Professional Documents
Culture Documents
U
B
A
-C
LOAD CHARTS
IN
TMS760E
R
FO
85% STABILITY
T
O
N
SERIAL NUMBER
TMS760E - S/N 1
TMS760E - S/N
N
O
T
FO
R
IN
-C
A
B
U
SE
2
TABLE OF CONTENTS
SE
FOLDING EXTENSION 360° ....................................................................................... 11
ON OUTRIGGERS FULLY RETRACTED
MAIN BOOM 360° ........................................................................................................ 12
U
FOLDING EXTENSION 360° ..................................................................... PROHIBITED
B
ON OUTRIGGERS FULLY EXTENDED
MAIN BOOM 360° ........................................................................................................ 13
A
MAIN BOOM OVER REAR .......................................................................................... 14
-C
FOLDING EXTENSION 360° ....................................................................................... 15
ON OUTRIGGERS HALF EXTENDED
MAIN BOOM 360° ........................................................................................................ 16
IN
WITH NO COUNTERWEIGHT
ON OUTRIGGERS FULLY EXTENDED
MAIN BOOM 360° ........................................................................................................ 25
MAIN BOOM OVER REAR .......................................................................................... 26
FOLDING EXTENSION 360° ....................................................................................... 27
ON OUTRIGGERS HALF EXTENDED
MAIN BOOM 360° ........................................................................................................ 28
FOLDING EXTENSION 360° ....................................................................................... 29
ON OUTRIGGERS FULLY RETRACTED
MAIN BOOM 360° ........................................................................................................ 30
FOLDING EXTENSION 360° ..................................................................... PROHIBITED
TMS760E - S/N 3
NOTES FOR LIFTING CAPACITIES
GENERAL:
1. Rated loads as shown on lift chart pertain to this machine as originally manufactured and equipped. Modifications to the machine or use
of optional equipment other than that specified can result in a reduction of capacity.
2. Construction equipment can be hazardous if improperly operated or maintained. Operation and maintenance of this machine shall be in
compliance with the information in the Operator’s and Safety Handbook, Service Manual, and Parts Manual supplied with this machine.
If these manuals are missing, order replacements from the manufacturer through the distributor.
3. The operator and other personnel associated with machine shall fully acquaint themselves with the latest American National Safety
Standards (ASME/ANSI) for cranes.
SETUP:
1. The machine shall be level and on a firm supporting surface. Depending on the nature of the supporting surface, it may be necessary to
have structural supports under the outrigger floats or tires to spread the load to a larger bearing surface.
2. For outrigger operation, outriggers shall be properly extended with tires raised free of crane weight before operating the boom or lifting
loads.
3. When machine is equipped with center front stabilizer, the front stabilizer shall be set in accordance with instructions in Operator's &
Safety Handbook.
4. When equipped with removable and/or extendible counterweight, the proper counterweight shall be installed and fully extended before
and during operation.
SE
5. If crane is approved by the manufacturer for on-rubber lifting, tires shall be inflated to the recommended pressure before lifting on rubber.
6. With certain boom and hoist tackle combinations, maximum capacities may not be obtainable with standard cable lengths.
7. Unless approved by the crane manufacturer, do not travel with boom extension or jib erected. Refer to the Operator's and Safety
Handbook for job-site travel information.
U
8. When operating on rubber, do not swing boom over the sides. Loss of backward stability will occur causing a backward tipping
condition.
OPERATION:
1. Rated loads at rated radius shall not be exceeded. Do not attempt to tip the machine to determine allowable loads. For clamshell or
B
concrete bucket operation, weight of bucket and load must not exceed 80% of rated lifting capacities.
2. All rated loads have been tested to and meet minimum requirements of SAE J1063 - Cantilevered Boom Crane Structures - Method of
A
Test, and do not exceed 85% of the tipping load on outriggers fully extended. On outriggers 50% and 0% extended (fully retracted), the
crane's stability was determined in compliance with ISO 4305-1991 and prEN 13000 - 1997, and also complies with DIN 15019.2 (Test
-C
Load = 1.25P + 0.1A) . 0.1A represents one tenth (0.10) of the total boom weight reduced to the boom point. Loads are also determined
by SAE J765 - Crane Stability Test Code.
3. Rated loads include the weight of hookblock, slings and auxiliary lifting devices and their weights shall be subtracted from the listed
rating to obtain the net load to be lifted. When more than the minimum required hoist reeving is used, the additional rope weight shall be
IN
7. Do not operate at a radius or boom length where capacities are not listed. At these positions, the machine may overturn without any
load on the hook.
8. The maximum load which can be telescoped is not definable because of variations in loadings and crane maintenance, but it is safe to
attempt retraction and extension of the boom within the limits of the capacity chart.
9. When the boom length or lift radius or both are between values listed, the smallest load shown at either the next larger radius or next
longer or shorter boom length shall be used.
T
10. For safe operation, the user shall make due allowances for his particular job conditions, such as: soft or uneven ground, out of level
conditions, high winds, side loads, pendulum action, jerking or sudden stopping of loads, experience of personnel, two machine (tandem)
O
lifts, traveling with loads, electric wires, obstacles, hazardous conditions, etc. Side pull on boom or jib is extremely dangerous.
11. If machine is equipped with individually controlled powered boom sections, the boom sections must be extended equally at all times.
N
12. Never handle personnel with this machine unless the requirements of the applicable national, state, and local regulations and safety
codes are met.
13. Keep load handling devices a minimum of 42 inches (107 cm) below boom head at all times.
14. The boom angle before loading should be greater than the loaded boom angle to account for deflection.
15. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation.
16. Capacities for the 10.8 m boom length shall be lifted with boom fully retracted. If boom is not fully retracted, capacities shall not exceed
those shown for the 12.2 m boom length.
17. When lifting over front of machine, radii less than 35 feet (12 meters) not recommended.
18. When operating the machine in the "On Outriggers 50% Extended (4.3 m spread)" mode, the outrigger beam pins must be engaged. When
operating the machine in the "On Outriggers 0% Extended (2.4 m spread)" mode, the outrigger beams must be fully retracted. Failure to
follow these precautions could result in structural damage or loss of stability of the machine.
19. Do not lift loads when boom is fully lowered. The Load Moment Indicator (LMI) senses pressure and will not provide warnings or
lockout. The crane can become overloaded if lift cylinder(s) is fully retracted.
20. WARNING: Lifting with the 10.1 m extension base, with the 7.0 m extension fly either erected or folded along side of extension base, is
strictly prohibited.
21. The maximum outrigger pad load is 41,225 kg.
DEFINITIONS:
1. Operating Radius: Horizontal distance from a projection of the axis of rotation to the supporting surface before loading to the center of
the vertical hoist line or tackle with load applied.
2. Loaded Boom Angle (Shown in Parenthesis on Main Boom Capacity Chart): is the angle between the boom base section and the
horizontal, after lifting the rated load at the rated radius with the rated boom length.
3. Working Area: Areas measured in a circular arc about the center line of rotation as shown on the working area diagram.
4. Freely Suspended Load: Load hanging free with no direct external force applied except by the lift cable.
5. Side Load: Horizontal force applied to the lifted load either on the ground or in the air.
TMS760E - S/N 4
SE
U
B
A
-C
LINE PULLS AND REEVING INFORMATION
IN
PERMISSIBLE NOMINAL
HOISTS CABLE SPECS.
LINE PULLS CABLE LENGTH
TMS760E - S/N 5
TMS760E - S/N
N
O
T
FO
R
IN
-C
A
B
U
SE
6
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 7,485 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
U
37,150 35,250 34,350 26,350 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
31,450 29,950 29,600 23,250 16,675 16,675 14,050 *13,200
6
B
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
27,475 26,200 25,675 20,575 16,675 15,925 13,775 12,625 *10,875
7
A
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
22,050 22,725 22,175 18,525 16,300 14,850 13,075 11,925 10,650
8
-C
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
13,725 18,375 18,075 17,375 15,275 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
IN
13,975 14,950 14,525 13,875 12,075 10,675 10,350 9,465
10
(20.5) (44) (54.5) (60.5) (65) (68.5) (71) (73)
10,775 10,325 10,625 10,125 9,275 8,770 8,475
12
(30) (45.5) (53.5) (59.5) (63.5) (67) (69.5)
R
20
(30.5) (41) (48) (53.5)
O
24
(24) (36) (43.5)
2,495 2,605
26
(28) (38)
2,015 2,140
28
(16) (31)
1,725
30
(22.5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 33.5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
TMS760E - S/N 7
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 7,485 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
37,150 35,250 34,350 26,350 16,675 16,675 *14,050
U
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
31,450 29,950 29,600 23,250 16,675 16,675 14,050 *13,200
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
B
27,475 26,200 25,675 20,575 16,675 15,925 13,775 12,625 *10,875
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
8
22,050
(32)
22,925
(42)
22,175
(54.5)
18,525
(62)
A
16,300
(66.5)
14,850
(70)
13,075
(73)
11,925
(75)
10,650
(77)
-C
13,725 20,375 18,475 17,375 15,275 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
13,975 16,125 15,125 13,875 12,075 10,675 10,350 9,465
IN
10
(20.5) (44) (54.5) (60.5) (65) (68.5) (71) (73)
12,175 11,800 10,975 10,125 9,275 8,770 8,475
12
(30) (45.5) (53.5) (59.5) (63.5) (67) (69.5)
R
22
(16.5) (35.5) (42.5) (48.5)
3,370 3,130 3,130
N
24
(24) (36) (43.5)
2,605 2,605
26
(28) (38)
2,220 2,170
28
(16) (31)
1,840
30
(22.5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 33.5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
TMS760E - S/N 8
10.1 m - 17.1 m FOLDING OFFSETTABLE BOOM EXTENSION
WITH 7,485 kg REMOVABLE COUNTERWEIGHT
ON OUTRIGGERS FULLY EXTENDED - 360°
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius
in #0021 #0022 #0023 #0041 #0042 #0043 are based on structural strength
Meters 0° 25° 45° 0° 25° 45° of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
*5,850 2. 10.1 m and 17.1 m boom exten-
9
(78) sion lengths may be used for
5,850 *3,775 single line lifting service.
10
(77) (78)
12
5,850 *4,920 3,775 3. Radii listed are for a fully extended
SE
(74.5) (78) (77.5)
boom with the boom extension
5,780 4,700 *3,360 3,775
14
(71.5) (76.5) (78) (76) erected. For main boom lengths
5,260 4,355 3,215 3,760 *2,400 less than fully extended, the rated
16
U
(69) (73.5) (76) (73.5) (78) loads are determined by boom
18
4,665 3,935 3,100 3,480 2,345 angle. Use only the column which
(66) (70.5) (73) (71.5) (77)
corresponds to the boom exten-
B
4,100 3,565 3,005 3,225 2,310 *1,750
20
(63) (67.5) (70) (69) (74.5) (78) sion length and offset for which the
A
3,715 3,250 2,920 2,990 2,250 1,690 machine is configured. For boom
22
(60.5) (64.5) (67) (66.5) (72) (76.5) angles not shown, use the rating
-C
3,345 2,980 2,800 2,690 2,100 1,620 of the next lower boom angle.
24
(57) (61) (63.5) (64) (69.5) (74)
26
2,910 2,740 2,610 2,425 2,020 1,560 4. WARNING: Operation of this ma-
IN
30
(46.5) (50.5) (52) (56) (61.5) (65) extension occurs rapidly and with-
1,720 1,910 2,030 1,830 1,640 1,460 out advance warning.
FO
32
(42.5) (46.5) (47.5) (53) (58.5) (62)
34
1,425 1,580 1,635 1,520 1,425 5. Boom angle is the angle above or
(38.5) (42) (50) (55.5) (58.5)
below horizontal of the longitudi-
1,165 1,285 1,370 1,410 1,350
36
(33.5) (37) (46.5) (52) (55)
nal axis of the boom base section
T
42
735 905 vertical jacks set only.
(34.5) (40.5)
560 700
44
(30) (35)
No Load Stability Data
Min. boom
angle for
indicated
20° 25° 45° 28° 28° 45°
length
Max. boom
length at 0° 30.5 m 27.4 m
boom angle
NOTE: ( ) Boom angles are in degrees. A6-829-101616
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
TMS760E - S/N 9
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 7,485 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
29,125 29,025 28,875 27,200 16,675
4
(63.5) (67) (72) (76) (77.5)
26,175 26,050 25,850 25,550 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
U
23,550 23,450 23,275 22,275 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
19,625 19,525 18,625 17,300 16,675 16,525 14,050 *13,200
B
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
15,675 15,700 14,900 13,875 13,750 13,525 13,250 12,625 *10,875
A
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
12,425 12,400 12,175 11,400 11,375 11,275 11,125 10,925 10,650
-C
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
10,100 10,075 9,910 9,500 9,575 9,560 9,485 9,370 9,235
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
IN
TMS760E - S/N 10
10.1 m - 17.1 m FOLDING OFFSETTABLE BOOM EXTENSION
WITH 7,485 kg REMOVABLE COUNTERWEIGHT
ON OUTRIGGERS 50% EXTENDED (4.3 m SPREAD) - 360°
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius are based on structural strength
in #4021 #4022 #4023 #4041 #4042 #4043
Meters 0° 25° 45° 0° 25° 45° of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
*5,850
2. 10.1 m and 17.1 m boom exten-
9
(78) sion lengths may be used for
10
5,850 *3,775 single line lifting service.
(77) (78)
SE
5,850 *4,920 3,775 3. Radii listed are for a fully extended
12
(74.5) (78) (77.5) boom with the boom extension
4,660 4,700 *3,360 3,775 erected. For main boom lengths
14
(71.5) (76.5) (78) (76)
less than fully extended, the rated
U
3,725 4,340 3,215 3,760 *2,400
16 loads are determined by boom
(69) (73.5) (76) (73.5) (78)
2,985 3,520 3,100 3,060 2,345 angle. Use only the column which
B
18
(66) (70.5) (73) (71.5) (77) corresponds to the boom exten-
2,385 2,850 3,005 2,485 2,310 *1,750 sion length and offset for which the
A
20
(63) (67.5) (70) (69) (74.5) (78)
machine is configured. For boom
1,895 2,300 2,430 2,005 2,250 1,690
-C
22 angles not shown, use the rating
(60.5) (64.5) (67) (66.5) (72) (76.5)
1,480 1,830 1,925 1,600 2,100 1,620 of the next lower boom angle.
24
(57) (61) (63.5) (64) (69.5) (74)
IN
1,125 1,435 1,500 1,255 1,815 1,560 4. WARNING: Operation of this ma-
26
(54) (57.5) (60) (61.5) (67.5) (71) chine with heavier loads than the
28
805 1,060 1,145 955 1,455 1,525 capacities listed is strictly prohib-
(50) (54) (56) (58.5) (64.5) (68)
R
515
36
(55)
after lifting rated load.
O
TMS760E - S/N 11
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 7,485 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
(66.5) (69.5) (74) (77.5) (78)
18,725 17,975 16,425 15,050 14,600
4
(63.5) (67) (72) (76) (77.5)
16,000 15,375 14,150 13,025 12,725 *12,375
U
4.5
(60) (64) (70) (74) (76.5) (78)
13,850 13,325 12,325 11,350 11,200 10,950 *10,675
5
B
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
10,325 10,250 9,500 8,830 8,825 8,730 8,590 *8,415
A
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
7,820 7,840 7,470 6,940 7,085 7,085 7,025 6,935 *6,820
-C
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
6,035 6,045 5,945 5,500 5,710 5,815 5,815 5,780 5,715
8
IN
0.1A (kg) 475 485 500 510 470 440 415 395 380
Minimum boom angle (deg.) for
0 21 30 36 41 45
indicated length (no load)
Maximum boom length (m) at 0 degree boom
18.4
angle (no load)
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
TMS760E - S/N 12
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 4,990 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
37,150 35,250 34,350 26,350 16,675 16,675 *14,050
U
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
31,450 29,950 29,600 23,250 16,675 16,675 14,050 *13,200
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
B
26,025 25,875 25,575 20,575 16,675 15,925 13,775 12,625 *10,875
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
8
20,050
(32)
20,000
(42)
19,650
(54.5)
18,525
(62)
A 16,300
(66.5)
14,850
(70)
13,075
(73)
11,925
(75)
10,650
(77)
-C
13,650 16,025 15,725 15,325 15,275 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
13,175 12,925 12,525 12,800 12,075 10,675 10,350 9,465
IN
10
(20.5) (44) (54.5) (60.5) (65) (68.5) (71) (73)
9,140 8,770 9,065 9,375 9,275 8,770 8,475
12
(30) (45.5) (53.5) (59.5) (63.5) (67) (69.5)
R
22
(16.5) (35.5) (42.5) (48.5)
2,240 2,395 2,540
N
24
(24) (36) (43.5)
1,885 2,025
26
(28) (38)
1,455 1,580
28
(16) (31)
1,205
30
(22.5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 33.5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
TMS760E - S/N 13
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 4,990 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
43,200 37,975 36,375 28,075 16,675
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
U
37,150 35,250 34,350 26,350 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
31,450 29,950 29,600 23,250 16,675 16,675 14,050 *13,200
B
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
26,825 26,025 25,675 20,575 16,675 15,925 13,775 12,625 *10,875
A
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
21,150 22,675 22,175 18,525 16,300 14,850 13,075 11,925 10,650
-C
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
13,650 19,400 18,475 17,375 15,275 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
IN
12
5,850 *4,920 3,775 3. Radii listed are for a fully extended
SE
(74.5) (78) (77.5)
boom with the boom extension
5,780 4,700 *3,360 3,775
14
(71.5) (76.5) (78) (76)
erected. For main boom lengths
5,260 4,355 3,215 3,760 *2,400 less than fully extended, the rated
16
U
(69) (73.5) (76) (73.5) (78) loads are determined by boom
18
4,665 3,935 3,100 3,480 2,345 angle. Use only the column which
(66) (70.5) (73) (71.5) (77)
corresponds to the boom exten-
B
4,100 3,565 3,005 3,225 2,310 *1,750
20
(63) (67.5) (70) (69) (74.5) (78) sion length and offset for which the
A
3,385 3,250 2,920 2,990 2,250 1,690 machine is configured. For boom
22
(60.5) (64.5) (67) (66.5) (72) (76.5) angles not shown, use the rating
-C
24
2,790 2,980 2,800 2,690 2,100 1,620 of the next lower boom angle.
(57) (61) (63.5) (64) (69.5) (74)
26
2,300 2,645 2,610 2,425 2,020 1,560 4. WARNING: Operation of this ma-
IN
30
(46.5) (50.5) (52) (56) (61.5) (65) extension occurs rapidly and with-
1,235 1,425 1,545 1,460 1,640 1,460 out advance warning.
FO
32
(42.5) (46.5) (47.5) (53) (58.5) (62)
34
975 1,125 1,185 1,520 1,425 5. Boom angle is the angle above or
(38.5) (42) (50) (55.5) (58.5) below horizontal of the longitudi-
745 860 945 1,235 1,350
36
(33.5) (37) (46.5) (52) (55)
nal axis of the boom base section
T
545 750
6.Capacities listed are with
40 outriggers properly extended and
(38.5) (45)
N
42
545 vertical jacks set only.
(40.5)
No Load Stability Data
Min. boom
angle for
indicated
25° 25° 45° 33° 36° 45°
length
Max. boom
length at 0° 27.4 m 24.4 m
boom angle
NOTE: ( ) Boom angles are in degrees. A6-829-101617
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
TMS760E - S/N 15
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 4,990 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
27,900 27,800 27,625 26,050 16,675
4
(63.5) (67) (72) (76) (77.5)
24,800 24,700 24,150 22,125 16,675 *16,675
4.5
U
(60) (64) (70) (74) (76.5) (78)
22,800 22,700 20,725 19,075 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
B
17,900 17,250 15,875 14,700 14,450 14,125 13,750 *13,200
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
7
13,525
(42)
13,500
(49)
12,600
(59.5)
11,675
(65.5)
A
11,625
(69.5)
11,450
(72.5)
11,250
(75)
11,025
(77)
*10,775
(78)
-C
10,550 10,525 10,175 9,490 9,540 9,495 9,390 9,255 9,095
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
IN
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius
#4121 #4122 #4123 #4141 #4142 #4143 are based on structural strength
in
Meters 0° 25° 45° 0° 25° 45° of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
*5,850
2. 10.1 m and 17.1 m boom exten-
9 sion lengths may be used for
(78)
10
5,850 *3,775 single line lifting service.
(77) (78)
SE
4,815 *4,920 3,775 3. Radii listed are for a fully extended
12
(74.5) (78) (77.5) boom with the boom extension
3,735 4,455 *3,360 3,770 erected. For main boom lengths
14
(71.5) (76.5) (78) (76)
less than fully extended, the rated
U
2,910 3,525 3,215 2,980 *2,400
16 loads are determined by boom
(69) (73.5) (76) (73.5) (78)
2,255 2,785 3,100 2,350 2,345 angle. Use only the column which
B
18
(66) (70.5) (73) (71.5) (77) corresponds to the boom exten-
1,725 2,185 2,415 1,835 2,310 *1,750 sion length and offset for which the
A
20
(63) (67.5) (70) (69) (74.5) (78)
1,285 1,690 1,860 1,410 2,115 1,690
machine is configured. For boom
22
-C
(60.5) (64.5) (67) (66.5) (72) (76.5) angles not shown, use the rating
24
915 1,270 1,405 1,050 1,680 1,620 of the next lower boom angle.
(57) (61) (63.5) (64) (69.5) (74)
IN
605 910 1,025 745 1,305 1,560 4. WARNING: Operation of this ma-
26
(54) (57.5) (60) (61.5) (67.5) (71) chine with heavier loads than the
600 705 980 1,295 capacities listed is strictly prohib-
28
(54) (56) (64.5) (68)
R
695 965
ited. Machine tipping with boom
30 extension occurs rapidly and with-
(61.5) (65)
FO
Min. boom
angle for
47° 44° 47° 50° 52° 54° after lifting rated load.
O
indicated
length
Max. boom
6.Capacities listed are with
N
TMS760E - S/N 17
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 4,990 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
Radius #8101
in Main Boom Length in Meters
Meters
10.8 12.2 15.2 **18.4 21.3 24.4 27.4 30.5 33.5
22,850 21,650 19,400 *17,475
3
(69) (72) (76) (78)
18,675 17,850 16,075 14,575 *12,050
3.5
SE
(66.5) (69.5) (74) (77.5) (78)
15,600 14,950 13,575 12,350 12,050
4
(63.5) (67) (72) (76) (77.5)
U
13,225 12,700 11,600 10,600 10,400 *10,150
4.5
(60) (64) (70) (74) (76.5) (78)
11,350 10,900 10,000 9,170 9,090 8,930 *8,720
B
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
8,390 8,240 7,565 6,980 7,035 7,005 6,915 *6,795
A
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
-C
6,215 6,215 5,805 5,335 5,530 5,575 5,560 5,510 *5,435
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
4,680 4,675 4,480 4,085 4,335 4,475 4,510 4,510 4,475
IN
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
3,535 3,530 3,445 3,105 3,390 3,575 3,670 3,700 3,705
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
R
615 725
16
O
(58) (62)
0.1A (kg) 475 485 500 510 470 440 415 395 380
N
TMS760E - S/N 18
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 2,495 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
43,200 37,975 36,375 28,075 16,675
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
U
36,500 35,250 34,350 26,350 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
30,400 29,950 29,600 23,250 16,675 16,675 14,050 *13,200
6
B
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
22,225 22,150 21,950 20,575 16,675 15,925 13,775 12,625 *10,875
7
A
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
16,875 16,875 16,675 16,475 16,300 14,850 13,075 11,925 10,650
8
-C
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
13,275 13,300 13,175 13,000 13,300 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
IN
SE
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
U
36,500 35,250 34,350 26,350 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
30,400 29,950 29,600 23,250 16,675 16,675 14,050 *13,200
6
B
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
25,650 25,400 25,175 20,575 16,675 15,925 13,775 12,625 *10,875
7
(42) (49) (59.5) (65.5)
A
(69.5) (72.5) (75) (77) (78)
20,200 21,425 21,275 18,525 16,300 14,850 13,075 11,925 10,650
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
-C
13,600 17,800 17,850 17,375 15,275 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
IN
13,300 14,675 14,650 13,875 12,075 10,675 10,350 9,465
10
(20.5) (44) (54.5) (60.5) (65) (68.5) (71) (73)
10,375 10,375 10,750 10,125 9,275 8,770 8,475
12
(30) (45.5) (53.5) (59.5) (63.5) (67) (69.5)
R
20
(30.5) (41) (48) (53.5)
3,180 3,535 3,705 3,845
O
22
(16.5) (35.5) (42.5) (48.5)
2,840 3,010 3,130
N
24
(24) (36) (43.5)
2,430 2,590
26
(28) (38)
1,945 2,105
28
(16) (31)
1,685
30
(22.5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 33.5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
TMS760E - S/N 20
10.1 m - 17.1 m FOLDING OFFSETTABLE BOOM EXTENSION
WITH 2,495 kg REMOVABLE COUNTERWEIGHT
ON OUTRIGGERS FULLY EXTENDED - 360°
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius
in #0221 #0222 #0223 #0241 #0242 #0243 are based on structural strength
Meters 0° 25° 45° 0° 25° 45° of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
*5,850 2. 10.1 m and 17.1 m boom exten-
9
(78) sion lengths may be used for
10
5,850 *3,775 single line lifting service.
(77) (78)
3. Radii listed are for a fully extended
SE
5,850 *4,920 3,775
12
(74.5) (78) (77.5)
boom with the boom extension
5,780 4,700 *3,360 3,775
14
(71.5) (76.5) (78) (76)
erected. For main boom lengths
less than fully extended, the rated
U
5,190 4,355 3,215 3,760 *2,400
16
(69) (73.5) (76) (73.5) (78) loads are determined by boom
18
4,115 3,935 3,100 3,480 2,345 angle. Use only the column which
B
(66) (70.5) (73) (71.5) (77)
corresponds to the boom exten-
3,295 3,565 3,005 3,225 2,310 *1,750
20 sion length and offset for which the
A
(63) (67.5) (70) (69) (74.5) (78)
2,650 3,070 2,920 2,990 2,250 1,690 machine is configured. For boom
22
angles not shown, use the rating
-C
(60.5) (64.5) (67) (66.5) (72) (76.5)
24
2,125 2,480 2,760 2,435 2,100 1,620 of the next lower boom angle.
(57) (61) (63.5) (64) (69.5) (74)
4. WARNING: Operation of this ma-
IN
1,695 2,000 2,225 1,975 2,020 1,560
26
(54) (57.5) (60) (61.5) (67.5) (71) chine with heavier loads than the
1,330 1,590 1,775 1,590 1,920 1,525
28
(50) (54) (56) (58.5) (64.5) (68)
capacities listed is strictly prohib-
ited. Machine tipping with boom
R
32
755 945 1,065 980 1,375 1,460 out advance warning.
(42.5) (46.5) (47.5) (53) (58.5) (62)
525 685 735 1,075 1,230 5. Boom angle is the angle above or
34
(38.5) (42) (50) (55.5) (58.5) below horizontal of the longitudi-
515 810 935 nal axis of the boom base section
T
36
(46.5) (52) (55)
580 670
after lifting rated load.
O
38
(49) (51)
6.Capacities listed are with
No Load Stability Data
N
TMS760E - S/N 21
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 2,495 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
26,800 26,700 24,225 21,925 16,675
4
(63.5) (67) (72) (76) (77.5)
23,625 22,475 20,325 18,525 16,675 *16,675
U
4.5
(60) (64) (70) (74) (76.5) (78)
20,000 19,100 17,350 15,900 15,475 15,000 *14,050
5
B
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
14,300 14,300 13,150 12,100 11,950 11,725 11,450 *11,150
6
A
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
10,675 10,675 10,300 9,490 9,500 9,420 9,285 9,110 *8,920
-C
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
8,305 8,275 8,125 7,585 7,690 7,700 7,650 7,560 7,450
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
IN
10
(20.5) (44) (54.5) (60.5) (65) (68.5) (71) (73)
FO
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius
#4221 #4222 #4223 #4241 #4242 #4243 are based on structural strength
in
Meters 0° 25° 45° 0° 25° 45° of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
2. 10.1 m and 17.1 m boom exten-
*5,850
9 sion lengths may be used for
(78)
5,040 *3,775 single line lifting service.
10
(77) (78)
3. Radii listed are for a fully extended
SE
3,755 *4,610 3,775
12
(74.5) (78) (77.5) boom with the boom extension
14
2,815 3,535 *3,360 2,880 erected. For main boom lengths
(71.5) (76.5) (78) (76)
less than fully extended, the rated
U
2,095 2,710 3,115 2,190 *2,400
16
(69) (73.5) (76) (73.5) (78) loads are determined by boom
1,520 2,055 2,395 1,640 2,345 angle. Use only the column which
18
B
(66) (70.5) (73) (71.5) (77) corresponds to the boom exten-
20
1,060 1,520 1,780 1,190 1,985 *1,750 sion length and offset for which the
A
(63) (67.5) (70) (69) (74.5) (78)
machine is configured. For boom
675 1,080 1,290 820 1,525 1,690
22 angles not shown, use the rating
-C
(60.5) (64.5) (67) (66.5) (72) (76.5)
710 885 505 1,130 1,550 of the next lower boom angle.
24
(61) (63.5) (64) (69.5) (74)
4. WARNING: Operation of this ma-
IN
28
505 815 capacities listed is strictly prohib-
(64.5) (68) ited. Machine tipping with boom
R
515
30
(65)
extension occurs rapidly and with-
FO
Max. boom
length at 0° 15.2 m 15.2 m 6.Capacities listed are with
boom angle
outriggers properly extended and
N
TMS760E - S/N 23
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH 2,495 kg REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
(66.5) (69.5) (74) (77.5) (78)
12,475 11,900 10,725 9,670 9,480
4
(63.5) (67) (72) (76) (77.5)
U
10,475 10,000 9,075 8,185 8,110 *7,950
4.5
(60) (64) (70) (74) (76.5) (78)
8,890 8,490 7,720 6,975 6,985 6,905 *6,775
B
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
6,290 6,225 5,640 5,130 5,250 5,280 5,245 *5,175
A
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
-C
4,420 4,380 4,145 3,735 3,975 4,070 4,100 4,090 *4,050
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
3,105 3,075 2,940 2,675 2,965 3,140 3,210 3,240 3,240
IN
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
2,120 2,100 1,990 1,840 2,160 2,375 2,500 2,560 2,585
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
R
0.1A (kg) 475 485 500 510 470 440 415 395 380
O
TMS760E - S/N 24
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH NO REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
43,200 37,975 36,375 28,075 16,675
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
U
(60) (64) (70) (74) (76.5) (78)
36,200 34,400 34,025 26,350 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
B
26,350 26,250 26,025 23,250 16,675 16,675 14,050 *13,200
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
A
18,700 18,600 18,400 18,200 16,675 15,925 13,775 12,625 *10,875
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
-C
14,050 14,050 13,850 13,650 13,975 14,325 13,075 11,925 10,650
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
10,925 10,975 10,850 10,650 10,975 11,300 11,625 11,075 10,050
IN
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
8,755 8,700 8,505 8,825 9,155 9,490 9,695 9,465
10
(20.5) (44) (54.5) (60.5) (65) (68.5) (71) (73)
R
SE
43,200 37,975 36,375 28,075 16,675
4
(63.5) (67) (72) (76) (77.5)
40,050 37,550 36,375 27,700 16,675 *16,675
4.5
(60) (64) (70) (74) (76.5) (78)
U
36,200 34,400 34,025 26,350 16,675 16,675 *14,050
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
29,025 28,650 28,475 23,250 16,675 16,675 14,050 *13,200
B
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
24,225 24,125 23,950 20,575 16,675 15,925 13,775 12,625 *10,875
A
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
19,250 19,450 19,475 18,350 16,300 14,850 13,075 11,925 10,650
-C
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
13,550 15,425 15,475 15,475 15,275 13,350 11,650 11,075 10,050
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
IN
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius
in #0821 #0822 #0823 #0841 #0842 #0843 are based on structural strength
Meters 0° 25° 45° 0° 25° 45° of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
*5,850 2. 10.1 m and 17.1 m boom exten-
9
(78) sion lengths may be used for
10
5,850 *3,775 single line lifting service.
(77) (78)
3. Radii listed are for a fully extended
SE
5,850 *4,920 3,775
12
(74.5) (78) (77.5)
boom with the boom extension
5,585 4,700 *3,360 3,775
14
(71.5) (76.5) (78) (76)
erected. For main boom lengths
less than fully extended, the rated
U
4,265 4,355 3,215 3,760 *2,400
16
(69) (73.5) (76) (73.5) (78) loads are determined by boom
18
3,295 3,915 3,100 3,480 2,345 angle. Use only the column which
B
(66) (70.5) (73) (71.5) (77)
corresponds to the boom exten-
2,555 3,070 3,005 2,850 2,310 *1,750
20 sion length and offset for which the
A
(63) (67.5) (70) (69) (74.5) (78)
1,970 2,405 2,670 2,250 2,250 1,690 machine is configured. For boom
22
angles not shown, use the rating
-C
(60.5) (64.5) (67) (66.5) (72) (76.5)
24
1,500 1,870 2,090 1,765 2,100 1,620 of the next lower boom angle.
(57) (61) (63.5) (64) (69.5) (74)
4. WARNING: Operation of this ma-
IN
1,110 1,425 1,615 1,365 1,845 1,560
26
(54) (57.5) (60) (61.5) (67.5) (71) chine with heavier loads than the
780 1,055 1,215 1,030 1,460 1,525
28
(50) (54) (56) (58.5) (64.5) (68)
capacities listed is strictly prohib-
ited. Machine tipping with boom
R
32
580 845 1,085 out advance warning.
(47.5) (58.5) (62)
600 780 5. Boom angle is the angle above or
34
(55.5) (58.5) below horizontal of the longitudi-
510 nal axis of the boom base section
T
36
(55)
after lifting rated load.
No Load Stability Data
O
TMS760E - S/N 27
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH NO REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
SE
(66.5) (69.5) (74) (77.5) (78)
23,475 22,175 19,800 17,825 16,675
4
(63.5) (67) (72) (76) (77.5)
19,375 18,375 16,500 14,925 14,500 *13,975
U
4.5
(60) (64) (70) (74) (76.5) (78)
16,300 15,525 13,975 12,700 12,450 12,100 *11,725
5
B
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
12,000 11,475 10,425 9,500 9,465 9,335 9,150 *8,930
A
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
8,855 8,765 8,020 7,290 7,380 7,375 7,300 7,190 *7,060
-C
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
6,560 6,575 6,225 5,680 5,845 5,915 5,915 5,875 5,805
8
IN
605 725
18
(53.5) (57.5)
N
0.1A (kg) 475 485 500 510 470 440 415 395 380
Minimum boom angle (deg.) for
0 25 33 39 44 48
indicated length (no load)
Maximum boom length (m) at 0 degree boom
18.4
angle (no load)
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
TMS760E - S/N 28
10.1 m - 17.1 m FOLDING OFFSETTABLE BOOM EXTENSION
WITH NO REMOVABLE COUNTERWEIGHT
ON OUTRIGGERS 50% EXTENDED (4.3 m SPREAD) - 360°
10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line
Radius
#4821 #4822 #4823 #4841 #4842 #4843
are based on structural strength
in
Meters 0° 25° 45° 0° 25° 45°
of boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
2. 10.1 m and 17.1 m boom exten-
*4,505
9
(78) sion lengths may be used for
3,795 *3,775 single line lifting service.
10
(77) (78)
SE
2,700 *3,550 2,760 3. Radii listed are for a fully extended
12
(74.5) (78) (77.5) boom with the boom extension
14
1,895 2,615 *3,065 1,995 erected. For main boom lengths
(71.5) (76.5) (78) (76)
less than fully extended, the rated
U
1,280 1,895 2,215 1,400 *2,400
16
(69) (73.5) (76) (73.5) (78) loads are determined by boom
790 1,325 1,575 930 1,825 angle. Use only the column which
B
18
(66) (70.5) (73) (71.5) (77) corresponds to the boom exten-
860 1,085 545 1,340 *1,750 sion length and offset for which the
A
20
(67.5) (70) (69) (74.5) (78)
machine is configured. For boom
690 930 1,410
-C
22
(67) (72) (76.5) angles not shown, use the rating
585 1,000 of the next lower boom angle.
24
(69.5) (74)
IN
645
4. WARNING: Operation of this ma-
26 chine with heavier loads than the
(71)
0.1A (kg) 370 340 325 350 325 295 capacities listed is strictly prohib-
R
angle for
indicated
56° 57° 58° 60° 62° 62° out advance warning.
length
Max. boom
5. Boom angle is the angle above or
length at 0° 12.2 m 10.8 m below horizontal of the longitudi-
boom angle
nal axis of the boom base section
T
TMS760E - S/N 29
RATED LIFTING CAPACITIES IN KILOGRAMS
WITH NO REMOVABLE COUNTERWEIGHT
10.8 m - 33.5 m BOOM
Radius #8801
in Main Boom Length in Meters
Meters
10.8 12.2 15.2 **18.4 21.3 24.4 27.4 30.5 33.5
14,425 13,525 11,875 *10,475
3
(69) (72) (76) (78)
11,525 10,900 9,600 8,510 *6,920
3.5
SE
(66.5) (69.5) (74) (77.5) (78)
9,375 8,900 7,880 6,980 6,920
4
(63.5) (67) (72) (76) (77.5)
U
7,725 7,325 6,535 5,770 5,800 *5,740
4.5
(60) (64) (70) (74) (76.5) (78)
6,415 6,080 5,425 4,785 4,880 4,885 *4,830
B
5
(57) (61.5) (68) (72.5) (75.5) (77.5) (78)
4,425 4,215 3,715 3,280 3,470 3,555 3,580 *3,565
A
6
(50) (55.5) (64) (69) (72.5) (75) (77) (78)
-C
2,935 2,895 2,485 2,135 2,430 2,570 2,645 2,670 *2,670
7
(42) (49) (59.5) (65.5) (69.5) (72.5) (75) (77) (78)
1,885 1,905 1,560 1,265 1,595 1,810 1,915 1,975 2,005
IN
8
(32) (42) (54.5) (62) (66.5) (70) (73) (75) (77)
1,095 1,115 835 580 930 1,175 1,335 1,415 1,470
9
(16) (33) (49.5) (58.5) (63.5) (67.5) (70.5) (73) (75)
R
0.1A (kg) 475 485 500 510 470 440 415 395 380
Min. boom angle (deg.) for
indicated length (no load)
0 36 49 53 56 58 61 63
Max. boom length (m) at 0°
T
TMS760E - S/N 30