Professional Documents
Culture Documents
Installation Guide
Package Contents
IN
P+
D
OU ATA
T
ER
ER
POW
IN
P+
D
OU ATA
T
Mounting bracket
POW
DA
TA
IN
DA
TA
IN
Product Overview
1 Power: Power LED will remain lit while power is applied.
2 Signal strength: Indicate receive signal strength.
The Signal Strength LEDs are only used at the
power on to assist the installation.
The CPE will turn off all the Signal Strength LEDs after a
timer expires from power on. Such design is to prevent
the outdoor CPE becoming a potential target particularly
at night. The default time is 60 minutes however,
is user settable in the web GUI.
2 3
5 6
Note:
For optimum reception, there are few things you should consider before
installation. Please see Appendix 2 for important installation considerations.
Be sure that one of the cables used is an outdoor grade CAT 5e (or above)
Ethernet cable type and the length of the cables are adequate to reach the
location of the CPE and indoor PPoE.
Prepare wrenches
Prepare adjustable wrenches or four combination wrenches
(size: 13mm x 2, 8mm x 1, and 19mm x 1)
Warning:
1. Do NOT start any traffic test (ex: throughput
test and internet browsing) before the
1
installer returns to the ground.
2. Do ground the CPE to provide protection
from ESD (electrostatic discharges) and lightning.
SIM card
Kit-1
Quantity: 1
22
Kit-3
Quantity: 1
13
16
7.9
Washer (M8)
Quantity: 1
Kit-4
Quantity: 1
7.9
M8 Hexagon Nuts
Quantity: 2
13
Kit-2
Quantity: 1
Washer M8x22
(OD) mm
Quantity: 2
27
M13 Washer
Quantity: 2
18.72
13.5
M8 Spring Washer
Quantity: 3
8.9
Spring Washer
(M5)
Quantity: 6
12.7
Washer (M5)
Quantity: 4
21.6
M13 Spring
Washer
Quantity: 2
Wall-mount Assembly
Step 1: Align the mounting bracket on the wall. Using the bracket as
mounting template, mark the positions to drill the holes.
Step 2: Assemble the bracket as shown in the illustration.
C
D
E
G
Step 1.
A
Step 2.
G
C
J
I
K
L
Step 3.
Step 4: Hang the CPE to the wall and secure the bracket using the designated
screws and washers.
4
Pole-mount Assembly
Step 1: Align the mounting bracket on the wall. Using the bracket as
mounting template, mark the positions to drill the holes.
Step 2: Assemble the bracket as shown in the illustration.
C
D
E
G
Step 1.
A
Step 2.
G
C
J
I
K
L
Step 3.
Step 4: Align a pole on the bracket and assemble the pole bracket as shown.
Step 5: Adjust the CPE position to an appropriate direction and secure the pole
bracket using the designated screws and washers.
P
O
Step 4.
O
N
Step 4.
For 1.5 to 2 diameter
Connect to PC
Prepare two Ethernet cables for connection.
Step 1: Insert the other end of the Ethernet cable to P+D OUT port of the
PoE adapter.
Step 2: Connect another Ethernet cable to a Network Hub/Router or directly
to PC/Laptop via PoE adapter (Data/IN port).
Step 3: Plug the PoE adapter to an electrical outlet.
Electrical outlet
Step 3
LTE Outdoor CPE
PC/Laptop
PoE
R IN
POWE
P+DA
TA
OUT
P+D
DATA
IN
/OU
T
Data
/IN
Step 1
Step 2
Network Hub/Router
Electrical outlet
Adapter
LTE Outdoor CPE
Step 3
PoE
R IN
POWE
P+DA
TA
OUT
P+D
PC/Laptop
DATA
IN
/OU
Data
/IN
Step 1
Step 2
Network Hub/Router
Step 2: On the opening screen, enter the username (admin) and password
(admin).
Step 3: Click OK to login to the main screen.
.
Step 4: Click one of the header tabs for advanced features.
E580 series CPE uses network domain 192.168.1. X.
For any downstream connections, all devices should avoid using this
network domain otherwise there might be IP address conflict and cause
communication failure.
Note
If you can NOT connect to the network, please follow below steps to set
APN manually.
1. Go to Network > Mobile Internet > WWAN Setting- APN Profile Setting
to enter the APN profile name, then click Add.
2. Enter APN, User Name, and Password, then click Save.
3. Go to Network > Mobile Internet > WWAN Setting- Network Setting
to configure the APN to Manual. Then select the Profile Name you
added from the Profile Selection, then click Apply.
Above change will be applied after the system is rebooted.
If the PIN verification on your SIM card is enabled, please go to
Network > Mobile Internet > UICC/SIM PIN Management to unlock the
PIN code.
Once the external SIM is reinserted, you must restart the CPE to read the
SIM card properly.
For more detail information, please go to
http://www.bandrich.com/UM/E580_Embedded_Series.pdf
to download User Manual.
9
Appendix 1.
Water-proof RJ-45 cable jack assembly
RJ45 Plug
Seal
Gasket
Housing
Lock Nut
Sealing Nut
40.0(REF)
3.5(REF)
7.7
Cable
Lock Nut
Seal
Plug
10
Appendix 2.
Important Installation Considerations
Before installing the outdoor CPE, consider the appropriate location,
clearance, and device orientation.
Mounting
Choose a solid wall/ground to mount the CPE.
Mount on a wall/pole that can sustain the CPE dimensions and weight.
Mount upright on a vertical surface.
11
Appendix 2.
Position Adjustment
The CPE must be directed towards the nearest base station. By pointing
the CPE in the proper direction ensures that you receive the strongest
signal.
Fine tune the signal by
adjusting the orientation
horizontally or vertically to
increase the CPE signal
strength.
13
Warning:
To receive stronger signal, please do NOT
place your head or body in front of the
CPE while you are positioning the CPE
or checking the signal strength LEDs on
the front panel.
Check the LEDs on the front panel - increasing lighted LEDs indicates
stronger signal.
Access the web management and go to Status > Mobile Network >
Information to view the Rx Signal Strength.
12
68060211011
P/N: 68060211011 Rev.A