Professional Documents
Culture Documents
N
G
USER MANUAL
Start
Displays
Menu navigation buttons
Access to the system menu
Operationg menu
User
Enroll
Delete
Amend
Set temp ID
CONTENTS
Setting
Basic Time, Data, Language, Volume, Background Image
Advanced Verification Mode, ID Mask, Use Tamer Alarm
Use Touch Sensor, Calibrate Sensor, Lumidigm Spoof, Restore Factory
AC Setting▶ Define Timezone, User Timezone, Lock Type(NC,NO), Lock Door,Release Time,
Door Open Warning, Instrsion Detection Sensor Mode, Reaccess Count,
Reaccess Limit Time, Wiegand Format, Anti-Passback, Setting Reader Of Outer Fingerprint
Communication▶Device ID, Baud Rate, TCP/IP Settings, Setting Wireless LAN,
Managing Computer IP Address, Communication Password
Schedule▶ Set Tmode, Ring Settings, Auto Door, Auto Funckey, None-Relay Funckey,
Day Light, Holiday, Funckey Alram, CD2 Auto Funckey, Idle Settings
Log Setting▶ Management Log Warning, General Log Warning
3.USB MEMORY
Dounload General Log/ Download All General Log/ Download Management Log/
Download All Management Log/ Download User Info/ Upload User Info/ Upgrade Firmware
4.SYSTEM INFO
Memory▶ User, Fingerprint, ID Card, General Log, Management Log, Number of photo
Device Info▶ Release Date, Serial Number, Manufacturer, Product Name,
Product Type, Engine Version, Firmware Version
Advanced▶ View General Log, View Management Log, View User Info
5.TEST
Test All/ Test Memory/ Test LCD/ Test Sound(AUTO)/ Test Sound(MANUAL)/ Test Sensor/ Test RTC/
Test cast status/ Test Card Reader
Cautions
Before using this device, read and follow all instructions for safety.
CPU ARM926E_21bit
USB 2 EA
125Khz (EM/HID/Prox)
RF Card
13.56Mhz (Mi fare/I-calss SE/ Felice)
KJ-3500 Bracket
Wiring harness by the
'wiring manual' to see it.
KJ-3500
CAMER
Face capture
LED
Product statu.
Fingerprint Sensor
Color TFT LCD User registration,
Displays time, authentication,
device status, On the fingerprint input
user list and UI Be used.
for operation
Card Sensor
Is used for user
authentication.
Connector
LAN CON12 CON2
Cable for connection to
CON1 CON4 CON13
Connector.
Dimensions
W:143mm W:143mm
H:143mm H:143mm
Side View
Fingerprint registration
Place the finger on the sensor as seen in below in the proper way. Place the entire area of your finger firmly to the sensor.
Proper way
CD ID FP
CD&FD ID&FD
ID&CD OPEN
ID&CD&FD CLOSE
KJ-3500 supports various type of access mode : Combination of Fingerprint, Card and ID(PIN)
Functions key
Function Key is usually used for Time & Attendance.
The admin is able to setup a certain definition to a function key in the program
(F1 = Sing in) The admin is able to find out the users attendance records.
1. Press Function Key (F1~F4) only or Press numbers after Function Key .
1. Press Function Key (F1~F4) only or press numbers after Function Key .
1. Press Function Key (F1~F4) only or Press numbers after Function Key .
Function key
Function key
Function key
Function key
1. Touch right down menu icon in the desktop 7. Push next button, enroll fingerprint, card photo
2. Input manager password ( initial secret # 1234 ) 8. When light come to sensor, input 3 times of fingerprint.
3. Click user icon 9. After select card enroll, touch card automatically
read card value
4. Click registration icon
10. After select photo enroll, shooting
5. Designation of number, input name & setting rights
11. After finishing all enrollment, push complete
6. Rights can be selected among user and manager button and return.
USer>delete
Same as registration process, it is able to delete 1st fingerprint, 2nd fingerprint and card in each,
If wish to delete all 3data, select ‘Delete All’ and corresponding ID is deleted
1. After entry of system manu > user and manager > delete
1. After entry system menu > setting temporarily ID > input user info.
4. Setting temporarily ID
1.Time
Set-up the time of the device. Device’s time is applied to the time of the event.
so it is important the accurate time
2.Date
Setup the date of the device
3.Language (Korean/English/Chinese)
Choose the language
4.volume
It can be adjust volume 0 ~ 10 from device.
5.Background image
It can be set background image
Setting>advanced 1
1.camera setting
Photo setting▶ No display : no shoot when confirmation
Now photo : shooting whenever authentication
Registered photo : indication photo when enroll
3.ID mask
When the user input ID, it hides user ID as xxxxxx and enhance the security.
5.Calibrate Sensor
Optical sensor perceive surroundings and optimize the brightness.
When use this function, it has to block extraneous light
1.Define Timezone
Able to set-up 256 timezones. refer to software (Guardian) manual 7.3 time zone set-up
2.User Timezone
Able to allocate 2 time zone for each user. 0 for [ All Time ] and 257 for [ None Time ]
7. Reaccess Count
No, 0~ 9 Limit reaccess count between no, 0 ~ 9times
10.Anti-Passback : No / Yes
Anti-passback activates through external wiegand input.
If there is two controllers for enter and exit, re-enter is allowed only it has exit event data
(EX : Public Parking lot, Restricted Area, Membership center )
1.Device ID (1 ~ 999)
Setting ID of device
It can be setting range 1 ~ 999, when making network through connecting computer and controller.
Each controller have to own their own address. This is function of changing or giving address of inherent.
[Each product of connecting to network, have to set each different value of address]
To connect device with software (Guardian) by TCP/IP ( LAN), it must set-up IP Address,
Subnet Mask, Gateway, (All the above data is for reference only and an confirm the details in
network environment of the PC to connect)
6.Communication Password
If the communication password is not correct, it is impossible to communicate with the software
Setting>Schedule 1
This page setting function, this function is used by guardian program.
It is possible to set the device itself.
1.Set Tmode
Setup the door mode and it is converted automatically according to the time and schedule.
Refer to software (Guardian) manual 7-4 controller
Special function/ Door mode how to setup the door mode
2.Ring Settings
Setup the bell ring schedule.
Refer to Software (Guardian) manual 7-4 controller special function / Bell Time how to setup the bell rings
3.Auto Door
Setup the operation time of the automatic door
refer to software (Guardian) manual 7-4 controller
Special function Auto Door how to setup the auto door.
※ Please refer setting way of controller/ special function / setting off day
Setting>Schedule 2
4.Auto Funckey
At the designated date and time, the corresponding key is set-up as default.
Refer to Software (Guardian) manual 7-4 controller
Special function auto F-Key how to setup the auto F-Key.
5.None-Relay Funckey
Setup none-relay Funckey and buzzer alarm key. Refer to Software (Guardian) manual
7-4 controller Special function No act F-Key how to setup the No Act F-key.
6.Day Light
Setup the daylight.
Refer to Software (Guardian) manual 7-4 controller
Special function Daylight how to setup Daylight.
7.Holiday
Holiday settings must comply with the day of the week
Refer to Software (Guardian) manual 7-4 controller Holiday setup
8.Funckey Alarm
Once input the alarm key and succeed to identify, it activates buzzer alarm or relay alarm.
10.Idle Settings
LCD power cut off : 0 ~ 60minutes
IDLE mode : 0 ~ 60minutes
Setting>Log settings
3.ID Card
ID Card numbers which is enrolled in the device
4.General Log
General log(access event) numbers
System info>Device info
Device info is set from the manufacturer and the user cannot edit this info
4.Product Name
Displays the device name.
System info>Advanced
Model
S/N