You are on page 1of 19

@A318/A319/A320/A321

TROUBLE SHOOTING MANUAL


** On A/C ALL
Task 24-00-00-810-818-A
Computer Reset
1. Possible Causes
REV. DATE : 01-Nov-2012

2. Fault Confirmation
A. Test
(1) Not applicable
3. Fault Isolation
A. Table of the circuit breakers used in this procedure:

PANEL DESIGNATION FIN LOCATION


** On A/C 001-100 201-300 351-500 551-700
49VU AIR COND/TEMP CTL/SYS 1 CHAN 52HH D08
B/28VDC
49VU COM/CIDS/FLT ATTND PNL/ESS 171RH H01
** On A/C 001-100 201-300 401-500 551-700
49VU COM/CIDS/DIR ESS/2 157RH G02
** On A/C 001-100 201-500 551-700
49VU COM/CIDS/DIR ESS/1 150RH G01
** On A/C 001-103 201-300 351-353 401-500
49VU AIR COND/AFT CARGO/VENT/CTL & 31HN C07
MONG
49VU AIR COND/AFT CARGO/VENT/CTL & 31HN C07
MONG
** On A/C ALL
49VU FUEL/FQI/CHAN/1 1QT A13
49VU ENGINE/2/FIRE DET/LOOP B 8WD2 A07
49VU ENGINE/1/FIRE DET/LOOP A 7WD1 A06
49VU ENGINE/2/FADEC A/AND EIU 2 2KS2 A05
49VU ENGINE/1/FADEC A/AND EIU 1 2KS1 A04
49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11
49VU FLIGHT CONTROLS/FCDC1/SPLY 20CE1 B10
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
49VU AUTO FLT/FCU/1 9CA1 B05
49VU AUTO FLT/FAC1/28VDC 5CC1 B04
49VU AUTO FLT/FAC1/26VAC 14CC1 B03
49VU AUTO FLT/FMGC/1 10CA1 B02
49VU AUTO FLT/MCDU/1 11CA1 B01
49VU L/G/LGCIU/SYS1/NORM 1GA C09
49VU AIR COND/CAB/PRESS/CTL1 1HL D09

JST Page 1
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

PANEL DESIGNATION FIN LOCATION


49VU EIS/DMC1/SPLY 10WT1 E11
49VU FWS/FWC1/SPLY 3WW F01
49VU NAV/MMR/1 42RT1 G12
** On A/C 101-150 301-350 501-550
REV. DATE : 01-Nov-2012

49VU AIR COND/SDCU/CHAN1 11WQ C06


** On A/C 101-150 501-550
49VU COM/CIDS/DIR 1 AND 2/ESS 150RH G02
** On A/C 104-150 301-350 354-400 551-700
49VU DUMMY CB 31HN C07
49VU DUMMY CB 31HN C07
** On A/C 301-400
49VU COM DIR ESS/2 157RH G02
** On A/C 501-550
49VU AIR COND/AFT CARGO/VENT & HTG/CTL 31HN C07
& MONG
49VU AIR COND/AFT CARGO/VENT & HTG/CTL 31HN C07
& MONG
** On A/C 001-050 101-150 201-203 301-350 501-700
121VU DUMMY CB 11CA3 N21
** On A/C 001-100 201-300 401-500 551-700
121VU COM NAV/CIDS/DIR NORM/2 156RH M06
121VU COM NAV/CIDS/DIR NORM/1 151RH M05
121VU COM/FAP1/NORM 170RH Q14
** On A/C 001-150 201-300 351-700
121VU ATSU 1 3TX1 L16
121VU ATSU 1/SWTG 5TX1 L15
** On A/C 001-150 201-301 351-700
121VU COM NAV/TCAS 4SG K10
** On A/C ALL
121VU COM NAV/RAD ALTM/2 1SA2 K12
121VU COM NAV/RAD ALTM/1 1SA1 K11
121VU APU/FIRE AND OVHT/DET/LOOP B 2WG L44
121VU APU/FIRE AND OVHT/DET/LOOP A 1WG L43
121VU COM NAV/MMR/2 42RT2 L07
121VU HYDRAULIC/BRAKING AND 4GG M36
STEERING/SYS2/SPLY
121VU HYDRAULIC/BRAKING AND 3GG M35
STEERING/SYS2/CTL
121VU HYDRAULIC/BRAKING AND 1GG M34
STEERING/SYS1/CTL

JST Page 2
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

PANEL DESIGNATION FIN LOCATION


121VU HYDRAULIC/BRAKING AND 2GG M33
STEERING/SYS1/IND AND/SPLY
121VU FUEL/FQI/CHAN/2 2QT M27
121VU AUTO FLT/FCU/2 9CA2 M21
121VU AUTO FLT/FAC2/28VDC 5CC2 M19
REV. DATE : 01-Nov-2012

121VU AUTO FLT/FAC2/26VAC 14CC2 M18


121VU AUTO FLT/FMGC/2 10CA2 M17
121VU AUTO FLT/MCDU/2 11CA2 N20
121VU EIS/GPWS/115VAC 3WZ P07
121VU ENGINE/ENG2/FADEC B 4KS2 Q40
121VU ENGINE/ENG2/FIRE DET/LOOP A 7WD2 Q39
121VU ENGINE/ENG1/FIRE DET/LOOP B 8WD1 Q38
121VU HYDRAULIC/LGCIU/SYS2 2GA Q35
121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
121VU FLIGHT CONTROLS/FCDC2/SPLY 20CE2 Q20
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
121VU EIS/DMC3/SPLY 10WT3 Q09
121VU EIS/DMC2/SPLY 10WT2 Q08
121VU EIS/FWC2/SPLY 2WW Q07
121VU ENGINE/ENG1 AND 2/EVMU 1EV R44
121VU ENGINE/ENG1/FADEC B/AND EIU 1 4KS1 R41
121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
** On A/C 101-150 301-400 501-550
121VU COM NAV/CIDS/FWD ATTND/PNL 170RH Q14
** On A/C 101-150 501-550
121VU COM NAV/CIDS/PROG AND TST PNL 161RH M06
121VU COM NAV/CIDS/DIR 1 AND 2/NORM 151RH M05
** On A/C 301-350
121VU COM NAV/CIDS/PROG &/TST PNL 161RH M08
** On A/C 301-400
121VU COM NAV/CIDS/DIR NORM/2 156RH M07
121VU COM NAV/CIDS/DIR NORM/1 151RH M06
** On A/C 001-100 201-300 351-500 551-700
122VU AIR COND/TEMP CTL SYS 2/CHAN 53HH W22
A/115VAC
122VU AIR COND/TEMP CTL SYS 2/CHAN 55HH W21
A/28VDC

JST Page 3
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

PANEL DESIGNATION FIN LOCATION


122VU AIR COND/TEMP CTL SYS 1/CHAN 49HH X22
A/115VAC
122VU AIR COND/TEMP CTL SYS 1/CHAN 51HH X21
A/28VDC
122VU AIR COND/TEMP CTL SYS 2/CHAN 56HH Y21
REV. DATE : 01-Nov-2012

B/28VDC
122VU AIR COND/TEMP CTL SYS 2/CHAN 54HH Y20
B/115VAC
122VU AIR COND/TEMP CTL SYS 1/CHAN 50HH Y18
B/115VAC
** On A/C ALL
122VU ANTI ICE/WHC/2 5DG2 W13
122VU ANTI ICE/WHC/1 5DG1 X13
122VU AIR COND/CAB PRESS/CTL/2 2HL Y22
122VU AIR COND/AVNCS/VENT/MONG 3HQ Y17
** On A/C 101-150 301-350 501-550
122VU AIR COND/SDCU/CHAN2 12WQ T18
122VU AIR COND/ZONE TEMP 2HK V18
CTL/115VAC/SYS2
122VU AIR COND/ZONE TEMP 1HK V17
CTL/115VAC/SYS1
122VU AIR COND/PACK TEMP CTL 22HH Y20
SYS2/2/115VAC
122VU AIR COND/PACK TEMP CTL 2HH Y18
SYS2/1/115VAC
** On A/C 001-050 201-301 351-353 401-401 501-550
2000VU CABIN COMMUNICATION SYSTEMS PRAM 2RX E01
** On A/C 101-150 302-350 354-400 551-700
2000VU PRAM 2RX E01
** On A/C 001-150 201-300 401-500 551-700
2001VU VACUUM TOILET SYSTEM/VACUUM SYS 35MG A06
** On A/C 301-400
2001VU VACU TOIL SYS-VACU-SYS 35MG A06
** On A/C 501-550
2001VU VACU TOIL SYS-VACU-SYS 35MG A05

** On A/C ALL
B. Computer reset procedure

NOTE : This reset procedure is used when a computer does not operate correctly.

NOTE : The line maintenance personnel can use it a first time to avoid a computer replacement (a reset must
be done for the applicable computer as indicated in the Computer Reset Table).

JST Page 4
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
But, if there is more than one reset for each flight cycle for a given computer, it is necessary to do the
specific troubleshooting procedure for the applicable system.
If after a reset, the computer operates correctly, no more action is necessary.
(1) To do computer reset:
(a) Set the related normal cockpit control to OFF, or open the related circuit breaker as specified in
the reset procedure.
REV. DATE : 01-Nov-2012

(b) Wait 3 seconds if a normal cockpit control is used, or 5 seconds if a circuit breaker is used (unless
a different time is indicated).
(c) Set the related normal cockpit control to ON, or close the related circuit breaker.
(d) Wait 3 seconds for the end of the reset.
** On A/C 101-150 301-350 501-550
C. Air Conditioning
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


21 CAB PR SYS 1(2) FAULT CABIN For CPC 1:
PRESSURE - On panel 49VU, open the
CONTROLLER circuit breaker 1HL.
(CPC) 1(2) FOR CPC 2:
- On panel 122VU, open the
circuit breaker 2HL.
After five seconds, close the
circuit breaker.
21 COND ZONE REGUL FAULT ZONE On panel 122VU:
TEMPERATURE - Open the circuit breaker 1HK.
CONTROLLER - Open the circuit breaker 2HK.
After five seconds, close the
circuit breaker.
21 AIR FWD (AFT) CRG VENT CARGO On panel 49VU:
FAULT VENTILATION - Open the circuit breaker 31HN.
CONTROLLER After five seconds, close the
circuit breaker.
21 VENT AVNCS SYS FAULT AVIONICS On panel 122VU:
EQUIPMENT - Open the circuit breaker 3HQ.
VENTILATION After five seconds, close the
COMPUTER circuit breaker.
21 AIR PACK 1(2) REGUL FAULT PACK For the PC 1:
CONTROLLER - On panel 122VU, open
(PC) 1(2) then close the circuit breaker 2HH.
For the PC 2:
- On panel 122VU, open
then close the circuit breaker 22HH.
21 COND AFT CRG HEAT FAULT AFT CARGO On panel 49VU:
HEAT - Open the circuit breaker 31HN.
CONTROLLER - After five seconds, close the
circuit breaker.

JST Page 5
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
** On A/C 001-100 201-300 351-500 551-700
C. Air Conditioning
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


21 CAB PR SYS 1(2) FAULT CABIN For CPC 1:
REV. DATE : 01-Nov-2012

PRESSURE - On panel 49VU, open the


CONTROLLER circuit breaker 1HL.
(CPC) 1(2) FOR CPC 2:
- On panel 122VU, open the
circuit breaker 2HL.
After five seconds, close the
circuit breaker.
21 AIR FWD (AFT) CRG VENT CARGO On panel 49VU:
FAULT VENTILATION - Open the circuit breaker 31HN
CONTROLLER After five seconds, close the
circuit breaker.
21 VENT AVNCS SYS FAULT AVIONICS On panel 122VU:
EQUIPMENT - Open the circuit breaker 3HQ.
VENTILATION After five seconds, close the
COMPUTER circuit breaker.
21 AIR PACK 1(2) REGUL FAULT AIR COND For the ACSC 1:
SYSTEM - On panel 122VU, open
CONTROLLER the circuit breaker 49HH,
(ACSC) 1(2) circuit breaker 50HH
and circuit breaker 51HH.
- On panel 49VU, open
the circuit breaker 52HH.
Then close the circuit breakers.
For the ACSC2:
- On panel 122VU, open
the circuit breaker 53HH,
circuit breaker 54HH,
circuit breaker 55HH and
circuit breaker 56HH.
Then close the circuit breakers.
21 COND AFT CRG HEAT FAULT AFT CARGO On panel 49VU:
HEAT - Open the circuit breaker 31HN.
CONTROLLER - After five seconds, close
the circuit breaker.

JST Page 6
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
** On A/C ALL
D. Auto Flight
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


22 AUTO FLT YAW DAMPER 1(2) FAC1(2) Open these C/Bs with the
REV. DATE : 01-Nov-2012

FAULT Yellow and Green hydraulic


systems pressurized:
- for the FAC 1: on the
panel 49VU, C/B 5CC1
- for the FAC 2: on the
panel 121VU, C/B 5CC2
Then close the C/Bs after 10
seconds.
22 WINDSHEAR DET FAULT or FAC 1+2 Open then close the C/Bs in
REAC W/S DET FAULT this the order:
- on the panel 49VU, C/B
5CC1 and C/B 14CC1
- on the panel 121VU, C/B
5CC2 and C/B 14CC2.

JST Page 7
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


22 AUTO FLT FCU 1(2) FAULT FCU For the FCU1:
- on the panel 49VU, open
the C/B 9CA1.
For the FCU2:
- on the panel 121VU, open
the C/B 9CA2.
REV. DATE : 01-Nov-2012

Close the C/B after 5


seconds.
If the fault does not
continue, do a check of the
target and barometer
references shown, and
correct them if necessary
(reset successful).
If the fault continues, open
again the two C/Bs 9CA1
on 49VU and 9CA2 on 121VU.
Close the C/Bs after 7 min,
with an interval less than
5 sec between side 1 and
side 2.
At least 30 sec are necessary
until the end of the FCU1
and FCU2 safety test.
If the fault does not
continue, do a check of the
target and barometer
references shown, and
correct them if necessary
(reset successful)
If the fault continues, end
of procedure (reset
unsuccessful).
22 One MCDU locked or blank MCDU Open then close the C/B of
Both MCDUs locked or blank FMGC the defective MCDU after 10
seconds:
- For the MCDU1: on the
panel 121VU or panel 49VU,
C/B 11CA1.
- For the MCDU2: on the
panel 121VU, C/B 11CA2.
- For the MCDU3: on the
panel 121VU, C/B 11CA3.

JST Page 8
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


22 FMGC malfunction FMGC On the panel 121VU or 49VU:
- open the FMGC 1 C/B 10CA1
and close it after 10
seconds.
If there is no reset of the
FMGC 1, do a reset of the
REV. DATE : 01-Nov-2012

FMGC 2 on the panel 121VU:


- open the C/B 10CA2 and
close it after 10 seconds.

** On A/C 101-150 301-350 501-550


E. Communications
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


23 COM CIDS 1+2 FAULT CIDS - Open the C/Bs in this
order:
on the panel 49VU, C/B 150RH
on the panel 121VU, C/B
151RH
- After 10 seconds, close
the C/Bs in this order:
151RH, 150RH.
23 Uncommanded EVAC horn CIDS Press the EVAC/HORN SHUT
actuation OFF switch.
If unsuccessful:
- Open the C/Bs in this
order:
on the panel 49VU, C/B 150RH
on the panel 121VU, C/B
151RH
- After 10 seconds, close
the C/Bs in this order:
151RH, 150RH.
23 Frozen RMP RMP You must do a reset of all
the RMPs, one after the
other.
On the RMP control panel:
- set the ON/OFF switch to
OFF
- after 5 seconds, set the
ON/OFF switch to ON.

JST Page 9
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


23 Frozen FAP Tape On the panel 121VU, open
reproducer the FAP C/B 170RH.
- After 10 seconds, close
the C/B 170RH.
If unsuccessful:
on the panel 2000VU
REV. DATE : 01-Nov-2012

- open the tape reproducer


/PRAM C/B 2RX.
After 10 seconds, close the
C/B.

** On A/C 351-400
E. Communications
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


23 COM CIDS 1+2 FAULT CIDS - Open the C/Bs in this
order:
on the panel 49VU, C/B 150RH
on the panel 121VU, C/B
151RH
- After 10 seconds, close
the C/Bs in this order:
151RH, 150RH.
23 Uncommanded EVAC horn CIDS Press the EVAC/HORN SHUT
actuation OFF switch.
If unsuccessful:
- Open the C/Bs in this
order:
on the panel 49VU, C/B 150RH
on the panel 121VU, C/B
151RH
- After 10 seconds, close
the C/Bs in this order:
151RH, 150RH.
23 Frozen RMP RMP You must do a reset of all
the RMPs, one after the
other.
On the RMP control panel:
- set the ON/OFF switch to
OFF
- after 5 seconds, set the
ON/OFF switch to ON.

JST Page 10
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


23 Frozen FAP Tape Open the C/Bs in this order:
reproducer On the panel 49VU, CB 171RH
On the panel 121VU, CB
170RH
- After 10 seconds, close
the C/Bs in this order:
REV. DATE : 01-Nov-2012

170RH, 171RH
If unsuccessful:
on the panel 2000VU
- open the tape reproducer
/PRAM C/B 2RX.
After 10 seconds, close the
C/B.

** On A/C 001-100 201-300 401-500 551-700


E. Communications
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


23 COM CIDS 1+2 FAULT CIDS - Open the C/Bs in this
order:
on the panel 49VU, C/B 150RH
on the panel 121VU, C/B
151RH
on the panel 49VU, C/B 157RH
on the panel 121VU, C/B
156RH
- After 10 seconds, close
the C/Bs in this order:
156RH, 157RH, 151RH and
150RH.
23 Uncommanded EVAC horn CIDS Press the EVAC/HORN SHUT
actuation OFF switch.
If unsuccessful:
- Open the C/Bs in this
order:
on the panel 49VU, C/B 150RH
on the panel 121VU, C/B
151RH
on the panel 49VU, C/B 157RH
on the panel 121VU, C/B
156RH
- After 10 seconds, close
the C/Bs in this order:
156RH, 157RH, 151RH and
150RH.

JST Page 11
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


23 Frozen RMP RMP You must do a reset of all
the RMPs, one after the
other.
On the RMP control panel:
- set the ON/OFF switch to
OFF
REV. DATE : 01-Nov-2012

- after 5 seconds, set the


ON/OFF switch to ON.
23 Frozen FAP FAP Open the C/Bs in this order:
On the panel 49VU, CB 171RH
On the panel 121VU, CB
170RH
- After 10 seconds, close
the C/Bs in this order:
170RH, 171RH
If unsuccessful:
on the panel 2000VU
- open the tape reproducer
/PRAM C/B 2RX.
After 10 seconds, close the
C/B.

** On A/C ALL
F. Electrical Power
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


24 GPU cannot be connected GAPCU If at least one power source
to the aircraft (IDG 1 or IDG 2, APU GEN or
batteries) is connected to
the electrical network of
the aircraft:
- On the ELEC control panel
35VU:
. Push and release the
EXT PWR pushbutton
switch.
If no power source is
connected to the electrical
network of the aircraft:
- On the ELEC control panel
35VU:
. Push the BAT 1 and BAT 2
pushbutton switches
(the OFF legend goes
off).

JST Page 12
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
** On A/C 101-150 301-350 501-550
G. Fire Protection
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


26 SMOKE LAV + CRG DET FAULT SDCU On the panel 49VU:
REV. DATE : 01-Nov-2012

- open the C/B 11WQ


On the panel 122VU:
- open the C/B 12WQ
After 10 seconds, close the
two C/B’s.
26 ENG1(2) LOOP k FAULT ENGINE FDU On the panel 49VU:
- For ENG1 FDU, open the
C/B 7WD1.
- For ENG2 FDU, open the
C/B 8WD2.
On the panel 121VU:
- For ENG1 FDU, open the
C/B 8WD1.
- For ENG2 FDU, open the
C/B 7WD2.
- After 5 seconds, close
the C/Bs.
26 APU FIRE LOOP k FAULT APU FDU On the panel 121VU:
- Open the C/Bs 2WG and 1WG.
- After 5 seconds, close the
C/Bs.

** On A/C ALL
H. Flight Controls
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


27 F/CTL ELAC 1(2) FAULT ELAC Reset the defective ELAC:
F/CTL ALTN LAW FAULT - Make sure that the
hydraulic systems are
depressurized before the
reset.
- Set the ELAC pushbutton
switch to OFF, then to ON.

JST Page 13
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


27 ELAC or SEC malfunction ELAC or SEC Reset the defective ELAC:
- Make sure that the
hydraulic systems are
depressurized before the
reset.
Open, then close the C/B of
REV. DATE : 01-Nov-2012

the defective ELAC or SEC.


For the ELAC 1(2):
- On the panel 49VU, C/B
15CE1.
- On the panel 121VU, C/B
15CE2.
For the SEC 1(2)(3):
- On the panel 49VU, C/B
21CE1.
- On the panel 121VU, C/B
21CE2 or 21CE3.
27 E/W FCDC1(2) FAULT FCDC On the panel 49VU:
- For FCDC1, open the C/B
20CE1.
- For FCDC2, open the C/B
20CE2.
- After 5 seconds, close
the C/Bs.

J. Fuel
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


28 Loss of fuel quantity FQIC On the overhead circuit
indication or, breaker panel 49VU:
Simultaneous triggering - Open the C/B 1QT.
of FUEL L XFR VALVE On the rear circuit
CLOSED and FUEL R XFR breaker panel 121VU:
VALVE CLOSED, although - Open the C/B 2QT.
FUEL SD indicates no After 5 seconds, close the
anomaly. two C/B’s.

K. Ice and Rain Protection


(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


30 ANTI ICE WHC Open then close the C/B of
L(R)/WINSHIELD (WINDOW) the defective WHC.
For the WHC1:
- on the panel 122VU, C/B
5DG1.
For the WHC2:
- on the panel 122VU, C/B
5DG2.

JST Page 14
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
L. Indicating/Recording Systems
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


31 FWS FWC 1(2) FAULT FWC Open then close the C/B of
the defective FWC
For the FWC1:
REV. DATE : 01-Nov-2012

- on the panel 49VU, C/B 3WW


For the FWC2:
- on the panel 121VU, C/B
2WW.
31 EIS DMC 1(2)(3) FAULT DMC Open then close the
circuit breaker of
the defective DMC
For the DMC1:
- on the overhead C/B panel
49VU, the circuit breaker
10WT1.
For the DMC2:
- on the rear C/B panel
121VU, the circuit breaker
10WT2.
For the DMC3:
- on the rear C/B panel
121VU, the circuit breaker
10WT3.
31 CAPT PFD DU malfunction CAPT PFD DU On the CAPT lightning/loud
speaker control-panel 301VU,
turn the PFD potentiometer
from the BRT position to
the OFF position.
- Wait for more than five
seconds.
On the CAPT lightning/loud
speaker control-panel 301VU,
turn the PFD potentiometer
from the OFF position to
the BRT position.
31 CAPT ND DU malfunction CAPT ND DU On the CAPT lightning/loud
speaker control-panel 301VU,
turn the ND potentiometer
from the BRT position to
the OFF position.
- Wait for more than five
seconds.
On the CAPT lightning/loud
speaker control-panel 301VU,
turn the ND potentiometer
from the OFF position to
the BRT position.

JST Page 15
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


31 F/O PFD DU malfunction F/O PFD DU On the F/O lightning/loud
speaker control-panel 500VU,
turn the PFD potentiometer
from the BRT position to
the OFF position.
- Wait for more than five
REV. DATE : 01-Nov-2012

seconds.
On the F/O lightning/loud
speaker control-panel 500VU,
turn the PFD potentiometer
from the OFF position to
the BRT position.
31 F/O ND DU malfunction F/O ND DU On the F/O lightning/loud
speaker control-panel 500VU,
turn the ND potentiometer
from the BRT position to
the OFF position.
- Wait for more than five
seconds.
On the F/O lightning/loud
speaker control-panel 500VU,
turn the ND potentiometer
from the OFF position to
the BRT position.
31 EWD malfunction EWD On the ECAM control panel
turn the UPPER DISPLAY
potentiometer from the
BRT + position to the OFF
position.
- Wait for more than five
seconds.
On the ECAM control panel
turn the UPPER DISPLAY
potentiometer from the
OFF position to the BRT +
position.
31 SD malfunction SD On the ECAM control panel
turn the LOWER DISPLAY
potentiometer from the
BRT position to the OFF
position.
- Wait for more than five
seconds.
On the ECAM control panel
turn the LOWER DISPLAY
potentiometer from the
OFF position to the BRT
position.

JST Page 16
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
M. Landing Gear
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


32 Braking malfunction BSCU On the panel 121VU:
- open the C/Bs 1GG, 2GG,
3GG and 4GG
REV. DATE : 01-Nov-2012

- after 5 seconds, close


the CB’s
32 L/G LGCIU 1(2) FAULT LGCIU 1(2) For the LGCIU 1:
- on the panel 121VU, open
the C/B 52GA then on 49VU,
C/B 1GA. Then close the
C/B 1GA and C/B 52GA
For the LGCIU 2:
- on the panel 121VU, open
then close the C/B 2GA.

N. Navigation
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


34 NAV MMR 1(2) FAULT MMR1(2) For the MMR 1:
- On the panel 49VU, open
the C/B 42RT1.
- After 5 seconds, close the
C/B.
For the MMR 2:
- On the panel 121VU, open
the C/B 42RT2.
- After 5 seconds, close the
C/B.
34 NAV TCAS FAULT TCAS On the panel 121VU:
- Open the C/B 4SG.
- After 5 seconds, close
the C/B.
34 NAV GPWS FAULT GPWC On the panel 121VU:
NAV GPWS TERR DET FAULT - Open the C/B 3WZ.
- After 5 seconds, close
the C/B.
34 NAV GPS 1(2) FAULT GPSSU On the panel 121VU:
- For GPSSU1, open the C/B
2SN1.
- For GPSSU2, open the C/B
2SN2.
- After 5 seconds, close
the C/Bs.

JST Page 17
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


34 NAV RA 1(2) FAULT XCVR-RA On the panel 121VU:
- For XCVR-RA 1, open the
C/B 1SA1.
- For XCVR-RA 2, open the
C/B 1SA2.
- After 5 seconds, close
REV. DATE : 01-Nov-2012

the C/Bs.

** On A/C 101-150 301-350 501-550


P. Water/Waste
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


38 Fault messages on the Vacuum On the panel 2001VU:
FAP in the cabin System - open the C/B 35MG
Controller - after 30 seconds, close
the C/B.

** On A/C 001-150 201-300 351-700


Q. Information Systems
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


46 ATSU malfunction ATSU On the rear circuit
breaker panel 121VU:
- Open the C/Bs in this
order: 3TX1 and 5TX1.
- After 5 seconds, close
the C/Bs in this order:
5TX1 and 3TX1.

** On A/C ALL
R. Engine
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


70 ENG IGN A+B FAULT FADEC and On the panels 49VU and 121VU
EIU open then close the C/B of
70 ENG 1(2) FADEC A(B) FAULT FADEC - For the FADEC 1, C/Bs
2KS1 and 4KS1.
- For the FADEC 2, C/Bs
2KS2 and 4KS2.

JST Page 18
24-00-00 PB201 Nov 01/12
Revision n˚: 34
@A318/A319/A320/A321
TROUBLE SHOOTING MANUAL
S. Engine Indicating
(1) Computer Reset Table

ATA SYSTEM MALFUNCTION COMPUTER RESET PROCEDURE


77 Loss of N1VIB and N2VIB EVMU On the panel 121VU:
indications for ENG1(2) - Open the C/B 2EV.
in ECAM SD - After 5 seconds, close the
REV. DATE : 01-Nov-2012

C/B.

JST Page 19
24-00-00 PB201 Nov 01/12
Revision n˚: 34

You might also like