Professional Documents
Culture Documents
com
X-Tower system
Experience the CUE DEE X-Tower System, Light weight yet strong and durable
The X-Tower is a modular tower system built in 4 m long sections with varying width.
This means we can optimize our tower to fit your exact needs and specs.
Content
THIS IS x-tower
2 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 3
01 INTRODUCTION
Four-sided self-supporting tower.
www.cuedee.com
Thank you for your interest in Thanks to the modular system of the X-Tower we can optimize it to fit your exact needs. Our tower-sections come
in 4 m lengths with a large variety of frame leg dimensions. This feature gives us a unique advantage in optimizing
our new and updated X-Tower our tower without increasing the actual footprint. We don’t preassemble the tower sections upon delivery, since we
feel it’s important to have an efficient transport solution.
4 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 5
02 Areas of use
Low weight yet strong and durable
LIGHT YET STRONG AND DURABLE load, structural movement etc. Depending on tower section we can
Tower overloading is becoming more of an issue nowadays since offer 3 different frame leg dimensions depending on required tower
operators want to add more equipment to existing and new sites as strength, you could call them light, medium and heavy duty.
technology evolves. To cope with this we decided to develop a light As an example the widest X-Tower section, the X-13 is available
yet strong and durable tower system. with Ø65, Ø70 and Ø75 mm frame legs. The X-Tower will probably
The sections are made from solid rod steel frame legs and the be used as a greenfield tower in most cases but some of our custo-
braces are all channel steel. We only use high grade steel to keep mers have come to use it as a wind turbine tower as well.
the tower weight at a minimum.
We also chose to add another smart feature to our tower in order INSTALLATION
to reduce weight; the tower frame legs are available in a number of When it comes to installation this can either be done manually with a
different dimensions gin pole or if you prefer with a crane.
Both ways has its advantages, for instance the site might not be
DESIGN POSSIBILITIES accessible with a crane then you have to rely on manual installation
Because we can offer the X-Tower with different frame leg dimen- to get the job done.
sions it’s possible to optimize each tower depending on height, wind
6 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 7
03 flexibility
Thanks to the modular design we can optimize the tower
Optimizing the X-Tower account when doing the structural calcula- on required tower strength, you could call
When we optimize the X-Tower we first need tion for the tower. them light, medium and heavy duty. As an
to know where it’s going to be installed and example the widest X-Tower section, the
how our customer intends to use it i.e. how Different design possibilities X-13 is available with Ø65, Ø70 and Ø75
much antennas will be mounted on it. We When the calculations are done we end up mm frame legs.
need to know this in order to accurately cal- with a basic tower configuration. But becau-
culate wind loads and terrain types. se we can offer the X-Tower with different fra- In some cases this feature gives us the pos-
For instance if a tower is located in an me leg dimensions it’s possible to optimize sibility to increase the frame leg diameter
open field it is likely to suffer higher wind each tower depending on height, wind load, and at the same time decrease the foot-
speeds then a tower located in a forest. Pla- structural movement etc. print. This can be very useful in urban areas
cing a tower on a hill also increase the wind Depending on tower section we can offer where site space is hard to come by.
load. All of these factors must be taken into 3 different frame leg dimensions depending
8 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 9
04 Quality & design
High quality materials are used
Both frame legs and bracing are made from high quality S355 steel.
www.cuedee.com
X-Tower cooperation
As we mentioned in the introduction we have started up a coopera-
tion with Elektroskandia in China. The tower production in China will
meet the same high standards that we have in Europe, we will also
meet the new SS-EN 1090 standard.
Elektroskandia will not only produce the towers but will also market
the tower system on the Asian market. We believe Elektroskandias
strong presence in the region will be beneficial for our customers in
terms of support and logistics etc.
Standards followed
As with all our products quality is of the utmost importance for us
so naturally we follow all existing standards. The tower design stan-
dards we follow are TIA 222-G, Eurocode 3, part 1-1, part 8 and
part 3-1 DIN V 4131. Of course in some countries there are specific
standards which are not covered by TIA or Eurocode. In those cases
we use the national standards such as the SNIP standard in Russia
The X-Tower is made of high quality galvanized steel. and Kazakhstan.
10
10 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 11
05 TECHNICAL
The X-Tower can be built in heights from 20 m up to 60 m
As with all our products quality is of the utmost importance for us.
www.cuedee.com
Technical information
The X-13 section is the widest
and strongest section on the X-Tower Optimal height: 20-60 m
Design Standards: TIA 222-G Eurocode 3, part 1-1, part 1-8 and part 3-1 DIN V 4131
The X-13 section is the widest and strongest section currently available to the X-Tower.
Materials: Legs: Ø345, Braces: Ø345
Connections: Bolts, nuts and washers class 8.8 according to EN ISO 4014, 4032 and 10,9 EN 14399-4
Anti corrosion treatment: All steel elements are hot-dip galvanised (ISO 1461).
Optional painting (red/white)
Ladder: Open or caged ladder with saftey climbing rail mounted inside or
outside vertical cable supports
Accessories: Work and rest platforms, antenna supports, anti-climb guard, fall protection,
obstruction light, lightning protection kit and door opening on bottom
section
available accessories
Depending on the desired width of the tower either the 0.75 m wide Of course having a light tower is also good when it comes to logis-
X1 or the 1.05 m wide X2 can be used as the straight top section. tics!
The straight X-1 and X-2 sections are available in both 2 and 4 m
lengths. The X-13 section is the largest section on the X-Tower with An example of a tailor made antenna Ladders and fall arrest systems are Obstruction light mounted on X-1 Work and rest platforms are available
carrier solution for the X-Tower. some of the accessories available to section. upon request.
a width of 4.35 m.
the X-Tower.
12 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 13
06 acessories
Brackets, obstruction lights and much more
single rru support double rru support triple rru support antenna support
prod.nr 5403 prod.nr 5406 prod.nr 5438 prod.nr 1763
The Single RRU Support is designed for instal- The Double RRU Support is designed for in- The Triple RRU Support is designed for instal- The Antenna Support is designed for installa-
lation of 1 RRU unit with possibility to attach a stallation of 2 RRU units with possibility to at- lation of 3 RRU units with possibility to attach tion of any kind of panel antennas, radio links
PSU on the back. tach a PSU on the back. a PSU on the back. up to Ø1,2 m (47,2 in).
1-L Link Support 2-L Link Support AIR antenna SUPPORT Parallel Cog Support
prod.nr 1981 prod.nr 1913 prod.nr 5861 prod.nr 5408
The 1-L Link Support is designed for installa- The 2-L Link Support is designed for instal- The AIR Antenna Support is designed for in- The Parallel Cog Support is designed for in-
tion of several small radio links or one large lation of several small radio links or one large stallation of one AIR unit or other common stallation of panel antennas and other com-
link up to Ø3,0 m (118 in) with strut support. link up to Ø2,6 m (102 in) with strut support. panel antennas on the market. mon telecom equipment such as RRU, TMA
etc.
14 X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” X-TOWER SYSTEM — CUE DEE ” your i n n o v a t i v e p a rt n er ” 15
www.cuedee.com