You are on page 1of 4

FAQ-0032

Question: Procedure for reading out the fault buffer


Answer:

State 1: LED Strung/Blocked is off


This indicates that the devices is not in blocked mode. Press key "CW" on the operation
panel and enter code word "866315". The display shows . Confirm by pressing key
"E" twice.
Now press the key DA and enter the address 9802. This has to be confirmed by pessing key
E once. The display shows the following text:
9802 MONITOR START ?
Quit the operation mode with J/Y. The display shows:
MONITOR- START INTEGR. OPERAT.
In this mode, the protection functions are blocked. The life contact is energized, i.e.the device
failure is indicated in this mode. Continue with section "instruction".

State 2: LED Strung/Blocked is on


This means that the devices is in blocking mode. The display shows the following text:
MONITOR START- FAILURE PROCESSING
or
MONITOR START- WRONG ORDER CODE
This is also indicated by the red LED Strung/Blocked.

Instruction:
Press key "CW" on the operation panel for several seconds. Enter code word "333333",. The
display shows . Confirm by pressing key "E" twice.
Scroll up in the functions selection using the bold arrow key until reaching the function
FUNCTION CHOICE ERR. BUF.. Then operate key "E" two times. Scroll with the bold
arrow keys through the individual failure indications, select the information of each failure
number with the thin arrow keys and note it in the following table. Return to the functions
selection by operating key "R".
Datum

2002-02-26

Bearb.

Keyler

Gepr.

Schick

FAQ-0032
Blatt

SIEM ENS AG
P T D PA D C C
1A
Zust

Erstausgabe
Mitteilung

2002-02-26
Datum

Key
Name

Power Transmission and


Distribution

SIEMENS AG Alle Rechte vorbehalten All rights reserved

C53000-A2000-X0032-1A-7620

1/4

Please send the content of the fault buffer or the following table ( Sheet-No. 3 ) to
SIEMENS AG Nrnberg
Services- PTD
Fax:

0180/524-2471

Email: services@ptd.siemens.de

Return to operating mode:


Due to the last entries the relay is in a circulating menu. Either the bold arrow key up or the
bold arrow key down has to to be pressed until the disolay shows:
"FUNCTION CHOICE START"
or
"FUNCTION CHOICE ORIGINAL START"
As a minimum a "START" is necessary. The start function keeps all settings and
annunciations of the relay. Choose "FUNCTION CHOICE START" and press 1 "E" once. The
device returns to the operating mode after a short time.
If initially the red LED "Strung/Blocked" had been on on, it could be necessary to initiate an
ORIGINAL START. Confirm this by pressing "E" once and enter the codeword "333333".
Afterwards press "E" twice. The display shows "ORIGINAL START BEGIN". After a few
seconds the device returns to the operating mode. In consequence of this procedure all
settings and annunciations were lost. Therefore the parametrization must be transferred
again from the pc to the relay or changed to the feeder-specific data by using the front panel.

Datum

2002-02-26

Bearb.

Keyler

Gepr.

Schick

FAQ-0032
Blatt

SIEM ENS AG
P T D PA D C C
1A
Zust

Erstausgabe
Mitteilung

2002-02-26
Datum

Key
Name

Power Transmission and


Distribution

SIEMENS AG Alle Rechte vorbehalten All rights reserved

C53000-A2000-X0032-1A-7620

2/4

customer: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

station: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

contact: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

phone: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

fault

reaction

no

function

local indication

info 0

info 1

time

date

no

01:
02:
03:
04:
05:
06:
07:
08:
09:
10:
11:
12:
13:
14:
15:
16:
17:
18:
19:
20:

ORDER CODE: 7 _ _ _ _ _ _ - _ _ _ _ _ - _ _ _ _ / _ _

firmware version: V _ _._ _ _

fabrication no: BF _ _ . _ _ - _ _ _ _

date of delivery: _ _ . _ _ . _ _ _ _

How did the protection device get in the monitor mode, i.e. by switching the CB, during change of settings
Or anything else ?_____________________________________________________________________________
Datum

2002-02-26

Bearb.

Keyler

Gepr.

Schick

FAQ-0032
Blatt

SIEM ENS AG
P T D PA D C C
1A
Zust

Erstausgabe
Mitteilung

2002-02-26
Datum

Key
Name

Power Transmission and


Distribution

SIEMENS AG Alle Rechte vorbehalten All rights reserved

C53000-A2000-X0032-1A-7620

3/4

Warnings
!

WARNING
Dangerous voltages may occur in devices and modules during operation depending on the
design and application. Incorrect use of these devices can therefore result in severe personal
injury or substantial damage to property.
Only suitably qualified staff should work on this device.
Correct and safe operation of this device is dependent on proper handling, installation,
operation and maintenance.
Should you require further information, or should particular problems occur which are not
handled in sufficient depth in the Instructions, help can be requested through your local
Siemens Office or representative.

QUALIFIED PERSON
A "qualified person" is one who is familiar with the installation, construction and operation of the device and who
has the appropriate qualifications, e.g.
is trained and authorised to operate and maintain devices/systems in accordance with established safety
practices for devices with electrical circuits.
is trained in the proper care and use of protective equipment in accordance with established safety
practices.
is trained in first aid.

Subject to change without prior notice !

Datum

2002-02-26

Bearb.

Keyler

Gepr.

Schick

FAQ-0032
Blatt

SIEM ENS AG
P T D PA D C C
1A
Zust

Erstausgabe
Mitteilung

2002-02-26
Datum

Key
Name

Power Transmission and


Distribution

SIEMENS AG Alle Rechte vorbehalten All rights reserved

C53000-A2000-X0032-1A-7620

4/4

You might also like