You are on page 1of 49

Automotive Wave forms

Oscilloscope's

An oscilloscope can be a priceless price of test equipment used for observation of electrical/electronic wave patterns.

Oscilloscope's

To properly use an oscilloscope you must understand the scale selections. Must automotive oscilloscope will automatically adjust to the proper scale. Its the technician job to interpret the reading and determine if the wave form is normal or defective. Not all devices operate in the same manner please check manufactures specifications before replacing any sensor.

Oscilloscope's

Oscilloscope are used to measure voltage over a period of time. An event that happens over a period of time is called frequency and in measured in Hertz per second.

20

V O L T A G E

15 10 5

0
5 10 15 1 Second Scale

TIME

Grid lines
15 12.2 filter DC voltage V O L T A G E 4 Volts Peak to Peak AC Voltage 0 5 6 9 volts unfiltered DC voltage

10

10

1 Second scale

Oscilloscope's

Filtered voltage: A smooth supply of voltage. Unfiltered voltage: Normally a ripple type wave pattern.

Oscilloscope's

An AC wave form change direction from positive to negative. Peak voltage: is the voltage from the highest positive voltage to the lowest negative voltage reading.

+5 0 -5

Peak to Peak voltage is determine by multiplying:

Grid division x voltage setting = Peak to peak voltage

Oscilloscope's

Oscilloscope can be used to measure an event over a period of time.

Frequency: Number of complete cycles per second measured in hertz (Hz). Hertz (Hz): Unit of measurement for frequency. 1 hertz equal 1 cycle per second.

Oscilloscope's

To check frequency you may need some math. Number of grid lines covered for 1 cycle divided by the time scale.

Wheel speed sensor

The Anti-lock Braking System (ABS) relies upon information coming in from speed sensors. The wave form produced is used by the ABS control module to determine if wheel lock-up is occurring.

Two ABS wave forms. Both are good the difference is the meter set-up

2 V O L T S C A L E 5 mS Time Scale NORAM ABS PATTERN

2
V O L T S C A L E

2 Volts

10 mS

10 mS Time Scale Normal ABS Pattern

Throttle Position Sensor

A throttle position is normally produces an analog signal. The throttle position is normally used to tell the PCM the position of the throttle Analog signal: an electrical signal that varies in strength.

Throttle Held open

Throttle Snapped

5 4 3

2
1 0 200 mS Time Division Normal Throttle Position Wave Form Most throttle position can be easily seen on the 200 mS scale

5 4 3

Defective TPS

2
1 0 200 mS Time Division Normal Throttle Position Wave Form Most throttle position can be easily seen on the 200 mS scale

Air Flow Meters

The voltage output from the internal track of an Air Flow Meter (AFM) should be linear to flap movement, This can be measured on an oscilloscope

MASS AIR FLOW METER

The waveform should show approximately 1.0 volt when the engine is at idle, Voltage will rise as engine when engine speed is increased. A peak voltage of around 4.5 is normal due to natural inertia. Voltage will drop and then level off

Spike due to acceleration

Normal float back to match air flow Throttle Released Normal falloff caused by inertia

Around 1 Volt at idle

Hot Wire Air flow Meters


Voltage spike due to quick throttle opening
5 4 3 2 1 0 Cold air cooling of wire Throttle Released Temperature stabilizes

At idle around 1 volt normal


250 mS time division

A defective Mass Air Flow will have low voltage or operate erratic at all throttle angles.

A mass air flow angle should change in relation to throttle angle. 5 4 3 2 1 0 250 mS time division

Wave Forms

Another common type wave form is the square wave. Most electronic components are controlled by a computer PCM, BCM, ECM, ECU or a host of other names. When the computer turns on a component it usually completes a ground circuit sometime controlling a relay.

Square Wave

Normal voltage spikes

15 10

5
0 Normal Square wave. NOTE: Any wave that is on more than off or off ore than on is called a pulsed wave.

Pulsed Wave

Pulsed waves are used to control several electrical components such as:
Fuel pump Canister solenoids EGR solenoids Wave length: The time required for on complete cycle of a waveform.

Pulsed Wave
. The difference in wave length is caused by circuit demands 20 15 10 5 0 NORMAL PULSE WAVE Wave length

Pulsed Wave
. Voltage did not drop properly

20 15 10 5 0

Bad pulse wave Voltage did increase properly

Coolant Temperature Sensor (CTS)

Most coolant sensors are Negative Temperature Coefficient (NTC) devices. The sensor resistance starts out high around 200 Ohms and drops as engine temperature increases.

Bad CTS wave form

V O L 5 4 3 Good CTS waveform

T
S

2
1 0 50 100 150 200 50 second scale 250

Bad CTS wave forms

V O L 5 4 3 Bad CTS erratic voltage pattern Bad CTS sensor or electrical connection disconnected waveform

T
S

2
1 0 50 100 150 200 50 second scale 250

Crankshaft Sensor

This signal should be test when the engine fail to start due to lack ignition. The crankshaft sensor produces an AC voltage that is low while cranking and increases after the engine starts. AC voltage output is critical, low output can prevent an engine from starting.

Even if the signal pattern look good.

Crankshaft Sensor

Normal due to missing tooth on reluctor or flywheel.

The missing tooth is used by the PCM to determine crankshaft position

Crankshaft Sensor

Voltage at start-up

Voltage at higher cranking RPM

NOTE: Operating parameters vary from manufactures

Crankshaft Sensor

Engine Running: Note the higher voltage

Crankshaft Sensor

A defective crankshaft sensor will show little or no output on the oscilloscope Proper output voltage is critical.

1 .8 .6 .4 .2 0 Defective Crankshaft sensor Voltage to LOW

.2
.4

Knock Sensor

A knock sensor is used with some management systems, The Knock sensor is a small piezo-electrical device. That produces electricity when vibrated. Knock sensor are used to reduce ignition timing when a spark knock occurs. Usually no more than 10

Knock Sensor

Knock Sensor

V O L T A G 5 4 3 2 1 0 1 NOTE: Knock sensor output should normally be zero

Point where knock occurred

50

100

150

200

250

300

350

50 mS scale

Knock Sensor

5 4 3

Bad knock sensor pattern

2
1 0 50 100 150 200 250 300

Oscilloscope's

Its important to remember that all electrical wiring will have some type electrical pattern that can be view on an oscilloscope.

Open Circuit NOTE: Voltage is 0 on an open circuit

Good ground circuit

Oscilloscope's Quiz

1. Technician A says pattern A is DC voltage. Technician B says Pattern B is DC voltage. Who is correct. A. Technician A only B. Technician B only C. Both A and B D. Neither A nor B

Pattern A

Pattern B

Oscilloscope's Quiz

2. How many seconds pass from point A to Pont B?


A. 1 B. 2 C. 3 4. 4
A B

1 Second Scale

Oscilloscope's Quiz

3. Technician A says this pattern is an AC wave form. Technician B says this is DC unfiltered. Who is correct? A. Technician A Only B. Technician B only C. Both A and B D. Neither A nor B

22 11

00 11
22

Oscilloscope's Quiz

4. What is peak Negative voltage in this pattern? A. - 1 volt B. - 2 volts C. - 4 volts D. -.25 volts

2 1 0 1 2 50 100 150 200

Oscilloscope's Quiz

5. What is peak to peak voltage in this pattern? A. 1 volt B. 2 volts C. 4 volts D. .25 volts

2 1 0 1 2 50 100 150 200

Oscilloscope's Quiz

6. The number of complete cycles per second measured is:


A. Amperage B. Frequency C. Ohms D. Voltage

Oscilloscope's Quiz

7. Technician A says voltage is measured from point A - B. Technician B says Time is measure from point C-D. Who is correct? A. Technician A only B. Technician B only C. Both A and B D. Neither A nor B

Oscilloscope's Quiz

8. What time scale is this oscilloscope set for?


A. 2 mS B. 5 mS C. 10 mS D. 100 mS

Oscilloscope's Quiz

9. Technician A says the wave form is of a defective TPS (Throttle position sensor) Technician B says the pattern is of a good CTS sensor. Who is correct? A. Technician A only B. Technician B only C. Both A and B D. Neither A nor B

5 4 3

2
1 0 50 100 150 200 250 50 Second Scale

Oscilloscope's Quiz

10. Which diagram is of a good ground circuit?


A. 1 B. 2 C. 3 D. 4

You might also like