You are on page 1of 24

ACCESS TECHNOLOGIES

C-107, Kailas Industrial Complex, Hiranandani Link Road,


ACCESS
Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964
PRODUCT LIST 2017
E-mail : info@accesstech.co.in Website : www.accesstech.co.in

Dear Sir,
We are pleased to quote below the products supplied by us. Kindly refer to page no. 2 to 23 for details and rates
of products and page no. 24 for terms and conditions of supply.

VOLTAGE STABILIZERS MULTIMETERS TONG TESTERS C & LCR METERS FUNCTION GENERATOR SIGNAL GENERATOR
& CVT (SINE SQUARE)

Page: 2 Page: 3 Page: 4 Page: 4 Page: 5 Page: 5

PH METER CONDUCTIVITY METER POWER SUPPLIES RESISTANCE METER HIGH VOLTAGE OIL TEST SET
(DC REGULATED) (micro ohm/milli ohm/ ohm/ BREAKDOWN &
kilo ohm meters) (FLASH TESTERS) RELAY TEST SET

Page: 6 Page: 6 Page: 7 Page: 8 Page: 8 Page: 8

LOAD BANKS RPM METERS LUX METER ANEMOMETER & DIGITAL FLUX METER DIGITAL MOISTURE METER
LAMP / R / L / C BANKS (TACHO METERS) (LIGHT INTENSITY METER) SOUND LEVEL METER & THERMO-HYGROMETER
(1 & 3 PHASE )

Page: 8 Page: 9 Page: 10 Page: 10 Page: 10 Page: 10

SOLDERING & DIGITAL INSULATION THERMOMETER MEGGER & TEMPERATURE SMPS


DESOLDERING SOLUTIONS TESTER (Megger) & (Non Contact Type) EARTH TESTER CALIBRATORS & SIMULATORS MODULES & SUPPLIES
DIGITAL EARTH TESTER

Page: 11 Page: 12 Page: 12 Page: 12 Page: 13 Page: 13

TEMPERATURE INDICATORS ANALOG METERS AC/DC POWER SUPPLY DIGITAL PANEL METERS LCR DECADE BOXES VARIACS
CONTROLLERS & SENSORS OHM METERS (SER & PAR) & BAT ELIMINATORS & PORTABLE METERS & RHEOSTATS (DIMMERSTATS)
(AUTO TRANSFORMERS)

Page: 14 Page: 15 Page: 15 Page: 16 Page: 17 Page: 18

TRAINERS ACCESSORIES PROTECTION RELAYS & TRANSFORMERS BATH IMPREGNATING M/C


STARTERS (AC & DC) (SINGLE / THREE PHASE) & BATTERY CHARGER
TERMS
AND
CONDITIONS
OF SUPPLY
Page: 19, 20, 21, 22 Page: 22 Page: 23 Page: 23 Page: 23 Page: 24

Products for : Industries, Laboratories, Railways, Defence, Colleges, R & D, Computers, Offices, Communications, Medicals, etc.

Full details visit our website : www.accesstech.co.in


SERVO CONTROLLED CVT
VOLTAGE STABILIZERS (CONSTANT VOLTAGE TRANSFORMER)

1 KVA ACCESS VS1 250 VA ACCESS CVT250


2 KVA ACCESS VS2 500 VA ACCESS CVT500
3 KVA ACCESS VS3 1 KVA ACCESS CVT1000

Higher Capacity Available Higher Capacity Available


ACCESS VS Series of servo controlled voltage stabilizers are suitable At times a stabilizer is not enough, as a stabilizer can correct voltage with a
for computers, computer peripherals fax machines, EPABX systems, certain finite speed, due to which the short spikes, short interruptions & dips,
telex, photo-copiers, office automation products, telecommunication voltage surges, glitches, transients, noise etc cannot be corrected by a
systems, bio-medical equipments, microprocessor based equipments, stabilizer. Also CVT provides actual isolation.
CNC machines, electronic typewriters, photo processing labs, testing
labs, production lines, moulding machines, TV sets, VCRs, DVD FIELDS OF APPLICATION :
players, air conditioners, transmitters, cable TV control rooms, signaling Computers, Data Processing equipment, Colour Photography Labs, Bio-
equipment, PA systems, radars, scientific apparatus, chemical labs, medical equipment, PA equipment, Telecommunication, TV, VCD/DVD
safety alarms, cash registers, weighing machines, test controls & recorders & players, Teleprinters, Fax machines and all other sensitive
measuring systems, analytical equipments and many other electronic devices.
applications. RECOMMENDATIONS
VS1 is also suitable for 1 computer + printer + monitor. Keep magnetic storage and display devices like Diskettes, Spools, Monitors etc.
VS2 & VS3 are also suitable for 1 &1.5 tons air conditioners away from the CVT. Switch on the CVT before switching ON the attached
peripherals and while switching off, switch OFF attached peripherals first and
OUTPUT VOLTAGE : Output 230V +1% for i/p voltage 170 to 270 volts. then the CVT. Avoid using the CVT for high inductive loads
Safe computer operating o/p between 200 to 250V for i/p 150 to 290V. INPUT VOLTAGE : 180 V 260 V AC
OUTPUT REGULATION: Better than 2% for input variation from LINE FREQUENCY : 50 Hz
170 to 270 volts and load variation from no load to full load. OUTPUT VOLTAGE : 220 230 V 1%
VOLTAGE STABILIZATION RESPONSE: 30 Volts / second. OUTPUT STEP LOAD RESPONSE : 2 cycles (30 to 40 milliseconds)
FULL LOAD EFFICIENCY: Better than 95% EFFICIENCY : 90% (approx) under full load conditions
OUTPUT WAVE FORM : Sinewave
NO LOAD LOSS: 5% of rated capacity. WAVEFORM DISTORTION : 5% (approx) under full load conditions
RECOMMENDED POWER FACTOR: 0.8 to 1. LOAD POWER FACTOR : 0.75% lag to 0.9% lead
INDICATIONS : Mains ON, Under Voltage, Over Voltage, Voltmeter AMBIENT TEMPERATURE : -10C to 50C
to read output voltage TRANSFORMER TYPE: Ferro-Resonant
REAR PANEL CONTROLS : EFFECT OF FREQUENCY: 1.6 (approx) change in output voltage for every
1. Three suitable 3 pin sockets for output. 1% change in line frequency
2. Overload / short circuit protection fuse for VS1, VS2, VS3 INDICATIONS : Mains On, Voltmeter to read output voltage
PROTECTION : Fuse for Overload / short circuit protection
SIZE & WEIGHT (approx) :
ACCESS VS1 : 145mm (H) x 145mm (W) x 245mm (D), 5Kgs SIZE & WEIGHT (approx) :
ACCESS VS2 / VS3 : 200mm (H) x 220mm (W) x 290mm (D), 14Kgs ACCESS CVT250 : 145mm (H) x 145mm (W) x 245mm (D), 6Kgs
ACCESS CVT500 : 200mm (H) x 220mm (W) x 290mm (D), 10Kgs
STANDARD ACCESSORIES : Operation manual ACCESS CVT750 : 200mm (H) x 220mm (W) x 290mm (D), 13Kgs
ACCESS CVT1000: 215mm (H) x 220mm (W) x 410mm (D), 16Kgs
STANDARD ACCESSORIES : Operation manual.

WATTAGE / POWER REQUIREMENTS (An approximate wattage is given for reference)


WATTAGE REQUIREMENTS OF COMPUTERS AND PERIPHERALS: PC with 14/15 monitor (300W), PC with 17 monitor (400W), Dot matrix printer
(100W), Laser printer (500 to 1000W). Inkjet / DeskJet printer (100W), Scanner (100W), Xerox machine (1500 to 2000W), Fax machine (250W), Electronic
type writer (50W).
NORMAL POWER REQUIREMENT OF APPLIANCES : Tube light - 80 watts, Fan - 135 watts, Television -200 watts, 165 Liter Refrigerator - 400 watts,
Large Refrigerator - 700 watts, Geyser -2000 to 5000 watts, 1 ton AC - 2000 watts,1.5 ton AC - 2800 watts, 2 ton AC - 3400 watts, Washing machine without
heater -750 watts, washing with heater - 3000 watts.

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-2-
DIGITAL MULTIMETER ANALOG MULTIMETER 4.5 DIGIT TABLE TOP
(3 DIGIT LCD) (with Lid cum Stand ) DIGITAL MULTIMETER

ACCESS 65A ACCESS YX360 TRD ACCESS 8045T

ACCESS 65 A 3.5 digit Digital Multimeter with Large Size LCD ACCESS Yx360 TRD Analog Multimeter 4.5 digit Large LCD display. 30mm H with back light.
display given on angle for better viewing. It measures AC & DC with Lid cum Stand & wrist strap is useful True RMS Benchtop Multimeter with full features
voltages, AC & DC Current, Resistance, Capacitance in various to measure AC & DC voltages, DC and Overload protection. Ideal for education, service
ranges. Continuity buzzer, Diode & Transistor hFE checking, Current, Resistance, Capacitance in as well as manufacturing sector.
polarity, over range & Lo Bat indication. It is provided with a various ranges. Works on 3V battery. FUNCTION RANGE ACCURACY
holster for safety .Works on 9V battery.
DC Voltage 200mV/2V/ (0.05%3 dgt)
Parameter Range Accuracy Remarks Parameter Range Accuracy 20V/200V
DC Voltage 200mV 0.5% 3 digit DC Voltage 0.1/0.25/2.5/10 3%fs 1000V (0.01%5 dgt)
I/p imp : 10MOhm
2/20/200V 0.8% 2 digit Overload protection /50/250/1000V AC Voltage 200mV/2V/ (0.8%80)
1000V 1% 2 digit AC Voltage 10/50/250/ 20V/200V
1.2% 5 digit 4%fs
AC Voltage 200mV I/p imp : 10MOhm 1000V
750V (1.0%50)
2/20/200V 1% 5 digit Overload protection DC Current 50mA/2.5/25m/
750V 1.2% 5 digit Frequency 40-400Hz 250mA(0.25A) 3%fs DC Current 20mA/200mA/ (0.35%10)
DC Current 2/20/200mA 2% 2 digit Overload protection : 200mA/ 2000mA
500mA/250V fuse Resistance 2K/20K/200K/ 2A/20A (0.8%10)
3%fs
20A 2% 10 digit (20A range unfused) 2M/200MW
AC Current 200mA (0.8%80)
AC Current 2/20mA 2% 3 digit Overload protection : Capacitance 10mf range
2A/20A (1.0%50)
200mA 2% 5 digit 500mA/250V fuse Internal fuse
(20A range unfused) Protection
20A 5% 10 digit Frequency 40-400Hz 0.5A / 250V Resistance 200/2K/20K/ (0.1%5)
1% 10 digit
200K/2M
Resistance 200 Ohm
OTHER FEATURES : Lid cum Stand & 20M (0.4%5)
2/20/200K/ Overload protection
1.0% 4 digit Open Circuit Voltage wrist strap, Inbuilt Test Leads with (5%30)
2M Ohm storing space
Capacitance 20nF to 2000mf
20M Ohm 1% 10 digit : 3.2V (Max.)
POWER REQUIREMENT : 3V (1.5 X 2 Frequency 20Hz to 2MHz (1.0%20)
200M Ohm 5% 20 digit Battery)
Capacitance 20/200nF/ 4% 5 digit DISPLAY : Large Analog Meter with Anti- Diode Test Yes
2/20mF parallex scale
SIZE & WEIGHT (approx) : 160mm(L) X Square 50Hz,100,200,300,400, 500, 600,
200mF 4.5% 5 digit 130mm Wave 700, 800,900,1K,2,3,4 & 5k Hz
(W) X 42mm(H) 340gms (approx) Output (Manual selection) 3.3V p-p
OTHER FEATURES : Continuity buzzer, diode & transistor hFE
STANDARD ACCESSORIES: Inbuilt Test Transistor hEE PNP/NPN
checking, polarity, over range & Lo Battery indication Leads, User Manual & Battery
POWER REQUIREMENT : 9 V Battery Continuity Yes
DISPLAY : Large 3 digit LCD display on angle for better Buzzer.
viewing. Overload
SIZE & WEIGHT (approx) :195 mm (L) x 90 mm (W) x 40mm (H), Yes
Protection
215 gms.
STANDARD ACCESSORIES : Test leads, Instruction manual, Input 10M in DC
Battery. Impedance 2M ohms in AC
Operation Manual (Auto for C & freq. ranges)
Max. display 19999
EXTRA ACCESSORIES
POWER REQUIREMENT : AC 220V / 50Hz
Digital meter Probes / Testing Leads SIZE & WEIGHT (approx) : 255mm(L) X 220mm
(Compatible to Models 65A & 8045T) (W) X 100mm(H) 1.4Kg (approx)
ACCESS AL25 STANDARD ACCESSORIES: Manual, Test Leads,
DMM L type Heavy probes Mains Cord.
(4mm shrouded (R+B) to Test Pin (R+B) type)

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-3-
AC CLAMP METER CAPACITANCE METER LCR METER
(TONG TESTER)
0 to 1000 amps
ACCESS 62A ACCESS 56 ACCESS 24

ACCESS 62 A with wrist strap measures AC ACCESS 56 is useful for measurement of capacitance ACCESS 24 is useful for measurement of inductance, capacitance
current, AC & DC voltage, resistance. of polar and non-polar capacitors, mutual capacitance & resistance of components, motors, transformers, coils, chokes,
Provided with Data hold, Continuity check with of windings of motors, transformers, coils, etc and wires and many other products. Useful for industries, laboratories, R
audio & full range protection mutual capacitance of multi core cables. & D organizations, colleges, defense establishments, railways,
Useful for industries, laboratories, R & D organizations, communication centers etc.
Functions Range Resolution Accuracy
communication centers, colleges, defense establish- INDUCTANCE
200A 0.1A 2% 5 digit ments, railways etc.
Range Resolution Accuracy Test
AC Current 1000A 1A 2% 10 digit Frequency
upto 600A RANGE : 0.1 pF to 20,000 F in 9 range of 200pF,
2000pF, 20nF, 200nF, 2F, 200F, 2000F and 20mF . 200mH 0.1mH 3% 5 dgt
3% 5 digit 2mH 1mH
600 to 1000A ACCURACY, RESOLUTION AND TEST FREQUENCY
20mH 0.01 mH
AC Voltage 750V 1V 1% 4 digit 2% 5 dgt 1 KHz
Accuracy Test 200mH 0.1mH
DC Voltage 1000V 0.8% 1 digit Range Resolution Frequency
1V 2H 0.001 H
200W 0.1W 1% 3 digit 0.5% + 20H 0.01H 5% 5 dgt
Resistance 200pF 0.1pF
20KW 10W 1% 1 digit 7 dgt + 0.5pf
Fuse protection is provided.
2nF 1pF 800Hz
CONTINUITY : Buzzer ON resis < 50 25 ohms. CAPACITANCE
DATA HOLD: Memorizes data for all functions 20nF 10 pF
JAW DIAMETER: 50mm (2") Approx 0.5 % + 5 dgt Test
Range Resolution Accuracy Frequency
DISPLAY: 3 digit, 7 segment LCD with over 200nF 100pF
range and low battery indications 2mF 1nf 200pF 0.1pF
POWER REQUIREMENT: 9V battery 2nF 0.001nF
SIZE AND WEIGHT: 235 mm (L) x 102(W) x 42 20mF 10nF 80Hz
mm (H), 240 gms (approx) 20nF 0.01nF
200mF 100 nF 2.5% 5 dgt 1 KHz
STANDARD ACCESSORIES: Test leads, 200nF 0.1nF
2000mF 1F 2% + 5 dgt 8Hz
9V battery, Instruction manual and carrying case 2mF 0.001mF
20000mF 10F 3% +10 dgt 20mf 0.01mF
200mF 0.1mF 100 Hz
TEST LEAD COMPENSATION (ADJUST) : Available by 5% 5 dgt
2000mf 1mF 10 Hz
front panel control.
CHARGED CONDENSOR PROTECTION: Provided with Fuse protection is provided.
fast acting fuse.
DISPLAY: 3 digit, 7 segment large LCD type of 30 mm
height, over range and low battery indications are provided. Range Accuracy Overall
Resolution Protection
POWER REQUIREMENT: 9 V battery .
SIZE AND WEIGHT : 192mm (L) x 97 mm (W) x 40 mm (H). 200W 0.1W
370 gms approx.
2KW 0.001KW 25V DC
STANDARDS ACCESSORIES: Battery, test leads, 0.8% 2 dgt
20KW 0.01KW or
operation manual and box.
ACrms
200KW 0.1KW
20MW 10 KW 1.5% 5 dgt

EXTRA ACCESSORIES DIODE TEST: Displays forward voltage of diodes.


DISPLAY: 3 digit ,7 segment LCD type of 12.5 mm height , over
Digital meter Probes / Testing Leads range and low battery indications are provided.
(Compatible to Models 62A, 56 & 24) POWER REQUIREMENT: 9V battery
ACCESS AL25 SIZE AND WEIGHT: 190 mm (L) x 90 mm (W) x 45 (H), 345gms
approx
DMM L type Heavy probes STANDARD ACCESSORIES: Battery, test leads, operation
(4mm shrouded (R+B) to Test Pin (R+B) type) manual and box.

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-4-
GENERATORS / OSCILLATORS
ANALOG DIGITAL ANALOG
FUNCTION GENERATOR FUNCTION GENERATOR SIGNAL GENERATOR
(Sine, Square, Triangular (Sine, Square, Triangular, Ramp, (Sine & Square)
& TTL pulse ) Sawtooth, Pulses & TTL pulse)
ACCESS FG100 ACCESS FG9 0.1Hz-1MHz TESTRONIX 72
0.1Hz-100KHz ACCESS FG9A 0.2Hz-2MHz 1Hz-1MHz
ACCESS FG10 ACCESS FG9B 0.3Hz-3MHz
0.1Hz-1MHz

FREQUENCY RANGE: 6 / 7 decadic ranges FREQUENCY RANGE: 7 decadic ranges OUTPUT WAVEFORMS:
selectable by Freq. multiplier Switch (coarse) selectable by Range - Push Switch and Coarse Sine and square waves, simultaneously available on
and continuously adjustable dial (fine). Dial & Fine Frequency Controls with LED display for 2 separate connectors
accuracy is 5% 1O. Min. & Max. Frequency
WAVEFORMS (selectable) : Sine, Square, DISPLAY : Digital 7 segment 5 digit display for FREQUENCY RANGE: 1Hz to 1 MHz, selected by
Triangle & TTL pulse output frequency with LED display for Hz & KHz continuously adjustable dial and a 6 step decade
indication control. The dial accuracy is 5% 1O.
OUTPUT AMPLITUDE : 20 V p/p into open
circuit (10V p-p into 50 ohms) with fine control WAVEFORMS (selectable) : Sine, Square, OUTPUT IMPEDANCE:
OUTPUT IMPEDANCE : 600 ohms Triangle & TTL pulse output Ramp and Pulse 600 ohms.
with the help of duty cycle / symmetry control
DC OFFSET : Variable upto + / - 10 V into open OUTPUT AMPLITUDE (SINE WAVE ) :
circuit OUTPUT AMPLITUDE : 20 V p/p into open
circuit (10V p-p into 50 ohms) with Coarse (dB 0 to 30 volts peak to peak into open circuit, selected
MAINS ON / OFF: Switch provided step) and fine control by continuously adjustable control and a 3 step
FUSE: Fuse for protection decade control. The amplitude level is flat within 0.5
ATTENUATOR : 0 to 60dB variable (2X20 dB db over the entire frequency range (To be checked
POWER REQUIREMENT : 230 V +/ - 10% AC, step coarse attenuator and 20 dB fine control) with low capacitance probes and high frequency
50 Hz OUTPUT IMPEDANCE : 50 ohms & 600 ohms oscilloscopes).
ACCESSORIES: 4mm Banana plug to switch selectable
crocodile cable and Instruction Manual DC OFFSET : Variable upto + / - 10 V into open DISTORTION:
SIZE & WEIGHT (approx): 125mm (H) X 225 circuit Less than 0.5 % from 100 hertz to 100 kilo hertz.
mm (W) x 270 mm (D), 2.5 KG
DUTY CYCLE : (Ramp & Pulse) Continuously OUTPUT AMPLITUDE (SQUARE WAVE) :
variable for continuous working 0 to 15 volts peak to peak into open circuit,
FM IN : Available via external input continuously adjustable.
MAINS ON / OFF: Rocker Switch on back
PROTECTION:
panel
Both outputs are short circuit protected.
FUSE: Fuse for protection
POWER REQUIREMENT : 230 V +/ - 10% AC, SQUARE SYMMETRY:
50 Hz Duty cycle of square wave output is continuously
adjustable from 0% to above 70%
ACCESSORIES: BNC to crocodile cable and
Instruction Manual
RISE AND FALL TIME (SQUARE WAVE OUTPUT):
SIZE & WEIGHT (approx) : 105mm (H) X 225 Less than 100 nano seconds. (To be checked with
mm (W) x 270 mm (D), 3.0 KG low capacitance probes and high frequency
oscilloscopes)
EXTRA ACCESSORIES POWER REQUIREMENT: 230 V +/ - 10% AC, 50 Hz
BNC to Crocodile Probes / Leads
(Compatible to Models FG9, 9A & 9B) SIZE AND WEIGHT (approx) : 90mm (H) X 195 mm
(W) x 250 mm (D), 2.2 KG
ACCESS AL50 ` 150/-
Function Generator probe STANDARD ACCESSORIES: 4mm Banana plug to
(BNC (M) to Crocodile (R+B) probes / leads) crocodile lead pair and instructions manual.

4mm Banana plug to Crocodile Probes / Leads


(Compatible to Models FG100, 10 & Tx72)
ACCESS AL55 ` 100/-
Analog Function / Signal Generator probes
(4mm (R+B) to Crocodile (R+B) probes / leads)

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-5-
pH METER CONDUCTIVITY METER

TESTRONIX 511 TESTRONIX 15

TESTRONIX 511 is useful for measurements of pH values / DC mV of Testronix 15 is useful for measuring conductivity of homogeneous
homogeneous electrolytic solutions. Useful for chemical, pharmaceuticals, electrolytic solutions.
cosmetic, rubber industries, water treatment plants, soil testing Useful for chemical, pharmaceuticals, cosmetic, rubber industries, water
laboratories, pollution control departments, agriculture organization, R & D treatment plants, soil testing laboratories, pollution control departments,
organizations, colleges, service centers etc. agricultural organizations, R & D organizations, colleges, service centers
Supplied with detachable glass combination type of electrode, electrode etc.
stand, pH buffer solutions of 4 & 7 pH (for re-calibration). Standardization Supplied with conductivity cell of cell constant 1, cell stand and standard
(7pH) & slope (4pH) adjustment controls are provided on the front panel. conductivity solution. Detachable conductivity cell ensures easy
Self check facility control on front panel enable users to ensure that the pH replacement.
meter is functioning properly. Temperature setting on front panel provides
compensation for different temperatures of solutions. RANGE: 0.01 micro siemens/cm to 199.9 milli siemens/cm in 5 ranges of
pH RANGE: 0 to 14.00pH with resolution of 0.01 pH 20 micro s/cm, 200 micro s/cm, 2 milli s/cm, 20 milli s/cm and 200 milli
MILLI VOLT RANGE: 0 to 1999 mV DC with resolution of 1 mV. pH or s/cm.
mV measurement selection is providing with a front panel control ACCURACY: 3% of range.
ACCURACY: 0.02 pH 2 dgt for pH measurements. RE-CALIBRATION: Front panel control with the help of standard
0.2 2 milli Volts for milli Volts measurements conductivity solution supplied with the meter, helps in easy re-calibration of
SELF CHECK CAL FACILITY: Available with front panel control. the conductivity meter.
Display reads 7.00 0.02 pH to indicate proper function of the pH meter DISPLAY: 3 digit 7 segment bright LED type of 12.5 mm height. Decimal
TEMPERATURE COMPENSATION: 0C to 100C, adjustable point and over range indications are provided.
POWER REQUIREMENTS: 230 10% volts AC, 50Hz
RE- CALIBRATION : STANDARDIZATION for calibration for 7 pH.
SIZE & WEIGHT (approx): 85mm (H) X 195 mm (W) x 240 mm (D),3 KG
SLOPE for calibration for 4 pH, Buffer solution of 4 &7 pH are provided.
STANDARD ACCESSORIES: Conductivity cell of cell constant 1, cell
DISPLAY: 3 digit 7 segment bright LED type of 12.5 mm height.
stand, standard conductivity solution and instruction manual
Decimal point, over range and negative polarity indications provided.
POWER REQUIREMENTS: 230 10% volts AC, 50Hz
EXTRA ACCESSORIES:
SIZE & WEIGHT (approx): 93mm (H) X 195 mm (W) x 240 mm (D), 2 KG
Conductivity cell
STANDARD ACCESSORIES: Glass combination type of pH electrode,
Cell stand
electrode stand, buffer solutions of 4 & 7 pH and instruction manual.
Buffer of 7.00 ms/cm
EXTRA ACCESSORIES
Electrode
Electrode stand
Buffer of 4 pH / 7 pH

PORTABLE pH METER PORTABLE TDS METER


Low cost, Hand held, portable for use in lab or eld in Low cost, Hand held, portable for use in lab or eld in
aquarium, shing industries, Swimming pool, school / aquarium, shing industries, Swimming pool, school /
college laboratory, food & beverages, RO & other college laboratory, food & beverages, RO & other industries.
industries.
TEST: To test / measure TDS (Quality) of water
TEST: To test / measure pH of liquid RANGE : TDS: 0 ~ 9999 PPM.
RANGE : 0.0 to 14.0 pH RESOLUTION : <1000, 1 PPM; Or 1000, PPM; Automatic
RESOLUTION : 0.1 pH shift.
ACCURACY : + 0.1 pH (@20OC / 68OF) ACCURACY : + 2% (@20OC / 68OF)
TYPICAL EMS DEV. : + 0.2 pH TEST TEMPERATURE: 0 to 99OC
BATTERIES : 3 x 1.5V BATTERIES : 2 x 1.5V
SIZE & WEIGHT : 33mm (H) X 180 mm (W) x 62 mm(D), SIZE & WEIGHT : 33mm (H) X 180 mm (W) x 62 mm (D),
120 gms 120 gms
STANDARD ACCESSORIES : Battery, Case, Instruction STANDARD ACCESSORIES : Battery, Case, Instruction
Sheet Sheet

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-6-
DC POWER SUPPLIES

SINGLE VARIABLE OUTPUT DUAL VARIABLE OUTPUTS


(INDEPENDENT AND TRACKING)

0 to 5 Volts, 0 to 2 Amps TESTRONIX 30B 0 to 16 Volts dual, 0 to 2 amps TESTRONIX 35B


0 to 5 Volts, 0 to 5 Amps TESTRONIX 30C 0 to 32 Volts dual, 0 to 2 amps TESTRONIX 93B
0 to 5 Volts, 0 to 10 Amps TESTRONIX 30D 0 to 32 Volts dual, 0 to 5 amps TESTRONIX 93C
0 to 16 Volts, 0 to 2 Amps TESTRONIX 34B OUT PUT VOLTAGES:
0 to 16 Volts, 0 to 5 Amps TESTRONIX 34C Two independent (both positive or both negative or one positive and one
0 to 16 Volts, 0 to 10 Amps negative) output voltages of different values or of same values are available in
TESTRONIX 34D
independent mode of operation.
0 to 32 Volts, 0 to 1 Amps TESTRONIX 92A Two tracking output voltages of equal value and opposite polarities are
0 to 32 Volts, 0 to 2 Amps TESTRONIX 92B available in dual tracking mode of operation.
0 to 32 Volts, 0 to 5 Amps Independent or dual tracking mode is selectable by front panel control
TESTRONIX 92C
The output voltages are continuously adjustable by coarse and fine front panel
0 to 32 Volts, 0 to 10 Amps TESTRONIX 92D controls. Two output voltages are continuously displayed on 2 separate 3
0 to 65 Volts, 0 to 1 Amps TESTRONIX 36A digit meters with accuracy of 0.5% 2 least counts (Meters have 3 digits in
0 to 65 Volts, 0 to 2 Amps TESTRONIX 36B model 93C). Meters have LED displays of 12.5mm height.
0 to 65 Volts, 0 to 5 Amps Output voltages can be floated on any live voltage or any of the terminals of the
TESTRONIX 36C
output voltage can be grounded to get positive or negative voltages.
OUTPUT VOLTAGES: LOAD CURRENT:
The output voltage is continuously adjustable by coarse and fine controls and Load currents of both the outputs are displayed on two separate 3 digit
displayed on 3 digit, LED display of 12.5mm height with accuracy of 0.5% 2 meters with accuracy of 0.5% 2 least counts (meters have 3 digits in model
least counts. (Voltmeters in models 30B/ 30C/ 30D/ 92A / 92B / 92C/ 92D/ 36A/ 93C). Meters have LED type of displays of 12.5mm height. Maximum values of
36B/ 36C have 3 digit displays) output currents can be limited from less than 10% to 100% of full capacity by
Output voltage can be floated on any live voltage or any of the two voltage continuously adjustable coarse and fine controls.
terminals can be grounded to get positive or negative voltage PROTECTION:
LOAD CURRENT: Short circuit and overload protected. Constant voltage, constant current type
Load current is displayed on 3 digit, LED display of 12.5 mm height with of regulation provides constant voltage if load current is less than the current
accuracy of 0.5% 2 least counts. (Current meter in models 30C/ 34C/ 36C limit setting. If load tries to draw more current than the value of current limit
have 3 digit displays). Max value of output current can be limited from less than setting, current becomes constant at the limit setting and output voltage comes
10% to 100% of the capacity by continuously adjustable coarse and fine controls. down to limit the current at the current limit setting value.
PROTECTION: REGULATION: 0.05% from no load to full load and for 10% variations in
Short circuit and overload protected. Constant voltage constant current type of input mains voltage.
regulation provides constant voltage if load current is less than current limit RIPPLES: Less than 3 milli volts rms.
setting. If load tries to draw more current than the value of current limit setting, POWER REQUIREMENTS: 230 10% volts AC, 50Hz. Power
current becomes constant at the limit setting and output voltage comes down to consumption is 1.5 times the multiple of maximum voltage rating with the
limit the current at the limit setting value. sum of the load currents drawn.
REGULATION: 0.05% from no load to full load and for 10% variations in input SIZE & WEIGHT(approx):
mains voltage. 175 mm (H) x 245 mm (W) x 270 mm (D), 5 KG for 35B
RIPPLES: Less than 3 milli volts rms. 255 mm (H) x 255 mm (W) x 300 mm (D), 9.5 KG for 93B.
POWER REQUIREMENTS: 230 10% volts AC, 50Hz. Power consumption 255 mm (H) x 255 mm (W) x 300 mm (D), 13.5 KG for 93C.
is 1.5 times multiple of maximum voltage rating and load current drawn 125 mm (H) x 125 mm (W) x 270 mm (D), 3.5 KG for 15D1V
SIZE & WEIGHT (approx): STANDARD ACCESSORIES: Test Leads & Instruction manual
125 mm (H) x 125 mm (W) x 270 mm (D), 3.5 KG for 30B/ 30C/ 34B/ 92A
135 mm (H) x 195 mm (W) x 270 mm (D), 5 KG for 30D/ 34C/ 92B/ 36A/ 36B
135 mm (H) x 360 mm (W) x 270 mm (D), 9.5 KG for 34D/ 92C
225 mm (H) X 225 mm (W) x 300 mm (D), 14 KG for 92D/ 36C
STANDARD ACCESSORIES: Test Leads & Instruction manual

DUAL TRACKING OUTPUT MULTI OUTPUT POWER SUPPLY


0 to 15 V/1A Dual Tracking
(with 1 voltmeter) TESTRONIX 35
OUTPUT 1 : 0 to 5 Volts / 5 Amp with
TESTRONIX 15D one voltage control
OVERLOAD INDICATIONS : + & - OUTPUT 2 : 0 to 32 Volts / 2 Amp with
OUTPUT VOLTAGE (Tracking) : Coarse & Fine Controls coarse & fine voltage control
SIZE & WEIGHT (approx) : 125 mm (H) x 125 mm (W) x 270 mm (D); 3.5 KG OUTPUT 3 : 0 to +16 Volts / 0.5 Amp with one voltage control (Tracking)
STANDARD ACCESSORIES: Test Leads & Instruction manual DIGITAL VOLT METER : 5V / 32V / 16V / 200 V External (Selectable)
SIZE & WEIGHT (approx) : 135 mm (H) x 360 mm (W) x 270 mm (D); 10 KG
STANDARD ACCESSORIES: Test Leads & Instruction manual.

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-7-
DIGITAL MICRO-OHM METER ANALOG HIGH VOLTAGE (HV) LOAD BANKS
(CONTACT RESISTANCE METER) BREAKDOWN TESTERS LAMP / R / L / C BANKS
(RESISTANCE METER) / (FLASH TESTERS) (1 & 3 PHASE )
(MILLI-OHM METER) (WITH ANALOG METERS FOR KV & mA)

ACCESS 53C (1A max.) 0 to 5KV AC, 0 to 30mA ACCESS 214 LAMP (BULB) LOADS
ACCESS 53D (10A max.) 0 to 10KV AC, 0 to 30mA ACCESS 215 1f 3KW (12A) ACCESS BL1-03
0 to 5KV AC, 0 to 100mA ACCESS 214A 1f 5KW (20A) ACCESS BL1-05
ACCESS 53C (8 Ranges) & 53D (3 Ranges) is suitable (Other ranges available) 3f 3KW (12A) ACCESS BL3-03
for measurements of resistence of cables, wires,
ACCESS High Voltage Breakdown Testers are useful for 3f 5KW (20A) ACCESS BL3-05
transformers*, motor windings**, coils and contact
resistance of switches, connectors, relays and track checking breakdown (flash over) voltages of motors, RESISTIVE (R) LOADS
resistance of PCB etc. transformers, pumps, chokes, coils, switches,
1f 3KW (12A) ACCESS RL1-03
Four terminal measurement system provides connectors, plastics, rubbers, PCB's, insulation
measurements free from errors due to contact materials, electrical and electronic components etc. 1f 5KW (20A) ACCESS RL1-05
resistance and test lead resistances. 3f 3KW (12A) ACCESS RL3-03
DISPLAY : 3.5 digit 7 segment LED display with over TEST VOLTAGE: 0 to 5 KV AC in ACCESS 214 and 3f 5KW (20A) ACCESS RL3-05
range indication. ACCESS 214A ; 0 to 10 KV AC in ACCESS 215
INDUCTIVE (L) LOADS
Test voltage is displayed on wide view analog type of
Measuring Res. Accuracy Test Current 1f 3KW (12A) ACCESS LL1-03
panel meter. Accuracy 5%.
Range 1f 5KW (20A)
53C 53D TRIPPING CURRENT LEVELS : 0 to 30 mA in ACCESS ACCESS LL1-05
214 and ACCESS 215 ; 0 to 100 mA in ACCESS 214A 3f 3KW (12A) ACCESS LL3-03
1999 mW 1mW Tripping current can be set by front panel control.
0.5% 3f 5KW (20A) ACCESS LL3-05
19.99mW 0.01mW 10A DC Leakage current is displayed on wide view analog panel
2 digit 1A DC meter. Accuracy 5% CAPACITIVE (C) LOADS
199.9mW 0.1mW SAFETY FEATURES : When mains supply is turned 1f 3KW (12A) ACCESS CL1-03
1999mW 1mW NA ON, HV remains OFF and is enabled only when push 1f 5KW (20A) ACCESS CL1-05
button ON, on safety probe is kept pressed & only when 3f 3KW (12A)
19.99W 0.01W 0.1A DC NA ACCESS CL3-03
actual value of leakage current is less than the tripping
0.2% current level setting. HT ON indication glows and buzzer 3f 5KW (20A) ACCESS CL3-05
199.9W 0.1W 10mA DC NA
2 digit sounds when HV is ON. HV probe with safety skirt keeps
1mA DC NA operator's hand away from high voltage. Once high ACCESS 1 phase & 3 phase load banks are available
1999W 1W
voltage is tripped, the same remains off until push button for Lamp load, Resistive (R) load, Inductive (L) load &
19.99KW 0.01KW 0.1mA DC NA Capacitive (C) load. Each load bank is complete with
of the high voltage is released and pressed again.
POWER REQUIREMENTS : 230 volts AC, 10 %, 50Hz Ammeter, Voltmeter & Selector switches as required.
POWER REQUIREMENTS : 230 volts AC 10 %, 50 Hz
SIZE & WEIGHT (approx): 95mm (H) x 195 mm (W) x 200, 400, 600 VA in ACCESS 214, 215 & 214A resp. (Other ranges available)
255 mm (D), 3 KG (For 53C) SIZE & WEIGHT (approx): 200mm(H)250mm(W)
133mm (H) x 245 mm (W) x 270 mm (D), 6 KG (For 53D) 290mm(D) ; 12, 14 & 15 Kgs for 214, 215 & 214A resp.
STANDARD ACCESSORIES: 2 pairs banana to STANDARD ACCESSORIES : Instruction manual .
crocodile test leads and instruction manual.
* Transformers of less than 10 KVA rating. EXTRA ACCESSORIES
** Motors of less than 10 HP rating. Extra HV Probe Available at extra cost
EXTRA ACCESSORIES: Test leads available

RELAY TEST SET DIGITAL HIGH VOLTAGE (HV) OIL TEST SET (BDV TESTER)
BREAKDOWN TESTERS (With Oil Cell & Go / No Go Gauges)
(FLASH TESTERS)

50A Relay Test Set ACCESS 231 0 to 5KV AC, 0 to 30mA ACCESS 217 0 to 60 KV AC, ACCESS 225
TEST VOLTAGE: 0-5 KV AC Digital Voltmeter Acc 3% Manual
100A Relay Test Set ACCESS 232 TRIPPING CURRENT LEVELS : The limit of leakage 0 to 60 KV AC, ACCESS 226
current for tripping can be set from front panel control in Motorised cum Manual
steps of 3, 5, 10, 15, 25 & 30 mA . Accuracy 4%
ACCESS 231 & 232 Relay Test Set are completely AUDIO ALARM : Audio alarm (Buzzer) is activated ACCESS 225 & 226 Oil Test Sets for testing of Di-
self contained, portable units for testing various when high voltage (HV) is available electric strength of insulating oils, confirm to IS-6792
voltage & current based relays, protective devises, POWER REQUIREMENTS : 230 volts AC, 10 %, 50Hz They are ideal for on site field & lab use for testing the
electro-mechanical relays, CT, MCB etc. SIZE & WEIGHT (approx) : 135mm(H)360mm(W) breakdown strength of oils used in transformers, switch
240mm(D) ; 10 Kgs gears, bushings, capacitors & electrical apparatus.
STANDARD ACCESSORIES : Instruction manual
(Other ranges available) (Other ranges available) (Other ranges available)

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-8-
TACHO METER (RPM METER)

HAND HELD HAND HELD PANEL MOUNTING


CONTACT TYPE WITH NON CONTACT TYPE WITH SENSOR
ROTARY AND SURFACE TIPS WITH REFLECTIVE TAPE
ACCESS 81N PM
(Meter with Proximity Sensor)
ACCESS 81C ACCESS 81N ACCESS TM 801
(Meter with Digital Tachogenerator)

Proximity Digital
Sensor Tachogenerator

Tachometers are useful for measurements of RPM of motors, mixers, pumps, fans, etc. and surface speeds of conveyor belts
etc. Useful for industries, railways, electricity boards, defense establishments, R & D organizations, communication centers,
laboratories, colleges. Accuracy of 0.05% 1 digit. Sampling rate of 1 sample per second. Quartz crystal controlled time base
provides high accuracy. Auto ranging micro controller based. Various models are available as below:
5 digit bright LED display with memories of last, 5 digit bright LED display with memories of last, METER
highest and lowest reading. 60 to 50000 RPM highest and lowest reading. 60 to 100000 5 digit bright LED display of 12.5 mm height.
from rotational speeds, auto ranging. RPM. Auto ranging. 60 to 50000 RPM. Auto-ranging.
DISPLAY : 5 digit bright LED display
DISPLAY : 5 digit bright LED display DISPLAY : 5 digit bright LED display RANGE : 60 to 50000 RPM auto ranging
RANGE : 60 to 50000 RPM auto ranging RANGE : 60 to 100000 RPM auto ranging RESOLUTION: 0.1 RPM for 60 to 1000 RPM
RESOLUTION: 0.1 RPM from 60 to 1000 RPM RESOLUTION: 0.1 RPM for 60 to 1000 RPM and 1 RPM from 1000 to 50000 RPM.
and 1 RPM from 1000 to 50000 RPM. 6 to 5000 and 1 RPM from 1000 to 100000 RPM. SAMPLING RATE : 1 Sec
MPM (meters per minute) for surface speed with Measuring rang is from 4 inches to 12 inches. ACCURACY : 0.05% 1 digit
resolution of 0.1 RPM. SAMPLING RATE : 1 Sec POWER REQUIREMENT: 230 10% volts AC,
SAMPLING RATE : 1 Sec ACCURACY : 0.05% 1 digit 50Hz, 4VA.
ACCURACY : 0.05% 1 digit POWER REQUIREMENT: Battery operation SIZE & WEIGHT (Approx): 48 mm (H) x 96 mm
POWER REQUIREMENT: Battery operation with with 4 pencil cells AA, R6 of 1.5 volts. Auto (W) x 120 mm (D), 500gms.
4 pencil cells AA, R6 of 1.5 volts. Auto power off power off facility provided to help conserve cell STANDARD ACCESSORIES : Sensor &
facility provided to help conserve cell life. life. instruction manual
SIZE & WEIGHT (Approx): 40mm (H) x75 (W) x SIZE & WEIGHT (Approx): 40mm (H) x75 (W) x
200 mm (L), 330gms. 200 mm (L), 280gms. SENSORS
STANDARD ACCESSORIES : Instruction manual, STANDARD ACCESSORIES : Photo reflective
conical type male rubber tip (2), hollowed funnel tape of 1000mm x 12mm, instruction manual Proximity Sensor for 81N PM
type female contact tip and disc type peripheral and padded plastic carrying case PNP type inductive proximity sensor of 70 mm
rubber wheel for surface speed measurements length and 18 mm diameter with lock nut. The
and padded plastic carrying case. sensor should be mounted with front plane at a
distance of 3 to 5 mm from a M.S. bolt, teeth,
pulsor disc or wheel (which is concentrically
mounted on the rotating shaft of rotor or drive)
rotating shaft.

Digital Tachogenerator for TM801


Digital Tacho generator / Encoder 60ppr type
sensors. The sensor should be directly coupled
to the rotar whose RPM is to be measured. The
digital pulses generated are LS-TTL compatible
& proportional to the speed.

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

-9-
LUX METER ANEMOMETER SOUND LEVEL METER
(LIGHT INTENSITY METER) (AIR VELOCITY) (NOISE LEVEL METER)
(LUX / FC)

ACCESS Lx101 ACCESS AM4201A ACCESS SL 4010

200000
LUX

ACCESS Lx101 Digital Lux meter is a precise ACCESS AM4201A measures air velocity. Digital ACCESS SL4010 The sound level meter is useful to
instrument for environmental test, used for Anemometer is a wing type device for wind, airflow and measure the ambient sound level around factories,
measuring the luminance of different locations gas direction / speed measuring. Useful for whether, workshops, schools, residential, offices, road, audio etc.
RANGE, RESOLUTION AND ACCURACY ventilation systems, centralized air conditioning and It also can be useful for noise analysis in engineering,
various other industries, laboratories & colleges. product quality control, health treatment etc.
Range (Lux) Res. Accuracy FEATURES: FEATURES:
200 0.1 Data hold function, with back light for easy reading, low Automatic shifting, A & C weighting, high speed (FAST) /
+ 3% + 10 digit
2000 1 (< 10000 Lux) battery indication, over range indication. low speed (SLOW) response rate, MAX lock.
+ 4% + 10 digit AIR VELOCITY RANGE AND ACCURACY : RANGE, RESOLUTION AND ACCURACY :
20000 (Reading x 10) 10 0.40 to 30.00 meters /second with accuracy of +/- 2% 30 dB to 130 dB in 6 ranges of 30 to 80 dB, 40 to 90 dB, 50
(> 10000 Lux)
200000 (Read x 100) 100 1.4 to 108.0 km/hr with accuracy of 2% to 100 dB, 60 to 110 dB, 70 to 120 dB, & 80 130 dB.
PARAMETER : LUX / FC (Selectable) 2 to 98.5 ft/sec with accuracy of 2% Resolution: 0.1dB, Accuracy: + 2%, Sampling rate:2 /sec.
RANGE : Auto / Manual (Selectable) 0.8 to 58.0 knots with accuracy of 2% FREQUENCY RANGE : 30Hz ~ 8KHz
DISPLAY : 3 digit LCD with annunciations DATA HOLD FACILITY : Data hold facility is provided to DIGITAL DISPLAY : 4 digit LCD Display of 12 mm height,
FACILITIES : Data hold, Max. Min, Range, store the desired value on display. ANALOG BAR DISPLAY: Each analog bar represents 1
Mode, REC. (for Data Acquisition) DISPLAY : 3 digit, 1999 count LCD display of 20 mm dB, sampling rate is 20 times/sec.
SENSOR : Separately attached light sensor to height. Back light and measurement units are provided. OPERATING TEMPERATURE: 0 to 40OC
take measurement at an optimum position POWER REQUIREMENTS : 9 volts battery. OPERATING HUMIDITY: 10-80 % RH
POWER : 1.5V x 2 (AAA) Batteries SIZE & WEIGHT (approx) : 185 mm (L) x 74 mm (W) x POWER REQUIREMENT: 1.5 V batteries 4 no.
SIZE & WEIGHT (approx) : 130 mm (L) x 55 33 mm (H), 360gms SIZE & WEIGHT (approx) : 193 mm (L) x 60 mm (W) x 29
mm (W) x 30 mm (H), 180 gms STANDARDS ACCESSORIES: 9volt battery, mm (H), 230 gms
STANDARD ACCESSORIES : Battery, Instruction manual and carrying cover. STANDARD ACCESSORIES: Battery, Instruction
Instruction manual & Carrying case manual and carrying cover

DIGITAL FLUX METER MOISTURE METER TEMPERATURE CUM


(WOOD) HUMIDITY METER
ACCESS FM01 ACCESS MM07 (HYGRO-THERMOMETER-CLOCK)
ACCESS TH

Low cost, Access FM01 Digital Flux Meter is a ACCESS MM07 Moisture meter is useful to measure ACCOESS TH measures real time, min, max values of
versatile Instrument for testing Magnetic Flux. the containing water of wood, bamboo, cotton, tobacco room temperature (C / F) and humidity. Date & Clock
It can be used in Teaching Institutes as well as etc. Sharp pins are provided on the top (with safety displays time in hours and minutes in 12 / 24 hour format.
for Industrial purposes. cover) which are to be inserted in to the object for hourly & everyday alarm function. Foldaway stand for
RANGE : 0.1-10.0 KiloGauss finding the water content convenient viewing angle & Wall mounting key hole
PROBE : Attached measurement probe with FEATURES: Data hold, back light & power button. % & TEMPERATURE :10C to +50C (+14F to +122F)
cover. Low battery symbol HUMIDITY : 20% to 99% RH
OPERATING TEMPERATURE : 10OC-60OC DISPLAY: Digital, large size LCD TIME : 12 / 24 hour format, AM / PM, alarm display for
POWER REQUIREMENT: 220V.-240V, 50Hz TEST RANGE: 5% to 40% RESOLUTION: 1% hourly / every day alarm.
Single Phase AC mains ACCURACY: +1% DISPLAY : Backlit large LCD
SIZE & WEIGHT (approx) : 230 mm (L) x 180 POWER REQUIREMENT: 9V battery POWER REQUIREMENT : 1.5 volts, AAA cell.
mm (W) x 105 mm (H), 1.5 Kg SIZE & WEIGHT (approx) : 150 mm (L) x 67 mm (W) x SIZE & WEIGHT (approx) : 105mm(L) x 98 mm(W) x
STANDARD ACCESSORIES : Manual 32 mm (H), 150 gms (approx) 21mm (H).105gms
STANDARD ACCESSORIES: Battery, Instruction STANDARD ACCESSORIES : 1.5 volts cell and
sheet and carrying cover instruction manual.

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 10 -
SOLDERING & DESOLDERING SOLUTIONS
SOLDERING STATION DESOLDERING GUN SOLDERING & DESOLDERING
(Digital Desoldering Station) STATION
ACCESS 936 ACCESS-915 ACCESS 917

ACCESS 936 Soldering Station is ESD Safe, with The Desoldering Gun (Digital Desoldering Station) is ACCESS 917 Soldering & Desoldering Station is a
insulated transformer for low 24V soldering iron a microprocessor based, LCD, High performance microprocessor based, dual LCD, high performance,
and electronic temperature control lead free desoldering tool for 1 or 2 sided PCB (PTH). multi-function station for production and rework.
TEMPERATURE RANGE : 200C ~ 480C.
Specication De-soldering Gun Specication Soldering Iron De-soldering Gun
POWER CONSUMPTION : Station: 24V/60W,
Iron: 24V/50W. Voltage/Power 24V AC/80Watt Voltage/Power 24V AC/ 60Watt 24V AC/80Watt
CONTROL SYSTEM : Electroic. Temperature 180OC to 480OC Temperature 60OC to 480OC 160OC to 480OC
POWER REQUIREMENT: 220 V AC Mains, 50 Hz Heater PTC Ceramic Heater PTC Ceramic PTC Ceramic
SIZE & WEIGHT (approx) :125mm(W) x 150mm(D) Display Backlit LCD Display Backlit LCD Backlit LCD
x 90 mm (H), 1.5 Kg. Vac. Pressure 600mm Hg Vac. Pressure 600mm Hg
STANDARD ACCESSORIES: Nozzles ( 2nos)
POWER REQUIREMENT: 220 V AC Mains, 50 Hz POWER REQUIREMENT: 220 V AC Mains, 50 Hz
SIZE & WEIGHT (approx): 240mm(L) x 130mm(W) SIZE & WEIGHT (approx): 235mm(L) x 225mm(W)
x 170 mm(H), 2.6 Kg. Approx x 170 mm(H), 3.7 Kg. Approx

SMD REWORK STATION SMOKE SOLDER POT


- SMD SOL & DESOL STATION ABSORBER ACCESS SP50
ACCESS 850A ACCESS SA07

ACCESS 850A SMD Rework Station is ESD SAFE, ACCESS SA07 Smoke Absorber, is very useful for ACCESS SP50 Solder Pot is useful for lead free
suitable for QFP & SOP I.C.s. removing noxious fumes quickly, safely & efficiently. solder, easy & fast tinning of cables, wires & coils &
TEMPERATURE RANGE :100 C ~ 420 C It has a high performance fan & an activated carbon also for soldering of through hole components.
AIR FLOW : 24 L / Minute (max.) filter designed to absorb flux & lead fumes.
CONTROLS : Power On / Off, Air flow & Heater The angle is adjustable & complete unit is easy to POWER CONSUMPTION : 150 W
POWER CONSUMPTION : 270 W move / place. Low noise & long life of the service fan TEMPERATURE RANGE : 200C ~ 480C
POWER REQUIREMENT: 220 V AC Mains, 50 Hz is an advantage. The filter is replaceable. POT DIAMETER & CAPACITY: 50mm ;500gms
SIZE & WEIGHT(approx): 270mm(D) x 185mm(W) x FILTTER : Activate carbon filter (replaceable) MELTING TIME: 8 Min
175 mm(H), 4 Kg. POWER CONSUMPTION : 25 W MATERIAL: Stainless steel
3
STANDARD ACCESSORIES: Nozzles ( 2nos) ABSORPTION CAPACITY : 1m / minute (max) CONTROLS : Power On / Off & heater
CONTROLS : Power On / Off POWER REQUIREMENT: 220V AC Mains, 50 Hz
POWER REQUIREMENT: 220V AC Mains, 50 Hz SIZE & WEIGHT: 155 mm (D) x 95 mm (W)
SIZE & WEIGHT (approx): 135 mm (D) x 220 mm (W) x 60 mm (H), 600 gms (approx)
x 275 mm (H), 1.5Kg

MAGNIFIER MAGNIFIER WITH LIGHT


(WITH LIGHT & STAND) (HAND HELD)
ACCESS ML07 ACCESS ML03
ACCESS ML07 Magnifier with light is a desktop folding arm type model, ACCESS ML03 is a compact hand
useful to view and check micro / mini components, densely fitted PCBs or held magnifier for Engineers, Artist,
at any place requiring magnification / lighting Scientists, Photographers,
LENS : Magnifying lens (X3 : X5), Lens can be tilted & rotated as required Industries & for all.
LENS DIAMETER : 90mm LENS : Magnifying glass (90mm)
LIGHT : Bright stable & reliable light. LIGHT: Inbuilt with On / Off button
STAND : Adjustable POWER REQUIREMENT: 3V DC
CONTROLS : Power On / Off (2 X 1.5V AA Cell)
POWER REQUIREMENT: 220V AC Mains, 50 Hz SIZE & WEIGHT (approx): 195 mm
SIZE & WEIGHT (approx): 220 mm (L) x 105 mm (W) x 320 mm (H) (L) x 95 mm (W) x 30 mm (H)
(adjustable), 1Kg (adjustable), 150 gms

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 11 -
DIGITAL INSULATION DIGITAL EARTH RESISTANCE THERMOMETER
TESTER (Megger) TESTER WITH KIT (Non Contact Type With Laser Beam)
ACCESS DITM 910 ACCESS 900 ACCESS 8811A

With ter
e
Multim

Digital Insulation Tester more popular as megger also Digital Earth Resistance Tester is with more complete ACCESS 8811A is a non contact type thermometer,
has an inbuilt Multimeter. Button operated function & has ease of operation. It can test earth with laser pointer. The IR reflected beam measures
DISPLAY : 3 3/4 Digit (3999) large backlit LCD resistance of various earth systems including power the temperature. It is useful in process, safety / fire
MEASUREMENT VOLTAGE : 250V / 500V / 1000V systems, electric equipment, lightning conductors as inspections, printing, dryer, plastic molding, asphalt,
INSULATION RESISTANCE : 0.25MW ~ 40GW well as resistance value of low resistance conductor food preparation, marine, education sector etc
ACCURACY : 400kW ~ 200MW 3%5 ; and also perform AC voltage test FUNCTION : Real time, max, min in C / F, Auto off.
200M ~ 4GW 5% 5 ; 4G-40GW 10% 5 DISPLAY : 3 1/2 Digit large backlit LCD RANGE , RESOLUTION & ACCURACY :
SHORT CIRCUIT CURRENT : 1.5mA or more EARTH RESISTANCE : 0-20 W 2 % 0.1 W Range : -50 to +580C / -58 to +1022F ; Res: 0.1C / F
MEASUREMENT TIME : 1 / 2 /10 Minutes 0-200 W 2 % 3 digit Accuracy : 100C + 2% / 100C +2C (depends
MULTIMETER 0-2000 W 2 % 3 digit on emissivity of object under test
ACV : 4/40/400V0.8%5,700V1%5 dgt EARTH VOLTAGE : 0-200V 1% 4 digit DISTANCE FACTOR ("D:S" Distance to spot ratio): 16:1
DCV : 400m/4/40/4000.5%5dgt, RESPONSE TIME : 5 Sec appx. (Earth Resistance) As the distance from thermometer to the object
1000V0.8%5dgt 2 Sec appx. (Earth Voltage) increases spot size of measuring area becomes
DCA : 40 mA/400mA0.8% 5dgt OVERLOAD PROTECTION : 200V (for 10 sec.) larger. It is named as "D:S". Here the efficient testing
ACA : 40 mA/400mA1%5dgt POWER REQUIREMENT :1.5 x 6 AA type batteries distance is 16 times as the diameter of the target
RESISTANCE :400/4k/40k/400kW 0.8% 5dgt ; SIZE & WEIGHT (approx) : 218 mm (L) x 122 mm object. The target must be larger that the spot size.
(W) x 75 mm (H). 900 grams. Smaller the target, closer measuring distance.
4MW 1% 3dgt ; 40MW 3%3 dgt
STANDARD ACCESSORIES : batteries, instruction DISPLAY : Large backlit LCD, -, C, F, low bat & laser
CAPACITOR : 40n/400n/4u/40uF 3% 5dgt
manual, testing leads and Bars kit with bag icon, data recall, hold, Hi/Lo temp. alarm,
FREQUENCY : 40/400/4k/40k/400k/4MHz0.5% 3
min/max/avg, diff., emissivity display.
AUDIO : Buzzer for Continuity / Diode Test
POWER REQUIREMENTS : 9 volts battery
POWER REQUIREMENTS : 1.5 x 6 AA type batteries
SIZE & WEIGHT(approx) : 120 mm (L) x 47 mm (W)
SIZE & WEIGHT (approx) : 156 mm (L) x 64 mm
x 175 mm (H). 250 grams
(W) x 170 mm (H). 650 grams
STANDARD ACCESSORIES : 9V battery, instruction
STANDARD ACCESSORIES : batteries, instruction
manual and carrying cover
manual, testing leads and carrying cover.

INSULATION TESTER (Megger) EARTH RESISTANCE METER DIGITAL IC TESTER


PICO 500V/100MEG PICO 0-100 Ohms
ACCESS DIT24
PICO 1000V/200MEG Earth resistance kit

Insulation Testers are rugged, hand crank type, Earth Resistance Meter is a rugged, hand crank ACCESS DIT 24 is a hand held tester, designed to
direct reading analog testers for measuring insulation type, direct reading analog meter for measuring earth test over 300+ Digital Logic IC's commonly used in
resistance of various electrical rotating machines, electrode resistance, soil resistance, earth continuity, industry. It is ideal for incoming inspection at
power distributions line, communication cables, neutral & earth loop resistance, etc. The inbuilt hand manufacturer's end, troubleshooting at maintenance
insulators, control & switching instrument etc. The driven generator & solid state circuit provides direct depots, repair shops or in field service and education
inbuilt hand driven generator & solid state circuit gives reading of resistance. Used by Industries, railways, in ITI's, Polytechnics & Engineering colleges
a stabilized HV DC output. Used by Industries, defence, utilities, power plants, geological surveys, l Tests TTL family of ICs 74xx (commercial grade) &
railways, defence, utilities, power plants, geological institutes, ITIs, polytechnics, Engineering colleges 54xx (military graed) (LS/HC/ HCT/ ALS/ S / AS / F /.. )
surveys, educational institutes, ITIs, polytechnics, etc. Meets the requirements as per IS 9223-89 l Tests CMOS family of ICs - 40xx, 41xx, 45xx
Engineering colleges etc. They meet the RANGE: 100 Ohms AUTO FIND DEVICE - Conducts exhaustive
requirements as per IS 2992-87 ROTATIONAL SPEED: 160rpm (min) with handle functional tests & finds out of the number of an
RANGE: 500V / 100MEG or 1000V / 200MEG. RESPONSE TIME: 3 Sec. approx unknown device ( TTL & CMOS)
ROTATIONAL SPEED: 160rpm (min) with handle ACCURACY: +5% of FSD as per IS stipulations l Alphanumeric LCD display shows IC number, Test
RESPONSE TIME: 3 Sec. approx STANDARD ACCESSORIES : Instruction sheet & Passed / Test Failed and other status messages
ACCURACY: +5% of FSD as per IS stipulations. carrying case l 24Pin Universal ZIF socket accommodates
STANDARD ACCESSORIES : Instruction sheet, test SIZE & WEIGHT(approx) : 150 mm (L) x 115 mm (W) both 0.3'' and 0.6'' DIP ICs & audible alarm
leads & carrying case x 70 mm (H). 750 grams STANDARD ACCESSORIES : Instruction manual,
SIZE & WEIGHT(approx) : 150 mm (L) x 115 mm OPTIONAL ACCESSORIES : Earth Resistance Kit 9V PP3 Battery & 9V DC Adapter
(W) x 70 mm (H). 750 grams It consist of hammer, screw driver, 4 M.S. spikes, 4 SIZE & WEIGHT(approx) : 240 mm (L) x 130 mm (W)
spools of wire, carrying bag x 50 mm (H). 450 grams

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 12 -
TEMPERATURE CALIBRATORS & SIMULATORS

SE4024 SE406 SE407 SE408

DIGITAL CALIBRATOR DIGITAL CALIBRATOR T/C / RTD CALIBRATOR DIGITAL CALIBRATOR


Model SE4024 SE406 SE407 SE408
Type Table Top / Mains Operated Portable / Battery Operated

Display 4 Digit, 0.4"ht LED 4 Digit, 0.5"ht LCD

Ranges 0-200mV / 0-2V / 0-20V DC 0 to 199.99mV DC 0 to 600OC for Fe/Con T/C (J type) 0 to 199.99mV DC
0-200A / 0-2 mA / 0-20 mA DC 0 to 19.999 mA DC 0 to 1200OC for Cr/Al T/C (K type) 0 to 10.000V DC
-100.0OC to +400.0OC (RTD) - 100.0OC to +400.0OC for PT100 RTD 0 to 19.999 mA DC

Accuracy 0.05% 2 digit for 200mV 0.05% 2 digit for mV / mA 0.25% 2 dgt - Fe/Con T/C / PT100 RTD 0.05% 2 digit for mV
0.1% 2 digit for 2V & 20V 0.25% 2 digit for PT100 RTD 0.25% 2 digit - Cr/Al T/C upto 1000OC 0.1% 2 digit for V
0.25% 2 digits for current 1% 2 digit above 1000OC for Cr/Al/ T/C 0.25% 2 digit for mA
Selection Measure / Source Measure / Source Measure OC / Source OC T/C / PT100 RTD Measure / Source
(Selection by push mV / mA / PT100 RTD PT100 RTD / T/C
button) Voltage / Current mV / mA Fe/Con T/C / Cr/Al T/C mV / V / mA
EXT PT100 RTD / PT100 RTD EXT PT100 RTD / PT100 RTD Source
source
Measure Voltage: mV / Volts mV / mA External Fe/Con T/C, Cr/Al T/C, PT100 mV / V / mA
Current: mA / mA External PT100 RTD in OC RTD in OC

Source Voltage: mV / Volts A) mV / mA output adjustment by A) Fe/Con T/C / Cr/Al T/C output mV / V / mA output
Current: mA / mA 'Coarse' & 'Fine' potentiometers adjustment by 'Coarse' & 'Fine' adjustment by 'Coarse' &
mA load 500W potentiometers 'Fine' potentiometers
Output adjustment by 'Coarse' & mA load 500W
B) For PT100 B) PT100 RTD output is adjustable by
'Fine' Potentiometer means of 'Fine' Potentiometer
I) In PT100 RTD / Measure mode
desired temperature in OC is
adjustable by means of 'Fine'
(PT100) potentiometer

ii) In PT100 RTD / Source mode,


resistance value corresponding
to set temperature is available at
output terminals
Indications Decimal Point, Over-range & -ve polarity

Power 230 10% VAC,50Hz 9V DC Battery (2 cells)

Size & Weight 90 mm(H)x190 mm (W) x190 180 mm(H) x 100 mm (W) x 40 mm(D), 800 gms (approx)
(approx) mm(D), 1.8 Kg

Standard Test leads, Instruction Manual Test leads, Battery, Instruction Manual & Box
Accessories

SMPS MODULES & SUPPLIES


ACCESS
ACCESS ACCESS SMPS VARIABLE
SMPS MODULES SMPS ADAPTOR CV/CC POWER SUPPLY
(With 2 Digital Meters)

5V / 1A 5V / 1A 0-30V / 5A
5V / 5A 12V / 1A 0-30V / 10A
12V / 5A 24V / 1A
24V / 5A
Note: Other models / ranges available
Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 13 -
TEMPERATURE INDICATORS (THERMOMETERS) / CONTROLLER
(Contact type, 3.5 Digit)

250OC 750OC
Temperature Controller
cum Indicator
Digital Thermometer Digital Thermometer Temperature Indicator (1 potentiometric set point)
Model ACCESS 902C 250 SE 221PK SE221K SE220K
Thermometer with wire type Cr/Al T/C 0 to +1200OC, Cr/Al T/C type 0 to +1200OC, Thermocouple type 0 to +1200OC,Thermocouple type
(-50 to +250OC) SE 221PRTD200 SE221RTD200 SE200RTD200
-100 to +200OC, RTD type -100 to +200OC, RTD type 0 to +200OC, RTD type
ACCESS 902C 750
Thermometer with probe type Cr/Al T/C SE 221PRTD400 SE221RTD400 SE200RTD400
(-50 to +750OC) -100 to +400OC, RTD type -100 to +400OC, RTD type 0 to +400OC, RTD type

Type Digital Thermometer Temperature Indicator Temperature Controller cum


Portable / Battery Operated DIN / Mains operated Indicator 1DIN/Mains operated

Display 3.5 Digit, 7 Seg. LCD, with Decimal point, over-range & negative polarity 3.5 Digit, 7 Seg. LED (Dec. point, over-range & negative polarity)

Range / O
-50 to +750 C / 1 CO O
221PK 0 to +1200 C/1 C O
221K 0 to+1200OC/1OC 220K 0 to+1200OC/1OC
O O O O
Resolution 221PRTD200 -100 to+200OC/0.1OC 221RTD200 -100 to+200 C/0.1 C 220RTD200 0 to+200 C/0.1 C
221PRTD400 -100 to+400OC/1OC 221RTD400 -100 to+400OC/1OC 220RTD400 0 to+400OC/1OC
Accuracy 0.75% 1OC from 0 to 500 OC 0.5% 1OC upto 1000OC. 0.5% 1OC upto 1000OC & 1.0% 2OC above 1000OC.
1% 1OC from 500 to 750 OC 1.0% 2OC above 1000OC. 1% 1OC for On / Off control action & 1 NC relay contact in 220

Sensor Cr/Al thermocouple (K type) Not provided (Available at extra cost)


Power 9V Battery 230V 10% AC, 50Hz
Requirement
Size & Weight 20 mm(H) x 70 mm(W) x 105 mm(D) 30mm(H)x80mm(W)x165mm(D), 48mm(H) x 96mm(W) x 110mm(D) 96mm(H) x 96mm(W) x
120 gms (approx) 200gms (approx) with panel cutout of 46mm (H) x 110mm(D) with panel cutout
92mm (W), 400gms (approx) of 92mm (H) x 92mm (W),
600gms (approx)
Standard Instruction Sheet, T/C Sensor, Instruction Sheet, Battery, Carrying Instruction Sheet, Panel mounting brackets
Accessories Battery, Carrying case case

TEMPERATURE TEMPERATURE SENSORS


TRANSMITTERS K(Cr/Al) T/C sensors for SE221PK
RTD(PT100) for SE221PRTD200/400
K(Cr/Al) T/C sensors for SE220 & 221K
RTD(PT100) for SE220 & 221RTD200/400
(Two Wire Head Mount Simplex Temp Tx) Immersion Probe Type:TC22K1 Straight Probe Type:TCSK2
K (Cr/Al) T/C sensor K (Cr/Al) T/C sensor
TCHTx400 with handle, 12"long 6"long SS sheath,
(T/C head type transmitter) Inconnel SS sheath, Dia:6mm & 1 mtr Dia:6mm & 2 mtr fibre SS braded cable
PVC compensating cable (0 to 1200 C). (0 to 600 C).
RTDHTx400 Needle Probe Type:TC24K Immersion Probe Type:TC23K1
K (Cr/Al) T/C sensor K (Cr/Al) T/C sensor
(RTD head type transmitter)
with handle, 5" long with Al head, 12" long
SS sheath, Dia:3mm & 1 mtr PVC Inconnel sheath, Dia:6mm & 1 mtr PVC
compensating cable (0 to 600 C). compensating cable (0 to 1200 C).
Model TCHTx400 RTDHTx400
Leaf (Surface) Probe Type:TC25K Immersion Probe Type:TC21K1
Cr/Al (K) T/C 2 or 3 wire K (Cr/Al) T/C sensor K (Cr/Al) T/C sensor
Input
(ungrounded) PT100 RTD with handle, 6" long with Al head, 12" long
Output 4 to 20mA DC linearized (2 Wire) SS sheath, Dia:6mm & 1 mtr long PVC SS sheath, Dia:6mm & 1 mtr long PVC
compensating cable (0 to 600 C). compensating cable (0 to 600 C).
Range 0 to 400OC (32 to 752OF)
Prick Probe Type:TC28K Immersion Probe Type:RTD54
Accuracy 1% of the range K (Cr/Al) T/C sensor RTD (PT100) sensor
Loop 600 Ohms at 24V DC (supply dependent) with handle, 4" long with Al head, 12" long
SS sheath, Dia:3mm & 1 mtr long PVC SS sheath, Dia:6mm & 1 mtr long cable
Adjust Zero & Span adjust (-100 to +400 C).
compensating cable (0 to 400 C).
Supply 24V DC nominal (12 to 36 V DC)
Needle Probe Type:RTD51 Straight Probe Type:RTD53
Size & RTD (PT100) sensor RTD (PT100) sensor
44mm(Dia) x 26mm(H), 70gms (approx)
weight with handle, 5" long 6" long SS sheath,
Other types / range Tx models available on request SS sheath, Dia:4mm & 1 mtr long teflon Dia:6mm & 2 mtr long cable
cable (-100 to 400 C). (-100 to +400 C).

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 14 -
ANALOG METERS
ANALOG METERS OHM METERS ANALOG MULTIMETER
(Analog Portable Desk Stand Meters) (Analog Desk Stand Series (0-2000MW / 1000V)
ACCESS EDM80 & Shunt Type) ACCESS 999

ACCESS EDM80 Series of Analog Portable Desk Stand meters ACCESS 999 Analog Multimeter measures AC &
are very popular and useful in Science Colleges, ITIs, ACCESS AMO-200 DC voltages, AC & DC Current, Resistance,
Polytechnics, Engineering Colleges, PG, NIC, IITs, R&D / Training (Ohm meter Series type) Frequency in various high ranges, usually not
Centers and Industries found in normal analog multimeters. High input
DISPLAY: Large Square meter with Anti Parallax Scale for better ACCESS AMO-201 inpedance Works on 1.5V X 2 & 9V X 1 batteries.
viewing (Ohm meter Shunt type) Parameter Range Accuracy
PACKING: Individual Thermocol Box
OHM Meter Series Type Shunt Type DC Voltage 0.1/0.5/2.5/10 3%fs
Analog Portable Desk Stand Meters MC-Moving Coil Model AMO-200 AMO-201 /50/250/1000V
Access Model: EDM-80 Range 0 to 2000W 0 to 100W AC Voltage 0.1/0.5/2.5/10
4%fs
Parameter Ranges (any one range) Type MR100 (True RMS) /50/250/1000V
Moving Coil Type DC Analog Portable Desk Stand DC Current 0.05/0.25/2.5/ 3%fs
Galvanometer DC 30-0-30 division (20mA/Div) Supply 1.5V AAA Battery 25/250mA
Galvanometer DC 30-0-30 division (1mA/Div) Packing Individual Thermocol Box 10A 4%fs
mAmmeter DC 0-50/100/200/300 AC Current 0.05/0.25/2.5/25 4%fs
SIZE & WEIGHT (approx): 140 mm (D) x (True RMS) 250mA/10A 5%fs
mAmmeter DC 0-500/600/1000 100 mm (W) x 100mm (H), 300gms
Milliammeter DC 0-1/2/5/10/25/50/100/250/500/1000 Resistance 2K/20K/200K/2M/
3%fs
Ammeter DC 0-1/2/5/10 20M/2000MW
Ammeter DC 0-15/20/25/30 CELL TESTER Frequency 0.25/2.5K/25K Hz
(3-0-3 Volts) 3%fs
Millivoltmeter DC 0-50/100/150/200/250/500/1000
ACCESS CT242 Other Diode, Transistor,
Voltmeter DC 0-1/2/5/10/25/50/100/250/500/600 NA
checks Continuity <200W
Moving Coil Rectifier Type AC
mAmmeter AC 0-50/100/200/250/500/1000 Protection Internal fuses,
Milliammeter AC 0-1/2/5/10/25/50/100/250/500/1000 Varactor & Diodes
Ammeter AC 0-1.5/2/2.5/5 OTHER FEATURES : Robust protective side
Voltmeter AC 0-2/5/10/25/50/100/250/500/600 holsters with Tilt Stand. Power ON LED & Auto
Moving Coil Rectifier Type AC - DC power OFF
mAmmeter AC-DC 0-50/100/200/250/500/1000 SUPPLY : 1.5V X 2 & 9V X 1 batteries
Milliammeter AC-DC 0-1/2/5/10/25/50/100/250/500/1000 DISPLAY : Large Analog Meter with Anti-parallex
scale
Ammeter AC-DC 0-1/2/2.5/5
SIZE AND WEIGHT: 160mm(L) X 130mm
Voltmeter AC-DC 0-3/5/10/25/50/100/250/500 (W) X 42mm(H) 340gms (approx)
SIZE & WEIGHT (approx): 125 mm (D) x 80 mm (W) x 85mm SIZE & WEIGHT (approx): 205 mm (L) x STANDARD ACCESSORIES: Inbuilt Test
(H), 200gms 65 mm (W) x 40mm (H), 200gms Leads, User Manual & Battery

AC / DC POWER SUPPLIES & BATTERY ELIMINATORS


ACCESS BE11 ACCESS BE31

BATTERY ELIMINATOR STEP DOWN TRANSFORMER HV DC Power Supply


(2-12V DC / 1A in steps of 2V) (2-12V AC / 1A in steps of 2V) (Unregulated Variable with
2 Analog meters)
ACCESS BE21 ACCESS BE41 ACCESS1005
(0-100V DC / 5A)
ACCESS3005
(0-300V DC / 5A)
IC REG. BATTERY ELIMINATOR AC/DC Power Supply
(2-12V DC / 1A in steps of 2V) (2-12V AC/DC / 1A in steps of 2V)
Note: Other models / ranges available
Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 15 -
DIGITAL METERS
DIGITAL PANEL METERS DIGITAL DESK STAND METER
(V, A and Line frequency) (Portable 3.5 digit LED / LCD DPM)
3.5 Digit 7 segment LED DPM
ACCESS 34A DC ACCESS 34P
(3.5 Digit LED mains operated)
ACCESS 34A AC
(For special ranges / CT / Shunt based
DPM ` 100/- extra, CT / Shunt cost extra.) ACCESS 36P
(3.5 Digit LCD battery operated)
4 Digit LED line frequency meter
ACCESS 34A81 34P LED 36P LCD
MEASUREMENTS : Meters for measurement of different parameters such as, 34P & 36P portable type digital desk stand meters are available for DC/AC voltage
DC mV / V / kV / mA / mA / A / kA AC mV / V / kV / mA / mA / A / kA DC/AC current measurements. Longer life due to no moving / fragile parts. Housed
Special process parameters using transducers of 0 to10V / 4 to 20mA DC outputs. in rugged plastic cabinet with convenient viewing angle. Useful for colleges, R&D
SIZE & WEIGHT (approx): Panel cutout 46 mm (H) x 92 mm(W) with cabinet size organizations, laboratories, industries, railways, defense establishments etc.
of 48 mm (H) x96mm (W) x 75mm(D). Panel mtg hardware is provided. (Wt:0.4kg) DISPLAY: 34P - 3.5 dgt, LED & 36P - 3.5 dgt LCD
DISPLAY: 3.5 digit in model 34A, except 4 digit in 34A81. 7 seg, LED of 13 mm (H) with decimal point, negative polarity and over-range indications.
with decimal point, negative polarity and over-range indications. RESOLUTION: 1 in 1999
RESOLUTION: 1 in 1999 except, 1 in 9999 in 34A81. POWER REQUIREMENTS: 34P - 23010% V AC, 50Hz 36P - 9V Battery
AUX SUPPLY: 230 10% volts AC, 50Hz, 1 Phase AC Mains SIZE & WEIGHT (approx): 105mm (H) x 100mm (W) x 140mm (D). 200 gms
Note: 34P & 36P are available in various ranges as per chart
DC mV /DC V MEASUREMENTS
3.5 Digit Panel / Portable Meters
Range Model Resolution Accuracy Input 4.5 DIGIT DIGITAL PANEL METERS
Impedance
Panel Portable (V, A and Line frequency)
0 to 200mV DC 34A4 34P4 / 36P4 0.1mV 0.1% 2
0 to 2V DC 34A5 34P5 / 36P5 0.001V counts 1000MW
4.5 Digit 7 segment LED DPM
0 to 20V DC 34A6 34P6 / 36P6 0.01V
0 to 200V DC 34A7 34P7 / 36P7 0.1V 0.2% 2 ACCESS 45A DC
counts 10MW ACCESS 45A AC
0 to 1000V DC 34A8 34P8 / --- 1V
(For special ranges / CT / Shunt based
AC mV /AC V MEASUREMENTS DPM ` 200/- extra, CT / Shunt cost extra.)
3.5 Digit Panel / Portable Meters MEASUREMENTS : Meters for measurement of different parameters such as,
Range Input
Panel Portable Resolution Accuracy Impedance DC mV / V / kV / mA / mA / A / kA AC mV / V / kV / mA / mA / A / kA
Special process parameters using transducers of 0 to10V / 4 to 20mA DC outputs.
0 to 200mV AC 34A14 34P14 / 0.1mV 10KW RANGES : DC or AC V : 199.99mV / 1.9999 V / 19.999 V / 199.99 V / 1000.0 V.
0 to 2V AC 34A15 34P15 / 0.001V 100KW DC or AC A: 199.99m A / 1.9999 mA / 19.999mA / 199.99 mA / 1.9999 A / 10.000 A.
0.5% 2
0 to 20V AC 34A16 34P16 / 0.01V 1MW DISPLAY: 4.5 digit, 7 seg, LED of 13 mm (H) with decimal point, negative polarity
counts
0 to 200V AC 34A17 34P17 / 36P17 0.1V 10MW and over-range indications.
0 to 1000V AC 34A18 34P18 / 1V 100MW ACCURACY: 0.025 % 2 Dgt RESOLUTION: 1 in 19999.
AUX SUPPLY: 230 10% volts AC, 50Hz, 1 Phase AC Mains
DC MICRO-AMP / MILLI-AMP/AMP/KILO-AMP MEASUREMENTS SIZE & WEIGHT (approx): Panel cutout 46 mm (H) x 92 mm(W) with cabinet
size of 48 mm (H) x96mm (W) x 75mm(D),0.4kg. Panel mtg hardware provided.
3.5 Digit Panel / Portable Meters
Range Model Input
Resolution Accuracy Impedance
Panel Portable DIGITAL SIGNAL FREQUENCY METERS
0 to 200 mA DC 34A34 34P34 / 36P34 0.1 mA 1KW
0 to 2mA DC 34A35 34P35 / 36P35 0.001 mA 100W
(4 Digit 7 segment LED)
0 to 20mA DC 34A36 34P36 / 36P36 0.01 mA 10W
0 to 200mA DC 34A37 34P37 / 36P37 0.1 mA
0.5% 2
1W
34A91 (10.00 to 99.99 Hz)
counts 34A92 (10.0 to 999.9 Hz)
0 to 2A DC 34A38 34P38 / 36P38 0.001 A 0.1W
0 to 10A DC 34A39 34P39 / 36P39 0.01 A 0.01W 34A93 (10 to 9999 Hz)
Higher currents 34A42 --- / --- Ext. Shunt Shunt Res. 34A94 (0.01 to 99.99 KHz)
AC MICRO-AMP / MILLI-AMP/AMP MEASUREMENTS DISPLAY: 4 digit, 7 seg, LED of 13 mm(H) SIGNAL INPUT : 2.5V AC to 1000V AC.
3.5 Digit Panel / Portable Meters TIME BASE : Quartz Crystal Oscillator ACCURACY : 0.01% 1 count
Range Model Input SAMPLE TIME : 1 Second RESOLUTION: 0.01/0.1/1Hz/0.01KHz
Panel Portable Resolution Accuracy Impedance AUX SUPPLY: 230 10% volts AC, 50Hz, 1 Phase AC Mains
0 to 200 mA AC 34A54 34P54 / 36P54 0.1 mA 1KW SIZE & WEIGHT (approx):Panel cutout 46 mm (H) x 92 mm(W) with cabinet size
0 to 2mA AC 34A55 34P55 / 36P55 0.001mA 100W of 48 mm (H) x96mm (W) x 75mm(D), 400gms Panel mtg hardware is provided
0 to 20mA AC 34A56 34P56 / 36P56 0.01mA 0.5% 2 10W
0 to 200mA AC 34A57 34P57 / 36P57 0.1mA counts 1W
0 to 2A AC 34A58 34P58 / 36P58 0.001A 01W DPM MODULES
0 to 10A AC 34A59 34P59 / 36P59 0.01A 0.01W (3.5 digit LED / LCD modules with Bezel)
Higher currents 34A62 --- / --- Ext. CT CT Res. OEM modules to be fitted in your cabinet / equipment
MAINS (LINE) FREQUENCY MEASUREMENTS (4 DIGIT) 35 LED (200mV DC)
Range of Model No.
Resolution Accuracy 35 LCD (200mV DC)
measurement Panel Portable AUX SUPPLY: 5V DC
30.00 to 70.00 Hz 34A81 ----- 0.01 Hz 0.05Hz 1 counts SIZE & WEIGHT (approx): 72mm(W)
x 44mm(H) x < 40 mm(D) 60gms
Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 16 -
LCR DECADE BOXES RHEOSTATS
ACCESS RA series

RESISTANCE DECADE BOX


ACCESS RDB6

CAPACITANCE DECADE BOX


ACCESS CDB6
Useful as Variable Electrical Resistors / Load for testing in Industries, Laboratories, Schools &
Colleges. Hand Sliding Arm type with Resistance wire wound on a porcelain tube (core) fitted
INDUCTANCE DECADE BOX between two Aluminium end supports.
Model Number
ACCESS LDB6 Resistance Value / Size of Core Weight
Model Number
Current Capacity Length(mm) x (Kgs)
Dia(mm) (approx) (approx)
ACCESS 5R20A 5 ohms, 20 Amps 560 x 90 5
ACCESS 2R20A 2 ohms, 20 Amps 380 x 76 3.5
ACCESS 1R20A 1 ohms, 20 Amps 305 x 50 1.5
ACCESS 3R20A 0.3 ohms, 20 Amps 152 x 35 0.6

ACCESS 10R15A 10 ohms, 15 Amps 560 x 100 6


ACCESS 5R15A 5 ohms, 15 Amps 455 x 76 3.5
ACCESS 2R15A 2 ohms, 15 Amps 360 x 50 2
ACCESS 6R15A 0.6 ohms, 15 Amps 305 x 35 1.5

ACCESS LCR Decade Boxes are light weight ACCESS 20R10 20 ohms, 10 Amps 560 x 90 4.5
table top instruments for obtaining precision
values of resistors, capacitors and inductors. ACCESS 10R10A 10 ohms, 10 Amps 467 x 76 3.2
High quality ceramic encased wire wound and ACCESS 4R10A 4 ohms, 10 Amps 305 x 50 1.2
sputtered metal film resistors, metalized ACCESS 1.25R10A 1.25 ohms, 10 Amps 152 x 35 0.6
polyester and polystyrene capacitors and high
stability pot cores inductors, provide high ACCESS 100R5A 100 ohms, 5 Amps 560 x 100 5
performance. Special quality switches ensure
low contact resistance and smooth operations. ACCESS 60R5A 60 ohms, 5 Amps 455 x 90 4
ACCESS 25R5A 25 ohms, 5 Amps 360 x 50 1.5
ACCESS RDB6 ACCESS 12R5A 12 ohms, 5 Amps 305 x 35 1
RESISTANCE DECADE BOX ACCESS 5R5A 5 ohms, 5 Amps 152 x 35 0.5
RANGE: 1 ohm to 1.111111 mega ohms in 6
decades
ACCESS 500R2A 500 ohms, 2 Amps 560 x 90 5
ACCURACY: 1% 0.5 ohms
WATTAGE: 3 Watts for values below 10 ohms, ACCESS 200R2A 200 ohms, 2 Amps 380 x 76 2.2
watt from 10 ohms to 1 kilo ohms and watts ACCESS 100R2A 100 ohms, 2 Amps 305 x 50 1.2
for values more than 1 kilo ohms. ACCESS 45R2A 45 ohms, 2 Amps 228 x 35 0.6
PROTECTION: Fuse protection of 100 mA.
ACCESS 2.5KR1A 2.5 Kohms, 1 Amps 560 x 100 4.5
ACCESS CDB6
ACCESS 1KR1A 1 Kohms, 1 Amps 407 x 78 2.2
CAPACITANCE DECADE BOX
RANGE : 10 Pico Farads to 11.11111 micro ACCESS 600R1A 600 ohms, 1 Amps 360 x 50 1.2
farads in 6 decades ACCESS 300R1A 300 ohms, 1 Amps 305 x 35 0.8
ACCURACY: 1% 50 Pico farads . ACCESS 125R1A 125 ohms, 1 Amps 152 x 35 0.5
MAXIMUM WORKING VOLTAGE: 100 Volts
DC or 63 Volts AC
ACCESS 25KR.3A 25 Kohms, 0.3 Amps 560 x 100 4.5
ACCESS LDB6 ACCESS 10KR.3A 10 Kohms, 0.3 Amps 407 x 76 2.2
INDUCTANCE DECADE BOX ACCESS 4.5KR.3A 4.5 Kohms, 0.3 Amps 305 x 50 1.2
RANGE : 10 micro Henry to 11.11110 Henry in 6 ACCESS 2KR.3A 2 Kohms, 0.3 Amps 228 x 35 0.6
decades ACCESS 1.3KR.3A 1.3 Kohms, 0.3 Amps 152 x 35 0.5
ACCURACY: 2 % 5 micro Henry
PROTECTION : fuse protection of 500 mA. As per ITI new syllabus of Electrical Trade
SIZE & WEIGHT (approx):290mm (L) x 80 mm ACCESS 1R5A 0-1 ohms, 5 Amp 152 x 35 0.5
(W) X 110 mm (H), 1 KG (approx) ACCESS 10R5A 0-10 ohms, 5 Amp 305 x 35 1
ACCESS 25R1A 0-25 ohms, 1 Amp 152 x 35 0.5
ACCESS 300R1A 0-300 ohms, 1 Amp 152 x 35 0.5
Note: Other models / ranges available
Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 17 -
VARIACS (AIR COOLED)
(DIMMERSTATS / AUTO TRANSFORMERS)
Single Phase, Input 240V AC, Output 0 to 270V AC Three Phase, Input 415V AC,
Output 0 to 1470V AC
Current Portable (close) type Portable (close) type
Flush (Open) type
Rating (desk top model)
(panel mounting) (desk top models)
(amps)
Model No. Weight Model No. Weight Model No. Weight
1 amp V1F1 2.5Kgs V1P1 3.8Kgs V1P3 14Kgs
2 amp V2F1 2.9Kgs V2P1 4.2Kgs V2P3 14Kgs
3 amp V3F1 3.3Kgs V3P1 4.6Kgs V3P3 16Kgs
4 amp V4F1 5.9Kgs V4P1 6.9Kgs V4P3 26Kgs
5 amp V5F1 6.5Kgs V5P1 7.5Kgs V5P3 28Kgs
8 amp V8F1 8 Kgs V8P1 9 Kgs V8P3 32Kgs
10 amp V10F1 9 Kgs V10P1 10 Kgs V10P3 35Kgs
15 amp V15F1 13 Kgs V15P1 18 Kgs ---- ----
20 amp V20F1 15 Kgs V20P1 16 Kgs ---- ----
NOTE: 0.75A open type 1 phase small AE type is available for OEM

1 PHASE : Input : 240V AC & Output : 0 to 270V AC continuous LOW OPERATING TORQUE: Glass smooth commutator, special sintered
3 PHASE : Input : 415V AC & Output : 0 to 470V AC continuous bushings for shaft and perfect assembly of coils, results in low operating torque
RUGGED CONSTRUCTION: For maximum life SMOOTH VOLTAGE VARIATIONS: Voltage between turns is small &brush-
EXCELLENT REGULATION: Minimum drop in voltage at full load arm is in constant contact with more than one turn, avoiding harmful sparking
HIGH EFFICIENCY: Low loss due to careful copper & core LOW MAGNETIZING CURRENT: High quality grain oriented silicon steel
selection ensures minimum iron losses. No load current is less than 5% of the full load
NO WAVE FORM DISTORTION: Variac provides an output current
voltage, distortion less replica of the input voltage NEGLIGIBLE MAINTENANCE AND TROUBLE - FREE LONG LIFE:
SILVER PLATED COMMUTATOR: Special silver plating used on Inspection and maintenance are needed mainly for carbon tips and commutator.
the commutator helps withstand high overloads, constant contact Timely cleaning / replacement ensures a considerably long, maintenance-free
drop, smooth operation, long life & better resistance to corrosion and uninterrupted life to the variacs.

SINGLE PHASE OPEN TYPE (FLASH MOUNTING) f


A
Type A C E F G H
C Carbon Holder V1F1 110 92 10 6 25 80 7.5
Nylon Brush V2F1 110 92 10 6 25 95 7.5
H
Brush Arm V3F1 110 92 10 6 25 115 7.5
C

F
V4F1 175 146 25 6 35 102 10
Fixed Contact
20f knob V6F1 175 146 25 6 35 110 10
f
E

G V8F1 175 146 25 6 35 130 10


TENSION SPRING
V10F1 175 146 25 6 35 135 10
V15F1 225 176 25 10 35 135 11
V20F1 225 176 25 10 35 145 11
SINGLE PHASE PORTABLE (CLOSED TYPE)
A
Hole

C
A H Type A C E H f
V4P1 175 146 35 160 10
V6P1 175 146 35 160 10
E
V8P1 175 146 35 180 10
C
V10P1 175 146 35 180 10
V1P1 has rectangular box of 120mm(H) x 130mm(W) x 100mm(D) V15P1 225 176 40 190 11
V2P2 and V3P3 have rectangular boxes of 160mm(H) x 140mm(W) x 140mm(D) V20P1 225 176 40 190 11

THREE PHASE PORTABLE (CLOSED) :

Type W D H G Approx
Weight
G
V1P3 150 330 30 14 Kg
V2P3 180 330 30 14 Kg
V3P3 180 330 40 16 Kg
H
V4P3 250 425 40 26 Kg
V6P3 250 425 40 30 Kg
* V8P3 250 425 40 32 Kg
W
D V10P3 250 425 40 35 Kg

Note: Other models / ranges available


Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 18 -
TRAINERS
LINEAR IC TRAINER DIGITAL IC TRAINER DISCRETE COMPONENT
(ANALOG IC TRAINER) (DIGITAL LOGIC TRAINER) TRAINER
(BASIC ELECTRONICS TRAINER)
ACCESS LICT01 ACCESS DICT01 ACCESS DCT01

The Linear IC Trainer is intended for study, The Digital IC Trainer is intended for study, The Discrete Component Trainer is intended for
understanding & demonstrate various experiments understanding & demonstrate various experiments study, understanding & demonstrate various
covering different Linear ICs such as Op-amps & Timer covering different digital circuits by solderless experiments covering characteristics & applications
by solderless interconnections through use of 2 mm interconnections through use of 2 mm brass of different discrete components by solderless 2mm
brass terminations and patch cords terminations and patch cords brass terminations and patch cords
The trainer is housed in an elegant & sturdy plastic The trainer is housed in an elegant & sturdy plastic The trainer is housed in an elegant & sturdy plastic
cabinet and consists of mimicked different active/ cabinet and consists of mimicked digital ICs & blocks cabinet and consists of mimicked different active /
passive components / blocks such as Op-Amp IC DC Regulated Power Supply : 5V / 500 mA passive components & blocks such as Diodes
741(3), Timer IC 555 with trigger, Diodes 1N4007(1), Low frequency variable clock generator: One 1N4007(4), OA79(Ge), Zeners(3), LEDs(2), one
1N4148(2),Zeners(2),LED(1), assorted values of Pulser : One independent bounceless manual pulser each of Diac, Triac, UJT, SCR, JFET, MOSFET,
resistors (15) & capacitors (6) Logic Level Inputs : 8 ind. logic level inputs to select SL100 & SK100 Transistors, LDR, Thermistor,
Variable Resistor (pot) : 10K (1) High/Low TTL levels, each with LED indications inductors(2), Resistors(11), capacitors(10) &
DC Regulated Power Supplies : Logic Level Indicators: 8 independent logic level Buzzer(1)
a. Fixed :+/-15V/150mA indicators for High / Low status of digital outputs Var R (pots) : 3 (1K, 10K, 100K) Conn Strips : 3
b. Variable : 0 to 5V/ 150mA and 0 to 12V/150mA BCD to 7 Segment Decoder/ Driver with Display:1 DC Regulated Power Supplies :
Breadboard : 840 tie points Logic Probe : 1 ZIF socket : 20pin a. Fixed :5V/150mA and +/-12V/150mA
Power On : Power ON switch with indicator for mains Gates : OR, AND, NOT, NAND, NOR, EX-OR (4 each) b. Variable : 0 to 5V/ 250mA and 0 to 12V/250mA
ON indication and fuse for protection. Power On : Switch with indicator and fuse AC Supply : 15 0 15 V / 150 mA
Power Requirement : 230V +/- 10% 1phase AC Power Requirement : 230V +/- 10% 1phase AC Power On : Switch with indicator and fuse
SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x Power Requirement : 230V+/- 10% 1phase AC
100mm (H), 1.5 Kg. 100mm (H), 1.5 Kg. SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x
Accessories : Set of 10 stackable patch cords & Accessories: Set of 10 stackable patch cords & 100mm (H), 1.5 Kg.
Detailed Instruction manual Detailed Instruction manual Accessories : Set of 10 stackable patch cords &
Detailed Instruction manual
ANALOG COMPONENT OP-AMP TRAINER DIGITAL & ANALOG
TRAINER BREADBOARD TRAINER
ACCESS ACT01 ACCESS OPT01 ACCESS DABT01

The Analog Component Trainer is intended for study, & The Op-Amp Trainer is intended for study, The Digital and Analog Bread Board Trainer is
demonstrate various experiments covering understanding & demonstrate various experiments useful for all types of experiments without soldering
characteristics & applications of analog components covering Op-amps & Timer by solderless The trainer is housed in an elegant & sturdy plastic
by solder less 2 mm brass terminations & patch cords interconnections through use of 2 mm brass cabinet and consists of a large breadboard and
The trainer is housed in an elegant & sturdy plastic terminations and patch cords mimicked necessary associated blocks to perform
cabinet and consists of mimicked different analog The trainer is housed in an elegant & sturdy plastic various experiments
active / passive components & blocks such as Diodes cabinet and consists of mimicked different active / Breadboards : 1680 tie-points
4x1N4007 Rectifier, 1xOA79 Germanium, 3xZeners, passive components & blocks such as 3xOp Amp IC Pulse Generator : Clock 0-10 Hz Single - 1
2xLEDs, one each of Diac, Triac, UJT, SCR, JFET, 741, Timer IC 555 with trigger, Diodes 1x1N4007, Logic probe : 1 Variable Resistance (Pot) : 1
MOSFET, SL100 / SK100 Transistors, LDR, 2x1N4148, 2xZeners, 1xLED, assorted values of Digital input logic Hi/Lo switches with Ind : 4
Thermistor, 2xinductors, assorted values of resistors, resistors(15) & capacitors(6) Digital output indicators: 4
capacitors & Buzzer Var Resistor(pot) : 1 Switches : 2 (SPDT & DPDT) DC Regulated Power Supplies :
DC Regulated Power Supplies : DC Regulated Power Supplies : a. Fixed : 5V/100mA & +/-12V/100mA
a. Fixed :5V/150mA and +/-12V/150mA a. Fixed :+/-15V/150mA b. Variable : 0 to 15V / 100mA
b. Variable : 0 to 5V/ 250mA and 0 to 12V/250mA b. Variable : 0 to 5V/ 150mA and 0 to 12V/150mA AC Power Supplies: 15 0 15 V AC / 100mA
AC Supply : 15 0 15 V / 150 mA Power On : Power ON switch with indicator for mains Power On : Switch with indicator and fuse
Breadboard: 640 tie points Connecting Strips: 3 on indication and fuse for protection Power Requirement : 230V +/- 10% 1phase AC
Power On : Switch with indicator and fuse Power Requirement : 230V +/- 10% 1phase AC SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x
Power Requirement : 230V +/- 10% 1phase AC SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x 100mm (H), 1.7 Kg.
SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x 100mm (H), 1.5 Kg. Accessories : Set of 4 stackable patch cords, 6
100mm (H), 1.5 Kg. Accessories : Set of 10 stackable patch cords & stackable to hookup & 2 Mtr Hookup wire & Detailed
Accessories : Set of 10 stackable patch cords & Detailed Instruction manual Instruction manual
Detailed Instruction manual
Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 19 -
TRAINERS
ANALOG COMMUNICATION DIGITAL COMMUNICATION
AMPLITUDE MODULATOR FREQUENCY MODULATOR PAM / PWM / PPM
& DEMODULATOR & DEMODULATOR MODULATION /
TRAINER KIT TRAINER KIT DEMODULATION TRAINER
ACCESS AMDT01 ACCESS FMDT01 ACCESS PPPT01

The Amplitude Modulator & Demodulator Training Kit The Frequency Modulator & Demodulator Training Kit The PAM / PWM / PPM Modulation & Demodulation
is useful in study, understanding & performing the is useful in study, understanding & performing the Trainer is multi-experiment trainer for different
experiments by solderless 4 mm brass terminations experiments by solderless 4 mm brass terminations Digital Communication experiments by solderless 4
and patch cords and patch cords mm brass terminations and patch cords
The trainer is housed in an elegant & sturdy plastic The trainer is housed in an elegant & sturdy plastic The trainer is housed in an elegant & sturdy cabinet
cabinet and consists of mimicked dedicated circuits / cabinet and consists of mimicked dedicated circuits / and consists of mimicked dedicated circuits / blocks
blocks for performing experiments such as : blocks for performing experiments such as : for performing experiments such as :
- Study of Modulating Signal - Study of Modulating Signal - PAM - Pulse Amplitude Modulation & Demod
- Study of Carrier Signal - Study of Carrier Signal - PWM - Pulse Width Modulation & Demodulation
- Study of Amplitude Modulation - Study of Frequency Modulation - PPM - Pulse Position Modulation & Demod
- Study of Amplitude Demodulation - Study of Frequency Demodulation AF (Modulating) Signal Generator : 1 or 2 KHz
AF (Modulating) Signal Generator : 1 to 2 KHz AF (Modulating) Signal Generator : 1 or 2 KHz (selectable) with variable amplitude
(variable frequency) with variable amplitude (selectable) with variable amplitude Carrier (Sampling) Frequency : 8KHz, 16KHz,
Carrier Signal Generator : 100 KHz ( Var. amplitude) Carrier Signal Generator : 100 KHz ( Var. amplitude) 32KHz & 64 KHz
Amplitude Modulator & Demodulator : Inbuilt Frequency Modulator & Demodulator : Inbuilt DC Regulated Power Supplies :
DC Regulated Power Supplies : +/- 12 VDC DC Regulated Power Supplies : +/- 12 VDC Fixed :+/-12V & +5V / 250mA
Power On : Switch with indicator and fuse Power On : Switch with indicator and fuse Power On : Switch with indicator and fuse
Power Requirement : 230V +/- 10% 1phase AC Power Requirement : 230V +/- 10% 1phase AC Power Requirement : 230V +/- 10% 1phase AC
SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x SIZE & WEIGHT (approx) :255 mm (L) x 335 mm (W) x
100mm (H), 1.5 Kg. 100mm (H), 1.5 Kg. 100mm (H), 1.5 Kg.
Accessories : Set of 4 stackable patch cords & Accessories : Set of 4 stackable patch cords & Accessories : Set of 4 stackable patch cords &
Detailed Instruction manual Detailed Instruction manual Detailed Instruction manual

FIBRE OPTIC STEPPER MOTOR WITH WHEATSTONE'S BRIDGE


COMMUNICATION TRAINER DIGITAL CONTROLLER WITH GALVANOMETER & BATTERY

ACCESS FOT01 ACCESS STDC01 ACCESS WBT01

The Fibre Optic Communication Trainer is a useful, Stepper Motor with Digital Controller is useful in the The Wheatstone's Bridge with Galvanometer &
low-cost Optical Fibre based Voice Communication study & working of a stepper motor with digital control Battery is a useful, low-cost self contained
Training System. 2mm brass terminations provided The trainer is housed in an elegant & sturdy plastic dedicated trainer kit to find the value of unknown
The trainer is housed in an elegant & sturdy plastic cabinet & consists of mimicked dedicated components resistance, by solderless interconnections through
cabinet and consists of mimicked dedicated circuits / /blocks. 2mm terminations are provided use of 4mm brass terminations & patch cords
blocks with necessary test points Stepper Motor : Bi-directional, PM rotor & bifilar stator The trainer is housed in an elegant & sturdy plastic
Experiments : - Study of basic FO Tx & Rx Motor Characteristics : Self starting, low moment of cabinet & consists of mimicked dedicated
- Setting up of Simplex Analog Voice Link via FO inertia, instantaneous start, stop and rotation reversal components etc as follows :
- Study Tx & Rx circuits & observe signal on LED Rotation : 200 Steps / revolution Various fixed & variable resistor arms
Tx side : Mic, Input Amplifier, Tx & FO LED (660nm) Stepping Angle : 1.8 deg Analog Galvanometer for null detection
Rx side : FO Receiver (660nm), Low Pass Filter, AC Control : Versatile solid state electronic digital control DC Regulated Power Supply : +5V DC / 100mA
Amplifier with Gain adj, Power Amplifier & Speaker Output : Pulse pattern for driving the stepper motor Facility to select DC input to bridge, i.e., Internal
Fibre Optic (FO) cable:1meter with termination Types of Control : 1. Steps 2. Speed & 3. Direction Low Voltage DC (from mains) or External (Battery)
DC Regulated Power Supplies:+/-12V /150mA Pulser : Bounceless manual pulser Power On: Power ON switch with indicator for
Sine Generator : 1KHz (variable amplitude) Clock Generator: Variable clock frequency generator mains on indication & fuse for protection
Power On : Power ON switch with indicator for mains Power On: Power ON switch with indicator for mains Power Requirement : 230V +/- 10% 1phase AC
on indication and fuse for protection on indication & fuse for protection SIZE & WEIGHT (approx) :255 mm (L) x 335 mm (W) x
Power Requirement : 230V +/- 10% 1phase AC Power Requirement : 230V +/- 10% 1phase AC 100mm (H), 2 Kg.
SIZE & WEIGHT (approx) :205 mm (L) x 330 mm (W) x SIZE & WEIGHT (approx) :230 mm (L) x 280 mm (W) x Accessories : Set of 10 stackable patch cords, 9V
100mm (H), 1.5 Kg. 100mm (H), 2 Kg. Battery & Detailed Instruction manual
Accessories : Microphone, Set of stackable patch Accessories : Mains cord & Detailed Instruction
cords & Detailed Instruction Manual manual

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 20 -
TRAINERS
POWER ELECTRONICS TRAINER SENSOR TRAINER KIT - 1 SENSOR TRAINER KIT - 2
(WITH 6 ONBOARD APPLICATIONS) (WITH 4 SENSORS) (WITH 4 SENSORS)
ACCESS PET01 ACCESS STK01 ACCESS STK02

The Power Electronics Trainer with 6 Onboard ACCESS STK01, Sensor Trainer Kit - 1 is a modularly ACCESS STK02, Sensor Trainer Kit - 2 is a
(dedicated) applications is a user friendly ready to use designed training kit with 4 different sensors, sources, modularly designed training kit with 4 different
applications based trainer, using different power electronic instrumentation, necessary jig & display. sensors, sources, electronic instrumentation,
components by solderless 4mm shockproof brass 2mm brass terminations & patch cords n e c e s s a r y j i g & d i s p l a y. 2 m m b r a s s
terminations and patch cords The trainer is housed in an elegant & sturdy plastic terminations & patch cords
The trainer is housed in an elegant, sturdy cabinet and cabinets and consists of mimicked dedicated circuits / The trainer is housed in an elegant & sturdy
consists of mimicked different dedicated applications blocks with necessary test points. The various sensors plastic cabinets and consists of mimicked
using MOSFET, UJT, Triac, Diac, LDR, SCR, IGBT, Pulse covered are : dedicated circuits / blocks with necessary test
Tx 1:1, IC 555, IC 324, Diodes, R(fix/var) & C as required Thermal / Temperature Sensors with water heater points. The various sensors covered are :
Experiments: To study & perform, 1. Thermocouple Strain / Load Sensors
1) AC phase control using SCR 2. Thermistor 1. Strain Gauges mounted on cantilever beam
2) Lamp intensity control using Triac and Diac 3. RTD and 2. Load Cell mounted on cantilever beam
3) Light activated solid state switch using Triac and Diac with weights
4) UJT Relaxation Oscillator and Controlled Rectifier Special Purpose Sensor : Displacement (Linear / Angular)
5) PWM Speed control of DC Motor Using IGBT 4. Smoke Sensor 3. Linear - LVDT
6) Speed Control of DC Motor Using MOSFET 4. Angular - Speed sensor and a motor with
Loads : AC Lamp & DC Motor Power On : Power ON switch with indicator for mains variable speed control
DC/AC Supplies : +15VDC/250mA ;12VAC & Mains O/P on indication and fuse for protection Power On : Power ON switch with indicator for
Power On : Power ON switch with indicator for mains on Power Requirement : 230V +/- 10% 1phase AC mains on indication and fuse for protection
indication and fuse for protection SIZE & WEIGHT (approx) :255 mm (L) x 330 mm (W) x Power Requirement : 230V +/- 10% 1phase AC
Power Requirement : 230V +/- 10% 1phase AC 100mm (H), 2.3 Kg. SIZE & WEIGHT (approx) :255 mm (L) x 330 mm
SIZE & WEIGHT (approx) :310 mm (L) x 410 mm (W) x Accessories : Set of 2 stackable patch cords & (W) x 100mm (H), 4 Kg.
165mm (H), 3.5 Kg. Detailed Instruction manual Accessories : Set of 4 stackable patch cords
Accessories : Set of 6 stackable patch cords & Detailed & Detailed Instruction manual
Instruction manual

SMPS TRAINER UPS TRAINER PLC TRAINER


ACCESS SMPST01 ACCESS UPST01 ACCESS PLC-01

ts &
8 Inputputs
4 Ou

The SMPS Trainer is intended for study, understanding & The UPS (Uninterrupted Power Supply) Trainer is PLC Trainer is useful for study, understanding &
demonstrate the principle & working of a Switch Mode useful in the study and demonstration of PWM, AVR, demonstration of various experiments covering
Power Supply (SMPS), with different input voltages, with overall functioning of UPS with and without load. Non PLC (Programmable Logic Control) by
or without load. Digital Voltmeter & Current meter are destructive Fault creating facilities are also provided solderless interconnections. The trainer is
provided. The trainer is housed in an elegant & sturdy cabinet housed in an elegant & sturdy plastic cabinet &
The trainer is housed in an elegant & sturdy plastic and consists of mimicked dedicated circuits / blocks consists of mimicked different blocks such as :
cabinet and consists of mimicked dedicated circuits / with test points to observe the waveforms and voltages Inputs : 6 Digital (DI) & 2 Analog(AI) or 8 DI
blocks with 4mm test points to observe the waveforms & Input : 190 to 260 V 10%, 50 Hz Output : 230 V Outputs : 4 Digital (DO) (relay based)
voltages. Type : Offline Display : LCD backlit
Input : 180 to 240V AC in steps through switch Transformer : Multi tapped AVR type DC Supply : 24V/1A
Output : +5V, +12V & -12V DC (Separate ) Battery : 12 V (provided) Hi / Lo Inputs : 6 with individual LED Indications
Meters : 20VDC Voltmeter & 2ADC Ammeter Faults : Non destructive provided (4 toggle & 2 Push to Hi Switches )
Load: Bulb load (2 nos.) Indicators : Audio & Visual provided Analog Input : 2 Variable voltages
Power On : Power ON switch with indicator for mains on Load : Bulb Holder & Socket Provided Output Indicators : 4(LED) & 1(audio)
indication and fuse for protection Power On : Switch with indicator and fuse Power On : Power ON switch with indicator for
Power Requirement : 230V +/- 10% 1phase AC Power Requirement : 230V +/- 10% 1phase AC mains on indication and fuse for protection
SIZE & WEIGHT (approx) :255 mm (L) x 335 mm (W) x SIZE & WEIGHT (approx) :210 mm (L) x 390 mm (W) x Power Requirement : 230V +/- 10% 1phase AC
100mm (H), 3.5 Kg. 115mm (H), 6.5 Kg. Accessories : Ladder diagram software CD,
Accessories : Set of 4 stackable patch cords & Detailed Accessories : Detailed Instruction manual basic sample ladder programmes, PLC to PC
Instruction manual interfacing cable, set of 12 stackable patch
cords & Detailed Instruction manual

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 21 -
TRAINERS
8085 MICROPROCESSOR MICROCONTROLLER KIT (8051) APPLICATION KIT FOR
TRAINER (Assembly level Programming) MICROCONTROLLER
(6 Different Applications)
ACCESS M8501 ACCESS M5101 ACCESS M51AK6

CPU : 8085 CPU operating at 6.144 Mhz CPU : 8051/89C51 CPU operating @10/12MHz Kit can be used alone or with ACCESS M5101
ROM : 8K bytes of ROM using 27512 EPROM ROM : 16K bytes using 27512 EPROM The Application Kit for Microcontroller is a self
RAM : 8K bytes of RAM using 6264 with NiCD Battery RAM : 8K bytes of RAM using 6264 with NiCD Battery contained kit for study & performing experiments
Backup & memory expandable upto 56KB backup & Memory expandable up to 64KB on 8051 Microcontroller & applications
BACKUP : NICD Battery & expandable TIMER/COUNTER : Three Channel Timer/Counter The trainer is housed in an elegant & sturdy
TIMER/COUNTER : 3 Channel 16 bit Timer / Counter using 8253 brought out at 10 Pins FRC Connector plastic cabinet and consists of mimicked
using 8253 at 10 Pins FRC Connector I/O LINES : 48 I/O lines provided through 8255 dedicated blocks
I/O LINES : 24 I/O lines provided through 8255 brought brought out at 26 Pins FRC Connector MICROCONTROLLER : 8051 with 4 Input ports
out at 26 Pins FRC Connector RS232C INTERFACE : Using 8251 brought out at 9 PROGRAMMING : Serial through ISP Interface
RS232C INTERFACE : Serial interfacing through Pins D-Type Connector (PC Interface) & External via ACCESS M51-01
SID/SOD lines MODES OF COMMANDS : Keyboard & Serial Mode APPLICATIONS :
MODES OF COMMANDS : Hex Keypad & Serial DISPLAY : 6 Digit 7 Segment Display using 8279 1) 16X2 LCD Display 2) 8 bit LED Display
DISPLAY : Six Digit Seven Segment Display KEYBOARD : 25 Keys Hex Keypad using 8279 3) 4 multiplexed Seven Segment Display
KEYBOARD : 28 Keys Hex Keypad using 8279 Keyboard Display Controller 4) 4 Bit Input push button switches
Keyboard Display Controller DOWNLOADING/UPLOADING : Facility for 5) 2 channel (opto isolated) Relay application
DOWNLOADING / UPLOADING : Facility for Downloading / Uploading files from / to PC 6) Buzzer application 7) Serial Communication
downloading / uploading files from / to PC BUS : All address, data & control lines are available on POWER ON : Switch with indicator and fuse
BUS : All address, data & control signals / lines are KXT Bus 40 pins & 20 pins FRC Connector POWER REQUIREMENT : 230V +/- 10%
available on KXT Bus 50 pin FRC Connector POWER REQUIREMENT : 230V +/- 10% 1phase AC 1phase AC
POWER REQUIREMENT : 230V +/- 10% 1phase AC SIZE & WEIGHT (approx) :205 mm (L) x 280 mm (W) x SIZE & WEIGHT (approx) :225 mm (L) x 335 mm
SIZE & WEIGHT (approx) :205 mm (L) x 280 mm (W) x 100mm (H), 1 Kg. (W) x 100mm (H), 2 Kg.
110mm (H), 1 Kg. ACCESSORIES : Mains cord & Instruction manual ACCESSORIES : PC interfacing Cable, FRC
ACCESSORIES : Mains cord & Instruction manual Cables, Detailed Instruction manual, Evaluation
Software CD with programmes for PC

8086 MICROPROCESSOR AC & DC DRIVE TRAINERS EXTRA ACCESSORIES


TRAINER (with AC / DC motors)
ACCESS M8601 2mm to 2mm stackable patch cords
(Lengh: 0.5 mtr & Qty: 10
patch cords 5Red+5Black)
ACCESS AL205 (0.5mtr)

4mm to 4mm stackable patch cords


(Lengh: 0.5 / 1.0 mtr & Qty: 10
patch cords 5Red+5Black)

CPU : 8086 CPU operating at 2.5/5 MHZ AC & DC Drive Trainers are useful to study the advance ACCESS AL405 (0.5mtr)
ACCESS AL410 (1 mtr)
CO-PROCESSOR : Socket provided for 8087 & 8089 method of electronic control of AC & DC motors using
ROM : 16K bytes of ROM using 27512 EPROM Thyristors / IGBT. Various models with different
RAM : 16K bytes of RAM using 6264 with NiCD Battery facilities are available with detailed instruction manual. 4mm to Crocodile Test leads
Backup & expandable upto 256KB (Lengh: 1.0 mtr & Qty: 10
AC DRIVE: Thyristor / IGBT control ACCESS AD220 Test leads 5Red+5Black)
TIMER/COUNTER : 3 Channel Timer / Counter using
AC motor drive with VVVF control
8253 at 10 Pins FRC Connector ACCESS AL450 (1 mtr)
3phase, 2HP with 3phase 220V,
I/O LINES : 72 I/O lines provided through 8255 brought
2HP AC motor with educational
out at 26 Pins FRC Connector
terminals BNC to Crocodile Probe
RS232C INTERFACE : 8051 at 9 pin D connector
MODES OF COMMANDS : Hex Keypad & Serial (Lengh: 1.0 mtr & Qty: 1 probe
AC DRIVE: Thyristor / IGBT control ACCESS AD440 BNC Plug (M) to crocrodile
DISPLAY : EIght Digit Seven Segment Display
AC motor drive with VVVF control clips (Red+Black))
KEYBOARD : 28Keys Hex Keypad using 8279
3phase, 2HP with 3phase 440V, ACCESS AL50
Keyboard Display Controller
2HP AC motor with educational
DOWNLOADING / UPLOADING : Facility for
terminals
downloading / uploading files from / to PC BNC to BNC probe
BUS : All address, data & control signals / lines are (Lengh: 1.0 mtr & Qty: 1 probe
DC DRIVE: Thyristor / IGBT control ACCESS DD220
available on KXT Bus 50 pin FRC Connector BNC Plug (M) to BNC Plug (M))
DC motor drive with tacho-
POWER REQUIREMENT : 230V +/- 10% 1phase AC ACCESS AL60
SIZE & WEIGHT (approx) :205 mm (L) x 280 mm (W) x generator feedback arrangement 1
110mm (H), 1 Kg. hp with 220V, 1HP DC Shunt motor
Accessories : Instruction manual with educational terminals

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 22 -
TRANSFORMER DIGITAL PF & KW METERS RELAYS
SINGLE / THREE PHASE
Air Cooled Digital Power Factor (PF) Meter Cut Out Relay
Tx 1ph 1KVA ACCESS TX101 Reverse Current Relay
ACCESS 34A26
Tx 1ph 3KVA ACCESS TX103 Over Current Relay
Oil Cooled (Supplied without oil ; Oil cost extra) Digital Kilo Watt Meter (0-1-3KW/3000W)
Tx 3ph 3KVA ACCESS TX301 Under Voltage Relay
ACCESS 34A23
Tx 3ph 5KVA ACCESS TX501

Type PF Meter KW Meter Relays for various protection are available, working
on 230V AC mains
Model 34A26 34A23
Parameters pF P (Watt) Reverse Over Under
Relays Cut Out
Current Current Voltage
Measurement 500 V / 5A / 500 V / 5A /
Single phase Air Cooled: Core type ; Copper (Auto Ranging) 45-65 Hz 45-65 Hz System 1 phase / 2 wire
Backllite Top & BIT-15 terminations 1 KVA / 3KVA Parameter Cut Out Reverse Over Under
Primary : 230V AC Sec. : 0-12-24-50-115V AC Display Digital 4 digit, 7-seg LED Controlled Current Current Current Voltage
Three phase Oil Cooled: Shell type Size 48mm x 96mm (Cutout:44mm x 92mm) O/P Relay 1 1 1 1
Backllite Top & BIT-15 terminations 3 KVA / 3KVA
POWER REQUIREMENT: 90V to 270V AC, 50 Hz POWER REQUIREMENT: 220 V AC Mains, 50 Hz
Primary : 440V AC Sec. : 230V AC (Oil at extra cost)
Note: Other models / ranges available

STARTERS (AC) STARTERS (DC) KNIFE SWITCH


(Close Box Type) (Close Box Type) (Open type with fuse & terminals)
(for 2HP to 5HP AC motors) (for 1HP to 5HP DC motors)

Rotar Resistance Type Starter DC 2 Point Starter SPDT KNIFE SWITCH


ACCESS SR01 (for Slipring Motors) ACCESS SDC02 (for DC Series Motors) ACCESS KS01
Auto Transformer Type Starter DC 3 Point Starter DPDT KNIFE SWITCH
ACCESS SAT01 (for 3f Induction Motors) ACCESS SDC03 (for DC Shunt Motors) ACCESS KS02
DOL Starter (for 1f & 3f Motors) DC 4 Point Starter TPDT KNIFE SWITCH
Star Delta Starter (for 3f Motors) ACCESS SDC04 (for DC Compound Motors) ACCESS KS03
INPUT SUPPLY: 220 V DC, 50 Hz Knife switch SPDT/ DPDT & TPDT fitted with fuse
ii) Semi-automatic SIZE & WEIGHT (approx): 205mm(D) x terminals all mounted on an open backlite sheet
iii) Automatic 225mm(W) x 240mm(H), 2.3 Kg. Approx with shoes
CAPACITY: 20A

BATH IMPREGNATING BATTERY CHARGER INDUCTION COIL


MACHINE (Laboratory Type)
ACCESS BI07 12V / 3A ACCESS IC10
6 to 24V / 10A
6 to 48V / 10A

Bath Impregnating Machine is used to close / APPLICATION : Charging of Dry & Lead Acid ACCESS IC10 Laboratory Type Induction coil
seal the cavities between windings for better Batteries (Spark Coil) is a special type of transformer used to
electrical insulation, thermal conductivity. The TYPE: Transformer with basic rectification generate / produce intermittent high voltage pulses
preheated windings on the rotar / motor / VOLTAGE : Single or Multi output (Spark) from a low voltage DC supply
transformer / soleniods / coils is dipped in the CURRENT : 3 or 10A SPARK : 10mm (max) Adjustable
varnish kept in the Bath Impregnating Machine. AMMETER : Analog (1) INPUT SUPPLY : 6 - 8 V DC / 3A
FUSES : Provided SIZE & WEIGHT (approx): 148 mm (D) x 248 mm (W)
CONTROLS: Range/Fine control for voltage x 150 mm (H) , 1Kg
OUTPUT : Heavy duty binding posts
Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 23 -
Excise Duty Warranty Validity Jurisdiction Place of Origin
NIL 1 YEAR upto 30.06.2017 MUMBAI only MUMBAI

DELIVERY PERIOD: Normally within 1 week after realization of payments


FREIGHT: Extra ` 90/- Per Kg through courier. Minimum couriers freight charges are ` 200/-. Freight to pay
basis for dispatches through lorry
VALUE ADDED TAX (VAT) : Extra at 13.5% on all products; (except 6% on sine + square generators, current
transformers and variacs. for Maharashtra invoicing)
PAYMENT TERMS: 100% against Performa invoice by way of :
Demand draft favouring Access Technologies payable at Mumbai or
Deposit in our Current Account :-
Name of Account : Access Technologies
Current A/c Number : 546401010050487
Bank Name : Union Bank of India
Branch: Hiranandani Gardens, Powai, Mumbai - 400076
IFSC code : UBIN0554642
or Demand Draft or Cash payment against collection of material from our above address
VAT TIN NO: 27521146881V / CST TIN NO: 27521146881C

Looking forward for your valued purchase orders and thanking you

For ACCESS TECHNOLOGIES

a h
Paarth Sh
Authorised Signatory

Ordering made easy


1. Select the required products from the list above
2. Call / WhatsApp : +91-9819571964
3. Email : info@accesstech.co.in
4. Wait for our Proforma Invoice by mail
5.Upon receipt of our Proforma Invoice, courier us demand draft or at par cheque or
deposit amount in our Current Account (details as above) and mail us the deposit slip,
or collect material upon payment by cash or demand draft

The material will be dispatched to you directly through courier / lorry. We do not despatch
material by our person, railways, air, post office or angadias.

P.S. 1. We reserve our right to revise above data / price without prior intimation.
Taxes and levies may vary as per government rules.
2. We are manufacturers of ACCESS products and stockiest of remaining products.
3. Our rates and terms and conditions are not negotiable and we do not offer
discounts. Kindly treat this quotation as Final for placing orders.

Manufactured / Marketed by
ACCESS TECHNOLOGIES
C-107, Kailas Industrial Complex, Hiranandani Link Road, Park Site, Vikhroli (W), Mumbai - 400 079. INDIA
Phone : +91-22-25170633 / 25173338 Mob: +91-9819571964 E-mail : info@accesstech.co.in Website : www.accesstech.co.in
We reserve our right to revise the above data / price without prior information. VAT & Freight extra.
The rates are for supplies within INDIA & valid until 30.06.2017

- 24 -

You might also like