Professional Documents
Culture Documents
EXPORT CONTROLLED
General
Remove, clean and install the Pc filter, which is bracket mounted to the gearbox. (See Figure 201,
730000.)
2.
Replacement
A.
Removal
(1)
Remove the scrolltoPc filter Pc line by disconnecting the line at both ends. Hold the filter
assembly by placing the proper size wrench on the large hex flats of the housing or filter
element while loosening the coupling nut.
(2)
Disconnect the Pc air tube from the aft end of the filter. Hold the filter assembly as outlined
above while loosening the coupling nut.
Remove the nut and bolt securing the filter clamp to filter mounting bracket. Remove the
filter and separate the clamp from the filter.
1.
2.
Filter element
Packing
3.
Filter housing
Pc Filter Assembly
Figure 201
732003
Page 201
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
Jul 1/95
RollsRoyce
EXPORT CONTROLLED
3.
Installation
(1)
Assemble the clamp on the filter and secure it to the filter mounting bracket with a bolt and
nut. Tighten the nut to 3540 lb in. (3.94.5 N.m). Make sure that the arrow on the filter is
pointed rearward.
(2)
Attach the air tubes on both ends of the filter. Hold the filter with the proper wrench at the
hex flats of the filter assembly while tightening the coupling nuts to 80120 lb in. (9.013.6
N.m).
B.
Disassembly
(1)
Remove the lockwire and separate the filter element and packing from the filter housing.
(See Figure 201, this section.)
(2)
When a vise is used, place the element hex (1) in the vise and use a wrench on the hex of
the housing (3).
(2)
Cap the outlet fitting of the element with a clean metal cap (AN 8204 or equivalent).
(b)
(c)
Remove the cap and blow dry the element. Use clean, dry lowpressure air,
100120 psig (689827 kPag), in a reverse flow direction (through the outlet fitting).
732003
Page 202
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
Jul 1/95
Rolls--Royce
EXPORT CONTROLLED
C.
(b)
(c)
Blow dry the element. Use clean, dry low--pressure air, 100--120 psig (689--827
kPag), in a reverse flow direction (through the outlet fitting).
(d)
Immerse the element in a neutralizing solution of phosphoric acid (50% acid, 50%
water) at 21C (70F) for 5 minutes.
(e)
(f)
Blow dry the element. Use clean, dry low--pressure air, 100--120 psi (689--827
kPa), in a reverse flow direction (through the outlet fitting).
Inspection
Inspect the filter assembly for dirt or damage. Replace unserviceable filters.
D.
Assembly
(1)
Apply high temperature lubricant (Never--Seez or equivalent) lightly to the threads; then,
assemble the packing and housing over the filter element.
(2)
When a vise is used, place the element hex in the vise and use a wrench on the hex of the
housing. If a metallic seal is used, tighten to 60--65 lb ft. (81--88 N.m). If a rubber seal is
used, tighten to 150--175 lb in. (16.9--19.8 N.m). Secure with lockwire.
73--20--03
.2007 Rolls--Royce Corporation
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
Page 203
Jul 1/07
EXPORT CONTROLLED
RollsRoyce
732003
Page 204
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
Jul 1/02