Professional Documents
Culture Documents
DEKOTEC-HTS
1. Preparation 2. Cleaning 3. Preheating of joint area 4. DEKOTEC-EP Primer application
All application steps have to be performed with Optional
proper personal protection equipment, such as +50C (+122F) +90C (+194F)
safety shoes, helmet, safety goggles and heat pro- with Primer without Primer
tection gloves, in accordance with local health and
safety regulations. A personal application training is
strongly recommend for people who are new to the
application of heat shrink sleeves!
Adjacent factory coating must be roughened (e.g.
emery cloth #40) and beveled with an angle 30.
For pipe diameters > 400mm (16) two
applicators are recommended.
Required surface cleanliness:
Surface has to be dry, free of grease, oil, dust and
other dirt before blast cleaning to a Use clean gloves and a lint-free cloth to ensure a Pre-heat the joint area uniformly (steel and adjacent Mix DEKOTEC-EP Primer components A and B in
minimum of SA 2 according to ISO 8501-1. Blast clean surface for an optimal application. mill coating) to +50C (+122F) before the applica- the ratio 2:1 (by volume) and stir for 1 minute.
cleaned surfaces have to be protected against the Never touch the blast cleaned surface with tion of DEKOTEC-EP Primer. If no DEKOTEC-EP Apply a thin and even layer of DEKOTEC-EP
influences of dust and moisture. bare hands! Primer is used, directly heat the surface to +90C Primer on the surface of the total joint area (steel
(+194F). Preheating is performed with a high and adjacent mill coating) with the rough (black)
intensity flame. side of a sponge.
5. DEKOTEC-EP Primer Curing 6. DEKOTEC-HTS Sleeve Installation 7. DEKOTEC-HTS Sleeve Installation 8. DEKOTEC-HTS Sleeve Installation
Optional Step 1 Step 2 Step 3 2h
+90 to +110 C 1.
+194 to +230 F 360
2. 2h 2.
2. 1. 1.
100 mm (4)
9. DEKOTEC-CLP 10. DEKOTEC-HTS Sleeve Installation 11. DEKOTEC-HTS Sleeve Installation 12. DEKOTEC-HTS Sleeve Installation
Closure Patch application Shrinking Postheating Smoothening
1.
2. 2.
DN >400
2. 2 torches! 2.
1.
1.
Heat the adhesive (silver) side of DEKOTEC-CLP Use a torch flame with medium intensity to shrink Heat the complete DEKOTEC-HTS heat shrink Use a roll to remove entrapped air. First roll circumfer-
closure patch until the surface becomes shiny. the DEKOTEC-HTS sleeve. sleeve homogeneously with a high intensity flame. entially to the overlap area of the shrink sleeve.
Apply the CLP in the overlapping area of the heat Heat the DEKOTEC-HTS sleeve starting from the The imprinting DEKOTEC vanishes when the In the overlap area start rolling from the middle to the
shrink sleeve, so that the centre markings are centre to its edges circumferentially around the sleeve was heated sufficiently. outer side. Use a zig-zag movement of the roll to drive
overlaid, and press it firmly to the surface. pipe, using constant and round movements. The adhesive has to be visible on both sides of the the air bubbles.
Avoid to stretch the CLP. For pipe diameters > 400 mm (16) use two torches sleeve around the circumference.
on opposite sides.
DENSO GmbH Our product information, our application recommendations and other product related change without notice. Our General Sales Conditions, which are available at
documents are made for your convenience only. Since many installation factors are www.denso.de, shall be decisive without any exception. 11/2015
P.O. Box 150120 | 51344 Leverkusen | Germany
beyond our control, the user shall determine the suitability of the products for the This is a translation from the original German Product Information of DENSO GmbH. In case of any discrepancy or any
Phone +49 214 26 02-0 | Fax +49 214 2602-217 intended use and assume all risks and liabilities in connection therewith. dispute arising on the interpretation of this Product Information, the german text of the respective German Product
www.denso.de | info@denso.de All information contained in this document is to be used as a guide and is subject to Information, which is available at www.denso.de, shall be decisive. The legal relationship shall be governed by German law.