You are on page 1of 3

WARNER SELF PRIMING PUMP

P Series- P50/P80

Design Features

•► Self Priming
•► Handle Liquids
•► Corrosive waste water resistant

Application

•► Warner SP 50/80 are used when one or more following are required : self priming ,
solid handlings , resistance to abrasion .Warner SP Pumps can handle liquids up
to a viscosity of about 50mm²/s (cSt)

•► Industry : transfer of neutral , acid or alkali clean or dirty liquids , liquids containing
sand , mud or solids in suspension , low viscosity petroluem products , clean or dirty
solvents , milk lime , caustic soda , washing , cooling , circulation , smoke scrubbing
emergency duty .Cibil enginnering : Sewege pumping and fire fighting.

•► Waste Water : pumping polutted , hot or corrosive wasterwater containing sand , mud
or solids in suspension , dosing neutralizing liquids , pumping out settled sludge.

Standard Material

•► Cast Iron Construction : Complete Cast Iron pump , Ductile Iron Impeller ,Cast Iron
wear plate ( optional with Rubber Plate ) and Mild steel shaft with protection sleeve ;
Nitrite Rubber gaskets , Silicon Carbide Mechanical Seal
•► Other Options : Stainless Steel and Bronze wetted parts . CB ,CS , SS , BB

•► Mechanical Seal : Silicon Carbite Vs Silicon Carbite /Viton .Other options available.
Working Principle

•► The main components of Warner SP Series Self Priming Pump are : Body , Back
Casing , Impeller , Wear Plate ,Shaft , Bearing Housing & Stuffing Box

•► The Impeller Design is ' semi -open " type with back vane which helps in balancing the
front " Axial Thrust ".

•► The Shaft Sealing is by a Mechanical Seal in Silicone or Tungsten Carbide . The shaft
is supported by 2 Heavy Duty Grease Lubricated Anti-Friction Ball bearings to counter
the Axial and radial Forces.

•► The Clearence between Impeller and Wear Plate is less than 0.5mm ; so when there
is wear , the Wear Plate could be adjusted closer to Impeller thus maximizing the
efficiency and achieving a better performance again.

•► The pump Suction Port is fitted with a "non return flap valve" , which has the function
of maintaining the pump casing and suction line filled of liquid when the pump is not
in operation , this will help the pump in priming faster soon as operated .

•► The Pump Casing must be totally filled manually at the first start only.Operating the
pump , the impeller must rotate creating an emulsion of liquid and air , the air will be
then evacuated from the suction line through the discharge line priming the pump.

Air ( white arrows) is drawn into the pump by the vacumm


produced as the impeller rotates and is emulsioned with
the liquid (blue arrows) contained in the pump casing .The
air/liquid mixture is driven into the priming chamber where
the air , which is less dense , separates out and vents
through the delivery line while the liquid , due to the higher
density , falls back and is recruited .When all the air has been
evacuated from the suction line , the pump primes and
operates like normal centrifugal pumps. It can also handle
a mixture of air and liquid . The check valve mounted in the
pump suction port serves two purpose : it prevent the liquid
from draining out of the suction line when the pump is not
in operation , and if the suction line is drained by accident ,
enough liquid is retained in the pump casing for the pump
to reprime.The delivery line must allow the air drawn from
the suction line to vent to atmosphere.
- ./
 01/
!"#!2$3B5267
%&'$()8 1097
*#"+) :02;2<=:912<:>?=1@2A
,"+

1234526789

0

12345
89573








 
00 267 
2
8 



- ./01/23452678 1097:02;2<=:912<:>?=1@2A

0
01234526789



012345
89573

5959099 
95 7925





 
00 267 
2
8 



CCCDC./01/?>8 ?DE:8 22222222222222218 .7=2F270G:H C./01/?>8 ?DE:8

You might also like