You are on page 1of 88

GRUNDFOS DATA BOOKLET

CR, CRI, CRN


Vertical multistage centrifugal pumps

60 Hz

CR, CRI, CRN

Table of contents

1.

Product introduction

Features and benefits


Terminal box positions
Viscosity
Ambient temperature and altitude

3
4
4
4

2.

Applications

3.

Performance range

4.

Product range

Identification

Type key
Codes

9
9

5.

6.

7.

8.

9.

Construction

10

CR 1s, 1, 3, 5, 10, 15 and 20


CRI, CRN 1s, 1, 3, 5, 10, 15 and 20
CR 32, 45, 64 and 90
CRN 32, 45, 64 and 90
CR 120 and 150
CRN 120 and 150

10
10
11
11
12
12

Operating conditions

13

Pumped liquids
Working and inlet pressure
Operating range of the shaft seal
Maximum inlet pressure

13
16
17
18

Selection and sizing

19

Selection of pumps
How to read the curve charts
Guidelines to performance curves

19
23
23

Performance curves

24

CR, CRI, CRN 1s


CR, CRI, CRN 1
CR, CRI, CRN 3
CR, CRI, CRN 5
CR, CRI, CRN 10
CR, CRI, CRN 15
CR, CRI, CRN 20
CR, CRN 32
CR, CRN 45
CR, CRN 64
CR, CRN 90
CR, CRN 120
CR, CRN 150

24
25
26
27
28
29
30
31
32
33
34
35
36

10. Technical data


CR 1s
CRI 1s
CRN 1s
CR 1
CRI 1
CRN 1
CR 3
CRI 3
CRN 3
CR 5
CRI 5
CRN 5
CR 10
CRI 10
CRN 10
CR 15
CRI 15
CRN 15
CR 20
CRI 20
CRN 20
CR 32
CRN 32
CR 45
CRN 45
CR 64
CRN 64
CR 90
CRN 90
CR 120
CRN 120
CR 150
CRN 150

37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69

11. Motor data

70

12. Accessories

72

Pipework connections
CR flange guide

13. Variants
Lists of variants - on request
Motors
Connections and other variants
Shaft seals
Pumps

72
76

77
77
77
77
77
77

14. Submittal data

79

15. Quotation text

81

16. Further product information

83

WebCAPS
WinCAPS
Grundfos GO

37

83
84
85

CR, CRI, CRN

Pump

This data booklet deals with Grundfos CR, CRI and


CRN pumps.

The CR pump is a non-self-priming, vertical multistage


centrifugal pump. The pumps are available with a
Grundfos standard motor.
The pump consists of a base and a pump head. The
chamber stack and the outer sleeve are secured
between the pump head and the base by means of
staybolts. The base has suction and discharge ports
on the same level (in-line).
All pumps are equipped with a maintenance-free
mechanical shaft seal of the cartridge type.
TM02 7698 3803

Fig. 1

Product introduction

1. Product introduction

Motor

CR, CRI and CRN pumps

Coupling

Features and benefits


Shaft seal
(Cartridge type)

Pump head

Outer sleeve
Impellers
Staybolts
Base
Base plate

Fig. 2

GR5357 - GR3395

Grundfos CR, CRI, CRN pumps are vertical multistage


centrifugal pumps. The in-line design enables the
pump to be installed in a horizontal one-pipe system
where the suction and discharge ports are in the same
horizontal plane and have the same pipe dimensions.
This design provides a more compact pump design
and pipework.
Grundfos CR pumps come with various pump sizes
and various numbers of stages to provide the flow and
the pressure required.
CR pumps are suitable for a variety of applications
from pumping of potable water to pumping of
chemicals. The pumps are therefore used in a wide
variety of pumping systems where the performance
and material of the pump meet specific demands.
The CR pumps consist of two main components: the
motor and the pump unit. The motor on a CR pump is a
heavy-duty Grundfos specified motor.
The pump unit consists of optimized hydraulics,
various types of connections, an outer sleeve, a top
and various other parts.
CR pumps are available in various material versions
according to the pumped liquid.

CR pump

CR pump with ANSI/NSF 61 listing is available. See


UL file MH26400 or contact Grundfos.

Motor
Grundfos standard motors - ML and Baldor
motors
CR, CRI and CRN pumps are fitted with a Grundfos
specified motor. The motors are all heavy-duty 2-pole,
NEMA C-face motors.

CR, CRI, CRN

Viscosity

Mounting designation

NEMA

Insulation class

F&B

Energy efficient
Premium efficiency - on request for 15 Hp
and above
TEFC - Totally Enclosed Fan Cooled
Enclosure class
(Grundfos standard)
ODP - Open Drip Proof - on request
1 x 115/208-230 V
60 Hz standard voltages 3 x 208-230/460 V
3 x 575 V
The motors are rated for:
Efficiency class*

Baldor
Approvals

ML

RU

RUUS

* 1-10 Hp ML motors are premium efficiency as standard.

Optional motors
The Grundfos standard range of motors covers a wide
variety of application demands. However, for special
applications or operating conditions, custom-built
motor solutions can be provided.
For special applications or operating conditions,
Grundfos offers custom-built motors such as:
explosion proof motors
motors with anti-condensation heating unit
low-noise motors
premium efficiency motors
motors with thermal protection.

The pumping of liquids with densities or kinematic


viscosities higher than those of water will cause a
considerable pressure drop, a drop in the hydraulic
performance and a rise in the power consumption.
In such situations, the pump should be fitted with a
larger motor. If in doubt, contact Grundfos.

Ambient temperature and altitude


If the ambient temperature exceeds the maximum
temperature limits of the pump or the pump is installed
at an altitude exceeding the altitude values in the chart
below, the motor must not be fully loaded due to the
risk of overheating.
Overheating may result from excessive ambient
temperatures or the low density and consequently low
cooling effect of the air at high altitudes. In such cases,
it may be necessary to use a motor with a higher rated
output (P2).
P2
[%]

100
90

80
70
60
50
60

80

100

120

140

160

Motor protection
3280

Single-phase Grundfos specified motors up to 7.5 Hp


have a built-in thermal overload switch.

Fig. 4

Three-phase motors must be connected to a motor


starter in accordance with local regulations.

Pos.

Fig. 3

Stellung 1212
Position

Terminal box positions

Stellung 3
Position
3

TM02 18 05 2001

As standard the terminal box is mounted on the suction


side of the pump.

Stellung 9 9
Position

7382

11483

15584

ft

Relationship between motor output (P2) and


ambient temperature/altitude

Legend

Terminal box positions

Stellung 6
Position
6
Standard

180
T [F]

TM03 4272 2006

Product introduction

Electrical data

Description

NEMA energy efficient motors

NEMA premium-efficiency motors

Example: From fig. 4 it appears that P2 must be


reduced to 88 % when a pump with a NEMA premiumefficiency ML motor is installed 15,584 ft (4750 m)
above sea level. At an ambient temperature of 167 F
(75 C), P2 of a standard-efficiency motor must be
reduced to 74 % of rated output.
In cases where both the maximum temperature and
the maximum altitude are exceeded, the derating
factors must be multiplied. Example: 0.89 x 0.89 =
0.79.

CR, CRI, CRN

Application

CR, CRI

CRN

Applications

2. Applications
Water supply
Filtration and transfer at waterworks
Distribution from waterworks
Pressure boosting in mains
Pressure boosting in high-rise buildings, hotels, etc.
Pressure boosting for industrial water supply
Industry
Pressure boosting in...
process water systems
washing and cleaning systems
vehicle washing tunnels
fire fighting systems
Liquid transfer in...
cooling and air-conditioning systems (refrigerants)
boiler feed and condensate systems
machine tools (cooling lubricants)
aquafarming
Transfer of...
oils and alcohols
acids and alkalis
glycol and coolants

Water treatment
Ultra-filtration systems
Reverse osmosis systems
Softening, ion exchange, demineralizing systems
Distillation systems
Separators
Swimming pools

Irrigation
Field irrigation (flooding)
Sprinkler irrigation
Drip-feed irrigation

Recommended version.
Alternative version.
CRT, CRTE version available. For further information about CRT, CRTE pumps, see Pumped liquids on page 13 or related CRT, CRTE product
guide.

CR, CRI, CRN

Performance range

3. Performance range
H
[m]

H
[ft]

300

1000
800

200

CR 120
CRN 120

60 Hz
CR 150
CRN 150

600
400

100
80

300

60
50
40

200

30

100
80

20

CR 1
CRI 1
CRN 1

CR 5
CRI 5
CRN 5

CR 1s
CRI 1s
CRN 1s

CR 15
CRI 15
CRN 15

CR 3
CRI 3
CRN 3

CR 10
CRI 10
CRN 10

CR 32
CRN 32
CR 20
CRI 20
CRN 20

CR 64
CRN 64
CR 45
CRN 45

CR 90
CRN 90

60
40

10

30
20
1

8 10

20

40

60

80 100

200

400

600 800

Q [US GPM]
1

5 6 7 8 10

20

30

40 50 60

80 100

Eff
[%]

Q [m/h]

80
60

20
0
1

8 10

20

40

60

80 100

200

400

600 800

Q [US GPM]

TM02 5518 0209

40

CR, CRI, CRN

Range
Nominal flow rate [US gpm]
Temperature range [F]
Temperature range [F]
- on request
Max. working pressure [psi]
Max. working pressure [psi]
- on request
Max. pump efficiency [%]

CR 1s

CR 1

CR 3

CR 5

CR 10

CR 15

CR 20

4.5

8.5

15

30
-4 to +250

55

95

110

362

362

362

362

362

362

362

Product range

4. Product range

-40 to +356

725

725

725

725

725

725

35

49

59

67

70

72

72

0.5 - 5.7
760
.33 - 2

1 - 12.8
790
.33 - 3

1.5 - 23.8
790
.33 - 5

3-45
780
.75 - 7.5

5.5 - 70
820
.75 - 15

9.5 - 125
800
2-25

11-155
700
3-25

CR pumps
CR: Flow range [US gpm]
CR: Max. pump pressure (H [ft])
CR: Motor power [Hp]
Version
CR:
Cast iron and stainless steel AISI 304
CRI:
Stainless steel AISI 304
CRN:
Stainless steel AISI 316
CRT, CRTE:
Titanium

See CRT, CRTE product guide

CR pipe connection
Oval flange (NPT)
Oval flange (NPT) - on request
ANSI flange size
ANSI flange size - on request
ANSI flange class

1"
1.25"
1.25"
250 lb.

1"
1.25"
1.25"
250 lb.

1"
1.25"
1.25"
250 lb.

1.25"
1"
1.25"
250 lb.

2"
1.5"
2"
250 lb.

2"
2"
250 lb.

2"
2"
250 lb.

1"
1.25"
1.25"
300 lb.
1",
1.25"
2"

1"
1.25"
1.25"
300 lb.
1",
1.25"
2"

1"
1.25"
1.25"
300 lb.
1",
1.25"
2"

1.25"
1"
1.25"
300 lb.
1",
1.25"
2"

2"
1.5"
2"
300 lb.
1.5",
2"
-

2"
2"
300 lb.
1.5",
2"
-

2"
2"
300 lb.
1.5"
2"
-

1.25"
1.25"
300 lb.
1",
1.25"
2"

1.25"
1.25"
300 lb.
1",
1.25"
2"

1.25"
1.25"
300 lb.
1",
1.25"
2"

1.25"
1.25"
300 lb.
1",
1.25"
2"

2"
2"
300 lb.
1.5",
2"
-

2"
2"
300 lb.
1.5",
2"
-

2"
2"
300 lb.
1.5",
2"
-

1.25"
-

1.25"
-

1.25"
-

2"
2"

2"
2"

CRI pipe connection


Oval flange (NPT)
Oval flange (NPT) - on request
ANSI flange size
ANSI flange class
Clamp coupling (NPT) - on request
Union (NPT ext. Thread) - on request
CRN pipe connection
PJE (Victaulic)
PJE (Victaulic) - on request
ANSI flange size
ANSI flange size - on request
ANSI flange class
Clamp coupling (NPT) - on request
Union (NPT ext. Thread) - on request
CRT pipe connection
PJE coupling (Vitaulic)
ANSI flange size - on request

Available.
See section 7. Operating conditions on page 13 for specific working pressures.

CR, CRI, CRN

Product range

Range
Nominal flow rate [US gpm]

CR 32

CR 45

CR 64

CR 90

CR 120

CR 150

140

220

340

440

610

750

-22 to +2501)

Temperature range [F]


Temperature range [F]
- on request
Max. working pressure [psi]
Max. working pressure [psi]
- on request
Max. pump efficiency [%]

-22 to +2501) & 2)

-40 to +356

435

435

435

435

435

435

580

580

580

580

76

78

79

80

75

73

14-210
995
5-50

22-310
940
7.5-60

34-450
565
10-60

44-630
595
15-60

61-700
685
20-100

75-790
570
25-100

2.5"

3"

4"

4"

5" 3)

5" 3)

CR pumps
CR: Flow range [US gpm]
CR: Max. pump pressure (H [ft])
CR: Motor power [Hp]
Version
CR:
Cast iron and stainless steel AISI 304
CRI:
Stainless steel AISI 304
CRN:
Stainless steel AISI 316
CRT, CRTE:
Titanium
CR pipe connection
Oval flange (NPT)
Oval flange (NPT) - on request
ANSI flange size
ANSI flange size - on request
ANSI flange class

3"

4"

5" 3)

6"

125/
250 lb.

125/
250 lb.

5"
125/
250 lb.

6"

125/
250 lb.

125/
250 lb.

125/
250 lb.

3"
2.5"
3"
150/
300 lb.
-

4"
3"
150/
300 lb.
-

4"
4"
150/
300 lb.
-

4"
4"
5"
150/
300 lb.
-

4"
5"
6"
150/
300 lb.
-

4"
5"
6"
150/
300 lb.
-

3)

CRI pipe connection


Oval flange (NPT)
Oval flange (NPT) - on request
ANSI flange size
ANSI flange class
Clamp coupling (NPT) - on request
Union (NPT ext. Thread) - on request
CRN pipe connection
PJE (Victaulic)
PJE (Victaulic) - on request
ANSI flange size
ANSI flange size - on request
ANSI flange class
Clamp coupling (NPT) - on request
Union (NPT ext. Thread) - on request
CRT pipe connection
PJE coupling (Vitaulic)
ANSI flange size - on request

Available.
See section 7. Operating conditions on page 13 for specific working pressures.
1)
CRN 32 to CRN 90 with HQQE shaft seal: -40 F to +250 F.
2) CR, CRN 120 and 150 with 75 or 100 Hp motors with HBQE shaft seal: 0 F to +250 F.
3)
CR 5" flange is not manufactured to ANSI specification. Gasket contact surface is approximately 0.25". CR 6" ANSI flange adapter is manufactured
to ANSI B16.5 specification.

CR, CRI, CRN

Type key

Example

CR, CRI, CRN

Materials

Example

CR 32 (s) -4 -2 -A -G -G -E - HQQE

Type range:
CR, CRI, CRN

Basic version

Carbon-graphite filled PTFE (bearings)

A -G -A -E -H QQ E

Wetted parts AISI 316

Nominal flow rate [m /h]

GI

All parts stainless steel, wetted parts AISI 316

All impellers with reduced diameter


(applies only to CR, CRI, CRN 1s)

Wetted parts AISI 304

II

All parts stainless steel, wetted parts AISI 304

Number of impellers

Bronze (bearings)

Number of reduced diameter impellers


(CR, CRN 32, 45, 64, 90, 120, and 150)

SiC bearings + PTFE neck rings

Special version

Code for pump version

Code for rubber parts

Code for pipe connection


Code for materials

Code for rubber parts

FXM

Code for shaft seal

FFKM

FKM

Codes
Example
Pump version1)

Identification

5. Identification

EPDM

Shaft seal

A -G -A -E -H QQ E

O-ring seal with fixed driver

Rubber bellows seal

Cartridge seal with O-ring

Balanced cartridge seal with O-ring

Metal bellows cartridge seal

Double seal, back-to-back

Basic version

Oversize motor

Certificate/approval

CR pump for high temperatures


(air-cooled top assembly)

Horizontal version

Carbon, synthetic resin-impregnated

HS

High-pressure pump with high speed MLE


motor

Cemented tungsten carbide, embedded (hybrid)

Silicon carbide

Different pressure rating

Cemented tungsten carbide

Pump with different max speed

Other ceramics

Pump with low NPSH

EPDM

Magnetic drive

FXM

Fitted with sensor

FFKM

Undersize motor

FKM

Horizontal version with bearing bracket

SF

High pressure pump

Over size motor


(two flange sizes bigger)

Special version

Double seal, tandem

Special version

1)

If a pump incorporates more than two pump versions, the code for
the pump version is X.
X also indicates special pump versions not listed above.

Pipe connection
A

Oval flange Rp thread

Oval flange NPT thread

CA

FlexiClamp (CRI, CRN 1, 3, 5, 10, 15, 20)

CX

Triclamp (CRI, CRN 1, 3, 5, 10, 15, 20)

DIN flange

ANSI flange

JIS flange

Changed diameter of ports

PJE coupling

Special version

CR, CRI, CRN

Construction

6. Construction
CRI, CRN 1s, 1, 3, 5, 10, 15 and 20

Sectional drawing

TM02 1808 2001 - GR7373 - GR7375

TM02 1198 0601 - GR7377 - GR7379

CR 1s, 1, 3, 5, 10, 15 and 20

Sectional drawing

10

10

6
7

Pump head

Cast iron

Shaft

Stainless steel

4
5
6

Impeller
Chamber
Outer sleeve
O-ring for outer
sleeve
Base
Neck ring
Shaft seal
Bearing rings
Rubber parts
FGJ flange

Stainless steel
Stainless steel
Stainless steel

8
9
10

12

2)
3)
4)
5)
6)
7)

10

Materials

1)

Designation

8
9
12
11

Materials: CRI, CRN

Materials: CR
Pos.

TM03 2156 3805

TM02 1194 1403

AISI/ASTM

Pos.

Designation

Materials
iron3)

AISI/ASTM

A 48-30 B

Pump head

AISI 3161)
AISI 4312)
AISI 304
AISI 304
AISI 304

Pump head cover

Cast
Stainless steel

Shaft

Stainless steel

AISI 3165)
AISI 3296)
AISI 4317)

Base

Stainless steel

CF 8M 4)

Neck ring

PTFE

10

Shaft seal

Cartridge type

11

Base plate

Cast iron3)
Silicon carbide

EPDM or FKM
Cast iron
PTFE
Cartridge type
Silicon carbide
EPDM or FKM
Cast iron

CR 1s, 1, 3, 5
CR 10, 15, 20
Stainless steel available on request.
CF 8M is cast equivalent of AISI 316 stainless steel.
CRI/CRN 1s, 1, 3, 5
CRN 10, 15, 20
CRI 10, 15, 20

A 48-30 B

Bearing rings

A 48-30 B

A 48-30 B
CF 8M 4)

A 48-30 B

Rubber parts

EPDM or FKM

Impeller

CRI
Stainless steel

AISI 304

Chamber

Stainless steel

AISI 304

Outer sleeve

Stainless steel

AISI 304

O-ring for outer sleeve EPDM or FKM

12

FGJ flange ring


Oval flange

Ductile iron3)
Stainless steel

A 65-45-12
AISI 316

Impeller

CRN
Stainless steel

Chamber

Stainless steel

AISI 316

Outer sleeve

Stainless steel

AISI 316

O-ring for outer sleeve EPDM or FKM

12

FGJ flange ring

Ductile iron3)

AISI 316

A 65-45-12

CR, CRI, CRN

Construction

CRN 32, 45, 64 and 90

Sectional drawing

TM02 7399 3403

TM01 2150 1298

CR 32, 45, 64 and 90

TM06 0691 0714

TM01 1837 3713

Sectional drawing

Materials: CRN

Materials: CR
Pos. Designation

Materials

AISI/ASTM

Pos. Designation

Materials

AISI/ASTM

ASTM 80-55-06

Pump head

Stainless steel

CF 8M equal to
AISI 316

ASTM 25B

Motor stool

Cast iron
EN-GJL-200 1)

ASTM 25B

Stainless steel

AISI 431

Shaft

Stainless steel

Stainless steel

AISI 304

Impeller

Stainless steel

AISI 316

Stainless steel

AISI 304

Chamber

Stainless steel

AISI 316

Sleeve

Stainless steel

AISI 304

Sleeve

Stainless steel

AISI 316

O-ring for sleeve

EPDM or FKM

O-ring for sleeve EPDM or FKM

Base

Cast iron
EN-GJS-500-7

Base

Stainless steel

Neck ring

Carbon-graphite-filled
PTFE

Neck ring

Carbon-graphite-filled
PTFE

10

Shaft seal

11

Bearing ring

SiC/SiC

12

Base plate

Cast iron
EN-GJS-500-7 1)

Pump head

Cast iron
EN-GJS-500-7

Motor stool

Cast iron
EN-GJL-200

Shaft

Impeller

Chamber

6
7

10

Shaft seal

11

Bearing ring

SiC/SiC

12

Flange ring

Ductile iron

Rubber parts

EPDM or FKM

ASTM 80-55-06

A 65-45-12

1)

1)

Flange ring

Ductile iron

Rubber parts

EPDM or FKM

CF 8M equal to
AISI 316

ASTM 88-55-06
A 65-45-12

Stainless steel available on request.

11

CR, CRI, CRN

GrA3732 - GrA3735

CRN 120 and 150

GrA3731

Construction

CR 120 and 150

TM03 8836 2607

Sectional drawing

TM03 8835 2607

Sectional drawing

Materials: CRN

Materials: CR
Pos. Designation
1

Pump head

Ductile iron

Motor stool (15-60 Hp)

Cast iron

Motor stool (75-100 Hp)

Ductile iron

3
4
5
6
7

Shaft
Impeller
Chamber
Outer sleeve
O-ring for outer sleeve

Stainless
Stainless
Stainless
Stainless
EPDM or

Base

Ductile iron

Base plate

Ductile iron

steel
steel
steel
steel
FKM

AISI/ASTM

Pos.

A 536
65-45-12
A48-30 B
A 536
65-45-12
AISI 431
AISI 304
AISI 304
AISI 316

1
2

A 536
65-45-12
A 536
65-45-12

Materials
Stainless steel
Cast iron

Motor stool (75-100 Hp) Ductile iron

3
4
5
6
7
8

Shaft
Impeller
Chamber
Outer sleeve
O-ring for outer sleeve
Base

Stainless
Stainless
Stainless
Stainless
EPDM or
Stainless

steel
steel
steel
steel
FKM
steel

Base plate

Ductile iron1)

10

Neck ring

PTFE

11

Cartridge type
PTFE
Silicone carbide

10

Neck ring

PTFE

11

Shaft seal1)
Support bearing
Bearing rings
Rubber parts

Cartridge type

12
13

PTFE
Silicone carbide
EPDM or FKM

14

Base plate

Ductile iron1)

Rubber parts

EPDM or FKM

22 mm shaft, 15-60 Hp. 32 mm shaft, 75-100 Hp.

1)
2)

12

Designation
Pump head
Motor stool (15-60 Hp)

Shaft seal2)
Support bearing
Bearing rings

12
13

1)

Materials

AISI/ASTM
A 351 CF 8M
A48-30 B
A 536
65-45-12
SAF 2205
AISI 316
AISI 316
AISI 316
A 351 CF 8M
A 536
65-45-12

Stainless steel available on request.


22 mm shaft, 15-60 Hp. 32 mm shaft, 75-100 Hp.

A 536
65-45-12

CR, CRI, CRN

Pumped liquids

List of pumped liquids

CR, CRI, CRN pumps are designed to pump thin, nonexplosive liquids, not containing solid particles or
fibers. The liquid must not chemically attack the pump
materials. When pumping liquids with a density and/or
viscosity higher than that of water, oversized motors
must be used, if required.
Whether a pump is suitable for a particular liquid
depends on a number of factors of which the most
important are the chloride content, pH value,
temperature and content of chemicals, oils, etc.
Please note that aggressive liquids (e.g. sea water and
some acids) may attack or dissolve the protective
oxide film of the stainless steel and thus cause
corrosion. The CR, CRI, CRN pump types are suitable
for the following liquids:
CR, CRI
Non-corrosive liquids.
For liquid transfer, circulation and pressure boosting of
cold or hot clean water.
CRN
Industrial liquids.
In systems where all parts in contact with the liquid
must be made of high-grade stainless steel.
CRT
Saline liquids
hypochlorites
acids.
For saline or chloride-containing liquids such as sea
water or oxidizing agents such as hypochlorites, CRT
pumps of titanium are available. See separate product
guide on CRT.

A number of typical liquids are listed on the following


pages.
Other pump versions may be applicable, but those
stated in the list are considered to be the best choices.
The table is intended as a general guide only, and
cannot replace actual testing of the pumped liquids
and pump materials under specific working conditions.
The list should, however, be applied with some caution
as factors such as the following may affect the
chemical resistance of a specific pump version:
concentration of the pumped liquid
liquid temperature
pressure.
Safety precautions must be made when pumping
dangerous liquids.
Notes
D
E
F

Operating conditions

7. Operating conditions

Often with additives.


Density and/or viscosity differ from that of water.
Allow for this when calculating motor output and pump
performance.
Pump selection depends on many factors.
Contact Grundfos.

Risk of crystallization/precipitation in shaft seal

The pumped liquid highly inflammable.

The pumped liquid is combustible.

Insoluble in water.

Low self-ignition point.

13

CR, CRI, CRN

Operating conditions

CR
Pumped liquid

Note

Acetic acid CH3COOH


1, F

Alkaline degreasing agent

D, F
E

Ammonium hydroxide NH4OH


Aviation fuel
Benzoic acid C6H5COOH

1s, 1, 3, 5,
10, 15, 20

32, 45, 64, 90,


120, 150

5 %, 68 F

Acetone CH3COCH3

Ammonium bicarbonate NH4HCO3

Liquid concentration,
liquid temperature

CRN

100 %, 68 F
HQQE

1s, 1, 3, 5,
10, 15, 20

32, 45, 64, 90,


120, 150

HQQE

HQQE/HBQE

HBQE

HQQE/HBQE

HQQE

HQQE/HBQE

HQQV

HQQV/HBQV

HQQE/HBQE

20 %, 86 F
20 %, 104 F

HQQE

HQQE/HBQE

1, 3, 4, F

100 %, 68 F

HQBV

HQQV/HBQV

0,5 %, 68 F
< 248 F

HQQE

HQQE/HBQE

248 F - 356 F

< 194 F

HQQE

HQQE

D, E

30 %, 122 F

HQQE

HQQE

Saturated solution, 122 F

HQQE

HQQE

Chloride-containing water

< 86 F, max. 500 ppm

HQQE

HQQE

Chromic acid H2CrO4

1 %, 68 F

HQQV

HQQV/HBQV

Citric acid HOC(CH2CO2H)2COOH

Boiler water
F
Calcareous water
Calcium acetate (as coolant with inhibitor)
Ca(CH3COO)2
Calcium hydroxide Ca(OH) 2

5 %, 104 F

HQQE

HQQE/HBQE

Completely desalinated water


(demineralized water)

< 248 F

HQQE

HQQE/HBQE

Condensate

< 194 F

HQQE

HQQE

HQQE

HQQE/HBQE

HQQE

HQQE/HBQE

HQQE

HQQE/HBQE

Copper sulfate CuSO4


Corn oil
Diesel oil

10 %, 122 F

D, E, 3

100 %, 176 F

2, 3, 4, F

Domestic hot water (potable water)

HQQE/HBQE

HQQV

HQQV/HBQV

100 %, 68 F

HQBV

HQQV/HBQV

< 248 F

HQQE

HQQE/HBQE

Ethanol (ethyl alcohol) C2H5OH

1, F

100 %, 68 F

HQQE

HQQE/HBQE

Ethylene glycol HOCH2CH2OH

D, E

50 %, 122 F

HQQE

HQQE

Formic acid HCOOH

5 %, 68 F

Glycerine (glycerol)
OHCH2CH(OH)CH2OH

D, E

50 %, 122 F

HQQE

HQQE/HBQE

Hydraulic oil (mineral)

E, 2, 3

100 %, 212 F

HQQV

HQQV/HBQE

Hydraulic oil (synthetic)

E, 2, 3

100 %, 212 F

HQQV

HQQV/HBQE

Isopropyl alcohol CH3CHOHCH3

1, F

100 %, 68 F

HQBV

HQQV/HBQV

Lactic acid CH 3CH(OH)COOH

E, H

10 %, 68 F

Linoleic acid C 17H31COOH

E, 3

100 %, 68 F

Methanol (methyl alcohol) CH 3OH


Motor oil
Naphthalene C10H8
Nitric acid HNO3

Olive oil
Oxalic acid (COOH)2

Petrol/gasoline

HQQV/HBQV

1, F

100 %, 68 F

HQQE

HQQE/HBQE

100 %, 176 F

HQQV

HQQV/HBQV

E, H

100 %, 176 F

HQQV

HQQV/HBQV

1 %, 68 F
< 212 F

HQQV

HQQV/HBQV

D, E, 3

100 %, 176 F

HQQV

HQQV/HBQV

1 %, 68 F

HQQE

HQQE/HBQE

1 PPM, < 105 F

HQQE

HQQE/HBQE

Ozone-containing water (O3)


Peanut oil

HQQV

E, 2, 3

Oil-containing water

14

HQQE

D, E, 3

100 %, 194 F

HQQV

HQQV/ HBQV

1, 3, 4, F

100 %, 68 F

HQBV

HQQV/HBQV

7
CR

CRN

Note

Liquid concentration,
liquid temperature

20 %, 68 F

Propanol C3H7OH

1, F

100 %, 68 F

Propylene glycol CH3CH(OH)CH2OH

D, E

50 %, 194 F

HQQE

HQQE

20 %, 122 F

HQQE

HQQE

D, E

30 %, 122 F

HQQE

HQQE

20 %, 122 F

HQQE

HQQE

5 %, 68 F

HQQE

HQQE/HBQE

HQQE

HQQE/HBQE

HQQE

HQQE/HBQE

HQQE

HQQE

Pumped liquid

Phosphoric acid H3PO4

Potassium carbonate K2CO3


Potassium formate (as coolant with inhibitor)
KOOCH
Potassium hydroxide KOH
Potassium permanganate KmnO4
Rape seed oil
Salicylic acid C 6H4(OH)COOH
Silicone oil
Sodium bicarbonate NaHCO3
Sodium chloride (as coolant) NaCl
Sodium hydroxide NaOH

D, E, 3

100 %, 176 F

0,1 %, 68 F

E, 3

100 %

10 %, 140 F

D, E

30 %, < 41 F, pH > 8

20 %, 122 F

1s, 1, 3, 5,
10, 15, 20

HQQV

HQQV

HQQV

HQQE

32, 45, 64, 90,


120, 150

1s, 1, 3, 5,
10, 15, 20

32, 45, 64, 90,


120, 150

HQQV

HQQV/HBQV

HQQV/HBQV

HQQV/HBQV

HQQV/HBQV

HQQE

Sodium hypochlorite NaOCl

0,1 %, 68 F

HQQE

HQQE

Sodium nitrate NaNO3

10 %, 140 F

HQQE

HQQE/HBQE

Sodium phosphate Na3PO4

E, H

10 %, 140 F

HQQE

HQQE

Sodium sulfate Na2SO4

E, H

10 %, 140 F

HQQE

HQQE/HBQE

HQQE

HQQE/HBQE

D, E, 3

100 %, 176 F

1 %, 68 F

HQQV

HQQV/HQQV

1 %, 68 F

HQQE

HQQE/HBQE

Softened water
Soybean oil
Sulfuric acid H2SO4
Sulfurous acid H2SO3
Swimming pool water (low chloride)

< 248 F

Max 5 ppm free chlorine (Cl2)

HQQV

HQQE

Operating conditions

CR, CRI, CRN

HQQV/HBQV

HQQE/HBQE

15

CR, CRI, CRN

Operating conditions

Working and inlet pressure


Max. working pressure and temperature range
ANSI, Clamp, PJE

Max.
working
pressure
[psi]
CR, CRI, CRN 1s
CR, CRI, CRN 1
CR, CRI, CRN 3
CR, CRI, CRN 5
CR 10-1 CR 10-6
CRI, CRN 10-1 CRI, CRN 10-10
CR 15-1 CR 15-5
CRI, CRN 15-1 CRI, CRN 15-8
CR 20-1 CR 20-5
CRI, CRN 20-1 CRI, CRN 20-7

16

232
232
232
232
145
232
145
232
145
232

TM02 8835 0904

TM02 1379 1101

Oval flange

Liquid temp.
range
[F]
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4

to
to
to
to
to
to
to
to
to
to

+248
+248
+248
+248
+248
+248
+248
+248
+248
+248

CR, CRI, CRN 1s


CR, CRI, CRN 1
CR, CRI, CRN 3
CR, CRI, CRN 5
CR, CRI 10-1 10-10
CR, CRI 10-12 10-17
CRN 10 (all stages)
CR, CRI 15-1 15-8
CR, CRI 15-9 15-12
CRN 15 (all stages)
CR, CRI 20-1 20-7
CR, CRI 20-8 20-10
CRN 20 (all stages)
CR, CRN 32-1-1 2-5
CR, CRN 32-6-2 32-11-2
CR, CRN 45-1-1 45-4-2
CR, CRN 45-4-1 45-8-1
CR, CRN 64-1-1 64-3
CR, CRN 64-4-2 64-5-2
CR, CRN 90-1-1 90-3
CR, CRN 90-4-2 90-4-1
CR, CRN 120-1-1 120-5-1
CR, CRN 150-1-1 150-4-1

Max.
working
pressure
[psi]

Liquid temp.
range
[F]

362
362
362
362
232
362
362
232
362
362
232
362
362
232
435
232
435
232
435
232
435
435
435

-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-4 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248
-22 to +248

Operating range of the shaft seal


The operating range of the shaft seal depends on
operating pressure, pump type, type of shaft seal and
liquid temperature. The following curves apply to clean
water and water with anti-freeze liquids. For selecting
the right shaft seal, see Pumped liquids on page 13.
CR 1s - CR 20
p
[psi]
400

20

300

15

200

10
5

HQQE

0
-80

Fig. 5

HBQV

HUBV
HQQE
HQQV

100

HBQE

HUBE

-40

-60 -40

-20

40
0

80

120

20

40

160

60

200

80

240 t [F ]

100

t [C ]

TM05 9659 4213

25

HQQE

HQQV

HQQE

p
[bar]

Shaft
seal

Max. temp. range


[F]

Description
O-ring (cartridge) (balanced
SiC/SiC, EPDM
O-ring (cartridge) (balanced
Carbon/SiC, EPDM
O-ring (cartridge) (balanced
Carbon/SiC, FKM
O-ring (cartridge) (balanced
SiC/SiC, FKM
O-ring (cartridge) (balanced
TC/carbon, EPDM
O-ring (cartridge) (balanced
TC/carbon, FKM

Operating conditions

CR, CRI, CRN

seal),
seal),
seal),
seal),
seal),
seal),

-40 F to +248 F
+32 F to +248 F
+32 F to +194 F
-4 F to +194 F
+32 F to +248 F
+32 F to +194 F

Note: TC= tungsten carbide


See section Lists of variants - on request on page 77,
in case of extreme temperatures:
low temperatures down to -40 F or
high temperatures up to +356 F.

Operating range of standard shaft seals for


CR 1s - CR 20

CR 32 - CR 150 (3.0-60 Hp)

HUB E / HUBV

HUB E

HQQE / HQQV

HQQE

400
300
200
100
0
-40
-40

Fig. 6

40

-20

80
20

120
40

160

60

200

80

240 t [F ]

100

t [C ]

TM06 0999 1314

30
25
20
15
10
5
0

p
[ps i]
500

HQQE

p
[bar]

Operating range of standard shaft seals for


CR 32 - CR 150 (3.0-60 Hp)

CR 120 - CR 150 (75-100 Hp)


p
[bar]

300

15

200

10
5

HQQE/V

HQQE

HBQE/V

HBQE

100

-80
-60

Fig. 7

-40

-40

-20

40
0

80
20

120
40

60

160
80

200
100

240 t [F]
t [C]

TM06 0051 4713

20

HQQV
HQQE

400
HQQE

25

p
[psi]

Operating range of standard shaft seals for


CR 120 - CR 150 (75-100 Hp)

17

CR, CRI, CRN

Operating conditions

Maximum inlet pressure


The following table shows the maximum permissible
inlet pressure. However, the current inlet pressure +
the pressure against a closed valve must always be
lower than the maximum permissible operating
pressure.
If the maximum permissible operating pressure is
exceeded, the bearing in the motor may be damaged
and the life of the shaft seal reduced.
Stages
Pump type
CR, CRI, CRN 1s
CR, CRI, CRN 1
CR, CRI, CRN 3
CR, CRI, CRN 5
CR, CRI, CRN 10
CR, CRI, CRN 15
CR, CRI, CRN 20
CR, CRN 32

CR, CRN 45

CR, CRN 64

60 Hz

50 Hz

2-27
2-25
27
2-17
19-25
2-9
10-24
1-5
6-17
1-2
3-12
1
2-10
1-1 - 2
3-2 - 6
7-2 - 11-2
1-1 - 1
2-2 - 3
4-2 - 8-1
1-1
1 - 2-1
2 - 5-2

2-36
2-36

CR, CRN 90

CR, CRN 120

CR, CRN 150

18

1-1 - 1
2-2 - 4-1
1-1 - 1
2-2 - 3
4-1 - 5-1
1-1
1-2
3-2 - 4-1

2-29
31-36
3-16
18-36
1-6
7-22
1-3
4-17
1-3
4-17
1-1 - 4
5-2 - 10
11-14
1-1 - 2
3-2 - 5
6-2 - 13-2
1-1 - 2-2
2-1 - 4-2
4-1 - 8-1
1-1 - 1
2-2 - 3-2
3-6
1 - 2-1
2 - 5-1
6-1 - 7
1-1 - 1
2-1 - 4-1
5-2 - 6

Max.
[psi (bar)]
145 (10)
145 (10)
217 (15)
145 (10)
217 (15)
145 (10)
217 (15)
116 (8)
145 (10)
116 (8)
145 (10)
116 (8)
145 (10)
58 (4)
145 (10)
217 (15)
58 (4)
145 (10)
217 (15)
58 (4)
145 (10)
217 (15)
58 (4)
145 (10)
217 (15)
145 (10)
217 (15)
290 (20)
145 (10)
217 (15)
290 (20)

Example of operating and inlet pressures


The values for operating and inlet pressures shown in
the tables must not be considered individually but must
always be compared, see the following examples:
Example 1:
The following pump type has been selected: CR 3-10
A-A-A
Max. operating pressure: 232 psi
Max. inlet pressure: 145 psi
Discharge pressure against a closed valve: 139.2 psi,
see page 43.
This pump is not allowed to start at an inlet pressure of
145 psi, but at an inlet pressure of 232.0 - 139.2 =
92.8 psi.
Example 2:
The following pump has been selected: CR 10-2 A-GJA
Max. operating pressure: 232 psi
Max. inlet pressure: 116 psi
Discharge pressure against a closed valve: 42 psi
(97 ft), see page 49.
This pump is allowed to start at an inlet pressure of
116 psi, as the discharge pressure is only 42 psi, which
results in an operating pressure of 116 + 42 = 158 psi.
On the contrary, the max. operating pressure of this
pump is limited to 158 psi, as a higher operating
pressure will require an inlet pressure of more than
116 psi.
In case the inlet or operating pressure exceeds the
pressure permitted, see section Lists of variants - on
request on page 77.

CR, CRI, CRN

Selection and sizing

8. Selection and sizing


Selection of pumps
Selection of pumps should be based on
The duty point of the pump (see section 1)
Sizing data such as pressure loss as a result of
height differences, friction loss in the pipework,
pump efficiency etc. (see section 2)
Pump materials (see section 3)
Pump connections (see section 4)
Shaft seal (see section 5).

H
[ft]

260
240
220

-10-2

850

-9

850

800

-9-2

800

750

-8

750

-8-2

700
650

180

600

450

120

400

-6
-6-2

60
40

P2
[kW]
2
1
0

250
200
150

50

-3-2

250

-2
-2-1
-2-2

200

-1
-1-1

100

220

20

40

60

10

80
15

100
20

120
25

140
30

160
35

180
40

200
45

P2 1/1

Eff

Q [m/h]

100

P2 2/3

Eff
[%]

40

20

0
20

40

60

80

100

120

140

160

180

200

Q [US GPM]

30

H
[ft]

30
20

10

10

NPSHR

0
20

40

60

80

100

120

140

160

180

200

Q [US GPM]

80

60

-9

850

-9-2

800

750

-8

750

-8-2

700

60
40

P2
[kW]
2
1

Example of a curve chart

When sizing a pump the following must be taken into


account.
Required flow and pressure at the point of use.
Pressure loss as a result of height differences
(Hgeo).
Friction loss in the pipework (H f).
It may be necessary to account for pressure loss in
connection with long pipes, bends or valves, etc.
Best efficiency at the estimated duty point.
NPSH value.
For calculation of the NPSH value, see Minimum
inlet pressure - NPSHA on page 21.

450

-5-2

400

400
-4

350

350

-4-2

300

-3

250
200
150

50

-3-2

250

-2
-2-1
-2-2

200

-1
-1-1

100

150

50

P2
[hp]

0
0

20

40

60

10

80
15

100
20

120
25

140
30

160
35

180
40

200
45

Q [US GPM]
Q [m/h]
P2 1/1

Eff

P2 2/3

3
2

Best
efficiency

Eff
[%]
80
60
40

20

H NPSH
[m] [ft]
8

500

-5

2. Sizing data

550

-6-2

100
20

600

-6

450

Duty
point

650

-7-2

500

900

700

-7

550

300

80

950

-10-2

600

120

2-pole, 60 Hz

H
[ft]

1000

800

650

Q [US GPM]

-10

850

180

140

CR 32
CRN 32

-11-2

900

200

160

Fig. 8

240

50

20

260

150

280

300

-3

H
[ft]

1000

950

350

-4-2

H NPSH
[m] [ft]
8

300

400
-4

350

P2
[hp]

H
[m]

550

450

-5-2

100
20

600

500

-5

300
80

650

-7-2

500

900

700

-7

550

140

100

2-pole, 60 Hz

950

900

200

160

-10

H
[ft]

1000

TM02 0039 1303

280

CR 32
CRN 32

-11-2

950

Before determining the point of best efficiency the


operation pattern of the pump needs to be identified. Is
the pump expected to operate at the same duty point,
then select a CR pump which is operating at a duty
point corresponding with the best efficiency of the
pump.

20

40

60

80

100

120

140

160

180

200

Q [US GPM]

H
[ft]

30

30

20

20

10

10

NPSHR

0
0

20

40

60

80

100

120

140

160

180

200

Q [US GPM]

Fig. 10 Example of a CR pumps duty point

As the pump is sized on the basis of the highest


possible flow, it is important to always have the duty
point to the right of the optimum efficiency point (see
fig. 11, range with check mark). This must be
considered in order to keep efficiency high when the
flow drops.

eff

Optimum point

US GPM

TM02 8579 0504

1000

Sizing data

Efficiency

TM02 0039 4713

H
[m]

NPSHR

Fig. 9

From a duty point it is possible to select a pump on the


basis of the curve charts in the section 9. Performance
curves starting on page 24.

TM02 6711 1403

Hgeo

1. Duty point of the pump

300

Required flow,
required pressure

Hf

Fig. 11 Best efficiency

19

CR, CRI, CRN

In order to achieve optimum operating economy, the


pump should be selected on the basis of the following
criteria:
The max. required duty point should be as close as
possible to the QH curve of the pump.
The required duty point should be positioned so that
P2 is close to the max. point of the 100 % curve.
Between the min. and max. performance curves,
pumps with a VFD have an infinite number of
performance curves each representing a specific
speed. Therefore it may not be possible to select a
duty point close to the 100 % curve.

Note:
The approximated formulas apply on condition that the
system characteristic remains unchanged for nn and
nx and that it is based on the formula H = k x Q2,
where k is a constant.
The power equation implies that the pump efficiency is
unchanged at the two speeds. In practice this is not
quite correct.
Finally, it is worth noting that the efficiencies of the
frequency converter and the motor must be taken into
account if a precise calculation of the power saving
resulting from a reduction of the pump speed is
wanted.
H

Q
n
n
n
-------- = -----Q
n
x
x

Hn
H
n n 2
n
------- = ------
Hx
n x

nn

Hx
nx

H
[ft]

Max. curve

Eta

Eta

Qn

0
Q [US GPM]

TM02 7572 4803

n
------- 1
x

Min. curve

Q
Qx

Q
P

Fig. 12 Min. and max. performance curves

In situations where it is not possible to select a duty


point close to the 100 % curve the affinity equations to
the right can be used. The head (H), the flow (Q) and
the input power (P) are all the appropriate variables for
the motor speed (n).

Qx

Qn
Pn
n n 3
------- = ------
Px
n x

Pn
Px

Fig. 13 Affinity equations

Legend
Hn
Hx
Qn
Qx

Rated head in feet


Current head in feet
Rated flow in US gpm
Current flow in US gpm

nn

Rated motor speed in min-1 (n n = 3500 min-1)

nx

Current motor speed in min-1


Rated efficiency in %
Current efficiency in %

n
x

20

TM00 8720 3496

Selection and sizing

Normally, pumps with an external variable frequency


drive (VFD) are used in applications characterized by a
variable flow. Consequently, it is not possible to select
a pump that is constantly operating at optimum
efficiency.

WinCAPS and WebCAPS

6. Inlet pressure and operating pressure

WinCAPS and WebCAPS are both selection programs


offered by Grundfos.
The two programs make it possible to calculate a
pumps specific duty point and energy consumption.
By entering the sizing data of the pump, WinCAPS and
WebCAPS can calculate the exact duty point and
energy consumption. For further information see
16. Further product information on page 83.

Do not exceed the limit values stated on page 16 and


page 18 as regards these pressures:
maximum inlet pressure and
maximum operating pressure.

Selection and sizing

CR, CRI, CRN

Selection of pump connection depends on the rated


pressure and pipework. To meet any requirement the
CR, CRI and CRN pumps offer a wide range of flexible
connections such as:
Oval flange (NPT) - fig. 15
ANSI flange - fig. 15
PJE coupling - fig. 15
Clamp coupling
Union (NPT[M])
Other connections on request.

G (ANSI)

P (PJE)
A (Oval)

Fig. 15 Pump connections

5. Shaft seal
As standard, the CR range is fitted with a Grundfos
shaft seal (Cartridge type) suitable for the most
common applications, see fig. 16.
The following three key parameters must be taken into
account, when selecting the shaft seal:
Type of pumped liquid
liquid temperature and
Maximum pressure.
Grundfos offers a wide range of shaft seal variants to
meet specific demands see Pumped liquids on
page 13.

TM02 1201 0601

4. Pump connection

Fig. 14 CR pump

TM02 0538 4800

The material variant (CR, CRI, CRN) should be


selected based of the liquid to be pumped. The product
range covers three basic types.
The CR, CRI pump types are suitable for clean,
non-aggressive liquids such as potable
water, oils, etc.
The CRN pump type is suitable for industrial liquids
and acids, see Pumped liquids on page 13 or
contact Grundfos.
For saline or chloride-containing liquids such as sea
water, CRT pumps of titanium are available.

TM03 2155 3805

3. Material

Fig. 16 Shaft seal (Cartridge type)

Minimum inlet pressure - NPSHA


Calculation of the inlet pressure "H" is recommended
in these situations:
The liquid temperature is high.
The flow is significantly higher than the rated flow.
Water is drawn from depths.
Water is drawn through long pipes.
Inlet conditions are poor.
To avoid cavitation, make sure that there is a minimum
pressure on the suction side of the pump. The
maximum suction lift "H" in feet can be calculated as
follows:

21

CR, CRI, CRN

Hv
(Ft)

tm
(F)

Hf

370

413

360

328

340

259

320

203

300

148
131
115
98

280

Pb

NPSHR

Hv

270

82

250

66

230

49

212

39
33
26

194
176
158
140
122
104
86
68
50
32

20
16
13
10
6.6
4.9
3.3
2.6
2.0
1.3
0.9
0.7
0.3

TM02 7729 3903

Selection and sizing

H = Pb - NPSHR - Hf - Hv - Hs
Pb
= Barometric pressure in feet absolute.
(Barometric pressure can be set to 33.9
feet. At sea level. In closed systems, pb
indicates system pressure in feet.)
NPSHR = Net Positive Suction Head Required in feet.
(To be read from the NPSHR curve at the
highest flow the pump will be delivering).
= Friction loss in suction pipe in feet.
Hf
(At the highest flow the pump will be
delivering.)
= Vapor pressure in feet.
Hv
(To be read from the vapor pressure scale.
"Hv" depends on the liquid temperature
"Tm").
= Safety margin = minimum 2.0 feet.
Hs
If the "H" calculated is positive, the pump can operate
at a suction lift of maximum "H" feet.
If the "H" calculated is negative, an inlet pressure of
minimum "H" feet is required.

Fig. 17 Minimum inlet pressure - NPSHR

Note: In order to avoid cavitation never, select a pump


whose duty point lies too far to the right on the NPSHR
curve.
Always check the NPSHR value of the pump at the
highest possible flow.
In case a lower NPSHR value is required, see Lists of
variants - on request on page 77.

22

CR, CRI, CRN

H
[ft]

1000

950
280
260
240

Number of stages.
First figure: number of
stages; second figure:
number of reduceddiameter impellers.

The eff curve shows the


efficiency of the pump.
The eff curve is an average
curve of all the pump types
shown in the chart.
The efficiency of pumps
with reduced-diameter
impellers is approx. 2 %
lower than the eff curve
shown in the chart.

220

-9

850

800

-9-2

800

750

-8

750

-8-2

700

600

450

120

400

40

P2
[kW]
2
1
0

400
-4

350

-4-2

300

-3

250
200
150

50

-3-2

250

-2
-2-1
-2-2

200

-1
-1-1

100

150

50

0
0

20

40

60

10

80
15

100
20

120
25

140
30

160
35

180

200

40

Q [US GPM]
Q [m/h]

45

P2 1/1

Eff

P2 2/3

20
0
20

40

60

80

100

120

140

160

180

200

Q [US GPM]

30

H
[ft]

30

20

60
40

80

1
0

The power curves


indicate pump input
power per stage.
Curves are shown for
complete (1/1) and for
reduced-diameter (2/3)
impellers.

Eff
[%]

H NPSH
[m] [ft]
8

450

-5-2

350

P2
[hp]

QH curve for the


individual pump.
The bold curves indicate
the recommended
performance range for
best efficiency.

500

-5

100
20

550

-6-2

300

60

600

-6

500

140

650

-7-2

550

900

700

-7

Pump type, number of


poles and frequency.

950

850

180

80

2-pole, 60 Hz

-10-2

650

100

-10

H
[ft]

1000

900

200

160

CR 32
CRN 32

-11-2

The NPSHR curve is an


average curve for all the
variants shown.
When sizing the pumps,
add a safety margin of at
least 2.0 feet.

TM02 0039 4713

H
[m]
300

Selection and sizing

How to read the curve charts

20

10

10

NPSHR

0
0

20

40

60

80

100

120

140

160

180

200

Q [US GPM]

Fig. 18 How to read the curve charts

Guidelines to performance curves


The curve below shows the minimum flow rate as a
percentage of the nominal flow rate in relation to the
liquid temperature. The dotted line shows a CR pump
fitted with an air-cooled top assembly.
b

Qmin
[%]
30
20
10
0
104
40 140
60 176
80 212
100 248
120 284
140 320
160 356
180
40

60

t [F]

80 100 120 140 160 180 t

[C]

TM02 7538 3703

The guidelines below apply to the curves shown on the


following pages:
1. The motors used for the measurements are
standard motors (ODP, TEFC).
2. Measurements have been made with airless water
at a temperature of 68 F (20 C).
3. The curves apply to a kinematic viscosity of = 1
mm2/s (1 cSt).
4. Due to the risk of overheating, the pumps should
not be used at a flow below the minimum flow rate.
5. The QH curves apply to actual speed with the motor
types mentioned at 60 Hz.

Fig. 19 Minimum flow rate

23

Performance curves

CR, CRI, CRN

Performance curves

9. Performance curves
CR, CRI, CRN 1s
H
[m]

H
[ft]

CR 1s
CRI 1s
CRN 1s

-27

750
220
700
200

180

-25

650

60 Hz, 2-pole

-23

600

H
[ft]
750
700
650
600

-21

550

550
-19

160
500

500
-17

140

450

450
-15

120

400

400
-13

350
100
300
80

350

-12
-11

300

-9

250

-7

200

-10
250
-8

60

200
-6
150
-4

100

100

-3
-2

50

50

0
0.0

0.5

1.0

1.5

2.0

0.0

2.5

3.0

3.5

4.0

0.5

4.5

5.0

5.5

1.0

Q [US GPM]
Q [m/h]

P2
P2
[kW] [hp]
0.04

0.06

Eff
[%]
30

P2

0.04
0.02
0.00

20

0.02

10

Eff

0.00

0
0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

5.5

Q [US GPM]

H NPSH
[m] [ft]
4

H
[ft]

15

15

10
2
0

0
0.0

24

10

NPSHR

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

5.5

Q [US GPM]

TM02 5741 1303

20

150

-5

40

Performance curves

Performance curves

CR, CRI, CRN

CR, CRI, CRN 1

240

H
[ft]

800
750

220
200
180

-25

700

2-pole, 60 Hz

-23

650

-21

550

100

60
40

400

-12

350
-11
300

-10
-9

250

250

-8

200

-7

200

-5

150

-6
150
-4

100

-3
-2

50

50

0
0

P2
[kW]

400

-13

100
20

450

-15

300
80

500

-17

350

P2
[hp]

0.0

0.5

1.0

1.5

10

2.0

11

12Q

0.00

[US GPM]
Q [m/h]

2.5

P2

0.08
0.04

Eff

0.04
0.00

40

H NPSH
[m] [ft]

10

11

12Q

[US GPM]

10

Eff
[%]

20

700

550

500

120

750

600

-19

450

800

650

600

160
140

CR 1
CRI 1
CRN 1

-27

H
[ft]

H
[ft]
10

NPSHR

0
0

10

11

12Q

[US GPM]

TM02 4083 4713

H
[m]

25

Performance curves

CR, CRI, CRN

Performance curves

CR, CRI, CRN 3

240

H
[ft]

800

CR 3
CRI 3
CRN 3

-25

750
220
200
180

-23

700

2-pole, 60 Hz
-21

650

120
100

500
-15

450
400

-13

350

-11

60
40

250

0.10
0.05
0.00

350

-10

300

-8

250

-7

200

200

-6
-5

150

150
-4

100

-3
-2

50

50

0
0

P2
[kW]

400

-9

100
20

450

-12

300
80

P2
[hp]

0.0

2
0.5

1.0

8
1.5

10
2.0

12
2.5

14
3.0

16
3.5

18
4.0

20

22

Q [US GPM]

4.5

5.0

Q [m/h]

0.15

P2

0.10

Eff

0.05
0.00
2

10

12

14

16

18

20

22

Q [US GPM]

10

40

H
[ft]
10

NPSHR

0
0

26

60

H NPSH
[m] [ft]

Eff
[%]

20

700

550

-17

500
140

750

600

-19

550

800

650

600

160

H
[ft]

10

12

14

16

18

20

22

Q [US GPM]

TM02 4084 4713

H
[m]

Performance curves

Performance curves

CR, CRI, CRN

CR, CRI, CRN 5

240

H
[ft]

CR 5
CRI 5
CRN 5

800

-24
750

220
200
180

700

-22

650

2-pole, 60 Hz

-20

550
-16

500
-15

-14

450

450
-13

400

60
40

-11

350

350

-10
300

-9
-8

250

250
-7

200

200

-6

150

-5

150

-3

100

-4

100
20

400

-12

300
80

700

600

500

100

750

-18
550

120

800

650

600

160
140

H
[ft]

-2

50

50

0
0
0

5
1

10
2

15
3

20
4

25
5

30
6

35
7

40

Q [US GPM]

10

Q [m/h]

P2
[kW]

P2
[hp]

0.2

0.2

40

0.1

0.1

20

0.0

0.0

P2
Eff

0.3

H NPSH
[m] [ft]

10

15

20

25

30

35

40

Q [US GPM]

15

H
[ft]

15

10
2

60

0
0

Eff
[%]

10
NPSHR

0
0

10

15

20

25

30

35

40

Q [US GPM]

TM02 4085 4713

H
[m]

27

Performance curves

CR, CRI, CRN

Performance curves

CR, CRI, CRN 10


H
[m]

260
240

H
[ft]
850

CR 10
CRI 10
CRN 10

-17

800

-16

750
220

2-pole, 60 Hz

700

200

650

180

600

-14

H
[ft]
850
800
750
700
650
600

-12

550

550

160

120
100
80
60
40
20
0

-10

500

450

-9

450

400

-8

400

350

-7

350

300

-6

300

250

-5

250

200

-4

200

150

-3

150

100

-2

100

-1

50
0

0
0

P2
[kW]
0.4
0.2
0.0

P2
[hp]

15
3

20
4

25
5

30
6

35

40

45
10

50
11

55
12

Q [US GPM]

60
13

14

15

Q [m/h]
P2
Eff

Eff
[%]
80
60

0.4

40

0.2

20

0.0

0
5

10

15

20

25

30

35

40

45

50

55

60

Q [US GPM]

NPSH
[ft]

15

15

10

10
NPSHR

0
0

28

10

0.6

H NPSH
[m] [ft]

0.8

50

10

15

20

25

30

35

40

45

50

55

60

Q [US GPM]

TM02 7221 4713

140

500

Performance curves

Performance curves

CR, CRI, CRN

CR, CRI, CRN 15

240

H
[ft]

CR 15
CRI 15
CRN 15

-12

800
750

220
200
180

700

2-pole, 60 Hz

-10
650
-9

600
550

100

60
40

500
-7

450

450

400

-6

400

350

-5

350

P2
[kW]
1.0
0.5
0.0

250

250
-3

200
150

2
0

150
100

-1

50

50

P2
[hp]

0
0

10

20
4

30
6

40
8

50
10

12

60
14

70

80

16

18

90
20

2.0

Eff

1.5

P2

100
22

Q [US GPM]

110
24

26

28

Q [m/h]

Eff
[%]
80
60

1.0

40

0.5

20

0.0

H NPSH
[m] [ft]
4

200

-2

300

-4

100
20

700

550

-8

300
80

750

600

500

120

800

650

160
140

H
[ft]

10

20

30

40

50

60

70

80

90

100

110

Q [US GPM]

H
[ft]

20

20

15

15

10

10

NPSHR

0
0

10

20

30

40

50

60

70

80

90

100

110

Q [US GPM]

TM02 7222 4713

H
[m]

29

Performance curves

CR, CRI, CRN

Performance curves

CR, CRI, CRN 20


H
[m]

H
[ft]

CR 20
CRI 20
CRN 20

750
220

-10

700
200

180

650

2-pole, 60 Hz

600

H
[ft]
750
700
650
600

-8

550

550

160
500
140

500

-7

450

450
-6

120

400

400
-5

350

350

100
300

60

40

250

250
-3

200
150

P2
[kW]
2
1
0

50

50

P2
[hp]

0
0

10

30
6

40
8

50
10

12

60
14

70

80

16

18

90
20

100
22

110
24

26

120
28

130
30

140
32

Q [US GPM]
34

Q [m/h]

Eff
[%]
80

Eff
P2

2
1

60
40
20

0
10

20

30

40

50

60

70

80

90

100

110

120

130

140

Q [US GPM]

H
[ft]

30

30

20

20

10

10

NPSHR

0
0

30

20

H NPSH
[m] [ft]

100

-1

150

-2

100
20

200

10

20

30

40

50

60

70

80

90

100

110

120

130

140

Q [US GPM]

TM02 7223 4713

80

300

-4

Performance curves

Performance curves

CR, CRI, CRN

CR, CRN 32

300

H
[ft]

1000

950
280
260
240
220
200
180
160
140
120
100

-10

900

-10-2

850

-9

60
40

750

P2
[kW]
2
1
0

600
550

-6-2

500

500

-5

450

450

-5-2

400

400
-4

350

350

-4-2

300

-3

250
200
150

50

-3-2

250

-2
-2-1
-2-2

200

-1
-1-1

100

150

50

P2
[hp]

0
0

20

40

60

10

80
15

100
20

120
25

140
30

160
35

180
40

200
45

Q [US GPM]
Q [m/h]
P2 1/1

Eff

P2 2/3

Eff
[%]
80
60

40

20

H NPSH
[m] [ft]

650

-6

550

700

-7-2

600

900

750

-7

650

950

800

-8-2

700

1000

850

-8

100
20

2-pole, 60 Hz

-9-2

800

300
80

CR 32
CRN 32

-11-2

H
[ft]

20

40

60

80

100

120

140

160

180

200

Q [US GPM]

H
[ft]

30

30

20

20

10

10

NPSHR

0
0

20

40

60

80

100

120

140

160

180

200

Q [US GPM]

TM02 0039 4713

H
[m]

31

Performance curves

CR, CRI, CRN

Performance curves

CR, CRN 45

280
260
240

H
[ft]

950
900

-7

850

200
180
160

650
-5
-5-1
-5-2

550
500

400

60
40

P2
[kW]
4
2
0

350

250

200
150

350
300
250
200
150

-1
-1-1

100

50

50

P2
[hp]

0
0

20

40
10

60

80

15

100
20

120
25

140
30

160
35

180
40

200

220

240

45

50

55

260
60

280
65

Q [US GPM]
Q [m/h]
P2 1/1
Eff
P2 2/3

8
6

Eff
[%]
80
60

40

20

0
20

40

60

80

100

120

140

160

180

200

220

240

260

280

Q [US GPM]

H
[ft]

30

30

20

20

10

10

NPSHR

0
0

32

450

-2
-2-1
-2-2

H NPSH
[m] [ft]

500

400

550

-3
-3-1
-3-2

100
20

600

-4
-4-1
-4-2

300
80

850

700

-6-2

600

120

900

750

650

450

950

800

-6

700

140

100

2-pole, 60 Hz

-7-2

800
750

220

CR 45
CRN 45

-8-1

H
[ft]

20

40

60

80

100

120

140

160

180

200

220

240

260

280

Q [US GPM]

TM02 0040 4713

H
[m]

Performance curves

Performance curves

CR, CRI, CRN

CR, CRN 64
H
[m]
180

H
[ft]
600

-5-2

550

-4

160

2-pole, 60 Hz

-4-1

500
140

CR 64
CRN 64

600
550
500

-4-2

450

H
[ft]

450

-3
120

400

400
-3-1

350

350

100

-3-2
300

300
-2

60

250
200

150

-1

150

100

-1-1

100

50

50

0
0

P2
[kW]
8
4
0

P2
[hp]

10

80
20

120

160

30

200
40

240
50

280
60

320
70

360
80

400
90

Q [US GPM]
Q [m/h]

12

Eff
P2 1/1

P2 2/3

Eff
[%]
80
60
40
20

H NPSH
[m] [ft]

40

16

200

-2-2

40

20

250

-2-1

40

80

120

160

200

240

280

320

360

400

Q [US GPM]

H
[ft]

30

30

20

20

10

10

NPSHR

0
0

40

80

120

160

200

240

280

320

360

400

Q [US GPM]

TM02 0041 4713

80

33

Performance curves

CR, CRI, CRN

Performance curves

CR, CRN 90
H
[m]
180

H
[ft]

CR 90
CRN 90

600
-4-1

2-pole, 60 Hz

550
160

600

550

-4-2
500

140

H
[ft]

500
-3

450

450

-3-1
120

400

400
-3-2

350

350

100
-2

300
80

300

-2-1
250

250
-2-2

60

200

200
-1

150

150

40
-1-1
100

100

50

50

20

0
0

P2
P2
[kW] [hp]

50

10

100

20

150

30

200

40

250

50

60

300

350

400

70

80

90

450

100

500

110

550

120

130

4
0

140

Q [m/h]
P2 1/1
Eff
P2 2/3

16
8

600 Q [US GPM]

12

40
20

0
50

100

150

200

250

300

350

400

450

500

550

600 Q [US GPM]

H
[ft]

30

30

20

20

10

10

NPSHR

0
0

34

60

H NPSH
[m] [ft]

80

Eff
[%]

50

100

150

200

250

300

350

400

450

500

550

600 Q [US GPM]

TM02 0042 1303

Performance curves

Performance curves

CR, CRI, CRN

CR, CRN 120


H
[m]

H
[ft]
700

200

180

650

5-2

4
4-1

160

4-2

500

120

2-pole, 60 Hz

600
550

140

CR 120
CRN 120

5-1

450

-3
3-1

400

3-2

350
100

80

60

300

250

2-1
2-2

200

150
40

1-1
100

50
0
0

50

P2
[kW]
15
10
5
0

40

250

300

60

350

400

80

450

500

100

550

120

600

140

Q [US GPM]
Q [m/h]

20

Eff

15

P22/3

Eff
[%]
80
60

10

40

20

0
50

100

150

200

250

300

350

400

450

500

550

600

H
[ft]

Q [US GPM]

120

30

QH 3500 rpm2/3

80

10

40

NPSH
[ft]
40

QH 3500 rpm1n

30
20

20

200

P21n

160
40

150

P2
[hp]

H
[m]

100

20
NPSH

10
0

50

100

150

200

250

300

350

400

450

500

550

600

Q [US GPM]

TM03 9192 0209

20

35

Performance curves

CR, CRI, CRN

Performance curves

CR, CRN 150


H
[m]
180

H
[ft]
600

CR 150
CRN 150

4-1

550

2-pole, 60 Hz

4-2

160
500

3
140

450
3-1

120

400
3-2
350

100

2
300

80

2-1
250
2-2

40

200
1

150

1-1

100
20

50
0
0

P2
[kW]
20
15
10

P2
[hp]

300

60

350

400

80

450
100

500

550

120

600

650

140

700

Q [US GPM]

160

Q [m/h]

Eff

Eff
[%]
80

16

P22/3

40

H
[ft]

20
0
0

50

100

150

200

250

300

350

400

450

500

550

600

650

700

Q [US GPM]

NPSH
[ft]

160

QH 3500 rpm1n

40

120

QH 3500 rpm2/3

30

80

10

40

20

NPSH

10
0

36

40

250

60

20

20

200

P21n

30

150

24

40

100

32

H
[m]

50

50

100

150

200

250

300

350

400

450

500

550

600

650

700

Q [US GPM]

TM03 9193 4213

60

Technical data

10
Technical data

CR, CRI, CRN

10. Technical data


CR 1s
D2

D2

D1

PRIMING
PORT (G 1/2)

DRAIN
PLUG (G 1/2)

13/16"

2"

TM03 1450 2205

M10 x 40

3 15/16"
5 11/16"
6 5/16"

4 x 1/2"
3"
7 1/16"
8 11/16"

3/4"x1"

3"

7/8"

5 1/2"

1"NPT (F)
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 15/16"
5 9/16"
9 7/8"

13/16"

B1

B1

1 1/4"250 lb.R.F.
SUCTION AND
DISCHARGE

TM03 1451 2205

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

3 1/2"
3 15/16"

B2

B2

D1

4 x 1/2"
1 3/8"
7 1/16"
8 11/16"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

Oval*
D1

CR 1s-2

1/3

CR 1s-3

1/3

CR 1s-4

1/3

CR 1s-5

1/3

CR 1s-6

1/2

CR 1s-7

1/2

CR 1s-8

1/2

CR 1s-9

3/4

CR 1s-10

3/4

CR 1s-11

3/4

CR 1s-12

3/4

CR 1s-13

CR 1s-15

CR 1s-17

1 1/2

CR 1s-19

1 1/2

CR 1s-21

1 1/2

CR 1s-23

1 1/2

CR 1s-25

CR 1s-27

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

11.97 (305)
11.97 (305)
11.97 (305)
11.97 (305)
12.68 (323)
12.68 (323)
13.39 (341)
13.39 (341)
14.09 (358)
14.09 (358)
14.80 (376)
14.80 (376)
15.51 (394)
15.51 (394)
16.22 (412)
16.22 (412)
16.93 (431)
16.93 (431)
17.64 (449)
17.64 (449)
18.35 (467)
18.35 (467)
19.06 (485)
19.06 (485)
20.47 (520)
20.47 (520)
21.89 (557)
21.89 (557)
23.31 (593)
23.31 (593)
24.72 (628)
24.72 (628)
26.14 (664)
26.14 (664)
27.56 (701)
27.56 (701)
28.98 (737)
28.98 (737)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
7.01
7.19
7.01

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(179)
(183)
(179)

D2

B1+B2

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)

21.26 (541)
19.41 (494)
21.26 (541)
19.41 (494)
21.97 (559)
20.12 (512)
22.68 (577)
20.83 (530)
23.38 (594)
21.53 (547)
24.09 (612)
22.24 (565)
24.80 (630)
22.95 (583)
26.13 (664)
23.66 (601)
26.84 (682)
24.37 (619)
27.55 (700)
25.08 (638)
28.26 (718)
25.79 (656)
30.25 (769)
26.50 (674)
31.66 (805)
27.91 (709)
33.57 (853)
30.51 (775)
34.99 (889)
31.93 (812)
36.40 (925)
33.34 (847)
37.82 (961)
34.76 (883)
40.12 (1020)
38.78 (986)
41.54 (1056)
40.20 (1022)

69 (32)
67 (31)
69 (32)
67 (31)
70 (32)
68 (31)
71 (33)
69 (32)
75 (35)
70 (32)
76 (35)
71 (33)
77 (35)
72 (33)
82 (38)
73 (34)
83 (38)
74 (34)
84 (39)
75 (35)
85 (39)
76 (35)
101 (46)
77 (35)
103 (47)
78 (36)
107 (49)
84 (39)
109 (50)
86 (40)
111 (51)
88 (40)
113 (52)
90 (41)
126 (58)
116 (53)
127 (58)
118 (54)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

37

10

Technical data

CR, CRI, CRN

Technical data

CRI 1s
D2

D2
D1

B2

B2

D1

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

3/4 x 1 1/16"
1/2"

3 1/2"
4 1/8"

DRAIN
PLUG (G 1/2)

M10 x 40

3 15/16"
5 15/16"

3"
7 1/16"
8 5/16"

8 5/16"

3"
3 15/16"
5 15/16"
9 7/8"

1 3/8"

13/16"

2"

TM03 1452 2205

4 x 1/2"

TM03 1453 2205

5 1/2"

DRAIN
PLUG (G 1/2)

B1

1"NPT (F)
SUCTION AND
DISCHARGE

1 11/16"

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

Oval*
D1

CRI 1s-2

1/3

CRI 1s-3

1/3

CRI 1s-4

1/3

CRI 1s-5

1/3

CRI 1s-6

1/2

CRI 1s-7

1/2

CRI 1s-8

1/2

CRI 1s-9

3/4

CRI 1s-10

3/4

CRI 1s-11

3/4

CRI 1s-12

3/4

CRI 1s-13

CRI 1s-15

CRI 1s-17

1 1/2

CRI 1s-19

1 1/2

CRI 1s-21

1 1/2

CRI 1s-23

1 1/2

CRI 1s-25

CRI 1s-27

Ship. wt.
[lbs (kg)]

TEFC
B1
D2

B1+B2

1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
12.09
12.09
12.80
12.80
13.50
13.50
14.21
14.21
14.92
14.92
15.63
15.63

(308)
(308)
(308)
(308)
(326)
(326)
(343)
(343)
(361)
(361)
(379)
(379)
(398)
(398)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)

5.18
4.57
5.18
4.57
5.18
4.57
5.18
4.57
5.18
4.57
5.18
4.57
5.18
4.57

(132)
(117)
(132)
(117)
(132)
(117)
(132)
(117)
(132)
(117)
(132)
(117)
(132)
(117)

21.38
19.53
21.38
19.53
22.09
20.24
22.79
20.94
23.50
21.65
24.21
22.36
24.92
23.07

(544)
(497)
(544)
(497)
(562)
(515)
(579)
(532)
(597)
(550)
(615)
(568)
(633)
(586)

64
62
64
62
65
63
66
64
70
65
71
65
72
66

(30)
(29)
(30)
(29)
(30)
(29)
(30)
(30)
(32)
(30)
(33)
(30)
(33)
(30)

1
3
1
3
1

16.34
16.34
17.05
17.05
17.76

(416)
(416)
(434)
(434)
(452)

6.19
5.55
6.19
5.55
6.19

(158)
(141)
(158)
(141)
(158)

5.18
4.57
5.18
4.57
5.18

(132)
(117)
(132)
(117)
(132)

26.25
23.78
26.96
24.49
27.67

(667)
(605)
(685)
(623)
(703)

77
68
78
69
79

(35)
(31)
(36)
(32)
(36)

3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

17.76
18.46
18.46
19.17
19.17
20.59
20.59
22.01
22.01
23.43
23.43
24.84
24.84
26.26
26.26
27.68
27.68
29.09
29.09

(452)
(469)
(469)
(487)
(487)
(523)
(523)
(560)
(560)
(596)
(596)
(631)
(631)
(668)
(668)
(704)
(704)
(739)
(739)

5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
7.01
7.19
7.01

(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(179)
(183)
(179)

4.57
5.18
4.57
5.73
4.57
5.73
4.57
5.73
4.57
5.73
4.57
5.73
4.57
5.73
4.57
5.73
4.33
5.73
4.33

(117)
(132)
(117)
(146)
(117)
(146)
(117)
(146)
(117)
(146)
(117)
(146)
(117)
(146)
(117)
(146)
(110)
(146)
(110)

25.20 (641)
28.37 (721)
25.90 (658)
30.36 (772)
26.61 (676)
31.78 (808)
28.03 (712)
33.69 (856)
30.63 (779)
35.11 (892)
32.05 (815)
36.52 (928)
33.46 (850)
37.94 (964)
34.88 (886)
40.24 (1023)
38.90 (989)
41.65 (1058)
40.31 (1024)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

38

70 (32)
79 (36)
70 (32)
96 (44)
71 (33)
97 (44)
73 (34)
102 (47)
79 (36)
104 (48)
81 (37)
106 (49)
82 (38)
107 (49)
84 (39)
120 (55)
111 (51)
122 (56)
113 (52)

Technical data

10
Technical data

CR, CRI, CRN

CRN 1s
D2
D2

D1

B2

B2

D1

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

8 1/4"

3 15/16"
5 15/16"
9 7/8"

5 1/2"
4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

TM03 1453 2205

7 1/16"
8 5/16"

3"

TM03 1454 2205

3 15/16"
5 15/16"

13/16"

2"

4 x 1/2"

3/4 x 1 1/16"
1/2"

3 1/2"
4 1/8"

DRAIN
PLUG (G 1/2)

1 1/4" Victaulic-type
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

1 3/8"

B1

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

PJE*
D1

CRN 1s-2

1/3

CRN 1s-3

1/3

CRN 1s-4

1/3

CRN 1s-5

1/3

CRN 1s-6

1/2

CRN 1s-7

1/2

CRN 1s-8

1/2

CRN 1s-9

3/4

CRN 1s-10

3/4

CRN 1s-11

3/4

CRN 1s-12

3/4

CRN 1s-13

CRN 1s-15

CRN 1s-17

1 1/2

CRN 1s-19

1 1/2

CRN 1s-21

1 1/2

CRN 1s-23

1 1/2

CRN 1s-25

CRN 1s-27

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
12.09
12.09
12.80
12.80
13.50
13.50
14.21
14.21
14.92
14.92
15.63
15.63
16.34
16.34
17.05
17.05
17.76
17.76
18.46
18.46
19.17
19.17
20.59
20.59
22.01
22.01
23.43
23.43
24.84
24.84
26.26
26.26
27.68
27.68
29.09
29.09

(308)
(308)
(308)
(308)
(326)
(326)
(343)
(343)
(361)
(361)
(379)
(379)
(398)
(398)
(416)
(416)
(434)
(434)
(452)
(452)
(469)
(469)
(487)
(487)
(523)
(523)
(560)
(560)
(596)
(596)
(631)
(631)
(668)
(668)
(704)
(704)
(739)
(739)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
7.01
7.19
7.01

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(179)
(183)
(179)

D2

B1+B2

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)

21.38 (544)
19.53 (497)
21.38 (544)
19.53 (497)
22.09 (562)
20.24 (515)
22.79 (579)
20.94 (532)
23.50 (597)
21.65 (550)
24.21 (615)
22.36 (568)
24.92 (633)
23.07 (586)
26.25 (667)
23.78 (605)
26.96 (685)
24.49 (623)
27.67 (703)
25.20 (641)
28.37 (721)
25.90 (658)
30.36 (772)
26.61 (676)
31.78 (808)
28.03 (712)
33.69 (856)
30.63 (779)
35.11 (892)
32.05 (815)
36.52 (928)
33.46 (850)
37.94 (964)
34.88 (886)
40.24 (1023)
38.90 (989)
41.65 (1058)
40.31 (1024)

63 (29)
61 (28)
64 (30)
62 (29)
65 (30)
63 (29)
66 (30)
64 (30)
70 (32)
65 (30)
71 (33)
65 (30)
72 (33)
66 (30)
77 (35)
68 (31)
78 (36)
69 (32)
78 (36)
69 (32)
79 (36)
70 (32)
96 (44)
71 (33)
97 (44)
73 (34)
102 (47)
79 (36)
104 (48)
81 (37)
105 (48)
82 (38)
107 (49)
84 (39)
120 (55)
111 (51)
122 (56)
112 (51)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

39

10

Technical data

CR, CRI, CRN

Technical data

CR 1
D2

D2
D1

DRAIN
PLUG (G 1/2)

5 1/2"

3 15/16"
5 9/16"
9 7/8"

13/16"

4 x 1/2"
3"
7 1/16"
8 11/16"

3"

TM03 1450 2205

13/16"

2"

5 11/16"
6 5/16"

3/4"x1"

M10 x 40

4 x 1/2"
1 3/8"
7 1/16"
8 11/16"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

Oval*
D1

CR 1-2

1/3

CR 1-3

1/3

CR 1-4

1/2

CR 1-5

1/2

CR 1-6

3/4

CR 1-7

3/4

CR 1-8

CR 1-9

CR 1-10

1 1/2

CR 1-11

1 1/2

CR 1-12

1 1/2

CR 1-13

1 1/2

CR 1-15

CR 1-17

CR 1-19

CR 1-21

CR 1-23

CR 1-25

CR 1-27

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

11.97 (305)
11.97 (305)
11.97 (305)
11.97 (305)
12.68 (323)
12.68 (323)
13.39 (341)
13.39 (341)
14.09 (358)
14.09 (358)
14.80 (376)
14.80 (376)
15.51 (394)
15.51 (394)
16.22 (412)
16.22 (412)
16.93 (431)
16.93 (431)
17.64 (449)
17.64 (449)
18.35 (467)
18.35 (467)
19.06 (485)
19.06 (485)
20.47 (520)
20.47 (520)
21.89 (557)
21.89 (557)
24.41 (621)
24.41 (621)
25.83 (657)
25.83 (657)
27.24 (692)
27.24 (692)
28.66 (728)
28.66 (728)
30.08 (765)
30.08 (765)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
7.01
7.19
7.01
8.60
7.01
8.60
7.01
8.60
7.01
8.60
7.01
8.60
7.01

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(179)
(183)
(179)
(219)
(179)
(219)
(179)
(219)
(179)
(219)
(179)
(219)
(179)

D2

B1+B2

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)

21.26 (541)
19.41 (494)
21.26 (541)
19.41 (494)
21.97 (559)
20.12 (512)
22.68 (577)
20.83 (530)
24.00 (610)
21.53 (547)
24.71 (628)
22.24 (565)
26.70 (679)
22.95 (583)
27.41 (697)
23.66 (601)
28.61 (727)
25.55 (649)
29.32 (745)
26.26 (668)
30.03 (763)
26.97 (686)
30.74 (781)
27.68 (704)
33.03 (839)
31.69 (805)
34.45 (876)
33.11 (841)
39.06 (993)
37.64 (957)
40.48 (1029)
39.06 (993)
41.89 (1065)
40.47 (1028)
43.31 (1101)
41.89 (1065)
44.73 (1137)
43.31 (1101)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

40

69 (32)
67 (31)
69 (32)
67 (31)
73 (34)
68 (31)
75 (35)
69 (32)
80 (37)
71 (33)
81 (37)
72 (33)
93 (43)
72 (33)
94 (43)
74 (34)
95 (44)
74 (34)
102 (47)
76 (35)
103 (47)
77 (35)
104 (48)
78 (36)
114 (52)
104 (48)
116 (53)
106 (49)
155 (71)
123 (56)
158 (72)
125 (57)
159 (73)
130 (59)
161 (74)
132 (60)
163 (74)
134 (61)

TM03 1451 2205

7/8"

1 1/4"250 lb.R.F.
SUCTION AND
DISCHARGE

B1

B1

1"NPT (F)
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 15/16"

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

3 1/2"
3 15/16"

B2

B2

D1

Technical data

10
Technical data

CR, CRI, CRN

CRI 1
D2

D2
D1

DRAIN
PLUG (G 1/2)

5 1/2"

3 15/16"
5 9/16"
9 7/8"

13/16"

4 x 1/2"
3"
7 1/16"
8 11/16"

3"

TM03 1450 2205

13/16"

2"

5 11/16"
6 5/16"

3/4"x1"

M10 x 40

4 x 1/2"
1 3/8"
7 1/16"
8 11/16"

TM03 1451 2205

7/8"

1 1/4"250 lb.R.F.
SUCTION AND
DISCHARGE

B1

B1

1"NPT (F)
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 15/16"

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

3 1/2"
3 15/16"

B2

B2

D1

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

Oval*
D1

CRI 1-2

1/3

CRI 1-3

1/3

CRI 1-4

1/2

CRI 1-5

1/2

CRI 1-6

3/4

CRI 1-7

3/4

CRI 1-8

CRI 1-9

CRI 1-10

1 1/2

CRI 1-11

1 1/2

CRI 1-12

1 1/2

CRI 1-13

1 1/2

CRI 1-15

CRI 1-17

CRI 1-19

CRI 1-21

CRI 1-23

CRI 1-25

CRI 1-27

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
12.09
12.09
12.80
12.80
13.50
13.50
14.21
14.21
14.92
14.92
15.63
15.63
16.34
16.34
17.05
17.05
17.76
17.76
18.46
18.46
19.17
19.17
20.59
20.59
22.01
22.01
24.53
24.53
25.94
25.94
27.36
27.36
28.78
28.78
30.20
30.20

(308)
(308)
(308)
(308)
(326)
(326)
(343)
(343)
(361)
(361)
(379)
(379)
(398)
(398)
(416)
(416)
(434)
(434)
(452)
(452)
(469)
(469)
(487)
(487)
(523)
(523)
(560)
(560)
(624)
(624)
(659)
(659)
(695)
(695)
(732)
(732)
(768)
(768)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
7.01
7.19
7.01
8.60
7.01
8.60
7.01
8.60
7.01
8.60
7.01
8.60
7.01

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(179)
(183)
(179)
(219)
(179)
(219)
(179)
(219)
(179)
(219)
(179)
(219)
(179)

D2

B1+B2

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)

21.38 (544)
19.53 (497)
21.38 (544)
19.53 (497)
22.09 (562)
20.24 (515)
22.79 (579)
20.94 (532)
24.12 (613)
21.65 (550)
24.83 (631)
22.36 (568)
26.82 (682)
23.07 (586)
27.53 (700)
23.78 (605)
28.73 (730)
25.67 (653)
29.44 (748)
26.38 (671)
30.14 (766)
27.08 (688)
30.85 (784)
27.79 (706)
33.15 (843)
31.81 (808)
34.57 (879)
33.23 (845)
39.18 (996)
37.76 (960)
40.59 (1031)
39.17 (995)
42.01 (1068)
40.59 (1031)
43.43 (1104)
42.01 (1068)
44.85 (1140)
43.43 (1104)

64 (30)
62 (29)
64 (30)
62 (29)
68 (31)
63 (29)
69 (32)
64 (30)
74 (34)
65 (30)
75 (35)
66 (66)
88 (40)
67 (31)
89 (41)
68 (31)
90 (41)
69 (32)
97 (44)
70 (32)
98 (45)
71 (33)
99 (45)
72 (33)
109 (50)
99 (45)
110 (50)
101 (46)
148 (68)
116 (53)
150 (69)
118 (54)
152 (69)
123 (56)
154 (70)
125 (57)
156 (71)
127 (58)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

41

10

Technical data

CR, CRI, CRN

Technical data

CRN 1
D2

D2

D1

B2

B2

D1

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

8 1/4"

3"
3 15/16"
5 15/16"
9 7/8"

4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

PJE*
D1

CRN 1-2

1/3

CRN 1-3

1/3

CRN 1-4

1/2

CRN 1-5

1/2

CRN 1-6

3/4

CRN 1-7

3/4

CRN 1-8

CRN 1-9

CRN 1-10

1 1/2

CRN 1-11

1 1/2

CRN 1-12

1 1/2

CRN 1-13

1 1/2

CRN 1-15

CRN 1-17

CRN 1-19

CRN 1-21

CRN 1-23

CRN 1-25

CRN 1-27

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
12.09
12.09
12.80
12.80
13.50
13.50
14.21
14.21
14.92
14.92
15.63
15.63
16.34
16.34
17.05
17.05
17.76
17.76
18.46
18.46
19.17
19.17
20.59
20.59
22.01
22.01
23.53
23.53
25.94
25.94
27.36
27.36
28.78
28.78
30.20
30.20

(308)
(308)
(308)
(308)
(326)
(326)
(343)
(343)
(361)
(361)
(379)
(379)
(398)
(398)
(416)
(416)
(434)
(434)
(452)
(452)
(469)
(469)
(487)
(487)
(523)
(523)
(560)
(560)
(598)
(598)
(659)
(659)
(695)
(695)
(732)
(732)
(768)
(768)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55
7.19
7.01
7.19
7.01
8.60
7.01
8.60
7.01
8.60
7.01
8.60
7.01
8.60
7.01

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(141)
(183)
(179)
(183)
(179)
(219)
(179)
(219)
(179)
(219)
(179)
(219)
(179)
(219)
(179)

D2

B1+B2

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)

21.38 (544)
19.53 (497)
21.38 (544)
19.53 (497)
22.09 (562)
20.24 (515)
22.79 (579)
20.94 (532)
24.12 (613)
21.65 (550)
24.83 (631)
22.36 (568)
26.82 (682)
23.07 (586)
27.53 (700)
23.78 (605)
28.73 (730)
25.67 (653)
29.44 (748)
26.38 (671)
30.14 (766)
27.08 (688)
30.85 (784)
27.79 (706)
33.15 (843)
31.81 (808)
34.57 (879)
33.23 (845)
39.18 (996)
37.76 (960)
40.59 (1031)
39.17 (995)
42.01 (1068)
40.59 (1031)
43.43 (1104)
42.01 (1068)
44.85 (1140)
43.43 (1104)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

42

64 (30)
62 (29)
64 (30)
62 (29)
68 (31)
63 (29)
69 (32)
64 (30)
74 (34)
65 (30)
75 (35)
66 (30)
88 (40)
67 (31)
89 (41)
68 (31)
90 (41)
69 (32)
97 (44)
70 (32)
98 (45)
71 (33)
99 (45)
72 (33)
108 (49)
99 (45)
110 (50)
101 (46)
148 (68)
116 (53)
150 (69)
118 (54)
152 (69)
123 (56)
154 (70)
124 (57)
155 (71)
126 (58)

TM03 1453 2205

7 1/16"
8 5/16"

3/4 x 1 1/16"
1/2"

1 3/8"

3 15/16"
5 15/16"

13/16"

2"

TM03 1454 2205

4 x 1/2"

DRAIN
PLUG (G 1/2)

3 1/2"
4 1/8"

1 1/4" Victaulic-type
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

5 1/2"

B1

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

Technical data

10
Technical data

CR, CRI, CRN

CR 3
D2

D2
D1

DRAIN
PLUG (G 1/2)

5 1/2"

3 15/16"
5 9/16"
9 7/8"

13/16"

4 x 1/2"
3"
7 1/16"
8 11/16"

3"

TM03 1450 2205

13/16"

2"

5 11/16"
6 5/16"

3/4"x1"

M10 x 40

4 x 1/2"
1 3/8"
7 1/16"
8 11/16"

TM03 1451 2205

7/8"

1 1/4"250 lb.R.F.
SUCTION AND
DISCHARGE

B1

B1

1"NPT (F)
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 15/16"

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

3 1/2"
3 15/16"

B2

B2

D1

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CR 3-2

1/3

CR 3-3

1/2

CR 3-4

3/4

CR 3-5

3/4

CR 3-6

CR 3-7

1 1/2

CR 3-8

1 1/2

CR 3-9

1 1/2

CR 3-10

CR 3-11

CR 3-12

CR 3-13

CR 3-15

CR 3-17

CR 3-19

CR 3-21

CR 3-23

CR 3-25

Ph.

Oval*

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

11.97 (305)
11.97 (305)
11.97 (305)
11.97 (305)
12.68 (323)
12.68 (323)
13.39 (341)
13.39 (341)
14.09 (358)
14.09 (358)
14.80 (376)
14.80 (376)
15.51 (394)
15.51 (394)
16.22 (412)
16.22 (412)
16.93 (431)
16.93 (431)
17.64 (449)
17.64 (449)
18.35 (467)
18.35 (467)
20.16 (513)
20.16 (513)
21.57 (548)
21.57 (548)
22.99 (584)
22.99 (584)
24.41 (621)
24.41 (621)
25.83 (657)
25.83 (657)
27.24 (692)
27.24 (692)
28.66 (728)
28.66 (728)

D1

D2

B1+B2

6.19 (158)
5.55 (141)
6.19 (158)
5.55 (141)
6.19 (158)
5.55 (141)
6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)

21.26 (541)
19.41 (494)
21.26 (541)
19.41 (494)
22.59 (574)
20.12 (512)
23.30 (592)
20.83 (530)
25.28 (643)
21.53 (547)
26.48 (673)
23.42 (595)
27.19 (691)
24.13 (613)
27.90 (709)
24.84 (631)
29.49 (750)
28.15 (716)
30.20 (768)
28.86 (734)
30.91 (786)
29.57 (752)
34.81 (885)
33.39 (849)
36.22 (920)
34.80 (884)
37.64 (957)
36.22 (920)
39.93 (1015)
39.92 (1014)
41.35 (1051)
41.34 (1051)
42.76 (1087)
42.75 (1086)
44.18 (1123)
44.17 (1122)

69 (32)
67 (31)
73 (34)
67 (31)
78 (36)
69 (32)
79 (36)
70 (32)
91 (42)
71 (33)
95 (44)
72 (33)
96 (44)
73 (34)
97 (44)
74 (34)
109 (50)
96 (44)
110 (50)
101 (46)
111 (51)
102 (47)
147 (67)
118 (54)
149 (68)
120 (55)
150 (69)
121 (55)
179 (82)
175 (80)
181 (83)
177 (81)
182 (83)
179 (82)
184 (84)
181 (83)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

43

10

Technical data

CR, CRI, CRN

Technical data

CRI 3
D2

D2
D1

B2

B2

D1

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

3/4 x 1 1/16"
1/2"

3 1/2"
4 1/8"

DRAIN
PLUG (G 1/2)

M10 x 40

3 15/16"
5 15/16"

3"
7 1/16"
8 5/16"

8 5/16"

3"
3 15/16"
5 15/16"
9 7/8"

1 3/8"

13/16"

2"

TM03 1452 2205

4 x 1/2"

TM03 1453 2205

5 1/2"

DRAIN
PLUG (G 1/2)

B1

1"NPT (F)
SUCTION AND
DISCHARGE

1 11/16"

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

Oval*
D1

CRI 3-2

1/3

CRI 3-3

1/2

CRI 3-4

3/4

CRI 3-5

3/4

CRI 3-6

CRI 3-7

1 1/2

CRI 3-8

1 1/2

CRI 3-9

1 1/2

CRI 3-10

CRI 3-11

CRI 3-12

CRI 3-13

CRI 3-15

CRI 3-17

CRI 3-19

CRI 3-21

CRI 3-23

CRI 3-25

Ship. wt.
[lbs (kg)]

TEFC
B1
D2

B1+B2

1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
12.09
12.09
12.80
12.80
13.50
13.50
14.21
14.21
14.92
14.92
15.63
15.63

(308)
(308)
(308)
(308)
(326)
(326)
(343)
(343)
(361)
(361)
(379)
(379)
(398)
(398)

6.19
5.55
6.19
5.55
6.19
5.55
6.19
5.55
7.19
5.55
7.19
5.55
7.19
5.55

(158)
(141)
(158)
(141)
(158)
(141)
(158)
(141)
(183)
(141)
(183)
(141)
(183)
(141)

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)

21.38
19.53
21.38
19.53
22.71
20.24
23.41
20.94
25.40
21.65
26.60
23.54
27.31
24.25

(544)
(497)
(544)
(497)
(577)
(515)
(595)
(532)
(646)
(550)
(676)
(598)
(694)
(616)

64
62
67
62
73
63
74
65
86
65
90
67
91
68

1
3
1
3
1

16.34
16.34
17.05
17.05
17.76

(416)
(416)
(434)
(434)
(452)

7.19
5.55
7.19
7.01
7.19

(183)
(141)
(183)
(179)
(183)

5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)

28.02
24.96
29.61
28.27
30.32

(712)
(634)
(753)
(719)
(771)

92 (42)
69 (32)
104 (48)
91 (42)
105 (48)

3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

17.76 (452)
18.46 (469)
18.46 (469)
20.28 (516)
20.28 (516)
21.69 (551)
21.69 (551)
23.11 (587)
23.11 (587)
24.53 (624)
24.53 (624)
25.94 (659)
25.94 (659)
27.36 (695)
27.36 (695)
28.78 (732)
28.78 (732)

7.01 (179)
7.19 (183)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)

4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)

28.98 (737)
31.02 (788)
29.68 (754)
34.93 (888)
33.51 (852)
36.34 (924)
34.92 (887)
37.76 (960)
36.34 (924)
40.05 (1018)
40.04 (1018)
41.46 (1054)
41.45 (1053)
42.88 (1090)
42.87 (1089)
44.30 (1126)
44.29 (1125)

95 (44)
106 (49)
96 (44)
140 (64)
111 (51)
142 (65)
113 (52)
143 (65)
114 (52)
172 (79)
168 (77)
174 (79)
170 (78)
175 (80)
172 (79)
177 (81)
174 (79)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

44

(30)
(29)
(31)
(29)
(34)
(29)
(34)
(30)
(40)
(30)
(41)
(31)
(42)
(31)

Technical data

10
Technical data

CR, CRI, CRN

CRN 3
D2

D2

D1

B2

B2

D1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

3/4 x 1 1/16"
1/2"

7 1/16"
8 5/16"

8 1/4"

3"
3 15/16"
5 15/16"
9 7/8"

1 3/8"

3 15/16"
5 15/16"

13/16"

2"

TM03 1454 2205

4 x 1/2"

4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

TM03 1453 2205

DRAIN
PLUG (G 1/2)

3 1/2"
4 1/8"

1 1/4" Victaulic-type
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

5 1/2"

B1

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRN 3-2

1/3

CRN 3-3

1/2

CRN 3-4

3/4

CRN 3-5

3/4

CRN 3-6

CRN 3-7

1 1/2

CRN 3-8

1 1/2

CRN 3-9

1 1/2

CRN 3-10

CRN 3-11

CRN 3-12

CRN 3-13

CRN 3-15

CRN 3-17

CRN 3-19

CRN 3-21

CRN 3-23

CRN 3-25

Ph.

PJE*

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09 (308)
12.09 (308)
12.09 (308)
12.09 (308)
12.80 (326)
12.80 (326)
13.50 (343)
13.50 (343)
14.21 (361)
14.21 (361)
14.92 (379)
14.92 (379)
15.63 (398)
15.63 (398)
16.34 (416)
16.34 (416)
17.05 (434)
17.05 (434)
17.76 (452)
17.76 (452)
18.46 (469)
18.46 (469)
20.28 (516)
20.28 (516)
21.69 (551)
21.69 (551)
23.11 (587)
23.11 (587)
24.53 (624)
24.53 (624)
25.94 (659)
25.94 (659)
27.36 (695)
27.36 (695)
28.78 (732)
28.78 (732)

D1

D2

B1+B2

6.19 (158)
5.55 (141)
6.19 (158)
5.55 (141)
6.19 (158)
5.55 (141)
6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)

5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)

21.38 (544)
19.53 (497)
21.38 (544)
19.53 (497)
22.71 (577)
20.24 (515)
23.41 (595)
20.94 (532)
25.40 (646)
21.65 (550)
26.60 (676)
23.54 (598)
27.31 (694)
24.25 (616)
28.02 (712)
24.96 (634)
29.61 (753)
28.27 (719)
30.32 (771)
28.98 (737)
31.02 (788)
29.68 (754)
34.93 (888)
33.51 (852)
36.34 (924)
34.92 (887)
37.76 (960)
36.34 (924)
40.05 (1018)
40.04 (1018)
41.46 (1054)
41.45 (1053)
42.88 (1090)
42.87 (1089)
44.30 (1126)
44.29 (1125)

64 (30)
62 (29)
67 (31)
62 (29)
73 (34)
63 (29)
73 (34)
64 (30)
86 (40)
65 (30)
90 (41)
67 (31)
91 (42)
68 (31)
92 (42)
69 (32)
104 (48)
91 (42)
105 (48)
95 (44)
106 (49)
96 (44)
139 (64)
110 (50)
142 (65)
112 (51)
143 (65)
114 (52)
172 (79)
168 (77)
174 (79)
170 (78)
175 (80)
171 (78)
177 (81)
173 (79)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

45

10

Technical data

CR, CRI, CRN

Technical data

CR 5
D2

D2

D1

PRIMING
PORT (G 1/2)

B1

B1

1 1/4"250 lb.R.F.
SUCTION AND
DISCHARGE

1 1/4"NPT (F)
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

7/8"

5 1/2"

3"
3 15/16"
5 9/16"
9 7/8"

13/16"

4 x 1/2"
3"
7 1/16"
8 11/16"

TM03 1455 2205

13/16"

5 11/16"
6 5/16"

3/4"x1"

M10 x 40

2"

3 15/16"

DRAIN
PLUG (G 1/2)

4 x 1/2"
1 3/8"
7 1/16"
8 11/16"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CR 5-2

3/4

CR 5-3

CR 5-4

1 1/2

CR 5-5

CR 5-6

CR 5-7

CR 5-8

CR 5-9

CR 5-10

CR 5-11

CR 5-12

CR 5-13

CR 5-14

CR 5-15

CR 5-16

CR 5-18

7 1/2

CR 5-20

7 1/2

CR 5-22

7 1/2

CR 5-24

7 1/2

Ph.

Oval*

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

11.97 (305)
11.97 (305)
13.03 (331)
13.03 (331)
14.09 (358)
14.09 (358)
15.16 (386)
15.16 (386)
16.22 (412)
16.22 (412)
18.39 (468)
18.39 (468)
19.45 (495)
19.45 (495)
20.51 (521)
20.51 (521)
21.57 (548)
21.57 (548)
22.64 (576)
22.64 (576)
23.7 (602)
23.7 (602)
24.76 (629)
24.76 (629)
25.83 (657)
25.83 (657)
26.89 (684)
26.89 (684)
27.95 (710)
27.95 (710)
30.59 (777)
30.59 (777)
32.72 (832)
32.72 (832)
34.84 (885)
34.84 (885)
36.97 (940)
36.97 (940)

D1

D2

B1+B2

6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)

5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)

21.88 (556)
19.41 (494)
24.22 (616)
20.47 (520)
25.77 (655)
22.71 (577)
27.72 (705)
26.38 (671)
28.78 (732)
27.44 (697)
33.04 (840)
31.62 (804)
34.10 (867)
32.68 (831)
35.16 (894)
33.74 (857)
37.09 (943)
37.08 (942)
38.16 (970)
38.15 (970)
39.22 (997)
39.21 (996)
40.28 (1024)
40.27 (1023)
41.35 (1051)
41.34 (1051)
42.41 (1078)
42.40 (1077)
43.47 (1105)
43.46 (1104)
46.12 (1172)
46.19 (1171)
48.25 (1226)
48.23 (1226)
50.37 (1280)
50.35 (1279)
52.50 (1334)
52.48 (1333)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pumps and weight is approximately 9 lbs. less.
Available.

46

77 (35)
68 (31)
90 (41)
69 (32)
94 (43)
71 (33)
106 (49)
93 (43)
108 (49)
95 (44)
143 (65)
114 (52)
145 (66)
116 (53)
147 (67)
118 (54)
170 (78)
168 (77)
172 (79)
169 (77)
177 (81)
170 (78)
178 (81)
171 (78)
180 (82)
176 (80)
181 (83)
177 (81)
182 (83)
178 (81)
200 (91)
188 (86)
203 (93)
190 (87)
300 (137)
287 (131)
302 (137)
290 (132)

TM03 1451 2205

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

3 1/2"
3 15/16"

B2

B2

D1

Technical data

10
Technical data

CR, CRI, CRN

CRI 5
D2

D2

D1

B2

B2

D1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

8 5/16"

5 1/2"

TM03 1456 2205

3 15/16"
5 15/16"
9 7/8"

1 3/8"

13/16"

2"

3"
7 1/16"
8 5/16"

4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

TM03 1453 2205

3 1/2"
4 1/8"

3/4 x 1 1/16"
1/2"

M10 x 60
4 x 1/2"

3 15/16"
5 15/16"

DRAIN
PLUG (G 1/2)

3"

DRAIN
PLUG (G 1/2)

B1

1 1/4"NPT (F)
SUCTION AND
DISCHARGE

1 11/16"

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRI 5-2

3/4

CRI 5-3

CRI 5-4

1 1/2

CRI 5-5

CRI 5-6

CRI 5-7

CRI 5-8

CRI 5-9

CRI 5-10

CRI 5-11

CRI 5-12

CRI 5-13

CRI 5-14

CRI 5-15

CRI 5-16

CRI 5-18

7 1/2

CRI 5-20

7 1/2

CRI 5-22

7 1/2

CRI 5-24

7 1/2

Ph.

Oval*

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
13.15
13.15
14.21
14.21
15.28
15.28
16.34
16.34
18.51
18.51
19.57
19.57
20.63
20.63
21.69
21.69
22.76
22.76
23.82
23.82
24.88
24.88
25.94
25.94
27.01
27.01
28.07
28.07
30.71
30.71
32.83
32.83
34.96
34.96
37.09
37.09

(308)
(308)
(335)
(335)
(361)
(361)
(389)
(389)
(416)
(416)
(471)
(471)
(498)
(498)
(525)
(525)
(551)
(551)
(579)
(579)
(606)
(606)
(632)
(632)
(659)
(659)
(687)
(687)
(713)
(713)
(781)
(781)
(834)
(834)
(888)
(888)
(943)
(943)

D1

D2

B1+B2

6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)

5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)

22.00 (559)
19.53 (497)
24.34 (619)
20.59 (523)
25.89 (658)
22.83 (580)
27.84 (708)
26.50 (674)
28.90 (735)
27.56 (701)
33.16 (843)
31.74 (807)
34.22 (870)
32.80 (834)
35.28 (897)
33.86 (861)
37.21 (946)
37.20 (945)
38.28 (973)
38.27 (973)
39.34 (1000)
39.33 (999)
40.40 (1027)
40.39 (1026)
41.46 (1054)
41.45 (1053)
42.53 (1081)
42.52 (1081)
43.59 (1108)
43.58 (1107)
46.24 (1175)
46.22 (1174)
48.36 (1229)
48.34 (1228)
50.49 (1283)
50.47 (1282)
52.62 (1337)
52.60 (1337)

71 (33)
62 (29)
85 (39)
64 (30)
89 (41)
66 (30)
101 (46)
88 (40)
103 (47)
90 (41)
136 (62)
107 (49)
138 (63)
109 (50)
140 (64)
111 (51)
163 (74)
160 (73)
165 (75)
162 (74)
170 (78)
163 (74)
171 (78)
164 (75)
173 (79)
169 (77)
174 (79)
170 (78)
175 (80)
171 (78)
193 (88)
181 (83)
196 (89)
183 (84)
293 (133)
280 (128)
295 (134)
283 (129)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pumps and weight is approximately 9 lbs. less.
Available.

47

10

Technical data

CR, CRI, CRN

Technical data

CRN 5
D2

D2

D1

B2

B2

D1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

3/4 x 1 1/16"
1/2"

7 1/16"
8 5/16"

8 1/4"

3 15/16"
5 15/16"
9 7/8"

1 3/8"

TM03 1454 2205

13/16"

2"
3 15/16"
5 15/16"

3"

4 x 1/2"

4 x 1/2"
1 1/4"
3 3/8"
7 1/16
8 1/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRN 5-2

3/4

CRN 5-3

CRN 5-4

1 1/2

CRN 5-5

CRN 5-6

CRN 5-7

CRN 5-8

CRN 5-9

CRN 5-10

CRN 5-11

CRN 5-12

CRN 5-13

CRN 5-14

CRN 5-15

CRN 5-16

CRN 5-18

7 1/2

CRN 5-20

7 1/2

CRN 5-22

7 1/2

CRN 5-24

7 1/2

Ph.

PJE*

Ship. wt.
[lbs (kg)]

TEFC
B1

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3

12.09
12.09
13.15
13.15
14.21
14.21
15.28
15.28
16.34
16.34
18.51
18.51
19.57
19.57
20.63
20.63
21.69
21.69
22.76
22.76
23.82
23.82
24.88
24.88
25.94
25.94
27.01
27.01
28.07
28.07
30.71
30.71
32.83
32.83
34.96
34.96
37.09
37.09

(308)
(308)
(335)
(335)
(361)
(361)
(389)
(389)
(416)
(416)
(471)
(471)
(498)
(498)
(525)
(525)
(551)
(551)
(579)
(579)
(606)
(606)
(632)
(632)
(659)
(659)
(687)
(687)
(713)
(713)
(781)
(781)
(834)
(834)
(888)
(888)
(943)
(943)

D1

D2

B1+B2

6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
5.55 (141)
7.19 (183)
7.01 (179)
7.19 (183)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)

5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.57 (117)
5.73 (146)
4.33 (110)
5.73 (146)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)

22.00 (559)
19.53 (497)
24.34 (619)
20.59 (523)
25.89 (658)
22.83 (580)
27.84 (708)
26.5 (674)
28.90 (735)
27.56 (701)
33.16 (843)
31.74 (807)
34.22 (870)
32.80 (834)
35.28 (897)
33.86 (861)
37.21 (946)
37.20 (945)
38.28 (973)
38.27 (973)
39.34 (1000)
39.33 (999)
40.40 (1027)
40.39 (1026)
41.46 (1054)
41.45 (1053)
42.53 (1081)
42.52 (1081)
43.59 (1108)
43.58 (1107)
46.24 (1175)
46.22 (1174)
48.36 (1229)
48.34 (1228)
50.49 (1283)
50.47 (1282)
52.62 (1337)
52.60 (1337)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is one inch less than ANSI flanged pumps and weight is approximately 9 lbs. less.
Available.

48

71 (33)
62 (29)
85 (39)
64 (30)
89 (41)
65 (30)
101 (46)
88 (40)
103 (47)
90 (41)
136 (62)
107 (49)
138 (63)
109 (50)
139 (64)
110 (50)
163 (74)
160 (73)
165 (75)
161 (74)
170 (78)
163 (74)
171 (78)
164 (75)
172 (79)
169 (77)
173 (79)
170 (78)
175 (80)
171 (78)
193 (88)
180 (82)
196 (89)
183 (84)
292 (133)
279 (127)
295 (134)
282 (128)

TM03 1453 2205

DRAIN
PLUG (G 1/2)

3 1/2"
4 1/8"

1 1/4" Victaulic-type
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

5 1/2"

B1

B1

1 1/4"300 lb.R.F.
SUCTION AND
DISCHARGE

Technical data

10
Technical data

CR, CRI, CRN

CR 10
D2

D2

D1

5 1/8"
8 1/2"
10 1/8"

5 1/8"
6 15/16"
11 7/8"

4 3/4"
8 1/2"
10 1/8"

4 x 9/16"

TM03 1461 2205

TM03 1460 2205

13/16"

5 1/8"
7"
7 7/8"

3/4 x 7/8"

3 1/2"

4 x 9/16"

DRAIN
PLUG (G 1/2)

5"

B1

M10 x 40

2" ANSI 250 lb.


R.F.

13/16"

1 3/16"

3 1/2"

B1

2" NPT
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

6 1/2"

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

2 9/16"

B2

B2

D1

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CR 10-1

3/4

CR 10-2

1 1/2

CR 10-3

CR 10-4

CR 10-5

CR 10-6

CR 10-7

7 1/2

CR 10-8

7 1/2

CR 10-9

7 1/2

CR 10-10

7 1/2

CR 10-12

10

CR 10-14
CR 10-16
CR 10-17

15
15
15

Ph.

Oval*

TEFC

Ship. wt.
[lbs (kg)]

ODP

B1
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
3
3
3

15.28
15.28
15.28
15.28
17.20
17.20
18.39
18.39
19.57
19.57
20.75
20.75
22.25
22.25
23.43
23.43
24.61
24.61
25.79
25.79
28.15
28.15
33.06
35.43
37.80

(389)
(389)
(389)
(389)
(437)
(437)
(468)
(468)
(498)
(498)
(528)
(528)
(566)
(566)
(596)
(596)
(626)
(626)
(656)
(656)
(716)
(716)
(840)
(900)
(961)

D1

D2

B1+B2

D1

D2

B1+B2

6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)

5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)

25.19 (640)
22.72 (578)
26.96 (685)
23.90 (608)
31.85 (809)
30.43 (773)
33.04 (840)
31.62 (804)
35.09 (892)
35.08 (892)
36.27 (922)
36.26 (922)
37.78 (960)
37.76 (960)
38.96 (990)
38.94 (990)
40.14 (1020)
40.12 (1020)
41.32 (1050)
41.30 (1050)
44.22 (1124)
42.88 (1090)
51.60 (1311)
53.97 (1371)
56.34 (1432)

10.62 (270)
10.62 (270)
10.62 (270)

7.33 (187)
7.33 (187)
7.33 (187)

49.37 (1254)
51.74 (1315)
54.11 (1375)

115 (53)
106 (49)
128 (59)
106 (49)
183 (84)
153 (70)
183 (84)
156 (71)
209 (95)
206 (94)
212 (97)
208 (95)
232 (106)
221 (101)
234 (107)
223 (102)
236 (108)
225 (103)
238 (108)
227 (103)
355 (162)
232 (106)
414 (188)
422 (192)
426 (194)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 3 lbs. less.
Available.

49

10

Technical data

CR, CRI, CRN

Technical data

CRI 10
D2

D2
D1

B2

B2

D1

2" ANSI 300 lb.


R.F.

DRAIN
PLUG (G 1/2)

3/4 x 7/8"

9 3/4"

3 1/2"

7 7/8"
11 7/8"

4 x 9/16"
2 9/16"
4 3/4"
8 1/2"
9 3/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRI 10-1

CRI 10-2

1 1/2

CRI 10-3

CRI 10-4

CRI 10-5

CRI 10-6

CRI 10-7

7 1/2

CRI 10-8

7 1/2

CRI 10-9

7 1/2

CRI 10-10

7 1/2

CRI 10-12

10

CRI 10-14
CRI 10-16
CRI 10-17

15
15
15

Ph.

Oval*

TEFC

1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
3
3
3

15.20
15.20
15.20
15.20
17.13
17.13
18.31
18.31
19.49
19.49
20.67
20.67
22.17
22.17
23.35
23.35
24.53
24.53
25.71
25.71
28.07
28.07
32.95
35.31
37.68

(387)
(387)
(387)
(387)
(436)
(436)
(466)
(466)
(496)
(496)
(526)
(526)
(564)
(564)
(594)
(594)
(624)
(624)
(654)
(654)
(713)
(713)
(837)
(897)
(958)

D1

D2

B1+B2

D1

D2

B1+B2

6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)

5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (762)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)

25.11 (638)
22.64 (576)
26.88 (683)
23.82 (606)
31.78 (808)
30.36 (772)
32.96 (838)
31.54 (802)
35.01 (890)
35.00 (889)
36.19 (920)
36.18 (919)
37.70 (958)
37.68 (958)
38.88 (988)
38.86 (988)
40.06 (1018)
40.04 (1018)
41.24 (1048)
41.22 (1047)
44.14 (1122)
42.80 (1088)
51.49 (1308)
53.85 (1368)
56.22 (1428)

10.62 (270)
10.62 (270)
10.62 (270)

7.33 (187)
7.33 (187)
7.33 (187)

49.26 (1252)
51.62 (1312)
53.99 (1372)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 7 lbs. less.
Available.

50

Ship. wt.
[lbs (kg)]

ODP

B1

106 (49)
98 (45)
122 (56)
100 (46)
175 (80)
147 (67)
177 (81)
147 (67)
203 (93)
199 (91)
206 (94)
202 (92)
225 (103)
212 (97)
228 (103)
214 (98)
230 (105)
217 (99)
232 (106)
219 (100)
347 (158)
225 (103)
403 (183)
413 (188)
418 (190)

TM03 1459 2205

8 1/2"

5 1/8"

1 1/16"

1 1/16"

3 15/16"

TM03 1458 2205

4 x 9/16"

5 1/8"
7 7/8"
10 1/8"

5"

M12x80

6 1/2"

B1

2" NPT
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 1/2"

B1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

Technical data

10
Technical data

CR, CRI, CRN

CRN 10
D2

D2

D1

B2

B2

D1

DRAIN
PLUG (G 1/2)

7 7/8"
11 7/8"

4 x 9/16"
2 9/16"
4 3/4"
8 1/2"
9 3/4"

TM03 1459 2205

5"
5 1/8"

1 1/16"

TM03 1457 2205

8 1/2"
9 3/4"

3/4 x 7/8"

3 1/2"

1 1/16"

4 x 9/16"

5 1/8"
7 7/8"
10 1/4"

2" ANSI 300 lb.


R.F.

6 1/2"

B1

2" Victaulic-type
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 1/2"

B1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRN 10-1

3/4

CRN 10-2

1 1/2

CRN 10-3

CRN 10-4

CRN 10-5

CRN 10-6

CRN 10-7

7 1/2

CRN 10-8

7 1/2

CRN 10-9

7 1/2

CRN 10-10

7 1/2

CRN 10-12

10

CRN 10-14
CRN 10-16
CRN 10-17

15
15
15

Ph.

PJE*

TEFC

Ship. wt.
[lbs (kg)]

ODP

B1
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
3
3
3

15.20
15.20
15.20
15.20
17.13
17.13
18.31
18.31
19.49
19.49
20.67
20.67
22.17
22.17
23.35
23.35
24.53
24.53
25.71
25.71
28.07
28.07
32.95
35.31
37.68

(387)
(387)
(387)
(387)
(436)
(436)
(466)
(466)
(496)
(496)
(526)
(526)
(564)
(564)
(594)
(594)
(624)
(624)
(654)
(654)
(713)
(713)
(837)
(897)
(958)

D1

D2

B1+B2

D1

D2

B1+B2

6.19 (158)
5.55 (141)
7.19 (183)
5.55 (141)
8.60 (219)
7.01 (179)
8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)

5.18 (132)
4.57 (117)
5.73 (146)
4.57 (117)
6.87 (175)
4.33 (110)
6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)

25.11 (638)
22.64 (576)
26.88 (683)
23.82 (606)
31.78 (808)
30.36 (772)
32.96 (838)
31.54 (802)
35.01 (890)
35.00 (889)
36.19 (920)
36.18 (919)
37.7 (958)
37.68 (958)
38.88 (988)
38.86 (988)
40.06 (1018)
40.04 (1018)
41.24 (1048)
41.22 (1047)
44.14 (1122)
42.80 (1088)
51.49 (1308)
53.85 (1368)
56.22 (1428)

10.62 (270)
10.62 (270)
10.62 (270)

7.33 (187)
7.33 (187)
7.33 (187)

49.25 (1251)
51.63 (1312)
54.00 (1372)

106 (49)
97 (44)
121 (55)
99 (45)
176 (80)
147 (67)
176 (80)
149 (68)
203 (93)
199 (91)
205 (93)
201 (92)
227 (103)
214 (98)
229 (104)
216 (98)
232 (106)
218 (99)
234 (107)
221 (101)
346 (157)
225 (103)
403 (183)
413 (188)
418 (190)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 9 lbs. less.
Available.

51

10

Technical data

CR, CRI, CRN

Technical data

CR 15
D2

D2

D1

3/4 x 7/8"

5"
5 1/8"
6 15/16"
11 7/8"

13/16"

3 1/2"

TM03 1460 2205

13/16"

5 1/8"
8 1/2"
10 1/8"

4 3/4"
8 1/2"
10 1/8"

4 x 9/16"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CR 15-1

CR 15-2

CR 15-3

7 1/2

CR 15-4

7 1/2

CR 15-5

10

CR
CR
CR
CR
CR
CR

15
15
15
20
20
25

15-6
15-7
15-8
15-9
15-10
15-12

Ph.

Oval*

TEFC

1
3
1
3
1
3
1
3
1
3
3
3
3
3
3
3

16.46
16.46
17.20
17.20
19.29
19.29
21.06
21.06
22.83
22.83
27.17
28.94
30.71
32.48
34.25
37.17

(419)
(419)
(437)
(437)
(490)
(490)
(535)
(535)
(580)
(580)
(691)
(736)
(781)
(825)
(870)
(945)

D1

D2

B1+B2

D1

D2

B1+B2

7.19 (183)
7.01 (179)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)

5.73 (146)
4.33 (110)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)

29.02 (738)
27.68 (704)
32.72 (832)
32.71 (831)
34.82 (885)
34.80 (884)
36.59 (930)
36.57 (929)
38.90 (989)
37.56 (955)
45.71 (1162)
47.48 (1206)
49.25 (1251)
51.02 (1296)
52.79 (1341)
59.56 (1513)

10.62 (270)
10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)

7.33 (187)
7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)

43.48 (1105)
45.25 (1150)
47.02 (1195)
52.17 (1326)
53.94 (1371)
57.98 (1473)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 3 lbs. less.
Available.

52

Ship. wt.
[lbs (kg)]

ODP

B1

139 (64)
128 (59)
205 (93)
201 (92)
223 (102)
212 (97)
225 (103)
214 (98)
342 (156)
218 (99)
347 (158)
378 (172)
409 (186)
417 (190)
421 (191)
422 (192)

TM03 1461 2205

B1

DRAIN
PLUG (G 1/2)

M10 x 40
4 x 9/16"

5 1/8"
7"
7 7/8"

2" ANSI 300 lb.


R.F.

6 1/2"

1 3/16"

3 1/2"

B1

2" NPT
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

2 9/16"

B2

B2

D1

Technical data

10
Technical data

CR, CRI, CRN

CRI 15
D2
D1

D2

B2

B2

D1

5"

4 x 9/16"
2 9/16"
4 3/4"
8 1/2"
9 3/4"

TM03 1459 2205

9 3/4"

5 1/8"
7 7/8"
11 7/8"

1 1/16"

1 1/16"

8 1/2"

TM03 1458 2205

4 x 9/16"

3 15/16"

3/4 x 7/8"

3 1/2"

M12x80

DRAIN
PLUG (G 1/2)

6 1/2"

2" NPT
SUCTION AND
DISCHARGE

3 1/2"

B1

B1

2" ANSI 300 lb.


R.F.

DRAIN
PLUG (G 1/2)

5 1/8"
7 7/8"
10 1/8"

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRI 15-1

CRI 15-2

CRI 15-3

7 1/2

CRI 15-4

7 1/2

CRI 15-5

10

CRI
CRI
CRI
CRI
CRI
CRI

15
15
15
20
20
25

15-6
15-7
15-8
15-9
15-10
15-12

Ph.

Oval*

TEFC

Ship. wt.
[lbs (kg)]

ODP

B1
1
3
1
3
1
3
1
3
1
3
3
3
3
3
3
3

16.38
16.38
17.13
17.13
19.21
19.21
20.98
20.98
22.76
22.76
27.05
28.82
30.59
32.36
34.13
37.05

(417)
(417)
(436)
(436)
(488)
(488)
(533)
(533)
(579)
(579)
(688)
(733)
(777)
(822)
(867)
(942)

D1

D2

B1+B2

D1

D2

B1+B2

7.19 (183)
7.01 (179)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)

5.73 (146)
4.33 (110)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)

28.94 (736)
27.60 (702)
32.65 (830)
32.64 (830)
34.74 (883)
34.72 (882)
36.51 (928)
36.49 (927)
38.83 (987)
37.49 (953)
45.59 (1158)
47.36 (1203)
49.13 (1248)
50.90 (1293)
52.67 (1338)
59.44 (1510)

10.62 (270)
10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)

7.33 (187)
7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)

43.36 (1102)
45.13 (1147)
46.90 (1192)
52.05 (1323)
53.82 (1368)
57.86 (1470)

130 (59)
121 (55)
198 (90)
195 (89)
216 (98)
203 (93)
218 (99)
205 (93)
333 (152)
212 (97)
336 (153)
369 (168)
402 (183)
410 (186)
413 (188)
413 (188)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 7 lbs. less.
Available.

53

10

Technical data

CR, CRI, CRN

Technical data

CRN 15
D2

D2

D1

B2

B2

D1

DRAIN
PLUG (G 1/2)

4 x 9/16"
2 9/16"
4 3/4"
8 1/2"
9 3/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRN 15-1

CRN 15-2

CRN 15-3

7 1/2

CRN 15-4

7 1/2

CRN 15-5

10

CRN
CRN
CRN
CRN
CRN
CRN

15
15
15
20
20
25

15-6
15-7
15-8
15-9
15-10
15-12

Ph.

PJE*

TEFC

1
3
1
3
1
3
1
3
1
3
3
3
3
3
3
3

16.38
16.38
17.44
17.13
19.21
19.21
20.98
20.98
22.76
22.76
27.05
28.82
30.59
32.36
34.13
37.05

(417)
(417)
(443)
(436)
(488)
(488)
(533)
(533)
(579)
(579)
(688)
(733)
(777)
(822)
(867)
(942)

D1

D2

B1+B2

D1

D2

B1+B2

7.19 (183)
7.01 (179)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)

5.73 (146)
4.33 (110)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)

28.94 (736)
27.6 (702)
32.96 (838)
32.64 (830)
34.74 (883)
34.72 (882)
36.51 (928)
36.49 (927)
38.83 (987)
37.49 (953)
45.59 (1158)
47.36 (1203)
49.13 (1248)
50.90 (1293)
52.67 (1338)
59.44 (1510)

10.62 (270)
10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)

7.33 (187)
7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)

43.36 (1102)
45.13 (1147)
46.90 (1192)
52.05 (1323)
53.82 (1368)
57.86 (1470)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pump and weight is approximately 9 lbs. less.
Available.

54

Ship. wt.
[lbs (kg)]

ODP

B1

130 (59)
121 (55)
203 (93)
195 (89)
216 (98)
205 (93)
218 (99)
207 (94)
335 (152)
214 (98)
336 (153)
369 (168)
402 (183)
410 (186)
413 (188)
413 (188)

TM03 1459 2205

5"
5 1/8"
7 7/8"
11 7/8"

1 1/16"

TM03 1457 2205

8 1/2"
9 3/4"

3/4 x 7/8"

3 1/2"

1 1/16"

4 x 9/16"

5 1/8"
7 7/8"
10 1/4"

2" ANSI 300 lb.


R.F.

6 1/2"

B1

2" Victaulic-type
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 1/2"

B1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

Technical data

10
Technical data

CR, CRI, CRN

CR 20
D2

D2
D1

B2

B2

D1

5 1/8"
8 1/2"
10 1/8"

5 1/8"
6 15/16"
11 7/8"

4 3/4"
8 1/2"
10 1/8"

6 1/2"

4 x 9/16"

TM03 1461 2205

TM03 1460 2205

13/16"

5 1/8"
7"
7 7/8"

3/4 x 7/8"

3 1/2"

4 x 9/16"

DRAIN
PLUG (G 1/2)

5"

B1

M10 x 40

2" ANSI 250 lb.


R.F.

13/16"

1 3/16"

3 1/2"

B1

2" NPT
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

2 9/16"

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CR 20-1

CR 20-2

CR 20-3

7 1/2

CR 20-4

10

CR
CR
CR
CR
CR

15
15
20
20
25

20-5
20-6
20-7
20-8
20-10

Ph.

TEFC
Oval*

Ship. wt.
[lbs (kg)]

ODP

B1
D1

D2

1
3
1
3
1
3

17.20
17.20
17.20
17.20
19.29
19.29

(437)
(437)
(437)
(437)
(490)
(490)

8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)

6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)

31.85
30.43
32.72
32.71
34.82
34.80

1
3
3
3
3
3
3

21.06
21.06
25.39
27.17
28.94
30.71
33.62

(535)
(535)
(645)
(691)
(736)
(781)
(854)

10.23
10.24
12.36
12.36
12.36
12.36
12.36

10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)

37.13 (944)
35.79 (910)
43.93 (1116)
45.71 (1162)
47.48 (1206)
49.25 (1251)
56.01 (1423)

(260)
(261)
(314)
(314)
(314)
(314)
(314)

B1+B2
(809)
(773)
(832)
(831)
(885)
(884)

D1

D2

B1+B2

181 (83)
151 (69)
205 (93)
201 (92)
223 (102)
209 (95)

10.62 (270)
10.62 (270)
11.5 (293)
11.5 (293)
11.5 (293)

7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)

41.70 (1060)
43.48 (1105)
48.63 (1236)
50.40 (1281)
54.43 (1383)

337 (153)
214 (98)
369 (168)
373 (170)
409 (186)
413 (188)
413 (188)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 3 lbs. less.
Available.

55

10

Technical data

CR, CRI, CRN

Technical data

CRI 20
D2

D2

D1

2" ANSI 300 lb.


R.F.

DRAIN
PLUG (G 1/2)

3/4 x 7/8"

9 3/4"

3 1/2"

5 1/8"
7 7/8"
11 7/8"

4 x 9/16"
2 9/16"
4 3/4"

1 1/16"

1 1/16"

3 15/16"
8 1/2"

TM03 1458 2205

4 x 9/16"

5 1/8"
7 7/8"
10 1/8"

5"

M12x80

8 1/2"
9 3/4"

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRI 20-1

CRI 20-2

CRI 20-3

7 1/2

CRI 20-4

10

CRI
CRI
CRI
CRI
CRI

15
15
20
20
25

20-5
20-6
20-7
20-8
20-10

Ph.

TEFC
Oval*

1
3
1
3
1
3
1
3
3
3
3
3
3

17.13
17.13
17.13
17.13
19.21
19.21
20.98
20.98
25.28
27.05
28.82
30.59
33.50

(436)
(436)
(436)
(436)
(488)
(488)
(533)
(533)
(643)
(688)
(733)
(777)
(851)

D1

D2

B1+B2

D1

D2

B1+B2

8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)

6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)

31.78 (808)
30.36 (772)
32.65 (830)
32.64 (830)
34.74 (883)
34.72 (882)
37.05 (942)
35.71 (908)
43.82 (1114)
45.59 (1158)
47.36 (1203)
49.13 (1248)
55.89 (1420)

10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)

7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)

41.59 (1057)
43.36 (1102)
48.51 (1233)
50.28 (1278)
54.31 (1380)

All dimensions in inches unless otherwise noted.


* Oval flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 7 lbs. less.
Available.

56

Ship. wt.
[lbs (kg)]

ODP

B1

174 (79)
145 (66)
198 (90)
195 (89)
216 (98)
203 (93)
331 (151)
205 (93)
362 (165)
367 (167)
402 (185)
406 (185)
407 (185)

TM03 1459 2205

B1

2" NPT
SUCTION AND
DISCHARGE

DRAIN
PLUG (G 1/2)

3 1/2"

B1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

6 1/2"

B2

B2

D1

Technical data

10
Technical data

CR, CRI, CRN

CRN 20
D2

D2

D1

B2

B2

D1

5"
5 1/8"
7 7/8"
11 7/8"

6 1/2"

3/4 x 7/8"

4 x 9/16"
2 9/16"
4 3/4"
8 1/2"
9 3/4"

TM03 1459 2205

TM03 1457 2205

8 1/2"
9 3/4"

5 1/8"
7 7/8"
10 1/4"

DRAIN
PLUG (G 1/2)

3 1/2"

4 x 9/16"

2" ANSI 300 lb.


R.F.

1 1/16"

1 1/16"

DRAIN
PLUG (G 1/2)

B1

2" Victaulic-type
SUCTION AND
DISCHARGE

3 1/2"

B1

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

PRIMING
PORT (G 1/2)

G 1/2 PLUG
WITH 1/4"TAP
FOR GAUGE/
SENSOR

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

CRN 20-1

CRN 20-2

CRN 20-3

7 1/2

CRN 20-4

10

CRN
CRN
CRN
CRN
CRN

15
15
20
20
25

20-5
20-6
20-7
20-8
20-10

Ph.

TEFC
PJE*

1
3
1
3
1
3
1
3
3
3
3
3
3

Ship. wt.
[lbs (kg)]

ODP

B1
17.13
17.13
17.13
17.13
19.21
19.21
20.98
20.98
25.28
27.05
28.82
30.59
33.50

(436)
(436)
(436)
(436)
(488)
(488)
(533)
(533)
(643)
(688)
(733)
(777)
(851)

D1

D2

B1+B2

D1

D2

B1+B2

8.60 (219)
7.01 (179)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)

6.87 (175)
4.33 (110)
7.46 (190)
5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)

31.78 (808)
30.36 (772)
32.65 (830)
32.64 (830)
34.74 (883)
34.72 (882)
37.05 (942)
35.71 (908)
43.82 (1114)
45.59 (1158)
47.36 (1203)
49.13 (1248)
55.89 (1420)

10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)

7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)

41.59 (1057)
43.36 (1102)
48.51 (1233)
50.28 (1278)
54.31 (1380)

174 (79)
145 (66)
198 (90)
195 (89)
216 (98)
203 (93)
331 (151)
207 (94)
365 (166)
367 (167)
402 (183)
406 (185)
407 (185)

All dimensions in inches unless otherwise noted.


* PJE flanged pump B1 and B1+B2 dimension is equal to ANSI flanged pumps and weight is approximately 9 lbs. less.
Available.

57

10

Technical data

CR, CRI, CRN

Technical data

TM02 7699 1009

CR 32

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

TEFC

Ph.
D1

CR 32-1-1

CR 32-1

CR 32-2-2

7 1/2

CR 32-2-1

7 1/2

20.08 (511)
19.88 (505)
20.08 (511)
19.88 (505)
22.83 (580)

10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)

7.46
5.28
7.46
5.28
7.62

22.64 (576)
22.83 (580)
22.64 (576)
22.83 (580)
22.64 (576)
25.59 (650)
25.39 (645)
29.72 (755)
32.48 (825)
32.48 (825)
35.24 (896)
35.24 (896)
37.99 (965)
37.99 (965)
40.75 (1036)
40.75 (1036)
43.50 (1105)
43.50 (1105)
46.26 (1176)
46.26 (1176)

8.66 (220)
10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
15.32 (390)
15.32 (390)
15.32 (390)

5.28 (135)
7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
13.11 (333)

49.02 (1246)
49.02 (1246)
51.77 (1315)

15.32 (390)
15.32 (390)
16.88 (429)

13.11 (333)
13.11 (333)
14.12 (359)

CR 32-2

10

CR 32-3-2

10

CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR

15
15
20
20
20
25
25
30
30
30
40
40
40
40
40
50

3
3
3

CR 32-10-2
CR 32-10
CR 32-11-2
1)

D2

1
3
1
3
1
3
1
3
1
3
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3

32-3
32-4-2
32-4
32-5-2
32-5
32-6-2
32-6
32-7-2
32-7
32-8-2
32-8
32-9-2
32-9

(190)
(135)
(190)
(135)
(194)

B1+B2

D1

D2

B1+B2

240 (109)
218 (99)
228 (104)
218 (99)
245 (112)

38.15 (970)
38.36 (975)
38.15 (970)
38.90 (989)
37.87 (962)
41.66 (1059)
40.12 (1020)
48.26 (1226)
51.02 (1296)
51.02 (1296)
53.78 (1367)
53.78 (1367)
60.38 (1534)
60.38 (1534)
63.14 (1604)
63.14 (1604)
65.89 (1674)
66.69 (1694)
69.45 (1765)
69.45 (1765)

10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)

7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.92 (227)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)

46.03 (1170)
48.79 (1240)
52.17 (1326)
54.93 (1396)
54.93 (1396)
58.80 (1494)
58.80 (1494)
62.56 (1590)
62.56 (1590)
65.31 (1659)
66.75 (1696)
69.51 (1766)
69.51 (1766)

229 (104)
245 (112)
229 (104)
300 (137)
229 (104)
295 (134)
236 (108)
332 (151)
339 (154)
344 (157)
351 (160)
351 (160)
351 (160)
351 (160)
444 (202)
423 (192)
436 (198)
631 (287)
637 (289)
637 (289)

72.21 (1835)
72.21 (1835)
79.58 (2022)

13.25 (337)
13.25 (337)
13.25 (337)

12.21 (311)
12.21 (311)
12.21 (311)

72.27 (1836)
72.27 (1836)
74.52 (1893)

645 (293)
645 (293)
671 (305)

35.60
35.39
35.60
35.39
38.36

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

58

Ship. wt.1)
[lbs (kg)]

ODP

B1
(905)
(899)
(905)
(899)
(975)

Technical data

10
Technical data

CR, CRI, CRN

TM02 7703 1009

CRN 32

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

TEFC
D1

CRN 32-1-1

CRN 32-1

CRN 32-2-2

7 1/2

CRN 32-2-1

7 1/2

CRN 32-2

10

CRN 32-3-2

10

CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN

15
15
20
20
20
25
25
30
30
30
40
40
40
40
40
50

32-3
32-4-2
32-4
32-5-2
32-5
32-6-2
32-6
32-7-2
32-7
32-8-2
32-8
32-9-2
32-9
32-10-2
32-10
32-11-2

Ship. wt.1)
[lbs (kg)]

ODP

B1
D2

1
3
1
3
1
3
1
3

20.08 (511)
19.88 (505)
20.08 (511)
19.88 (505)
22.83 (580)
22.64 (576)
22.83 (580)
22.64 (576)

10.62 (270)
8.66 (220)
10.62 (270)
8.66 (220)
10.22 (260)
8.66 (220)
10.22 (260)
8.66 (220)

7.46
5.28
7.46
5.28
7.62
5.28
7.62
5.28

1
3
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3

22.83 (580)
22.64 (576)
25.59 (650)
25.39 (645)
29.72 (755)
32.48 (825)
32.48 (825)
35.24 (896)
35.24 (896)
37.99 (965)
37.99 (965)
40.75 (1036)
40.75 (1036)
43.50 (1105)
43.50 (1105)
46.26 (1176)
46.26 (1176)
49.02 (1246)
49.02 (1246)
51.77 (1315)

10.23
10.24
10.23
10.24
12.36
12.36
12.36
12.36
12.36
12.36
12.36
12.36
12.36
12.36
15.32
15.32
15.32
15.32
15.32
16.88

10.30 (262)
6.26 (160)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
13.11 (333)
13.11 (333)
13.11 (333)
14.12 (359)

(260)
(261)
(260)
(261)
(314)
(314)
(314)
(314)
(314)
(314)
(314)
(314)
(314)
(314)
(390)
(390)
(390)
(390)
(390)
(429)

(190)
(135)
(190)
(135)
(194)
(135)
(194)
(135)

B1+B2
35.60
35.39
35.60
35.39
38.36
38.15
38.36
38.15

(905)
(899)
(905)
(899)
(975)
(970)
(975)
(970)

38.90 (989)
37.37 (950)
41.66 (1059)
40.12 (1020)
48.26 (1226)
51.02 (1296)
51.02 (1296)
53.78 (1367)
53.78 (1367)
60.38 (1534)
60.38 (1534)
63.14 (1604)
63.14 (1604)
65.89 (1674)
66.69 (1694)
69.45 (1765)
69.45 (1765)
72.21 (1835)
72.21 (1835)
79.58 (2022)

D1

D2

B1+B2

245 (112)
223 (102)
233 (106)
223 (102)
250 (114)
234 (107)
250 (114)
234 (107)

10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)

7.33 (187)
7.33 (187)
8.92 (227)
8.92 (227)
8.92 (227)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)

46.03 (1170)
48.79 (1240)
52.17 (1326)
54.93 (1396)
54.93 (1396)
58.80 (1494)
58.80 (1494)
62.56 (1590)
62.56 (1590)
65.31 (1659)
66.75 (1696)
69.51 (1766)
69.51 (1766)
72.27 (1836)
72.27 (1836)
74.52 (1893)

305 (139)
234 (107)
300 (137)
241 (110)
337 (153)
343 (156)
348 (158)
355 (162)
355 (162)
355 (162)
355 (162)
448 (204)
427 (194)
440 (200)
635 (289)
641 (291)
641 (291)
648 (294)
648 (294)
674 (306)

1)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

59

10

Technical data

CR, CRI, CRN

Technical data

TM02 7700 1009

CR 45

ANSI dimensions [inch (mm)]


Pump type

CR 45-1-1

P2
[Hp]

7 1/2

CR 45-1

10

CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR

15
15
15
20
25
25
30
30
30
40
40
40
50
50
50
60
60

1)

45-2-2
45-2-1
45-2
45-3-2
45-3-1
45-3
45-4-2
45-4-1
45-4
45-5-2
45-5-1
45-5
45-6-2
45-6
45-7-2
45-7
45-8-1

Ph.

TEFC
B1

1
3
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3

22.20 (564)
22.01 (560)
22.20 (564)
22.01 (560)
29.49 (750)
29.49 (750)
29.49 (750)
32.64 (830)
32.64 (830)
32.64 (830)
35.79 (910)
35.79 (910)
35.79 (910)
38.94 (990)
38.94 (990)
38.94 (990)
42.09 (1070)
42.09 (1070)
45.24 (1150)
45.24 (1150)
48.39 (1230)

D1

D2

B1+B2

D1

D2

B1+B2

10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
15.32 (390)
15.32 (390)
15.32 (390)
16.88 (429)
16.88 (429)
16.88 (429)
19.00 (483)
19.00 (483)

7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
13.11 (333)
14.12 (359)
14.12 (359)
14.12 (359)
14.90 (379)
14.90 (379)

37.73 (959)
37.52 (954)
38.27 (973)
36.74 (934)
48.03 (1220)
48.03 (1220)
48.03 (1220)
51.18 (1300)
55.03 (1398)
55.03 (1398)
58.18 (1478)
58.18 (1478)
58.18 (1478)
62.13 (1579)
62.13 (1579)
62.13 (1579)
69.90 (1776)
69.90 (1776)
73.05 (1856)
76.03 (1932)
79.18 (2012)

10.62 (270)
10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)
15.12 (385)

7.33 (187)
7.33 (187)
7.33 (187)
8.92 (227)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)

45.80 (1164)
45.80 (1164)
45.80 (1164)
52.33 (1330)
53.45 (1358)
53.45 (1358)
57.60 (1464)
57.60 (1464)
57.60 (1464)
62.19 (1580)
62.19 (1580)
62.19 (1580)
64.84 (1647)
64.84 (1647)
67.99 (1727)
71.37 (1813)
74.52 (1893)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

60

Ship. wt.1)
[lbs (kg)]

ODP

259 (118)
243 (111)
314 (143)
243 (111)
347 (158)
347 (158)
347 (158)
361 (164)
353 (161)
353 (161)
426 (194)
432 (196)
432 (196)
634 (288)
634 (288)
634 (288)
679 (308)
679 (308)
689 (313)
869 (395)
878 (399)

Technical data

10
Technical data

CR, CRI, CRN

TM02 7704 1009

CRN 45

ANSI dimensions [inch (mm)]


Pump type

CRN 45-1-1

P2
[Hp]

7 1/2

CRN 45-1

10

CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN

15
15
15
20
25
25
30
30
30
40
40
40
50
50
50
60
60

45-2-2
45-2-1
45-2
45-3-2
45-3-1
45-3
45-4-2
45-4-1
45-4
45-5-2
45-5-1
45-5
45-6-2
45-6
45-7-2
45-7
45-8-1

Ph.

TEFC

Ship. wt.1)
[lbs (kg)]

ODP

B1
1
3
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3

22.20 (564)
22.01 (560)
22.20 (564)
22.01 (560)
29.49 (750)
29.49 (750)
29.49 (750)
32.64 (830)
32.64 (830)
32.64 (830)
35.79 (910)
35.79 (910)
35.79 (910)
38.94 (990)
38.94 (990)
38.94 (990)
42.09 (1070)
42.09 (1070)
45.24 (1150)
45.24 (1150)
48.39 (1230)

D1

D2

B1+B2

D1

D2

B1+B2

10.22 (260)
8.66 (220)
10.23 (260)
10.24 (261)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
12.36 (314)
15.32 (390)
15.32 (390)
15.32 (390)
16.88 (429)
16.88 (429)
16.88 (429)
19.00 (483)
19.00 (483)

7.62 (194)
5.28 (135)
10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
13.11 (333)
14.12 (359)
14.12 (359)
14.12 (359)
14.90 (379)
14.90 (379)

37.73 (959)
37.52 (954)
38.27 (973)
36.74 (934)
48.03 (1220)
48.03 (1220)
48.03 (1220)
51.18 (1300)
55.03 (1398)
55.03 (1398)
58.18 (1478)
58.18 (1478)
58.18 (1478)
62.13 (1579)
62.13 (1579)
62.13 (1579)
69.90 (1776)
69.90 (1776)
73.05 (1856)
76.03 (1932)
79.18 (2012)

10.62 (270)
10.62 (270)
10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)
15.12 (385)

7.33 (187)
7.33 (187)
7.33 (187)
8.92 (227)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)

45.80 (1164)
45.80 (1164)
45.80 (1164)
52.33 (1330)
53.45 (1358)
53.45 (1358)
57.60 (1464)
57.60 (1464)
57.60 (1464)
62.19 (1580)
62.19 (1580)
62.19 (1580)
64.84 (1647)
64.84 (1647)
67.99 (1727)
71.37 (1813)
74.52 (1893)

259 (118)
243 (111)
314 (143)
243 (111)
347 (158)
347 (158)
347 (158)
361 (164)
353 (161)
353 (161)
427 (194)
430 (196)
430 (196)
632 (287)
632 (287)
632 (287)
677 (308)
677 (308)
687 (312)
867 (394)
876 (398)

1)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

61

10

Technical data

CR, CRI, CRN

Technical data

TM02 7701 1009

CR 64

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

TEFC
B1
D1

CR 64-1-1

10

CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
CR

15
20
20
25
30
40
40
40
50
50
60

1)

64-1
64-2-2
64-2-1
64-2
64-3-2
64-3-1
64-3
64-4-2
64-4-1
64-4
64-5-2

1
3
3
3
3
3
3
3
3
3
3
3
3

22.09 (562)
22.09 (562)
26.42 (672)
29.69 (755)
29.69 (755)
29.69 (755)
32.91 (836)
32.91 (836)
32.91 (836)
36.18 (919)
36.18 (919)
36.18 (919)
39.41 (1002)

10.23
10.24
12.36
12.36
12.36
12.36
12.36
15.32
15.32
15.32
16.88
16.88
19.00

(260)
(261)
(314)
(314)
(314)
(314)
(314)
(390)
(390)
(390)
(429)
(429)
(483)

D2

B1+B2

D1

D2

B1+B2

10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
13.11 (333)
14.12 (359)
14.12 (359)
14.90 (379)

38.16 (970)
36.82 (936)
44.96 (1142)
48.23 (1226)
48.23 (1226)
52.08 (1323)
55.30 (1405)
56.10 (1425)
56.10 (1425)
59.37 (1508)
63.99 (1626)
63.99 (1626)
70.20 (1784)

10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)

7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)

42.73 (1086)
49.38 (1255)
49.38 (1255)
50.50 (1283)
54.72 (1390)
56.16 (1427)
56.16 (1427)
59.43 (1510)
58.93 (1497)
58.93 (1497)
65.54 (1665)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

62

Ship. wt.1)
[lbs (kg)]

ODP

268 (122)
252 (115)
348 (158)
363 (165)
363 (165)
355 (162)
430 (196)
624 (284)
624 (284)
624 (284)
676 (307)
676 (307)
866 (393)

Technical data

10
Technical data

CR, CRI, CRN

TM02 7705 1009

CRN 64

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

TEFC
D1

CRN 64-1-1

10

CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN

15
20
20
25
30
40
40
40
50
50
60

64-1
64-2-2
64-2-1
64-2
64-3-2
64-3-1
64-3
64-4-2
64-4-1
64-4
64-5-2

Ship. wt.1)
[lbs (kg)]

ODP

B1
1
3
3
3
3
3
3
3
3
3
3
3
3

22.09 (562)
22.09 (562)
26.42 (672)
29.69 (755)
29.69 (755)
29.69 (755)
32.91 (836)
32.91 (836)
32.91 (836)
36.18 (919)
36.18 (919)
36.18 (919)
39.41 (1002)

10.23
10.24
12.36
12.36
12.36
12.36
12.36
15.32
15.32
15.32
16.88
16.88
19.00

(260)
(261)
(314)
(314)
(314)
(314)
(314)
(390)
(390)
(390)
(429)
(429)
(483)

D2

B1+B2

D1

D2

B1+B2

10.30 (262)
6.26 (160)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
13.11 (333)
14.12 (359)
14.12 (359)
14.90 (379)

38.16 (970)
36.82 (936)
44.96 (1142)
48.23 (1226)
48.23 (1226)
52.08 (1323)
55.30 (1405)
56.10 (1425)
56.10 (1425)
59.37 (1508)
63.99 (1626)
63.99 (1626)
70.20 (1784)

10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)

7.33 (187)
8.92 (227)
8.92 (227)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)

42.73 (1086)
49.38 (1255)
49.38 (1255)
50.50 (1283)
54.72 (1390)
56.16 (1427)
56.16 (1427)
59.43 (1510)
58.93 (1497)
58.93 (1497)
65.54 (1665)

269 (123)
253 (115)
349 (159)
364 (166)
364 (166)
357 (162)
432 (196)
625 (284)
625 (284)
625 (284)
678 (308)
678 (308)
868 (394)

1)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

63

10

Technical data

CR, CRI, CRN

Technical data

CR 90
4-5 STAGES

D1

4" ANSI
250 LB R.F.

D2

G 12

8X 78
9
4X 16

B2

5 78 7 78

10

3 15
16

1 34

11
13 11
16

1-3 STAGES
G 12

8X 34
9
4X 16

6 18 7 12

1
2

7 78
10

3 15
16

1 34

5
16

9
TM02 7702 3804

B1

4" ANSI
125 LB R.F.

PRIMING
PORT G 1 2

G 1 2 PLUG
WITH 1/4"
TAP FOR
SENSOR/
GAUGE

11
13 11
16

15

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

15
20
25
30
40
40
50
50
60
60

3
3
3
3
3
3
3
3
3
3

TEFC
D1

CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
1)

90-1-1
90-1
90-2-2
90-2-1
90-2
90-3-2
90-3-1
90-3
90-4-2
90-4-1

26.81
26.81
30.43
30.43
30.43
34.06
34.06
34.06
37.68
37.68

(681)
(681)
(773)
(773)
(773)
(866)
(866)
(866)
(958)
(958)

12.36
12.36
12.36
12.36
15.32
15.32
16.88
16.88
19.00
19.00

(314)
(314)
(314)
(314)
(390)
(390)
(429)
(429)
(483)
(483)

D2

B1+B2

D1

D2

B1+B2

8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
14.12 (359)
14.12 (359)
14.90 (379)
14.90 (379)

45.35 (1152)
45.35 (1152)
52.82 (1342)
52.82 (1342)
53.62 (1362)
57.25 (1455)
61.87 (1572)
61.87 (1572)
68.47 (1740)
68.47 (1740)

10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)
15.12 (385)

7.33 (187)
8.92 (227)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)

43.12 (1096)
46.50 (1182)
51.24 (1302)
52.24 (1327)
53.68 (1364)
57.31 (1456)
56.81 (1443)
56.81 (1443)
63.81 (1621)
63.81 (1621)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

64

Ship. wt.1)
[lbs (kg)]

ODP

B1

358 (163)
363 (165)
367 (167)
432 (196)
625 (284)
636 (289)
667 (303)
667 (303)
869 (395)
869 (395)

Technical data

10
Technical data

CR, CRI, CRN

CRN 90
D1

4 STAGES

4" ANSI
300 LB R.F.

D2

G 12

8X 78
B2

9
4X 16

6 81 7 78

10

3 15
16

1 34

11
13

11
16

1-3 STAGES

4 " ANSI
150 LB R.F.
PRIMING
PORT G 1 2

G 1 2 PLUG
WITH 1/4"
TAP FOR
SENSOR/
GAUGE

G 12

8X 34
9
4X 16

6 81 7 21 9

1
2

7 78
10

3 15
16

1 34

5
16

11
13

15

TM02 7706 3804

B1

11
16

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

15
20
25
30
40
40
50
50
60
60

3
3
3
3
3
3
3
3
3
3

TEFC
D1

CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN

90-1-1
90-1
90-2-2
90-2-1
90-2
90-3-2
90-3-1
90-3
90-4-2
90-4-1

Ship. wt.1)
[lbs (kg)]

ODP

B1
26.81
26.81
30.43
30.43
30.43
34.06
34.06
34.06
37.68
37.68

(681)
(681)
(773)
(773)
(773)
(866)
(866)
(866)
(958)
(958)

12.36
12.36
12.36
12.36
15.32
15.32
16.88
16.88
19.00
19.00

(314)
(314)
(314)
(314)
(390)
(390)
(429)
(429)
(483)
(483)

D2

B1+B2

D1

D2

B1+B2

8.00 (204)
8.00 (204)
8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
14.12 (359)
14.12 (359)
14.90 (379)
14.90 (379)

45.35 (1152)
45.35 (1152)
52.82 (1342)
52.82 (1342)
53.62 (1362)
57.25 (1455)
61.87 (1572)
61.87 (1572)
68.47 (1740)
68.47 (1740)

10.62 (270)
11.50 (293)
11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)
15.12 (385)

7.33 (187)
8.92 (227)
8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)

43.12 (1096)
46.50 (1182)
51.24 (1302)
52.24 (1327)
53.68 (1364)
57.31 (1456)
56.81 (1443)
56.81 (1443)
63.81 (1621)
63.81 (1621)

364
369
372
450
631
642
668
672
876
876

(166)
(168)
(169)
(205)
(287)
(292)
(304)
(305)
(398)
(398)

1)

Weights are based on pump with TEFC motor (see price list for individual weights).
All dimensions in inches unless otherwise noted.

65

10

Technical data

CR, CRI, CRN

Technical data

CR 120
1-1 to 4-2 STAGES
5" FLANGE2)

TM04 9630 4810

4-1 to 5-1 STAGES


5" FLANGE2)

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

20
25
40
40
50
60
60
75
75

3
3
3
3
3
3
3
3
3

32.83 (834)
32.83 (834)
38.98 (991)
38.98 (991)
38.98 (991)
45.08 (1146)
45.08 (1146)
45.08 (1146)
51.69 (1313)

12.36
12.36
15.32
15.32
16.88
19.00
19.00
19.00
19.00

(314)
(314)
(390)
(390)
(429)
(483)
(483)
(483)
(483)

8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
14.12 (359)
14.90 (379)
14.90 (379)
14.90 (379)
14.90 (379)

51.37
55.22
62.17
62.17
66.79
75.87
75.87
75.87
82.48

100
100
100
125

3
3
3
3

51.69
51.69
57.80
57.80

19.00 (483)
19.00 (483)
19.00 (483)
-

17.38 (442)
17.38 (442)
17.38 (442)
-

82.51 (2096)
82.51 (2096)
88.62 (2251)
-

TEFC
D1

CR 120-1-1
CR 120-1
CR 120-2-2
CR 120-2-1
CR 120-2
CR 120-3-2
CR 120-3-1
CR 120-3
CR 120-4-2
CR 120-4-1
CR 120-4
CR 120-5-2
CR 120-5-13)
1)

Ship. wt.1)
[lbs (kg)]

ODP

B1

(1313)
(1313)
(1469)
(1469)

D2

B1+B2
(1305)
(1403)
(1580)
(1580)
(1697)
(1928)
(1928)
(1928)
(2095)

D1

D2

11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)
15.12 (385)
15.18 (386)
15.18 (386)

8.92 (227)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)

52.52
53.64
62.23
62.23
61.73
71.21
71.21
71.21
77.82

(1335)
(1363)
(1581)
(1581)
(1568)
(1809)
(1809)
(1809)
(1977)

432 (196)
424 (110)
704 (320)
704 (320)
735 (334)
936 (425)
936 (425)
1045 (475)
1199 (544)

15.12
15.12
15.12
16.81

13.19
13.19
13.19
16.39

79.07
79.07
85.18
88.77

(2009)
(2009)
(2164)
(2255)

1468 (666)
1468 (666)
1490 (676)
1191 (541)

(385)
(385)
(385)
(427)

(336)
(336)
(336)
(417)

B1+B2

Weights are based on pump with TEFC motor (see price list for individual weights).
This is a 5" loose flange ring. When using a 5" mating flange, the gasket contact surface is reduced to approximately 0.25". A 4" loose flange ring is
available for 4" pipe work. This will provide a standard gasket contact surface. Also available is a 6" ANSI flange adapter manufactured to ANSI
B16.5 specifications.
3)
CR 120-5-1, 125 Hp, ODP motor only.
All dimensions in inches unless otherwise noted.
2)

66

Technical data

10
Technical data

CR, CRI, CRN

CRN 120
1-1 to 4-2 STAGES
5" FLANGE2)

TM04 9631 4810

4-1 to 5-1 STAGES


5" FLANGE2)

ANSI dimensions [inch (mm)]


Pump type

CRN 120-1-1
CRN 120-1
CRN 120-2-2
CRN 120-2-1
CRN 120-2
CRN 120-3-2
CRN 120-3-1
CRN 120-3
CRN 120-4-2
CRN 120-4-1
CRN 120-4
CRN 120-5-2
CRN 120-5-13)

P2
[Hp]

Ph.

20
25
40
40
50
60
60
75
75
100
100
100
125

3
3
3
3
3
3
3
3
3
3
3
3
3

TEFC

Ship. wt.1)
[lbs (kg)]

ODP

B1
32.83 (834)
32.83 (834)
38.98 (991)
38.98 (991)
38.98 (991)
45.08 (1146)
45.08 (1146)
45.08 (1146)
51.69 (1313)
51.69 (1313)
51.69 (1313)
57.80 (1469)
57.80 (1469)

D1

D2

12.36 (314)
12.36 (314)
15.32 (390)
15.32 (390)
16.88 (429)
19.00 (483)
19.00 (483)
19.00 (483)
19.00 (483)
19.00 (483)
19.00 (483)
19.00 (483)
-

8.00 (204)
8.00 (204)
13.11 (333)
13.11 (333)
14.12 (359)
14.90 (379)
14.90 (379)
14.90 (379)
14.90 (379)
17.38 (442)
17.38 (442)
17.38 (442)
-

B1+B2
51.37
55.22
62.17
62.17
66.79
75.87
75.87
75.87
82.48
82.51
82.51
88.62

(1305)
(1403)
(1580)
(1580)
(1697)
(1928)
(1928)
(1928)
(2095)
(2096)
(2096)
(2251)
-

D1

D2

B1+B2

11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
13.25 (337)
15.12 (385)
15.12 (385)
15.18 (386)
15.18 (386)
15.12 (385)
15.12 (385)
15.12 (385)
16.81 (427)

8.92 (227)
8.94 (228)
12.21 (311)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
16.39 (417)

52.52 (1335)
53.64 (1363)
62.23 (1581)
62.23 (1581)
61.73 (1568)
71.21 (1809)
71.21 (1809)
71.21 (1809)
77.82 (1977)
79.07 (2009)
79.07 (2009)
85.18 (2164)
88.77 (2255)

439 (200)
431 (196)
711 (323)
711 (323)
742 (337)
943 (428)
943 (428)
1052 (478)
1206 (548)
1475 (670)
1475 (670)
1497 (680)
1200 (545)

1)

Weights are based on pump with TEFC motor (see price list for individual weights).
This is a 5" loose flange ring. When using a 5" mating flange, the gasket contact surface is reduced to approximately 0.25". A 4" loose flange ring is
available for 4" pipe work. This will provide a standard gasket contact surface. Also available is a 6" ANSI flange adapter manufactured to ANSI
B16.5 specifications.
3)
CRN 120-5-1, 125 Hp, ODP motor only.
All dimensions in inches unless otherwise noted.
2)

67

10

Technical data

CR, CRI, CRN

Technical data

CR 150
1 to 3 STAGES
5" FLANGE2)

TM04 9632 4810

4 to 5 STAGES
5" FLANGE2)

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

25
30
40
50
60
75
75
100
100
100

3
3
3
3
3
3
3
3
3
3

TEFC
D1

CR
CR
CR
CR
CR
CR
CR
CR
CR
CR
1)

150-1-1
150-1
150-2-2
150-2-1
150-2
150-3-2
150-3-1
150-3
150-4-2
150-4-1

Ship. wt.1)
[lbs (kg)]

ODP

B1
32.83 (834)
32.83 (834)
38.98 (991)
38.98 (991)
38.98 (991)
45.55 (1157)
45.55 (1157)
45.55 (1157)
51.69 (1313)
51.69 (1313)

12.36
12.36
15.32
16.88
19.00
19.00
19.00
19.00
19.00
19.00

(314)
(314)
(390)
(429)
(483)
(483)
(483)
(483)
(483)
(483)

D2
8.00 (204)
8.00 (204)
13.11 (333)
14.12 (359)
14.90 (379)
14.90 (379)
14.90 (379)
17.38 (442)
17.38 (442)
17.38 (442)

B1+B2
55.22
55.22
62.17
66.79
69.77
76.34
76.34
76.37
82.51
82.51

(1403)
(1403)
(1580)
(1697)
(1773)
(1940)
(1940)
(1940)
(2096)
(2096)

D1

D2

B1+B2

11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
15.12 (385)
15.18 (386)
15.18 (386)
15.12 (385)
15.12 (385)
15.12 (385)

8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)

53.64 (1363)
54.64 (1388)
62.23 (1581)
61.73 (1568)
65.11 (1654)
71.68 (1821)
71.68 (1821)
72.93 (1853)
79.07 (2009)
79.07 (2009)

424 (193)
490 (223)
705 (320)
735 (334)
915 (416)
1178 (535)
1178 (535)
1215 (552)
1234 (560)
1234 (560)

Weights are based on pump with TEFC motor (see price list for individual weights).
This is a 5" loose flange ring. When using a 5" mating flange, the gasket contact surface is reduced to approximately 0.25". A 4" loose flange ring is
available for 4" pipe work. This will provide a standard gasket contact surface. Also available is a 6" ANSI flange adapter manufactured to ANSI
B16.5 specifications.
All dimensions in inches unless otherwise noted.

2)

68

Technical data

10
Technical data

CR, CRI, CRN

CRN 150
1 to 3 STAGES
5" FLANGE2)

TM04 9633 4810

4 to 5 STAGES
5" FLANGE2)

ANSI dimensions [inch (mm)]


Pump type

P2
[Hp]

Ph.

25
30
40
50
60
75
75
100
100
100

3
3
3
3
3
3
3
3
3
3

TEFC
D1

CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN
CRN

150-1-1
150-1
150-2-2
150-2-1
150-2
150-3-2
150-3-1
150-3
150-4-2
150-4-1

Ship. wt.1)
[lbs (kg)]

ODP

B1
32.83 (834)
32.83 (834)
38.98 (991)
38.98 (991)
38.98 (991)
45.55 (1157)
45.55 (1157)
45.55 (1157)
51.69 (1313)
51.69 (1313)

12.36
12.36
15.32
16.88
19.00
19.00
19.00
19.00
19.00
19.00

(314)
(314)
(390)
(429)
(483)
(483)
(483)
(483)
(483)
(483)

D2
8.00 (204)
8.00 (204)
13.11 (333)
14.12 (359)
14.90 (379)
14.90 (379)
14.90 (379)
17.38 (442)
17.38 (442)
17.38 (442)

B1+B2
55.22
55.22
62.17
66.79
69.77
76.34
76.34
76.37
82.51
82.51

(1403)
(1403)
(1580)
(1697)
(1773)
(1940)
(1940)
(1940)
(2096)
(2096)

D1

D2

B1+B2

11.50 (293)
11.50 (293)
13.25 (337)
13.25 (337)
15.12 (385)
15.18 (386)
15.18 (386)
15.12 (385)
15.12 (385)
15.12 (385)

8.94 (228)
8.94 (228)
12.21 (311)
12.21 (311)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)
13.19 (336)

53.64 (1363)
54.64 (1388)
62.23 (1581)
61.73 (1568)
65.11 (1654)
71.68 (1821)
71.68 (1821)
72.93 (1853)
79.07 (2009)
79.07 (2009)

431 (196)
496 (225)
711 (323)
741 (337)
922 (419)
1184 (538)
1184 (538)
1222 (555)
1243 (564)
1243 (564)

1)

Weights are based on pump with TEFC motor (see price list for individual weights).
This is a 5" loose flange ring. When using a 5" mating flange, the gasket contact surface is reduced to approximately 0.25". A 4" loose flange ring is
available for 4" pipe work. This will provide a standard gasket contact surface. Also available is a 6" ANSI flange adapter manufactured to ANSI
B16.5 specifications.
All dimensions in inches unless otherwise noted.

2)

69

11

CR, CRI, CRN

Motor data

11. Motor data


Standard motors in the CR range

It is not recommended that an off-the-shelf standard


Baldor motor be used on a Grundfos pump. Ideally, the
best motor choice would be the Grundfos specified
motor.
Single-phase Grundfos specified motors up to 7.5 Hp
have a built-in thermal overload switch.
Other motor types are available (i.e., Explosion proof,
Mill and Chem duty, Premium Efficiency, etc.); consult
local Grundfos company for more information.
Pumps supplied by Grundfos Canada are normally
supplied with motors from other manufactures. 575 volt
motors meet NEMA energy efficient standards.
Dimensions and data will vary, contact local Grundfos
company for more information.
All values are subject to change without notice.

Motors used in the CR pump range are:


Grundfos ML motors
Grundfos specified Baldor motors.
The information in the tables below applies to following
motors type and size:
Type
ML
Baldor

Phase

Motor range [Hp]

Cooling method

3
1
3
3

1/3 - 30
1/3 - 10
40 - 100
15 - 125

TEFC
TEFC
TEFC
ODP

Grundfos CR pumps are supplied with heavy-duty 2pole, NEMA energy efficient C-frame motors built or
selected to our rigid specifications. All CR pump
motors have heavy-duty bearings for maximum thrust
requirements.

ODP motors
(Open Drip Proof, constant speed)

70

ODP
motor
eff. %

ODP
insul.
class

ODP
KVA
code

ODP full
load
current

37-35/17.5

40-39.4/19.7

225-248/124

48/24

55/27.5

306/153

64-59/29.5

74-67/33.5

335-374/187

70/35

80/40

480/240

94/47

108/54

542/271

92.4

116/58

134/67

706/353

93

132/66

152/76

844/422

Ph

ODP frame

15

254TCZ

1.15

208-230/460

89.5

20

254TC

1.15

230/460

90.2

25

284TSCZ

1.15

208-230/460

91

30

284TSC

1.15

230/460

91

40

286TSCZ

1.15

230/460

91.7

50

324TSCZ

1.15

230/460

60

324TSCZ

1.15

230/460

ODP service ODP starting


factor current
current

75

364TSCZ

1.15

230/460

93

168/84

192/96

1110/555

100

365TSCZ

1.15

230/460

93

226/113

260/130

1380/690

125

405TSCZ

1.15

460

93.6

140

171

897

Baldor motor

TM02 7696 3803

ODP ODP voltage


S.F.
[V]

Hp

11

CR, CRI, CRN

Motor data

TEFC motors
(Totally Enclosed Fan Cooled, constant speed)

Hp

1/3
1/2
3/4
1
1 1/2
2
3
5
7 1/2
10
15

S.F.

Motor eff. Insul. KVA


[%]
class code

GR 7845

Gr7848sh
Voltage
[V]

TM04 2512 2708

Grundfos ML motors

TM02 7696 3803

Baldor motor

Full load current


[A]

Service factor
current
[A]

Starting current
[A]

Motor
type

7.6/3.8

28/14

Baldor

1.5-1.45/0.75

7.1-7.7/3.9

ML

9.8/4.9

39/19.5

Baldor

1.64-1.55/0.78

2.0-1.9/0.95

9.7-10.1/5.1

ML

9.6/4.8

11.4/5.7

56/28

Baldor

Ph

Frame

56C

1.35

115/230

55

6.0/3.0

56C

1.35

208-230/460

78.5

1.12-1.1/0.55

56C

1.6

115/230

62

7.4/3.7

56C

1.25

208-230/460

78.5

56C

1.25

115/230

66

56C

1.25

208-230/460

79

2.4-2.3/1.2

2.9-2.75/1.4

14.2-15/7.8

ML

56C

1.25

115/230

66

12/6.0

14.4/7.2

77/38.5

Baldor

56C

1.25

208-230/460

80

3.25-3.35/1.68

4.0-3.9/1.95

19.2-21.8/10.9

ML

56C

1.3

115/208-230

71

17/9.5-8.6

20.4/11.3-10.2

106/58.6-53

Baldor

56C

1.15

208-230/460

84

4.7-4.6/2.3

5.2-5.1/2.55

33.8-36.8/18.4

ML

56C

1.15

115/208-230

74

23/12.7-11.5

25.4/14.0-12.7

156/86-78

Baldor

56C

1.15

208-230/460

85.5

5.7-5.4/2.7

6.55-6.1/3.05

46.2-48.6/24.3

ML

182TC

1.15

115/208-230

75

29/16-14.5

31.8/18-15.9

170/94-85

Baldor

182TC

1.15

208-230/460

86.5

8.35-7.50/3.75

9.10-8.15/4.10

86.8-78.0/39.0

ML

213TCZ

1.15

208-230

80

24-22

27-25

188-170

Baldor

182TC

1.15

208-230/460

88.5

14.1-13.1/7.29

16.2-15.0/8.4

207-193/107

ML

213TC

1.15

208-230

82

33.8-31

38.5-35.5

244-220

Baldor

213TC

1.15

208-230/460

89.5

19.5-18.1/9.09

22.4-20.8/10.4

289-267/135

ML

213TC

1.15

230

85.5

40

46

284

Baldor

215TC

1.15

208-230/460

90.2

26.5-24.6/12.4

29.0-27.0/13.6

261-243/123

ML

254TC

1.15

208-230/460

91

37.5-34/17

41.0-37.5/18.6

369-338/168

ML

20

254TC

1.15

208-230/460

91

50.5-46/23

55.5-50.5/25.5

450-410/207

ML

25

284TSC

1.15

230/460

91.7

62.0-56/28

68.0-61.5/31.0

510-462/233

ML

30

286TSC

1.15

230/460

91.7

74.0-67.0/33.5

81.5-73.5/37.0

595-537/271

ML

40

286TSC

1.15

230/460

91.7

88/44

102/51

614/307

Baldor
Baldor

50

326TSC

1.15

230/460

93

110/55

128/64

746/393

60

364TSC

1.15

230/460

93

134/67

154/77

918/459

Baldor

75

365TSC

1.15

230/460

93

166/83

188/94

1162/581

Baldor

100

405TSC

1.15

230/460

93.6

216/108

246/123

1422/711

Baldor

71

12

CR, CRI, CRN

Accessories

12. Accessories
Pipework connections
For pipework connection, various sets of counter
flanges and couplings are available.

Adapter kit
6" flanges are available for CR, CRN 120 and 150
pumps. To use 6" flanges, two adapter kits must be
ordered per pump.

TM04 0021 4807

Adapter kit

6 3/16

Pump type

Pipe
connection

Number of
flange kits
needed

Product
number

CR 120
CR 150

6" RF
250 lb.
Ductile iron

96638184

CRN 120
CRN 150

6" RF
300 lb.
ANSI 316 SS

96638186

9 1/4

Counter flanges for CR


A set consists of two counter flanges, two gaskets,
bolts and nuts.
Counter flange

Pump type

Description

Pressure class

Pipework
connection

Product
number

TM02 5691 3802

3/4"

3-1/16"
3-7/8"
5-1/2"

CR 1s
CR 1
CR 3
CR 5

Threaded

ANSI 250 lb.

1 1/4" NPT

91122260

CR 10
CR 15
CR 20

Threaded

ANSI 250 lb.

2" NPT

335021

Threaded

ANSI 125 lb.

2 1/2" NPT

559601

Threaded

ANSI 250 lb.

2 1/2" NPT

345050

Threaded

ANSI 125 lb.

3" NPT

569601

Threaded

ANSI 250 lb.

3" NPT

91121952

TM02 5692 3802

3/4"

4-3/16"
5"
6-1/2"

ANSI 300 LB.


7/8"

5-1/2"
7"

5-11/16"

6"
7-1/2"

72

CR 32

7/8"

6-5/8"
8-1/4"

TM02 5695 + 5696 3802

3/4"

5-7/8"
7-1/2"

TM02 5693 + 5694 3802

ANSI 150 LB.


3/4"

CR 45

Counter flange

Pipework
connection

Product
number

Threaded

ANSI 125 lb.

4" NPT

579801

Threaded

ANSI 250 lb.

4" NPT

3600028

Threaded

ANSI 125 lb.

5" NPT

91121956

Threaded

ANSI 250 lb.

5" NPT

91121957

Pressure class

Pipework
connection

Product
number

Description

ANSI 250 LB.


TM02 5697 + 5698 3802

7/8"

6-15/16"

7-1/2"
9"

7-7/8"
10"

7.31

7.31

8.5

9.25

10.0

11.0

TM06 0509 1109

ANSI 125 LB.


3/4"

Pressure class

Pump type

Accessories

12

CR, CRI, CRN

CR 64
CR 90

CR 120
CR 150

Counter flanges for CRN


Counterflanges for CRN pumps are made of stainless
steel according to AISI 316.
A set consists of two counter flanges, two gaskets,
bolts and nuts.
Counter flange

Pump type

Description

TM02 5691 3802

3-1/16"
3-7/8"
5-1/2"

CRI, CRN
1s, 1, 3 and 5

Threaded

ANSI 300 lb.

1 1/4" NPT

91129013

TM02 5692 3802

3/4"

CRI,
CRN
10, 15, 20

Threaded

ANSI 300 lb.

2" NPT

339919

Threaded

ANSI 150 lb.

2 1/2" NPT

91121951

Threaded

ANSI 300 lb.

2 1/2" NPT

0ID00138

Threaded

ANSI 150 lb.

3" NPT

91121953

Threaded

ANSI 300 lb.

3" NPT

91121954

3/4"

4-3/16"
5"
6-1/2"
ANSI 150 LB.

5-7/8"
7-1/2"

5-1/2"
7"

3/4"

7/8"

5-11/16"

6"
7-1/2"

6-5/8"
8-1/4"

TM02 5693 + 5694 3802

ANSI 300 LB.


7/8"

TM02 5695 + 5696 3802

3/4"

CRN 32

CRN 45

73

12

CR, CRI, CRN

Accessories

Counter flange
ANSI 150 LB.

Pressure class

Pipework
connection

Product
number

Threaded

ANSI 150 lb.

4" NPT

0ID00148

Threaded

ANSI 300 lb.

4" NPT

91121955

Threaded

ANSI 150 lb.

5" NPT

91121958

Threaded

ANSI 300 lb.

5" NPT

91121959

Description

ANSI 300 LB.


7/8"

TM02 5697 + 5698 3802

3/4"

Pump type

6-15/16"

7-7/8"
10"

7.31

7.31

8.5

9.25

10.0

CRN 120
CRN 150

TM06 0509 1109

7-1/2"
9"

CRN 64
CRN 90

11.0

PJE couplings for CRN


Couplings for CRN pumps are made of stainless steel
according to AISI 316.
A set consists of two couplings, two gaskets, two pipe
stub and bolts and nuts.

Couplings

Pump type

Pipe stub

TM00 3808 1094

CRI, CRN
Threaded
1s, 1, 3 and 5

CRI
CRN
Threaded
10, 15 and 20

Rated
Pipework
pressure connection

1160 psi

1015 psi

Rubber
parts

Number of
coupling
sets
needed

Product
number

EPDM

4013010

FKM

0ID00118

EPDM

331301

FKM

0ID00128

1 1/4" NPT

2" NPT

FlexiClamp base connections


All sets comprise the necessary number of bolts and
nuts as well as a gasket/O-ring.
Base connections

Pump type

Connection

TM02 1145 0601

TM02 1144 0601

Oval
(cast iron)

74

CRI, CRN
1s, 1, 3 and 5
Oval
(stainless steel)

CRI, CRN
1s, 1, 3 and 5

Union
ext. threaded

Pipework
connection

Rubber parts

Product
number

1" NPT

Klingersil

96468491

1 1/4" NPT

Klingersil

96470781

1" NPT

Klingersil

96480850

1 1/4" NPT

Klingersil

96480851

EPDM

96480852

FKM

96480853

2" NPT

Pump type

TM02 1146 0601

Base connections

CRI, CRN
1s, 1, 3 and 5

Connection

ANSI (FGJ)
(stainless steel)

Pipework
connection

Rubber parts

Product
number

EPDM

96480858

FKM

96480859

EPDM

96480854

FKM

96480855

EPDM

96480856

FKM

96480857

Accessories

12

CR, CRI, CRN

1 1/4" NPT

TM02 7238 2803

TM02 7237 2803

TM02 1147 0601

1" NPT
CRI, CRN
1s, 1, 3 and 5

Clamp, threaded
pipe stub
1 1/4" NPT

Oval (cast iron)

2" NPT

Klingersil

96498838

Oval (stainless
steel)

2" NPT

Klingersil

96498839

EPDM

96511402

FKM

96511403

EPDM

96500271

FKM

96500272

EPDM

96500273

FKM

96500274

EPDM

96508602

FKM

96508603

CRI, CRN
10, 15 and 20

CRI, CRN
10, 15 and 20

ANSI (FGJ)
(stainless steel)

2" NPT

1 1/2" NPT

TM02 7239 2803

CRI, CRN
10, 15 and 20

Clamp, threaded
pipe stub

2" NPT

2" NPT

75

12

CR, CRI, CRN

Accessories

CR flange guide

What factors determine the required pressure


class?

Commonly asked questions

Pressure ratings are affected by:


Material
sealing methods
operating temperatures.

What is the "pressure class"?


The pressure class is a pressure rating expressed
as a dimensionless number.
Pressure class does not affect the pump working
pressure.
The class rating charts in ANSI B16.5 give actual
pounds per square inch maximum allowable
pressure at a given temperature.
150 lb, 150# or Class 150 are different ways to write
the same pressure class.

The multiflange used on a CR 1s through 20 can be


used on both 125 lb and 250 lb installations.
The multiflange on a CRI/CRN 1s through 20 can be
used on both 150 lb and 300 lb installations.
All other mating flange classes must match the
pump flange class.
Size

Material

Pressure
class

Mate with:

CR 1s to 5

1.25 in

Cast Iron

250 lb

125 or 250 lb

CRI, CRN 1s to 5

1.25 in

Ductile Iron

300 lb

150 or 300 lb

CR 10 to 20

2 in

Cast Iron

250 lb

125 or 250 lb

CRI, CRN 10 to 20

2 in

Ductile Iron

300 lb

150 or 300 lb

Pump

76

Are pump flanges compatible with mating flanges


of a different pressure class?

Flange

13

CR, CRI, CRN

Lists of variants - on request


Although the Grundfos CR, CRI, CRN product range
offers a number of pumps for different applications,
customers require specific pump solutions to satisfy
their needs.
Below please find the range of options available for
customizing the CR pumps to meet the customers'
demands. Contact Grundfos for further information or
for requests other than the ones mentioned below.

Motors
Variant

Description

Explosion proof
motors

For operation in hazardous atmospheres,


explosion-proof or dust-ignition-proof
motors may be required.

Motors with anticondensation heating


unit

For operation in humid environments


motors with built-in anti-condensation
heating may be required.

Premium efficient
motors

Grundfos offers motors from 1 to 100 Hp


with a Premium efficiency class.

Different motor brand

Oversized motor

4-pole motors

If technically possible, Grundfos can fit the


pump with a motor of a brand other than the
standard. This will normally increase the
time of delivery. Alternatively, the pump can
be supplied without a motor (motor thrust
rating must be checked).
Ambient temperatures above 104 F or
installation at altitudes of more than 3280 ft
above sea level require the use of an
oversized motor (i.e. derating).
Grundfos offers standard motors fitted with
4-poles.

Connections and other variants


Variant

Pipe connections

TriClamp connections

Electropolished
pumps

Description
In addition to the wide range of standard
flange connections, a 232 psi DIN standard
clamping flange is available.
Customized flanges are available
according to specifications.
TriClamp connections are of a hygienic
design with a sanitary coupling for use in
the pharmaceutical and food industry.
To substantially reduce the risk of corrosion
of the materials.
For use in the pharmaceutical/food
industry.

Variants

13. Variants
Shaft seals
Variant

Description

Shaft seal with Shaft seals with FFKM or FXM o-ring material are
recommended for applications where the pumped
FFKM O-ring
liquid may damage the standard O-ring material.
material
Seal with flush, Recommended for applications involving
quench seal
crystallizing, hardening or sticky liquids.
Recommended for applications involving extremely
high temperatures.
No conventional mechanical shaft seal can
withstand liquid temperatures of up to 356 F for

Cool-Top
any length of time.
shaft seal
For that type of application, Grundfos' unique aircooled shaft seal system is recommended.
system
In order to ensure a low liquid temperature around
the standard shaft seal, the pump is fitted with a
special air-cooled shaft seal chamber.
No separate cooling is required.
Recommended for applications involving poisonous
or explosive liquids.
Protects the surrounding environment and the
Double shaft
people working in the vicinity of the pump.
seal with
Consists of two seals mounted in a "back-to-back"
pressure
arrangement inside a separate pressure seal
chamber
chamber. As the pressure in the chamber is higher
than the pump pressure, leakage is prevented. A
dosing pump or a special pressure-intensifier
generates the seal chamber pressure.
Magnetically driven pumps for industrial
applications.
Key applications are industrial processes involving
CRN MAGdrive
the handling of aggressive, environmental,
dangerous or volatile liquids, e.g. organic
compounds, solvents, etc.

Pumps
Variant

Horizontally
mounted pump

Low-temperature
pump to -40 F

High-speed pump
up to 681 psi

High-pressure
pump up to 696 psi
Low-NPSH pump
(improved suction)
Belt-driven pumps
Pumps for
pharmaceutical and
biotechnological
applications

Description
For safety or height reasons, certain
applications, for instance on ships, require the
pump to be mounted in the horizontal position.
For easy installation the pump is equipped
with brackets that support motor and pump.
Exposed to temperatures down to -40 F,
coolant pumps may require neck-rings with a
different diameter in order to prevent impeller
drag.
For high-pressure applications, a unique pump
capable of generating up to 681 psi pressure
is available.
The pump is equipped with a high-speed
motor, type MLE. The direction of rotation is
the opposite of that of standard pumps, and
the chamber stack is turned upside-down, as a
result of which the pumped liquid flows in the
opposite direction.
For high-pressure applications, a unique
double pump system capable of generating up
to 696 psi pressure is available.
Recommended for boiler-feed applications
where cavitation may occur due to poor inlet
conditions.
Belt-driven pumps designed to operate in
places with limited space or where no
electrical power is available.
CRN pumps designed for applications
requiring the sterilization and CIP capability of
pipes, valves and pumps. (CIP = Cleaning-InPlace).

77

13

CR, CRI, CRN

Variants

This page intentionally left blank.

78

14

CR, CRI, CRN

CR, CRI, CRN

Submittal data

14. Submittal data


Company name:
Prepared by:

Vertical Multistage Centrifugal Pumps

Phone number:

(____)

Fax number:

(____)

Date:

Page 1 of:

Quote number:

Client Information
Project title:
Reference number:
Client contact:

Client name:
Client number:
Client phone number: (____)

Location Information
For:
Site:
Address:

Unit:
Service:
City:

State:

Zip Code:

Application Information
Operating Conditions

Pumped Fluid
Fluid type:

Max.

Norm.

Min.

Capacity (gpm)

Rated

Max.

Norm.

Fluid Temperature ( F)
at designated
temperature
Specific Gravity
Vapor Pressure (psia)

Suction Pressure (psig)


Discharge Pressure (psig)
Differential Head (ft)
Hydraulic Power (Hp)
at designated capacity
NPSH Available (ft)

Viscosity (cp)

Fluid ph:

Chlorides (ppm):

Service

Hazardous:

Continuous
Intermittent (starts/day):

Flammable:
Other:

Corrosion/Erosion
caused by:

Pump Information
Model Information from Type Key and Codes:
Quantity Required:
Minimum required flow:

----> (Example: CR 5-10 A-FGJ-A-E-HQQE )


NPSH required at duty point:

Product Guide additional information pages


Materials page number:
Technical data page number:

Performance curve page number:


Motor data page number:

Motor Information
Hp:

Phase:

Voltage:

Enclosure:

Custom-built pump information (optional):

Additional Information

79

14

CR, CRI, CRN

Submittal data

This page intentionally left blank.

80

15

CR, CRI, CRN

Quotation text

15. Quotation text


CR, CRI, CRN
Vertical, non-self-priming, multistage, in-line, centrifugal pump for installation in pipe systems and mounting on a
foundation.
The pump has the following characteristics:
Impellers and intermediate chambers are made of AISI __________________ Stainless steel
Pump head and base are made of
__________________
Power transmission is via cast iron split coupling.
Pipework connections is via
___________________
The motor is a
___________________ -phase AC motor
Technical
Rated flow:
Rated head:
Minimum liquid temperature:
Maximum liquid temperature:
Type of shaft seal:

_______________________
_______________________
_______________________
_______________________
_______________________

gpm
Feet
F
F

Materials
Material, pump housing:
Material, shaft:
Material, impeller:
Material, sleeve:
Material, seal metal:
seal face:
seal face
seal elastomer:

_______________________
AISI____________________
AISI____________________
AISI____________________
AISI____________________
_______________________
_______________________
_______________________

Stainless
Stainless
Stainless
Stainless

Steel
Steel
Steel
Steel

Installation
Maximum ambient temperature:
Max. pressure at stated temp.:
Standard, pipe connection:
Size, pipe connection:
Rated pressure, pipe connection:
Frame size for motor:

_______________________ F
_______________________ PSI / F
_______________________
_______________________
_______________________ PSI
_______________________ NEMA

Electrical data
Motor type:
Rated power (P2):
Frequency:
Rated voltage:
Rated current:
Service factor:
Starting current:
Rated speed:
Full load motor efficiency:
Insulation class:

_______________________
_______________________
_______________________
_______________________
_______________________
_______________________
_______________________
_______________________
_______________________
_______________________

Hp
Hz
V
A
A
RPM
%

Additional
Gross weight:
Shipping volume:
Model:

_______________________ Lbs.
_______________________
_______________________

81

15

CR, CRI, CRN

Quotation text

This page intentionally left blank.

82

16

CR, CRI, CRN

Further product information

16. Further product information


WebCAPS
WebCAPS is a Web-based Computer Aided Product
Selection program available on www.grundfos.us.
WebCAPS contains detailed information on more than
220,000 Grundfos products in more than
30 languages.
Information in WebCAPS is divided into six sections:
catalog
literature
service
sizing
replacement
cad drawings.

Catalog
Based on fields of application and pump types, this section
contains the following:
technical data
curves (QH, Eff, P1, P2, etc.) which can be adapted to the
density and viscosity of the pumped liquid and show the
number of pumps in operation
product photos
dimensional drawings
wiring diagrams
quotation texts, etc.

Literature
This section contains all the latest documents of a given pump,
such as
data booklets
installation and operating instructions
service documentation, such as service kit catalog and service
kit instructions
quick guides
product brochures.

Service
This section contains an easy-to-use interactive service catalog.
Here you can find and identify service parts of both existing and
discontinued Grundfos pumps.
Furthermore, the section contains service videos showing you
how to replace service parts.

83

16

CR, CRI, CRN

Further product information

Sizing

This section is based on different fields of application and


installation examples and gives easy step-by-step instructions in
how to size a product:
Select the most suitable and efficient pump for your
installation.
Carry out advanced calculations based on energy,
consumption, payback periods, load profiles, life cycle costs,
etc.
Analyze your selected pump via the built-in life cycle cost tool.
Determine the flow velocity in wastewater applications, etc.

Replacement
In this section you find a guide to selecting and comparing
replacement data of an installed pump in order to replace the
pump with a more efficient Grundfos pump.
The section contains replacement data of a wide range of pumps
produced by other manufacturers than Grundfos.
Based on an easy step-by-step guide, you can compare
Grundfos pumps with the one you have installed on your site.
When you have specified the installed pump, the guide will
suggest a number of Grundfos pumps which can improve both
comfort and efficiency.

CAD drawings
In this section, it is possible to download 2-dimensional (2D) and
3-dimensional (3D) CAD drawings of most Grundfos pumps.
These formats are available in WebCAPS:
2-dimensional drawings:
.dxf, wireframe drawings
.dwg, wireframe drawings.
3-dimensional drawings:
.dwg, wireframe drawings (without surfaces)
.stp, solid drawings (with surfaces)
.eprt, E-drawings.

WinCAPS
WinCAPS is a Windows-based Computer Aided
Product Selection program containing detailed
information on more than 220,000 Grundfos products
in more than 30 languages.
The program contains the same features and
functions as WebCAPS, but is an ideal solution if no
internet connection is available.
WinCAPS is available on DVD and updated once a
year.
Fig. 20 WinCAPS DVD

84

16

CR, CRI, CRN

Further product information

Grundfos GO
Mobile solution for professionals on the GO!
Grundfos GO is the mobile tool box for professional users on the go. It is the most comprehensive platform for mobile
pump control and pump selection including sizing, replacement and documentation. It offers intuitive, handheld
assistance and access to Grundfos online tools, and it saves valuable time for reporting and data collection.

GET IT ON

Subject to alterations.

85

86

87

Copyright Grundfos Holding A/S

98446676 0414
ECM: 1134614
Grundfos Kansas City
17100 West 118th Terrace
Olathe, Kansas 66061
Phone: 913-227-3400
Fax: 913-227-3500
www.grundfos.us

Grundfos Canada
2941 Brighton Road
Oakville, Ontario L6H 6C9 Canada
Phone: +1-905-829-9533
Fax: +1-905-829-9512
www.grundfos.ca

Grundfos Mxico
Boulevard TLC No. 15
Parque Industrial Stiva Aeropuerto
C.P. 66600 Apodaca, N.L. Mexico
Phone: 011-52-81-8144 4000
Fax: 011-52-81-8144 4010
www.grundfos.mx

The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S or Grundfos A/S, Denmark. All rights reserved worldwide.

L-CR-PG-001

You might also like