You are on page 1of 2

Nitomortar FC* constructive solutions

High strength trowel grade, epoxy resin fairing coat,


repair mortar, bedding and adhesive

Uses Properties

Nitomortar FC is designed for application to minor Solids by weight : 100%


imperfections in concrete surfaces. It is suitable for Compressive strength: 70 N/mm2 @ 7 days
application from a feather-edge to 3 mm, and can be used in Pot life : 4 hours @ 25ºC
the following situations : 11/2 hours @ 35ºC
Drying time : 10 hours @ 25ºC
! Filling pinholes prior to overcoating with Nitocote*† or
4 hours @ 35ºC
Nitoflor*† products.
Overcoating time : After 24 hour curing period
! General reprofiling over large areas, up to 3 mm depth. Colour : Grey
Chemical resistance : Resistant to oils, fats, petrol,
! Sealing of surface cracks in preparation for crack injection.
salt and sugar solution, bleach,
! General purpose bedding mortar and adhesive dilute mineral acids, alkalis and
various solvents
Advantages
Instructions for use
! Cost effective - reduces usage of subsequent coatings
Preparation
! High performance - excellent chemical resistance, strong
adhesion to concrete substrate Concrete surfaces should be clean, dry and free from laitance.
Sandblasting or mechanical wire brushing may be necessary.
! User friendly - easy to apply and finish, manufactured to
meet local conditions Mixing

Care should be taken to ensure that Nitomortar FC is


Description
thoroughly mixed to produce a fully homogeneous paste.
Nitomortar FC is a two component thixotropic, solvent free,
The hardener' and 'base' components should be stirred
compound based on epoxy resins, graded fillers and
thoroughly in order to disperse any settlement before mixing
thixotropic agents. It is applied directly to concrete substrates,
them together. The entire contents of the 'hardener' should be
without primer, and cures to a surface ready for over coating.
emptied into the 'base' container and the components mixed
The base component is light grey coloured and the hardener
together using a Fosroc mixing paddle attached to a slow-
black to ease identification of uniform mixing.
speed (400/500rpm) heavy duty drill, until a uniform grey colour
and consistency is obtained. Mixing of 1kg packs can be
Design criteria
done by hand but care must be taken to ensure homogenus
Nitomortar FC is designed for filling pinholes and surface mixing. Under no circumstances should part packs be used,
irregularities in concrete prior to the application of subsequent or part mixing be attempted.
coatings. It can be applied from a feather-edge up to 3 mm
Application
thickness.
Due to the easy workability of the product, a variety of
For reprofiling, or hole filling, with thicknesses in excess of
instruments such as trowel, scraper, filling knife and
3 mm, it is recommended to use Nitomortar FC(B)*.
squeegee can be used. After mixing, material can be taken
directly from the can, or subdivided onto spot boards for
Technical support
individual applicators.
Fosroc offers a comprehensive technical support service to
Nitomortar FC can be overcoated with all epoxy coatings after
specifiers, end users and contractors. It is also able to offer
a minimum curing period of 24 hours. Prior to overcoating, the
on-site technical assistance, an AutoCAD facility and
surface of the fully cured Nitomortar FC should first be abraded
dedicated specification assistance in locations all over the
to assist adhesion, and then cleaned to a dust-free finish.
world.
Nitomortar FC*
Nitomortar FC*

Cleaning Precautions

Nitomortar FC should be removed from tools, equipment and Health and safety
mixers with Fosroc Solvent 102*† immediately after use.
Nitomortar FC and Fosroc Solvent 102 should not come in
Hardened material can only be removed mechanically.
contact with skin or eyes, or be swallowed. Ensure adequate
ventilation and avoid inhalation of vapours. Some people are
Estimating
sensitive to resins, hardeners and solvents. Wear suitable
Supply protective clothing, gloves and eye/face protection.
Nitomortar FC : 1.0 and 4.0 litre packs
If working in confined areas, suitable respiratory protective
Fosroc Solvent 102 : 5 and 25 litre cans
equipment must be used. The use of barrier creams provides
additional skin protection. Should accidental skin contact
Coverage and yield:
occur, remove immediately with a resin removing cream
Coverage of Nitomortar FC is wholly dependant upon surface followed by soap and water. Do not use solvent. In case of
conditions, site trials are therefore recommended to ascertain contact with eye, rinse immediately with plenty of clean water
actual usage on uneven substrates. As a guideline when and seek medical advice. If swallowed seek medical
applied at 200 microns dft coverage is approximately 5m2/litre. attention immediately - do not induce vomiting.

Fire
Storage
Nitomortar FC is non-flammable.
Shelf life
Fosroc Solvent 102 is flammable. Keep away from sources
12 months if kept in unopened tins and stored in a dry place
of ignition. No smoking. In the event of fire extinguish with
away from direct sunlight.
CO2 or foam. Do not use a water jet.
Storage conditions
Flash points
Store in dry conditions in the original, unopened containers. Fosroc Solvent 102 : 33ºC
If stored at high temperatures the shelf life may be reduced to
For further information, refer to the product materials safety
4 to 6 months.
data sheet.

Limitations
Additional information
- Do not mix part packs under any circumstances.
Fosroc manufactures a wide range of products specifically
- Nitomortar FC should not be exposed to moving water designed for the repair and refurbishment of damaged
during application. reinforced concrete. These include hand-placed and spray
grade repair mortars, fluid micro-concretes, chemical-
- Exposure to heavy rainfall prior to final set may result in
resistant epoxy mortars and a comprehensive package of
surface scour.
protective coatings.
- If any doubt arises concerning temperature or substrate
condition, consult the local Fosroc office.
* Denotes the trademark of Fosroc International Limited

See separate data sheet

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard
Conditions for the Supply of Goods and Service

Head Office
Al Gurg Fosroc telephone: (+9714) 2858606 fax: (+9714) 2859649 email: agf@fosroc.com
LLC Regional offices
Dubai, Al Gurg Fosroc telephone: 285 8787 fax: 285 2023 email: dubai@fosroc.com
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17735454 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com

www.fosroc.com
Oman, Al Amana telephone: 771 5080 fax: 771 7554 email: oman@fosroc.com
Qatar, Tadmur telephone: 413628 fax: 440812 email: qatar@fosroc.com

UAE/0201/04/E

You might also like