Professional Documents
Culture Documents
PREFACE
CONTENTS
Introduction Core drilling FEIN system competence Highlights FEIN core drilling units Safety QuickIN system 4 5 6 8 9
FEIN core drilling units FEIN core drilling range FEIN KBM 32 Q FEIN KBM 50 QX FEIN KBM 52 U FEIN KBM 80 U FEIN KBM 80 auto 11 12 13 14 16 17
FEIN core bits and accessories Carbide or HSS? Carbide core bits HSS core bits Centring pins, adapters, drive arbors Thread cutting accessories KBM 80 accessories Clamping fixtures Cooling and lubricating 24 25 26 27 19 20 22 23
Useful information Thread cutting Countersinking Reaming TCT/ HSS speed Tool dimension sheet Technical data Service 30 32 33 34 35 36 37
CORE DRILLING
Cross-section
View from above Centring, predrilling, finish drilling a FEIN core bit combines all of these steps
Unlike twist drilling, core drilling only involves machining a narrow ring and not the entire drilling surface, which requires much less feed force. This means that the core drilling unit consumes less power, putting less pressure on the user, core bit and the tool. The combined centring and ejector pin automatically ejects the drill core once you have broken through the material. You can core
bit a diameter of up to 80 mm in material up to 50 mm thick in just one step. You can also drill overlapping holes, for slots, for example, and offset holes. All of this makes core drilling an extremely costeffective drilling process its faster, more precise and saves more energy than twist drilling.
The FEIN clamping fixtures, which are available as accessories, allow for efficient and cost-effective working even when drilling pipes, in nonmagnetic materials or on a structured base.
Faster working in all materials With a cutting speed of up to 45 m / min, FEIN core drilling units* allow for fast work progress and high levels of cost-effectiveness in virtually all materials.
A multitude of applications in one system FEIN core drilling units are extremely versatile. The tool holder on the tools enables the use of various pieces of equipment for drilling, thread cutting, reaming and countersinking.
Not just for core drilling but for all common areas of application
90
Core drilling
80
Core drilling, twist drilling, thread cutting, countersinking, reaming FEIN core drilling units cover all common areas of application.
Countersinking
60
Countersinking
50 Core drilling
Countersinking
Twist drilling
Twist drilling
Twist drilling
Thread cutting
Reaming
Thread cutting
Thread cutting
Twist drilling
Twist drilling
30
20
10
Thread cutting
Reaming
Reaming
Reaming
40
HIGHLIGHTS
There are a number of good reasons to use core drilling units. Ours last a lifetime.
From the KBM 32 Q to the KBM 80 auto, FEIN core drilling units keep their promises for a lifetime. Their robustness and reliability also stand the test of time, as do their simple handling, high levels of safety and cost-effective use that deliver outstanding results. Core drilling units from FEIN provide you with everything you need to core bit on the construction site or in the workshop. An extensive range of accessories specially coordinated to the FEIN core drilling units ensure that you always get the right solution for drilling, thread cutting, and of course countersinking and reaming.
FEIN durability FEIN core drilling units are designed to stand up to the toughest continual use in industry and manual trades. To meet these requirements, they have a few special design features: a drill motor in a barrel-type motor housing, the transmission housing and drill jig are made from robust metal and last but not least, a high-power motor designed for a long service life and maximum performance.
Outstanding operation FEIN core drilling units are easy to operate thanks to the new "Viseo touch pad" operating concept, for example. The FEIN QuickIN quick change system allows you to change tools in a flash without having to use a wrench or adjust the drill position. The stroke range can easily be increased for large drilling tools.
High magnetic holding force The tool needs to be secure such that you can convert all of its power into work efficiency. In FEIN core drilling units, the already high magnetic holding force of the electromagnets is automatically increased when drilling is started. This ensures that the drill jig remains secure even when the drill shaft is experiencing high torque levels.
Optimum power-to-weight ratio FEIN core drilling units are extremely light and are therefore extremely well suited to on-site installation work. But their optimum power-to-weight ratio will also be appreciated when used as a workshop tool, and results from their compact design, aluminium components for drill jigs, dove-tail guide, transmission housing and compact high-power motor.
HIGHLIGHTS
Safe handling
The separate positions of the drill switch and the magnetic switch make the tool particularly easy to handle and considerably reduce the risk of incorrect operation.
Mechanical transmission
The mechanical transmission with perfectly coordinated speed levels allows for an optimum cutting speed. Its high level of efficiency ensures that the motor power is transferred to the core bit with virtually no loss.
Compact design
Their compact design and optimum power-to-weight ratio make FEIN core drilling units the ideal tool for mobile twist drilling, thread cutting, countersinking and reaming.
SAFETY
Distance between magnet and assembly surface (workpiece) Magnetic holding force
100 %
The core drilling unit must be secure if you are to core bit successfully. This can only be achieved if the magnetic foot is placed on an even and clean workpiece that is at least 12 mm thick. If this is not the case, you risk losing a considerable amount of the magnetic holding force.
KBM 80 auto
KBM 50 QX
KBM 65 Q KBM 65 QF
KBM 32 Q
KBM 80 U
KBM 52 U
Operator
Prevents the tool from starting up independently and unexpectedly if power is suddenly restored. The electronic magnetic holding force is increased when drilling starts for even better operational safety. Sufficient response time to adjust to the core drilling unit. The operator wont be surprised by the machine starting at full power. Reduced voltage when the drill motor is inactive prevents the coils from overheating. Drill motor is protected from current peaks when switching on. No damage due to overloading and overheating. Unit can be restarted immediately. Indicates whether the magnetic holding force is sufficient. Stops the drill motor if the core drilling unit is tipped. The magnetic foot cannot be deactivated accidentally. If the drill motor is active: press once: motor off /press twice: magnet off. No direct contact with moving machine parts. Operator only uses the control function. Belt prevents the machine from falling down if the power is cut accidentally. Reduced risk of incorrect operation thanks to switches in separate locations. No accidental contact with rotating machine parts. The MT tool holder cannot be removed from the spindle if the load is too high. Prevents the core drilling unit from breaking away from the work surface. Control can always be seen, as it is located on the top of the drill motor. Minimises the risk of incorrect operation. Plastic case allows the tool to be stored and transported safely. Accessories are stored safely in a separate compartment in the case. Protects the drive spindle during overload. Cutting teeth are not subject to shock and impact loads. Lower bit wear thanks to constant spindle feed force. The core drilling unit is not damaged if the tool falls from a steel girder.
Soft start
Electronic overload protection Visual magnetic holding force display Tilt sensor Locked magnetic switch when the drill motor is active Automatic drill feed Tension belt Drill switch and magnetic switch in separate positions Contact guard MT shank secured with retainer nut Torque slipping clutch
Storage case
QUICKIN SYSTEM
Perfect for fast tool changes the FEIN QuickIN system for all holders
KBM 32 Q
KBM 50 QX
KBM 52 U
KBM 65 Q KBM 65 QF
KBM 80 U
KBM 80 auto
QuickIN
"
B 16
M 18 x 6
KBM 32 Q KBM 50 Q X
KBM 52 U
KBM 65 Q KBM 65 QF
Cuts working time significantly Changing the core bit FEIN QuickIN: Weldon holder: 57 sec. 2030 sec.
In a direct comparison, the FEIN QuickIN system shows how fast and user-friendly core bit changes can now be.
Introduction Core drilling FEIN system competence Highlights FEIN core drilling units Safety QuickIN system 4 5 6 8 9
FEIN core drilling units FEIN core drilling range 11 FEIN KBM 32 Q FEIN KBM 50 QX FEIN KBM 52 U FEIN KBM 65 Q / KBM 65 QF FEIN KBM 80 U FEIN KBM 80 auto 12 13 14 15 16 17
FEIN core bits and accessories Carbide or HSS? Carbide core bits HSS core bits Centring pins, adapters, drive arbors Thread cutting accessories KBM 80 accessories Clamping fixtures Cooling and lubricating 24 25 26 27 19 20 22 23
Useful information Thread cutting Countersinking Reaming TCT/ HSS speed Tool dimension sheet Technical data Service 30 32 33 34 35 36 37
10
KBM 32 Q Compact core drilling unit with high mobility for installation jobs
KBM 50 QX Core drilling unit with two-speed transmission for efficient on-site drilling. Page 13
KBM 65 Q / KBM 65 QF Powerful core drilling unit with twospeed transmission for the workshop Page 15
KBM 80 U Universal core drilling unit with outstanding power for the workshop
KBM 80 auto Fully-automatic core drilling unit for outstanding efficiency in the workshop Page 17 KBM 80 auto
Page 12
Page 14
KBM 32 Q
Core drilling in metal with a of up to 32 mm Core drilling in metal with a of up to 50 mm Core drilling in metal with a of up to 65 mm Core drilling in metal with a of up to 80 mm
KBM 50 QX
KBM 52 U
KBM 80 U
Twist drilling with drill chuck (DIN 338) Twist drilling with MT holder (DIN 345) Thread cutting Countersinking Reaming Fully-automatic drilling Working with one hand Working overhead Installation work Workshop jobs well suited very well suited
KBM 32 Q Compact core drilling unit with high mobility for installation jobs.
The KBM 32 Q allows you to core bit with a diameter of between 12 and 32 mm. Thanks to its compact dimensions and low weight of just 10.5 kg, the KBM 32 Q is ideally suited to on-site installation work. It is easy to attach to the workpiece and enables reliable working throughout the entire process even if youre working vertically or overhead. In addition to its high mobility, the tool is characterised by extreme precision and ease of handling.
FEIN benefits Small, extremely light core drilling unit with excellent handling for vertical and overhead use QuickIN system for fast tool changes without a wrench Continuously variable double dove-tail guide enables use of long drilling tools without the tool having to be removed from the workpiece High-torque high-power motor Powerful electromagnet Electronic magnetic holding force Integrated cooling lubricant unit Electronic overload protection Restart lock
Technical data
Model Core bit max.
Core bit, max. drilling depth
KBM 32 Q mm mm mm M W W rpm rpm mm mm N mm m kg 32 50 13 12 700 450 550 440 QuickIN 135 260 9 000 160 80 4 10,5 7 270 27
Twist drill max. Thread cutting max. Power / consumption Power / output Idling speed Load speed Core bit holder Stroke Total stroke range Magnetic holding force Magnetic foot dimensions Cable with plug Weight according to EPTA Order number
Applications
Core drilling
Included in price: 1 case; 1 cooling lubricant pump; 1 tension belt; 1 swarf hook; 1 key-type drill chuck with of up to 13 mm; 1 QuickIN adapter for M 18 x 6 P 1.5; 2 centring pins; 1 contact guard
12
KBM 50 QX Core drilling unit with two-speed transmission for efficient on-site drilling.
The KBM 50 QX covers an extended area of application. Its mechanical two-speed transmission supplies enough torque to core bit with diameters of up to 50 mm. Two electronic speed levels enable reaming and countersinking and also provide a drilling function for hard materials. The KBM 50 QX is one of the lightest tools in its segment and can therefore be used vertically and overhead with ease.
FEIN benefits Mechanical two-speed transmission with two electronic speed levels enables expanded range of applications and uses such as reaming and countersinking QuickIN system for fast tool changes without a wrench Continuously variable double dove-tail guide enables use of long drilling tools without the tool having to be removed from the workpiece
Technical data
Model Core bit max. Twist drill max. Thread cutting max. Countersinking max. Reaming max. Power / consumption Power / output Load speed First gear slow First gear fast Second gear slow Second gear fast Core bit holder Stroke Total stroke range Magnetic holding force Magnetic foot dimensions Cable with plug Weight according to EPTA Order number mm mm N mm m kg rpm rpm rpm rpm 160 260 320 520 QuickIN 135 310 11 000 180 90 4 12.8 7 270 33 mm mm M mm mm W W Core bit, max. drilling depth mm KBM 50 QX 50 50 16 16 31 16 1 200 680
Compact design and optimum power-to-weight ratio High-torque high-power motor Speed-controlled tacho electronics Powerful electromagnet
Electronic magnetic holding force Integrated cooling lubricant unit Electronic overload protection Restart lock
Applications
Core drilling
Thread cutting with thread cutting tool Included in price: 1 case; 1 cooling lubricant pump; 1 tension belt; 1 swarf hook; 1 key-type drill chuck with of up to 13 mm; 1 QuickIN adapter for M 18 6 P 1.5; 2 centring pins; 1 contact guard
Countersinking
Reaming 13
FEIN benefits Mechanical two-speed transmission and continuously variable electronic speed reduction enables an optimum cutting speed for drilling, thread cutting, reaming and countersinking Flexible tool use and high concentricity thanks to a combination of QuickIN and MT 3 holders Continuously variable double dove-tail guide enables use of long drilling tools without the tool having to be removed from the workpiece Compact design and optimum powerto-weight ratio Clockwise/anti-clockwise rotation High-torque high-power motor Speed-controlled tacho electronics Powerful electromagnet Electronic magnetic holding force Speed-saving memory function Integrated gravity-fed cooling lubricant unit Easy to use with one hand Electronic overload protection Restart lock
Technical data
Model Core bit max. Core bit, max. drilling depth Twist drill max. Thread cutting max. Countersinking max. Reaming max. Power / consumption Power / output Load speed First gear Second gear Core bit holder Tool holder Stroke Total stroke range Magnetic holding force Magnetic foot dimensions Cable with plug Weight according to EPTA Order number MT mm mm N mm m kg rpm rpm 130 260 260 520 QuickIN 3 135 310 11 000 180 90 4 14.2 7 270 31 mm mm mm M mm mm W W KBM 52 U 50 50 23 16 50 23 1 200 640
Applications
Core drilling
Included in price: 1 case; 1 coolant tank; 1 tension belt; 1 swarf hook; 1 key-type drill chuck with of up to 13 mm; 1 QuickIN adapter for M 18 6 P 1.5; 2 centring pins; 1 drift key; 1 contact guard Wide range of accessories: from page 20 Tool dimension sheet: page 35
Countersinking
Reaming
KBM 65 Q / KBM 65 QF Powerful core drilling unit with two-speed transmission for the workshop.
The robust and powerful FEIN two-speed tools KBM 65 Q and KBM 65 QF are perfect introductions to the class of workshop tools. Both tools provide an ideal speed for heavy-duty use with a core bit diameter of up to 65 mm. Thanks to their extremely large stroke range, they are the ideal solution for special applications such as deep drilling or thread cutting. The tool spindle on the tools enables flexible use of MT 3 tools with high concentricity. The KBM 65 QF can also be finely adjusted, guaranteeing outstanding results.
FEIN benefits Powerful even in tough applications such as core drilling with a of up to 65 mm or thread cutting up to M 20 Flexible tool use and high concentricity thanks to a combination of QuickIN and MT 3 holders Continuously variable double dove-tail guide enables use of long drilling tools without the tool having to be removed from the workpiece KBM 65 QF: Fine adjustment of drill spindle for easy alignment of tool without the time-consuming task of removing and refitting the magnet Optimum power-to-weight ratio Mechanical two-speed transmission 2 electronic speed levels per gear Speed-controlled tacho electronics Powerful electromagnet Integrated cooling lubricant unit Electronic overload protection Restart lock
Technical data
Model Core bit max. Twist drill max. Thread cutting max. Countersinking max. Reaming max. Power / consumption Power / output Load speed First gear slow First gear fast Second gear slow Second gear fast Core bit holder Tool holder Stroke Total stroke range Swivel range for drill jigs Magnetic holding force Magnetic foot dimensions Cable with plug Weight according to EPTA Order number MT mm mm mm N mm m kg 12 000 184 92 4 19.0 7 270 29 rpm rpm rpm rpm 125 250 255 510 QuickIN 3 145 330 125 250 255 510 QuickIN 3 145 330 6 8 12 000 184 92 4 20.6 7 270 28 mm mm M mm mm W W Core bit, max. drilling depth mm KBM 65 Q KBM 65 QF 65 50 23 20 50 23 1 460 650 65 50 23 20 50 23 1 460 650
Core drilling
Included in price: 1 case; 1 cooling lubricant pump; 1 tension belt; 1 swarf hook; 1 key-type drill chuck with of up to 13 mm;1 QuickIN adapter for M 18 x 6 P 1.5; 2 centring pins; 1 drift key; 1 contact guard Wide range of accessories: from page 20 Tool dimension sheet: page 35 15
Countersinking
Reaming
KBM 80 U Universal core drilling unit with outstanding power for the workshop.
The KBM 80 U workshop tool is the ideal tool for those wanting to use a core drilling unit for the entire range of applications: core drilling, drilling, thread cutting, countersinking and reaming. The KBM 80 U combines everything you need to work professionally: a 2000 watt high-power motor with a powerful three-speed transmission, clockwise / anti-clockwise rotation, an MT 3 holder, electric speed reduction and a memory function to save the speed for serial drilling work.
FEIN benefits Mechanical three-speed transmission with continuously variable electronic speed reduction enables an optimum cutting speed for core drilling, drilling, thread cutting, countersinking and reaming. Flexible tool use and high concentricity thanks to a combination of QuickIN and MT 3 holders High-torque, high-power motor for efficient core drilling up to 80 mm and thread cuts up to M 27 QuickIN MAX quick change system Extra large stroke range Clockwise/anti-clockwise rotation Speed-controlled tacho electronics Powerful electromagnet Electronic magnetic holding force Visual magnetic holding force display Fine adjustment of drill spindle Automatic coolant supply Torque slipping clutch Viseo touch pad control Speed-saving memory function Electronic overload protection
Technical data
Model TCT core bit max. HSS core bit max. Twist drill max. Thread cutting max. Countersinking max. Reaming max. Power / consumption Power / output Load speed First gear Second gear Third gear Core bit holder Tool holder Stroke Total stroke range Swivel range for drill jigs Magnetic holding force Magnetic foot dimensions Cable with plug Weight according to EPTA Order number N mm m kg MT mm mm rpm rpm rpm 110 180 160 260 350 580 QuickIN / QuickIN MAX 3 145 285 4,25 11 18 000 270 90 4 25,4 7 270 34 mm mm mm M mm mm W W KBM 80 U 80 65 50 32 27 50 31 2 000 900
Applications
Core drilling
Included in price: 1 case; 1 coolant tank; 1 tension belt; 1 swarf hook, 1 key-type drill chuck with of up to 13 mm; 1 QuickIN adapter for M 18 x 6 P 1.5; 2 centring pins; 1 drift key; 1 contact guard Wide range of accessories: from page 20 QuickIN MAX accessories: page 25 Tool dimension sheet: page 35
Countersinking
Reaming
KBM 80 auto Fully-automatic core drilling unit for outstanding efficiency in the workshop.
The KBM 80 auto workshop tool sets new standards for core drilling diameters up to 80 mm in terms of productivity, flexibility and operational safety. Its automatic drill feed enables reproducible drilling times and constant work progress in all materials. It saves a lot of time and money, particularly for large drilling jobs. The KBM 80 auto also considerably increases operational safety, as you dont have to intervene in the drilling process. As the first fully-automatic core drilling unit with a digitallycontrolled drill feed, the KBM 80 auto ensures levels of efficiency never seen before in the workshop.
FEIN benefits Saves time and money when working on large drilling jobs as the digitally-controlled drill feed ensures constant work progress in all materials with low tool wear Thanks to reproducible and timed drilling times, working hours for commissioned and serial work can be planned High levels of operational safety thanks to extensive safety package including torque slipping clutch, visual magnetic holding force display and Viseo touch pad control
Technical data
Model TCT core bit max. HSS core bit max. Twist drill max. Thread cutting max. Countersinking max. Reaming max. Power / consumption Power / output Load speed First gear Second gear Third gear Core bit holder Tool holder Stroke Total stroke range Swivel range for drill jigs Magnetic holding force Magnetic foot dimensions Cable with plug Weight according to EPTA Order number N mm m kg MT mm mm rpm rpm rpm 110 180 160 260 350 580 QuickIN / QuickIN MAX 3 145 285 4.25 11 18 000 270 90 4 26.4 7 270 32 mm mm mm M mm mm W W KBM 80 auto 80 65 50 32 27 50 31 2 000 900
High-torque high-power motor MT 3 holder QuickIN MAX quick change system QuickIN quick change system Extra large stroke range Clockwise/anti-clockwise rotation Speed-controlled tacho electronics Applications
Powerful electromagnet Electronic magnetic holding force Fine adjustment of drill spindle Automatic coolant supply Speed-saving memory function Electronic overload protection
Core drilling
Included in price: 1 case; 1 coolant tank; 1 tension belt; 1 swarf hook, 1 key-type drill chuck with of up to 13 mm; 1 QuickIN adapter for M 18 x 6 P 1.5; 2 centring pins; 1 drift key; 1 contact guard Wide range of accessories: from page 20 QuickIN MAX accessories: page 25 Tool dimension sheet: page 35
Countersinking
Reaming
17
Introduction Core drilling FEIN system competence Highlights FEIN core drilling units Safety QuickIN system 4 5 6 8 9
FEIN core drilling units FEIN core drilling range FEIN KBM 32 Q FEIN KBM 50 QX FEIN KBM 52 U FEIN KBM 80 U FEIN KBM 80 auto 11 12 13 14 16 17
FEIN core bits and accessories Carbide or HSS? Carbide core bits HSS core bits drive arbors Thread cutting accessories KBM 80 accessories Clamping fixtures Cooling and lubricating 24 25 26 27 19 20 22
Useful information Thread cutting Countersinking Reaming TCT/ HSS speed Tool dimension sheet Technical data Service 30 32 33 34 35 36 37
CARBIDE OR HSS?
FEIN tCt S
Special core bit, extremely tough for use in track and rail construction. See page 21
Material Alu < 10 % Si < 600 N/mm2 Alu > 10 % Si < 600 N/mm Steel < 500 N/mm
2 2
Steel < 750 N/mm2 Steel < 900 N N/mm2 Steel < 1100 N/mm2 Steel < 1400 N/mm
2
Stainless steel < 700 N N/mm Stainless steel > 700 N/mm
2
ideal
Cast iron (grey cast iron, globular cast iron) < 300 N/mm2 Brass (CuZn) < 500 N/mm2 Hard-to-cut materials Rails Surface Flat surfaces Structured surfaces Pipe surface Round surfaces Offset surfaces Special application Dry drilling Stepped drilling Multi-layer drilling Overlapping drilling
well suited very well suited
19
CORE BITS
Number of drill holes Test conditions: While carbide products from other manufacturers achieved an average result of 190 holes per core bit, the FEIN TCT ulTra created 380 holes. Material: C 45 steel, 30 mm thick; : 18 mm
TCT Ultra core bit with QuickIN holder Very long service life and outstanding cutting performance. Metric dimensions, cutting depth 35 mm
mm 33 34 35 36 37 38 39
Order number No. in pack 1 6 31 27 107 01 0 6 31 27 108 01 8 6 31 27 109 01 2 6 31 27 110 01 4 6 31 27 111 01 3 6 31 27 112 01 6 6 31 27 113 01 0 6 31 27 114 01 8 6 31 27 115 01 2 6 31 27 116 01 5 6 31 27 117 01 9 6 31 27 118 01 7 6 31 27 119 01 1 6 31 27 120 01 3 6 31 27 121 01 2 6 31 27 122 01 5 6 31 27 123 01 9 6 31 27 124 01 7 6 31 27 125 01 1 6 31 27 126 01 4 6 31 27 127 01 8 6 31 27 128 01 6 6 31 27 129 01 0 6 31 27 130 01 2 6 31 27 131 01 1 6 31 27 132 01 4 6 31 27 133 01 8 6 31 27 134 01 6 6 31 27 135 01 0 6 31 27 136 01 3 6 31 27 137 01 7 6 31 27 138 01 5 6 31 27 139 01 9
Multi-packs Use our multi-packs and enjoy savings. All promotional packs come with between 1 and 3 free core bits!
19 20 21 22 23 Order number No. in pack 4 6 31 27 086 02 0 6 31 27 087 02 0 6 31 27 088 04 0 6 31 27 089 02 0 6 31 27 090 02 0 6 31 27 091 02 0 6 31 27 092 03 0 6 31 27 093 02 0 6 31 27 094 02 0 6 31 27 095 02 0 6 31 27 096 02 0 6 31 27 097 02 0 6 31 27 098 02 0 6 31 27 099 02 0 6 31 27 100 02 0 6 31 27 101 02 0 6 31 27 102 02 0 6 31 27 103 02 0 6 31 27 104 02 0 6 31 27 105 02 0 6 31 27 106 02 0 Set 24 25 26 27 28 29 30 31 32
6 31 27 093 03 0 6 31 27 094 03 0 6 31 27 095 03 0 6 31 27 096 03 0 6 31 27 097 03 0 6 31 27 098 03 0 6 31 27 099 03 0 6 31 27 100 03 0 6 31 27 101 03 0 6 31 27 102 03 0 6 31 27 103 03 0 6 31 27 104 03 0 6 31 27 105 03 0 6 31 27 106 03 0
mm 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
3+1
Order number No. in pack 1 6 31 27 086 01 9 6 31 27 087 01 3 6 31 27 088 01 1 6 31 27 089 01 5 6 31 27 238 01 1 6 31 27 090 01 7 6 31 27 091 01 6 6 31 27 239 01 5 6 31 27 092 01 9 6 31 27 093 01 3 6 31 27 240 01 7 6 31 27 094 01 1 6 31 27 095 01 5 6 31 27 096 01 8 6 31 27 097 01 2 6 31 27 098 01 0 6 31 27 099 01 4 6 31 27 100 01 5 6 31 27 241 01 6 6 31 27 101 01 4 6 31 27 102 01 7 6 31 27 103 01 1 6 31 27 104 01 9 6 31 27 105 01 3 6 31 27 106 01 6
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
Consists of 4 core bits with a of 14, 18, 22 and 32 mm (cutting depth 35 mm) and 1 centring pin (105 mm) in a plastic carry case Order number 6 31 27 088 03 0
TCT Ultra 2" core bit with QuickIN holder Very long service life and outstanding cutting performance. Imperial dimensions, cutting depth 2" / 50 mm
mm 12 13 14 15 16 17 18
7+3
Order number No. in pack 10 6 31 27 086 03 0 6 31 27 087 03 0 6 31 27 088 05 0 6 31 27 089 03 0 6 31 27 090 03 0 6 31 27 091 03 0 6 31 27 092 04 0 in " " " " " mm 12.70 14.29 15.88 17.46 19.05 Order number No. in pack 1 6 31 27 383 01 0 6 31 27 384 01 0 6 31 27 385 01 0 6 31 27 386 01 0 6 31 27 387 01 0
20
CORE BITS
" " " 1" 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 2" 2 "
20.64 22.23 23.81 25.40 26.99 28.58 30.16 31.75 33.34 34.93 36.51 38.10 39.19 41.28 42,86 44.45 46.04 47.63 49.21 50.80 52.39
6 31 27 388 01 0 6 31 27 389 01 0 6 31 27 390 01 0 6 31 27 391 01 0 6 31 27 392 01 0 6 31 27 393 01 0 6 31 27 394 01 0 6 31 27 395 01 0 6 31 27 396 01 0 6 31 27 397 01 0 6 31 27 398 01 0 6 31 27 399 01 0 6 31 27 400 01 0 6 31 27 401 01 0 6 31 27 402 01 0 6 31 27 403 01 0 6 31 27 404 01 0 6 31 27 405 01 0 6 31 27 406 01 0 6 31 27 407 01 0 6 31 27 408 01 0
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
6 31 27 021 01 3 6 31 27 022 01 6 6 31 27 004 01 0 6 31 27 005 01 4 6 31 27 023 01 0 6 31 27 006 01 7 6 31 27 024 01 8 6 31 27 007 01 1 6 31 27 025 01 2 6 31 27 008 01 9 6 31 27 026 01 5 6 31 27 009 01 3 6 31 27 010 01 5 6 31 27 027 01 9 6 31 27 028 01 7 6 31 27 011 01 4 6 31 27 029 01 1 6 31 27 012 01 7 6 31 27 030 01 3 6 31 27 013 01 1 6 31 27 014 01 9 6 31 27 031 01 2 6 31 27 015 01 3 6 31 27 032 01 5 6 31 27 033 01 9 6 31 27 016 01 6 6 31 27 034 01 7 6 31 27 017 01 0 6 31 27 035 01 1 6 31 27 018 01 8 6 31 27 036 01 4 6 31 27 037 01 8 6 31 27 038 01 6 6 31 27 039 01 0 6 31 27 040 01 2 6 31 27 041 01 1 6 31 27 049 01 9 6 31 27 050 01 1 6 31 27 051 01 0 6 31 27 052 01 3 6 31 27 053 01 7 6 31 27 054 01 5 6 31 27 055 01 9
TCT S core bit with FEIN thread M 18 x 6 P 1.5 Specially developed for use in track and rail construction. Extremely hard cutting teeth and an optimum cutting geometry ensure the best results. Metric dimensions, cutting depth 50 mm
36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
6 31 27 300 01 0 6 31 27 301 01 0 6 31 27 302 01 0 6 31 27 303 01 0 6 31 27 304 01 0 6 31 27 305 01 0 6 31 27 306 01 0 6 31 27 307 01 0 6 31 27 308 01 0 6 31 27 309 01 0 6 31 27 310 01 0 6 31 27 311 01 0 6 31 27 312 01 0 6 31 27 313 01 0 6 31 27 314 01 0 6 31 27 315 01 0 6 31 27 316 01 0 6 31 27 317 01 0 6 31 27 318 01 0 6 31 27 319 01 0 6 31 27 320 01 0 6 31 27 321 01 0 6 31 27 322 01 0 6 31 27 323 01 0 6 31 27 324 01 0 6 31 27 325 01 0 6 31 27 326 01 0 6 31 27 327 01 0 6 31 27 328 01 0 6 31 27 329 01 0
mm 24 26 30 32 33 36 40
Order number No. in pack 1 6 31 27 056 01 2 6 31 27 057 01 6 6 31 27 058 01 4 6 31 27 059 01 8 6 31 27 048 01 5 6 31 27 060 01 0 6 31 27 436 01 0
TCT Ultra 50 core bit with Weldon holder Very long service life and outstanding cutting performance. Metric dimensions, cutting depth 50 mm
Set Consists of 4 core bits with a of ", ", ", " (cutting depth 2"/50 mm) and 1 centring pin (105 mm) in a plastic carry case Order number 6 31 27 384 02 0
45 46 47 48 49 50
mm 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Order number No. in pack 1 6 31 27 276 01 0 6 31 27 277 01 0 6 31 27 278 01 0 6 31 27 279 01 0 6 31 27 280 01 0 6 31 27 281 01 0 6 31 27 282 01 0 6 31 27 283 01 0 6 31 27 284 01 0 6 31 27 285 01 0 6 31 27 286 01 0 6 31 27 287 01 0 6 31 27 288 01 0 6 31 27 289 01 0 6 31 27 290 01 0 6 31 27 291 01 0 6 31 27 292 01 0 6 31 27 293 01 0 6 31 27 294 01 0 6 31 27 295 01 0 6 31 27 296 01 0 6 31 27 297 01 0 6 31 27 298 01 0 6 31 27 299 01 0
61 62 63 64 65
TCT Ultra 50 core bit with FEIN thread M 18 x 6 P 1.5 Very long service life and outstanding cutting performance. Metric dimensions, cutting depth 50 mm
51 52 53 54 55 56 57 58 59
mm 12 13 14 15 16 17 18 19 20 21 22
Order number No. in pack 1 6 31 27 042 01 4 6 31 27 043 01 8 6 31 27 044 01 6 6 31 27 045 01 0 6 31 27 046 01 3 6 31 27 047 01 7 6 31 27 001 01 5 6 31 27 019 01 2 6 31 27 002 01 8 6 31 27 020 01 4 6 31 27 003 01 2
60 61 62 63 64 65
33 34 35
21
CORE BITS
HSS PrIMa core bit with QuickIN holder 5% cobalt alloy for long service lives. Metric dimensions, cutting depth 35 mm
Multi-packs Use our multi-packs and enjoy savings. Buy 7 drills, get 1 free! mm 12 13 14
HSS PrIMa 1" core bit with QuickIN holder 5 % cobalt alloy for long service lives, imperial dimensions, cutting depth 1" / 25 mm
Set Consists of 4 core bits with a of ", ", ", " (cutting depth 1"/25 mm) and 1 centring pin in a plastic carry case
7+1
Order number No. in pack 8 6 31 27 194 02 0 6 31 27 195 02 0 6 31 27 196 02 0 6 31 27 197 02 0 6 31 27 198 02 0 6 31 27 199 02 0 6 31 27 200 02 0 6 31 27 201 02 0 6 31 27 202 02 0 6 31 27 203 02 0 6 31 27 204 02 0 6 31 27 205 02 0 6 31 27 206 02 0 6 31 27 207 02 0 6 31 27 208 02 0 6 31 27 209 02 0 6 31 27 210 02 0 6 31 27 211 02 0 6 31 27 212 02 0 6 31 27 213 02 0 6 31 27 214 02 0 in " " " " " " " " " 1" 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 1 " 2 2 " mm 11.11 12.70 14.29 15.88 17.46 19.05 23.81 22.23 23.81 25.40 26.99 28.58 30.16 31.75 33.34 34.93 36.51 38.10 39.19 41.28 42.86 44.45 48.04 47.63 49.21 50.80 52.39 Order number No. in pack 1 6 31 27 409 01 0 6 31 27 410 01 0 6 31 27 411 01 0 6 31 27 412 01 0 6 31 27 413 01 0 6 31 27 414 01 0 6 31 27 415 01 0 6 31 27 416 01 0 6 31 27 417 01 0 6 31 27 418 01 0 6 31 27 419 01 0 6 31 27 420 01 0 6 31 27 421 01 0 6 31 27 422 01 0 6 31 27 423 01 0 6 31 27 424 01 0 6 31 27 425 01 0 6 31 27 426 01 0 6 31 27 427 01 0 6 31 27 428 01 0 6 31 27 429 01 0 6 31 27 430 01 0 6 31 27 431 01 0 6 31 27 432 01 0 6 31 27 433 01 0 6 31 27 434 01 0 6 31 27 435 01 0
Order number
6 31 27 411 02 0
mm 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Order number No. in pack 1 6 31 27 194 01 0 6 31 27 195 01 4 6 31 27 196 01 7 6 31 27 197 01 1 6 31 27 198 01 9 6 31 27 199 01 3 6 31 27 200 01 1 6 31 27 201 01 0 6 31 27 202 01 3 6 31 27 203 01 7 6 31 27 204 01 5 6 31 27 205 01 9 6 31 27 206 01 2 6 31 27 207 01 6 6 31 27 208 01 4 6 31 27 209 01 8 6 31 27 210 01 0 6 31 27 211 01 9 6 31 27 212 01 2 6 31 27 213 01 6 6 31 27 214 01 4
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
22
CORE BITS
FEIN HSS Dura core bits are used where working conditions are permanently adverse or where coolant cannot be used. They are made from high-quality high-speed steel with a cobalt content of 5 %. The surface is covered by a first-class titanium aluminium nitrate coating. It ensures the best glide properties, increased heat resistance and outstanding service lives in steel, stainless steel and cast iron.
Centring pins Length 105 mm Core bit TCT ulTra HSS Prima HSS Dura Order number Holder QuickIN QuickIN QuickIN Cutting depth 35 mm 35 mm 35 mm
Length 3 " Core bit HSS Prima 1" 7 / 16" HSS Nova 1" 7 / 16" Order number Length 4 /" Core bit Holder Cutting depth 50 mm 50 mm 50 mm Holder Cutting depth 2" Holder QuickIN QuickIN Cutting depth 1" 1"
3 02 17 338 00 0
3 02 17 332 00 9
TCT ulTra 50 QuickIN MAX TCT ulTra 50 M 18 6 P 1,5 (with adapter 6 39 01 020 00 6) TCT ulTra 50 Weldon (with adapter 6 39 01 021 01 4)
3 02 17 337 00 2
Number of drill holes Test conditions: While HSS products from other manufacturers achieved an average result of 140 holes per core bit, the FEIN HSS D ura created 180 holes. Material: C 45 steel, 30 mm thick; : 18 mm
Competition Weldon 25, 35, 40 (with adapter 6 39 01 021 01 4) mm Competition M18 6 P 1,5 (with adapter 6 39 01 020 00 6) Order number 50 mm
The adapter 6 39 01 024 01 must be used for Weldon core bits from other manu-facturers that have an internal hole of > 6.4 mm.
3 02 17 333 00 3
HSS DUra core bit with QuickIN holder 5 % cobalt alloy and surface coating for outstanding service lives and the best glide properties. Metric dimensions, cutting depth 35 mm
Set Consists of 6 core bits with a of 14, 16, 18, 20, 22, 26 mm (cutting depth 35 mm) and centring pin in plastic carry case Order number 6 31 27 142 02 9
TCT ulTra QuickIN (with adapter 6 39 01 045 01 0) QuickIN HSS Prima (with adapter 6 39 01 045 01 0) HSS Dura QuickIN (with adapter 6 39 01 045 01 0) Competition Weldon (with adapter 6 39 01 021 01 4) Order number Length 4 " Core bit TCT ulTra 2" Holder QuickIN QuickIN Weldon
HSS Nova 1" core bit with Weldon holder Industrial standard. Imperial dimensions, cutting depth 1"/25 mm mm 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Order number No. in pack 1 6 31 27 140 01 1 6 31 27 141 01 0 6 31 27 142 01 3 6 31 27 143 01 7 6 31 27 144 01 5 6 31 27 145 01 9 6 31 27 146 01 2 6 31 27 147 01 6 6 31 27 148 01 4 6 31 27 149 01 8 6 31 27 150 01 0 6 31 27 151 01 9 6 31 27 152 01 2 6 31 27 153 01 6 6 31 27 154 01 4 6 31 27 155 01 8 6 31 27 156 01 1 6 31 27 157 01 5 6 31 27 158 01 3 6 31 27 159 01 7 6 31 27 160 01 9 in " " " " " " " " " 1" 1 " 1 " 1 " 1 " mm 11.11 12.70 14.29 15.88 17.46 19.05 20.64 22.23 23.81 25.40 26.99 28.58 30.16 31.75 Order number No. in pack 1 6 31 27 356 01 5 6 31 27 357 01 0 6 31 27 358 01 0 6 31 27 359 01 0 6 31 27 360 01 0 6 31 27 361 01 0 6 31 27 362 01 0 6 31 27 363 01 0 6 31 27 364 01 0 6 31 27 365 01 0 6 31 27 366 01 0 6 31 27 367 01 0 6 31 27 368 01 0 6 31 27 369 01 0
3 02 17 355 00 0
HSS Prima 1" HSS Nova 1" Order number Length 4 /" Core bit
3 02 17 332 00 9
Holder
TCT ulTra 2" QuickIN MAX HSS Prima 1" QuickIN (with adapter 6 39 01 045 01 0)
Competition Weldon 1", 1 3 / 8" (with adapter 6 39 01 021 01 4) Order number Length 5 /" Core bit Holder Cutting depth 2" 2" 3 02 17 333 00 3
TCT ulTra 2" QuickIN (with adapter 6 39 01 045 01 0) Competition Weldon (with adapter 6 39 01 021 01 4) Order number
3 02 17 355 00 0
23
ACCESSORIES
Extension for use on confined, deep, or layered surfaces, through holes possible from a of 36 mm. QuickIN holder, length 100 mm, incl. centring pin
Thread cutting Thread cutting quick change chuck for KBM 52 U can only be used for core drilling units with anti-clockwise rotation. Size 2, with QuickIN holder, for thread drills (DIN 374/376) in conjunction with thread cutting inserts with or without M 6 - M 16 safety clutch
Size 2 thread cutting inserts for thread drills in accordance with DIN 374/376
6 39 01 020 00 6
Thread M6 M8
mm 4,5 6 7 9 11 12 14 16
Order number 6 32 06 117 01 5 6 32 06 095 01 1 6 32 06 096 01 4 6 32 06 097 01 8 6 32 06 098 01 6 6 32 06 099 01 0 6 32 06 100 01 1 6 32 06 101 01 0
Order number
6 31 06 016 01 0
Drive arbors QuickIN drive arbors for using FEIN core bits on bench and column drilling tools and all other core drilling units with an MT holder. Incl. hand pump and centring pin for external cooling lubricant supply.
Order number
6 39 01 021 01 4
Special Weldon output. Specially designed for core bits from other manufacturers that have an internal hole of > 6.4 mm
Thread cutting tool for KBM 32 Q and KBM 50 QX Size 2, with QuickIN holder, for thread drills (DIN 374/376), in conjunction with thread cutting inserts with or without M 6 - M 16 safety clutch. Incl. torque support
6 39 01 024 01 9 Taper MT3 MT2 mm 12 65 12 35 Order number 6 39 01 019 01 3 6 39 01 018 01 9 Order number for retrofitting the KBM 52 U (7 270 31), KBM 65 Q (7 270 26) and KBM 65 QF (7 270 23) models. Integrated cooling lubricant supply 9 26 02 072 01 2 Thread M6 M8 M 10 M 12 M 14 M 16 M 18 M 20 6 39 01 017 01 1 Thread drills are available from specialist dealers Order number 9 26 02 066 01 2 KBM 80 U / 80 auto accessories see page 26 mm 4.5 6 7 9 11 12 14 16 3.4 4.9 5.5 7 9 9 11 12 Order number 6 32 06 118 01 3 6 32 06 102 01 3 6 32 06 103 01 7 6 32 06 104 01 5 6 32 06 105 01 9 6 32 06 106 01 2 6 32 06 107 01 6 6 32 06 108 01 4
6 39 01 022 00 8
Order number
Thread cutting tool for KBM 65 Q and KBM 65 QF Size 2, with MT 3 holder, for thread drills (DIN 374/376), in conjunction with thread cutting inserts with or without M 6 - M 20 safety clutch. Incl. torque support
Adapter with Weldon holder to convert other manufacturers products to the QuickIN system
Conversion kit for previous model KBM 542 to QuickIN quick change system Order number 6 39 01 027 01 0
Key-type drill chuck with QuickIN holder Clamping width mm 1.5 13 1 16 24 Order number No. in pack 1 6 39 01 023 02 0 6 39 01 023 01 1 KBM 80 U / 80 auto accessories see page 25 Order number 6 39 01 028 01 8
KBM 80 ACCESSORIES
FEIN KBM 80 QuickIN MAX accessories fits together what belongs together.
With a wide range of accessories, from core bits, centring pins and adapters to special drive arbors for various drives, FEIN ensures that everything falls into place perfectly when youre core drilling with the KBM 80. The QuickIN MAX tool holder allows TCT ulTra 50 core bits to fit to tools from other manufacturers with a Weldon 32 standard holder.
TCT Ultra 50 core bit with QuickIN MAX holder Very long service life and outstanding cutting performance. Metric dimensions, cutting depth 50 mm 78 79 80 6 31 27 458 01 0 6 31 27 459 01 0 6 31 27 460 01 0
KBm 80 u
KBM 80 auto
QuickiN MAX
QuickIN
WRE 3/2
MT3/ Weldon 32
QIM
M22M27
M6M20
TCT Ultra 2" core bit with QuickIN MAX holder Very long service life and outstanding cutting performance. Imperial dimensions, cutting depth 2"/50 mm mm 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 Order number No. in pack 1 6 31 27 330 01 0 6 31 27 331 01 0 6 31 27 332 01 0 6 31 27 333 01 0 6 31 27 334 01 0 6 31 27 335 01 0 6 31 27 336 01 0 6 31 27 337 01 0 6 31 27 338 01 0 6 31 27 339 01 0 6 31 27 340 01 0 6 31 27 341 01 0 6 31 27 342 01 0 6 31 27 343 01 0 6 31 27 344 01 0 6 31 27 345 01 0 6 31 27 346 01 0 6 31 27 347 01 0 6 31 27 348 01 0 6 31 27 349 01 0 6 31 27 350 01 0 6 31 27 351 01 0 6 31 27 352 01 0 6 31 27 353 01 0 6 31 27 354 01 0 6 31 27 355 01 0 6 31 27 456 01 0 6 31 27 457 01 0 Length in mm 125 Order number 3 02 17 333 00 3 Centring pin Centring pin for QuickIN MAX core bits in 2" 2 " 2 " 2 " 2 " 2 " 2 " 2 " 2 " 2 " 2 " 2 " 2 " 2 2 " 2 " 3" 3 " 3 " mm 50.80 52.39 53.98 55.56 57.15 58.74 60.33 61.91 63.50 65.09 66.68 68.26 69.85 71.44 73.03 74.61 76.20 77.79 79.38 Order number No. in pack 1 6 31 27 437 01 0 6 31 27 438 01 0 6 31 27 439 01 0 6 31 27 440 01 0 6 31 27 441 01 0 6 31 27 442 01 0 6 31 27 443 01 0 6 31 27 444 01 0 6 31 27 445 01 0 6 31 27 446 01 0 6 31 27 447 01 0 6 31 27 448 01 0 6 31 27 449 01 0 6 31 27 450 01 0 6 31 27 451 01 0 6 31 27 352 01 0 6 31 27 353 01 0 6 31 27 454 01 0 6 31 27 455 01 0
QuickIN MAX output For retrofitting KBM 80 U / KBM 80 auto. With integrated cooling lubricant supply. For all FEIN QuickIN MAX core bits with a of 50 80 mm
Order number
6 39 01 045 01 0
Order number
6 39 01 038 02 0
Weldon 32 standard output Specially designed for core bits with cutting surfaces offset by 90. Maximum cutting depth 50 mm
Weldon 32 output Cutting surfaces in line. Maximum cutting depth 75 mm. Specially designed for core bits from:
Clamping width in mm 1 16
MT 3 drive arbors QuickIN output For retrofitting KBM 80 U / KBM 80 auto. With integrated cooling lubricant supply. For all QuickIN core bits with a of 12 65 mm Jancy
Order number
25
ACCESSORIES
Thread cutting with the KBM 80 Thread cutting quick change chuck for KBM 80 can only be used for core drilling units with anti-clockwise rotation. Size 3, with QuickIN MAX holder, for thread drill (DIN 374 / 376), in conjunction with thread cutting inserts with or without M 22 M 27 safety clutch
Whether theyre magnetic or not, theres a FEIN clamping fixture for every purpose.
FEIN offers alternative clamping fixtures for materials and workpieces with which the core drilling units electromagnet cannot be used. These range from a suction plate for non-magnetic materials like stainless steel or aluminium and a vacuum plate for e.g. chequered metal or bulb plate, which is used in conjunction with a vacuum pump to a fixture for drilling pipes with a diameter of between 60 and 300 mm.
Clamping fixtures Order number 9 26 02 082 01 0 Vacuum plate for non-magnetic materials and structured bases (chequered metal, bulb plate etc.) Must be used in conjunction with the vacuum pump
General accessories Contact and swarf guard prevents accidental contact with rotating parts and increases passive safety. Also suited to retrofitting KBM 32 Q, 50 Q, 50 QX and KBM 52 U
Size 3 thread cutting inserts for thread drills in accordance with DIN 374/376
Thread
mm
Order number 6 32 06 119 01 0 6 32 06 120 01 0 Vacuum plate 396 x 200 x 95 mm for KBM 32 Q, 50 QX, 52 U, 65 Q, 65 QF Order number 9 26 02 057 01 7
Order number
6 39 01 037 01 0
M 22 / M 24 18 14.5 M 27 20 16
Pipe drill fixture incl. tension belt, to make holes on pipes with a pipe of between 60 and 300 mm, 220 x 130 mm
Vacuum plate 396 x 350 x 95 mm for KBM 80 U, 80 auto Order number 9 26 02 085 01 0
Thread
mm
Vacuum pump Suction rate 0.015 m3/ min, 0.8 bar, 92 watts, weight 2.5 kg, incl. suction hose
M 22 / M 24 18 14,5 M 27 20 16
Interchangeable reducing insert (WRE 3/2) Reducing insert for holding size 2 thread cutting inserts (M 6 - M 20) in size 3 quick change chuck. (9 26 02 082 01 0) Order number 9 26 01 022 01 3
Order number
9 26 02 055 01 0
Order number
6 32 06 125 01 0
26
Lubricant Emulsion, Petroleum* Emulsion, Petroleum* Emulsion Emulsion Emulsion, high-performance cutting oil Emulsion, high-performance cutting oil Emulsion, high-performance cutting oil Emulsion Emulsion, high-performance cutting oil Emulsion, dry Emulsion Emulsion, high-performance cutting oil Emulsion, high-performance cutting oil
The coolant and lubricant must be optimally matched to the material to be machined to ensure a long drilling tool service life.
Cooling Hand pump Capacity approx. 450 ml. Suited to FEIN core drilling units KBM 32 Q, KBM 50 QX, KBM 52 U, KBM 65 Q, KBM 65 QF Gravity-fed cooling lubricant unit. Capacity approx. 500 ml, precise dosing of flow rate by ball valve. Suited to FEIN core drilling units KBM 32 Q, KBM 50 QX and KBM 52 U manufactured from 2006
Order number
3 21 32 022 00 7
Order number The interior cooling lubrication of the FEIN core drilling units enables rapid, cost-effective work and a long tool service life.
6 39 01 036 01 0
27
Introduction Core drilling FEIN system competence Highlights FEIN core drilling units Safety QuickIN system 4 5 6 8 9
FEIN core drilling units FEIN core drilling range FEIN KBM 32 Q FEIN KBM 50 QX FEIN KBM 52 U FEIN KBM 80 U FEIN KBM 80 auto 11 12 13 14 16 17
FEIN core bits and accessories Carbide or HSS? Carbide core bits HSS core bits Centring pins, adapters, drive arbors Thread cutting accessories KBM 80 accessories Clamping fixtures Cooling and lubricating 24 25 26 27 19 20 22 23
Useful information Thread cutting Countersinking Reaming TCT / HSS speed Tool dimension sheet Technical data Service 30 32 33 34 35 36 37
Useful information
For more than 25 years, FEIN has been synonymous with sound specialist knowledge, extensive expertise and system competence in core drilling, not just in core drilling units and core bits but in their accessories too. The companys experience doesnt just extend to using the right speeds and suitable coolant and lubricant, it also covers all issues to do with thread cutting, reaming and countersinking. Thats because core drilling units from FEIN offer key benefits in these applications too. Experience them for yourself on the following pages. Please dont hesitate to contact your FEIN specialist dealer if you have any questions or require detailed advice. And if your core drilling unit isnt working, your FEIN service partner will have it up and running again in no time. Thats something you can rely on! FEINs service embodies complete reliability and lasting quality too.
29
THREAD CUTTING
Thread cutting tool with anti-clockwise rotation With a thread cutting tool, you can expand the functionality of pure core drilling units that only have clockwise rotation to include thread cutting. The tool enables anti-clockwise rotation and retracts the thread drill from the thread hole with precision.
Through hole
Blind hole
Save time with a quick change chuck A thread cutting quick change chuck is the most cost-effective solution for core drilling units with integrated anti-clockwise rotation.
No matter whether youre working with a through hole or blind hole, youll always achieve precise results in minimal time with FEIN core drilling units.
Customised thread cutting inserts FEIN thread cutting inserts are coordinated to the corresponding area of application depending on the thread type and thread drill in accordance with DIN 374/376. They are characterised by different inner diameters for a round shank and a square.
Steel < 500 N / mm2 Steel > 500 N / mm2 Stainless steel < 700 N / mm2 Cast iron (grey cast iron) < 300 N / mm2 Brass (CuZn) < 500 N / mm2
30
THREAD CUTTING
KBM 32 Q
KBM 50 QX
KBM 52 U
KBM 65 Q KBM 65 QF
From M 6 to M 27 FEIN has the right solution for every thread diameter.
440 rpm 260 rpm 260 rpm 250 rpm 260 rpm with M 20 180 rpm with M 27
9 26 02 072 01 2
9 26 02 072 01 2
9 26 02 079 01 0
9 26 02 066 01 2
9 26 02 082 01 0
Predrilling
Blind hole Blind hole Blind hole Through hole Through hole Through hole Thread / mm
Thread cutting
Blind hole Blind hole Blind hole
6 32 06 125 01 0
Through hole
Through hole
M6
5,0
6 39 01 023 02 0 6 32 06 117 01 5 6 32 06 118 01 3 6 32 06 117 01 5 6 32 06 118 01 3 6 32 06 117 01 5 6 32 06 118 01 3 6 32 06 117 01 5 6 32 06 118 01 3
6 32 06 125 01 0
+
6 32 06 117 01 5
Through hole
+
6 32 06 118 01 3
M8
6,8
6 39 01 023 02 0 6 32 06 095 01 1 6 32 06 102 01 3 6 32 06 095 01 1 6 32 06 102 01 3 6 32 06 095 01 1 6 32 06 102 01 3 6 32 06 095 01 1 6 32 06 102 01 3
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 095 01 1
+
6 32 06 102 01 3
M 10 8,5
6 39 01 023 02 0 6 32 06 096 01 4 6 32 06 103 01 7 6 32 06 096 01 4 6 32 06 103 01 7 6 32 06 096 01 4 6 32 06 103 01 7 6 32 06 096 01 4 6 32 06 103 01 7
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 096 01 4
+
6 32 06 103 01 7
M 12 10,2
6 39 01 023 02 0 6 32 06 097 01 8 6 32 06 104 01 5 6 32 06 097 01 8 6 32 06 104 01 5 6 32 06 097 01 8 6 32 06 104 01 5 6 32 06 097 01 8 6 32 06 104 01 5
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 097 01 8
+
6 32 06 104 01 5
M 14 12,0
6 31 27 086 01 9 6 39 01 023 02 0 6 32 06 098 01 6 6 32 06 105 01 9 6 32 06 098 01 6 6 32 06 105 01 9 6 32 06 098 01 6 6 32 06 105 01 9
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 098 01 6
+
6 32 06 105 01 9
M 16 14,0
6 31 27 088 01 1 6 39 01 023 01 1 6 32 06 099 01 0 6 32 06 106 01 2 6 32 06 099 01 0 6 32 06 106 01 2 6 32 06 099 01 0 6 32 06 106 01 2
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 099 01 0
+
6 32 06 106 01 2
M 18 15,5
6 31 27 238 01 1 6 39 01 023 01 1 6 32 06 100 01 1 6 32 06 107 01 6
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 100 01 1
+
6 32 06 107 01 6
M 20 17,5
6 31 27 239 01 5 6 32 06 101 01 0 6 32 06 108 01 4
6 32 06 125 01 0
6 32 06 125 01 0
+
6 32 06 101 01 1
+
6 32 06 108 01 4
M 22 19,5
6 31 27 240 01 7 6 32 06 119 01 0 6 32 06 122 01 0
M 24 21,0
6 31 27 095 01 5 6 32 06 119 01 0 6 32 06 122 01 0
M 27 24,0
6 31 27 098 01 0 6 32 06 120 01 0 6 32 06 123 01 0
31
COUNTERSINKING
* No responsibility is taken for the correctness of this information ** Solid TCT (SC)
Model
KBM 50 QX KBM 52 U KBM 65 Q / KBM 65 QF KBM 80 U KBM 80 auto
Countersink max.
31 mm 50 mm 50 mm 50 mm 50 mm
Deburr and countersink perfectly with FEIN core bit units such that nuts, screw heads and rivets lie flush to the workpiece surface.
32
REAMING
Model
KBM 50 QX KBM 52 U KBM 65 Q / KBM 65 QF KBM 80 U KBM 80 auto
Reaming max.
16 mm 23 mm 23 mm 31 mm 31 mm
For precise holes with outstanding surface quality mechanical reaming with FEIN core drilling units.
33
rpm
< 20
30
40
50
60
70
80
Diameter (mm)
rpm
10
15
20
25
30
35
Diameter (mm)
34
KBM 52U
KBM 32 Q KBM 32 Q
KBM 50 QX QX KBM 50
18 2
KBM 52 U
19 7
19 7
73 n3 mi x 570 ma
62 n3 mi x 660 ma
56 n4 mi x 692 ma
160 38 72 30 0
180 48 ,5 31 6
180 48 ,5 31 6
60
60
KBM 65 Q / KBM 65 QF
KBM 65 QF
KBM 80 U KBM 80 U
19 8
22
25
39 n4 mi x 766 ma
31 n5 mi x 818 a m
31 n5 mi x 818 a m
27
184 58 40 37 5
27 70 44 0
55
70
44
55
35
TECHNICAL DATA
KBM 50 QX 7 270 33
KBM 52 U 7 270 31
KBM 65 Q 7 270 29
KBM 65 QF 7 270 28 *
KBM 80 U 7 270 34
7 270 27
mm mm mm M mm mm watts watts rpm rpm rpm rpm rpm rpm QuickIN MT mm mm mm N 9 000
12 50 50 16 16 31 16
12 50 50 23 16 50 23 1 200 640
12 65 50 23 20 50 23 1 460 650
12 65 50 23 20 50 23 1 460 650
12 80 50 32 27 50 31 2 000 900
12 32 50 13 12
1 200 680
130 260 260 520 160 / 260 320 / 520 QuickIN QuickIN 3 125 / 250 255 / 510 QuickIN 3 145 330 125 / 250 255 / 510 QuickIN 3 145 330 +/ 6 +/ 8 11 000
QuickIN QuickIN QuickIN MAX QuickIN MAX 3 145 285 +/ 4,25 +/ 11 18 000
135 260
135 310
135 310
11 000
12 000
12 000
mm m kg
160 80 4 10,5
180 90 4 12,8
180 90 4 14,2
184 92 4 19,0
184 92 4 20,6
270 90 4 25,4
270 90 4 26,4
SERVICE
Qualified advice The professional and reliable power tools from FEIN are only available from specialist dealers, as this is the only way of guaranteeing you outstanding quality of advice for everything from choosing the right power tool to demonstrating its practical use. Your specialist dealer will be happy to help.
Authorised workshops No one can promise that a machine will work forever, especially in tough continuous use as an industrial production tool. But FEIN guarantees that if something should go wrong, it will soon be up and running again. With a dense network of qualified workshops that we have trained personally, FEIN provides a fast, low-cost service for servicing, repairs and safety checks.
Professional information Our application video for core drilling includes professional user tips for efficient and safe working. The video explains all the key applications and core drilling units in detail. Order number 3 41 30 385 06 0
PC: Pentium IV, Windows 2000 or higher, min. 512 MB free memory, monitor with 1024 x 768 pixels, 4x DVD-ROM drive Mac: G4 processor, OSX 10.2 or higher, min. 512 MB free memory, monitor with 1024 x 768 pixels, 4x DVD-ROM drive To watch the videos on a computer, DVD-player software is required.
3-year FEIN PLUS warranty Register your new FEIN core drilling unit online at www.fein.com within six weeks of purchase and youll immediately receive a warranty certificate, which in certain countries allows you to enjoy the 3-year FEIN PLUS warranty if you also keep hold of your sales receipt.
www.fein.com
3 41 30 385 06 0
37
Do you have any further questions? Or would you like to test the FEIN core drilling units?
Germany: C. & E. FEIN GmbH, Hans-Fein-Str. 81, 73529 Schwbisch Gmnd-Bargau Great Britain: FEIN Industrial Power Tools UK Ltd., 4 Badby Park, Heartlands Business Park, Daventry, Northants NN11 8YT, Phone 01327 308730
Australia: FEIN Power Tools Pty. Ltd., Unit 7/55 61 Pine Road, Yennora N.S.W. 2161; P.O. Box 328, Fairfield N.S.W. 1860, Phone 1300 798 688 India: FEIN Power Tools India Pvt. Ltd., 69 Arcot Road, Kodambakkam, Chennai - 600 024, Phone 044-43 578 680, Fax 044-24837788 Regional Office of Asia Pacific: FEIN Power Tools Asia Limited, A1, 11/F, Block A, Mai Hing Industrial Building, 16-18 Hing Yip Street, Kwun Tong, Kowloon, Hong Kong, Phone +852 2341-1026, Fax +852 2341-2250
www.fein.com
Printed in Germany. Diagrams not binding. Technical details subject to change. 1 88 31 687 01 0 12.09 EN.