT, STEEL Heavy Duty, Double Channel,


w/Cable, Adjustable Strap, L-Bracket & Hardware.

17

P1001-18

MONORAIL, 18FT, STEEL W/CHAIN Heavy Duty, Double


Channel, w/Cable, Adjustable Strap, L-Bracket & Hardware.

18

PART #

Trolley and Monorail Support Bracket

P2751

MONORAIL, TROLLE Swivel Frame Trolley with Eyebolt, 1 Foot Chain and Snap-hook.

P501

MONOMOUNT, MONORAIL SUPPORT Support Bracket; Fits 3, 4, 6 & 8, Standard


Pipe Flanges, Includes P1354 Hinge, (4) P3010 Nuts and P371 Bolts.

PART #

Flange

PF-3CS

Flange, 3 150 lb. FF, 2.67 Bored, Stainless Steel,


with Threaded Coupling.

PF-4CS

Flange, 4 150 lb. FF, 2.67 Threaded, Stainless Steel,


with Threaded Coupling.

PF-6CLS

Flange, 6 150 lb. FF, 2.67 Bored, Stainless Steel with Cam-lock Connector.

12

See Accessories Section for Different Configurations.


Link to Flanges

60

ISOKINETIC SOURCE SAMPLING EQUIPMENT


x -522 So r
C-572 So r
26

M-CBR5A-M

27

M-CBR3A-M

Magnetic Type
Circuit Breaker
Rocker Switch

20

o
o
19

M-S 31

XC-10U

(E
(M
1

Rugged Custom
Molded X-Case

Digital Filter and


Probe Temperature
Controllers

o
o

h)
r )

TC-765KF

Temperature
Display

17

QC-MAN-F3

18

QC-MAN-M2

Manometer Quick
Connects

-522

16

Dual
Column
Manometer

M-RA911

Rocker Switches

12

MC-T

14

15

Vacuum Gauge

28

M-31302A

7-Channel
Temperature
Selector Switch
TC-PJK

GM-110

XC-522 Dry English Gas Meter


GM-AP25

XC-572 Dry Metric Gas Meter

25

24

Stainless Steel Male


Non-Reversible Pump
Quick Connect

23

10

Electric
Receptacle

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

22

Standard Stainless
Steel Female Pump
Connection (Pressure)

M-422 S

Manometer Zero
Adjust Knobs

(Vaccum)

M-49BK

L-441160

Heavy Duty
Panel Latches

11

QC-B F6-SS

3439T12

Strap

Color Coded
Thermocouple Jacks
QC-B M6-SS

B2V -6S

Coarse
Control Valve

Elapsed Timer
G301U

M-42210

M-SCKT15A

Power Connect
Inlet

21

AM-MCP

QC-B F8-SS

QC-B F4-SS

Standard Stainless Steel


Sample Quick Connect

Standard Stainless
Steel Pitot Quick
Connects

Umbilical
Cable Power
Connection

13

Description

TC-765KF
M-SD31
MC-T
M-SCKT15A
M-49BK
M-31302A
TC-PJK
QC-BHF8-SS
QC-BHF4-SS
QC-BHF6-SS
QC-BHM6-SS
B2VH-6S
NV3HA-6S
DGM-110
G301U
M-42210
QC-MAN-F3

Display, TC, PNI, LED, 120/220V


Controller, Temp, Red LED, Watlow
Timer, MC, Veeder-Root
Conn, Pwr, IEC Inlet 15A/250V
Recept, EL, Snap-In, Term
Switch, TC. 7 Channel
TC Jack, Type K, PNL, Snap-In
QC, Blkhd, 1/2IN-1/2TU, F, SS
QC, Blkhd, 1/4IN-1/4TU, F, SS
QC, Blkhd, 3/8IN-3/8TU, F, SS
QC, Blkhd, 3/8IN-3/8TU, M, SS
Valve, Ball, 3/8TU, SS, PNL, Nut
Valve, Needle, Angle, 3/8T-3/8T, S
Meter, Dry Gas, 110 Rockwell
Gage, Vac, 0-30HG, 1.5IN, PNL
Manometer, Dual, PNL, 0-10 H2
QC-Manometer, F-1/8MNPT, S

Part Number

18
19
20
21

Manometer Level
Adjust

NV3 A-6S

Fine Control
Valve

XC-522 and XC-572 Components List

Part Number

M-422B

Call for information on


110V / 240V Models.

Description

QC-MAN-M2
XC-10U
M-RA911
AM-MCP

QC-Manometer, M-1/4HB, Delrin


Black RotoRack Shallow Case
Switch, Curvette, EC Comp., I-O
Replacement Meter Console
Wired Amphenol Sub-Assembly
22 M-422B
Bracket, Manometer, Adjust,
Stainless Steel
23 M-422DS
Manometer Displacer Knob
24 L-441160
Latch, Panel, Screw, Large, Sou
25 3439T12
Webbing, 2, Black Nylon
26 M-CBR5A-M Magnetic Type Circuit Breaker
Rocker Switch, 5 Amp., 120V
27 M-CBR3A-M Magnetic Type Circuit Breaker
Rocker Switch, 3 Amp., 240V

XC-572 (Metric)
28 DGM-AP25

Meter, Dry Gas, AP25 W/Union

61

ISOKINETIC SOURCE SAMPLING EQUIPMENT


C

F C
Conversion Factors

To Convert From

ultiply By

rea
Square Feet (ft2)

Square Centimeters (cm2)

929.0304

Square Feet (ft )

Square Meter (m )

0.09290304

Square Feet (ft2)

Square Inches (in2)

Square Inches (in )

144

Square Centimeters (cm )

6.4516

Feet (ft....)

Centimeters (cm)

30.48

Feet (ft....)

Meters (m)

0.3048

Feet (ft....)

Inches (in)

12

Inches (in)

Millimeters (mm)

25.4

Inches (in)

Centimeters (cm)

2.54

Pounds (lb)

Grains (gr)

7000

Pounds (lb)

Grams (g)

453.59237

Grains (gr)

Grams (g)

0.06479891

Kilograms (kg)

Pounds (lb)

2.2046226

Kilogram-force (kgf)

Newton (N)

9.80665

Pound-Force9 (lbf)

Newton (N)

4.44822

Degrees Celsius (C)

Kelvin (K)

K = C + 273.15

Degrees Celsius (C)

Degrees Fahrenheit (F)

F = 9/5 (C + 32)

Degrees Fahrenheit (F)

Degrees Rankine (R)

R = F + 459.67 = 1.8k

Degrees Fahrenheit (F)

Degrees Celsius (C)

C = 5/9 (F -32)

British Thermal Unit per Min. (Btu/min.)

Steam, Pounds per Hour (lb/hr Steam)

1 X 103

Horsepower (hp)

Watts (W)

745.7

Horsepower, boiler (hp)

British Thermal Unit Per Hour (Btu/hr)

33445.7

Horsepower, boiler (hp)

Kilowatts (kW)

9.8095

Kilowatts, Hours (kWhr)

British Thermal Unit Per Hour (Btu/hr)

3414.43

British Thermal Unit, mean (Btu)

Kilogram-Calories (kcal)

0.252

British Thermal Unit, mean (Btu)

Watts per Second, Joule (J)

1055.06

Millimeters of Mercury (mm Hg)

25.4

Length

Mass/Force

emperature

Power, Energy,

eat

Pressure
Inches of Mercury (in Hg)
Inches of Mercury (in Hg)

Inches of Water (in H20)

13.6

Inches of Mercury (in Hg)

Atmospheres (atm)

0.0334211

Inches of Mercury (in Hg)

Kilopascals (kPa)

3.386388

Atmospheres (atm)

Bars (bar)

1.01325

Atmospheres (atm)

Pounds per Square Inch (psi)

Pascals (Pa)

Newton per Square Meter (N/m )

1.0

Cubic Meters (m3)

Cubic Feet (ft3)

35.314667

Cubic Feet (ft )

Liters (l)

28.136847

Liters (l)

Cubic Centimeters (ccm)

1000

14.695949
2

Volume
3

62

ISOKINETIC SOURCE SAMPLING EQUIPMENT

63

ISOKINETIC SOURCE SAMPLING EQUIPMENT


C
Avogadros Number
Gas Constants

6.02 x 1023 atoms/g atom


82.05 atm cm3/(g-mole * K)
1.987 cal/(g-mole * K)
10.731 ft.... lb in2/(lb-mole * oR)
0.732 ft3 atm/(lb-mole * oR)
1 g-mole of Ideal Gas 24.05 Liters at US EPA Standard Conditions

C
Standard Temperature (Tstd)
Standard Pressure (Pstd)

20oC (68oF)
760mm Hg (29.92in Hg)

C
Parts-per-million by volume (ppmv) to milligrams per dry standard cubic meter (mg/dscm)

Correct to x% O2

20 .9 x%O 2
C s @ x % O2 = C s

20 .9 %O 2 ( dryactual )

Gas Concentration Unit

64

To Convert From

To

Multiply By

Parts-per-million(ppm) SO2

Nanogram/Std Cubic Meter (ng/scm) SO2

2.66 x 106

Parts-per-million(ppm) SO2

Pounds/Std Cubic Foot (lb/scf) SO2

1.660 x 10-7

Parts-per-million(ppm) NOx

Nanogram/Std Cubic Meter (ng/scm) NOx

1.912 x 106

Parts-per-million(ppm) NOx

Pounds/Std Cubic Foot (lb/scf) NOx

1.194 x 10-7

ISOKINETIC SOURCE SAMPLING EQUIPMENT

C
An
As
Bws
Cp
Cp(std)
cs
De
Dn
p
(p1/2) avg
%EA
Fd
Fo
H@
H
%I
K
K
Kp
L
m
Md
Ms
pmr
Pb
Ps
Pstd
Qaw
Qsd
w

Ts
Tstd
Tamb
Vcr
Vm
Vlc
W

Sampling Nozzle Cross-Sectional Area, mm2 (in2)


Stack Cross-Sectional Area, m2 (ft2)
Percent Moisture in Stack Gas, % H2O
Pitot Tube Calibration Coefficient
Standard Pitot Tube Calibration Coefficient
Particulate Concentration in Stack Gas, g/dscm gr/dscm (lb/dscf gr/dscf)
Equivalent Diameter, m (ft....)
Sampling Nozzle Diameter, mm (in)
Stack Gas Velocity Pressure, mm H2O (in H2O)
Average of the Squareroots of Velocity Pressure, (mm H2O)1/2 (in H2O)1/2
Percent Excess Air, %
F factor for dry effluent, used with percent O2, dry basis
Fuel Factor
Pressure Drop across Orifice Meter for 21.2 lpm (0.75cfm) at Std Conditions, mm H20 (in H2O)
Pressure Drop across Orifice Meter, mm H20 (in H2O)
Isokinetic Sampling Rate, %
Isokinetic Rate Constant
Critical Orifice Calibration Factor
Pitot Tube Constant
Length of Duct Cross-Section at Sampling Site, m (ft....)
Mass, g (lb)
Stack Gas Dry Molecular Weight, g/g-mole (lb/lb-mole)
Stack Gas Wet Molecular Weight, g/g-mole (lb/lb-mole)
Pollutant Mass Emission Rate, kg/hr (lb/hr)
Barometric Pressure, mm Hg (in Hg)
Absolute Stack Pressure, mm Hg (in Hg)
Standard Pressure, 760 mm Hg (29.92 in Hg)
Actual Wet Volumetric Flowrate, acmm (acfm)
Dry Standard Volumetric Flowrate, dscmm (dscfm)
Density of Water, 0.9982 g/ml
Time (minutes)
Stack Temperature, oC (oF)
Standard Temperature, 293K (528oR)
Ambient Temperature, oC (oF)
Critical Orifice Volume, m3 (ft3)
Dry Gas Meter Volume, m3 (ft3)
Volume or Mass Liquid Collected in Impingers, ml or g
Width of Duct Cross-Section at Sampling Site, m (ft....)
Dry Gas Meter Calibration Factor

65

ISOKINETIC SOURCE SAMPLING EQUIPMENT


e eren e

ethods

MERCURY SAMPLING EQUIPMENT


A

h d 30B

S
A

AU IT (RATA)

ISOKINETIC SAMPLING EQUIPMENT


M
M

h d1

h d2

h d3

h d4

h d5

h d 5B

dd

h d 6B

h d 11

A d PM

h d8

h d 12

h d 13A

h d 13B

h d 17

P
F

h d 23

h d 26A

h d 29

h d 201A

PM10 E

h d 202

C
M

h d 202

C
M

h d 206

h d 306

A dM
L

& SO2

d (SZL)
(SIE)

I -

S
R

h d 15A

T
P
P

R d

h d 16A

R d

h d 18

h d 26

h d 106

h d 308

h d 0030

V
C

O
d (VOST)

h d 0031

V
(SMVOC

h d 0040

P
C
T d

&

h d 0051

dS

dS
dB
C

d
dB
Ch

S
d

(PO C )

d
d Ch

C
VOST)

d
d

Ch

&F
&

GAS ANALYSIS EQUIPMENT

h d3

M
MET O

3B

P
M

Ch

E
O

d h d
dW

dA

h d 316

F
W
d

h d 0010

S
C

h d 0011

F
d h d ,O h
A d h d
dK

h d 0061

h d7

h d 6C
S
F

FLOW, PRESSURE & TEMPERATURE


dV
S-P

(T

GAS SAMPLING EQUIPMENT

h d 4A

S
(A

h d6

h d 6A

.M

h d)

A dM
dC

& SO2

d ,M
d

G
F

h d 7E

h d 10

h d 25A

O
d
E
S

dC

h d 6C

Ch

V
R

S
M

ETERMINATION OF NITROGEN
OXI E EMISSIONS FROM
STATIONARY SOURCES

GAS ANALYSIS FOR T E


ETERMINATION OF EMISSION
RATE CORRECTION
FACTOR OR EXCESS AIR

h d 3A

G
d

IRM E

66

h d2

P
F

d
d

S
C

d E

S
S

d E

O d
S

M
S

d E

G
C
F

O
I

N
F
C

S
T
A

ISOKINETIC SOURCE SAMPLING EQUIPMENT


Isokinetic
Alumina...........................................................54
Balances .........................................................55-56
Ball & Socket Joint Adapters ...........................29-30
Ball & Socket Joint Adapters, Impingers..........29-30
Calibration Equipment & Services ..................59
Cases, Equipment...........................................19
Cases, Impinger..............................................21
Cases, Risers..................................................21
Cases, Modular Sample Frame.......................21
Cases, Umbilical Gooseneck Adapter .............21
Cases, Impinger Inlet Strain Relief ..................21
Cases, Power Box Adapter .............................21
Consoles, XC-5000 Automated Sampling ......4-5
Consoles, XC-522 / XC-572 Manual ..............6-9
Consoles, XC-522 Accessories ......................8
Consoles, XC-572 Accessories ......................9
Consoles, XC-563 Digital Source Sampling...43
Consoles, XC-522 Accessories ......................8
Consoles, XC-563 Digital Source Sampling...10
Consoles, XC-563 Audit Kit ............................10
Consoles, Method 4 Source Sampling 11
Dessicator & Desiccants .................................53
Dessicator & Desiccants, Vacuum Pump ........53
Drierite Desiccants ..........................................54
Filter Media .....................................................49-50
Filter Ovens, Heated .......................................20
Filter Ovens, Strain Reliefs..............................20
Filter Ovens, Socket Adapter...........................20
Filter Media, In-Stack Thimbles .......................50
Glassware, Sets..............................................22
Glassware, Method 5 Sets ..............................22
Glassware, Deluxe Method 5 Sets ..................23
Glassware, Accessories ..................................23
Glassware, Filter Assemblies/Components .....24
Glassware, Individual & Accessories ...............25
Glassware, Impinger Accessories ...................25
Glassware, Cyclones ......................................25
Glassware, Connectors...................................26
Glassware, Controlled Condensate.................26
Glassware, Condensers..................................27
Glassware, Adapters .......................................27
Glassware, Method 17 ....................................27
Glassware, Method 202 ..................................28
Glassware, Method 23 ....................................28

Meter Calibration.............................................57
Meter Calibration Equipment...........................57
Method 4.........................................................33
Method 4, Accessories ....................................33
Method 5, Basic ..............................................34
Method 5, Deluxe-Plus....................................34
Method 5, Compact.........................................35
Method 5, Heated Filter Assembly...................35
Method 5, 5G ..................................................36
Method 5, 5I....................................................36
Method 5, Alternate 5I .....................................36
Method 8.........................................................37
Method 8, Accessories ....................................37
Method 8, Alternate CTM-13 ...........................37
Method 17, Flexible & Rigid.............................38
Method 17, In-Stack Filter Assemblies ............39
Method 17, Integrated In-Stack
Filter Assemblies.............................................39
Method 17, Glass In-Stack
Filter Assemblies.............................................39
Method 23, Deluxe Plus ..................................40
Method 23, Sampler Kit Components..............40
Method 23, Coolant Pump Options .................40
Method 23, Glassware ....................................40
Method 23, Individual Accessories ..................40
Method 26A, HCI ............................................41
Method 26A, Accessories................................41
Method 29, Multiple Metals .............................42
Method 29, Accessories ..................................42
Monorails ........................................................60
Method 201A, Particle Sizing ..........................44
Method 201A, PM2.5 Cyclone Set ..................44
Method 201A, Expanded Nozzle Set...............44
Method 201A, PM10 Cyclone Set ...................45
Method 201A, PM10 & PM2.5 Cyclone Set.....45
Method 201A, Cascade Impactor Set..............46
Method 201A, Particle Sizing Data Reduction
WINCIDRS Software ......................................46
Method 202, Dry Impinger...............................47
Method 202, Sampling Accessories ................48
Method 202, Purge Accessories......................48
Method 0061, Hexavalent Chromium ..............48
Nozzle Calibration ...........................................59
Nozzles, Isokinetic Sampling..........................14

Nozzles, Sets..................................................14
Nozzles, Oversized.........................................14
Nozzles, Unions..............................................15
Nozzles, Tube Nuts ........................................15
Nozzles, Rings................................................15
Nozzles, Vinyl Nozzle Caps............................15
Nozzles, Brushes............................................15
Nozzles, Brush Sets .......................................15
Nozzles, Ferrules............................................15
Nozzles, Small Parts Kit .................................15
Nozzles, Steel Alloys ......................................15
Ontario-Hydro/Mercury....................................43
Ontario-Hydro/Mercury Accessories................43
Orifice Set .......................................................58
Pitot Audit Equipment & Manometers..............59
Probe Assemblies, Method 5..........................16
Probe Assemblies, Packing Gland .................16
Probe, Method 5 Tube Heaters .......................16
Probe, Replacement Pitot Tips.......................16
Probe Liners ...................................................17
Probe Liners, Tubing ......................................17
Probe Liners, Adapters...................................17
Probe Sheaths, Method 5 Inconel ..................18
Probe Sheaths, Method 5 Stainless Steel .......18
Probe Sheaths, Air Cooled Method 5 ..............18
Probe Sheaths, Alloy Method 5 .......................18
Probe Sheaths, Blowers..................................18
Pump Assemblies, Method 5..........................12
Pump Frame, Optional XF-05HW...................12
Pumps, Lubricated Rotary Vane.....................12
Pumps, Lubricated Rotary Vane.....................12
Pumps, Diaphragm.........................................13
Sample Lines, Heated.....................................32
Sample Lines, Unheated Jumpers ..................32
Sample Lines, Strain Relief .............................32
Sample Recovery............................................51
Sample Recovery, Accessories .......................52
Sample Recovery, Bottles ...............................52
Silica Gel.........................................................54
Umbilical Cables, Split Back............................31
Umbilical Cables, Classic ................................31
Umbilical Cables, Classic Adapters .................31
Umbilical Cables, Accessories.........................31
Wet Test Meters ..............................................58

67

TERMS AN

CON ITIONS

PRICES AN TERMS
Our prices are subject to change without notice. The
price in effect when we receive your order will apply.
All prices are Ex Works Holly Springs, North Carolina.
We will be pleased to furnish quotations by phone, fax
or e-mail. Terms of payment are Net 30 days with
established credit, or by Visa/MasterCard/American
Express at time of order. Invoices over 30 days past
due are subject to 1.5% per month finance charge.
CONFIRMING OR ERS
Please make sure that all confirming orders are clearly
marked to avoid duplicate orders.

APE INST UMENTS, INC.


Solutions for Source Sampling Equipment
Apex Instruments is a world leader in the manufacture, design and
distribution of source sampling equipment. Our products are used
in a wide variety of sampling scenarios. Our equipment complies
with emissions measurement standards for stationary combustion
sources in accordance with US EPA guidelines. We are located
approximately 20 miles from the United States Environmental
Protection Agency in Research Triangle Park, N.C. Our goal is to
provide you with the proper, well engineered equipment in order
for your job to run smoothly and have consistent, accurate and
reliable results.
C
C
VC
Apex Instruments understands the needs and high demands of the
individuals working in the source sampling industry. The primary end
users of our equipment consist of government agencies, consulting
firms and private industries throughout North America and in 50
countries around the globe. Our knowledgeable staff includes many
skilled industry professionals, stack testers and chemists. They all
will help you make important decisions regarding your specific application needs.
C
B
VC
Apex Instruments offers dedicated, climate controlled, precision
calibration services for a variety of measuring instruments. This
includes gas meters, orifices and pitot tubes to help keep all your
calibration equipment up-to-date. Our trained staff will utilize the
reliable calibration equipment and tools such as NIST Certified Bell
Prover, wet test meters, electronic flow calibrators and wind tunnels.
We offer a certification of calibration when requested.
C
F B C
B Y
Apex Instruments custom-designed facility was built in 2005.
The warehouse layout provides a smooth flow for the assembly
and fabrication departments. We can design, build and expedite
all equipment orders quickly through our in-house engineering,
production and welding departments. Apex continues with their
steady commitment to quality in compliance testing, by consistently
designing and developing reliable source sampling equipment. We
follow guidelines set by U.S. EPA Reference Methods and always
keeping the genuine needs of the stack samplers in mind.
W
Apex Instruments recently received the (SHARP) Safety and Health
Achievement Award from the NC (DOL) Department of Labor. This
program recognizes small to medium size businesses that establish
and maintain effective safety standards and health programs. We
were also ranked in the top 500 by Inc. Magazine as being one of
the fastest growing privately held companies.

S IPMENTS AN
ELIVERY
Unless otherwise instructed, shipments are made as
soon as possible after receipt of order by method of
transportation which in our judgement will be most
satisfactory. Freight charges are prepaid and added
to the invoice. The right is reserved to make partial
shipments where delays beyond our control may
delay a portion of the order.
EXPORT PROCESSING AN PRICING
Prices do not include customs and duty charges, freight,
insurance, export fees, bank wire transaction fees or any
additional handling fees.
RETURNE ITEMS
Authorization must be obtained from us before returning
any goods. When requesting return authorization, please
advise reason for return, date of purchase, your P.O.
number and our invoice number. Equipment produced to
special specifications are not returnable. All returns must
be shipped freight prepaid at the purchasers expense and
are subject to a restocking fee.
LIMITE WARRANTY
APEX INSTRUMENTS, INC. warrants products to be
free from defects in workmanship for a period of one
year from date of delivery. The sole and exclusive remedy
for defective goods shall be to repair or replace defective
parts or payment price of the goods for which damages are
claimed at APEX INSTRUMENTS, INC.s option. Freight
for return of defective items will be at the sole discretion
of APEX INSTRUMENTS, INC. Except as described in
our guarantee, there are no express warranties or implied
warranties including, but not limited to, merchantability and
fitness for a particular purpose. APEX INSTRUMENTS,
INC. shall not be subject to and disclaims: (1) any other
obligations or liabilities arising out of breach of contract or
warranty, (2) any obligations whatsoever arising from tort
claims (including negligence and strict liability) or arising
under other theories of law with respect to products sold
or services rendered by APEX INSTRUMENTS, INC.,
or any undertakings, acts or omissions relating thereto,
and (3) all consequential, incidental and contingent
damages whatsoever.
ESIGN C ANGES
Design changes are made from time to time. Some items
may differ slightly from catalog illustrations or descriptions.
Changes are made in the interest of better performance
and quicker delivery.
ACCEPTANCE OF TERMS AN CON ITIONS
APEX INSTRUMENTS, INC. sells products only under
foregoing terms and conditions and will not be bound
to terms and conditions stated by any purchaser in any
offer, acceptance or other contractual document. Placing
an order or accepting delivery of products constitutes
acceptance of terms and conditions.
Great care has been taken in preparation of this literature,
however, we cannot be responsible for any omissions or
typographical errors.

XC-522

XC-5000

XC-40

Av. Juan Bautista Alberdi 5283 1P


Ciudad Autnoma de Buenos Aires
Tel: +54 11 4684 2232
http://www.siafa.com.ar
ventas@siafa.com.ar

Isok net c
qu pment
atalog

Publication: PEC-Isokinetic
Date Issued: 1-01-12

You might also like