Professional Documents
Culture Documents
2006
Errorcodes Eks5
1012 Sensors Pressure sensor 1, piston Internal error of the sensor, measured values are not updated.
1013 Sensors Pressure sensor 1, piston The value is below the measuring range tolerance
1014 Sensors Pressure sensor 1, piston The allowable maximum value has been exceeded.
1017 Sensors Pressure sensor 1, piston The allowable difference to has been exceeded
1018 Sensors Pressure sensor 1, piston The sensor was manually switched off with keypad inputs at the
central unit.
1019 Sensors Pressure sensor 1, piston Undefined, basic function indicates error
1022 Sensors pressure sensor 2, piston Internal sensor error, measured values are not updated.
1023 Sensors pressure sensor 2, piston The value is below the measuring range tolerance.
1024 Sensors pressure sensor 2, piston The allowable maximum value has been exceeded.
1027 Sensors pressure sensor 2, piston The allowable difference has been exceeded.
1028 Sensors pressure sensor 2, piston The pressure sensor was manually switched off with keypad
inputs at the central unit.
1029 Sensors pressure sensor 2, piston Undefined, basic function indicates error.
1032 Sensors pressure sensor , rod side (- Internal sensor error, measured values are not updated.
1033 Sensors pressure sensor , rod side (- The value is below the measuring range tolerance.
1034 Sensors pressure sensor , rod side (- The allowable maximum value has been exceeded.
1035 Sensors pressure sensor , rod side (- Sensor indicated internal error.
Page 1
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1038 Sensors pressure sensor , rod side (- The sensor was manually switched off with keypad inputs at the
central unit.
1039 Sensors pressure sensor , rod side (- Undefined, basic function indicates error
1042 Sensors Angle A mainboom (-A114) Internal error of Sensor, measured values are not updated.
1043 Sensors Angle A mainboom (-A114) The value is below the measuring range tolerance.
1044 Sensors Angle A mainboom (-A114) The allowable maximum value has been exceeded.
1045 Sensors Angle A mainboom (-A114) CAN - Bus transmitter board indicates internal error
1047 Sensors Angle A mainboom (-A114) The allowable difference has been exceeded.
1048 Sensors Angle A mainboom (-A114) The angle sensor was manually switched off with keypad inputs at
the central unit.
1049 Sensors Angle A mainboom (-A114) Undefined, basic function indicated error
1052 Sensors Angle B mainboom (-A111) Internal sensor error, measured values are not updated.
1053 Sensors Angle B mainboom (-A111) The value is below the measuring range tolerance.
1054 Sensors Angle B mainboom (-A111) The allowable maximum value has been exceeded.
1055 Sensors Angle B mainboom (-A111) CAN - Bus transmitter board indicates internal error
1057 Sensors Angle B mainboom (-A111) The allowable difference has been exceeded.
1058 Sensors Angle B mainboom (-A111) The sensor was manually switched off with keypad inputs at the
central unit.
1059 Sensors Angle B mainboom (-A111) Undefined, basic function indicated error
1062 Sensors length sensor A outside Internal sensor error, measured values are not updated.
Page 2
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1064 Sensors length sensor A outside The allowable maximum value has been exceeded.
1065 Sensors length sensor A outside CAN - Bus transmitter board indicates internal error
1067 Sensors length sensor A outside The allowable difference has been exceeded.
1068 Sensors length sensor A outside The sensor was manually switched off with keypad inputs at the
central unit.
1069 Sensors length sensor A outside Undefined, basic function indicated error
1072 Sensors length sensor B outside drum Internal sensor error, measured values are not updated.
1073 Sensors length sensor B outside drum The value is below the measuring range tolerance.
1074 Sensors length sensor B outside drum The allowable maximum value has been exceeded.
1075 Sensors length sensor B outside drum CAN - Bus transmitter board indicates internal error
1077 Sensors length sensor B outside drum The allowable difference has been exceeded.
1078 Sensors length sensor B outside drum The sensor was manually switched off with keypad inputs at the
central unit.
1079 Sensors length sensor B outside drum Undefined, basic function indicated error
1082 Sensors length sensor A inside drum Internal sensor error, measured values are not updated.
1083 Sensors length sensor A inside drum The value is below the measuring range tolerance.
1084 Sensors length sensor A inside drum The allowable maximum value has been exceeded.
1085 Sensors length sensor A inside drum CAN - Bus transmitter board indicates internal error
1087 Sensors length sensor A inside drum The allowable difference has been exceeded.
Page 3
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1089 Sensors length sensor A inside drum Undefined, basic function indicated error
1092 Sensors length sensor B inside drum Internal sensor error, measured values are not updated.
1093 Sensors length sensor B inside drum The value is below the measuring range tolerance.
1094 Sensors length sensor B inside drum The allowable maximum value has been exceeded.
1095 Sensors length sensor B inside drum CAN - Bus transmitter board indicates internal error
1097 Sensors length sensor B inside drum The allowable difference has been exceeded.
1098 Sensors length sensor B inside drum The sensor was manually switched off with keypad inputs at the
central unit.
1099 Sensors length sensor B inside drum Undefined, basic function indicated error
1102 Sensors slewing angle A (-A3706) Internal sensor error, measured values are not updated.
1103 Sensors slewing angle A (-A3706) The value is below the measuring range tolerance.
1104 Sensors slewing angle A (-A3706) The allowable maximum value has been exceeded.
1105 Sensors slewing angle A (-A3706) CAN - Bus transmitter board indicates internal error
1107 Sensors slewing angle A (-A3706) The allowable difference has been exceeded.
1108 Sensors slewing angle A (-A3706) The sensor was manually switched off with keypad inputs at the
central unit.
1109 Sensors slewing angle A (-A3706) Undefined, basic function indicated error
1112 Sensors slewing angle B (-A3706) Internal sensor error, measured values are not updated.
1113 Sensors slewing angle B (-A3706) The value is below the measuring range tolerance.
Page 4
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1115 Sensors slewing angle B (-A3706) CAN - Bus transmitter board indicates internal error
1117 Sensors slewing angle B (-A3706) The allowable difference has been exceeded.
1118 Sensors slewing angle B (-A3706) The sensor was manually switched off with keypad inputs at the
central unit.
1119 Sensors slewing angle B (-A3706) Undefined, basic function indicated error
1132 Sensors difference angle jib A (-A210 Internal sensor error, measured values are not updated.
1133 Sensors difference angle jib A (-A210 The value is below the measuring range tolerance.
1134 Sensors difference angle jib A (-A210 The allowable maximum value has been exceeded.
1135 Sensors difference angle jib A (-A210 CAN - Bus transmitter board indicates internal error
1137 Sensors difference angle jib A (-A210 The allowable difference has been exceeded.
1138 Sensors difference angle jib A (-A210 The sensor was manually switched off with keypad inputs at the
central unit.
1139 Sensors difference angle jib A (-A210 Undefined, basic function indicated error
1142 Sensors difference angle jib B (-A216) Internal error of CAN - Bus transmitter board, measured values are
not updated.
1143 Sensors difference angle jib B (-A216) Internal sensor error, measured values are not updated.
1144 Sensors difference angle jib B (-A216) The allowable maximum value has been exceeded.
1145 Sensors difference angle jib B (-A216) CAN - Bus transmitter board indicates internal error
1147 Sensors difference angle jib B (-A216) The allowable difference has been exceeded.
1148 Sensors difference angle jib B (-A216) The sensor was manually switched off with keypad inputs at the
central unit.
Page 5
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1152 Sensors angle steering (-A217) Internal error of CAN - Bus transmitter board, measured values are
not updated.
1153 Sensors angle steering (-A217) Internal sensor error, measured values are not updated.
1154 Sensors angle steering (-A217) The allowable maximum value has been exceeded.
1155 Sensors angle steering (-A217) CAN - Bus transmitter board indicates internal error
1158 Sensors angle steering (-A217) The sensor was manually switched off with keypad inputs at the
central unit.
1159 Sensors angle steering (-A217) Undefined, basic function indicated error
1162 Sensors Lenght sensor A Drum FAJ Internal sensor error, measured values are not updated.
1163 Sensors Lenght sensor A Drum FAJ The value is below the measuring range tolerance
1164 Sensors Lenght sensor A Drum FAJ The allowable maximum value has been exceeded.
1165 Sensors Lenght sensor A Drum FAJ Sensor indicated internal error.
1167 Sensors Lenght sensor A Drum FAJ The allowable difference to has been exceeded
1168 Sensors Lenght sensor A Drum FAJ The sensor was manually switched off with keypad inputs at the
central unit.
1169 Sensors Lenght sensor A Drum FAJ Undefined, basic function indicates error
1172 Sensors angle jib A (-A210 R1) Internal sensor error, measured values are not updated.
1173 Sensors angle jib A (-A210 R1) The value is below the measuring range tolerance.
1174 Sensors angle jib A (-A210 R1) The allowable maximum value has been exceeded.
1175 Sensors angle jib A (-A210 R1) CAN - Bus transmitter board indicates internal error
Page 6
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1177 Sensors angle jib A (-A210 R1) The allowable difference has been exceeded.
1178 Sensors angle jib A (-A210 R1) The sensor was manually switched off with keypad inputs at the
central unit.
1179 Sensors angle jib A (-A210 R1) Undefined, basic function indicated error
1182 Sensors angle jib B (-A210) Internal error of CAN - Bus transmitter board, measured values are
not updated.
1183 Sensors angle jib B (-A210) The value is below the measuring range tolerance.
1184 Sensors angle jib B (-A210) Internal sensor error, measured values are not updated.
1185 Sensors angle jib B (-A210) CAN - Bus transmitter board indicates internal error
1187 Sensors angle jib B (-A210) The allowable difference has been exceeded.
1188 Sensors angle jib B (-A210) The sensor was manually switched off with keypad inputs at the
central unit.
1189 Sensors angle jib B (-A210) Undefined, basic function indicated error
1192 Sensors force sensor A jib (-A213) Internal sensor error, measured values are not updated.
1193 Sensors force sensor A jib (-A213) The value is below the measuring range tolerance.
1194 Sensors force sensor A jib (-A213) The allowable maximum value has been exceeded.
1195 Sensors force sensor A jib (-A213) CAN - Bus transmitter board indicates internal error
1197 Sensors force sensor A jib (-A213) The allowable difference has been exceeded.
1198 Sensors force sensor A jib (-A213) The sensor was manually switched off with keypad inputs at the
central unit.
1199 Sensors force sensor A jib (-A213) Undefined, basic function indicated error
Page 7
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1203 Sensors force sensor B jib (-A213) The value is below the measuring range tolerance.
1204 Sensors force sensor B jib (-A213) The allowable maximum value has been exceeded.
1205 Sensors force sensor B jib (-A213) CAN - Bus transmitter board indicates internal error
1207 Sensors force sensor B jib (-A213) The allowable difference has been exceeded.
1208 Sensors force sensor B jib (-A213) The sensor was manually switched off with keypad inputs at the
central unit.
1209 Sensors force sensor B jib (-A213) Undefined, basic function indicated error
1212 Sensors Mobile auxiliary angle Internal sensor error, measured values are not updated.
1213 Sensors Mobile auxiliary angle The value is below the measuring range tolerance.
1214 Sensors Mobile auxiliary angle The allowable maximum value has been exceeded.
1215 Sensors Mobile auxiliary angle CAN - Bus transmitter board indicates internal error
1217 Sensors Mobile auxiliary angle The allowable difference has been exceeded.
1218 Sensors Mobile auxiliary angle The sensor was manually switched off with keypad inputs at the
central unit.
1219 Sensors Mobile auxiliary angle Undefined, basic function indicated error
1252 Sensors Load sensor A, Megalift left Internal sensor error, measured values are not updated.
1253 Sensors Load sensor A, Megalift left The value is below the measuring range tolerance.
1254 Sensors Load sensor A, Megalift left The allowable maximum value has been exceeded.
1255 Sensors Load sensor A, Megalift left CAN - Bus transmitter board indicates internal error
Page 8
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1258 Sensors Load sensor A, Megalift left The sensor was manually switched off with keypad inputs at the
central unit.
1259 Sensors Load sensor A, Megalift left Undefined, basic function indicated error
1262 Sensors Load sensor B, Megalift left Internal sensor error, measured values are not updated.
1263 Sensors Load sensor B, Megalift left The value is below the measuring range tolerance.
1264 Sensors Load sensor B, Megalift left The allowable maximum value has been exceeded.
1265 Sensors Load sensor B, Megalift left CAN - Bus transmitter board indicates internal error
1267 Sensors Load sensor B, Megalift left The allowable difference has been exceeded.
1268 Sensors Load sensor B, Megalift left The sensor was manually switched off with keypad inputs at the
central unit.
1269 Sensors Load sensor B, Megalift left Undefined, basic function indicated error
1272 Sensors Load sensor A, Megalift right Internal sensor error, measured values are not updated.
1273 Sensors Load sensor A, Megalift right The value is below the measuring range tolerance.
1274 Sensors Load sensor A, Megalift right The allowable maximum value has been exceeded.
1275 Sensors Load sensor A, Megalift right CAN - Bus transmitter board indicates internal error
1277 Sensors Load sensor A, Megalift right The allowable difference has been exceeded.
1278 Sensors Load sensor A, Megalift right The sensor was manually switched off with keypad inputs at the
central unit.
1279 Sensors Load sensor A, Megalift right Undefined, basic function indicated error
1282 Sensors Load sensor B, Megalift right Internal sensor error, measured values are not updated.
Page 9
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1284 Sensors Load sensor B, Megalift right The allowable maximum value has been exceeded.
1285 Sensors Load sensor B, Megalift right CAN - Bus transmitter board indicates internal error
1287 Sensors Load sensor B, Megalift right The allowable difference has been exceeded.
1288 Sensors Load sensor B, Megalift right The sensor was manually switched off with keypad inputs at the
central unit.
1289 Sensors Load sensor B, Megalift right Undefined, basic function indicated error
1341 Sensors Length potentiometer Control function of the length calculation of main boom causes an
error, due to the length comparison between length of the outside
1342 Sensors Length potentiometer ECOS The allowable difference between internal length drum and ECOS
precision length sensor values has been exceeded.
1351 Sensors Central unit CAN controller is in the "Bus off" state, the data transmission is
faulty.
1352 Sensors Central unit CAN controller is in the "receive warning" state, data transmission
is faulty.
1353 Sensors Central unit CAN controller is the "transmit warning" state, data transmission is
faulty.
1354 Sensors Central unit Internal data transmission is faulty, I/O - Bus.
1355 Sensors Central unit Incorrect CAN channel was selected, software.
1356 Sensors Central unit Intenal data transmission is faulty, I/O - error.
1361 Sensors Central unit CAN controller is in the "Bus off" state, data transmission is faulty.
1362 Sensors Central unit CAN controller is in the "receive warning" state, data transmission
is faulty.
1363 Sensors Central unit CAN controller is in the "transmit warning" state, data transmission
is faulty.
1364 Sensors Central unit Internal data transmission is faulty, I/O - Bus.
1365 Sensors Central unit Incorrect CAN channel was selected, software.
1366 Sensors Central unit Internal data transmission is faulty, I/O error.
1371 Sensors Central unit CAN controller is in the "Bus off" state, data transmission is faulty.
1372 Sensors Central unit CAN controller is in the "receive warning" state, data transmission
is faulty.
Page 10
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1374 Sensors Central unit CAN controller is in the "Bus off" state, data transmission is faulty.
1375 Sensors Central unit CAN controller is in the "receive warning" state, data transmission
is faulty.
1376 Sensors Central unit CAN controller is in the "transmit warning" state, data transmission
is faulty.
1381 Sensors Central unit CAN controller is in the "Bus off" state, data transmission is faulty.
1382 Sensors Central unit CAN controller is in the "receive warning" state, data transmission
is faulty.
1384 Sensors Central unit Internal data transmission is faulty, I/O - Bus.
1385 Sensors Central unit Incorrect CAN channel was selected, software.
1386 Sensors Central unit Internal data transmission is faulty, I/O error.
1391 Sensors Central unit CAN controller is in the "Bus off" state, the data transmission is
faulty.
1392 Sensors Central unit CAN controller is in the "receive warning" state, data transmission
is faulty.
1393 Sensors Central unit CAN controller is the "transmit warning" state, data transmission is
faulty.
1394 Sensors Central unit Internal data transmission is faulty, I/O - Bus.
1395 Sensors Central unit Incorrect CAN channel was selected, software.
1396 Sensors Central unit Intenal data transmission is faulty, I/O - error.
1502 Sensors Length sensor outrigger A FL Internal error of the sensor, measured values are not updated.
1503 Sensors Length sensor outrigger A FL The value is below the measuring range tolerance
1504 Sensors Length sensor outrigger A FL The allowable maximum value has been exceeded.
1505 Sensors Length sensor outrigger A FL CAN-IO Card indicated internal error.
1507 Sensors Length sensor outrigger A FL The allowable difference to has been exceeded
Page 11
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1509 Sensors Length sensor outrigger A FL Undefined, basic function indicates error
1512 Sensors Length sensor outrigger B FL Internal error of the sensor, measured values are not updated.
1513 Sensors Length sensor outrigger B FL The value is below the measuring range tolerance
1514 Sensors Length sensor outrigger B FL The allowable maximum value has been exceeded.
1515 Sensors Length sensor outrigger B FL CAN-IO Card indicated internal error.
1517 Sensors Length sensor outrigger B FL The allowable difference to has been exceeded
1518 Sensors Length sensor outrigger B FL The sensor was manually switched off.
1519 Sensors Length sensor outrigger B FL Undefined, basic function indicates error
1522 Sensors Length sensor outrigger A FR Internal error of the sensor, measured values are not updated.
1523 Sensors Length sensor outrigger A FR The value is below the measuring range tolerance
1524 Sensors Length sensor outrigger A FR The allowable maximum value has been exceeded.
1525 Sensors Length sensor outrigger A FR CAN-IO Card indicated internal error.
1527 Sensors Length sensor outrigger A FR The allowable difference to has been exceeded
1528 Sensors Length sensor outrigger A FR The sensor was manually switched off.
1529 Sensors Length sensor outrigger A FR Undefined, basic function indicates error
1532 Sensors Length sensor outrigger B FR Internal error of the sensor, measured values are not updated.
1533 Sensors Length sensor outrigger B FR The value is below the measuring range tolerance
Page 12
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1535 Sensors Length sensor outrigger B FR CAN-IO Card indicated internal error.
1537 Sensors Length sensor outrigger B FR The allowable difference to has been exceeded
1538 Sensors Length sensor outrigger B FR The sensor was manually switched off.
1539 Sensors Length sensor outrigger B FR Undefined, basic function indicates error
1542 Sensors Length sensor outrigger A RL Internal error of the sensor, measured values are not updated.
1543 Sensors Length sensor outrigger A RL The value is below the measuring range tolerance
1544 Sensors Length sensor outrigger A RL The allowable maximum value has been exceeded.
1545 Sensors Length sensor outrigger A RL CAN-IO Card indicated internal error.
1547 Sensors Length sensor outrigger A RL The allowable difference to has been exceeded
1548 Sensors Length sensor outrigger A RL The sensor was manually switched off.
1549 Sensors Length sensor outrigger A RL Undefined, basic function indicates error
1552 Sensors Length sensor outrigger B RL Internal error of the sensor, measured values are not updated.
1553 Sensors Length sensor outrigger B RL The value is below the measuring range tolerance
1554 Sensors Length sensor outrigger B RL The allowable maximum value has been exceeded.
1555 Sensors Length sensor outrigger B RL CAN-IO Card indicated internal error.
1557 Sensors Length sensor outrigger B RL The allowable difference to has been exceeded
1558 Sensors Length sensor outrigger B RL The sensor was manually switched off.
Page 13
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1562 Sensors Length sensor outrigger A RR Internal error of the sensor, measured values are not updated.
1563 Sensors Length sensor outrigger A RR The value is below the measuring range tolerance
1564 Sensors Length sensor outrigger A RR The allowable maximum value has been exceeded.
1565 Sensors Length sensor outrigger A RR CAN-IO Card indicated internal error.
1567 Sensors Length sensor outrigger A RR The allowable difference to has been exceeded
1568 Sensors Length sensor outrigger A RR The sensor was manually switched off.
1569 Sensors Length sensor outrigger A RR Undefined, basic function indicates error
1572 Sensors Length sensor outrigger B RR Internal error of the sensor, measured values are not updated.
1573 Sensors Length sensor outrigger B RR The value is below the measuring range tolerance
1574 Sensors Length sensor outrigger B RR The allowable maximum value has been exceeded.
1575 Sensors Length sensor outrigger B RR CAN-IO Card indicated internal error.
1577 Sensors Length sensor outrigger B RR The allowable difference to has been exceeded
1578 Sensors Length sensor outrigger B RR The sensor was manually switched off.
1579 Sensors Length sensor outrigger B RR Undefined, basic function indicates error
1602 Sensors Anglesensor arm Working Internal error of the sensor, measured values are not updated.
1603 Sensors Anglesensor arm Working The value is below the measuring range tolerance
1604 Sensors Anglesensor arm Working The allowable maximum value has been exceeded.
Page 14
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
1607 Sensors Anglesensor arm Working The allowable difference to has been exceeded
1608 Sensors Anglesensor arm Working The sensor was manually switched off.
1609 Sensors Anglesensor arm Working Undefined, basic function indicates error
2011 Multilevel inputs Recognition boom pins locked Central unit recognises open load.
2012 Multilevel inputs Recognition, boom pins Central unit recognises short to ground.
2013 Multilevel inputs Recognition, boom pins Central unit recognises short circuit to battery voltage.
2014 Multilevel inputs Recognition, boom pins Unstable signal to central unit.
2021 Multilevel inputs Recognition, tele cylinder left Central unit recognises open load.
2022 Multilevel inputs Recognition, tele cylinder left Central unit recognises short to ground.
2023 Multilevel inputs Recognition, tele cylinder left Central unit recognises short circuit to battery voltage.
2024 Multilevel inputs Recognition, tele cylinder left Unstable signal to central unit.
2025 Multilevel inputs Recognition, tele cylinder left Difference signal between X4,4 and X4,7
2031 Multilevel inputs Recognition SLI bypassed Central unit recognises open load.
2034 Multilevel inputs Recognition SLI bypassed Unstable signal to central unit..
Page 15
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
3014 Communication to Cut off Difference Cut Off Picture between Ecos and Lmb
3031 Communication Tele picture transmission The tele picture of ECOS is not updated.
3033 Communication Tele picture comparison ECOS and RCI have different tele pictures.
3042 Communication to Info Data transmission ESX 2 Data transmission of ESX 2 is faulty.
5027 Crane program Jib Load limit for derricking the swingaway lattice is exceeded. The
message is issued to inform the operator of the limitation, it does
5028 Crane program Jib Allowable tolerance between calculated and measured angle has
been exceeded .
Page 16
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
5066 Crane program Megalift max. load of the span cylinder is exceeded
6021 Hardware Fuse No. 1 Fuse No.1 defect or there is no supply voltage.
6022 Hardware Fuse No. 2 Fuse No. 2 defect or there is no supply voltage.
6023 Hardware Fuse No. 3 Fuse No. 3 defect or there is no supply voltage.
6024 Hardware Fuse No. 11 Fuse No. 11 defect or there is no supply voltage.
6025 Hardware Fuse No. 12 Fuse No. 12 defect or there is no supply voltage.
Page 17
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
6029 Hardware Supply time Internal components of the central unit are faulty.
6033 Hardware Supply voltage (5V) Internal 5V voltage of the central unit is faulty.
6041 Hardware Parameter memory 1 Internal components of the central unit are faulty.
6042 Hardware Parameter memory 1 Internal components of the central unit are faulty.
6043 Hardware Parameter memory 1 Internal components of the central unit are faulty.
6046 Hardware Parameter memory 1 Internal components of the central unit are faulty.
6049 Hardware Parameter memory 1 Internal components of the central unit are faulty.
6051 Hardware Parameter memory 2 Internal components of the central unit are faulty.
6053 Hardware Parameter memory 2 Internal components of the central unit are faulty.
6056 Hardware Parameter memory 2 Internal components of the central unit are faulty.
6059 Hardware Parameter memory 2 Internal components of the central unit are faulty.
6061 Hardware Memory test, external RAM Internal components of the central unit are faulty.
6069 Hardware Memory test, external RAM Internal components of the central unit are faulty.
6071 Hardware Function time Internal components of the central unit are faulty.
6072 Hardware Function time Internal components of the central unit are faulty.
6079 Hardware Supply time Internal components of the central unit are faulty.
Page 18
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
7023 Software Display The Display send the Crantype (Displaysoftware) - this to be
different to Crantype from the EKS - Software
8011 Operation Input of rigging / reeving code After entering the rigging/reeving code, the code is to be confirmed.
8033 slewing gear slewing gear brake slewing gear brake isn`t inserted
8121 Operation Crane type The incorrect crane type was quoted in the EE1 of the central unit .
8131 Operation Sensor calibration update Auto calibration is released. EE2 (address 17).
Page 19
Version 1.9 Datum: 14.02.2006
Errorcodes Eks5
8172 Operation Recognition Outrigger rigging code isn`t be compatible to Outtrigger recognition
Page 20