Professional Documents
Culture Documents
Anchor Systems
Introduction Anchor Selection Chart Anchor Technical Software Profis Product Approvals / ETA Advantage Fire Resistance / Corrosion and Chemical Attack / Setting Operation
PAGE
Adhesive Anchors HVZ adhesive anchors (for cracked concrete) 263 HVU adhesive anchor system 264-266 Hilti HIT system 267-268 HIT-HY systems 269-271 HIT-RE500 for reinforced concrete 272-273 Dispensers and accessories for HIT 274-276 Heavy Duty Metal Anchors HDA undercut anchor and accessories 277-278 HSL3 heavy duty expansion anchor 279-280 HSC self cutting anchor and accessories 281-282 Medium Duty Metal Anchors HST safety stud anchor 283-284 HSA standard stud anchor 285-286 HKD-S push-in anchor 287-288 HLC sleeve anchor 289-290 HB Hilti bolt 291 HUS (10.5 / 12.5 and 16.5) universal screw anchor 292 HUS-HF universal screw anchor 293 Light Duty Metal & Plastic Anchors HUS-H (7.5) universal screw anchor 294-295 HT metal frame anchor 296 HPF /2 plastic frame anchor 297 HRD / U plastic frame anchors 298-300 Fixings for scaffolding and restraints 301 HHD-S cavity anchor 302 HLD light duty anchor 303 HSP / HFP drywall anchor 304 HPS-1 hammer screw 304 DBZ wedge anchor metal nail-in 305 HA8 ring anchor ceiling anchor 305 HUD-1 universal anchor 308 Insulation Fasteners IZ expansion insulation fasteners IDP insulation fasteners IDMR metal insulation fasteners Special Products Remedial wall ties, Test meter equipment Rail anchors
Hilti. Outperform. Outlast.
309 310
258
Anchor Systems
259
PROFIS
Other major features include: From quick, rough and dirty calculations to fully defined designs. Graphical input with all dimensions and loading visible. User-defined print output. Easy-to-understand Anchor setting animations. Supports 13 different design methods and 16 languages. Always up to date with regular downloads and add-ons. Workshop drawings to ensure the fabricators get it right. Free downloads.
260
Anchor Systems
Please do not hesitate to contact us if you would like any further information. What are ETAs? A European Technical Approval (ETA) is, an approval system for products which cannot be standardised performance driven recognised throughout Europe a requirement for CE marking When should I use products with ETAs? ETAs are most beneficial, when the product will be permanently installed into the works if failure would cause risk to human life and/or serious economic consequences
As an international company, Hilti has gained many approvals for its products.
What are benefits to the specifier? By specifying these products in accordance with the guideline (ETAG) you can, produce efficient designs show clear, independent evidence of the safety of your designs show compliance with building regulations use the same design across Europe without the need for local approvals
DIBt
FM Factory Mutual
HST, HKD-S
How can Hilti help the specifier? Hilti is now available to offer products with ETAs. We offer a comprehensive range of technical support,
SOCOTEC
(Technical Controlling Body) HSL, HVU, HST, HST-R, HSA-KA, HSA-KR, HSC-A, HSC-I, HLC, HLC-H, HPS-1
copies of ETAs copies of the design method ETAG Annex C (also available on CD ROM) guidance note - Introduction to European Technical Approvals for CE marking telephone technical advice technical specialists can visit your office or site Hilti Anchor Design Profis Program CD ROM includes options to design to the ETAG
The following products meet or exceed the JCAA product classification requirements HSL, HKD-S, HVU
261
Fire Resistance
When subject to high temperatures, as in fire, the properties of both the anchor and the surrounding base material are degraded. In order to provide customers with appropriate information for fixings which are to be used in situations where they cannot be protected from the possibility of fire, Hilti carries out fire tests on most anchors. These assessments and performance ratings are confirmed by Warrington Fire Research Centre based on BS 476.
Setting Operation
By installing Hilti anchors within the guide ines of published Hilti method statements and setting instructions you can expect to obtain the loads stated within this Guide. However, any deviation from the installation process and ignoring the following points below may result in poor anchor performance. DRILL BITS & DIAMOND CORE BITS A drill bit/diamond core bit of the correct nominal diameter must always be used. If Hilti drill bits/diamond core bits are used you have the assurance that the drill/diamond core bit tolerance and hole geometry have been co-ordinated accurately with all Hilti anchors. Detailed below are nominal drill bit/diamond core bit sizes and the actual size the drill bit/diamond core bit should be when new. If the drill bit/diamond core bit size is outside the range detailed, anchor performance will be reduced.
Nominal Bit Size (mm) Actual Drill Bit Size New (mm) Actual Diamond Core Bit Size New (mm) 8.0 - 8.2 10.0 - 10.2 12.0 - 12.2 13.0 - 13.2 14.0 - 14.2 15.0 - 15.2 16.0 - 16.2 18.0 - 18.2 20.0 - 20.2 22.0 - 22.2 24.0 - 24.2 25.0 - 25.2 28.0 - 28.2 32.0 - 32.2
GALV
Galvanised Finish
A2 304
Corrosion Resistance
A4 316
Corrosion Resistance
HCR
high Mo
Corrosion Resistance
The usual basic coating for most Hilti anchors is electro-galvanised (zinc plated) to 5mm. This coating gives some degree of protection but is most suitable in dry, indoor conditions. Improved resistance can be provided by hot-dip galvanising or equivalent mechanical processes. The Galvanised Finish Symbol indicates that such a superior coating is available. A2 grade stainless steel provides better corrosion resistance than galvanised coatings. Anchors can be produced in this grade if requested. This material is generally less expensive than A4 grades. Materials in the A4 group (stainless steel) or those of a higher quality should be used for fastenings exposed to a greater risk of corrosion, such as those in town air, industrial atmosphere, coastal climate and in road construction. For normal requirements, stainless steel A4 grade has a high resistance to corrosion. In chemically aggressive environments even A4 has difficulty maintaining its mechanical integrity. Tunnels, indoor swimming pools, facilities exposed to sea water, water treatment plants and chemical/power plants would all fit into this category. Hilti have developed a range of anchor products so that fastening solutions can be offered in these corrosive environments. The material, HCR, is a chromium-nickel steel alloy with a high molybdenum content. The HAS-HCR rods have similar mechanical properties and performance to the A4 HAS-R versions. Details are given in the product information pages. Hilti products accompanied with this symbol are available in HCR.
5 5.15 - 5.4 6 6.15 - 6.4 6.5 6.6 - 6.81 8 8.2 - 8.45 10 10.2 - 10.45 12 12.2 - 12.50 1 /213 13.0 - 13.3 14 14.2 - 14.5 15 15.2 - 15.5 16 16.2 - 16.6 18 18.3 - 18.5 20 20.1 - 20.55 22 22.21 - 22.55 24 24.3 - 24.5 25 25.1 - 25.55 28 28.3 - 28.55 32 32.4 - 32.7 Note: Drill bit sizes to DIN 8035.
HOLE CLEANING Recommended load values require careful cleaning of the hole in line with the setting instructions provided for the chosen product. Holes for adhesive anchors may be flushed out with water, but all standing water must be removed before the resin is inserted. The HIT-HY range of resin anchors should be used in percussion drilled holes. If a diamond cored hole is to be used, it must be suitably conditioned in order to roughen the surface. Please contact us if in doubt. It is recommended that the holes for expansion anchors are cleaned and allowed to dry. Drilling dust or slurry can have a detrimental affect on anchor holding power.
262
Anchor Systems
Drill holes.
tgel
tcure
Tinst
Inject washer Allows baseplate clearance hole to be filled with HIT HY150. This ensures that the applied shear load is distributed evenly on to all anchors.
Spherical washer Prevents local stress raisers if hole is not drilled square to surface. Nut & Locknut Prevents nut from working loose under vibration.
Technical data: HVZ, HVZ-RTZ, HVZ-HCRTZ Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete Cracked concrete
HVZ HVZ-RTZ HVZ-HCRTZ Anchor size Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec M10 15.6 10.3 15.6 11.4 15.6 11.4 M12 19.1 15.4 19.1 17.1 19.1 17.1 M16 25.8 29.1 25.8 32.0 25.8 32.0 M16L 33.6 29.1 33.6 32.0 33.6 32.0 M20 53.2 50.3 53.2 56.0 53.2 56.0 M10 9.5 10.3 9.5 11.4 9.5 11.4 M12 15.9 15.4 15.9 17.1 15.9 17.1 M16 18.4 29.1 18.4 32.0 18.4 32.0 M16L 23.9 29.1 23.9 32.0 23.9 32.0 M20 38.0 50.3 38.0 56.0 38.0 56.0
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
with external hexagon, complete with nut and washer Steel galvanised to 10 microns Stainless steel of A4-80 grade
Ordering designation Item no. Ordering designation
Dynamic set
Ordering designation
M10 M10 M10 M12 M12 M12 M12 M16 M16 M16 M16 M16 M16 M20
10 10 10 10 10 10 10 10 10 10 10 10 10 10
HVU-TZ M10 HVU-TZ M10 HVU-TZ M10 HVU-TZ M12 HVU-TZ M12 HVU-TZ M12 HVU-TZ M12 HVU-TZ M16 HVU-TZ M16 HVU-TZ M16 HVU-TZ M16 HVU-TZ M16 HVU-TZ M16 HVU-TZ M20
00311368 00311368 00311368 00311369 00311369 00311369 00311369 00311370 00311370 00311370 00311370 00311370 00311370 00335942
HAS-TZ M 10x75/15 HAS-TZ M 10x75/30 HAS-TZ M 10x75/50 HAS-TZ M 12x95/25 HAS-TZ M 12x95/50 HAS-TZ M 12x95/100 HAS-TZ M 16x105/30 HAS-TZ M 16x105/60 HAS-TZ M 16x105/100 HAS-TZ M 16x125/30 HAS-TZ M 16x125/60 HAS-TZ M 16x125/100 HAS-TZ M 20x170/40
00310018 00308383 00308384 00308385 00308386 00308387 00308388 00308389 00308390 00332519 00332520 00332521 00335943
HAS-RTZ M 10x75/15 HAS-RTZ M 10x75/30 HAS-RTZ M 10x75/50 HAS-RTZ M 12x95/25 HAS-RTZ M 12x95/40 HAS-RTZ M 12x95/50 HAS-RTZ M 12x95/100 HAS-RTZ M 16x105/30 HAS-RTZ M 16x105/60 HAS-RTZ M 16x105/100 HAS-RTZ M 16x125/30 HAS-RTZ M 16x125/60 HAS-RTZ M 16x125/100 HAS-RTZ M 20x170/40
00310019 00308391 00308392 00308393 00333769 00308394 00308395 00308396 00308397 00308398 00332522 00332523 00332524 00335944
Dynamic Set M10 Dynamic Set M10 Dynamic Set M10 Dynamic Set M12 Dynamic Set M12 Dynamic Set M12 Dynamic Set M12 Dynamic Set M16 Dynamic Set M16 Dynamic Set M16 Dynamic Set M16 Dynamic Set M16 Dynamic Set M16 Dynamic Set M20
00369201 00369201 00369201 00369202 00369202 00369202 00369202 00369203 00369203 00369203 00369203 00369203 00369203 00369204
Setting tools for HVA and HVZ (anchor rods with external hexagon)
Ordering designation
TE-C HEX M10 TE-C HEX M12 TE-C HEX M16 TE-Y HEX M20
TE-56 TE-76 m 2) 3) m 2) 3) l l
Item no.
1)
2) 3)
l m
use with TE-C-WZA chuck use TE-FY-BY-C setting adaptor use low hammering power for HAS(-R) suitable for HAS / HAS-R and HAS-TZ / HAS-RTZ only suitable for HAS-TZ / HAS-RTZ
263
Use n Heavy-duty fastenings with small spacing and edge distances n Suitable for making fixings underwater (contact Technical Advisory Service for details)
System n Consisting of adhesive in a foil capsule and an anchor rod or internally threaded sleeve
trel
tcure
7
Features
A virtual odourless resin system containing no styrene n Good flow properties and surface wetting n Unaffected by temperature and weather, in any season or climatic zone n Excellent and constant anchor holding power due to a new resin system and a larger amount of quartz granules n Good fire resistance properties
n
Technical data: HVU, HAS, HAS-R, HAS-HCR Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 HVU + HAS
Anchor size Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec M8 7.8 5.6 8.8 6.3 M10 11.8 9.0 11.8 10.1 M12 17.0 13.1 17.0 14.6 M16 24.8 24.7 24.8 27.7 M20 44.9 38.6 44.9 43.3 M24 64.7 55.6 64.7 62.3 M27 79.2 117.1 63.6 45.8 M30 104.0 142.4 77.2 55.6 M33 122.1 177.4 96.3 69.4 M36 145.2 208.2 113.0 81.3 M39 166.4 250.4 135.9 97.9
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
80 HAS M 8 90 HAS M10 110 HAS M12 125 HAS M16 170 HAS M20 210 HAS M24 240 HAS M27 270 HAS M30 300 HAS M33 330 HAS M36 360 HAS M39 Storage temperature 5 to 25C
10 12 14 18 24 28 30 35 37 40 42
14 18 22 28 32
10 10 10 10 5 5 4 4 4 2 2
HVU M 8 80 HVU M10 90 HVU M12110 HVU M16125 HVU M20170 HVU M24210 HVU M27240 HVU M30270 HVU M33300 HVU M36330 HVU M39360
00256691 00256692 00256693 00256694 00256695 00256696 00256697 00256698 00256699 00256700 00256701
Anchor rod and Setting tools see page 265-266 For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
264
Anchor Systems
System n Consisting of the anchor rod and adhesive in a foil capsule. Features n Time saving and economical to install. n Ideal for use with Hilti HVU adhesive capsules. n Ready to use, thus practical, efficient use of material. n Also available in stainless-steel versions.
Natural stone
Hollow bricks
HVU M10 90 HVU M12110 HVU M16125 HVU M20170 HVU M24210
10 10 5 5 5
13 17 19 24 30
Drive sockets
Use with TE connection For anchor Ordering designation Item no.
TE-C HIS 1/20 TE-C HIS 1/20 TE-C HIS 1/20 TE-FY HIS 3/40 TE-FY HIS 3/40 TE-FY HIS 3/40 TE-FY HIS 3/40 TE-FY HIS 3/40 TE-FY HIS 3/40 TE-FY HIS 3/40 * TE-FY HIS 3/40 *
HIS-N M8 HIS-N M10 HIS-N M12 HIS-N M12 HIS-N M16 HIS-N M20 HAS M27 HAS M30 HAS M33 HAS M36 HAS M39
13mm socket 1/20 17mm socket 1/20 19mm socket 1/20 19mm socket 3/40 24mm socket 3/40 30mm socket 3/40 41mm socket AF 3/40 46mm socket AF 3/40 50mm socket AF 3/40 55mm socket AF 10 60mm socket AF 10
s 00060186 s 00060187 s 00060188 s 00045898 s 00060190 s 00060191 s 3072272 s 3072273 s 3072274 s 3072270 s 3072271
l l
l l
TE-C-HIS 1/2
For adaptor size SA 8-SA 16 For adaptor size SA 20-SA 24 For all hole sizes For hole sizes up to 16 mm dia. For hole sizes 20 and 24 mm dia.
SW 8 Allen wrench SW 12 Allen wrench Blow-out pump G 34 Wire brush 3/T 69 Flat brush
00059185 00059186 00060579 00001226 00003206 s PLEASE ASK FOR DELIVERY DETAILS.
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
265
HAS anchor rod, complete with hexagon nut and washer, with external drive hexagon
Connection thread Fastenable thickness (mm) Rod length (mm) Package contents Tightening torque, Steel zinc plated 5 microns thick (grade 5.8 / ISO 898 T1) Tinst.(Nm) Ordering designation Item no. Stainless steel A4-70 SS 316 (material 1.4401) Ordering designation Item no.
M 8 M 8 M 8 M10) M10 M10 M10 M12 M12 M12 M12 M16 M16 M16 M16 M16
110 150 240 130 170 190 220 160 220 260 300 190 260 300 350 500
20 20 10 10 10 10 10 10 10 10 10 5 5 5 5 5
HAS M 8110/ 14 HAS M 8150/ 54 HAS M10130/ 21 HAS M10170/ 61 HAS M10190/ 81 HAS M12160/ 28 HAS M12220/ 88 HAS M12260/128 HAS M12300/168 HAS M16190/ 38 HAS M16260/108 HAS M16300/148 HAS M16350/198 HAS M16500/348
00066001 00259934 00066002 00259936 00259937 00066003 00259938 00259939 00259940 00066004 00259941 00259942 00259943 00259944
HAS-R M 8110/ 14 HAS-R M 8150/ 54 HAS-R M 8240/114 HAS-R M10130/ 21 HAS-R M10170/ 61 HAS-R M10190/ 81 HAS-R M10220/114 HAS-R M12160/ 28 HAS-R M12220/ 88 HAS-R M12260/128 HAS-R M12300/168 HAS-R M16190/ 38 HAS-R M16260/108 HAS-R M16300/148 HAS-R M16350/198
00259945 00259946 00259947 00259948 00259949 00259950 00259951 00259952 00259953 00259758 00259759 00259954 00259955 00259760 00259956
TE-C HEX M10 TE-C HEX M12 TE-C HEX M16 TE-Y HEX M20
Item no.
1)
HAS-E anchor rod, complete with hexagon nut and washer, with cone head
Connection thread Fastenable thickness (mm) Embedment depth (mm) Package contents Overall length (mm) Tightening torque Steel zinc plated 5 microns thick (grade 5.8 / ISO 898 T1) Tinst.(Nm) Ordering designation Item no. Stainless steel A4-70 (material 1.4401) Ordering designation Item no.
A4 316
M8 14 80 15 80 M8 114 80 M8 21 90 M10 61 90 M10 81 90 M10 88 90 M10 28 110 M12 88 110 M12 128 110 M12 168 110 M12 20 125 M16 38 125 M16 108 125 M16 148 125 M16 198 125 M16 348 125 M16 48 170 M20 68 170 M20 108 170 M20 158 170 M20 208 170 M20 54 210 M24 60 240 M27 70 270 M30 80 300 M33 90 330 M36 100 360 M39 * (Grade 8.8 / ISO 898 T1)
20 10 10 20 10 10 10 20 10 10 10 10 20 10 10 10 10 10 10 10 10 10 10 4 4 4 4 4
110 150 240 130 170 190 220 160 220 260 300 170 190 260 300 350 500 240 260 300 350 400 290 340 380 420 460 500
15 15 15 30 30 30 30 50 50 50 50 100 100 100 100 100 100 160 160 160 160 160 240 270 300 1200 1500 1800
HAS-E M8 80/14 HAS-E M8 80/54 HAS-E M10 90/21 HAS-E M10 90/61 HAS-E M10 90/81 HAS-E M12 110/28 HAS-E M12 110/88 HAS-E M12 110/128 HAS-E M12 110/168 HAS-E M16 125/20 HAS-E M16 125/38 HAS-E M16 125/108 HAS-E M16 125/148 HAS-E M16 125/198 HAS-E M16 80/348 HAS-E M20 170/48 HAS-E M20 170/68 HAS-E M20 170/108 HAS-E M20 170/158 HAS-E M20 170/208 HAS-E M24 210/54 HAS-E M27 240/60 * HAS-E M30 270/70 * HAS-E M33 300/80 * HAS-E M36 330/90 * HAS-E M39 360/100 *
00332219 00333099 00332220 00333100 00333101 00332221 00333102 00333103 00333104 00333105 00332222 00333106 00333107 00333108 00333109 00332223 00333110 00333111 00333112 00333113 00332224 00333114 00333115 00333116 00333117 00333118
HAS-E-R M8 80/14 HAS-E-R M8 80/54 HAS-E-R M10 80/114 HAS-E-R M10 90/21 HAS-E-R M10 90/61 HAS-E-R M10 90/81 HAS-E-R M10 90/88 HAS-E-R M12 110/28 HAS-E-R M12 110/88 HAS-E-R M12 110/128 HAS-E-R M12 110/168 HAS-E-R M16 125/20 HAS-E-R M16 125/38 HAS-E-R M16 125/108 HAS-E-R M16 125/148 HAS-E-R M16 125/198 HAS-E-R M20 170/48 HAS-E-R M20 170/108 HAS-E-R M24 210/54 HAS-E-R M27 240/60 * HAS-E-R M30 270/70 * HAS-E-R M33 300/80 * HAS-E-R M36 330/90 * HAS-E-R M39 360/100 *
00333119 00333120 00333121 00333122 00333123 00333124 00333125 00333126 00333127 00333128 00333129 00333130 00333131 00333132 00333133 00333134 00333135 00333136 00333137 00333138 00333139 00333140 00333141 00333142
l l l l
TE-C-E M 8 TE-C-E M10 TE-C-E M12 TE-C-E M16 TE-Y-E M16 TE-Y-E M20 TE-Y-E M24
266
HY 70
HY 150
RE 500
Dispensers
For foil packs (330/500ml) manual battery pneumatic
Base material
330 ml
ED 3500
MD 2500
500 ml
ED 3500
P 8000
1400 ml
500 kg - 5400 kg
Nozzles
HY (330 / 500 ml) HY (Jumbo) RE 500
3x 3x
MD 2000
Drill hole.
Put holder with foil pack into dispenser. Fill hole with adhesive.
* Additional sizes, different materials and surface finishes are available through our Specials Department.
267
Anchor Systems
Reliable Clean
For fastening a variety of fasteners into many different base materials within a wide range of temperatures.
Consistent fastenings; no expansion forces exerted on base material. No direct contact with the adhesive, since there is no manual mixing; no setting tools required.
Easy To Use
Easy dispensing adhesive even in cold temperatures. Applicationmatched, compact system; simply drill and clean the hole, dispense the adhesive and insert the fastener or rebar.
Economical
Uniform Quality
Mixing errors eliminated; two components of the adhesive are in separate containers and are proportional and mixed as they are dispensed.
Waste is minimal since only the amount required for the job is used. If adhesive is not completely dispensed during initial usage, cartridge may be reused; one cartridge may be sufficient for several fastenings. Cartridge waste volume for disposal is also minimal.
HY 70
Reinforcement connecting to existing concrete designed according to reinforced concrete theory quick curing for small bars. Anchor fixings to mass concrete with threaded rods and anchor sleeves.
Fixing to solid brick or blockwork masonry. Remedial and extension wall tie applications to solid brick or block masonry.
n n
HY 150
HIT RE 500
n
Anchoring large and deep rebars to mass reinforced concrete. Slow cure enables bigger fixings to be made. Ensures reliable fastenings even when diamond drilled holes rock drilled holes poorly cleaned, wet or oversized holes.
HY 70 HY 70
HIT HY 70
n
With sieve anchorage to hollow concrete floors with anchor rod or threaded insert. With sieve to face of perforated brick/block with anchor rod or threaded insert.
268
Anchor Systems
Advantages Optimized application, comfortable and flexible For indoor and outdoor applications, as well as for use in dry and wet drilled holes Can be used at any time of year in a temperature range between 5 and +40 C Fastenings are free of expansion forces and approved by technical approval departments Non-bearing surfaces are effortlessly bridged High degree of fire resistance Mortar injection control: the user identifies when the correct mortar amount has been injected. Less mortar loss and lower costs per fastening point with full performance.
Flexible embedment depths and variable loads in spite of fewer parts: Hiltis unique, combinable, corrosion free, composite mesh sleeve makes it possible!
330 ml
HIT-HY 70/ 330/2 HIT-HY 70/ 330/2 HIT-HY 70/ 500/2 HIT-HY 70/ 500/1 HIT-HY 70/1400/1
1 20 Promo Box 1 1 1
500 ml
1400 ml
M 6 80/14 M 8 80/14 M 10 80/20 M 12 80/23 M 12110/28 * M 16125/38 * M 8 80/14 M 10 80/20 M 12 80/23 M 12110/28 * M 16125/38 *
Galvanized Galvanized Galvanized Galvanized Galvanized Galvanized Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel
20 20 10 10 10 5 20 10 10 10 5
HIT-AC HAS HIT-AC HIT-AC HAS HAS HAS-R s HIT-AC-R s HIT-AC-R HAS-R HAS-R
M 6 80/14 M 8 80/14 M10 80/20 M12 80/23 M12110/28 M16125/38 M 8 80/14 M10 80/20 M12 80/23 M12110/28 M16125/38
274486 066001 274487 274488 066003 066004 259945 274489 274490 259952 259954
HIT-AC
Static Mixer
Ordering Designation) Packaging contents Ordering designation Item no.
269
Anchor Systems
0-Vollstein 006
2 3
HIT-HY70-Ziegel 07.09.2006
7
1
2
2x
2x
2x
2x
2x
2x
10
3 2 1
11
10
3 2 1
11
2x 330ml 3x 500ml
2x 330ml 3x 500ml
11
10
10
12
HIT-SC
13
HIT-SC
14
HIT-S
1x
10
11
tgel
12
tcure
13
Tinst
15
tgel
16
tcure
17
Tinst
11
F 23 32 41 50 68 86 104
C -5 0 5 10 20 30 40
12
F 23 32 41 50 68 86 104
C -5 0 5 10 20 30 40
15 F
23 32 41 50 68 86 104
C -5 0 5 10 20 30 40
16 F
23 32 41 50 68 86 104
C -5 0 5 10 20 30 40
270
Anchor Systems
Hilti HIT-HY150
Base material n Concrete n Hard natural stone
Use n Connectors n Anchor rods n Internally threaded sleeves n Reinforcing bars up to T25 (max.) Material n Hilti HIT-HY 150 hybrid adhesive Features n Fastenings without expansion pressure n High loading n User-friendly, odourless n Small edge distances n Complete system of matched components
Fire Data Available grade 5.8 anchor rods fail before the resin in a fire
(330 ml)
(500 ml)
3x
3 3x
4
M D 20 00
2x
(1400 ml)
5
MD 2000
Tinst
Base material temperature OC Tgel (min) Tcure (min) -5 90 360 0 45 180 5 25 90 20 6 50 30 4 40 40 2 30 The foil pack temperature must be at least +5OC
Technical data: HIT-HY 150 + HAS, HIT-HY 150 + HAS-R / HAS-HCR Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 HIT-HY 150 + HAS
Anchor size Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec M8 6.0 5.6 6.0 6.3 M10 8.0 9.0 8.0 10.1 M12 12.0 13.1 12.0 14.6 M16 15.3 24.7 25.3 27.7 M20 26.0 38.6 26.0 43.3 M24 32.4 55.6 32.4 62.3
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
2 2 0 1
Foil pack HY150/330/2 Foil pack HY150/330/2 Foil pack HY150/330/0 Foil pack HY150/1400/1
2 2 2 2 2
20 40 60 80 100
271
Anchor Systems
Hilti HIT-RE 500 Optimal curing for professional fastening of reinforcing bars up to T40 into large deep holes Reliable n Very high loading values with reinforcing bars in a wide range of diameters (8 to 40 mm dia.) n Optimum working time in the extended temperature range from - 5 to + 40C n Suitable for use in holes drilled using diamond coring equipment, rotary hammers, pneumatic drills n Low sensitivity to oversized holes, dusty and wet holes n Red coloured adhesive for easy checking of proper setting on site n Comprehensive technical data for effective fastening design Convenient n Well proven, self-opening foil pack system n Low dispensing force for quick and easy work n Wide range of dispensers for different requirements Environmentally friendly Reduced waste due to unique foil pack n Odourless adhesive
n
cures at
- 5OC
Item no.
Ordering designation
HIT-RE-M static mixer 1 suitable for foil pack and jumbo cartridge HIT-EXT 9/1000 Length: 1000 mm, External diameter: 9 mm HIT-EXT 16/700 Length: 700 mm, External diameter: 16 mm
Setting operations 1 2 3
Features n The new adhesive ensures reliable fastening, even when holes are drilled using diamond coring equipment or pneumatic drills, are poorly cleaned, wet or oversized n Convenient dispensing tools for different requirements
t cure , ini t cure , fu 36h 72h 25h 50h 12h 24h 6h 12h 4h 8h 2h 4h
Technical data: HIT-RE 500 + rebar Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 HIT-RE + rebar
Anchor size Tensile N Rec Shear V Rec 8 9.9 7.9 10 14.1 12.4 12 20.6 17.8 14 27.3 24.2 16 31.2 31.6 20 53.0 49.5 25 81.8 77.1 28 102.8 96.6 32 120.9 126.2 36 137.7 169.5 40 154.4 197.4
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
1 20
HIT-RE 500/1400/1
s PLEASE ASK FOR DELIVERY DETAILS. For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie Hilti. Outperform. Outlast.
272
Anchor Systems
System n Consisting of the anchor rod and HIT injection resin with dispenser Features n Time saving and economical to install. n Ideal for use with Hilti HIT-HY injection resin. n Ready to use, thus practical, efficient use of material. n Also available in stainless-steel versions.
10 10 5 5 5
HAS anchor rod, complete with hexagon nut and washer, with external drive hexagon
Connection thread Fastenable thickness (mm) Rod length (mm) Package contents Tightening torque, Steel zinc plated 5 microns thick (grade 5.8 / ISO 898 T1) Tinst.(Nm) Ordering designation Item no. Stainless steel A4-70 SS 316 (material 1.4401) Ordering designation Item no.
M 8 M 8 M 8 M10 M10 M10 M10 M12 M12 M12 M12 M16 M16 M16 M16 M16
110 150 240 130 170 190 220 160 220 260 300 190 260 300 350 500
20 20 10 10 10 10 10 10 10 10 10 5 5 5 5 5
HAS M 8110/ 14 HAS M 8150/ 54 HAS M10130/ 21 HAS M10170/ 61 HAS M10190/ 81 HAS M12160/ 28 HAS M12220/ 88 HAS M12260/128 HAS M12300/168 HAS M16190/ 38 HAS M16260/108 HAS M16300/148 HAS M16350/198 HAS M16500/348
00066001 00259934 00066002 00259936 00259937 00066003 00259938 00259939 00259940 00066004 00259941 00259942 00259943 00259944
HAS-R M 8110/ 14 HAS-R M 8150/ 54 HAS-R M 8240/114 HAS-R M10130/ 21 HAS-R M10170/ 61 HAS-R M10190/ 81 HAS-R M10220/114 HAS-R M12160/ 28 HAS-R M12220/ 88 HAS-R M12260/128 HAS-R M12300/168 HAS-R M16190/ 38 HAS-R M16260/108 HAS-R M16300/148 HAS-R M16350/198
00259945 00259946 00259947 00259948 00259949 00259950 00259951 00259952 00259953 00259758 00259759 00259954 00259955 00259760 00259956
A4 316
HAS-E anchor rod, complete with hexagon nut and washer, with cone head
Connection thread Fastenable thickness (mm) Embedment depth (mm) Package contents Overall length (mm) Tightening torque Steel zinc plated5 microns thick (grade 5.8 / ISO 898 T1) Tinst.(Nm) Ordering designation Item no. Stainless steel A4-70 (material 1.4401) Ordering designation Item no.
M8 14 80 15 80 M8 114 80 M8 21 90 M10 61 90 M10 81 90 M10 88 90 M10 28 110 M12 88 110 M12 128 110 M12 168 110 M12 20 125 M16 38 125 M16 108 125 M16 148 125 M16 198 125 M16 348 125 M16 48 170 M20 68 170 M20 108 170 M20 158 170 M20 208 170 M20 54 210 M24 60 240 M27 70 270 M30 80 300 M33 90 330 M36 100 360 M39 * (Grade 8.8 / ISO 898 T1)
20 10 10 20 10 10 10 20 10 10 10 10 20 10 10 10 10 10 10 10 10 10 10 4 4 4 4 4
110 150 240 130 170 190 220 160 220 260 300 170 190 260 300 350 500 240 260 300 350 400 290 340 380 420 460 500
15 15 15 30 30 30 30 50 50 50 50 100 100 100 100 100 100 160 160 160 160 160 240 270 300 1200 1500 1800
HAS-E M8 80/14 HAS-E M8 80/54 HAS-E M10 90/21 HAS-E M10 90/61 HAS-E M10 90/81 HAS-E M12 110/28 HAS-E M12 110/88 HAS-E M12 110/128 HAS-E M12 110/168 HAS-E M16 125/20 HAS-E M16 125/38 HAS-E M16 125/108 HAS-E M16 125/148 HAS-E M16 125/198 HAS-E M16 80/348 HAS-E M20 170/48 HAS-E M20 170/68 HAS-E M20 170/108 HAS-E M20 170/158 HAS-E M20 170/208 HAS-E M24 210/54 HAS-E M27 240/60 * HAS-E M30 270/70 * HAS-E M33 300/80 * HAS-E M36 330/90 * HAS-E M39 360/100 *
00332219 00333099 00332220 00333100 00333101 00332221 00333102 00333103 00333104 00333105 00332222 00333106 00333107 00333108 00333109 00332223 00333110 00333111 00333112 00333113 00332224 00333114 00333115 00333116 00333117 00333118
HAS-E-R M8 80/14 HAS-E-R M8 80/54 HAS-E-R M10 80/114 HAS-E-R M10 90/21 HAS-E-R M10 90/61 HAS-E-R M10 90/81 HAS-E-R M10 90/88 HAS-E-R M12 110/28 HAS-E-R M12 110/88 HAS-E-R M12 110/128 HAS-E-R M12 110/168 HAS-E-R M16 125/20 HAS-E-R M16 125/38 HAS-E-R M16 125/108 HAS-E-R M16 125/148 HAS-E-R M16 125/198 HAS-E-R M20 170/48 HAS-E-R M20 170/108 HAS-E-R M24 210/54 HAS-E-R M27 240/60 * HAS-E-R M30 270/70 * HAS-E-R M33 300/80 * HAS-E-R M36 330/90 * HAS-E-R M39 360/100 *
00333119 00333120 00333121 00333122 00333123 00333124 00333125 00333126 00333127 00333128 00333129 00333130 00333131 00333132 00333133 00333134 00333135 00333136 00333137 00333138 00333139 00333140 00333141 00333142
273
Anchor Systems
ED 3500 basic kit w/o battery & charger ED 3500 complete kit with battery pack & charger SFB 126 battery C 7/36 battery charger
ED 3500 tool only in cardboard box ED 3500 kit in plastic case Battery pack Battery charger
Manual dispensers
The MD 2000 takes 330 ml cartridges The MD 2500 takes 330 ml and 500 ml cartridges
Consisting of: Ordering designation Item no.
MD 2000 dispenser, 2 cartridge holders blow-out pump and 3 brushes in plastic case MD 2500 dispenser, 2 cartridge holders blow-out pump and 3 brushes in plastic case
00229155 00369220
MD 2000 MD 2500
00229154 00338853
00229170 00339477
Item no.
Dispenser for 330ml Dispenser for 330 / 500ml Dispenser for 1400ml
s s
Accessories
Package contents Ordering designation Item no.
1 1 1 1 GA = thread connection
Ordering designation
Blow-out pump Round brush with grip 13 mm dia. Round brush with grip 18 mm dia. Round brush with grip 28 mm dia.
Packaging (pcs)
Item no.
HIT-HY-M mixer
00256082
Roughening tool
TE-Y-RT 16/40 TE-Y-RT 18/40 TE-Y-RT 22/40 TE-Y-RT 28/55 1 1 1 1 00259590 00259591 00259592 00259593 s PLEASE ASK FOR DELIVERY DETAILS. For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
274
Anchor Systems
20 20 20 20 20 20
HIT-SC 1250 HIT-SC 1285 HIT-SC 1650 HIT-SC 1685 HIT-SC 2250 HIT-SC 2285
10 10 10 10 10 10
HIT-IC M 850 HIT-IC M 1050 HIT-IC M 1250 HIT-IC M 880 HIT-IC M 1080 HIT-IC M 1280
HIT-S sleeves
Diameter length (mm) Material Packaging contents Ordering designation Item no.
10 10 10 10 10
Meter-long sleeves
Diameter length (mm) Material Packaging contents Ordering designation Item no.
50 50 25
10 10 10
10
65
HIT-S 12 A
20
Hilti HIT-A M 6/ 65
00049767
12
50
20
HIT-S 12 l
00049766
12
50
20
HIT-S 12 A
00049765
275
Anchor Systems
Accessories
Blow out pump Brush 13 mm dia. with grip Brush 18 mm dia. with grip Brush 28 mm dia. with grip Brush 18 mm dia. with thread rod connection Brush 28 mm dia. with thread rod connection Brush 38 mm dia. with thread rod connection Brush 18 mm dia. with thread rod connection Brush extension with grip and thread connection Brush extension with thread connection (both sides) Overhead holder Overhead holder Overhead holder Overhead holder Drip guard
Blow out pump Brush 13 mm dia. HG Brush 18 mm dia. HG Brush 28 mm dia. HG Brush 18 mm dia. GA Brush 28 mm dia. GA Brush 38 mm dia. GA Brush 50 mm dia. GA Hilti HIT-Z10 M8 Hilti HIT-Z10 M10 Hilti HIT-Z10 M12 Hilti HIT-Z10 M16 Hilti HIT-Z8
Ordering designation
00060579 00229133 00229134 00229135 00229136 00229137 00229673 00229674 00229138 00238727 00068170 00068171 00068172 00068173 00068165
Item no.
The purpose of this repulsion plug is to prevent the formation of the air bubbles inside the hole. The repulsion piston is attached to the hose and placed at the bottom of the hole, as the resin is injected it is pushed up the hole.
Ordering designation Item no.
B-UP plug HIT SZ 8 B-UP plug HIT SZ 10 B-UP plug HIT SZ 12 B-UP plug HIT SZ 14 B-UP plug HIT SZ 16 B-UP plug HIT SZ 20 B-UP plug HIT SZ 25
HIT-RB 8 round brush HIT-RB 10 round brush HIT-RB 12 round brush HIT-RB 14 round brush HIT-RB 16 round brush HIT-RB 20 round brush HIT-RB 25 round brush Extension for round brushes
s 00263437 s 00263439
Accessories
Ordering designation Item no.
PE-extension (9/1000) HIT-HY mixer extension (30cm) Mixer extension HIT-EXD 16/700
s PLEASE ASK FOR DELIVERY DETAILS. For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
276
Anchor Systems
Features n Exceptional load capacity loads comparable to cast in suitable for tensile zone / dynamic loading n Simple installation no diamond drilling / cutting equipment n Small edge distance and spacing
HDA-TF / HDA-PF
n Steelgrade 8.8, sherardised to min. 53 mic. Fastenings in damp conditions, e.g. in basements, cellars, shafts, etc. n M10 M16
HDA-TR / HDA-PR
n A4-80 stainless steel anchor rod n M10 M16 Fastenings outside exposed to long lasting condensation,e.g. tunnels, underground garages / parking lots, noisebarriers, bridge connections, etc.
1. Drill the hole with the stop drill bit and blow out the dust with a pump.
2. Using the setting tool mounted on a hammer drill, set the anchor until the setting mark on the anchor rod becomes visible.
hef
tfix dh
Technical data: HDA-P, HDA-T, HDA-PR, HDA-TR Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete Cracked concrete
HDA-P HDA-T HDA-PR HDA-TR Anchor size Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec M10 21.9 12.6 21.9 30.9 20.5 12.4 20.5 38.1 M12 31.9 17.1 31.9 38.1 29.9 18.3 29.9 46.7 M16 60.0 35.4 60.0 66.6 56.3 33.9 56.3 81.8 M20 91.1 56.0 91.1 100.0 M10 11.9 12.6 11.9 30.9 11.9 12.4 11.9 38.1 M12 16.7 17.1 16.7 38.1 16.7 18.3 16.7 46.7 M16 35.7 35.4 35.7 66.6 35.7 33.9 35.7 81.8 M20 45.3 56.0 45.3 100.0
do
Tinst SW
tfix dh
do
Tinst SW
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
277
Anchor Systems
Zivilschutz
20 21 20 107 30 23 22 135 50 23 22 135 40 32 30 203 60 32 30 203 50 40 37 266 100 40 37 266 * Please ask for delivery details.
17 19 19 24 24 30 30
12 8 8 4 4 2 2
HDA... 20-M10100/ 20 HDA... 22-M12125/ 30 HDA... 22-M12125/ 50 HDA... 30-M16190/ 40 HDA... 30-M16190/ 60 HDA... 37-M20250/ 50 HDA... 37-M20250/100
20 30 50 40 60 50 100
12 14 14 18 18 22 22
20 22 22 30 30 37 37
17 19 19 24 24 30 30
12 8 8 4 4 2 2
HDA... 20-M10100/ 20 HDA... 22-M12125/ 30 HDA... 22-M12125/ 50 HDA... 30-M16190/ 40 HDA... 30-M16190/ 60 HDA... 37-M20250/ 50 HDA... 37-M20250/100
Required tools
Anchor
Anchor size Packaging contents (pcs)
Setting tool
Packaging contents (pcs) Ordering designation Item no.
HDA-T/TF/TR 20-M10100/20 HDA-T/TF/TR 20-M10100/20 HDA-T/TF/TR 22-M12125/30 HDA-T/TF/TR 22-M12125/30 HDA-T/TF/TR 22-M12125/50 HDA-T/TF/TR 22-M12125/50 HDA-T/TF/TR 30-M16190/40 HDA-T/TF/TR 30-M16190/60 HDA-T 37-M20250/50 HDA-T 37-M20250/100 HDA-P/PF/PR 20-M10100/20 HDA-P/PF/PR 20-M10100/20 HDA-P/PF/PR 22-M12125/30 HDA-P/PF/PR 22-M12125/30 HDA-P/PF/PR 22-M12125/50 HDA-P/PF/PR 22-M12125/50 HDA-P/PF/PR 30-M16190/40 HDA-P/PF/PR 30-M16190/60 HDA-P 37-M20250/50 HDA-P 37-M20250/100
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
TE-C-HDA-B 20120 TE-Y-HDA-B 20120 TE-C-HDA-B 22155 TE-Y-HDA-B 22155 TE-C-HDA-B 22175 TE-Y-HDA-B 22175 TE-Y-HDA-B 30230 TE-Y-HDA-B 30250 TE-Y-HDA-B 37300 TE-Y-HDA-B 37350 TE-C-HDA-B 20100 TE-Y-HDA-B 20100 TE-C-HDA-B 22125 TE-Y-HDA-B 22125 TE-C-HDA-B 22125 TE-Y-HDA-B 22125 TE-Y-HDA-B 30190 TE-Y-HDA-B 30190 TE-Y-HDA-B 37250 TE-Y-HDA-B 37250
00332090 00237450 00332092 00237452 00332093 00237453 00332098 00332099 00339271 00339272 00332089 00237449 00332091 00237451 00332091 00237451 00332097 00332097 00339270 00339270
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
TE-C-HDA-ST 20-M10 TE-Y-HDA-ST 20-M10 TE-C-HDA-ST 22-M12 TE-Y-HDA-ST 22-M12 TE-C-HDA-ST 22-M12 TE-Y-HDA-ST 22-M12 TE-Y-HDA-ST 30-M16 TE-Y-HDA-ST 30-M16 TE-Y-HDA-ST 37-M20 TE-Y-HDA-ST 37-M20 TE-C-HDA-ST 20-M10 TE-Y-HDA-ST 20-M10 TE-C-HDA-ST 22-M12 TE-Y-HDA-ST 22-M12 TE-C-HDA-ST 22-M12 TE-Y-HDA-ST 22-M12 TE-Y-HDA-ST 30-M16 TE-Y-HDA-ST 30-M16 TE-Y-HDA-ST 37-M20 TE-Y-HDA-ST 37-M20
00331843 00287133 00331844 00287134 00331844 00287134 00331846 00331846 00339269 00339269 00331843 00287133 00331844 00287134 00331844 00287134 00331846 00331846 00339269 00339269
Item no.
Dynamic Set consisting of: injection washer, spherical washer, nut and locknut
Ordering designation Item no.
HDA-P 20-M10100/20 00331544 16 HDA-T 20-M10100/20 00331545 20 Dynamic Set M10 00369201 00331546 25.5 HDA-T 22-M12125/30 00331548 30 Dynamic Set M12 00369202 HDA-P 22-M12125/30 00331547 45.5 HDA-T 22-M12125/50 00331549 50 Dynamic Set M12 00369202 HDA-P 22-M12125/50 00331550 37 HDA-T 30-M16190/40 00331552 40 Dynamic Set M16 00369203 HDA-P 30-M16190/40 00331551 57 HDA-T 30-M16190/60 00331553 60 Dynamic Set M16 00369203 HDA-P 30-M16190/60 00339265 47 HDA-T 37-M20250/50 00339267 50 Dynamic Set M20 00369204 HDA-P 37-M20250/50 HDA-T 37-M20250/100 00339268 100 Dynamic Set M20 00369204 HDA-P 37-M20250/100 00339266 97 For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie Hilti. Outperform. Outlast.
278
Anchor Systems
nSteel strength 8.8 with rolled thread, zinc plating at least 5 microns thick n
Main features n Black plastic section no turning in hole during setting collapses for flush baseplate-to-surface fit n Choice of four head types (see next page for detail) n HSL-3-B, pictured requires no torque wrench for setting. The red cap shears off with correct torque, revealing a tamper-proof green seal n Embedment depth mark for easy setting n Extensive range of approvals and technical back-up
Technical data: HSL-3 Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete Cracked concrete
Anchor size Tensile N Rec Shear V Rec M8 11.1 17.8 M10 14.0 28.1 M12 17.2 41.0 M16 24.0 57.8 M20 33.5 81.1 M24 44.1 101.4 M8 4.8 17.8 M10 7.6 28.1 M12 12.3 41.0 M16 17.1 57.8 M20 24.0 81.1 M24 31.5 101.4
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
279
Anchor Systems
12 12 15 15 18 18 24 24 28 28 32 32 12 12 12 15 15 15 18 18 18 24 24 24 28 28 28 18 18 24 24 28 28 32 32
98 118 110 130 131 156 153 178 183 213 205 235 102 122 182 115 135 195 139 164 214 163 188 238 190 220 260 137 162 159 184 189 219 211 241
80 80 90 90 105 105 125 125 155 155 180 180 80 80 80 90 90 90 105 105 105 125 125 125 155 155 155 105 105 125 125 155 155 180 180
13 13 17 17 19 19 24 24 30 30 36 36 13 13 13 17 17 17 19 19 19 24 24 24 30 30 30 24 24 30 30 36 36 41 41
40 40 20 20 20 10 10 10 6 6 4 4 40 40 20 20 20 20 20 10 10 10 10 10 6 6 6 20 10 10 10 6 6 4 4
HSL-3 M 8/20 HSL-3 M 8/40 HSL-3 M 10/20 HSL-3 M 10/40 HSL-3 M 12/25 HSL-3 M 12/50 HSL-3 M 16/25 HSL-3 M 16/50 HSL-3 M 20/30 HSL-3 M 20/60 HSL-3 M 24/30 HSL-3 M 24/60 HSL-3-G M 8/20 HSL-3-G M 8/40 HSL-3-G M 8/100 HSL-3-G M 10/ 20 HSL-3-G M 10/ 40 HSL-3-G M 10/100 HSL-3-G M 12/ 25 HSL-3-G M 12/ 50 HSL-3-G M 12/100 HSL-3-G M 16/ 25 HSL-3-G M 16/ 50 HSL-3-G M 16/100 HSL-3-G M 20/ 30 HSL-3-G M 20/ 60 HSL-3-G M 20/100 HSL-3-B M 12/25 HSL-3-B M 12/50 HSL-3-B M 16/25 HSL-3-B M 16/50 HSL-3-B M 20/30 HSL-3-B M 20/60 HSL-3-B M 24/30 HSL-3-B M 24/60
00371775 00371776 00371778 00371779 00371781 00371782 00371784 00371785 00371787 00371788 00371790 00371791 00371793 00371794 00371829 00371796 00371797 00371830 00371799 00371800 00371831 00371802 00371803 00371832 00371805 00371806 00371833 00371808 00371809 00371811 00371812 00371814 00371815 00371817 00371818
Vrec (kN)
(kN)
Package contents
Ordering designation
Item no.
12 15 18
91 102 121
80 90 105
20 20 25
25 50 80
40 20 20
Nrec
Vrec
(kN)
(kN)
Package contents
Ordering designation
Item no.
15 18 24 28
20 20 25 25 30
13 17 19 24 30
25 40 80 120 200
40 20 20 10 6
HSLG-R M 8/20 HSLG-R M 10/20 HSLG-R M 12/25 HSLG-R M 16/25 HSLG-R M 20/30
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
280
Anchor Systems
Material Steel strength 8.8, zinc plated 5 microns thick n A4 stainless steel (material 1.4401 / AISI 316)
n
Tinst
Features n Anchor hole drilled as usual, without undercutting n Automatic undercutting by anchor when anchor sleeve is driven onto stud taper n Fire resistance
Technical data: HSC-I, HSC-IR, HSC-A, HSC-A Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete Cracked concrete
l
HSC-I
Tinst
do tfix
HSC-IR
h1
HSC-A HSC-A
Anchor size Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Anchor size Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec
M8x40 M10x50 M10x60 M12x60 M6x40 6.1 8.5 11.1 11.1 4.3 7.0 8.7 8.7 10.4 4.6 6.1 8.5 11.1 11.1 4.3 4.9 6.1 6.1 7.4 3.2 M8x40 M8x50 M10x40 M12x60 6.1 8.5 6.1 11.1 8.3 8.3 13.3 19.3 6.1 8.5 6.1 11.1 5.9 5.9 9.3 13.5
M8x40 M10x50 M0x50 M12x60 4.3 6.0 8.0 8.0 7.0 8.7 8.7 10.4 4.3 6.0 8.0 8.0 4.9 6.1 6.1 7.4 M8x40 M8x50 M10x40 M12x60 4.3 4.3 4.3 8.0 8.3 8.3 13.3 19.3 4.3 6.0 4.3 8.0 5.9 5.9 9.3 13.5
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
281
Anchor Systems
rec
rec
(kN)
(kN)
Package contents
Ordering designation
Item no.
14 14 16 18
46 56 46 68
15 15 20 20
13 13 17 19
A4 316
10 10 20 30
25 25 25 20
rec
rec
(kN)
(kN)
Package contents
Ordering designation
Item no.
14 14 16 18
46 56 46 68
15 15 20 20
13 13 17 19
10 20 10 30
25 25 25 20
rec
rec
(kN)
(kN)
Package contents
Ordering designation
Item no.
14 16 18 18 20
46 46 56 56 68
10 10 20 30 30
25 25 25 25 25
HSC-I M 640 HSC-I M 840 HSC-I M 1050 HSC-I M 1060 HSC-I M 1260
rec
rec
(kN)
(kN)
Package contents
Ordering designation
Item no.
14 16 18 18 20
46 46 56 56 68
10 10 20 30 30
25 25 25 25 25
7
For use in: TE 15 TE15-C l l l l l l TE 25 Ordering designation Item no.
HSC-A (R)
HSC-I (R)
14 14 16 18 18 20
TE-C HSC-B 1440 TE-C HSC-B 1450 TE-C HSC-B 1640 TE-C HSC-B 1850 TE-C HSC-B 1860 TE-C HSC-B 2060
M 8 M 10 M 12
M 6 M 8 M 10 M 12
282
Anchor Systems
VdS
G 4930030
EDELSTAHL
Stainless steel
ALLGEMEIN
BAUAUFSICHTLICH
ZUGE LASSEN
FM
Factory Manual
Versions offered: n HST zinc plated (min. 5 microns) n HST-R A4 stainless steel (DIN 1.4401 / AISI 316) n HST-HCR DIN 1.4529 high corrosion resistant Areas of application: Base material: concrete in the tensile and compression zone, hard natural stone n Fastening through in-place parts e. g. angles, tracks, channels, beams etc. n Special programme in HCR material: for applications where high corrosion resistance is required, like street tunnels or swimming pools (high concentration of chlorides)
n
Approvals: European technical approval (ETA) Option 1 for concrete in the tensile and compression zone (zinc plated M8M24, stainless M8M24) the anchor can therefore be used in all CE-countries. n German approval (DIBt) for material 1.4529 high corrosion resistant (HCR), diameters M8M16 n Fire resistance The anchor can be used where fire resistance is required (approved by the IBMB Germany all offered sizes and materials) n Shock approval Switzerland BZS for civil defence shelters all offered sizes and materials n Sprinkler systems approved by VDS and FM
n
Characteristics: n Embedment depth marked (black ring) to ensure that the fastening is done right on site. n Nut and washer pre-assembled for time saving on site n Approved for cracked concrete The anchor is approved for applications in the tensile zone of concrete according to the European building codes (CE) and can therefore be used in the tensile and compression zone.
The small permitted edge and spacing distances allow design flexibility, even with narrow structural members.
n Cold-formed
Due to the manufacturing process (coldforming technology), the steel material remains ductile. The result is an anchor which allows alignments without breaking.
283
Anchor Systems
Technical data: HST, HST-R Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete Cracked concrete HST
Anchor size Tensile N Rec Shear V Rec Anchor size Tensile N Rec Shear V Rec M8 3.6 7.4 M8 4.3 7.4 M10 7.6 11.4 M10 7.6 11.4 M12 9.5 17.1 M12 9.5 17.1 M16 16.7 28.6 M16 16.6 27.5 M20 23.8 29.6 M20 23.8 39.7 M24 28.6 44.8 M24 28.6 57.1 M8 2.0 7.4 M8 2.4 7.4 M10 4.3 11.4 M10 4.3 11.4 M12 5.7 17.1 M12 5.7 17.1 M16 9.5 28.6 M16 11.9 27.5 M20 14.3 29.6 M20 14.3 39.7 M24 19.0 44.8 M24 19.0 57.1
HST-R
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
EDELSTAHL
Stainless steel
8 75 8 95 8 115 10 90 10 110 10 130 12 115 12 145 12 185 12 215 12 235 12 255 16 140 16 165 16 215 16 255 16 295 20 170 20 200 20 270 24 200 24 230 * HST-R packaging contents: 50
Hole dia., (do) mm Anchor length, (l) mm
100 * 100 * 50 50 50 25 25 25 25 25 25 25 12 12 12 12 12 5 5 5 5 5
HST M 8/ 10 HST M 8/ 30 HST M 8/ 50 HST M10/ 10 HST M10/ 30 HST M10/ 50 HST M12/ 20 HST M12/ 50 HST M12/ 90 HST M12/120 HST M12/140 HST M12/160 HST M16/ 25 HST M16/ 50 HST M16/100 HST M16/140 HST M16/180 HST M20/ 30 HST M20/ 60 HST M20/130 HST M24/ 30 HST M24/ 60
00371581 00371582 00371583 00371584 00371585 00371586 00371587 00371588 00371589 00371590 00371591 00371592 00371593 00371594 00371595 00371596 00371597 00371598 00371599 00371600 00371601 00371602
00376039 00376041 00376042 00376043 00376044 00376045 00376047 00376048 00376049 00376050 00376051 00376052 00376053 00376054 00376055 00376056 00376057 00376058 00376059
HST-HCR, stainless steel (HCR, high corrosion resistant material as per DIN 1.4529)
Max. fastenable thickness, (tfix) mm Packaging contents (pcs) Ordering designation Item no. Stainless (HCR 1.4529)
10 30 10 30 20 50 25 50
20 20 20 20 10 10 10 10
HST-HCR M 8/10 HST-HCR M 8/30 HST-HCR M10/10 HST-HCR M10/30 HST-HCR M12/20 HST-HCR M12/50 HST-HCR M16/25 HST-HCR M16/50
Ordering designation
Item no.
TE-C TE-C
150 300
1 1
00337918 00337919
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
284
Anchor Systems
EDELSTAHL
Stainless steel
Versions offered: n HSA zinc plated (min. 5 microns) n HSA-F hot dipped galvanized (ISO 1461, 45 microns) n HSA-R A4 stainless steel (DIN 1.4401 / AISI 316) Areas of application: n Base material: concrete in the compression zone n Versatile fastening through in-place parts like wood beams, metal sections, columns, brackets, etc. n Offered in a variety of length (to fit for every specific thickness of the fastening part) and materials (to match specific corrosion requirements). Approvals: n European technical approval (ETA) Option 8 for concrete in the compression zone (zinc plated M6M20, stainless M6M12) the anchor can therefore be used in all CE-countries. n Fire resistance The anchor can be used where fire resistance proof is required (for the zinc plated and stainless version approved by the IBMB Germany) Characteristics: n Long thread, offering flexibility for special applications n Two embedment depths marked, to ensure that the fastening is done right on site. Standard embedment: blue ring Reduced embedment: thread end n Nut and washer pre-assembled for time saving on site Technical data: HSA, HSA-R, HSA-F - Uncracked concrete Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Standard embedment depth Reduced embedment depth HSA
Anchor size Tensile N Rec Shear V Rec M6 2.4 2.9 M6 2.4 2.9 M6 2.4 2.9 M8 M10 M12 M16 Standard anchorage depth 5.7 7.6 11.9 18.5 4.4 7.1 10.2 19.1 M8 M10 M12 M16 Standard anchorage depth 4.8 4.1 8.5 15.4 5.2 8.1 11.9 22.4 M8 M10 M12 M16 Standard anchorage depth 5.7 7.6 11.9 18.5 4.4 7.1 10.2 19.1 M20 25.1 29.8 M20 17.5 35.0 M20 25.1 29.8 M6 2.0 2.9 M6 1.4 2.8 M6 2.0 2.9 M8 M10 M12 M16 Standard anchorage depth 4.3 5.7 8.5 12.3 4.4 7.1 10.2 19.1 M8 M10 M12 M16 Standard anchorage depth 3.0 4.1 8.5 9.1 5.2 8.1 11.9 22.4 M8 M10 M12 M16 Standard anchorage depth 4.3 5.7 8.5 12.3 4.4 7.1 10.2 191 M20 16.5 29.8 M20 13.2 35.0 M20 16.5 29.8
n Head
marking
n Ductility of the
steel
n Two embedment
depths
HSA-R
Anchor size Tensile N Rec Shear V Rec
HSA-F
Anchor size Tensile N Rec Shear V Rec
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
285
Anchor Systems
6 6 6 6 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 12 12 12 16 16 16 16 16 20 20
50 65 85 100 57 75 92 115 137 68 90 108 120 140 80 100 120 150 180 220 240 300 100 120 140 190 240 125 170
A C D E B C E G H C E F G I D E G I L O P S E G I L P G K
HSA M 6 50/ / 5 HSA M 6 65/ 10/ 20 HSA M 6 85/ 30/ 40 HSA M 6100/ 45/ 55 HSA M 8 57/ / 5 HSA M 8 75/ 10/ 23 HSA M 8 92/ 27/ 40 HSA M 8115/ 50/ 63 HSA M 8137/ 72/ 85 HSA M10 68/ / 5 HSA M10 90/ 20/ 25 HSA M10108/ 37/ 45 HSA M10120/ 50/ 57 HSA M10140/ 70/ 77 HSA M12 80/ / 5 HSA M12100/ 5/ 25 HSA M12120/ 25/ 45 HSA M12150/ 55/ 75 HSA M12180/ 85/105 HSA M12220/125/145 HSA M12240/145/165 HSA M12300/205/225 HSA M16100/ / 5 HSA M16120/ 5/ 25 HSA M16140/ 25/ 45 HSA M16190/ 75/ 95 HSA M16240/125/145 HSA M20125/ / 10 HSA M20170/ 30/ 55
00255830 00255831 00255832 00255833 00255834 00255835 00255836 00255837 00255838 00255839 00255840 00255841 00255842 00255843 00255844 00255845 00255846 00255847 00255848 00255849 00255850 00255851 00255852 00255853 00255854 00255855 00255856 00255857 00255858
00338260 00337121 00337122 00337123 00337124 00337125 00337126 00337127 00337128 00337129 00337130 00337131 00337132 00337133 00338261 00337134 00337135 00337136 00337137
00332183 00332184 00332185 00332186 00332187 00332188 00332189 00332190 00332191 00332192 00332193 00332194 00332195 00337116 00337117 00337118 00337119 00337120
Packaging contents
Ordering designation
Item no.
TE-C TE-C
150 300
1 1
00337918 00337919
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
286
Anchor Systems
ALLGEMEIN
BAUAUFSICHTLICH
ZUGE LASSEN
Versions offered: n HKD-S: zinc plated (min. 8 microns) n HKD-SR: A4 stainless steel (DIN 17440)
n
G 4930030
Areas of application: Base material: concrete in the compression zone, hard natural stone n Fastening medium loads with bolts or threaded rods n Optimum solution for serial fastenings in suspended ceilings, pipe suspensions, machine fixing etc. n Ideal for setting in the undersides of cavity ceilings n Ideal for setting into Bison precast hollow units Approvals: n Fire resistance: The anchor can be used where fire resistance is required Low-strength base High-strength base Characteristics:
material (fully set) material (fully set)
Flared end For accurate setting flush with the surface, independent of hole depth.
Full expansion Cone design permits the full expansion of the anchor in both low-strength and high-strength material. No thread damage when hammering the anchor into the hole. Easy setting.
Visual verification Visual verification of full expansion. The setting tool leaves a mark on the flared end that indicates proper expansion. Increased security.
Manual setting tool With ergonomic hand guard for better grip, size gauge for quick check that the right tool is used and polygonal top that protects from injuries.
BAUAUFSICHTLICH
ZUGE LASSEN
SOCOTEC
VdS
G 4930030
Versions offered: n HKD-E: zinc plated (min. 8 microns) Approvals: n French approval (Socotec): For fastenings in the compression zone n Fire resistance: The anchor can be used where fire resistance is required. Characteristics:
No flared end No flared end for easy setting in greater depth.
Areas of application: n Base material: concrete in the compression zone, hard natural stone n Fastening medium loads with bolts or threaded rods n Ideal for through fastening applications
Areas of application: n Base material: concrete in the compression zone, hard natural stone n For fastening drilling rig baseplates Characteristics: Outside diameter of 16 mm for higher holding power n Higher torque applicable compared to standard flush anchors n No flared end for easy setting in greater depth n Cone design permits the full expansion of the anchor in both lowstrength and high-strength material. No thread damage when hammering the anchor into the hole. Easy setting.
n
287
Anchor Systems
Technical data: HKD-S Recommended load, L rec (kN): f ck,cube = 25 N/mm2 HKD-S
Anchor size Tensile N Rec Shear V Rec M6x25 2.1 2.1 M6x30 3.3 2.1 M8x30 3.3 3.9 M8x40 M10x30 M10x40 M12x50 M16x65 M20x80 3.6 3.3 5.1 7.1 12.6 17.2 3.9 4.2 4.6 8.1 12.5 19.9
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
HKD-S M 625 100 HKD-S M 8301) 100 HKD-S M 840 50 HKD-S M10301) 100 HKD-S M1040 50 HKD-S M1250 50 HKD-S M1665 25 HKD-S M2080 25
100 100 50 50 25 25
10 12 15 20
30 40 50 65
33 43 53 70
100 50 50 25
M12
16
50
53
HKD-D M1250 HSD-M mechanical setting tool HSD-M M 625 HSD-M M 830 HSD-M M 840 HSD-M M1030 HSD-M M1040 HSD-M M1250 HSD-M M1665 HSD-M M2080
50
00252961
Item no.
HKD M 625 HKD M 830 HKD M 840 HKD M1030 HKD M1040 HKD M1250 HKD M1665 HKD M2080 Note: HSD-M M6 to M12: TE-C connection HSD-M M16 to M20: TE-Y connection
HSD-G M 625 HSD-G M 830 HSD-G M 840 HSD-G M1030 HSD-G M1040 HSD-G M1250 HSD-G M1665 HSD-G M2080
HSD-G
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
TE15
HSD-M
288
Anchor Systems
Versions offered: zinc plated (min. 5 microns) n HLC: bolt version n HLC-H: with screw n HLC-F: with flat countersunk head n HLC-T: with tie wire head n HLC-EO: with open eyelet n HLC-EC: with closed eyelet Areas of application: Base material: concrete in the compression zone, solid and thick walled hollow bricks, sand lime block and solid block n Fastening through a wide variety of in-place parts without stringent requirements like hand rails, angles, switchboxes etc. n Ideal for temporary fastenings such as forming braces, jacks etc. Easily removable
n
Approvals: Socotec approval: For fastenings in the compression zone n Fire resistance: The anchor can be used where fire resistance is required
n
Characteristics: n Ingenious midriff / Practical imprint Ingenious midriff bulged in the middle with triangular diamond shaped openings. This prevents the anchor from turning in its hole or dropping out when fastening overhead. Practical imprint on the sleeve that shows the right drill to use n Wide expansion Wide expansion of the anchor that ensures good holding power in hollow materials
Easily removable
Technical data: HLC Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete
Anchor size Tensile N Rec Shear V Rec M5 0.5 0.8 M6 1.0 1.8 M8 1.5 3.2 M10 2.0 5.2 M12 3.0 6.3 M16 4.0 7.5
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
M5 M6 M6 M8 M10 M10
6.5 8 8 10 12 12
30 40 40 47 56 45
20 12 37 28 37 62
289
Anchor Systems
Bucket packaging
Item no.
/ / 1 / 8 8 8 8 10 10 10 10 10 12 12 12 16 16 16 20 20 20
1
4
4 4
30 30 30 40 40 40 40 47 47 47 47 47 56 56 56 72 72 72 85 85 85
5 5 5 8 8 8 8 25 25 25 25 25 40 40 40 50 50 50 80 80 80
5 20 40 12 27 42 57 8 18 28 48 68 17 37 62 12 52 92 25 60 95
0.5 0.5 0.5 1.0 1.0 1.0 1.0 1.5 1.5 1.5 1.5 1.5 2.0 2.0 2.0 3.0 3.0 3.0 4.0 4.0 4.0
0.8 0.8 0.8 1.8 1.8 1.8 1.8 3.2 3.2 3.2 3.2 3.2 5.2 5.2 5.2 6.3 6.3 6.3 7.5 7.5 7.5
HLC 6.525/5 HLC 6.540/20 HLC 6.560/40 HLC 8 40/12 HLC 8 55/27 HLC 8 70/42 HLC 8 85/57 HLC 10 40/ 8 HLC 10 50/18 HLC 10 60/28 HLC 10 80/48 HLC 10100/68 HLC 12 55/17 HLC 12 75/37 HLC 12100/62 HLC 16 60/12 HLC 16100/52 HLC 16140/92 HLC 20 80/25 HLC 20115/60 HLC 20150/95
00230768 00230769 00230770 00230771 00230772 00230773 00230774 00230775 00230776 00230777 00230778 00230779 00230780 00230781 00230782 00230783 00230784 00230785 00230786 00230787 00230788
8 8 8 10 10 10 12 12 12 16 16 16
40 40 40 47 47 47 56 56 56 72 72 72
8 8 8 25 25 25 40 40 40 50 50 50
12 27 42 8 28 48 17 37 62 12 52 92
1.0 1.0 1.0 1.5 1.5 1.5 2.0 2.0 2.0 3.0 3.0 3.0
1.8 1.8 1.8 3.2 3.2 3.2 5.2 5.2 5.2 6.3 6.3 6.3
HLC 8 40/12-H HLC 8 55/27-H HLC 8 70/42-H HLC 10 40/ 8-H HLC 10 60/28-H HLC 10 80/48-H HLC 12 55/17-H HLC 12 75/37-H HLC 12100/62-H HLC 16 60/12-H HLC 16100/52-H HLC 16140/92-H
00256956 00230791 00230792 00256957 00230793 00230794 00256958 00230795 00230796 00334124 00334125 00334127
Eyebolt M6 M6
HLC EO
M5 M5 M5 M5 M6 M6 M8 M8
8 8 10 10
50 65 88 110 65 96 91 115
30 30 30 30 40 40 47 47
5 5 5 5 8 8 25 25
25 40 48 68 40 57 57 68
HLC 6.5 x 45 F HLC 6.5 x 60 F HLC 6.5 x 80 F HLC 6.5 x 100 F HLC 8 x 60 F HLC 8 x 90 F HLC 10 x 85 F HLC 10 x 105 F
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
290
Anchor Systems
HB Hilti Bolt
Features: n An all iron/steel high expansion bolt for all types of general purpose fastening n Particularly for fastening to masonry and brickwork n Material sleeve: malleable iron n Material bolts: BS 6104 grade 5.6, zinc plated to 5m
Sleeve only
Hole dia. (mm) Hole depth (mm) Max. thick. fastened Nrec kN Vrec kN Max. tight torque Nm Box contents Ordering designation Item no.
12 50 N/A 100 14 55 N/A 100 16 65 N/A 100 20 85 N/A 25 25 105 N/A 10 Load and tightening torque are dependent on bolt grade used. Bolt assembly
Hole dia. (mm) Hole depth (mm) Max. thick. fastened Nrec kN Vrec kN Max. tight torque Nm Box contents
HB M 6 sleeve only HB M 8 sleeve only HB M 10 sleeve only HB M 12 sleeve only HB M 16 sleeve only
HB
Ordering designation
Item no.
12 12 14 14 16 16 20 20 20
50 50 55 55 65 65 85 85 85
10 25 10 25 10 25 10 25 40
2.8 2.1 2.8 2.1 4.4 3.9 4.4 3.9 6.1 7.7 6.1 7.7 10.8 10.4 10.8 10.4 10.8 10.4
50 50 50 50 50 25 20 10 10
HB-L
Stud assembly
Hole dia. (mm) Hole depth (mm) Max. thick. fastened Nrec kN Vrec kN Max. tight torque Nm Box contents Ordering designation Item no.
12 12 14 14 16 16 20 20 25 25
50 50 55 55 65 65 85 85 105 105
10 25 10 25 30 60 30 70 30 75
2.8 2.8 4.4 4.4 6.1 6.1 10.8 10.8 15.1 15.1
2.1 2.1 3.9 3.9 7.7 7.7 10.4 10.4 19.7 19.7
6.5 6.5 16.0 16.0 28.0 28.0 51.0 51.0 122.0 122.0
50 50 50 50 50 25 25 20 10 10
HB M 6/10P HB M 6/25P HB M 8/10P HB M 8/25P HB M 10/30P HB M 10/60P HB M 12/30P HB M 12/75P HB M 16/30P HB M 16/75P
00049745 00049746 00049747 00049748 00049749 00049750 00049751 00049752 00049753 00049754
HB-P
Nrec = Tensile working load (static), in 30 N/mm2 concrete. Vrec = Shear working load (static), in 30 N/mm2 concrete. Technical data: HB Bolt Recommended load, L rec (kN): concrete f ck,cube = 30 N/mm2 Uncracked concrete
Anchor size Tensile N Rec Shear V Rec NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions adjacent. Please consult Hilti Fastening Technology Manual for specific design requirements. M6 2.8 2.1 M8 4.4 3.9 M10 6.1 7.7 M12 10.8 10.4 M16 15.1 19.7
Guide recommended load, L rec (kN): solid brickwork,27 N/mm2 Uncracked concrete
Anchor size Tensile N Rec Shear V Rec M6 2.8 2.1 M8 4.4 3.9 M10 6.1 7.7 M12 10.8 10.4 M16 15.1 19.7
291
Anchor Systems
Basic loading data (for a single anchor) All data in this section applies to cracked and non-cracked concrete: as specified in the table no edge distance, spacing and other influences correct setting
HUS-H
HUS-H 10.5 screw anchor with hexagon head 13 mm AF, 17.5 mm washer dia.
Drill bit nom. dia., d0 (mm) Anchor length, ls (mm) Embedment depth, Packaging standard minimum contents hnom (mm) hnom (mm) (pcs) Ordering designation Item no.
8 8 8 8 8 8 8
60 60 60 60 60 60
50 50 50 50 50 50 50
50 50 50 50 50 50 50
HUS-H 10.555//5 HUS-H 10.565/5/15 HUS-H 10.575/15/25 HUS-H 10.590/30/40 HUS-H 10.5110/50/60 HUS-H 10.5130/70/80 HUS-H 10.5150/90/100
HUS-H 12.5 screw anchor with hexagon head 15 mm AF, 20.5 mm washer dia.
10 10 10 10 10 10 10 65 75 85 100 120 140 160 70 70 70 70 70 70 60 60 60 60 60 60 60 50 50 50 50 50 50 50 HUS-H 12.565//5 HUS-H 12.575/5/15 HUS-H 12.585/15/25 HUS-H 12.5100/30/40 HUS-H 12.5120/50/60 HUS-H 12.5140/70/80 HUS-H 12.5160/90/100 00335089 00335090 00335091 00335092 00335093 00335094 00335095
7
SI 100 impact screwdriver
The tool to drive HUS-H screw anchors into concrete Technical data Voltage: Nominal power: Torque: Speed: Weight: Chuck: SI 100 110 V 470 W 100 Nm 0-2200 r.p.m. 2.5 kg 1/20 socket
HUS-H 16.5 screw anchor with hexagon head 21 mm AF, 30 mm washer dia.
14 14 14 14 80 115 135 160 90 90 90 90 70 70 70 70 16 16 16 16 HUS-H 16.580///10 HUS-H 16.5115/5/25/45 HUS-H 16.5135/25/45/65 HUS-H 16.5160/50/70/90 00377989 00377990 00377991 00377992
Technical data: HUS-H Recommended load, L rec (kN): concrete f ck,cube = 25 N/mm2 Uncracked concrete Cracked concrete
Anchor size hmon Tensile N Rec Shear V Rec 10.5
60
10.5
50
12.5
70
12.5
60
16.5
110
16.5
90
16.5
70
10.5
60
10.5
50
12.5
70
12.5
60
16.5
90
4.5 7.3
3.3 7.3
5.9 10.3
4.8 10.3
20.0 27.0
16.2 26.2
10.4 24.6
2.5 7.3
1.5 7.3
3.5 10.3
2.5 10.3
6.8 26.2
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
292
Anchor Systems
HUS-HF 12.5 screw anchor with hexagon head 15 mm AF, 20.5 mm washer dia.
Drill bit nom. dia., d0 (mm) Anchor length, ls (mm) Embedment depth, deep standard minimum hnom (mm) hnom (mm) hnom (mm) Packaging contents (pcs) Ordering designation Item no.
10 10 10 10 10
65 75 85 100 120
70 70 70 70
60 60 60 60 60
50 50 50 50 50
HUS-HF 12.565//5 HUS-HF 12.575/5/15 HUS-HF 12.585/15/25 HUS-HF 12.5100/30/40 HUS-HF 12.5120/50/60
HUS-HF 16.5 screw anchor with hexagon head 21 mm AF, 30 mm washer dia.
Drill bit nom. dia., d0 (mm) Anchor length, ls (mm) Embedment depth, deep standard minimum hnom (mm) hnom (mm) hnom (mm) Packaging contents (pcs) Ordering designation Item no.
14 14
Description
80 115
110 110
90 90
70 70
16 16
267763 267764
Item no.
SI 100 impact screwdriver and socket wrench inserts SI100 impact screwdriver in toolbox Accessories
Description Length (mm) Packaging contents (pcs) Ordering designation Item no.
1
2
SI100
334202
Socket wrench insert, 13 mm AF, long with magnet Socket wrench insert, 15 mm AF, long with magnet Socket wrench insert, 21 mm AF, short with magnet
2
77 77 40 40 40 40
1 1 1 1 1 1 1 1 1
(Drive: 1/ square, Driven: hexagon 15 AF/13 AF), especially for installing Hilti MQ installation channel system components
Socket wrench insert, 13 mm AF, short Socket wrench insert, 15 mm AF, short Socket wrench insert, 21 mm AF, short
(Drive: 1/ square, Driven: hexagon 15 AF/13 AF)
2
Extension S-V125 1/ 1/
2
293
Anchor Systems
Solid brick
min. 50 mm 6 mm 6,2 mm
Concrete
min. 40 mm 6 mm 6,2 mm
T40
min. 60 mm
min. 40 mm
min. 30 mm
Max. fastenable thickness (mm) Concrete Solid brick (Hilti rec.) Sand-lime brick
7
Hollow brick Gas/aerated concrete Screw length (mm) Package contents Ordering designation Item no.
100 100 100 100 100 100 100 100 100 100 100
HUS 7.5 35 HUS 7.5 45 HUS 7.5 60 HUS 7.5 80 HUS 7.5100 HUS 7.5120 HUS 7.5140 HUS 7.5160 HUS 7.5180 HUS 7.5200 HUS 7.5220
00383047 00383048 00383049 00381401 00381402 00381403 00381404 00381405 00383050 00383051 00383052
HUS-A 7.5 screw anchor with hexagon head 13 mm AF, 18 mm washer dia.
Max. fastenable thickness (mm) Concrete Solid brick* (Hilti rec.) Sand-lime brick Hollow brick* Gas/aerated concrete Screw length (mm) Package contents Ordering designation Item no.
HUS-A
15 30 15 30
5 20 5 20
0 0 0 0
45 65 45 65
45 M8 65 M8 45 M10 65 M10
s PLEASE ASK FOR DELIVERY DETAILS. For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie
294
Anchor Systems
HUS-H 7.5 screw anchor with hexagon head 13 mm AF, 18 washer diameter with T40 drive recess
Use of HUS-H n Fastening light-duty installation channels, light-duty steel angles, mechanical installation components and parts for interior panelling or cladding Features n A matched system of screw anchor and screwdriver n Screw driven straight into base material without using an anchor n Small hole diameter; high holding power n Forged-on washer and hexagon head for optimised guidance when screwdriving n Minimal expansion forces in base material HUS-H HUS-H
HUS-H 7.5 screw anchor with hexagon head 13 mm AF, 18 mm washer dia.
Max. fastenable thickness (mm) Concrete Solid brick (Hilti rec.) Sand-lime brick Hollow brick Gas/aerated concrete Screw length (mm) Package contents Ordering designation Item no.
5 15 30 50 70 90
0 5 20 40 60 80
0 0 0 20 40 60
35 45 60 80 100 120
HUS-H 7.5 35 HUS-H 7.5 45 HUS-H 7.5 60 HUS-H 7.5 80 HUS-H 7.5100 HUS-H 7.5120
00227351 00227338
Features nA tangential rotary impact action, thus the high torque (reaction force) is hardly felt at the operators hand. Uses n Driving the 7.5-mm-diameter HUS screw in concrete, brick, sand-lime brick and gas concrete n Driving 8 mm diameter screws into HRD anchors n Driving 8 mm diameter screws into metal and plastic anchors n Driving 8 mm diameter screws into brick and sand-lime brick n Driving 8 mm diameter woodscrews
200
1
8
TKI-S 6/35
Ordering designation
s 00220687
Item no.
Driven end: 1/ hex as per DIN 3126 / E 6.3, Driving end: 3/ square
Description Length (mm) Package contents
Socket
Description
Adaptor
50
1
4
1
Package contents
S-BH 3/ 50
8
00236339
Item no.
S-BH 3/ 50
8
Driven end: / hex, Driving end: 13 AF (Hex) Socket (for HUS-H and HUS-A) Socket (thin walled socket for ML channel)
4
4
Length (mm)
Ordering designation
50 50
Length (mm)
1 1
4
00318364 00305096
Item no.
S-NSD13L
Driven end: 1/ hex as per DIN 3126 / E 6.3, Driving end: 1/ hex as per DIN 3126 / C 6.3
Package contents
Accessories
Description
Bit holder, steel, short, magnetic Bit holder, steel, long, magnetic Bit holder with locking sleeve, magnetic Bit
50 75 50
1 1 1
Package contents
10
S-B TXI 40
00258132
S-BTXI40
s PLEASE ASK FOR DELIVERY DETAILS. www.hilti.co.uk | 0800 886 100 www.hilti.ie | 1850 287 387
295
Anchor Systems
Package contents
Ordering designation
Item no.
10 10 10 10 10
Driven end: 1/ hex as per DIN 3126 / E 6.3, Driving end: 1/ hex as per DIN 3126 / C 6.3
4
Description
Length (mm)
Package contents
Ordering designation
Item no.
Bit holder, steel, short, magnetic Bit holder, steel, long, magnetic Bit holder with locking sleeve, magnetic
50 75 50
1 1 1
Package contents
S-BH50M / S-BH75M
Accessories
Description
S-BHU50M
Bit
1 10
Box Qty.
Posidrive 3 Posidrive 3
00080213 00257620
Item no.
Cover caps
Description
Cover cap (flat) HTK-S15 for HT10/HPF. White 100 Cover cap (overlapping) HTK-SU17 for HT10. White 100 Cover cap (flat) HTK-S15 for HT10/HPF. Dk. Brown 100 Cover cap (overlapping) HTK-SU17 for HT10. Dk. Brown 100
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie
296
Anchor Systems
Setting operations:
HPF/2
Anchor/ hole dia. (mm) Anchor length (mm) Min. embedment depth (mm) Max. thickness fastened (mm) Cap dia. (mm) Nrec (kN) Vrec (kN) Box contents Ordering designation Item no.
8 8 10 10 10 10 10
50 50 50 50 50 50 50
50 90 25 50 70 90 115
HPF/2 8 x 100/50 HPF/2 8 x 140/90 HPF/2 10 x 75/25 HPF/2 10 x 100/50 HPF/2 10 x 120/70 HPF/2 10 x 140/90 HPF/2 10 x 165/115
Driven end: 1/ hex as per DIN 3126 / E 6.3, Driving end: 1/ hex as per DIN 3126 / C 6.3
4
Description
Length (mm)
Package contents
Ordering designation
Item no.
Bit holder, steel, short, magnetic Bit holder, steel, long, magnetic Bit holder with locking sleeve, magnetic
50 75 50
1 1 1
Package contents
S-BH50M / S-BH75M
Accessories
Description
S-BHU50M
Bit (Philips)
Philips No 3
00080503
297
Anchor Systems
Use
Material
Features n Smooth surface for a larger contact area with greater friction and higher holding power n Insertion detent to avoid premature expansion n Preassembled with screw to fasten parts 30 mm thick and more. Technical data: HRD-S Recommended load, L rec (kN)
Anchor size Concrete f cc 20 N/mm2 Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec Tensile N Rec Shear V Rec
Solid brick f cc 20 N/mm2 Sand-lime block f cc 12 N/mm2 NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions adjacent. Please consult Hilti Fastening Technology Manual for specific design requirements. Hollow block f cc 4 N/mm2 Sand-lime hollow block f cc 6 N/mm2 Aerated concrete f cc 6 N/mm2
HRD-SGT
HRD-S-10 1.4 1.8 0.8 0.8 1.0 1.0 0.25 0.25 1.0 1.0 0.4 0.5
HRD-SGT Version: anchor body and T40-head screw, steel zinc plated to 5 microns, chromated
Hole dia., d (mm)
o
7
Package contents Ordering designation Item no.
10 10 10 10 10 10
60 60 60 60 60 60
10 30 50 70 90 110 10 50 90
50 50 50 50 50 50 50 50 50
50 50 50 50 50 50 50 50 50
HRD-SGT 10 60/ 10 HRD-SGT 10 80/ 30 HRD-SGT 10100/ 50 HRD-SGT 10120/ 70 HRD-SGT 10140/ 90 HRD-SGT 10160/110 HRD-SRT 10 60/ 50 HRD-SRT 10100/ 50 HRD-SRT 10140/ 90
HRD-SGS Version: with hexagon-head screw 13 mm across flats, steel zinc plated to 5 microns, chromated
Hole dia., d (mm)
o
Package contents
Ordering designation
Item no.
10 10 10 10 10 10
60 60 60 60 60 60
10 30 50 70 90 110 10 30 50 90
50 50 50 50 50 50 50 50 50 50
50 50 50 50 50 50 50 50 50 50
HRD-SGS 10 60/ 10 HRD-SGS 10 80/ 30 HRD-SGS 10100/ 50 HRD-SGS 10120/ 70 HRD-SGS 10140/ 90 HRD-SGS 10160/110 HRD-SRS 10 60/ HRD-SRS 10 80/ HRD-SRS 10100/ HRD-SRS 10140/ 10 30 50 90
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
298
Anchor Systems
Technical data: HRD-U Recommended load, L rec (kN) Features n For use in hollow and solid base material n High holding power, thus fewer fastenings, less installation work and lower costs n Innovative screw design for a better hold (HRD-U8 only)
Anchor size Concrete f cc 20 N/mm2
Solid brick f cc 20 N/mm2 Sand-lime block f cc 12 N/mm2 Hollow block f cc 4 N/mm2 Sand-lime hollow block f cc 6 N/mm2 Aerated concrete f cc 6 N/mm2
HRD-U-8 Tensile N Rec 1.0 3.9 Shear V Rec Tensile N Rec 0.4 Shear V Rec 0.4 Tensile N Rec 0.5 Shear V Rec 0.5 Tensile N Rec Shear V Rec - Tensile N Rec Shear V Rec Tensile N Rec 0.14 Shear V Rec 0.14
HRD-U-10 1.8 2.0 1.2 1.2 1.2 1.2 0.25 0.25 1.2 1.2 0.6 0.8
HRD-U-14 2.3 2.5 1.6 1.6 1.3 1.5 0.3 0.3 1.5 1.5 0.6 1.0
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions adjacent. Please consult Hilti Fastening Technology Manual for specific design requirements.
HRD-UGT 8 60/10 HRD-UGT 8 80/30 HRD-UGT 8100/50 HRD-UGT 8120/70 HRD-UGT 8140/90
8 8 8 8 8
50 50 50 50 50
10 30 50 70 90
50 50 50 50 50
incl. 1 Bit TX 30 incl. 1 Bit TX 30 incl. 1 Bit TX 30 incl. 1 Bit TX 30 incl. 1 Bit TX 30
HRD-UGT Version: anchor body and T40-head screw, steel zinc plated
Hole dia., d (mm)
o
Package contents
Ordering designation
Item no.
10 10 10 10 10 10
80 80 80 80 80 80
10 30 50 70 90 110 10 50
70 70 70 70 70 70 70 70
50 50 50 50 50 50 50 50
HRD-UGT 10 80/ 10 HRD-UGT 10100/ 30 HRD-UGT 10120/ 50 HRD-UGT 10140/ 70 HRD-UGT 10160/ 90 HRD-UGT 10180/110 HRD-URT 10 80/ 10 HRD-URT 10120/ 50
00257289 00257290
299
Anchor Systems
HRD-UGS Version: with hexagon-head screw 13 mm across flats, steel zinc plated
Hole dia., d (mm)
o
A4 316
Package contents Ordering designation Item no.
10 10 10 10 10 10 10 10 10
80 80 80 80 80 80 80 80 80
10 30 50 70 110 10 30 50 70
70 70 70 70 70 70 70 70 70
50 50 50 50 50 50 50 50 25
HRD-UGS 10 80/ 10 HRD-UGS 10100/ 30 HRD-UGS 10120/ 50 HRD-UGS 10140/ 70 HRD-UGS 10180/110 HRD-URS 10 80/ 10 HRD-URS 10100/ 30 HRD-URS 10120/ 50 HRD-URS 10140/ 70
Package contents
Ordering designation
Item no.
14 14 14 14 14 14 14 14 14 14
80 80 80 80 80 80 80 80 80 80
70 70 70 70 70 70 70 70 70 70
50 50 50 50 50 50 50 50 50 50
HRD-UGS 14 80/ 10 U HRD-UGS 14110/ 40 U HRD-UGS 14140/ 70 U HRD-UGS 14160/ 90 U s HRD-UGS 14180/110 U s HRD-UGS 14200/130 U s HRD-UGS 14230/160 U s HRD-UGS 14270/200 U s HRD-UGS 14310/240 U s HRD-UGS 14350/280 U
00312632 00312633 00312634 00312635 00312636 00312637 00312638 00312639 00312640 00312641
Package contents
Ordering designation
Item no.
14 14 14 14 14 14 14 14 14 14
80 80 80 80 80 80 80 80 80 80
70 70 70 70 70 70 70 70 70 70
50 50 50 50 50 50 50 50 50 50
HRD-UGT 14 80/ 10 HRD-UGT 14110/ 40 HRD-UGT 14140/ 70 HRD-UGT 14160/ 90 s HRD-UGT 14180/110 s HRD-UGT 14200/130 s HRD-UGT 14230/160 s HRD-UGT 14270/200 s HRD-UGT 14310/240 s HRD-UGT 14350/280
00312622 00312623 00312624 00312625 00312626 00312627 00312628 00312629 00312630 00312631
Cover caps
Description
Box Quantity
Item no.
100 100
00246780 00246782
Description
TEC-HIS
Package contents
to hex socket) )
Item no.
1 1
to hex socket)
(Driven end: 1/ hex as per DIN 3126 / E 6.3, Driving end: 1/ hex as per DIN 3126 / C 6.3)
4
Description
Length (mm)
Package contents
Ordering designation
Item no.
Bit holder, steel, short, magnetic Bit holder, steel, long, magnetic Bit holder with locking sleeve, magnetic Bit holder 75m SDS Bit (hex) for HRD 8 Bit (hex) for HRD 10 Bit (hex) for HRD 14
50 75 50 75
1 1 1 1 1 1 1
S-BH50M S-BH75M S-BHU50M S-BHU75M SDS Torx T30 Torx T40 Torx T50
S-BH50M / S-BH75M
S-BHU50M
S-BHU75M SDS
T30/T40 / T50
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie Hilti. Outperform. Outlast.
300
Anchor Systems
HKD-E
Thread size
M 16 65 20
69
11.5
12.9
25
Anchor Body
Hole dia. (mm) Anchor length (mm) Hole depth (inch) Embedment Box depth (mm) quantity Ordering designation Item no.
HSD-G 16 dowel punch EDP 16 dowel punch (across cavity) EAP 16 anchor punch s (across cavity)
14 14 14
70 100 135
90 90 90
70 70 70
50 50 50
Scaffold Ringbolt
Internal ring dia. (mm) Overall shank length (mm) Thread dia (inch) Ordering designation Item no.
54
127
16
ST-127-M16 ringbolt M16 ringbolt adaptor HKD 16 anchor FC 16 filler cap (grey)
12 12 12 12 12 12
23 + 2 23 + 2 23 + 2 23 + 2 23 + 2 23 + 2
25 25 25 25 25 25
GRS 12/ 90 GRS 12/ 120 GRS 12/ 160 GRS 12/ 190 GRS 12/ 230 GRS 12/ 350
M16
20
80
10
00224004 00255590
For use with M16 ringbolt only. Can be tightened with a standard scaffolding spanner. Anchor is designed for Tensile loads only.
27
50
VST 14
00056440
10
* 5 metres length
37
19
00310901 00057318
Hilti test meter equipment Mark V for details see page 309
s PLEASE ASK FOR DELIVERY DETAILS.
301
Anchor Systems
ls
ls
1
d0 d0
tfix
tfix
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
Item no.
8 8 8 8 10 10 10 12 12 12 12 12 12 12
20 32 38 45 38 52 65 38 52 65 80 54 66 83
25 39 45 52 45 58 71 45 58 71 88 60 70 90
M4 M4 M4 M4 M5 M5 M5 M6 M6 M6 M6 M8 M8 M8
4 6 12 19 8 12 25 9 12 24 40 12 24 40
HHD-S M4/ 420 HHD-S M4/ 632 HHD-S M4/1238 HHD-S M4/1945 HHD-S M5/ 838 HHD-S M5/1252 HHD-S M5/2565 HHD-S M6/ 938 HHD-S M6/1252 HHD-S M6/2465 HHD-S M6/4080 HHD-S M8/1254 HHD-S M8/2466 HHD-S M8/4083
00332060 00332061 00332062 00332063 00332065 00332066 00332067 00332069 00332070 00332071 00332072 00332073 00332074 00332075
Setting tool
For thread size Packaging Ordering contents (pcs) designation Item no.
Setting tool
M4M8
HHD-SZ2
00332076
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
302
Anchor Systems
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
HLD
Hole dia., (solid material) d (mm)
o
Package contents
Ordering designation
Item no.
10 17 26
Quick and easy The zinc-plated steel HSP (Hilti Speed Plug) and glass-fibre reinforced polyamide HFP (Hilti Fibre Plug) are ideal for light-duty fastenings in drywall panels. One bit that fits for the anchors and the screws allows a fast and easy setting process. Features n Sharks tooth design for correct positioning and quick installation n Cuts its own thread n One Hilti bit for anchor and screw. No setting tool required. n Hilti HSP also available with F7, M6, / connecting thread n HSP and HFP delivered with or without screws
1 4
Setting operations
4 4,5 mm #8
Push the teeth of the Drive the anchor anchor into the drywall (clockwise rotation) panel. until it lies flush with the wall.
HSP
HSP-S
Anchor length ld (mm) Screw dia. (mm) Packaging contents (pcs) Ordering designation Item no.
39 4.5 100 HSP 39 4.5 100 HSP-S * 39 100 HSP-M6 * 29 4.5 100 HFP 29 4.5 100 HFP-S * 5 D-B PH2 HSP/HFP 5 D-B SQ HSP-G ** Delivered with 100 screws, 4.5 mm 30 mm
HFP
HFP-S Bit for HSP with connecting thread / /M6/F7 (D-B SQ HSP-G)
1 4
303
Anchor Systems
Base materials Concrete, solid brick, sand-lime block, aerated / gas concrete, hollow block, vertically perforated brick Fastening of wooden laths / timber battens, drywall studs, framing, metal sections and mouldings, electrical installation components, mechanical installations (plumbing / pipefitting), cable trunking, pipe rings, sheeting / foils, etc. Setting operations
Fastening wooden laths Notes on setting If used in perforated or hollow blocks, the anchor length must ensure that the expansion section is in at least one block web. The anchor should be used solely for through fastening.
l l
d0 hnom h1 tfix
d0 hnom h1 tfix
4 2 25 20 20 250 HPS-1 4/ 020 00260369 00260395 5 2 25 20 20 250 HPS-1 5/ 020 5 5 30 20 25 200 HPS-1 5/ 525 00260347 00260357 5 10 30 20 30 200 HPS-1 5/1030 00230515 00230524 5 15 30 20 35 200 HPS-1 5/1535 00260348 00260358 6 2 40 25 25 150 HPS-1 6/ 025 00238159 00238161 00260349 00260359 6 5 40 25 30 150 HPS-1 6/ 530 40 25 35 150 HPS-1 6/1035 6 10 00230516 00230525 6 15 40 25 40 150 HPS-1 6/1540 00260350 00260360 6 25 40 25 50 100 HPS-1 6/2550 00260351 00260361 6 30 40 25 55 100 HPS-1 6/3055 00230517 00230526 00260352 00260362 6 40 40 25 65 100 HPS-1 6/4065 8 10 50 30 40 100 HPS-1 8/1040 00260353 00260363 8 20 50 30 50 50 HPS-1 8/2050 00230518 00230527 8 30 50 30 60 50 HPS-1 8/3060 00260354 00260364 8 40 50 30 70 50 HPS-1 8/4070 00230519 00230528 8 60 50 30 90 50 HPS-1 8/6090 00260355 00260365 8 80 50 30 110 50 HPS-1 8/80110 00260356 00260366 In addition, we offer various other versions, e.g. with a counter-sunk head, connection thread, coloured screw head and anchor body, etc.
HPS-1 Combi Pack Version: with prefitted drive screw of zinc plated steel
Hole dia. (mm) Max. fixture thickness tfix (mm) Min. hole depth h1 (mm) Anchor length l (mm) Packaging contents (pcs) Ordering designation Item no.
5 5 6 6 6 6 8 8 8
5 15 10 15 25 40 10 60 80
30 30 40 40 40 40 50 50 50
25 35 35 40 50 65 40 90 110
5/ 5 combo 5/15 combo 6/10 combo 6/15 combo 6/25 combo 6/40 combo 8/10 combo 8/60 combo 8/80 combo
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie Hilti. Outperform. Outlast.
304
Anchor Systems
h1
tfix
Features n Setting by impact expansion n Automatic follow-up expansion, thus safe fastening n Fastening of lathes (DBZ 6/35) n Fire resistance
Min. anchorage h
depth (mm)
nom
rec
rec
(kN)
(kN)
Package contents
Ordering designation
Item no.
6 6
49 79
41 41
4.5 35
32 72
0.8 0.8
1.1 1.1
100 100
00256312 00256311
h1 hnom
HA 8
Hole dia., d (mm)
o
8 8
rec
(kN)
Package contents
Ordering designation
Item no.
50 50
12-15 12-15
5 5
40 40
0.8 0.8
100 100
HA 8 R1 (ring) HA 8 R1 (hook)
00057059 00057036
Box Quantity
Hole dia.
Item no.
Ceiling hanger
100
6.5mm
00253664
Box Quantity
Item no.
305
Anchor Systems
Setting instructions
7
I 50mm do h1 tfix
Technical data do Nominal drill bit diameter h1 Min. hole depth tfix Max. insulation thickness I Fastener length Min. embedment depth
8x70 8 40 40 70 30
8x90 8 40 60 90 30
8x110 8 40 80 110 30
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
Package contents
Ordering designation
Item no.
8 8 8 8 8 8 8 8
40 40 40 40 40 40 40 40
IZ top plate as an additional part, 90 mm dia., for fastening soft insulation materials
Package contents Ordering designation Item no.
100
HDT 90
285627
s PLEASE ASK FOR DELIVERY DETAILS. For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387
306
Anchor Systems
do
Technical data do Nominal drill bit diameter h1 Min. hole depth tfix Max. fastenable thickness I Fastener length
tfix
0/2 8 50 20 50
2/4 8 50 40 70
4/6 8 50 60 90
6/8 8 50 80 110
h1
IDP
Max. insulation thickness, t (mm)
fix
Package contents
Ordering designation
Item no.
8 8 8 8 8 8 8
50 50 50 50 50 50 50
IDP 0/ 2 IDP 2/ 4 IDP 4/ 6 IDP 6/ 8 IDP 8/10 IDP 10/12 IDP 13/15
Ordering designation
Base material n Concrete n Lightweight concrete n Solid brick n Cavity/perforated brick Use n Fastening insulating materials beneath cladding/facade panels where IDMR non-flammable material is specified Material n Sheet steel, Sendzimir zinc plated, building material class A as per DIN 4102. l Technical data do Nominal drill bit diameter h1 Min. hole depth tfix Max. fastenable thickness do I Fastener length
h1 tfix
0/3 8 55 30 80
3/6 8 55 60 110
6/9 8 55 90 140
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions above. Please consult Hilti Fastening Technology Manual for specific design requirements.
Package contents
Ordering designation
Item no.
up to 30 30- 60 60- 90
For use with:
80 110 140
8 8 8
55 55 55
IDMR-T insulation plates as accessories, 80 mm dia., for IDMR to secure soft insulating material
Insulation disc Stainless steel expansion pin Setting punch for expansion pin 250 250 1 IDMR-T 00065789 00065728 00065729
307
Anchor Systems
NOTE: These figures are given for single anchors without influence from neighbouring anchors or concrete edges and the conditions adjacent. Please consult Hilti Fastening Technology Manual for specific design requirements.
5 6 8 10 12 14
25 30 40 50 60 70
Anchor length (mm)
HUD-1 525 HUD-1 630 HUD-1 840 HUD-1 1050 HUD-1 1260 HUD-1 1470
Ordering designation
6 8 10
Screw shank dia. (mm)
70 80 90
Screw length (mm) Head shape
50 60 70
810 1012 7 8
24 5 4, 6, 8 33 6 6, 8, 10, 12 40 7 10, 12, 14 33 6 6, 8, 10, 12 (5000 red plastic plugs + 20 HM 6/10 masonry bits) 40 7 10, 12, 14 (3000 brown plastic plugs + 12 HM 7/10 masonry bits)
Yellow plastic plug Red plastic plug Brown plastic plug Supersaver tub Supersaver tub
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie
308
Anchor Systems
10 10 10
20 20 20
General Purpose Tester Kit Kit contains: Tester with 20 kN or 5 kN fixed gauge with maximum load indicator, standard load spreading bridge; 6 threaded button adaptors (M4, M5, M6, M8, M10 and M12); 6 plain slotted adaptors (internal diameter 4.5, 5.5, 6.5, 10.5 and 12.5 mm); 2 threaded rod adaptors (M4, M5); set screw and washer set (M6, M8, M10, M12, M16); bolt tester adaptor; 22 mm hex. operating nut (alternative handle for confined spaces); calibration certificate and method statement. Supplied in robust Hilti case. Item numbers: (with 20 kN gauge) s 03080198 (with 5 kN gauge) s 03080197 Scaffold Ring Bolt Tester Kit The new NASC/CFA Guidance Note TG4:04 Anchorage Systems for Scaffolding sets out requirements for Preliminary Tests of scaffold anchors (to check the suitability and allowable loads of an anchor type in a particular base material) and Proof Tests (sample tests to check that anchors have been installed correctly) to be carried out on all jobs. Kit contains: Tester with fixed gauge calibration to 20 kN; 150 mm load spreading bridge with 75 mm hex legs; M12 clevis adaptor with locking adaptor, Bolt tester adaptor; M16 threaded stud adaptor; M12 button adaptor; Calibration Certificate and Method Statement. Supplied in robust Hilti case. Item number: s 03080199 Wall Tie Tester Kit Kit contains: Tester with 5 kN fixed gauge with maximum load indicator, 100 mm wall tie spacer bridge; M5 and M6 wall tie adaptors (threaded rod adaptors); 2 x M12 threaded button adaptors; calibration certificate and method statement. Supplied in robust Hilti case. Heavy duty Tester Kit and Master Kit. Item number:
12 12 12
20 20 20
10 10 10
20 20 20
12 12 12
20 20 20
Setting tool
s 03080201
00058256
Ordering designation
Item no.
0-25 168 12 20 50-80 218 12 20 80-110 248 12 20 110-140 278 12 20 Use with HIT-S sieve for hollow brickwork
Master Kit The Hilti Field Engineers Kit Covers most testing applications up to 20 kN* Kit contains: Test with 2 interchangeable gauges (0-5,k 0-20 kN) standard 150 load spreading bridge; 6 threaded button adaptors (M4, M5, M6, M8, M10 and M12); 6 plain slotted adaptors (internal diameters 4.5, 5.5, 6.5, 8.5, 10.5, 12.5 mm); 2 threaded rod adaptors (M4, M5); M16, M20 and 5/8 Whitworth stud adaptors; M12 clevis adaptor with ring bolt adaptor, set screw and washer set (M6, M8, M10, M12, M16); bolt tester adaptor; insulation fastener adaptor, 50 mm and 100 mm hex. extension legs sets; calibration certificate and method statements. Supplied in a large red padded steel carrying case. Item number: s 03080200 www.hilti.co.uk | 0800 886 100 www.hilti.ie | 1850 287 387
309
Anchor Systems
Hilti HRS Timber Rail tie A repair concept for old timber ties
Features: n HRS can be set simply and quickly n No special tools required n Suitable for all screw spikes in common use n Convenient and inexpensive method As trains rush by and the years slip past, timber rail ties begin to rot and rail anchoring screws corrode. It is no surprise that the hold they once provided is no longer what it should be. The rail ties then have to be replaced. Would not it be possible, in many cases, to extend the life of these ties by several years? HRS the problem solver Hiltis HRS anchor now makes it possible to restore the holding power of rail screw spikes in ties which are otherwise still perfectly serviceable conveniently and inexpensively.
Ordering designation Item no.
HRS 22
00216962 Computer-designed thread flanks The thread flanks provide a secure keying hold in the timber tie, with good long-term characteristics under dynamic loading. The HRS is expanded by the screw shank, making it insensitive to variances in screw geometry.
HRA
HRC
HRT
For further Technical Information see Fastening Technology Manual or visit the website or call Hilti TAS on (GB) 0161 886 1144 or (IRL) 1850 287 387 0800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie
310