You are on page 1of 3

ALKcar Aliexpress Store No.

324381

ALKcar BDM100 v1255 ecu programmer BDM100 Programmer V1255 programmer

BDM100 Programmer V1255 is ALKcar universal programmer. BDM 100 programmer requires
the ECU to be open. BDM100 v1255 ecu programmer can create perfect copies of the whole
software of an ECU.

BDM100 Programmer V1255 BDM100 v1255 ecu programmer


BDM100 Programmer V1255 summary
1. BDM100 Programmer V1255 is a universal reader/programmer (it does not require our RACE
software necessarily) that allows the user to read and program files in the ECU supplied with
MOTOROLA MPC5xx processor (essential).
2. BDM100 v1255 requires the ECU to be open, "on the bench", as the reading/programming

ALKcar Aliexpress Store No.324381

operations are realized by linking a flat cable to specific area the ECU (the tool, on the other side,
is linked to the USB port of a computer).
3. BDM 100 allows also to create perfect copies of the whole software of an ECU (after having
read the original ECU software).
4. BDM100 v1255 ecu programmer software allows to read and program the WHOLE ECU
content of:
29BL802 SSOP eprom file (or ROM memory with maps if eprom physically not present);
MOTOROLA MPC5xx Processor file;
Serial Eprom content.
Please note that even in the case of the ECU blocking, due to the wrong checksum recalculation,
the ECU can always be reprogrammed and then retrieved (if the original software has been
previously stored).
BDM100 v1255 Description:
The BDM100 is a universal reader/programmer (it does not require our RACE software
necessarily) that allows the user to read and program files in the ECU supplied with MOTOROLA
MPC5xx processor (essential).
The ECU must be removed from the car and is programmed by special spring contacts without
soldering on the circuit board. This method is used for example if a car has no connection from the
OBD connector to the ECU or for very new ECU versions. The best tool for this is the BDM 100.
Which way of programming is used, depends on manufacturer, model, year and the ECU type in
the car.
Generally we use the easiest way of programming. So if a car can be programmed by the OBD
port, we will do it this way.
After the security entries for the OBD2 programming get more and more difficult, a new
possibility has come up for chip tuning of ECUs with Motorola MPC555 - 565.
This generation of Motorola processors contains 448KB - 1MB Flash memory. That memory
cannot be read and programmed with an eprom programmer. Therefore it is possible over the so
called BDM interface, which must be implemented on every ECU board. For that purpose there
are mostly 10 solder pads on the PCB.
Alternative there are ECUs with 12 or 14 solder pads, which can be supplied with operating
voltage over these pads.
The BDM100 connects these solder pads of the BDM port with the WinOLS PC over the USB

ALKcar Aliexpress Store No.324381

bus. The BDM100 gets its operating voltage from the USB bus. The ECU needs its own supply
voltage of +12 volts.
The BDM100 requires the ECU to be open, "on the bench", as the reading/programming
operations are realized by linking a flat cable to specific area the ECU (the tool, on the other side,
is linked to the USB port of a computer).
BDM100 also allows to create perfect copies of the whole software of an ECU (after having read
the original ECU software).
The software allows and program the Whole ECU content of:
1.29BL802 SSOP eprom file (or ROM memory with maps if eprom physically not present);
2.MOTOROLA MPC5XX Processor File;
3.Serial Eeprom content.
Please note that even in the case of the ECU blocking, due to the wrong checksum recalculation,
the ECU can always be reprogrammed and then retrieved (if the original software has been
previously stored).

You might also like