Professional Documents
Culture Documents
1. General Introduction
C1306-D is an item of microcomputer instrument used to control humidity. The input and output
function is as follows,
l Humidity Probe(HP)
l Dehumidifying relay K1 (16A 250VAC)
l Humidifying relay K2 (10A 250VAC)
2. Error Status:
1EEE Sensor Error
2PrE Paramter Error. Ener paramter menu to choose dFu, and choose 1 to restore parameter to be
factory set default value. Then reset parameter.
3. LLA Humidity is lower than Lower alarm humidity(LS), and the duration time surpasses alarm
delay( At).
4. HHA Humidity is higher than Upper alarm humidity(US),and the duration time surpasses the alarm
delay(At).
3. 1 Front Panel
Dehumidify
Humdify
Set
SET
C1306-D MANUAL
6. Choose END or if there is no key-pressing in 10 seconds, it will exit from set and return to status
of humidity display.
3.5 How to lock keyboard or remove keyboard locking
1. Press the combination key and for over 3 seconds at the same time to lock keyboard or
remove the keyboard locking.
2. When keyboard is locked, it will display OFF, and it will show ON when the keyboard locking is
removed.
4. Parameter list
Us:
Alarm against upper humidity
Range: 0.1-100%RH, Factory-set value: 100%RH.
Ls:
Alarm against lower humidity
Range: 0-99.9%RH, Factory-set value: 0%RH.
CAL: Sensor compensation. Range: -10-10%RH Factory-set value: 0%RH
HSC: Dehumidifying magnetic hysteresis Range: 0-20%RH Factory-set value: 2.0%RH
HSH: Humidifying magnetic hysteresis Range: 0-20%RH
Factory-set value: 2.0%RH
Dbd: Deadzone, There is no humidifying and dehumidifying output when the humidity is in
between the range: SP dbd/2 ~ SP + dbd/2
Range: -19.9 ~ 20%RH Factory-set value: 0.0%RH
* If dbd is lower than 0, dbd must be higher than 2(-HSC + 1) and 2(-HSH + 1)
rt: The minimum close time of the instrument Range: 0-255minutes, Factory-set value0
minute.
At: Humidity alarm delay Range: 0-255 minutes, Factory-set value: 60 minutes
C-H: Working mode, Range:0-2 Factory-set value:0
0 Humidifying and dehumidifying mode
1 Dehumidifying mode
2 Humidifying mode
dFu: Range:0-1
1 Return to factory set
0 No changes
END: Exit to parameter set
Bracket
6. Technical data:
Case Material:
Dimension:
ABS,Black
753870
Page 2/3
WWW.HONGYIINC.COM
C1306-D MANUAL
Mounting
Waterproof
Connection method:
Working Condition:
Storage Condition:
Measurement Range:
Display Accuracy:
Power:
Power Consumption:
Relay
7129.5
Front panel,IP54
Screw
-1055RH85no defrosting
-1070RH85no defrosting
0~100%RH(10~90%RH ,2% Others 3%)
0.1%RH
220VAC,10,50/60Hz
No more than 2W
K1 250VAC 16A
K2 250VAC, 10A
Digital humidity sensor, DHT6X
Three keys
2 channels of always-on relay
3-digit LED
Sensor:
Input:
Output:
Display
Connection Fig.
CONTROLLER
10A(MAX)
250VAC
16A(MAX)
250VAC
HP
K2
1
K1
4
VCC
data
6 4 75
sck
Humi
COM
Dehumid
Power
220VAC/50Hz
Page 3/3
WWW.HONGYIINC.COM
DHT6X
Gnd