You are on page 1of 4

A320TECHNICAL TRAINING MANUAL

TRAINING & FLIGHT OPERA TIONS SUPPORT DIVISION

AIRBUS INDUSTRIE

31- INDICATING/RECORDING SYSTEMS

1- 0n which displays are the engine parameters?


A PFD .
B ND .
CE/W.

2- What do the visual attention getters consist of ?


A A red and an amber light below the E / W display.
B A red and an amber light in front of each pilot.
C A message displayed on PFD 1.

3- Which computer processes the warnings?


A SDAC
B FWC
C DMC

4- What is the basic role of the DMCs?


A They compute and generate displays.
B They generate audio warnings.
C They generate amber warnings.

5- What happens if one FWC fails ?


A All the warnings are lost.
B Only red warnings are lost.
C No warnings are lost.

6- What happens if DMC 1 fails?


A DMC 3 automatically replaces DMC 1.
B DMC 3 must be manually transferred.
C Nothing.

7- The STS reminder is displayed on:


A The STATUS page.
B The ENGINE WARNING display.
C All the system pages.

8- Which system page is normally displayed when the A/C is on the ground with both
engines shut down?
A ENGINE page
B DOOR/OXY page
C ELEC page

A320TECHNICAL TRAINING MANUAL


TRAINING & FLIGHT OPERA TIONS SUPPORT DIVISION

AIRBUS INDUSTRIE

31- INDICATING/RECORDING SYSTEMS

9- ON which display does the warning message appear?


A System display.
B Engine and warning display.
C STATUS display.

10- What happens if the RCL pushbutton is pressed?


A Warnings are inhibited.
B The STATUS page is displayed.
C The warnings are recalled.

11- What is displayed on the STATUS page?


A MEMO messages.
B Operational status messages.
C Warning messages.

12- Which ECAM page is displayed in cruise?


A ENGINE page.
B FLT/ CTL page.
C CRUISE page.

13- Which ECAM page is displayed when the landing gear is selected down in phase 6, ?
A WHEEL page.
B CRUISE page.
C FLT/ CTL page.

14- How is an advisory mode indicated?


A It is indicated by an audio warning.
B It is indicated by MASTER CAUTION flashing.
C The drifted parameter pulses on the ECAM display.

15- What does the link between DMC and DUS consist of ?
A An ARINC 429 high speed data bus.
B Two high speed data buses called DSDLs, one of being used as a feedback.
C Three ARING 429 data buses.

16- What does the link between FWCs and DMCs consist of ?
A An ARINC 429 bus and RS 422 message bus.
B Discrete signals.
C Two ARINC 429 data buses.

A320TECHNICAL TRAINING MANUAL


TRAINING & FLIGHT OPERA TIONS SUPPORT DIVISION

AIRBUS INDUSTRIE

31- INDICATING/RECORDING SYSTEMS

17- What does it mean when xx is displayed amber on a DU instead of a numeric value?
A The temperature indicated is too hot.
B The value is a negative number.
C The parameter is not correctly received.

18- The clock provides UTC to:


A: Only the two FMGCs.
B: The CFDIU, FDIU and the two FMGCc.
C: Lower ECAM display.

19- The POST FLIGHT REPORT is made up from:


A Only the LAST LEG ECAM REPORT.
B The LAST LEG ECAM REPORT and the LAST LEG REPORT.
C Only the LAST LEG REPORT.

20- Which action must be taken by maintenance personnel when a class 1 failure affects
an aircraft system?
A Refer to MMEL to know if the failure is a Go, no G0 or GO IF item.
B Do not refer to the MMEL.
C Nothing as the failure can be left uncorrected until the next scheduled Maintenance check.

21- When does a class 3 failure have to be corrected ?


A Immediately because it has operational consequences .
B Before next flight.
C The corrective action can wait until the next scheduled maintenance check.

22- In flight, a class 2 failure has occurred. Now, we are on ground. Where is this failure
displayed?
A Only on the ECAM status page.
B On the LAST LEG REPORT, the AVIONIC STATUS and the ECAM status page.
C Class 2 failures are only displayed in flight.

23- Which centralized Fault Display system functions are available in flight?
A LAST LEG REPORT and LAST LEG ECAM REPORT
B AVIONICS STATUS, LAST LEG REPORT, SYSTEM REPORT/TEST
C CURRENT LEG REPORT, CURRENT LEG ECAM REPORT

A320TECHNICAL TRAINING MANUAL


TRAINING & FLIGHT OPERA TIONS SUPPORT DIVISION

AIRBUS INDUSTRIE

31- INDICATING/RECORDING SYSTEMS

24- When you make a print of the PREVIOUS LEGS REPORT?


A You print only the page displayed on the multipurpose control and Display Unit, even
if the report contains several pages.
B You print all the report, even if it contains several pages.
C You print the sum of the failure data delivered by the BITEs and the warning messages
delivered by the ECAM.

25- Which Centralized Fault Display System functions are available in BACK- UP mode,
on ground?
A None.
B SYSTEM REPORT/TEST for MAIN systems.
C LAST LEG REPORT and LAST ECAM REPORT

26- When is the LAST LEG REPORT transferred to the REVIOUS LEGS REPORT?
A At Electrical power on.
B At 1 ST engine start.
C After take-off.

27- What happens when the GND/CTL pushbutton is pressed on ground?


A The recorder starts but only if engines are running.
B The recorder starts.
C The recorder does not start.

You might also like