Professional Documents
Culture Documents
no.
912-100-0453
page
1/7
Content:
1
2
3
4
5
6
7
8
Safety advises
Usage
Construction of the DRG 1200
Function
Installation, dimension and hole pattern
Technical data
Characteristic curve
Validation
AURORA
Konrad G. Schulz GmbH & Co. KG
Tel.: 0 62 84 / 92 02-0
info@aurora-eos.com
www.aurora-eos.com
The information on this document and the copyrights are ownership of
AURORA Konrad G. Schulz GmbH & Co. KG, Joachim Schulz Str. 4, D-69427 Mudau.
Transmission or duplication of this document or the utilization of the contents are not allowed without the
agreement of AURORA Konrad G. Schulz GmbH & Co. KG otherwise it is explicit allowed. Violation will be
prosecuted. All rights of patents, industrial designs and trademarks are reserved.
Please pay attention to ISO 16016.
- we reserve the right to make technical modifications -
established: 11.01.07 KH
checked:
date/name
date/name
a) 14197 05.11.08 KH
b) 14718 18.02.09 KH
approved:
date/name
c) 17385 21.07.11 KH
d) 19627 29.01.13 KH
Technical Information
no.
912-100-0453
page
2/7
part no.:
131-601-0100 DRG 1200 12V basic version
131-602-0100 DRG 1200 24V basic version
131-601-0101 DRG 1200 12V 1-speed
131-602-0101 DRG 1200 24V 1-speed
131-601-0102 DRG 1200 12V 2-speed
131-602-0102 DRG 1200 24V 2-speed
131-601-0103 DRG 1200 12V 3-speed
131-602-0103 DRG 1200 24V 3-speed
131-602-0200 DRG 1200 24V 4-speed
other versions optionally
Safety advises
The blower is principle maintenance- and service-free. If there is maintenance work to do, make
sure it is to be carried out only when the motor is not running. In order to avoid injuries, the blower
is to be separated from the current circuit.
Make sure that maintenance work is only carried out by specialised personnel.
Do not reach into the blower and never stick objects into it.
Please do not get into contact with the resistor on the blower, if it has not completely cooled down.
Advice for installation and maintenance work:
The rules for the prevention of accidents as well as other recognises technical and labour medical
security regulations must be observed.
2.
Usage
The twin radial blower DRG 1200 is used for powerful usage in heaters, A/C units and ventilation systems.
3.
3.1. Parts
The twin radial blower DRG 1200 consists of the following parts
- motor, radial wheels, inner and outer rings = fan unit
- basic plate, half bowl, outer rings, motor holder
- Dropping resistor with micro-temperature-fuse MTS for versions with several speed level, clip
- housing clips, 2 screws
- cables
Optional with suppressor module
Information about the suppressor module can be seen in technical information 912-100-0398.
Technical Information
no.
912-100-0453
page
3/7
3.2. Material
The housing lower part is made out of plastic granulate polyamide PA6 GK30.
Housing upper part, motor holder, inlet rings and the wheels are made out of plastic granulate polyamide PA6, 35% glass-fibre-reinforcement.
This material is has a high temperature-resistant and because of the glass-fibre-reinforcement a high
stability. A safety data sheet about the granulate can be ordered by AURORA.
3.3. Speed control
The blower can be delivered in 1-speed-, 2-speed- or 3-speed level versions. (option: 4-speed)
Caution! The vehicle side fuse protection of 15 A at 24V or 30A at 12V has to be made
by the customer.
See circuit diagram blower.
The different blower speed are achieved using a dropping resistor. The dropping resistor is a cemented ceramic resistor.
The blower is protected from overload and a possible burning danger with a micro-temperature- fuse
(MTF) installed at the resistor.
3.4 cables
The used wires are unscreened low tensions wires with thin-wall isolation for road vehicles.
FLRY with colour marking of wires according to DIN IEC 304.
Technical Information
4.
no.
912-100-0453
page
4/7
Function
The air enters axial into the fan wheels, then the air will be radial turned round and leaves on the area
vertical to the suction direction.
Note: the blower carbon brush is a wearing part. If the carbon brushes are outworn, defective or contaminated, the motor will not run or not in a suitable way.
At any service interval (depending on usage situation) the blower function has to be checked and the
blower has to be changed, if necessary.
The check of the blower in a disconnected state:
optical check on
- physical damage on the housing, the air grille or the fan wheel
- contamination, dust, corrosion and other, that impair the function
stiffness
5.
Dimensions:
Technical Information
no.
912-100-0453
page
5/7
Hole pattern:
Installation instructions:
For reliable operation of the DRG, the maximum fan bracing of 1 mm are not exceeded. Provision
shall be made for a suitably flat mounting surface.
to illustrate:
no.
912-100-0453
Technical Information
6.
Technical data
speed 1
470
277
70
56
speed 2
800
471
150
68
speed 3
1250
736
307
77
7. Characteristic curve
page
6/7
Technical Information
no.
912-100-0453
page
7/7
Standard basis
power measuring
Sound intensity level test
dust test
AU standard
Short description
Validation
963-38T-0010
characteristics OK
963-38T-0011
OK
963-38T-0003
OK
vibration test
963-38T-0007
OK
OK
DIN 50021
963-38T-0016
OK
963-38T-0012
start-up test
over voltage 32V 60 min
polarity test
Insulation test/electric strength 500V
run behaviour with resistor
OK
OK
OK
OK
balance quality
blower balanced
OK
DIN IEC 68
OK
DIN IEC 68
DIN IEC 68
72h at 85C
500h at 80C
OK
IVECO 18-2105
OK
DIN IEC 68
OK
DIN IEC 68
OK
DIN IEC 68
OK
cold test
DIN IEC 68
OK
arctic test
MAN LH 259001
OK
EMC tests
2006/28 EC directive
OK
electrostatic discharge
OK
ca. 5000 h
laboratory conditons
lifetime test
963-38T-0008