Professional Documents
Culture Documents
SECTION OVERVIEW
REVISION STATUS
1 GENERAL 02 11.12.02
2 SERVICE CODE (SC) 02 11.12.02
3 PIPING CLASS SHEET (PCS) 02 29.11.02
4 ELEMENT DATA SHEETS (EDS) 01 11.12.02
5 VALVE SELECTION MANUAL (VSM) 01 31.10.02
6 VALVE DATA SHEET (VDS) 01 15.11.02
7 VALVE SPECIFICATION KEY (VSK) 01 31.10.02
8 MATERIAL DATA SHEET (MDS) 02 11.12.02
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 1 14
SECTION 1
GENERAL
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 2 14
TABLE OF CONTENTS
SECTION 1
GENERAL
SECTION 2
SERVICE CODE (SC)
SECTION 3
PIPING CLASS SHEETS (PCS)
SECTION 4
ELEMENT DATA SHEETS (EDS)
SECTION 5
VALVE SELECTION MANUAL (VSM)
5.1 General
5.2 Selection Philosophy
5.3 Code Description
5.4 Valve Selection Notes
Table 5.1
SECTION 6
VALVE DATA SHEETS (VDS)
SECTION 7
VALVE SPECIFICATION KEY (VSK)
SECTION 8
MATERIAL DATA SHEETS (MDS)
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 3 14
1 GENERAL
1.1.1 Scope
This specification sets down the minimum requirements for piping and valves, which are to be used on existing
and new topside installations, risers, process and utility systems for the Ekofisk Field.
d) Flexible Hoses.
All piping components specified shall be in accordance with all applicable sections of the latest editions of the
following codes, standards, regulations and Company specifications.
This document is defined by the revision, which is given on the front page. The individual sheets in this
document will be revised separately with their own revision identity different from the front page.
To monitor which individual sheet revision is part of the overall revision (front-page revision) the following
system is applied and maintained:
By this means the individual sections and sheets are revised individually, and at the same time maintaining the
overall revision status. This enables sections and sheets to be used individually within the full document.
Projects shall use the opportunity to select relevant data sheets only, for a particular purpose, e.g. for
mechanical packages.
1.2.2 Content/Index
The revision status including the "Section Overview" also serves as an index. The content is compiled in the
same sequence as the revision status listing.
1 General
2 SC - Service Code
The revision status in front of each section lists the content in alphabetical order.
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 5 14
This specification will be updated to cover additional requirements, rectify inaccuracies/omissions and add
working notes as considered necessary to simplify interpretation of the document.
It will NOT be modified to incorporate particular deviations from the specification proposed by any
vendor/supplier/manufacturer. All such deviations shall be recorded as concession requests and
processed according to an agreed procedure by the responsible Package Engineer.
BE Bevel End
BOE Bevel One End
BW Butt Weld
FB Full Bore
FF Flat Face (Valves, Flanges) Full Face (Gaskets)
galv Galvanised
GRE Glassfibre Reinforced Epoxy
GRVE Glassfibre Reinforced Vinylester
LR Long Radius elbow
NGS Nordic Group of Steel Regulations
PE Plain End
RB Reduced Bore
Re Yield stress
RF Raised Face
Rm Ultimate tensile stress
RTJ Ring Type Joint
SCD Screwed
smls Seamless
SW Socket Weld
T&C Threaded and Coupled
TE Threaded End
TOE Threaded One End
TBE Threaded Both Ends
WN Welding Neck
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 6 14
1.4.1 General
This chapter gives a short introduction to the data sheets in the different sections.
Note that the EDS's and VSK's are each intended for dedicated types of specifications as described below.
Deviations exist however, and specified requirements expected to be found in one type of data sheet may be
listed in another type.
These data sheets briefly list the services, which the different piping classes are intended for. The identification
of the data sheet is by the prefix "E" for Ekofisk.
The services listed are general. The intention is that it should be used for selection of piping classes. The
services listed are not "all inclusive" which means that the piping class may be used for other services.
Detailed project services are listed in section 1.5 Service Class Summary.
These sheets are the main data sheets, which refers to all specifications required for the piping and valve
components. The references are either national/international standards or additional requirements defined by
this standard.
5th character (when used) - this character is reserved for certain applications:
X, Y, Z = Special applications
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 7 14
1st character - E for Ekofisk Standard Sheet or N for Norsok standard sheet
The valve selection manual provides a basic matrix of process and utility piping systems, with appropriate
service coding, against the preferred valve type required to achieve the following functions:
The valve selection manual shall be used for valve selection in the development of P&ID's.
BL = ball valve
BU = butterfly valve
CH = check valve
DM = diaphragm valve
GB = globe valve
GT = gate valve
NE = needle valve
PG = plug valve
SV = special valve
CB = double block & bleed valve
This is a data sheet, which lists the specification for the valve as an integral item (equipment assembled from
many single elements). Material specification for each single element is given in the VDS.
Title Doc.no. Operator Sec.no. ABB Offshore Systems
Piping and Valve Specification 5060 1 ConocoPhillips Norge
Project Rev.no. Rev.date Page: Of:
General 02 11.12.02 9 14
The VSK consists of a collection of numbered text units from a database. These numbers are the "TEXT ID" in
the left column in the VSK. Following the "TEXT ID" is the latest revision date for the text unit. The VSK itself
has its own revision number and date.
This data sheet lists specified material properties and special requirements.
The MDS's are referred to from the PCS and VDS. More than one material standard may be listed in the MDS.
In this case the standard referenced in the column "MATERIAL NAME" in the PCS and "MATERIAL" in the
VDS shall be selected.
For listed material without MDS reference Standard material shall be used.
C = Carbon steel
D = Duplex stainless steel
G = Galvanised Carbon steel
N = Nickel Alloys
P = Plastic and glass fibre reinforced plastic pipes (GRP)
R = 6Mo stainless steel
S = Stainless steel (type AISI 316)
T = Titanium
V = Alloy steels, low temperature grades ( f.ex. 3.5 Ni Steels)
X = Alloy steels
Z = Hardfacing and overlay welding
This table lists the extreme process design conditions found in each service. The set of process design parameters does not
represent any actual line. For actual line conditions, ref. the actual Line List.