Professional Documents
Culture Documents
org - Reemplazo del firmware para reproductores "S1 mp3 player" - Tutorial de recuperación de aparatos "muertos"
● Principal
● Index
● Mapa del Web
● Documentación
Espec. Hardware
●
● Manuales
● Guías avanzadas
● Descargas
Firmware list
●
● Aplicaciones y Utilidades
● Desarrollo
● Tareas por hacer
● Available works
● Enlaces
● Página de Enlaces
We need developers for the SWAN project! Subscribe and post here if you can help!
Once you've found your board number, you may see if there is any tested firmware for your player at the
Firmware list.
If you don't know how to disassemble your mp3 player, read on.
2. Desmonte el s1mp3
(Written by Crunchy )
0) find a clear table / desk to work on, make sure the floor is not to messy. It'll be a LOT easier to find
back those tiny little screws / plastic buttons that tend to fall out exactly the wrong way
1) stick a screwdriver/knife/needle between the USB plug and the bottom plastic part (the one that holds
the battery) . Any gap large enough to fit a sharp edge in will do.
2) lever the bottom plastic of the rest of the player. It's not welded or glued tight, so it'll come of easily.
Be forceful, but gentle, if necessary. Don't worry if you hear plastic "snapping" it's just the clips coming
loose, you are not breaking anything.
3) in the four corners of the PCB (the printboard with all the chips) you'll find four screws, find a
screwdriver that fits, and unscrew them PUT THE SCREWS IN A CONTAINER! Anything will do,
from an egg holder to tupperware to an ashtray, JUST DON'T LOOSE THE SCREWS!!!! You can now
lift off the main PCB. Be carefull, as the LCD connector cable (brown flat cable) is quite fragile. Don't
break it!
4) You can now safely remove the chrome/silver/shiny ring from the player. Note how it fits UNDER
the main PCB, and how the LCD connector cable goes through it. This bit is a bit tricky to reassemble
later, so if you remember how everything was in the first place, It'll be easier to put it back together.
5) you can now see the back of the LCD board. there should be two screws in it. Again, take your
screwdriver and unscrew them. Put these screws in a (different) container! Again, Don't lose the screws!
you NEED them. Put them in a different container to make sure you don't mix them up with the four
"main PCB screws", as that will cause trouble when you put the player back together. After all that, you
can take the LCD board from the front of the case. Remember, the brown LCD connector cable is
FRAGILE, don't break it!
Congratulations, you have now disassembled your S1MP3 player! To reassemble it, just follow this
guide in reverse order.
well, I hope this little guide is of help to you, anyway, report back the results, even if it fails, even if it
succeeds, and why it worked/failed. It'll be education for all of us.
Unplug the player and remove all the drivers related to USB at the device manager
Now, click "SCAN FOR HARDWARE CHANGES" button. Finally after the new USB drivers are
installed, plug in your player.
If you have problems with drivers, they may be obtained at the place you've installed the MP3 player
utilities(program files/MP3 Player Utilities/) At folders "Windows98Drv", and "Dissipate/drivers".
If you follow all this steps and windows still can't recognize it, you may try to push ALL the buttons
while connecting it to the USB hub. Try every button, and keep the button hold. You may also try to
plug it on another computer.
If nothing works, don't get desperate, you can still try to short-circuit the memory chip to make it run the
"recovery mode".
Firstly, make sure you have done the previous steps, and disable any anti virus/anti spywares.
Try to plug your device with and without the batteries, and see if holding the buttons solves the update
program start errors.
If you are still getting errors like "UNKNOW FLASH TYPE ", "FLASH NOT RESPONDING",
"DEVICE NOT DETECTED", "DEVICE IS BUSY", You should uninstall you current updater
program and try other ones. (see the Herramienta de actualización del reproductor)
If you still can't make it work, you can try to short-circuit the memory chip to make it run the "recovery
mode".
You must disassemble your mp3 player. If you haven't done this yet, check the disassemble the s1mp3.
Recognize the memory chip, near the ATJ2085 chip. It's usually a samsung chip, and it's the biggest
silicon on the board. To help identifying the device components, check the Vista interna del s1Mp3. We
have seen players with 2 memory chips, too. If you have one of those, you have to short the memory
chip near the ATJ2085.
Now, without the batteries , with a flat screwdriver, touch any of the 8 IO legs of the memory chip.
Then, with the screwdriver on, connect the player to the USB.
If you are successful, windows will recognize an ADFU server device. Now, let windows install the
drivers. Now you may flash any firmware to the player, after finding a compatible update program.
You may need to do this process lots of time before getting a successful short.
But, if you don't find your board there, them you will have to find it yourself, by attempt and error. We
unhappily CAN'T help you hunting. (Google can.)
All the firmwares we have collected so far are on the forum, get them and start trying. Post your
complete experiences on the forum, so, with some time, we will catalogue all the FW files.
If you have a friend with a identical player it's easy, just ask him to extract the bin file from his player
using La aplicación de Wire.
The most important is to keep faith, LOTS of people already recovered their players!
● Principal
●Index
● Mapa del Web
● Documentación
Espec. Hardware
●
● Manuales
● Guías avanzadas
● Descargas
● Firmware list
● Aplicaciones y Utilidades
● Desarrollo
● Tareas por hacer
● Available works
● Enlaces
● Página de Enlaces
We need developers for the SWAN project! Subscribe and post here if you can help!
Aplicaciones y Utilidades
Site Map > Descargas > Aplicaciones y Utilidades
● 2. La aplicación de Wire
● 3. Arte (tipos de letra e imagenes)hechos por los usuarios
● 4. Herramienta de modificación del Firmware
● Procuct tools v 2.8 [download] (industry flashing tool. Can flash more than one player at the same time.)
1. Run BatchProduct.exe; 2. Go to "Replace firmware" and provide the firmware you are flashing ; 3. Click "Begin Download" to
flash the firmware. Note: If "begin download" is not clicable, click "Read record" till your mp3 player gets recognized by the
program.
Note: For the updater programs to work, windows must recognize the player first! (see Instale los drivers y haga que Windows
detecte el reproductor)
Wire has tracked all the update tool routine. If you need information, ask him.(wire at s1mp3.de).
2. La aplicación de Wire
If you need to help using s1fwx or s1res, you can check the guides at Guías avanzadas or see (http://www.s1mp3.de)
S1fwx
Firmware extractor. Can dump firmware directly from the mp3 player. Can extract code and resource files from any type of firmware
for the s1 mp3 player. See more information on the Guías avanzadas
Version 2.6
s1fwx_v26.zip : [download]
S1res
You can use s1res to change the firmware you have extract with s1fwx. You can modify the images and the text, even for MP4
players with colour OLED screen. See more information on the Guías avanzadas.
Version 1.5
s1res_v15.zip : [download]
Download
Name Type of artwork Author
Link
South Park [7z file] Bootlogo animation Andres Villegas
Parental Advisory [7z file] Bootlogo animation Andres Villegas
cartoons [7z file] Bootlogo colection Unknown
animal [7z file] Bootlogo colection Unknown
festival [7z file] Bootlogo colection Unknown
love [7z file] Bootlogo colection Unknown
festival [7z file] Bootlogo colection Unknown
others [7z file] Bootlogo colection Unknown
MenuPix v1.0 (+RU&UA text menus) [7z file] Complete pack alex_ua
s1mod.7z : [download]
● Telbook_v1.0.7z [download]
● Telbook_v1.1.7z [download]
● Telbook_v2.0.7z [download]
● Principal
● Index
● Mapa del Web
● Documentación
Espec. Hardware
●
● Manuales
● Guías avanzadas
● Descargas
Firmware list
●
● Aplicaciones y Utilidades
● Desarrollo
● Tareas por hacer
● Available works
● Enlaces
● Página de Enlaces
We need developers for the SWAN project! Subscribe and post here if you can help!
Guías avanzadas
Site Map > Documentación > Guías avanzadas
● 1. Guía s1fwx
● 2. Guía s1res
1. Guía s1fwx
(taken from http://www.stud.uni-karlsruhe.de/~uwa8/s1mp3/?Tools.s1fwx)
s1fwx (s1 firmware extractor) is a free commandline tool (public domain) which lets you extract the
original firmware from your s1 mp3 player device.
Additional features support operations on the firmware files like decrypt, extract and archive. This way
you could investigate all the files included in any fw file, change their content and put them back
together.
● AFI: this archives include files needed to flash the device, a minimal set may consist of an
BRECFxxx.BIN (the bootloader) and a FWIMAGE.FW file (see below)
● FW/FWI: firmware image files include all firmware files needed during runtime
Commandline usage:
usage: s1fwx {i|x|s|a|l|f|r} {filename{:[afi|fw|enc]}} examples: display file info s1fwx i fname.ext extract
firmware file s1fwx x fname.ext generate script from file s1fwx s fname.ext > new.script create
firmware file by script s1fwx a new.fw:fw < def_fw.script create afi file by script s1fwx a new.bin:afi <
def_afi.script list entire content of any file s1fwx l *.bin extract firmware from player s1fwx f dump.bin
repair dumped firmware files s1fwx r dump.bin
Extracting your players firmware is a very good idea just to create a backup of the original firmware
files. It's no promise that you could always backup your player after some bad firmware update, but at
least you have some more possibilities.
First download newest version(La aplicación de Wire) of s1fwx and extract the archive. Then connect
your mp3 player device to your computers USB port and wait until it gets detected. Now double click
the extracted file "extract.bat" or run
s1fwx f dump.bin
from the windows commandline console. Skip the disclaimer by pressing space and select the drive your
player gets mounted to. (eg. if detected drives displays " <x> " then choose drive "x:" by pressing x)
Now s1fwx should start extracting your firmware, this may take around 10 seconds.If all went well and
no error gets displayed it will display the content of the extracted firmware file as it was read from your
player.
Before you can update your player with this firmware file using the original "Mp3 Player Update Tool"
you will first have to repair it. Start "repair.bat" or type
s1fwx r dump.bin
A backup will be saved at "dump.bi$" automatically and the repaired file is now available as "dump.
bin". Notice that its not possible to do a firmware recovery with this file (only regular firmware updates)
since there are missing files needed by the "Mp3 Player Update Tool" recovery mode.
Since this files couldn't be found on your player you will need to get them from some official firmware
file which is known to work with your players hardware. Either you first could recover to this firmware
before updating to "dump.bin", or you could insert the needed files from the original AFI file into "dump.
bin" using s1fwx. The original firmware has to support your flash chip(s). It doesn't matters if its just
using different backlight or key-mapping.
Here some example how to extract the whole content of the AFI file "firmware.bin".
Place firmware and s1fwx in one folder, open commandline console (run "cmd") and go to the folder
containing the files. To extract the AFI and the firmware files, type:
Now you should have extracted all the files usually included in some general firmware file.
To modify files in a firmware you will have to extract, modify and then archive the files back together to
one AFI file.
First generate the script from the firmware file "firmware.bin", using:
Then extract the files and modify their content if you want. if you want to add or remove files or change
file specific parameters edit the generated script using an usual text editor (i think the syntax is self
explaining).
Flashing your player with an extracted firmware file is a very simple procedure, just take care you
repaired the extracted file (see above) and use the latest "MP3 Update Tool" available at the download
section.
This works good until the day we flash our player with some partial corrupted firmware (a total
corrupted firmware will damage the player permanently) and the update tool tells something about
recovery mode and just opens an open-dialog. (maybe you will have to open your player and short some
pins to get to this point, read the forum for further instructions).
If you select an extracted firmware file now, it just displays "Invalid upgrade firmware file". This isn't a
bug of s1fwx! The problem is that recovering needs some extra files included inside our AFI-file that
isn't needed for simple flashing. This files couldn't be found on the players flash, the only source is to
look for them inside some original firmware files.
There are two methods to solve this problem and each of them expects you could find some original
firmware file which is compatible to your players hardware and extracted firmware.
[Method 1]
[Method 2]
● - extract the extracted and the official firmware file using s1fwx (only the AFI part)
● - generate a script for both files ("s1fwx s dump.bin >dump.script")
● - merge the scripts to some new script file using a text editor
2. Guía s1res
(taken from http://www.stud.uni-karlsruhe.de/~uwa8/s1mp3/?Tools.s1fwx)
s1res (s1 resource editor) is a free win32 gui licensed as public domain.(La aplicación de Wire)
To change graphics or text on the S1 MP3 Player, just extract and repair your firmware using s1fwx.
Then run s1res and edit the extracted firmware file directly. Save the file and upload it using the original
MP3 Update Tool.
● Principal
● Index
● Mapa del Web
● Documentación
Espec. Hardware
●
● Manuales
● Guías avanzadas
● Descargas
Firmware list
●
● Aplicaciones y Utilidades
● Desarrollo
● Tareas por hacer
● Available works
● Enlaces
● Página de Enlaces
We need developers for the SWAN project! Subscribe and post here if you can help!
Manuales
Site Map > Documentación > Manuales
Cuando se reproduce una cancion que tiene un archivo .lrc asociado, aparecera una pequeña "L" (o "T"
en algunos otros firmwares) en el icono de musica. Entonces, para mostrar las letras de las canciones,
presione el boton de "modo" durante 3 o 4 segundos.
La funcion de letras de canciones tiene varios errores, por ello trate de mantener las letras tan simples
como sea posible. Use los rotulos de tiempo en este formato:
El archivo .lrc debe ser guardado con codificacion ANSI normal. Notepad puede hacer esta tarea.
Tambien hay algunas herramientas libres y comerciales para hacer los archivos .lrc. Busque en la web, y
use el que mas le guste.
El problema de reinicio es causado por la estatica. Para minimizar/resolver el reinicio, deberia aislar
completamente su reproductor del exterior.
Este es un asunto dificil de hacer, porque la cubierta tiene una parte metalica que mantiene el conector
USB y el microfono en contacto con el exterior y por ello permite que la electricidad estatica "entre" al
dispositivo y lo reinicie.
Tiene que abrir el reproductor y aislar las partes. Si no sabe como abrir su reproductor, chequee
Desmonte el s1mp3.
Para aislar estas partes, puede usar cinta pegante comun, o cualquier material aislante grueso.
He aislado las placas, los tornillos, el conector USB, el microfono, y la parte metalica que lo toca.
Para verficar si funciona, puede poner su reproductor cerca de un TV/monitor cargado y ver si se
reinicia. Usando un multimetro puede verificar si su aislamiento es bueno.
● Principal
● Index
● Mapa del Web
● Documentación
Espec. Hardware
●
● Manuales
● Guías avanzadas
● Descargas
Firmware list
●
● Aplicaciones y Utilidades
● Desarrollo
● Tareas por hacer
● Available works
● Enlaces
● Página de Enlaces
We need developers for the SWAN project! Subscribe and post here if you can help!
Espec. Hardware
● 4. Actions ATJ2085[CPU][RAM][ROM]
● 7. La placa LCD
● 8. La cabecera ICE
● [1]Conector USB
● [2]Bobinas de radio
● [3]Colector ICE
● [5]Numero de la placa
● [6]Switch (hold)
● [8]Boton de Modo
● [9]Microfono
● [13]Cristal
2. El esquemático
Se ha hallado un pdf con los diagramas electricos
Descargarlo :[Samograj_atj2085.pdf]
He tratado de realizar algun trabajo por mi cuenta. Está realmente sucio, por lo cual no lo estoy colocando aqui. Si esta
interesado en el cableado, envieme un email.
El numero usualmente esta detras de un adhesivo plastico, cerca del polo negativo de la bateria.
Si necesita ayuda para abrir el reproductor, vea un tutorial aqui: Desmonte el s1mp3.
Si tiene problemas para encontrar su numero de placa, puede estar detras del cable LCD. Es
posible que tenga que levantarlo cuidadosamente para ver el numero de la placa. Busque por
todas partes! Algunas personas les toma un tiempo encontrar las pequeñas palabras en blanco. Calificamos cualquier cosa
impresa en blanco sobre el circuito impreso verde como el numero de placa.
El mio dice :
2004-00-20 MP-482C MAIN V8
4. Actions ATJ2085[CPU][RAM][ROM]
El ATJ2085 es un SoC de audio. Por dentro, tenemos un nucleo de Z80, 29KB de ROM y 116KB de SRAM. Y un "DSP de
arquitectura Harvard de 24-bit". Ambos tienen un DSU on-chip.
Ya tenemos alguna informacion adicional del ATJ2085, si necesita conocer mas, contactenos en la lista de correo.
ds_k9w8g08u1m_rev07.pdf
7. La placa LCD
La placa LCD esta compuesta de un boton y un LCD (y unos pocos transistores/resistencias). Esta conectado a la placa
principal por un cable de 20 pines. En algunos reproductores, la placa LCD puede albergar tambien una memoria flash
NAND.
8. La cabecera ICE
Hay poca informacion disponible. Es un colector de 5 pines, conectado directamente a las patas ICERST#, ICEEN#,
GPO_A0, GPO_A2 y GPO_A3 del ATJ2085. Estos ultimos tres funcionan como ICEDI, ICEDO e ICECK.
Si considera que puede ayudarnos a hacer funcionar el ICE, por favor contactenos en la lista de correo.
● Nucleo de CPU Z80 de 8 bits con DSU on-chip (corre a 24.576MHz(TYP), hasta 60MHz - controlado por software)
● USB 1.1 - Aunque la mayoria de vendedores dicen que soporta USB 2.0, se refieren a que el dispositivo es
"compatible" con este protocolo, no a que sea un dispositivo capacitado para el modo de plena velocidad.
● Soporta velocidad de transferencia hasta 8Mbit/s, o 1MB/s
● Soporta MPEG1/2/2.5 Audio Layer 1, 2, 3 and WMA. (No estamos seguros si son posibles otros formatos de musica)
● Potencia de salida: 5mW x 5mW (16 ohm) [no ha sido probado todavia]
● S/N (relacion señal a ruido) 90dB [no ha sido probado todavia / EN VOLUMEN BAJO LA SNR ES REALMENTE
ALTA!]
● Grabar y reproducir voz (sin codificacion MP3, para la mayoria de reproductores s1mp3)
El firmware de fabrica del s1 mp3 puede soportar hasta un reproductor de musica, un grabador de voz, un reproductor
de archivos internos, radio fm, un menu de configuracion del sistema, un listado telefonico* y un lector de archivos
TXT*
● No soporta subdirectorios
LCD1 NT7502
1 48 VCC
NC NC
2 47
K1 K2 K3 NC IRS
LIBAT1 1 8 3 46
D1 D2 NC HPM
KEYO1 6 1 2 7 4 45 VCC
VSS DOUT S11 S22 FR P/S
5 2 3 6 5 44 GND
VDD V- S12 S21 CL C86 LR1 10K
4 3 4 5 6 43
Ct COUT G1 G2 DOF CLS
C18 C17 C16 7 42
K4 K5 NC M/S
LCMCE- 8 41 LC9 104
U23 U22 5N20V CS1 VR
KEYO2 104 104 103 VCC 9 40
D CS2 V0 D
521A LCMRST 10 39 LC8 104
RES V4
J1 J2 LCMA0 11 38
A0 V3
KEYI1
KEYI2
KEYI0
R90 MWR- 12 37 LC7 104
100R WR V2
R100 MRD- 13 36
RD V1
D0 14 35 VCC LC6 104
1K D0 VRS
C24 47U D1 15 34
D1 VEXT
D2 16 33 LC4 224 LC5 104
D2 C2-
J2 D3 17 32
D3 C2+
USBPOWER U17 VCC L1 AVCC D4 18 31
1 D1 D4 C1+
R5 24 USBD- 1N4148 220UH D5 19 30
XC6206P332M VCC D5 C1-
2 R6 D6 20 29 LC2 LC3
USB Port USBD+ USBPOWER 3 2 D6 C3+
3 R4 24 VIN VOUT D7 21 28 224 224
4 4R7 D7 NC
+ C70 + + 22 27
C66 DUTY0 VOUT
G
R7 C65 23 26
224 DUTY1 VSS
1 22K 47UF 24 25 LC1
47uF VDD VDD2
S1 2 224
1
J7 POWER SW 3
CON16PIN
VBAT J8
D6 1 16 D7 AVDD U9
1 16 XC6206P152M VDDIO R11 D6 1 16 D7
D5 2 15 ELENA VDD AVDD 1 16
2 15 3 2 VREFI 0R D5 2 15 ELENA
D4 3 14 D0 VIN VOUT R8 2 15
3 14 D4 3 14 D0
D3 4 13 D1 51K 3 14
4 13 + + L2 D3 4 13 D1
LCMCE- 5 12 D2 C9 + + + 4 13
G
5 12 C49 C15 220uH LCMCE- 5 12 D2
LCMRST 6 11 LCMA0 C67 C68 C69 5 12
6 11 10uF 224 10uF LCMRST 6 11 LCMA0
GND 7 10 MWR- 10uF 47uF 47uF 6 11
7 10 GND 7 10 MWR-
VCC 8 9 MRD-
1
8 9 7 10
VCC 8 9 MRD-
C 8 9 C
LCM BOARD
CON16PIN
VCC
GREEN
J6 LL1 C31 LED EL R22
4
+
AOUTL
100M@600R 220uF 100R
3 C11
ICECK LCMRST
LL2 HOSCO
ICEDI LCMA0
2 C32 ELENA
+
AOUTR Q2
1 100M@600R
FLASHCE1-
FLASHCE2-
220uF 15pF MMBT 2222
R2 10K
Y1
ICERST-
LCMCE-
ICEEN-
KEYO2
KEYO1
KEYO0
PHONEJACK STEREO
ICEDO
KEYI2
VDD VCC 24.576M
VDD
VCC
C34 C33 BLUE
Ear Phone L7 103 103
C7 C8 HOSCI
C12
LED EL1 R23
10UH
R10 R9 VMIC NGND
48 220R
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
20 20 224 224 15pF
GPIO1 R18 Q3
10K MMBT 2222
ICEEN#
GPIO_B6
GPIO_B5
GPIO_B4
GPIO_B2
VCC
ICERST#
GPO_A0
GPO_A2
GPO_A1
VDD
CE1#
CE2#
CE3#
LXVCC
NGND
+ R15
C38 RED
224 2.2K
GND 49 32
GND LXVDD LED EL2 R24
D7 50 31 VBAT
D7 BAT
D6 51 30 GND 360R
D6 GND
MIC1 C37 D5 52 29 KEYI1
D5 GPIO_B1 KEYO0 R20 Q4
EM5BPS 104 D4 53 28 ELENA
D4 GPIO_C2 MMBT 2222
D3 54 U1 27 KEYI0 10K
B MICIN D3 GPIO_B0 B
D2 55 26 VCC
D2 DCDIS
D1 56 ATJ2085 25
D1 BATSEL
D0 57 24 HOSCO
D0 HOSCO
MWR- 58 23 HOSCI
MWR# HOSCI
MRD- 59 22 VCC
MRD# LRADC
CLE 60 21 VCC
FMVCC CLE VP
ALE 61 20 VDDIO
12
37
ANT ALE VDDIO
FMDAT 62 19 AVDD
GPIO_C1 AVDD
GPIO_G0
63 18 U7
RESET#
FMCLK VREFI
AOUTR
PAGND
AOUTL
PAVCC
USBD+
FMINR
FMINL
GPIO_C0 VREFI
USBD-
MICIN
AGND
VRDA
VMIC
VCC
VCC
C23 VDD AVCC
100pF 10K 10K
19 44 D7
VCC
FM1 WP I/O7
L3 C20 MWR- 18 43 D6
Q1 1 10 FMGND WE I/O6
22UH ANT GND ALE 17 42 D5
1
2
3
4
5
6
7
8
9
AGND 10
11
MICIN 12
13
FMINL 14
FMINR 15
16
FLASHCE1- 9 32
AOUTL
GND SCL D3
USBD+
USBD-
VRDA
0
GPI01
GND
FLASHCE2- 10 31 D2
VCC
VSS
VSS
R3
1K C19 C10
C3 C4 C5
R19 R28 ROUT C6 +
10k 2M C27 R12 C26 224 224
R14 1K C1 C2 224 224 224 K9K1G08U0M
13
36
ROUT R13 1K FMINL
FMINR 47U 104 474
1K
ICEDO C28 1U 1U
C25
103 103
A A
http://dickys.8u8.com
QQ:19529829
13714315420
1 2 3 4 5 6 7 8
home
download
documentation
mailing lists Sponsors
wiki Rockbox is an open source replacement firmware for mp3 players. It runs on a number of different
models:
IRC
forums ● Archos: Jukebox 5000, 6000, Studio, Recorder, FM Recorder, Recorder V2 and Ondio
daily builds ● iRiver: H100 and H300 series Contactor Data AB
sponsors bandwidth and
CVS builds ● Apple: iPod 4th gen (grayscale and color), 5th gen (Video), Nano and Mini 1st/2nd gen server for the main site.
feature requests ● iAudio: X5 (including X5V and X5L)
bug reports ● Additional models are in development
patches
Rockbox is a complete rewrite and uses no fragments of any original firmwares. Why Choose Rockbox? Haxx sponsors the
download server and
bandwidth, as well as
various other resources.
News
Search
2006-08-23: Where are the Rockboxers?
Many people have
sponsored us with personal
2006-07-18: The feature freeze is lifted Paypal donations. Thank
you!
2006-07-07: Site is back up again after a few days downtime due to yet another break-in/attack. The twiki parts are still
disabled and will be brought back once we believe we have them "secured" properly.
2006-02-23: We have migrated to a new bugtracker: Flyspray. It's faster and better in practically every aspect. See it here.
More news
Allow
scrolling
lines with
firmware/drivers/lcd-16bit.c 1.36 different x-
firmware/drivers/lcd-2bit-horz.c 1.19 margins.
firmware/drivers/lcd-h100-remote.c 1.62 The margin
23 Aug 20:07 Mark Arigo at the time
firmware/drivers/lcd-h100.c 1.53
of the call to
firmware/drivers/lcd-recorder.c 1.85 puts_scroll
firmware/drivers/lcd-remote-2bit-vi.c 1.3 will be used
as the
margin for
that line.
Add optional
apps/gui/icon.h 1.8 icon to list
apps/gui/list.c 1.31 title, current
path display
23 Aug 20:02 Mark Arigo apps/gui/list.h 1.26
shows a dir
apps/settings.c 1.409
icon, and list
apps/tree.c 1.436 titles now
left-justified.
Ooops, the
sim doesn't
23 Aug 17:49 Jens Arnold firmware/SOURCES 1.107 understand
coldfire
asm...
Download
rockbox-2.5-ondiosp.zip rockbox-2.5-install.exe
rockbox-2.5-ondiofm.zip
(620 KB) (1.4 MB)
(462 KB)
Installation
Unpack the entire zip archive in the root (top) directory of your Archos disk. Make sure you stop/eject/unmount the
usb disk before you unplug it. Note: All files in the zip file are needed, don't just install a few of them.
Windows users can also use the the installer: Simply select your model and destination drive.
● Voice files
Uninstallation
If you ever want to remove the Rockbox firmware, simply delete archos.mod (player) or ajbrec.ajz (recorder) and
the .rockbox directory from the root of your Archos disk.
Source code
rockbox-2.5.tar.gz
Manual
We have a very nice manual written by Christi Scarborough. Please read it. Check out the documentation page for
further info.
Donate
If you enjoy using Rockbox, consider donating to the project. While we develop the software in our spare time,
equipment and players cost real money.
Daily Builds
Archos
Archos Archos Archos
Archos FM FM Archos Archos Ondio Archos
Player/ Recorder Recorder
Recorder Recorder Recorder v2 FM Ondio SP
Studio v1 8MB
8MB
latest / old latest / old latest / old latest / old latest / old latest / old latest / old latest / old
latest / old latest / old latest / old latest / old latest / old latest / old latest / old latest / old
latest / old latest / old latest / old latest / old latest / old
Bug reports
benefits.
Broadband Camcorders Cameras Desktops DVD & PVR Games Home Theatre Laptops Mobile Phones MP3 Players PDAs & GPS Projectors TVs Wi-Fi More
Hide the left column Liquid design MP3 Players : Music Software
aA
A
Cowon iAudio
Apple iPod
Updating the firmware on your iPod is for the most part
an automatic process. Updates for the iPod usually unlock
a cool new feature, such as compatibility with accessories
such as the Camera Connector.
iRiver
It used to be somewhat of a pain to update iRiver
firmware, but it's become much easier. Occasionally,
you'll run into firmware for an international version of the
device that can open up new features (such as video on
the H300 series), but iRiver does not recommend this.
Cowon iAudio
Cowon may not be a famous brand, but MP3 insiders
definitely know that the iAudio series includes some of
the most technologically advanced and best-sounding
MP3 players available. Updating Cowon's firmware takes
a couple of extra steps, but it's pretty easy overall.
Cowon is particularly proactive about updating its
file:///H|/mp3player/- Music Software.htm (4 of 14)30/08/2006 02:49:43 p.m.
- Music Software
Comments